arm64: dts: marvell: Fix stray and typo "pinctrl-names" properties
Subsystems (2)
Rob Herring (Arm)
maintainerPATCH 1/1 arm64: dts: marvell: Fix stray and typo "pinctrl-names" properties
There's several cases of "pinctrl-names" used without any "pinctrl-0" properties. Drop them.
Fix the typo "pintrl-names" as well.
Signed-off-by Rob Herring (Arm) <[email protected]>
--- arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts | 1 - arch/arm64/boot/dts/marvell/cn9130-cf-base.dts | 2 +- arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 1 - arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 2 -- arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 1 - 5 files changed, 1 insertion(+), 6 deletions(-)
arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts +0 -1
@@ -42,7 +42,6 @@ usb3_phy: usb3-phy { }; gpio-leds { - pinctrl-names = "default"; compatible = "gpio-leds"; /* No assigned functions to the LEDs by default */ led1 {
arch/arm64/boot/dts/marvell/cn9130-cf-base.dts +1 -1
@@ -137,7 +137,7 @@ led@1 { &cp0_pinctrl { pinctrl-0 = <&sim_select_pins>; - pintrl-names = "default"; + pinctrl-names = "default"; rear_button_pins: cp0-rear-button-pins { marvell,pins = "mpp31";
arch/arm64/boot/dts/marvell/cn9130-crb.dtsi +0 -1
@@ -93,7 +93,6 @@ &uart0 { /* on-board eMMC U6 */ &ap_sdhci0 { - pinctrl-names = "default"; bus-width = <8>; status = "okay"; mmc-ddr-1_8v;
arch/arm64/boot/dts/marvell/cn9130-db.dtsi +0 -2
@@ -111,7 +111,6 @@ &uart0 { /* on-board eMMC - U9 */ &ap_sdhci0 { - pinctrl-names = "default"; bus-width = <8>; vqmmc-supply = <&ap0_reg_sd_vccq>; status = "okay";
@@ -166,7 +165,6 @@ &cp0_i2c0 { /* U36 */ expander0: pca953x@21 { compatible = "nxp,pca9555"; - pinctrl-names = "default"; gpio-controller; #gpio-cells = <2>; reg = <0x21>;
arch/arm64/boot/dts/marvell/cn9132-db.dtsi +0 -1
@@ -142,7 +142,6 @@ i2c@1 { /* U12 */ cp2_module_expander1: pca9555@21 { compatible = "nxp,pca9555"; - pinctrl-names = "default"; gpio-controller; #gpio-cells = <2>; reg = <0x21>;
Signature · 1 line
2.51.0
Gregory CLEMENT
maintainerQuoted 6 lines · Rob Herring (Arm)
There's several cases of "pinctrl-names" used without any "pinctrl-0" properties. Drop them.
Fix the typo "pintrl-names" as well.
Signed-off-by Rob Herring (Arm) <[email protected]>
Applied on mvebu/dt64
Thanks,
Gregory
Quoted 80 lines
--- arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts | 1 - arch/arm64/boot/dts/marvell/cn9130-cf-base.dts | 2 +- arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 1 - arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 2 -- arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 1 - 5 files changed, 1 insertion(+), 6 deletions(-)arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts +0
-1@@ -42,7 +42,6 @@ usb3_phy: usb3-phy { }; gpio-leds { - pinctrl-names = "default"; compatible = "gpio-leds"; /* No assigned functions to the LEDs by default */ led1 {arch/arm64/boot/dts/marvell/cn9130-cf-base.dts +1
-1@@ -137,7 +137,7 @@ led@1 { &cp0_pinctrl { pinctrl-0 = <&sim_select_pins>; - pintrl-names = "default"; + pinctrl-names = "default"; rear_button_pins: cp0-rear-button-pins { marvell,pins = "mpp31";arch/arm64/boot/dts/marvell/cn9130-crb.dtsi +0
-1@@ -93,7 +93,6 @@ &uart0 { /* on-board eMMC U6 */ &ap_sdhci0 { - pinctrl-names = "default"; bus-width = <8>; status = "okay"; mmc-ddr-1_8v;arch/arm64/boot/dts/marvell/cn9130-db.dtsi +0
-2@@ -111,7 +111,6 @@ &uart0 { /* on-board eMMC - U9 */ &ap_sdhci0 { - pinctrl-names = "default"; bus-width = <8>; vqmmc-supply = <&ap0_reg_sd_vccq>; status = "okay";@@ -166,7 +165,6 @@ &cp0_i2c0 { /* U36 */ expander0: pca953x@21 { compatible = "nxp,pca9555"; - pinctrl-names = "default"; gpio-controller; #gpio-cells = <2>; reg = <0x21>;arch/arm64/boot/dts/marvell/cn9132-db.dtsi +0
-1@@ -142,7 +142,6 @@ i2c@1 { /* U12 */ cp2_module_expander1: pca9555@21 { compatible = "nxp,pca9555"; - pinctrl-names = "default"; gpio-controller; #gpio-cells = <2>; reg = <0x21>;Signature · 1 line
2.51.0
Signature · 3 lines
Grégory CLEMENT, Bootlin Embedded Linux and Kernel engineering https://bootlin.com