FAILED: patch "[PATCH] arm64: dts: ti: k3-j721e-sk: Fix pinmux for pin Y1 used by" failed to apply to 6.1-stable tree
[email protected]
maintainerThe patch below does not apply to the 6.1-stable tree.
If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <[email protected]>.
To reproduce the conflict and resubmit, you may use the following commands:
git fetch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ linux-6.1.y
git checkout FETCH_HEAD
git cherry-pick -x 51f89c488f2ecc020f82bfedd77482584ce8027a
# <resolve conflicts, build, test, etc.>
git commit -s
git send-email --to '<[email protected]>' --in-reply-to '2026010552-unmoved-tipoff-f490@gregkh' --subject-prefix 'PATCH 6.1.y' HEAD^..
Possible dependencies:
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
From 51f89c488f2ecc020f82bfedd77482584ce8027a Mon Sep 17 00:00:00 2001
From: Siddharth Vadapalli <[email protected]>
Date: Wed, 19 Nov 2025 21:31:05 +0530
Subject: [PATCH] arm64: dts: ti: k3-j721e-sk: Fix pinmux for pin Y1 used by
power regulator
The SoC pin Y1 is incorrectly defined in the WKUP Pinmux device-tree node (pinctrl@4301c000) leading to the following silent failure:
pinctrl-single 4301c000.pinctrl: mux offset out of range: 0x1dc (0x178)
According to the datasheet for the J721E SoC [0], the pin Y1 belongs to the MAIN Pinmux device-tree node (pinctrl@11c000). This is confirmed by the address of the pinmux register for it on page 142 of the datasheet which is 0x00011C1DC.
Hence fix it.
[0]: https://www.ti.com/lit/ds/symlink/tda4vm.pdf
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +6 -6
@@ -474,6 +474,12 @@ rpi_header_gpio1_pins_default: rpi-header-gpio1-default-pins { J721E_IOPAD(0x234, PIN_INPUT, 7) /* (U3) EXT_REFCLK1.GPIO1_12 */ >; }; + + vdd_sd_dv_pins_default: vdd-sd-dv-default-pins { + pinctrl-single,pins = < + J721E_IOPAD(0x1dc, PIN_OUTPUT, 7) /* (Y1) SPI1_CLK.GPIO0_118 */ + >; + }; }; &wkup_pmx0 {
@@ -536,12 +542,6 @@ J721E_WKUP_IOPAD(0xd4, PIN_OUTPUT, 7) /* (G26) WKUP_GPIO0_9 */ >; }; - vdd_sd_dv_pins_default: vdd-sd-dv-default-pins { - pinctrl-single,pins = < - J721E_IOPAD(0x1dc, PIN_OUTPUT, 7) /* (Y1) SPI1_CLK.GPIO0_118 */ - >; - }; - wkup_uart0_pins_default: wkup-uart0-default-pins { pinctrl-single,pins = < J721E_WKUP_IOPAD(0xa0, PIN_INPUT, 0) /* (J29) WKUP_UART0_RXD */
Sasha Levin
maintainerPATCH 1/1 arm64: dts: ti: k3-j721e-sk: Fix pinmux for pin Y1 used by power regulator
From: Siddharth Vadapalli <[email protected]>
[ Upstream commit 51f89c488f2ecc020f82bfedd77482584ce8027a ]
The SoC pin Y1 is incorrectly defined in the WKUP Pinmux device-tree node (pinctrl@4301c000) leading to the following silent failure:
pinctrl-single 4301c000.pinctrl: mux offset out of range: 0x1dc (0x178)
According to the datasheet for the J721E SoC [0], the pin Y1 belongs to the MAIN Pinmux device-tree node (pinctrl@11c000). This is confirmed by the address of the pinmux register for it on page 142 of the datasheet which is 0x00011C1DC.
Hence fix it.
[0]: https://www.ti.com/lit/ds/symlink/tda4vm.pdf
--- arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)
arch/arm64/boot/dts/ti/k3-j721e-sk.dts +6 -6
@@ -425,6 +425,12 @@ ekey_reset_pins_default: ekey-reset-pns-pins-default { J721E_IOPAD(0x124, PIN_INPUT, 7) /* (Y24) PRG0_PRU1_GPO9.GPIO0_72 */ >; }; + + vdd_sd_dv_pins_default: vdd-sd-dv-default-pins { + pinctrl-single,pins = < + J721E_IOPAD(0x1dc, PIN_OUTPUT, 7) /* (Y1) SPI1_CLK.GPIO0_118 */ + >; + }; }; &wkup_pmx0 {
@@ -480,12 +486,6 @@ J721E_WKUP_IOPAD(0xd4, PIN_OUTPUT, 7) /* (G26) WKUP_GPIO0_9 */ >; }; - vdd_sd_dv_pins_default: vdd-sd-dv-default-pins { - pinctrl-single,pins = < - J721E_IOPAD(0x1dc, PIN_OUTPUT, 7) /* (Y1) SPI1_CLK.GPIO0_118 */ - >; - }; - wkup_i2c0_pins_default: wkup-i2c0-pins-default { pinctrl-single,pins = < J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
Signature · 1 line
2.51.0