Skip to contentSkip to conversation

ACPI: PCI: IRQ: Handle INTx GSIs as u32 values not int

PATCH In review Lorenzo Pieralisi 2 participants 4 messages Dec 31, 2025 – Jan 2

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ACPI: PCI: IRQ: Handle INTx GSIs as u32 values not int

In ACPI Global System Interrupts (GSIs) are described using a 32-bit value.

ACPI/PCI legacy interrupts (INTx) parsing code treats GSIs as 'int', which poses issues if the GSI interrupt value is a 32-bit value with the MSB set (as required in some interrupt configurations - eg ARM64 GICv5 systems).

Fix ACPI/PCI legacy INTx parsing by converting variables representing GSIs from 'int' to 'u32' bringing the code in line with the ACPI specification.

Cc Len Brown <[email protected]>
Cc Bjorn Helgaas <[email protected]>
Cc "Rafael J. Wysocki" <[email protected]>
---
 drivers/acpi/pci_irq.c      | 19 ++++++++++--------
 drivers/acpi/pci_link.c     | 39 ++++++++++++++++++++++++-------------
 drivers/xen/acpi.c          | 13 +++++++------
 include/acpi/acpi_drivers.h |  2 +-
 4 files changed, 44 insertions(+), 29 deletions(-)
drivers/acpi/pci_irq.c +11 -8
index ad81aa03fe2f..c416942ff3e2 100644
@@ -188,7 +188,7 @@ static int acpi_pci_irq_check_entry(acpi_handle handle, struct pci_dev *dev,
 	 * the IRQ value, which is hardwired to specific interrupt inputs on
 	 * the interrupt controller.
 	 */
-	pr_debug("%04x:%02x:%02x[%c] -> %s[%d]\n",
+	pr_debug("%04x:%02x:%02x[%c] -> %s[%u]\n",
 		 entry->id.segment, entry->id.bus, entry->id.device,
 		 pin_name(entry->pin), prt->source, entry->index);
 
@@ -384,7 +384,7 @@ static inline bool acpi_pci_irq_valid(struct pci_dev *dev, u8 pin)
 int acpi_pci_irq_enable(struct pci_dev *dev)
 {
 	struct acpi_prt_entry *entry;
-	int gsi;
+	u32 gsi;
 	u8 pin;
 	int triggering = ACPI_LEVEL_SENSITIVE;
 	/*
@@ -422,18 +422,21 @@ int acpi_pci_irq_enable(struct pci_dev *dev)
 			return 0;
 	}
 
+	rc = -ENODEV;
+
 	if (entry) {
 		if (entry->link)
-			gsi = acpi_pci_link_allocate_irq(entry->link,
+			rc = acpi_pci_link_allocate_irq(entry->link,
 							 entry->index,
 							 &triggering, &polarity,
-							 &link);
-		else
+							 &link, &gsi);
+		else {
 			gsi = entry->index;
-	} else
-		gsi = -1;
+			rc = 0;
+		}
+	}
 
-	if (gsi < 0) {
+	if (rc < 0) {
 		/*
 		 * No IRQ known to the ACPI subsystem - maybe the BIOS /
 		 * driver reported one, then use it. Exit in any case.
drivers/acpi/pci_link.c +25 -14
index bed7dc85612e..b91b039a3d20 100644
@@ -448,7 +448,7 @@ static int acpi_isa_irq_penalty[ACPI_MAX_ISA_IRQS] = {
 	/* >IRQ15 */
 };
 
-static int acpi_irq_pci_sharing_penalty(int irq)
+static int acpi_irq_pci_sharing_penalty(u32 irq)
 {
 	struct acpi_pci_link *link;
 	int penalty = 0;
@@ -474,7 +474,7 @@ static int acpi_irq_pci_sharing_penalty(int irq)
 	return penalty;
 }
 
-static int acpi_irq_get_penalty(int irq)
+static int acpi_irq_get_penalty(u32 irq)
 {
 	int penalty = 0;
 
@@ -528,7 +528,7 @@ static int acpi_irq_balance = -1;	/* 0: static, 1: balance */
 static int acpi_pci_link_allocate(struct acpi_pci_link *link)
 {
 	acpi_handle handle = link->device->handle;
-	int irq;
+	u32 irq;
 	int i;
 
 	if (link->irq.initialized) {
@@ -598,44 +598,53 @@ static int acpi_pci_link_allocate(struct acpi_pci_link *link)
 	return 0;
 }
 
-/*
- * acpi_pci_link_allocate_irq
- * success: return IRQ >= 0
- * failure: return -1
+/**
+ * acpi_pci_link_allocate_irq(): Retrieve a link device GSI
+ *
+ * @handle: Handle for the link device
+ * @index: GSI index
+ * @triggering: pointer to store the GSI trigger
+ * @polarity: pointer to store GSI polarity
+ * @name: pointer to store link device name
+ * @gsi: pointer to store GSI number
+ *
+ * Returns:
+ *	0 on success with @triggering, @polarity, @name, @gsi initialized.
+ *	-ENODEV on failure
  */
 int acpi_pci_link_allocate_irq(acpi_handle handle, int index, int *triggering,
-			       int *polarity, char **name)
+			       int *polarity, char **name, u32 *gsi)
 {
 	struct acpi_device *device = acpi_fetch_acpi_dev(handle);
 	struct acpi_pci_link *link;
 
 	if (!device) {
 		acpi_handle_err(handle, "Invalid link device\n");
-		return -1;
+		return -ENODEV;
 	}
 
 	link = acpi_driver_data(device);
 	if (!link) {
 		acpi_handle_err(handle, "Invalid link context\n");
-		return -1;
+		return -ENODEV;
 	}
 
 	/* TBD: Support multiple index (IRQ) entries per Link Device */
 	if (index) {
 		acpi_handle_err(handle, "Invalid index %d\n", index);
-		return -1;
+		return -ENODEV;
 	}
 
 	mutex_lock(&acpi_link_lock);
 	if (acpi_pci_link_allocate(link)) {
 		mutex_unlock(&acpi_link_lock);
-		return -1;
+		return -ENODEV;
 	}
 
 	if (!link->irq.active) {
 		mutex_unlock(&acpi_link_lock);
 		acpi_handle_err(handle, "Link active IRQ is 0!\n");
-		return -1;
+		return -ENODEV;
 	}
 	link->refcnt++;
 	mutex_unlock(&acpi_link_lock);
@@ -647,7 +656,9 @@ int acpi_pci_link_allocate_irq(acpi_handle handle, int index, int *triggering,
 	if (name)
 		*name = acpi_device_bid(link->device);
 	acpi_handle_debug(handle, "Link is referenced\n");
-	return link->irq.active;
+	*gsi = link->irq.active;
+
+	return 0;
 }
 
 /*
drivers/xen/acpi.c +7 -6
index d2ee605c5ca1..eab28cfe9939 100644
@@ -89,11 +89,11 @@ int xen_acpi_get_gsi_info(struct pci_dev *dev,
 						  int *trigger_out,
 						  int *polarity_out)
 {
-	int gsi;
+	u32 gsi;
 	u8 pin;
 	struct acpi_prt_entry *entry;
 	int trigger = ACPI_LEVEL_SENSITIVE;
-	int polarity = acpi_irq_model == ACPI_IRQ_MODEL_GIC ?
+	int ret, polarity = acpi_irq_model == ACPI_IRQ_MODEL_GIC ?
 				      ACPI_ACTIVE_HIGH : ACPI_ACTIVE_LOW;
 
 	if (!dev || !gsi_out || !trigger_out || !polarity_out)
@@ -105,17 +105,18 @@ int xen_acpi_get_gsi_info(struct pci_dev *dev,
 
 	entry = acpi_pci_irq_lookup(dev, pin);
 	if (entry) {
+		ret = 0;
 		if (entry->link)
-			gsi = acpi_pci_link_allocate_irq(entry->link,
+			ret = acpi_pci_link_allocate_irq(entry->link,
 							 entry->index,
 							 &trigger, &polarity,
-							 NULL);
+							 NULL, &gsi);
 		else
 			gsi = entry->index;
 	} else
-		gsi = -1;
+		ret = -ENODEV;
 
-	if (gsi < 0)
+	if (ret < 0)
 		return -EINVAL;
 
 	*gsi_out = gsi;
include/acpi/acpi_drivers.h +1 -1
index b14d165632e7..402b97d12138 100644
@@ -51,7 +51,7 @@
 
 int acpi_irq_penalty_init(void);
 int acpi_pci_link_allocate_irq(acpi_handle handle, int index, int *triggering,
-			       int *polarity, char **name);
+			       int *polarity, char **name, u32 *gsi);
 int acpi_pci_link_free_irq(acpi_handle handle);
 
 /* ACPI PCI Device Binding */
Signature · 1 line
2.50.1
Reviewed-by on v1 1/1
#1 lore raw
Quoted 10 lines · Lorenzo Pieralisi

In ACPI Global System Interrupts (GSIs) are described using a 32-bit value.

ACPI/PCI legacy interrupts (INTx) parsing code treats GSIs as 'int', which poses issues if the GSI interrupt value is a 32-bit value with the MSB set (as required in some interrupt configurations - eg ARM64 GICv5 systems).

Fix ACPI/PCI legacy INTx parsing by converting variables representing GSIs from 'int' to 'u32' bringing the code in line with the ACPI specification.

Looks good to me. Is there any symptom of what the issue looks like that could be mentioned here? Might also be useful in the subject, which currently describes the C code without really saying why we want to do this.

Quoted 224 lines
Cc Len Brown <[email protected]>
Cc Bjorn Helgaas <[email protected]>
Cc "Rafael J. Wysocki" <[email protected]>
---
 drivers/acpi/pci_irq.c      | 19 ++++++++++--------
 drivers/acpi/pci_link.c     | 39 ++++++++++++++++++++++++-------------
 drivers/xen/acpi.c          | 13 +++++++------
 include/acpi/acpi_drivers.h |  2 +-
 4 files changed, 44 insertions(+), 29 deletions(-)
drivers/acpi/pci_irq.c +11 -8
index ad81aa03fe2f..c416942ff3e2 100644
@@ -188,7 +188,7 @@ static int acpi_pci_irq_check_entry(acpi_handle handle, struct pci_dev *dev,
 	 * the IRQ value, which is hardwired to specific interrupt inputs on
 	 * the interrupt controller.
 	 */
-	pr_debug("%04x:%02x:%02x[%c] -> %s[%d]\n",
+	pr_debug("%04x:%02x:%02x[%c] -> %s[%u]\n",
 		 entry->id.segment, entry->id.bus, entry->id.device,
 		 pin_name(entry->pin), prt->source, entry->index);
 
@@ -384,7 +384,7 @@ static inline bool acpi_pci_irq_valid(struct pci_dev *dev, u8 pin)
 int acpi_pci_irq_enable(struct pci_dev *dev)
 {
 	struct acpi_prt_entry *entry;
-	int gsi;
+	u32 gsi;
 	u8 pin;
 	int triggering = ACPI_LEVEL_SENSITIVE;
 	/*
@@ -422,18 +422,21 @@ int acpi_pci_irq_enable(struct pci_dev *dev)
 			return 0;
 	}
 
+	rc = -ENODEV;
+
 	if (entry) {
 		if (entry->link)
-			gsi = acpi_pci_link_allocate_irq(entry->link,
+			rc = acpi_pci_link_allocate_irq(entry->link,
 							 entry->index,
 							 &triggering, &polarity,
-							 &link);
-		else
+							 &link, &gsi);
+		else {
 			gsi = entry->index;
-	} else
-		gsi = -1;
+			rc = 0;
+		}
+	}
 
-	if (gsi < 0) {
+	if (rc < 0) {
 		/*
 		 * No IRQ known to the ACPI subsystem - maybe the BIOS /
 		 * driver reported one, then use it. Exit in any case.
drivers/acpi/pci_link.c +25 -14
index bed7dc85612e..b91b039a3d20 100644
@@ -448,7 +448,7 @@ static int acpi_isa_irq_penalty[ACPI_MAX_ISA_IRQS] = {
 	/* >IRQ15 */
 };
 
-static int acpi_irq_pci_sharing_penalty(int irq)
+static int acpi_irq_pci_sharing_penalty(u32 irq)
 {
 	struct acpi_pci_link *link;
 	int penalty = 0;
@@ -474,7 +474,7 @@ static int acpi_irq_pci_sharing_penalty(int irq)
 	return penalty;
 }
 
-static int acpi_irq_get_penalty(int irq)
+static int acpi_irq_get_penalty(u32 irq)
 {
 	int penalty = 0;
 
@@ -528,7 +528,7 @@ static int acpi_irq_balance = -1;	/* 0: static, 1: balance */
 static int acpi_pci_link_allocate(struct acpi_pci_link *link)
 {
 	acpi_handle handle = link->device->handle;
-	int irq;
+	u32 irq;
 	int i;
 
 	if (link->irq.initialized) {
@@ -598,44 +598,53 @@ static int acpi_pci_link_allocate(struct acpi_pci_link *link)
 	return 0;
 }
 
-/*
- * acpi_pci_link_allocate_irq
- * success: return IRQ >= 0
- * failure: return -1
+/**
+ * acpi_pci_link_allocate_irq(): Retrieve a link device GSI
+ *
+ * @handle: Handle for the link device
+ * @index: GSI index
+ * @triggering: pointer to store the GSI trigger
+ * @polarity: pointer to store GSI polarity
+ * @name: pointer to store link device name
+ * @gsi: pointer to store GSI number
+ *
+ * Returns:
+ *	0 on success with @triggering, @polarity, @name, @gsi initialized.
+ *	-ENODEV on failure
  */
 int acpi_pci_link_allocate_irq(acpi_handle handle, int index, int *triggering,
-			       int *polarity, char **name)
+			       int *polarity, char **name, u32 *gsi)
 {
 	struct acpi_device *device = acpi_fetch_acpi_dev(handle);
 	struct acpi_pci_link *link;
 
 	if (!device) {
 		acpi_handle_err(handle, "Invalid link device\n");
-		return -1;
+		return -ENODEV;
 	}
 
 	link = acpi_driver_data(device);
 	if (!link) {
 		acpi_handle_err(handle, "Invalid link context\n");
-		return -1;
+		return -ENODEV;
 	}
 
 	/* TBD: Support multiple index (IRQ) entries per Link Device */
 	if (index) {
 		acpi_handle_err(handle, "Invalid index %d\n", index);
-		return -1;
+		return -ENODEV;
 	}
 
 	mutex_lock(&acpi_link_lock);
 	if (acpi_pci_link_allocate(link)) {
 		mutex_unlock(&acpi_link_lock);
-		return -1;
+		return -ENODEV;
 	}
 
 	if (!link->irq.active) {
 		mutex_unlock(&acpi_link_lock);
 		acpi_handle_err(handle, "Link active IRQ is 0!\n");
-		return -1;
+		return -ENODEV;
 	}
 	link->refcnt++;
 	mutex_unlock(&acpi_link_lock);
@@ -647,7 +656,9 @@ int acpi_pci_link_allocate_irq(acpi_handle handle, int index, int *triggering,
 	if (name)
 		*name = acpi_device_bid(link->device);
 	acpi_handle_debug(handle, "Link is referenced\n");
-	return link->irq.active;
+	*gsi = link->irq.active;
+
+	return 0;
 }
 
 /*
drivers/xen/acpi.c +7 -6
index d2ee605c5ca1..eab28cfe9939 100644
@@ -89,11 +89,11 @@ int xen_acpi_get_gsi_info(struct pci_dev *dev,
 						  int *trigger_out,
 						  int *polarity_out)
 {
-	int gsi;
+	u32 gsi;
 	u8 pin;
 	struct acpi_prt_entry *entry;
 	int trigger = ACPI_LEVEL_SENSITIVE;
-	int polarity = acpi_irq_model == ACPI_IRQ_MODEL_GIC ?
+	int ret, polarity = acpi_irq_model == ACPI_IRQ_MODEL_GIC ?
 				      ACPI_ACTIVE_HIGH : ACPI_ACTIVE_LOW;
 
 	if (!dev || !gsi_out || !trigger_out || !polarity_out)
@@ -105,17 +105,18 @@ int xen_acpi_get_gsi_info(struct pci_dev *dev,
 
 	entry = acpi_pci_irq_lookup(dev, pin);
 	if (entry) {
+		ret = 0;
 		if (entry->link)
-			gsi = acpi_pci_link_allocate_irq(entry->link,
+			ret = acpi_pci_link_allocate_irq(entry->link,
 							 entry->index,
 							 &trigger, &polarity,
-							 NULL);
+							 NULL, &gsi);
 		else
 			gsi = entry->index;
 	} else
-		gsi = -1;
+		ret = -ENODEV;
 
-	if (gsi < 0)
+	if (ret < 0)
 		return -EINVAL;
 
 	*gsi_out = gsi;
include/acpi/acpi_drivers.h +1 -1
index b14d165632e7..402b97d12138 100644
@@ -51,7 +51,7 @@
 
 int acpi_irq_penalty_init(void);
 int acpi_pci_link_allocate_irq(acpi_handle handle, int index, int *triggering,
-			       int *polarity, char **name);
+			       int *polarity, char **name, u32 *gsi);
 int acpi_pci_link_free_irq(acpi_handle handle);
 
 /* ACPI PCI Device Binding */
Signature · 1 line
2.50.1
#2 lore raw
Quoted 8 lines · Bjorn Helgaas
Quoted 7 lines · Lorenzo Pieralisi

In ACPI Global System Interrupts (GSIs) are described using a 32-bit value.

ACPI/PCI legacy interrupts (INTx) parsing code treats GSIs as 'int', which poses issues if the GSI interrupt value is a 32-bit value with the MSB set (as required in some interrupt configurations - eg ARM64 GICv5 systems).

Quoted 8 lines
Quoted 3 lines

Fix ACPI/PCI legacy INTx parsing by converting variables representing GSIs from 'int' to 'u32' bringing the code in line with the ACPI specification.

Looks good to me. Is there any symptom of what the issue looks like that could be mentioned here? Might also be useful in the subject, which currently describes the C code without really saying why we want to do this.

Thanks ! Happy New Year !

acpi_pci_link_allocate_irq() would return a GSI with MSB set, that the logic in acpi_pci_irq_enable() would treat as a failure because that's a negative value.

After fixing that - passing a 32-bit value with MSB set to acpi_irq_get_penalty() causes an array acpi_isa_irq_penalty dereference with an an index that is way beyond the array size.

This is not a fix per-se because GICv5 ACPI is not in the mainline, yet.

I can try to summarize the issue in the commit log.

Thanks,
Lorenzo

Quoted 227 lines
Quoted 224 lines
Cc Len Brown <[email protected]>
Cc Bjorn Helgaas <[email protected]>
Cc "Rafael J. Wysocki" <[email protected]>
---
 drivers/acpi/pci_irq.c      | 19 ++++++++++--------
 drivers/acpi/pci_link.c     | 39 ++++++++++++++++++++++++-------------
 drivers/xen/acpi.c          | 13 +++++++------
 include/acpi/acpi_drivers.h |  2 +-
 4 files changed, 44 insertions(+), 29 deletions(-)
drivers/acpi/pci_irq.c +11 -8
index ad81aa03fe2f..c416942ff3e2 100644
@@ -188,7 +188,7 @@ static int acpi_pci_irq_check_entry(acpi_handle handle, struct pci_dev *dev,
 	 * the IRQ value, which is hardwired to specific interrupt inputs on
 	 * the interrupt controller.
 	 */
-	pr_debug("%04x:%02x:%02x[%c] -> %s[%d]\n",
+	pr_debug("%04x:%02x:%02x[%c] -> %s[%u]\n",
 		 entry->id.segment, entry->id.bus, entry->id.device,
 		 pin_name(entry->pin), prt->source, entry->index);
 
@@ -384,7 +384,7 @@ static inline bool acpi_pci_irq_valid(struct pci_dev *dev, u8 pin)
 int acpi_pci_irq_enable(struct pci_dev *dev)
 {
 	struct acpi_prt_entry *entry;
-	int gsi;
+	u32 gsi;
 	u8 pin;
 	int triggering = ACPI_LEVEL_SENSITIVE;
 	/*
@@ -422,18 +422,21 @@ int acpi_pci_irq_enable(struct pci_dev *dev)
 			return 0;
 	}
 
+	rc = -ENODEV;
+
 	if (entry) {
 		if (entry->link)
-			gsi = acpi_pci_link_allocate_irq(entry->link,
+			rc = acpi_pci_link_allocate_irq(entry->link,
 							 entry->index,
 							 &triggering, &polarity,
-							 &link);
-		else
+							 &link, &gsi);
+		else {
 			gsi = entry->index;
-	} else
-		gsi = -1;
+			rc = 0;
+		}
+	}
 
-	if (gsi < 0) {
+	if (rc < 0) {
 		/*
 		 * No IRQ known to the ACPI subsystem - maybe the BIOS /
 		 * driver reported one, then use it. Exit in any case.
drivers/acpi/pci_link.c +25 -14
index bed7dc85612e..b91b039a3d20 100644
@@ -448,7 +448,7 @@ static int acpi_isa_irq_penalty[ACPI_MAX_ISA_IRQS] = {
 	/* >IRQ15 */
 };
 
-static int acpi_irq_pci_sharing_penalty(int irq)
+static int acpi_irq_pci_sharing_penalty(u32 irq)
 {
 	struct acpi_pci_link *link;
 	int penalty = 0;
@@ -474,7 +474,7 @@ static int acpi_irq_pci_sharing_penalty(int irq)
 	return penalty;
 }
 
-static int acpi_irq_get_penalty(int irq)
+static int acpi_irq_get_penalty(u32 irq)
 {
 	int penalty = 0;
 
@@ -528,7 +528,7 @@ static int acpi_irq_balance = -1;	/* 0: static, 1: balance */
 static int acpi_pci_link_allocate(struct acpi_pci_link *link)
 {
 	acpi_handle handle = link->device->handle;
-	int irq;
+	u32 irq;
 	int i;
 
 	if (link->irq.initialized) {
@@ -598,44 +598,53 @@ static int acpi_pci_link_allocate(struct acpi_pci_link *link)
 	return 0;
 }
 
-/*
- * acpi_pci_link_allocate_irq
- * success: return IRQ >= 0
- * failure: return -1
+/**
+ * acpi_pci_link_allocate_irq(): Retrieve a link device GSI
+ *
+ * @handle: Handle for the link device
+ * @index: GSI index
+ * @triggering: pointer to store the GSI trigger
+ * @polarity: pointer to store GSI polarity
+ * @name: pointer to store link device name
+ * @gsi: pointer to store GSI number
+ *
+ * Returns:
+ *	0 on success with @triggering, @polarity, @name, @gsi initialized.
+ *	-ENODEV on failure
  */
 int acpi_pci_link_allocate_irq(acpi_handle handle, int index, int *triggering,
-			       int *polarity, char **name)
+			       int *polarity, char **name, u32 *gsi)
 {
 	struct acpi_device *device = acpi_fetch_acpi_dev(handle);
 	struct acpi_pci_link *link;
 
 	if (!device) {
 		acpi_handle_err(handle, "Invalid link device\n");
-		return -1;
+		return -ENODEV;
 	}
 
 	link = acpi_driver_data(device);
 	if (!link) {
 		acpi_handle_err(handle, "Invalid link context\n");
-		return -1;
+		return -ENODEV;
 	}
 
 	/* TBD: Support multiple index (IRQ) entries per Link Device */
 	if (index) {
 		acpi_handle_err(handle, "Invalid index %d\n", index);
-		return -1;
+		return -ENODEV;
 	}
 
 	mutex_lock(&acpi_link_lock);
 	if (acpi_pci_link_allocate(link)) {
 		mutex_unlock(&acpi_link_lock);
-		return -1;
+		return -ENODEV;
 	}
 
 	if (!link->irq.active) {
 		mutex_unlock(&acpi_link_lock);
 		acpi_handle_err(handle, "Link active IRQ is 0!\n");
-		return -1;
+		return -ENODEV;
 	}
 	link->refcnt++;
 	mutex_unlock(&acpi_link_lock);
@@ -647,7 +656,9 @@ int acpi_pci_link_allocate_irq(acpi_handle handle, int index, int *triggering,
 	if (name)
 		*name = acpi_device_bid(link->device);
 	acpi_handle_debug(handle, "Link is referenced\n");
-	return link->irq.active;
+	*gsi = link->irq.active;
+
+	return 0;
 }
 
 /*
drivers/xen/acpi.c +7 -6
index d2ee605c5ca1..eab28cfe9939 100644
@@ -89,11 +89,11 @@ int xen_acpi_get_gsi_info(struct pci_dev *dev,
 						  int *trigger_out,
 						  int *polarity_out)
 {
-	int gsi;
+	u32 gsi;
 	u8 pin;
 	struct acpi_prt_entry *entry;
 	int trigger = ACPI_LEVEL_SENSITIVE;
-	int polarity = acpi_irq_model == ACPI_IRQ_MODEL_GIC ?
+	int ret, polarity = acpi_irq_model == ACPI_IRQ_MODEL_GIC ?
 				      ACPI_ACTIVE_HIGH : ACPI_ACTIVE_LOW;
 
 	if (!dev || !gsi_out || !trigger_out || !polarity_out)
@@ -105,17 +105,18 @@ int xen_acpi_get_gsi_info(struct pci_dev *dev,
 
 	entry = acpi_pci_irq_lookup(dev, pin);
 	if (entry) {
+		ret = 0;
 		if (entry->link)
-			gsi = acpi_pci_link_allocate_irq(entry->link,
+			ret = acpi_pci_link_allocate_irq(entry->link,
 							 entry->index,
 							 &trigger, &polarity,
-							 NULL);
+							 NULL, &gsi);
 		else
 			gsi = entry->index;
 	} else
-		gsi = -1;
+		ret = -ENODEV;
 
-	if (gsi < 0)
+	if (ret < 0)
 		return -EINVAL;
 
 	*gsi_out = gsi;
include/acpi/acpi_drivers.h +1 -1
index b14d165632e7..402b97d12138 100644
@@ -51,7 +51,7 @@
 
 int acpi_irq_penalty_init(void);
 int acpi_pci_link_allocate_irq(acpi_handle handle, int index, int *triggering,
-			       int *polarity, char **name);
+			       int *polarity, char **name, u32 *gsi);
 int acpi_pci_link_free_irq(acpi_handle handle);
 
 /* ACPI PCI Device Binding */
Signature · 1 line
2.50.1
#3 lore raw
Quoted 13 lines · Lorenzo Pieralisi
Quoted 12 lines · Bjorn Helgaas
Quoted 10 lines · Lorenzo Pieralisi

In ACPI Global System Interrupts (GSIs) are described using a 32-bit value.

ACPI/PCI legacy interrupts (INTx) parsing code treats GSIs as 'int', which poses issues if the GSI interrupt value is a 32-bit value with the MSB set (as required in some interrupt configurations - eg ARM64 GICv5 systems).

Fix ACPI/PCI legacy INTx parsing by converting variables representing GSIs from 'int' to 'u32' bringing the code in line with the ACPI specification.

Quoted 6 lines
Quoted 4 lines

Looks good to me. Is there any symptom of what the issue looks like that could be mentioned here? Might also be useful in the subject, which currently describes the C code without really saying why we want to do this.

Thanks ! Happy New Year !

Happy New Year!

Quoted 7 lines

acpi_pci_link_allocate_irq() would return a GSI with MSB set, that the logic in acpi_pci_irq_enable() would treat as a failure because that's a negative value.

After fixing that - passing a 32-bit value with MSB set to acpi_irq_get_penalty() causes an array acpi_isa_irq_penalty dereference with an an index that is way beyond the array size.

Ouch, out-of-bounds reference. Best case, maybe a data page fault or a "No IRQ available" message or just a suboptimal IRQ choice.