Add Qualcomm Technologies, Inc. Talos EVK SMARC support
v11 cover Add Qualcomm Technologies, Inc. Talos EVK SMARC support
Hi all,
This patch series adds device tree binding and board support for the Qualcomm Technologies, Inc. Talos EVK SMARC platform based on the QCS615 SoC.
The first patch introduces the DT binding entry for the Talos EVK SMARC board, and the second patch adds the corresponding DTS files for the platform.
Note:USB(usb_1_dwc3) supports host-only mode based on the switch SW1 on the SoM, which is purely a hardware controlled as USB-ID and USB-VBUS is not connected the switching cannot be handled from SW. Hence from SW Host-only mode is supported on Linux boot up.
Changes in v11:
- Fixed inconsistent USB PHY node naming in qcs615-ride.dts to align with the expected naming convention. (suggested by yuanjiey)
- Reordered properties in property-n and property-names for consistency across DT files.
- Removed unnecessary output-low from the bt_en_state node.
- Used a &label_reference for hdmi_connector.
- Added pcieport0 device node, which is required for WLAN to power on.
- No functional change in bindings file.
Changes in v10:
- This series extends the gpio-backlight driver and its DT bindings to support multiple control GPIOs. (suggested by Dmitry)
- Addressed DT node labeling feedback.
- Polished overall device tree structure and minor formattings.
- Corrected pinctrl configuration for the active-low PERST# pin.
- Includes a fix for inconsistent USB PHY node naming in talos.dtsi. (suggested by Dmitry)
- Enabled WiFi and Bluetooth functionality.
- Updated commit message.
- No functional change in bindings file.
Changes in v9:
- The updates in the following patch url is taken care in this patch series.
https://lists.freedesktop.org/archives/dri-devel/2025-November/534473.html
- Ignore v8 patch
Changes in v8:
- This patch series depends on the below url
https://lists.freedesktop.org/archives/dri-devel/2025-November/534473.html
- Moved the contents of talos-evk-cb.dtsi to talos-evk.dtsi which will describe all the standard configuration of the EVK.
- Introduced 'talos-evk-lvds-auo,g133han01.dtso' which has overlay to disable HDMI and adds the LVDS-related on top of the base dts file. (suggested by Bjorn)
- Ethernet and Wi-Fi/BT are not (yet) supported.
- Updated commit message.
- No functional change in bindings file.
Changes in v7:
- Added i2c clock frequency for i2c5 node.
- Moved adv7535 controller section to talos-evk.dts file.
- Reorder the usb nodes.
- GPI_DMA nodes added in the device tree files.
- No functional change in bindings file.
Changes in v6:
- Clarified description of talos-evk-cb.dtsi to explain that it defines common carrier board interfaces shared between HDMI and LVDS variants, And It’s a single carrier board. HDMI and LVDS share the same DSI interface, and only one can be active at a time depending on a DIP switch.
- Added missing newlines before 'status' and between the last property and subnode (suggested by Konrad).
- Updated commit messages for clarity.
Changes in v5:
- Updated commit message. (suggested by Krzysztof)
- Introduced generic node name for can, dp, hdmi-bridge. (suggested by Krzysztof)
- Introduced talos-evk-cb.dtsi, which has common carrier board interfaces.
- No functional change in bindings file.
Changes in v4:
- Updated product name to full form per Krzysztof’s feedback in dt-binding comment.
- Hook up the ADV7535 DSI-to-HDMI bridge to base DTS file.
- Add DP connector node and MDSS DisplayPort controller.
- Added USB note in the cover letter for maintainers' awareness.
Changes in v3:
- Addressed comments from Dmitry regarding USB1 dr_mode and added a DTS comment.
- No functional change in bindings file.
Changes in v2:
- Renamed compatible to "qcom,talos-evk" (suggested by Dmitry/Bjorn)
- Merged enum entry with existing qcs615-ride block (Krzysztof)
- Fixed subject and commit message to use imperative mood.
Thanks,
Anusha
Sudarshan Shetty (4):
dt-bindings: arm: qcom: talos-evk: Add QCS615 Talos EVK SMARC platform
arm64: dts: qcom: talos: Fix inconsistent USB PHY node naming
arm64: dts: qcom: qcs615-ride: Fix USB PHY label reference
arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board
.../devicetree/bindings/arm/qcom.yaml | 1 + arch/arm64/boot/dts/qcom/Makefile | 4 + arch/arm64/boot/dts/qcom/qcs615-ride.dts | 2 +- .../qcom/talos-evk-lvds-auo,g133han01.dtso | 126 ++++ arch/arm64/boot/dts/qcom/talos-evk-som.dtsi | 616 ++++++++++++++++++ arch/arm64/boot/dts/qcom/talos-evk.dts | 139 ++++ arch/arm64/boot/dts/qcom/talos.dtsi | 4 +- 7 files changed, 889 insertions(+), 3 deletions(-) create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-som.dtsi create mode 100644 arch/arm64/boot/dts/qcom/talos-evk.dts
Signature · 1 line
2.34.1
PATCH v11 1/4 dt-bindings: arm: qcom: talos-evk: Add QCS615 Talos EVK SMARC platform
Add binding support for the Qualcomm Technologies, Inc. Talos EVK SMARC platform based on the QCS615 SoC.
--- Documentation/devicetree/bindings/arm/qcom.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/qcom.yaml +1 -0
@@ -876,6 +876,7 @@ properties: - items: - enum: - qcom,qcs615-ride + - qcom,talos-evk - const: qcom,qcs615 - const: qcom,sm6150
Signature · 1 line
2.34.1
PATCH v11 2/4 arm64: dts: qcom: talos: Fix inconsistent USB PHY node naming
In reply to Sudarshan ShettyThe USB PHY nodes has inconsistent labels as 'usb_1_hspy' and 'usb_hsphy_2'. This patch renames them to follow a consistent naming scheme.
No functional changes, only label renaming.
--- arch/arm64/boot/dts/qcom/talos.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm64/boot/dts/qcom/talos.dtsi +2 -2
@@ -4304,7 +4304,7 @@ osm_l3: interconnect@18321000 { #interconnect-cells = <1>; }; - usb_1_hsphy: phy@88e2000 { + usb_hsphy_1: phy@88e2000 { compatible = "qcom,qcs615-qusb2-phy"; reg = <0x0 0x88e2000 0x0 0x180>;
@@ -4412,7 +4412,7 @@ usb_1_dwc3: usb@a600000 { iommus = <&apps_smmu 0x140 0x0>; interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; - phys = <&usb_1_hsphy>, <&usb_qmpphy>; + phys = <&usb_hsphy_1>, <&usb_qmpphy>; phy-names = "usb2-phy", "usb3-phy"; snps,dis-u1-entry-quirk;
Signature · 1 line
2.34.1
PATCH v11 3/4 arm64: dts: qcom: qcs615-ride: Fix USB PHY label reference
In reply to Sudarshan ShettyUpdate the USB high-speed PHY label from 'usb_1_hsphy' to 'usb_hsphy_1' to maintain consistency with the naming convention used in talos.dtsi, where the second PHY is labeled 'usb_hsphy_2'.
No functional changes, only label renaming.
--- arch/arm64/boot/dts/qcom/qcs615-ride.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/qcom/qcs615-ride.dts +1 -1
@@ -609,7 +609,7 @@ bluetooth { }; }; -&usb_1_hsphy { +&usb_hsphy_1 { vdd-supply = <&vreg_l5a>; vdda-pll-supply = <&vreg_l12a>; vdda-phy-dpdm-supply = <&vreg_l13a>;
Signature · 1 line
2.34.1
Re: [PATCH v11 3/4] arm64: dts: qcom: qcs615-ride: Fix USB PHY label reference
Quoted 17 lines · Sudarshan Shetty
Update the USB high-speed PHY label from '
usb_1_hsphy' to 'usb_hsphy_1' to maintain consistency with the naming convention used intalos.dtsi, where the second PHY is labeled 'usb_hsphy_2'.No functional changes, only label renaming.
Signed-off-by Sudarshan Shetty <[email protected]>--- arch/arm64/boot/dts/qcom/qcs615-ride.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)arch/arm64/boot/dts/qcom/qcs615-ride.dts +0
-0
arch/arm64/boot/dts/qcom/qcs615-ride.dts bluetooth { · line 615
Quoted 8 lines
arch/arm64/boot/dts/qcom/qcs615-ride.dts +1
-1@@ -609,7 +609,7 @@ bluetooth { }; }; -&usb_1_hsphy { +&usb_hsphy_1 { vdd-supply = <&vreg_l5a>; vdda-pll-supply = <&vreg_l12a>; vdda-phy-dpdm-supply = <&vreg_l13a>;
This must be squashed with patch 2, otherwise patch 2 is going to cause a build failure which must not happen at any point in the git history (to make bisecting possible)
Konrad
Re: [PATCH v11 3/4] arm64: dts: qcom: qcs615-ride: Fix USB PHY label reference
Quoted 21 lines · Konrad Dybcio
Quoted 20 lines · Sudarshan Shetty
Update the USB high-speed PHY label from '
usb_1_hsphy' to 'usb_hsphy_1' to maintain consistency with the naming convention used intalos.dtsi, where the second PHY is labeled 'usb_hsphy_2'.No functional changes, only label renaming.
Signed-off-by Sudarshan Shetty <[email protected]>--- arch/arm64/boot/dts/qcom/qcs615-ride.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)arch/arm64/boot/dts/qcom/qcs615-ride.dts +0
-0@@ -609,7 +609,7 @@ bluetooth { }; };
Quoted 10 lines
arch/arm64/boot/dts/qcom/qcs615-ride.dts bluetooth { · line 615
Quoted 5 lines
arch/arm64/boot/dts/qcom/qcs615-ride.dts +1
-1-&usb_1_hsphy { +&usb_hsphy_1 { vdd-supply = <&vreg_l5a>; vdda-pll-supply = <&vreg_l12a>; vdda-phy-dpdm-supply = <&vreg_l13a>;This must be squashed with patch 2, otherwise patch 2 is going to cause a build failure which must not happen at any point in the git history (to make bisecting possible)
Okay, I will squash these changes with patch 2 in the next patch series.
Quoted 1 line
Konrad
PATCH v11 4/4 arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board
In reply to Sudarshan ShettyAdd the device tree for the QCS615-based Talos EVK platform. The platform is composed of a System-on-Module following the SMARC standard, and a Carrier Board.
The Carrier Board supports several display configurations, HDMI and LVDS. Both configurations use the same base hardware, with the display selection controlled by a DIP switch.
Use a DTBO file, talos-evk-lvds-auo,g133han01.dtso, which defines an overlay that disables HDMI and adds LVDS. The DTs file talos-evk can describe the HDMI display configurations.
The initial device tree includes support for:
- CPU and memory
- UART
- GPIOs
- Regulators
- PMIC
- Early console
- AT24MAC602 EEPROM
- MCP2515 SPI to CAN
- ADV7535 DSI-to-HDMI bridge
- DisplayPort interface
- SN65DSI84ZXHR DSI-to-LVDS bridge
- Wi-Fi/BT
--- arch/arm64/boot/dts/qcom/Makefile | 4 + .../qcom/talos-evk-lvds-auo,g133han01.dtso | 126 ++++ arch/arm64/boot/dts/qcom/talos-evk-som.dtsi | 616 ++++++++++++++++++ arch/arm64/boot/dts/qcom/talos-evk.dts | 139 ++++ 4 files changed, 885 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-som.dtsi create mode 100644 arch/arm64/boot/dts/qcom/talos-evk.dts
arch/arm64/boot/dts/qcom/Makefile +4 -0
@@ -324,6 +324,10 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8750-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8750-qrd.dtb +dtb-$(CONFIG_ARCH_QCOM) += talos-evk.dtb +talos-evk-lvds-auo,g133han01-dtbs := \ + talos-evk.dtb talos-evk-lvds-auo,g133han01.dtbo +dtb-$(CONFIG_ARCH_QCOM) += talos-evk-lvds-auo,g133han01.dtb x1e001de-devkit-el2-dtbs := x1e001de-devkit.dtb x1-el2.dtbo dtb-$(CONFIG_ARCH_QCOM) += x1e001de-devkit.dtb x1e001de-devkit-el2.dtb x1e78100-lenovo-thinkpad-t14s-el2-dtbs := x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso new file +126 -0
126 lines not on this page · raw message
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +616 -0
616 lines not on this page · raw message
arch/arm64/boot/dts/qcom/talos-evk.dts new file +139 -0
139 lines not on this page · raw message
Signature · 1 line
2.34.1
Re: [PATCH v11 4/4] arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board
Quoted 110 lines · Sudarshan Shetty
Add the device tree for the QCS615-based Talos EVK platform. The platform is composed of a System-on-Module following the SMARC standard, and a Carrier Board.
The Carrier Board supports several display configurations, HDMI and LVDS. Both configurations use the same base hardware, with the display selection controlled by a DIP switch.
Use a DTBO file, talos-evk-lvds-auo,g133han01.dtso, which defines an overlay that disables HDMI and adds LVDS. The DTs file talos-evk can describe the HDMI display configurations.
The initial device tree includes support for:
- CPU and memory
- UART
- GPIOs
- Regulators
- PMIC
- Early console
- AT24MAC602 EEPROM
- MCP2515 SPI to CAN
- ADV7535 DSI-to-HDMI bridge
- DisplayPort interface
- SN65DSI84ZXHR DSI-to-LVDS bridge
- Wi-Fi/BTReviewed-by Dmitry Baryshkov <[email protected]>Signed-off-by Sudarshan Shetty <[email protected]>--- arch/arm64/boot/dts/qcom/Makefile | 4 + .../qcom/talos-evk-lvds-auo,g133han01.dtso | 126 ++++ arch/arm64/boot/dts/qcom/talos-evk-som.dtsi | 616 ++++++++++++++++++ arch/arm64/boot/dts/qcom/talos-evk.dts | 139 ++++ 4 files changed, 885 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-som.dtsi create mode 100644 arch/arm64/boot/dts/qcom/talos-evk.dtsarch/arm64/boot/dts/qcom/Makefile +4
-0@@ -324,6 +324,10 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8750-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8750-qrd.dtb +dtb-$(CONFIG_ARCH_QCOM) += talos-evk.dtb +talos-evk-lvds-auo,g133han01-dtbs := \ + talos-evk.dtb talos-evk-lvds-auo,g133han01.dtbo +dtb-$(CONFIG_ARCH_QCOM) += talos-evk-lvds-auo,g133han01.dtb x1e001de-devkit-el2-dtbs := x1e001de-devkit.dtb x1-el2.dtbo dtb-$(CONFIG_ARCH_QCOM) += x1e001de-devkit.dtb x1e001de-devkit-el2.dtb x1e78100-lenovo-thinkpad-t14s-el2-dtbs := x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtboarch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso new file +51
-0@@ -0,0 +1,126 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; +/plugin/; + +#include <dt-bindings/gpio/gpio.h> + +&{/} { + backlight: backlight { + compatible = "gpio-backlight"; + gpios = <&tlmm 59 GPIO_ACTIVE_HIGH>, + <&tlmm 115 GPIO_ACTIVE_HIGH>; + default-on; + }; + + panel-lvds { + compatible = "auo,g133han01"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* LVDS A (Odd pixels) */ + port@0 { + reg = <0>; + dual-lvds-odd-pixels; + + lvds_panel_out_a: endpoint { + remote-endpoint = <&sn65dsi84_out_a>; + }; + }; + + /* LVDS B (Even pixels) */ + port@1 { + reg = <1>; + dual-lvds-even-pixels; + + lvds_panel_out_b: endpoint { + remote-endpoint = <&sn65dsi84_out_b>; + }; + }; + }; + }; +}; + +&hdmi_connector { + status = "disabled"; +}; +
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso line 61
Quoted 10 lines
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso new file +10
-0+&i2c1 { + clock-frequency = <400000>; + + status = "okay"; + + hdmi_bridge: bridge@3d { + status = "disabled"; + }; + + lvds_bridge: bridge@2c {
power-supply, if be optional, need to modify dt-binding file. otherwise we will meet binding check error.
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso line 67
Quoted 6 lines
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso new file +6
-0+ compatible = "ti,sn65dsi84"; + reg = <0x2c>; + enable-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; + ti,dsi-lanes = <4>; + ti,lvds-format = "jeida-24"; + ti,lvds-bpp = <24>;
ti,dsi-lanes, ti,lvds-format, ti,lvds-bpp, do we need these property? I don't see these property be used from kernel 6.6 to kernel 6.19.
Thanks,
Yuanjie
Quoted 827 lines
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso new file +58
-0+ ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + sn65dsi84_in: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@2 { + reg = <2>; + + sn65dsi84_out_a: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_a>; + }; + }; + + port@3 { + reg = <3>; + + sn65dsi84_out_b: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_b>; + }; + }; + }; + }; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l11a>; + + status = "okay"; +}; + +&mdss_dsi0_out { + remote-endpoint = <&sn65dsi84_in>; + data-lanes = <0 1 2 3>; +}; + +&tlmm { + lcd_bklt_en: lcd-bklt-en-state { + pins = "gpio115"; + function = "gpio"; + bias-disable; + }; + + lcd_bklt_pwm: lcd-bklt-pwm-state { + pins = "gpio59"; + function = "gpio"; + bias-disable; + }; +};arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +616
-0@@ -0,0 +1,616 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "talos.dtsi" +#include "pm8150.dtsi" +/ { + aliases { + mmc0 = &sdhc_1; + serial0 = &uart0; + serial1 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + clocks { + can_osc: can-oscillator { + compatible = "fixed-clock"; + clock-frequency = <20000000>; + #clock-cells = <0>; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32764>; + #clock-cells = <0>; + }; + + xo_board_clk: xo-board-clk { + compatible = "fixed-clock"; + clock-frequency = <38400000>; + #clock-cells = <0>; + }; + }; + + regulator-usb2-vbus { + compatible = "regulator-fixed"; + regulator-name = "USB2_VBUS"; + gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&usb2_en>; + pinctrl-names = "default"; + enable-active-high; + regulator-always-on; + }; + + vreg_conn_1p8: regulator-conn-1p8 { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_1p8"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 1 GPIO_ACTIVE_HIGH>; + }; + + vreg_conn_pa: regulator-conn-pa { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_pa"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 6 GPIO_ACTIVE_HIGH>; + }; + + vreg_v3p3_can: regulator-v3p3-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v3p3-can"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v5p0_can: regulator-v5p0-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v5p0-can"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + wcn6855-pmu { + compatible = "qcom,wcn6855-pmu"; + + pinctrl-0 = <&bt_en_state>, <&wlan_en_state>; + pinctrl-names = "default"; + + bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; + wlan-enable-gpios = <&tlmm 84 GPIO_ACTIVE_HIGH>; + + vddio-supply = <&vreg_conn_pa>; + vddaon-supply = <&vreg_s5a>; + vddpmu-supply = <&vreg_conn_1p8>; + vddpmumx-supply = <&vreg_conn_1p8>; + vddpmucx-supply = <&vreg_conn_pa>; + vddrfa0p95-supply = <&vreg_s5a>; + vddrfa1p3-supply = <&vreg_s6a>; + vddrfa1p9-supply = <&vreg_l15a>; + vddpcie1p3-supply = <&vreg_s6a>; + vddpcie1p9-supply = <&vreg_l15a>; + + regulators { + vreg_pmu_rfa_cmn: ldo0 { + regulator-name = "vreg_pmu_rfa_cmn"; + }; + + vreg_pmu_aon_0p59: ldo1 { + regulator-name = "vreg_pmu_aon_0p59"; + }; + + vreg_pmu_wlcx_0p8: ldo2 { + regulator-name = "vreg_pmu_wlcx_0p8"; + }; + + vreg_pmu_wlmx_0p85: ldo3 { + regulator-name = "vreg_pmu_wlmx_0p85"; + }; + + vreg_pmu_btcmx_0p85: ldo4 { + regulator-name = "vreg_pmu_btcmx_0p85"; + }; + + vreg_pmu_rfa_0p8: ldo5 { + regulator-name = "vreg_pmu_rfa_0p8"; + }; + + vreg_pmu_rfa_1p2: ldo6 { + regulator-name = "vreg_pmu_rfa_1p2"; + }; + + vreg_pmu_rfa_1p7: ldo7 { + regulator-name = "vreg_pmu_rfa_1p7"; + }; + + vreg_pmu_pcie_0p9: ldo8 { + regulator-name = "vreg_pmu_pcie_0p9"; + }; + + vreg_pmu_pcie_1p8: ldo9 { + regulator-name = "vreg_pmu_pcie_1p8"; + }; + }; + }; + + wifi_1p8v: regulator-wifi-1p8v { + compatible = "regulator-fixed"; + regulator-name = "wifi_1p8v"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; + + wifi_3p85v: regulator-wifi-3p85v { + compatible = "regulator-fixed"; + regulator-name = "wifi_3p85v"; + regulator-min-microvolt = <3850000>; + regulator-max-microvolt = <3850000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8150-rpmh-regulators"; + qcom,pmic-id = "a"; + + vreg_s3a: smps3 { + regulator-name = "vreg_s3a"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <650000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s4a: smps4 { + regulator-name = "vreg_s4a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1829000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s5a: smps5 { + regulator-name = "vreg_s5a"; + regulator-min-microvolt = <1896000>; + regulator-max-microvolt = <2040000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s6a: smps6 { + regulator-name = "vreg_s6a"; + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1404000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1a: ldo1 { + regulator-name = "vreg_l1a"; + regulator-min-microvolt = <488000>; + regulator-max-microvolt = <852000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2a: ldo2 { + regulator-name = "vreg_l2a"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3a: ldo3 { + regulator-name = "vreg_l3a"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1248000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5a: ldo5 { + regulator-name = "vreg_l5a"; + regulator-min-microvolt = <875000>; + regulator-max-microvolt = <975000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7a: ldo7 { + regulator-name = "vreg_l7a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1900000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8a: ldo8 { + regulator-name = "vreg_l8a"; + regulator-min-microvolt = <1150000>; + regulator-max-microvolt = <1350000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10a: ldo10 { + regulator-name = "vreg_l10a"; + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11a: ldo11 { + regulator-name = "vreg_l11a"; + regulator-min-microvolt = <1232000>; + regulator-max-microvolt = <1260000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12a: ldo12 { + regulator-name = "vreg_l12a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1890000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13a: ldo13 { + regulator-name = "vreg_l13a"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3230000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15a: ldo15 { + regulator-name = "vreg_l15a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1904000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l16a: ldo16 { + regulator-name = "vreg_l16a"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17a: ldo17 { + regulator-name = "vreg_l17a"; + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&gpi_dma0 { + status = "okay"; +}; + +&gpi_dma1 { + status = "okay"; +}; + +&i2c5 { + clock-frequency = <400000>; + status = "okay"; + + eeprom@57 { + compatible = "atmel,24c02"; + reg = <0x57>; + pagesize = <16>; + }; + + eeprom@5f { + compatible = "atmel,24mac602"; + reg = <0x5f>; + pagesize = <16>; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dp0 { + status = "okay"; +}; + +&mdss_dp0_out { + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000>; + remote-endpoint = <&dp0_connector_in>; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l11a>; + status = "okay"; +}; + +&mdss_dsi0_phy { + vcca-supply = <&vreg_l5a>; + status = "okay"; +}; + +&pcie { + perst-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&pcie_default_state>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie_phy { + vdda-phy-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + + status = "okay"; +}; + +&pcie_port0 { + wifi@0 { + compatible = "pci17cb,1103"; + reg = <0x10000 0x0 0x0 0x0 0x0>; + + qcom,calibration-variant = "QC_QCS615_Ride"; + + vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; + vddaon-supply = <&vreg_pmu_aon_0p59>; + vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; + vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; + vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>; + vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>; + vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>; + }; +}; + +&pm8150_gpios { + usb2_en: usb2-en-state { + pins = "gpio10"; + function = "normal"; + output-enable; + power-source = <0>; + }; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/qcs615/adsp.mbn"; + + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/qcs615/cdsp.mbn"; + + status = "okay"; +}; + +&sdhc_1 { + pinctrl-0 = <&sdc1_state_on>; + pinctrl-1 = <&sdc1_state_off>; + pinctrl-names = "default", "sleep"; + + bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + vmmc-supply = <&vreg_l17a>; + vqmmc-supply = <&vreg_s4a>; + + non-removable; + no-sd; + no-sdio; + + status = "okay"; +}; + +&spi6 { + status = "okay"; + + can@0 { + compatible = "microchip,mcp2515"; + reg = <0>; + clocks = <&can_osc>; + interrupts-extended = <&tlmm 87 IRQ_TYPE_LEVEL_LOW>; + spi-max-frequency = <10000000>; + vdd-supply = <&vreg_v3p3_can>; + xceiver-supply = <&vreg_v5p0_can>; + }; +}; + +&tlmm { + bt_en_state: bt-en-state { + pins = "gpio85"; + function = "gpio"; + bias-pull-down; + }; + + pcie_default_state: pcie-default-state { + clkreq-pins { + pins = "gpio90"; + function = "pcie_clk_req"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-pins { + pins = "gpio89"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-pins { + pins = "gpio100"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + wifi_reg_en_pins_state: wifi-reg-en-pins-state { + pins = "gpio91"; + function = "gpio"; + drive-strength = <8>; + output-high; + bias-pull-up; + }; + + wlan_en_state: wlan-en-state { + pins = "gpio84"; + function = "gpio"; + drive-strength = <16>; + bias-pull-down; + output-low; + }; +}; + +&uart0 { + status = "okay"; +}; + +&uart7 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn6855-bt"; + firmware-name = "QCA6698/hpnv21", "QCA6698/hpbtfw21.tlv"; + + vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; + vddaon-supply = <&vreg_pmu_aon_0p59>; + vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; + vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; + vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>; + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; + vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>; + }; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "host"; +}; + +&usb_hsphy_1 { + vdd-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + vdda-phy-dpdm-supply = <&vreg_l13a>; + + status = "okay"; +}; + +&usb_2 { + status = "okay"; +}; + +&usb_2_dwc3 { + dr_mode = "host"; +}; + +&usb_hsphy_2 { + vdd-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + vdda-phy-dpdm-supply = <&vreg_l13a>; + + status = "okay"; +}; + +&usb_qmpphy { + vdda-phy-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + + status = "okay"; +}; + +&usb_qmpphy_2 { + vdda-phy-supply = <&vreg_l11a>; + vdda-pll-supply = <&vreg_l5a>; + + status = "okay"; +}; + +&ufs_mem_hc { + reset-gpios = <&tlmm 123 GPIO_ACTIVE_LOW>; + vcc-supply = <&vreg_l17a>; + vcc-max-microamp = <600000>; + vccq2-supply = <&vreg_s4a>; + vccq2-max-microamp = <600000>; + + status = "okay"; +}; + +&ufs_mem_phy { + vdda-phy-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + + status = "okay"; +}; + +&venus { + status = "okay"; +};arch/arm64/boot/dts/qcom/talos-evk.dts new file +139
-0@@ -0,0 +1,139 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; + +#include "talos-evk-som.dtsi" + +/ { + model = "Qualcomm QCS615 IQ 615 EVK"; + compatible = "qcom,talos-evk", "qcom,qcs615", "qcom,sm6150"; + chassis-type = "embedded"; + + aliases { + mmc1 = &sdhc_2; + }; + + dp0-connector { + compatible = "dp-connector"; + label = "DP0"; + type = "full-size"; + + hpd-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>; + + port { + dp0_connector_in: endpoint { + remote-endpoint = <&mdss_dp0_out>; + }; + }; + }; + + hdmi_connector: hdmi-out { + compatible = "hdmi-connector"; + type = "d"; + + port { + hdmi_con_out: endpoint { + remote-endpoint = <&adv7535_out>; + }; + }; + }; + + vreg_v1p8_out: regulator-v1p8-out { + compatible = "regulator-fixed"; + regulator-name = "vreg-v1p8-out"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vreg_v5p0_out>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v3p3_out: regulator-v3p3-out { + compatible = "regulator-fixed"; + regulator-name = "vreg-v3p3-out"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vreg_v5p0_out>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v5p0_out: regulator-v5p0-out { + compatible = "regulator-fixed"; + regulator-name = "vreg-v5p0-out"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + /* Powered by system 20V rail (USBC_VBUS_IN) */ + }; +}; + +&i2c1 { + clock-frequency = <400000>; + status = "okay"; + + hdmi_bridge: bridge@3d { + compatible = "adi,adv7535"; + reg = <0x3d>; + avdd-supply = <&vreg_v1p8_out>; + dvdd-supply = <&vreg_v1p8_out>; + pvdd-supply = <&vreg_v1p8_out>; + a2vdd-supply = <&vreg_v1p8_out>; + v3p3-supply = <&vreg_v3p3_out>; + interrupts-extended = <&tlmm 26 IRQ_TYPE_LEVEL_LOW>; + adi,dsi-lanes = <4>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + adv7535_in: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + + adv7535_out: endpoint { + remote-endpoint = <&hdmi_con_out>; + }; + }; + }; + }; +}; + +&mdss_dsi0_out { + remote-endpoint = <&adv7535_in>; + data-lanes = <0 1 2 3>; +}; + +&pon_pwrkey { + status = "okay"; +}; + +&pon_resin { + linux,code = <KEY_VOLUMEDOWN>; + + status = "okay"; +}; + +&sdhc_2 { + pinctrl-0 = <&sdc2_state_on>; + pinctrl-1 = <&sdc2_state_off>; + pinctrl-names = "default", "sleep"; + + bus-width = <4>; + cd-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>; + + vmmc-supply = <&vreg_l10a>; + vqmmc-supply = <&vreg_s4a>; + + status = "okay"; +};Signature · 1 line
2.34.1
Re: [PATCH v11 4/4] arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board
Quoted 115 lines · yuanjiey
Quoted 114 lines · Sudarshan Shetty
Add the device tree for the QCS615-based Talos EVK platform. The platform is composed of a System-on-Module following the SMARC standard, and a Carrier Board.
The Carrier Board supports several display configurations, HDMI and LVDS. Both configurations use the same base hardware, with the display selection controlled by a DIP switch.
Use a DTBO file, talos-evk-lvds-auo,g133han01.dtso, which defines an overlay that disables HDMI and adds LVDS. The DTs file talos-evk can describe the HDMI display configurations.
The initial device tree includes support for:
- CPU and memory
- UART
- GPIOs
- Regulators
- PMIC
- Early console
- AT24MAC602 EEPROM
- MCP2515 SPI to CAN
- ADV7535 DSI-to-HDMI bridge
- DisplayPort interface
- SN65DSI84ZXHR DSI-to-LVDS bridge
- Wi-Fi/BTReviewed-by Dmitry Baryshkov <[email protected]>Signed-off-by Sudarshan Shetty <[email protected]>--- arch/arm64/boot/dts/qcom/Makefile | 4 + .../qcom/talos-evk-lvds-auo,g133han01.dtso | 126 ++++ arch/arm64/boot/dts/qcom/talos-evk-som.dtsi | 616 ++++++++++++++++++ arch/arm64/boot/dts/qcom/talos-evk.dts | 139 ++++ 4 files changed, 885 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-som.dtsi create mode 100644 arch/arm64/boot/dts/qcom/talos-evk.dtsarch/arm64/boot/dts/qcom/Makefile +4
-0@@ -324,6 +324,10 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8750-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8750-qrd.dtb +dtb-$(CONFIG_ARCH_QCOM) += talos-evk.dtb +talos-evk-lvds-auo,g133han01-dtbs := \ + talos-evk.dtb talos-evk-lvds-auo,g133han01.dtbo +dtb-$(CONFIG_ARCH_QCOM) += talos-evk-lvds-auo,g133han01.dtb x1e001de-devkit-el2-dtbs := x1e001de-devkit.dtb x1-el2.dtbo dtb-$(CONFIG_ARCH_QCOM) += x1e001de-devkit.dtb x1e001de-devkit-el2.dtb x1e78100-lenovo-thinkpad-t14s-el2-dtbs := x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtboarch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso new file +55
-0@@ -0,0 +1,126 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; +/plugin/; + +#include <dt-bindings/gpio/gpio.h> + +&{/} { + backlight: backlight { + compatible = "gpio-backlight"; + gpios = <&tlmm 59 GPIO_ACTIVE_HIGH>, + <&tlmm 115 GPIO_ACTIVE_HIGH>; + default-on; + }; + + panel-lvds { + compatible = "auo,g133han01"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* LVDS A (Odd pixels) */ + port@0 { + reg = <0>; + dual-lvds-odd-pixels; + + lvds_panel_out_a: endpoint { + remote-endpoint = <&sn65dsi84_out_a>; + }; + }; + + /* LVDS B (Even pixels) */ + port@1 { + reg = <1>; + dual-lvds-even-pixels; + + lvds_panel_out_b: endpoint { + remote-endpoint = <&sn65dsi84_out_b>; + }; + }; + }; + }; +}; + +&hdmi_connector { + status = "disabled"; +}; + +&i2c1 { + clock-frequency = <400000>; + + status = "okay";
Quoted 8 lines
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso line 61
Quoted 6 lines
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso new file +6
-0+ + hdmi_bridge: bridge@3d { + status = "disabled"; + }; + + lvds_bridge: bridge@2c {power-supply, if be optional, need to modify dt-binding file. otherwise we will meet binding check error.
Okay, got it. I will make necessary changes in the next patchset so that the binding check passes.
Quoted 11 lines
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso line 67
Quoted 7 lines
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso new file +6
-0+ compatible = "ti,sn65dsi84"; + reg = <0x2c>; + enable-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; + ti,dsi-lanes = <4>; + ti,lvds-format = "jeida-24"; + ti,lvds-bpp = <24>;ti,dsi-lanes, ti,lvds-format, ti,lvds-bpp, do we need these property? I don't see these property be used from kernel 6.6 to kernel 6.19.
Will drop these ti,dsi-lanes, ti,lvds-format, and ti,lvds-bpp properties in the next patchset.
Quoted 832 lines
Thanks,
YuanjieQuoted 827 lines
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso new file +58
-0+ ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + sn65dsi84_in: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@2 { + reg = <2>; + + sn65dsi84_out_a: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_a>; + }; + }; + + port@3 { + reg = <3>; + + sn65dsi84_out_b: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_b>; + }; + }; + }; + }; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l11a>; + + status = "okay"; +}; + +&mdss_dsi0_out { + remote-endpoint = <&sn65dsi84_in>; + data-lanes = <0 1 2 3>; +}; + +&tlmm { + lcd_bklt_en: lcd-bklt-en-state { + pins = "gpio115"; + function = "gpio"; + bias-disable; + }; + + lcd_bklt_pwm: lcd-bklt-pwm-state { + pins = "gpio59"; + function = "gpio"; + bias-disable; + }; +};arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +616
-0@@ -0,0 +1,616 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "talos.dtsi" +#include "pm8150.dtsi" +/ { + aliases { + mmc0 = &sdhc_1; + serial0 = &uart0; + serial1 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + clocks { + can_osc: can-oscillator { + compatible = "fixed-clock"; + clock-frequency = <20000000>; + #clock-cells = <0>; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32764>; + #clock-cells = <0>; + }; + + xo_board_clk: xo-board-clk { + compatible = "fixed-clock"; + clock-frequency = <38400000>; + #clock-cells = <0>; + }; + }; + + regulator-usb2-vbus { + compatible = "regulator-fixed"; + regulator-name = "USB2_VBUS"; + gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&usb2_en>; + pinctrl-names = "default"; + enable-active-high; + regulator-always-on; + }; + + vreg_conn_1p8: regulator-conn-1p8 { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_1p8"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 1 GPIO_ACTIVE_HIGH>; + }; + + vreg_conn_pa: regulator-conn-pa { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_pa"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 6 GPIO_ACTIVE_HIGH>; + }; + + vreg_v3p3_can: regulator-v3p3-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v3p3-can"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v5p0_can: regulator-v5p0-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v5p0-can"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + wcn6855-pmu { + compatible = "qcom,wcn6855-pmu"; + + pinctrl-0 = <&bt_en_state>, <&wlan_en_state>; + pinctrl-names = "default"; + + bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; + wlan-enable-gpios = <&tlmm 84 GPIO_ACTIVE_HIGH>; + + vddio-supply = <&vreg_conn_pa>; + vddaon-supply = <&vreg_s5a>; + vddpmu-supply = <&vreg_conn_1p8>; + vddpmumx-supply = <&vreg_conn_1p8>; + vddpmucx-supply = <&vreg_conn_pa>; + vddrfa0p95-supply = <&vreg_s5a>; + vddrfa1p3-supply = <&vreg_s6a>; + vddrfa1p9-supply = <&vreg_l15a>; + vddpcie1p3-supply = <&vreg_s6a>; + vddpcie1p9-supply = <&vreg_l15a>; + + regulators { + vreg_pmu_rfa_cmn: ldo0 { + regulator-name = "vreg_pmu_rfa_cmn"; + }; + + vreg_pmu_aon_0p59: ldo1 { + regulator-name = "vreg_pmu_aon_0p59"; + }; + + vreg_pmu_wlcx_0p8: ldo2 { + regulator-name = "vreg_pmu_wlcx_0p8"; + }; + + vreg_pmu_wlmx_0p85: ldo3 { + regulator-name = "vreg_pmu_wlmx_0p85"; + }; + + vreg_pmu_btcmx_0p85: ldo4 { + regulator-name = "vreg_pmu_btcmx_0p85"; + }; + + vreg_pmu_rfa_0p8: ldo5 { + regulator-name = "vreg_pmu_rfa_0p8"; + }; + + vreg_pmu_rfa_1p2: ldo6 { + regulator-name = "vreg_pmu_rfa_1p2"; + }; + + vreg_pmu_rfa_1p7: ldo7 { + regulator-name = "vreg_pmu_rfa_1p7"; + }; + + vreg_pmu_pcie_0p9: ldo8 { + regulator-name = "vreg_pmu_pcie_0p9"; + }; + + vreg_pmu_pcie_1p8: ldo9 { + regulator-name = "vreg_pmu_pcie_1p8"; + }; + }; + }; + + wifi_1p8v: regulator-wifi-1p8v { + compatible = "regulator-fixed"; + regulator-name = "wifi_1p8v"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; + + wifi_3p85v: regulator-wifi-3p85v { + compatible = "regulator-fixed"; + regulator-name = "wifi_3p85v"; + regulator-min-microvolt = <3850000>; + regulator-max-microvolt = <3850000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8150-rpmh-regulators"; + qcom,pmic-id = "a"; + + vreg_s3a: smps3 { + regulator-name = "vreg_s3a"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <650000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s4a: smps4 { + regulator-name = "vreg_s4a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1829000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s5a: smps5 { + regulator-name = "vreg_s5a"; + regulator-min-microvolt = <1896000>; + regulator-max-microvolt = <2040000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s6a: smps6 { + regulator-name = "vreg_s6a"; + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1404000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1a: ldo1 { + regulator-name = "vreg_l1a"; + regulator-min-microvolt = <488000>; + regulator-max-microvolt = <852000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2a: ldo2 { + regulator-name = "vreg_l2a"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3a: ldo3 { + regulator-name = "vreg_l3a"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1248000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5a: ldo5 { + regulator-name = "vreg_l5a"; + regulator-min-microvolt = <875000>; + regulator-max-microvolt = <975000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7a: ldo7 { + regulator-name = "vreg_l7a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1900000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8a: ldo8 { + regulator-name = "vreg_l8a"; + regulator-min-microvolt = <1150000>; + regulator-max-microvolt = <1350000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10a: ldo10 { + regulator-name = "vreg_l10a"; + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11a: ldo11 { + regulator-name = "vreg_l11a"; + regulator-min-microvolt = <1232000>; + regulator-max-microvolt = <1260000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12a: ldo12 { + regulator-name = "vreg_l12a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1890000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13a: ldo13 { + regulator-name = "vreg_l13a"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3230000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15a: ldo15 { + regulator-name = "vreg_l15a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1904000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l16a: ldo16 { + regulator-name = "vreg_l16a"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17a: ldo17 { + regulator-name = "vreg_l17a"; + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&gpi_dma0 { + status = "okay"; +}; + +&gpi_dma1 { + status = "okay"; +}; + +&i2c5 { + clock-frequency = <400000>; + status = "okay"; + + eeprom@57 { + compatible = "atmel,24c02"; + reg = <0x57>; + pagesize = <16>; + }; + + eeprom@5f { + compatible = "atmel,24mac602"; + reg = <0x5f>; + pagesize = <16>; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dp0 { + status = "okay"; +}; + +&mdss_dp0_out { + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000>; + remote-endpoint = <&dp0_connector_in>; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l11a>; + status = "okay"; +}; + +&mdss_dsi0_phy { + vcca-supply = <&vreg_l5a>; + status = "okay"; +}; + +&pcie { + perst-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&pcie_default_state>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie_phy { + vdda-phy-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + + status = "okay"; +}; + +&pcie_port0 { + wifi@0 { + compatible = "pci17cb,1103"; + reg = <0x10000 0x0 0x0 0x0 0x0>; + + qcom,calibration-variant = "QC_QCS615_Ride"; + + vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; + vddaon-supply = <&vreg_pmu_aon_0p59>; + vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; + vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; + vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>; + vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>; + vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>; + }; +}; + +&pm8150_gpios { + usb2_en: usb2-en-state { + pins = "gpio10"; + function = "normal"; + output-enable; + power-source = <0>; + }; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/qcs615/adsp.mbn"; + + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/qcs615/cdsp.mbn"; + + status = "okay"; +}; + +&sdhc_1 { + pinctrl-0 = <&sdc1_state_on>; + pinctrl-1 = <&sdc1_state_off>; + pinctrl-names = "default", "sleep"; + + bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + vmmc-supply = <&vreg_l17a>; + vqmmc-supply = <&vreg_s4a>; + + non-removable; + no-sd; + no-sdio; + + status = "okay"; +}; + +&spi6 { + status = "okay"; + + can@0 { + compatible = "microchip,mcp2515"; + reg = <0>; + clocks = <&can_osc>; + interrupts-extended = <&tlmm 87 IRQ_TYPE_LEVEL_LOW>; + spi-max-frequency = <10000000>; + vdd-supply = <&vreg_v3p3_can>; + xceiver-supply = <&vreg_v5p0_can>; + }; +}; + +&tlmm { + bt_en_state: bt-en-state { + pins = "gpio85"; + function = "gpio"; + bias-pull-down; + }; + + pcie_default_state: pcie-default-state { + clkreq-pins { + pins = "gpio90"; + function = "pcie_clk_req"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-pins { + pins = "gpio89"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-pins { + pins = "gpio100"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + wifi_reg_en_pins_state: wifi-reg-en-pins-state { + pins = "gpio91"; + function = "gpio"; + drive-strength = <8>; + output-high; + bias-pull-up; + }; + + wlan_en_state: wlan-en-state { + pins = "gpio84"; + function = "gpio"; + drive-strength = <16>; + bias-pull-down; + output-low; + }; +}; + +&uart0 { + status = "okay"; +}; + +&uart7 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn6855-bt"; + firmware-name = "QCA6698/hpnv21", "QCA6698/hpbtfw21.tlv"; + + vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; + vddaon-supply = <&vreg_pmu_aon_0p59>; + vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; + vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; + vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>; + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; + vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>; + }; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "host"; +}; + +&usb_hsphy_1 { + vdd-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + vdda-phy-dpdm-supply = <&vreg_l13a>; + + status = "okay"; +}; + +&usb_2 { + status = "okay"; +}; + +&usb_2_dwc3 { + dr_mode = "host"; +}; + +&usb_hsphy_2 { + vdd-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + vdda-phy-dpdm-supply = <&vreg_l13a>; + + status = "okay"; +}; + +&usb_qmpphy { + vdda-phy-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + + status = "okay"; +}; + +&usb_qmpphy_2 { + vdda-phy-supply = <&vreg_l11a>; + vdda-pll-supply = <&vreg_l5a>; + + status = "okay"; +}; + +&ufs_mem_hc { + reset-gpios = <&tlmm 123 GPIO_ACTIVE_LOW>; + vcc-supply = <&vreg_l17a>; + vcc-max-microamp = <600000>; + vccq2-supply = <&vreg_s4a>; + vccq2-max-microamp = <600000>; + + status = "okay"; +}; + +&ufs_mem_phy { + vdda-phy-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + + status = "okay"; +}; + +&venus { + status = "okay"; +};arch/arm64/boot/dts/qcom/talos-evk.dts new file +139
-0@@ -0,0 +1,139 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; + +#include "talos-evk-som.dtsi" + +/ { + model = "Qualcomm QCS615 IQ 615 EVK"; + compatible = "qcom,talos-evk", "qcom,qcs615", "qcom,sm6150"; + chassis-type = "embedded"; + + aliases { + mmc1 = &sdhc_2; + }; + + dp0-connector { + compatible = "dp-connector"; + label = "DP0"; + type = "full-size"; + + hpd-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>; + + port { + dp0_connector_in: endpoint { + remote-endpoint = <&mdss_dp0_out>; + }; + }; + }; + + hdmi_connector: hdmi-out { + compatible = "hdmi-connector"; + type = "d"; + + port { + hdmi_con_out: endpoint { + remote-endpoint = <&adv7535_out>; + }; + }; + }; + + vreg_v1p8_out: regulator-v1p8-out { + compatible = "regulator-fixed"; + regulator-name = "vreg-v1p8-out"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vreg_v5p0_out>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v3p3_out: regulator-v3p3-out { + compatible = "regulator-fixed"; + regulator-name = "vreg-v3p3-out"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vreg_v5p0_out>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v5p0_out: regulator-v5p0-out { + compatible = "regulator-fixed"; + regulator-name = "vreg-v5p0-out"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + /* Powered by system 20V rail (USBC_VBUS_IN) */ + }; +}; + +&i2c1 { + clock-frequency = <400000>; + status = "okay"; + + hdmi_bridge: bridge@3d { + compatible = "adi,adv7535"; + reg = <0x3d>; + avdd-supply = <&vreg_v1p8_out>; + dvdd-supply = <&vreg_v1p8_out>; + pvdd-supply = <&vreg_v1p8_out>; + a2vdd-supply = <&vreg_v1p8_out>; + v3p3-supply = <&vreg_v3p3_out>; + interrupts-extended = <&tlmm 26 IRQ_TYPE_LEVEL_LOW>; + adi,dsi-lanes = <4>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + adv7535_in: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + + adv7535_out: endpoint { + remote-endpoint = <&hdmi_con_out>; + }; + }; + }; + }; +}; + +&mdss_dsi0_out { + remote-endpoint = <&adv7535_in>; + data-lanes = <0 1 2 3>; +}; + +&pon_pwrkey { + status = "okay"; +}; + +&pon_resin { + linux,code = <KEY_VOLUMEDOWN>; + + status = "okay"; +}; + +&sdhc_2 { + pinctrl-0 = <&sdc2_state_on>; + pinctrl-1 = <&sdc2_state_off>; + pinctrl-names = "default", "sleep"; + + bus-width = <4>; + cd-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>; + + vmmc-supply = <&vreg_l10a>; + vqmmc-supply = <&vreg_s4a>; + + status = "okay"; +};Signature · 1 line
2.34.1
Re: [PATCH v11 4/4] arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board
In reply to Sudarshan ShettyQuoted 335 lines · Sudarshan Shetty
Add the device tree for the QCS615-based Talos EVK platform. The platform is composed of a System-on-Module following the SMARC standard, and a Carrier Board.
The Carrier Board supports several display configurations, HDMI and LVDS. Both configurations use the same base hardware, with the display selection controlled by a DIP switch.
Use a DTBO file, talos-evk-lvds-auo,g133han01.dtso, which defines an overlay that disables HDMI and adds LVDS. The DTs file talos-evk can describe the HDMI display configurations.
The initial device tree includes support for:
- CPU and memory
- UART
- GPIOs
- Regulators
- PMIC
- Early console
- AT24MAC602 EEPROM
- MCP2515 SPI to CAN
- ADV7535 DSI-to-HDMI bridge
- DisplayPort interface
- SN65DSI84ZXHR DSI-to-LVDS bridge
- Wi-Fi/BTReviewed-by Dmitry Baryshkov <[email protected]>Signed-off-by Sudarshan Shetty <[email protected]>--- arch/arm64/boot/dts/qcom/Makefile | 4 + .../qcom/talos-evk-lvds-auo,g133han01.dtso | 126 ++++ arch/arm64/boot/dts/qcom/talos-evk-som.dtsi | 616 ++++++++++++++++++ arch/arm64/boot/dts/qcom/talos-evk.dts | 139 ++++ 4 files changed, 885 insertions(+)create mode 100644
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtsocreate mode 100644arch/arm64/boot/dts/qcom/talos-evk-som.dtsicreate mode 100644arch/arm64/boot/dts/qcom/talos-evk.dtsarch/arm64/boot/dts/qcom/Makefile +4
-0@@ -324,6 +324,10 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8750-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8750-qrd.dtb +dtb-$(CONFIG_ARCH_QCOM) += talos-evk.dtb +talos-evk-lvds-auo,g133han01-dtbs := \ + talos-evk.dtb talos-evk-lvds-auo,g133han01.dtbo +dtb-$(CONFIG_ARCH_QCOM) += talos-evk-lvds-auo,g133han01.dtb x1e001de-devkit-el2-dtbs := x1e001de-devkit.dtb x1-el2.dtbo dtb-$(CONFIG_ARCH_QCOM) += x1e001de-devkit.dtb x1e001de-devkit-el2.dtb x1e78100-lenovo-thinkpad-t14s-el2-dtbs := x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtboarch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso new file +126
-0@@ -0,0 +1,126 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; +/plugin/; + +#include <dt-bindings/gpio/gpio.h> + +&{/} { + backlight: backlight { + compatible = "gpio-backlight"; + gpios = <&tlmm 59 GPIO_ACTIVE_HIGH>, + <&tlmm 115 GPIO_ACTIVE_HIGH>; + default-on; + }; + + panel-lvds { + compatible = "auo,g133han01"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* LVDS A (Odd pixels) */ + port@0 { + reg = <0>; + dual-lvds-odd-pixels; + + lvds_panel_out_a: endpoint { + remote-endpoint = <&sn65dsi84_out_a>; + }; + }; + + /* LVDS B (Even pixels) */ + port@1 { + reg = <1>; + dual-lvds-even-pixels; + + lvds_panel_out_b: endpoint { + remote-endpoint = <&sn65dsi84_out_b>; + }; + }; + }; + }; +}; + +&hdmi_connector { + status = "disabled"; +}; + +&i2c1 { + clock-frequency = <400000>; + + status = "okay"; + + hdmi_bridge: bridge@3d { + status = "disabled"; + }; + + lvds_bridge: bridge@2c { + compatible = "ti,sn65dsi84"; + reg = <0x2c>; + enable-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; + ti,dsi-lanes = <4>; + ti,lvds-format = "jeida-24"; + ti,lvds-bpp = <24>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + sn65dsi84_in: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@2 { + reg = <2>; + + sn65dsi84_out_a: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_a>; + }; + }; + + port@3 { + reg = <3>; + + sn65dsi84_out_b: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_b>; + }; + }; + }; + }; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l11a>; + + status = "okay"; +}; + +&mdss_dsi0_out { + remote-endpoint = <&sn65dsi84_in>; + data-lanes = <0 1 2 3>; +}; + +&tlmm { + lcd_bklt_en: lcd-bklt-en-state { + pins = "gpio115"; + function = "gpio"; + bias-disable; + }; + + lcd_bklt_pwm: lcd-bklt-pwm-state { + pins = "gpio59"; + function = "gpio"; + bias-disable; + }; +};arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +144
-0@@ -0,0 +1,616 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "talos.dtsi" +#include "pm8150.dtsi" +/ { + aliases { + mmc0 = &sdhc_1; + serial0 = &uart0; + serial1 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + clocks { + can_osc: can-oscillator { + compatible = "fixed-clock"; + clock-frequency = <20000000>; + #clock-cells = <0>; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32764>; + #clock-cells = <0>; + }; + + xo_board_clk: xo-board-clk { + compatible = "fixed-clock"; + clock-frequency = <38400000>; + #clock-cells = <0>; + }; + }; + + regulator-usb2-vbus { + compatible = "regulator-fixed"; + regulator-name = "USB2_VBUS"; + gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&usb2_en>; + pinctrl-names = "default"; + enable-active-high; + regulator-always-on; + }; + + vreg_conn_1p8: regulator-conn-1p8 { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_1p8"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 1 GPIO_ACTIVE_HIGH>; + }; + + vreg_conn_pa: regulator-conn-pa { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_pa"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 6 GPIO_ACTIVE_HIGH>; + }; + + vreg_v3p3_can: regulator-v3p3-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v3p3-can"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v5p0_can: regulator-v5p0-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v5p0-can"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + wcn6855-pmu { + compatible = "qcom,wcn6855-pmu"; + + pinctrl-0 = <&bt_en_state>, <&wlan_en_state>; + pinctrl-names = "default"; + + bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; + wlan-enable-gpios = <&tlmm 84 GPIO_ACTIVE_HIGH>; + + vddio-supply = <&vreg_conn_pa>; + vddaon-supply = <&vreg_s5a>; + vddpmu-supply = <&vreg_conn_1p8>; + vddpmumx-supply = <&vreg_conn_1p8>; + vddpmucx-supply = <&vreg_conn_pa>; + vddrfa0p95-supply = <&vreg_s5a>; + vddrfa1p3-supply = <&vreg_s6a>; + vddrfa1p9-supply = <&vreg_l15a>; + vddpcie1p3-supply = <&vreg_s6a>; + vddpcie1p9-supply = <&vreg_l15a>; + + regulators { + vreg_pmu_rfa_cmn: ldo0 { + regulator-name = "vreg_pmu_rfa_cmn"; + }; + + vreg_pmu_aon_0p59: ldo1 { + regulator-name = "vreg_pmu_aon_0p59"; + }; + + vreg_pmu_wlcx_0p8: ldo2 { + regulator-name = "vreg_pmu_wlcx_0p8"; + }; + + vreg_pmu_wlmx_0p85: ldo3 { + regulator-name = "vreg_pmu_wlmx_0p85"; + }; + + vreg_pmu_btcmx_0p85: ldo4 { + regulator-name = "vreg_pmu_btcmx_0p85"; + }; + + vreg_pmu_rfa_0p8: ldo5 { + regulator-name = "vreg_pmu_rfa_0p8"; + }; + + vreg_pmu_rfa_1p2: ldo6 { + regulator-name = "vreg_pmu_rfa_1p2"; + }; + + vreg_pmu_rfa_1p7: ldo7 { + regulator-name = "vreg_pmu_rfa_1p7"; + }; + + vreg_pmu_pcie_0p9: ldo8 { + regulator-name = "vreg_pmu_pcie_0p9"; + }; + + vreg_pmu_pcie_1p8: ldo9 { + regulator-name = "vreg_pmu_pcie_1p8";
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 154
Quoted 10 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +10
-0+ }; + }; + }; + + wifi_1p8v: regulator-wifi-1p8v { + compatible = "regulator-fixed"; + regulator-name = "wifi_1p8v"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;
Please check this pin number
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 167
Quoted 13 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +13
-0+ enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; + + wifi_3p85v: regulator-wifi-3p85v { + compatible = "regulator-fixed"; + regulator-name = "wifi_3p85v"; + regulator-min-microvolt = <3850000>; + regulator-max-microvolt = <3850000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;
Please check this pin number
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 173
Quoted 7 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +7
-0+ enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; +};
Are these two node necessary?
Quoted 218 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +218
-0+ +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8150-rpmh-regulators"; + qcom,pmic-id = "a"; + + vreg_s3a: smps3 { + regulator-name = "vreg_s3a"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <650000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s4a: smps4 { + regulator-name = "vreg_s4a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1829000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s5a: smps5 { + regulator-name = "vreg_s5a"; + regulator-min-microvolt = <1896000>; + regulator-max-microvolt = <2040000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s6a: smps6 { + regulator-name = "vreg_s6a"; + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1404000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1a: ldo1 { + regulator-name = "vreg_l1a"; + regulator-min-microvolt = <488000>; + regulator-max-microvolt = <852000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2a: ldo2 { + regulator-name = "vreg_l2a"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3a: ldo3 { + regulator-name = "vreg_l3a"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1248000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5a: ldo5 { + regulator-name = "vreg_l5a"; + regulator-min-microvolt = <875000>; + regulator-max-microvolt = <975000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7a: ldo7 { + regulator-name = "vreg_l7a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1900000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8a: ldo8 { + regulator-name = "vreg_l8a"; + regulator-min-microvolt = <1150000>; + regulator-max-microvolt = <1350000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10a: ldo10 { + regulator-name = "vreg_l10a"; + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11a: ldo11 { + regulator-name = "vreg_l11a"; + regulator-min-microvolt = <1232000>; + regulator-max-microvolt = <1260000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12a: ldo12 { + regulator-name = "vreg_l12a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1890000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13a: ldo13 { + regulator-name = "vreg_l13a"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3230000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15a: ldo15 { + regulator-name = "vreg_l15a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1904000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l16a: ldo16 { + regulator-name = "vreg_l16a"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17a: ldo17 { + regulator-name = "vreg_l17a"; + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&gpi_dma0 { + status = "okay"; +}; + +&gpi_dma1 { + status = "okay"; +}; + +&i2c5 { + clock-frequency = <400000>; + status = "okay"; + + eeprom@57 { + compatible = "atmel,24c02"; + reg = <0x57>; + pagesize = <16>; + }; + + eeprom@5f { + compatible = "atmel,24mac602"; + reg = <0x5f>; + pagesize = <16>; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dp0 { + status = "okay"; +}; + +&mdss_dp0_out { + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000>; + remote-endpoint = <&dp0_connector_in>; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l11a>; + status = "okay"; +}; + +&mdss_dsi0_phy { + vcca-supply = <&vreg_l5a>; + status = "okay"; +}; + +&pcie { + perst-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&pcie_default_state>; + pinctrl-names = "default"; + + status = "okay"; +}; +
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 402
Quoted 10 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +10
-0+&pcie_phy { + vdda-phy-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + + status = "okay"; +}; + +&pcie_port0 { + wifi@0 { + compatible = "pci17cb,1103";
This style of writing is not very readable.
Quoted 359 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +214
-0+ reg = <0x10000 0x0 0x0 0x0 0x0>; + + qcom,calibration-variant = "QC_QCS615_Ride"; + + vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; + vddaon-supply = <&vreg_pmu_aon_0p59>; + vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; + vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; + vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>; + vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>; + vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>; + }; +}; + +&pm8150_gpios { + usb2_en: usb2-en-state { + pins = "gpio10"; + function = "normal"; + output-enable; + power-source = <0>; + }; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/qcs615/adsp.mbn"; + + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/qcs615/cdsp.mbn"; + + status = "okay"; +}; + +&sdhc_1 { + pinctrl-0 = <&sdc1_state_on>; + pinctrl-1 = <&sdc1_state_off>; + pinctrl-names = "default", "sleep"; + + bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + vmmc-supply = <&vreg_l17a>; + vqmmc-supply = <&vreg_s4a>; + + non-removable; + no-sd; + no-sdio; + + status = "okay"; +}; + +&spi6 { + status = "okay"; + + can@0 { + compatible = "microchip,mcp2515"; + reg = <0>; + clocks = <&can_osc>; + interrupts-extended = <&tlmm 87 IRQ_TYPE_LEVEL_LOW>; + spi-max-frequency = <10000000>; + vdd-supply = <&vreg_v3p3_can>; + xceiver-supply = <&vreg_v5p0_can>; + }; +}; + +&tlmm { + bt_en_state: bt-en-state { + pins = "gpio85"; + function = "gpio"; + bias-pull-down; + }; + + pcie_default_state: pcie-default-state { + clkreq-pins { + pins = "gpio90"; + function = "pcie_clk_req"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-pins { + pins = "gpio89"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-pins { + pins = "gpio100"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + wifi_reg_en_pins_state: wifi-reg-en-pins-state { + pins = "gpio91"; + function = "gpio"; + drive-strength = <8>; + output-high; + bias-pull-up; + }; + + wlan_en_state: wlan-en-state { + pins = "gpio84"; + function = "gpio"; + drive-strength = <16>; + bias-pull-down; + output-low; + }; +}; + +&uart0 { + status = "okay"; +}; + +&uart7 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn6855-bt"; + firmware-name = "QCA6698/hpnv21", "QCA6698/hpbtfw21.tlv"; + + vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; + vddaon-supply = <&vreg_pmu_aon_0p59>; + vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; + vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; + vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>; + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; + vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>; + }; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "host"; +}; + +&usb_hsphy_1 { + vdd-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + vdda-phy-dpdm-supply = <&vreg_l13a>; + + status = "okay"; +}; + +&usb_2 { + status = "okay"; +}; + +&usb_2_dwc3 { + dr_mode = "host"; +}; + +&usb_hsphy_2 { + vdd-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + vdda-phy-dpdm-supply = <&vreg_l13a>; + + status = "okay"; +}; + +&usb_qmpphy { + vdda-phy-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + + status = "okay"; +}; + +&usb_qmpphy_2 { + vdda-phy-supply = <&vreg_l11a>; + vdda-pll-supply = <&vreg_l5a>; + + status = "okay"; +}; + +&ufs_mem_hc { + reset-gpios = <&tlmm 123 GPIO_ACTIVE_LOW>; + vcc-supply = <&vreg_l17a>; + vcc-max-microamp = <600000>; + vccq2-supply = <&vreg_s4a>; + vccq2-max-microamp = <600000>; + + status = "okay"; +}; + +&ufs_mem_phy { + vdda-phy-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + + status = "okay"; +}; + +&venus { + status = "okay"; +};arch/arm64/boot/dts/qcom/talos-evk.dts new file +139
-0@@ -0,0 +1,139 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; + +#include "talos-evk-som.dtsi" + +/ { + model = "Qualcomm QCS615 IQ 615 EVK"; + compatible = "qcom,talos-evk", "qcom,qcs615", "qcom,sm6150"; + chassis-type = "embedded"; + + aliases { + mmc1 = &sdhc_2; + }; + + dp0-connector { + compatible = "dp-connector"; + label = "DP0"; + type = "full-size"; + + hpd-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>; + + port { + dp0_connector_in: endpoint { + remote-endpoint = <&mdss_dp0_out>; + }; + }; + }; + + hdmi_connector: hdmi-out { + compatible = "hdmi-connector"; + type = "d"; + + port { + hdmi_con_out: endpoint { + remote-endpoint = <&adv7535_out>; + }; + }; + }; + + vreg_v1p8_out: regulator-v1p8-out { + compatible = "regulator-fixed"; + regulator-name = "vreg-v1p8-out"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vreg_v5p0_out>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v3p3_out: regulator-v3p3-out { + compatible = "regulator-fixed"; + regulator-name = "vreg-v3p3-out"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vreg_v5p0_out>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v5p0_out: regulator-v5p0-out { + compatible = "regulator-fixed"; + regulator-name = "vreg-v5p0-out"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + /* Powered by system 20V rail (USBC_VBUS_IN) */ + }; +}; + +&i2c1 { + clock-frequency = <400000>; + status = "okay"; + + hdmi_bridge: bridge@3d { + compatible = "adi,adv7535"; + reg = <0x3d>; + avdd-supply = <&vreg_v1p8_out>; + dvdd-supply = <&vreg_v1p8_out>; + pvdd-supply = <&vreg_v1p8_out>; + a2vdd-supply = <&vreg_v1p8_out>; + v3p3-supply = <&vreg_v3p3_out>; + interrupts-extended = <&tlmm 26 IRQ_TYPE_LEVEL_LOW>; + adi,dsi-lanes = <4>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + adv7535_in: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + + adv7535_out: endpoint { + remote-endpoint = <&hdmi_con_out>; + }; + }; + }; + }; +}; + +&mdss_dsi0_out { + remote-endpoint = <&adv7535_in>; + data-lanes = <0 1 2 3>; +}; + +&pon_pwrkey { + status = "okay"; +}; + +&pon_resin { + linux,code = <KEY_VOLUMEDOWN>; + + status = "okay"; +}; + +&sdhc_2 { + pinctrl-0 = <&sdc2_state_on>; + pinctrl-1 = <&sdc2_state_off>; + pinctrl-names = "default", "sleep"; + + bus-width = <4>; + cd-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>; + + vmmc-supply = <&vreg_l10a>; + vqmmc-supply = <&vreg_s4a>; + + status = "okay"; +};
Re: [PATCH v11 4/4] arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board
Quoted 371 lines · Qian Zhang
Quoted 335 lines · Sudarshan Shetty
Add the device tree for the QCS615-based Talos EVK platform. The platform is composed of a System-on-Module following the SMARC standard, and a Carrier Board.
The Carrier Board supports several display configurations, HDMI and LVDS. Both configurations use the same base hardware, with the display selection controlled by a DIP switch.
Use a DTBO file, talos-evk-lvds-auo,g133han01.dtso, which defines an overlay that disables HDMI and adds LVDS. The DTs file talos-evk can describe the HDMI display configurations.
The initial device tree includes support for:
- CPU and memory
- UART
- GPIOs
- Regulators
- PMIC
- Early console
- AT24MAC602 EEPROM
- MCP2515 SPI to CAN
- ADV7535 DSI-to-HDMI bridge
- DisplayPort interface
- SN65DSI84ZXHR DSI-to-LVDS bridge
- Wi-Fi/BTReviewed-by Dmitry Baryshkov <[email protected]>Signed-off-by Sudarshan Shetty <[email protected]>---
arch/arm64/boot/dts/qcom/Makefile | 4 + .../qcom/talos-evk-lvds-auo,g133han01.dtso | 126 ++++ arch/arm64/boot/dts/qcom/talos-evk-som.dtsi | 616 ++++++++++++++++++ arch/arm64/boot/dts/qcom/talos-evk.dts | 139 ++++4 files changed, 885 insertions(+)create mode 100644
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtsocreate mode 100644arch/arm64/boot/dts/qcom/talos-evk-som.dtsicreate mode 100644arch/arm64/boot/dts/qcom/talos-evk.dtsarch/arm64/boot/dts/qcom/Makefile +0
-0@@ -324,6 +324,10 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtbdtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-qrd.dtbarch/arm64/boot/dts/qcom/Makefile +4
-0+dtb-$(CONFIG_ARCH_QCOM) += talos-evk.dtb +talos-evk-lvds-auo,g133han01-dtbs := \ + talos-evk.dtb talos-evk-lvds-auo,g133han01.dtbo +dtb-$(CONFIG_ARCH_QCOM) += talos-evk-lvds-auo,g133han01.dtbx1e001de-devkit-el2-dtbs := x1e001de-devkit.dtb x1-el2.dtbo dtb-$(CONFIG_ARCH_QCOM) += x1e001de-devkit.dtb x1e001de-devkit-el2.dtb x1e78100-lenovo-thinkpad-t14s-el2-dtbs := x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso new file +126
-0@@ -0,0 +1,126 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; +/plugin/; + +#include <dt-bindings/gpio/gpio.h> + +&{/} { + backlight: backlight { + compatible = "gpio-backlight"; + gpios = <&tlmm 59 GPIO_ACTIVE_HIGH>, + <&tlmm 115 GPIO_ACTIVE_HIGH>; + default-on; + }; + + panel-lvds { + compatible = "auo,g133han01"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* LVDS A (Odd pixels) */ + port@0 { + reg = <0>; + dual-lvds-odd-pixels; + + lvds_panel_out_a: endpoint { + remote-endpoint = <&sn65dsi84_out_a>; + }; + }; + + /* LVDS B (Even pixels) */ + port@1 { + reg = <1>; + dual-lvds-even-pixels; + + lvds_panel_out_b: endpoint { + remote-endpoint = <&sn65dsi84_out_b>; + }; + }; + }; + }; +}; + +&hdmi_connector { + status = "disabled"; +}; + +&i2c1 { + clock-frequency = <400000>; + + status = "okay"; + + hdmi_bridge: bridge@3d { + status = "disabled"; + }; + + lvds_bridge: bridge@2c { + compatible = "ti,sn65dsi84"; + reg = <0x2c>; + enable-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; + ti,dsi-lanes = <4>; + ti,lvds-format = "jeida-24"; + ti,lvds-bpp = <24>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + sn65dsi84_in: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@2 { + reg = <2>; + + sn65dsi84_out_a: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_a>; + }; + }; + + port@3 { + reg = <3>; + + sn65dsi84_out_b: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_b>; + }; + }; + }; + }; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l11a>; + + status = "okay"; +}; + +&mdss_dsi0_out { + remote-endpoint = <&sn65dsi84_in>; + data-lanes = <0 1 2 3>; +}; + +&tlmm { + lcd_bklt_en: lcd-bklt-en-state { + pins = "gpio115"; + function = "gpio"; + bias-disable; + }; + + lcd_bklt_pwm: lcd-bklt-pwm-state { + pins = "gpio59"; + function = "gpio"; + bias-disable; + }; +};arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +144
-0@@ -0,0 +1,616 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "talos.dtsi" +#include "pm8150.dtsi" +/ { + aliases { + mmc0 = &sdhc_1; + serial0 = &uart0; + serial1 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + clocks { + can_osc: can-oscillator { + compatible = "fixed-clock"; + clock-frequency = <20000000>; + #clock-cells = <0>; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32764>; + #clock-cells = <0>; + }; + + xo_board_clk: xo-board-clk { + compatible = "fixed-clock"; + clock-frequency = <38400000>; + #clock-cells = <0>; + }; + }; + + regulator-usb2-vbus { + compatible = "regulator-fixed"; + regulator-name = "USB2_VBUS"; + gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&usb2_en>; + pinctrl-names = "default"; + enable-active-high; + regulator-always-on; + }; + + vreg_conn_1p8: regulator-conn-1p8 { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_1p8"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 1 GPIO_ACTIVE_HIGH>; + }; + + vreg_conn_pa: regulator-conn-pa { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_pa"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 6 GPIO_ACTIVE_HIGH>; + }; + + vreg_v3p3_can: regulator-v3p3-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v3p3-can"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v5p0_can: regulator-v5p0-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v5p0-can"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + wcn6855-pmu { + compatible = "qcom,wcn6855-pmu"; + + pinctrl-0 = <&bt_en_state>, <&wlan_en_state>; + pinctrl-names = "default"; + + bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; + wlan-enable-gpios = <&tlmm 84 GPIO_ACTIVE_HIGH>; + + vddio-supply = <&vreg_conn_pa>; + vddaon-supply = <&vreg_s5a>; + vddpmu-supply = <&vreg_conn_1p8>; + vddpmumx-supply = <&vreg_conn_1p8>; + vddpmucx-supply = <&vreg_conn_pa>; + vddrfa0p95-supply = <&vreg_s5a>; + vddrfa1p3-supply = <&vreg_s6a>; + vddrfa1p9-supply = <&vreg_l15a>; + vddpcie1p3-supply = <&vreg_s6a>; + vddpcie1p9-supply = <&vreg_l15a>; + + regulators { + vreg_pmu_rfa_cmn: ldo0 { + regulator-name = "vreg_pmu_rfa_cmn"; + }; + + vreg_pmu_aon_0p59: ldo1 { + regulator-name = "vreg_pmu_aon_0p59"; + }; + + vreg_pmu_wlcx_0p8: ldo2 { + regulator-name = "vreg_pmu_wlcx_0p8"; + }; + + vreg_pmu_wlmx_0p85: ldo3 { + regulator-name = "vreg_pmu_wlmx_0p85"; + }; + + vreg_pmu_btcmx_0p85: ldo4 { + regulator-name = "vreg_pmu_btcmx_0p85"; + }; + + vreg_pmu_rfa_0p8: ldo5 { + regulator-name = "vreg_pmu_rfa_0p8"; + }; + + vreg_pmu_rfa_1p2: ldo6 { + regulator-name = "vreg_pmu_rfa_1p2"; + }; + + vreg_pmu_rfa_1p7: ldo7 { + regulator-name = "vreg_pmu_rfa_1p7"; + }; + + vreg_pmu_pcie_0p9: ldo8 { + regulator-name = "vreg_pmu_pcie_0p9"; + }; + + vreg_pmu_pcie_1p8: ldo9 { + regulator-name = "vreg_pmu_pcie_1p8";arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 154
Quoted 10 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +10
-0+ }; + }; + }; + + wifi_1p8v: regulator-wifi-1p8v { + compatible = "regulator-fixed"; + regulator-name = "wifi_1p8v"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;Please check this pin number
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 167
Quoted 13 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +13
-0+ enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; + + wifi_3p85v: regulator-wifi-3p85v { + compatible = "regulator-fixed"; + regulator-name = "wifi_3p85v"; + regulator-min-microvolt = <3850000>; + regulator-max-microvolt = <3850000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;Please check this pin number
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 173
Quoted 7 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +7
-0+ enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; +};
Quoted 2 lines
Are these two node necessary?
On this board, GPIO91 is wired as a common enable for both WiFi power rails: WiFi 1.8V and WiFi 3.85V.
I currently modeled them as two regulator-fixed nodes because these are two distinct rails.
Would you prefer modelling a single regulator node that controls the shared GPIO as below:
wifi_en: regulator-wifi-en {
compatible = "regulator-fixed";
regulator-name = "wifi_en";
gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;
enable-active-high;
pinctrl-0 = <&wifi_reg_en_pins_state>;
pinctrl-names = "default";
regulator-boot-on;
regulator-always-on;
};Quoted 591 lines
Quoted 218 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +218
-0+ +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8150-rpmh-regulators"; + qcom,pmic-id = "a"; + + vreg_s3a: smps3 { + regulator-name = "vreg_s3a"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <650000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s4a: smps4 { + regulator-name = "vreg_s4a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1829000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s5a: smps5 { + regulator-name = "vreg_s5a"; + regulator-min-microvolt = <1896000>; + regulator-max-microvolt = <2040000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s6a: smps6 { + regulator-name = "vreg_s6a"; + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1404000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1a: ldo1 { + regulator-name = "vreg_l1a"; + regulator-min-microvolt = <488000>; + regulator-max-microvolt = <852000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2a: ldo2 { + regulator-name = "vreg_l2a"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3a: ldo3 { + regulator-name = "vreg_l3a"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1248000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5a: ldo5 { + regulator-name = "vreg_l5a"; + regulator-min-microvolt = <875000>; + regulator-max-microvolt = <975000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7a: ldo7 { + regulator-name = "vreg_l7a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1900000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8a: ldo8 { + regulator-name = "vreg_l8a"; + regulator-min-microvolt = <1150000>; + regulator-max-microvolt = <1350000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10a: ldo10 { + regulator-name = "vreg_l10a"; + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11a: ldo11 { + regulator-name = "vreg_l11a"; + regulator-min-microvolt = <1232000>; + regulator-max-microvolt = <1260000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12a: ldo12 { + regulator-name = "vreg_l12a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1890000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13a: ldo13 { + regulator-name = "vreg_l13a"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3230000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15a: ldo15 { + regulator-name = "vreg_l15a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1904000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l16a: ldo16 { + regulator-name = "vreg_l16a"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17a: ldo17 { + regulator-name = "vreg_l17a"; + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&gpi_dma0 { + status = "okay"; +}; + +&gpi_dma1 { + status = "okay"; +}; + +&i2c5 { + clock-frequency = <400000>; + status = "okay"; + + eeprom@57 { + compatible = "atmel,24c02"; + reg = <0x57>; + pagesize = <16>; + }; + + eeprom@5f { + compatible = "atmel,24mac602"; + reg = <0x5f>; + pagesize = <16>; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dp0 { + status = "okay"; +}; + +&mdss_dp0_out { + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000>; + remote-endpoint = <&dp0_connector_in>; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l11a>; + status = "okay"; +}; + +&mdss_dsi0_phy { + vcca-supply = <&vreg_l5a>; + status = "okay"; +}; + +&pcie { + perst-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&pcie_default_state>; + pinctrl-names = "default"; + + status = "okay"; +}; +arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 402
Quoted 10 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +10
-0+&pcie_phy { + vdda-phy-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + + status = "okay"; +}; + +&pcie_port0 { + wifi@0 { + compatible = "pci17cb,1103";This style of writing is not very readable.
Quoted 359 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +214
-0+ reg = <0x10000 0x0 0x0 0x0 0x0>; + + qcom,calibration-variant = "QC_QCS615_Ride"; + + vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; + vddaon-supply = <&vreg_pmu_aon_0p59>; + vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; + vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; + vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>; + vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>; + vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>; + }; +}; + +&pm8150_gpios { + usb2_en: usb2-en-state { + pins = "gpio10"; + function = "normal"; + output-enable; + power-source = <0>; + }; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/qcs615/adsp.mbn"; + + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/qcs615/cdsp.mbn"; + + status = "okay"; +}; + +&sdhc_1 { + pinctrl-0 = <&sdc1_state_on>; + pinctrl-1 = <&sdc1_state_off>; + pinctrl-names = "default", "sleep"; + + bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + vmmc-supply = <&vreg_l17a>; + vqmmc-supply = <&vreg_s4a>; + + non-removable; + no-sd; + no-sdio; + + status = "okay"; +}; + +&spi6 { + status = "okay"; + + can@0 { + compatible = "microchip,mcp2515"; + reg = <0>; + clocks = <&can_osc>; + interrupts-extended = <&tlmm 87 IRQ_TYPE_LEVEL_LOW>; + spi-max-frequency = <10000000>; + vdd-supply = <&vreg_v3p3_can>; + xceiver-supply = <&vreg_v5p0_can>; + }; +}; + +&tlmm { + bt_en_state: bt-en-state { + pins = "gpio85"; + function = "gpio"; + bias-pull-down; + }; + + pcie_default_state: pcie-default-state { + clkreq-pins { + pins = "gpio90"; + function = "pcie_clk_req"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-pins { + pins = "gpio89"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-pins { + pins = "gpio100"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + wifi_reg_en_pins_state: wifi-reg-en-pins-state { + pins = "gpio91"; + function = "gpio"; + drive-strength = <8>; + output-high; + bias-pull-up; + }; + + wlan_en_state: wlan-en-state { + pins = "gpio84"; + function = "gpio"; + drive-strength = <16>; + bias-pull-down; + output-low; + }; +}; + +&uart0 { + status = "okay"; +}; + +&uart7 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn6855-bt"; + firmware-name = "QCA6698/hpnv21", "QCA6698/hpbtfw21.tlv"; + + vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; + vddaon-supply = <&vreg_pmu_aon_0p59>; + vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; + vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; + vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>; + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; + vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>; + }; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "host"; +}; + +&usb_hsphy_1 { + vdd-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + vdda-phy-dpdm-supply = <&vreg_l13a>; + + status = "okay"; +}; + +&usb_2 { + status = "okay"; +}; + +&usb_2_dwc3 { + dr_mode = "host"; +}; + +&usb_hsphy_2 { + vdd-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + vdda-phy-dpdm-supply = <&vreg_l13a>; + + status = "okay"; +}; + +&usb_qmpphy { + vdda-phy-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + + status = "okay"; +}; + +&usb_qmpphy_2 { + vdda-phy-supply = <&vreg_l11a>; + vdda-pll-supply = <&vreg_l5a>; + + status = "okay"; +}; + +&ufs_mem_hc { + reset-gpios = <&tlmm 123 GPIO_ACTIVE_LOW>; + vcc-supply = <&vreg_l17a>; + vcc-max-microamp = <600000>; + vccq2-supply = <&vreg_s4a>; + vccq2-max-microamp = <600000>; + + status = "okay"; +}; + +&ufs_mem_phy { + vdda-phy-supply = <&vreg_l5a>; + vdda-pll-supply = <&vreg_l12a>; + + status = "okay"; +}; + +&venus { + status = "okay"; +};arch/arm64/boot/dts/qcom/talos-evk.dts new file +139
-0@@ -0,0 +1,139 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; + +#include "talos-evk-som.dtsi" + +/ { + model = "Qualcomm QCS615 IQ 615 EVK"; + compatible = "qcom,talos-evk", "qcom,qcs615", "qcom,sm6150"; + chassis-type = "embedded"; + + aliases { + mmc1 = &sdhc_2; + }; + + dp0-connector { + compatible = "dp-connector"; + label = "DP0"; + type = "full-size"; + + hpd-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>; + + port { + dp0_connector_in: endpoint { + remote-endpoint = <&mdss_dp0_out>; + }; + }; + }; + + hdmi_connector: hdmi-out { + compatible = "hdmi-connector"; + type = "d"; + + port { + hdmi_con_out: endpoint { + remote-endpoint = <&adv7535_out>; + }; + }; + }; + + vreg_v1p8_out: regulator-v1p8-out { + compatible = "regulator-fixed"; + regulator-name = "vreg-v1p8-out"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vreg_v5p0_out>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v3p3_out: regulator-v3p3-out { + compatible = "regulator-fixed"; + regulator-name = "vreg-v3p3-out"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vreg_v5p0_out>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v5p0_out: regulator-v5p0-out { + compatible = "regulator-fixed"; + regulator-name = "vreg-v5p0-out"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + /* Powered by system 20V rail (USBC_VBUS_IN) */ + }; +}; + +&i2c1 { + clock-frequency = <400000>; + status = "okay"; + + hdmi_bridge: bridge@3d { + compatible = "adi,adv7535"; + reg = <0x3d>; + avdd-supply = <&vreg_v1p8_out>; + dvdd-supply = <&vreg_v1p8_out>; + pvdd-supply = <&vreg_v1p8_out>; + a2vdd-supply = <&vreg_v1p8_out>; + v3p3-supply = <&vreg_v3p3_out>; + interrupts-extended = <&tlmm 26 IRQ_TYPE_LEVEL_LOW>; + adi,dsi-lanes = <4>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + adv7535_in: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + + adv7535_out: endpoint { + remote-endpoint = <&hdmi_con_out>; + }; + }; + }; + }; +}; + +&mdss_dsi0_out { + remote-endpoint = <&adv7535_in>; + data-lanes = <0 1 2 3>; +}; + +&pon_pwrkey { + status = "okay"; +}; + +&pon_resin { + linux,code = <KEY_VOLUMEDOWN>; + + status = "okay"; +}; + +&sdhc_2 { + pinctrl-0 = <&sdc2_state_on>; + pinctrl-1 = <&sdc2_state_off>; + pinctrl-names = "default", "sleep"; + + bus-width = <4>; + cd-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>; + + vmmc-supply = <&vreg_l10a>; + vqmmc-supply = <&vreg_s4a>; + + status = "okay"; +};
Re: [PATCH v11 4/4] arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board
Quoted 384 lines · On Fri, Jan 16, 2026 at 12:28:22PM +0530, [email protected] wrote:
Quoted 371 lines · Qian Zhang
Quoted 335 lines · Sudarshan Shetty
Add the device tree for the QCS615-based Talos EVK platform. The platform is composed of a System-on-Module following the SMARC standard, and a Carrier Board.
The Carrier Board supports several display configurations, HDMI and LVDS. Both configurations use the same base hardware, with the display selection controlled by a DIP switch.
Use a DTBO file, talos-evk-lvds-auo,g133han01.dtso, which defines an overlay that disables HDMI and adds LVDS. The DTs file talos-evk can describe the HDMI display configurations.
The initial device tree includes support for:
- CPU and memory
- UART
- GPIOs
- Regulators
- PMIC
- Early console
- AT24MAC602 EEPROM
- MCP2515 SPI to CAN
- ADV7535 DSI-to-HDMI bridge
- DisplayPort interface
- SN65DSI84ZXHR DSI-to-LVDS bridge
- Wi-Fi/BTReviewed-by Dmitry Baryshkov <[email protected]>Signed-off-by Sudarshan Shetty <[email protected]>---
arch/arm64/boot/dts/qcom/Makefile | 4 + .../qcom/talos-evk-lvds-auo,g133han01.dtso | 126 ++++ arch/arm64/boot/dts/qcom/talos-evk-som.dtsi | 616 ++++++++++++++++++ arch/arm64/boot/dts/qcom/talos-evk.dts | 139 ++++4 files changed, 885 insertions(+)create mode 100644
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtsocreate mode 100644arch/arm64/boot/dts/qcom/talos-evk-som.dtsicreate mode 100644arch/arm64/boot/dts/qcom/talos-evk.dtsarch/arm64/boot/dts/qcom/Makefile +0
-0@@ -324,6 +324,10 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtbdtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-qrd.dtbarch/arm64/boot/dts/qcom/Makefile +4
-0+dtb-$(CONFIG_ARCH_QCOM) += talos-evk.dtb +talos-evk-lvds-auo,g133han01-dtbs := \ + talos-evk.dtb talos-evk-lvds-auo,g133han01.dtbo +dtb-$(CONFIG_ARCH_QCOM) += talos-evk-lvds-auo,g133han01.dtbx1e001de-devkit-el2-dtbs := x1e001de-devkit.dtb x1-el2.dtbo dtb-$(CONFIG_ARCH_QCOM) += x1e001de-devkit.dtb x1e001de-devkit-el2.dtb x1e78100-lenovo-thinkpad-t14s-el2-dtbs := x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso new file +126
-0@@ -0,0 +1,126 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; +/plugin/; + +#include <dt-bindings/gpio/gpio.h> + +&{/} { + backlight: backlight { + compatible = "gpio-backlight"; + gpios = <&tlmm 59 GPIO_ACTIVE_HIGH>, + <&tlmm 115 GPIO_ACTIVE_HIGH>; + default-on; + }; + + panel-lvds { + compatible = "auo,g133han01"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* LVDS A (Odd pixels) */ + port@0 { + reg = <0>; + dual-lvds-odd-pixels; + + lvds_panel_out_a: endpoint { + remote-endpoint = <&sn65dsi84_out_a>; + }; + }; + + /* LVDS B (Even pixels) */ + port@1 { + reg = <1>; + dual-lvds-even-pixels; + + lvds_panel_out_b: endpoint { + remote-endpoint = <&sn65dsi84_out_b>; + }; + }; + }; + }; +}; + +&hdmi_connector { + status = "disabled"; +}; + +&i2c1 { + clock-frequency = <400000>; + + status = "okay"; + + hdmi_bridge: bridge@3d { + status = "disabled"; + }; + + lvds_bridge: bridge@2c { + compatible = "ti,sn65dsi84"; + reg = <0x2c>; + enable-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; + ti,dsi-lanes = <4>; + ti,lvds-format = "jeida-24"; + ti,lvds-bpp = <24>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + sn65dsi84_in: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@2 { + reg = <2>; + + sn65dsi84_out_a: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_a>; + }; + }; + + port@3 { + reg = <3>; + + sn65dsi84_out_b: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_b>; + }; + }; + }; + }; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l11a>; + + status = "okay"; +}; + +&mdss_dsi0_out { + remote-endpoint = <&sn65dsi84_in>; + data-lanes = <0 1 2 3>; +}; + +&tlmm { + lcd_bklt_en: lcd-bklt-en-state { + pins = "gpio115"; + function = "gpio"; + bias-disable; + }; + + lcd_bklt_pwm: lcd-bklt-pwm-state { + pins = "gpio59"; + function = "gpio"; + bias-disable; + }; +};arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +144
-0@@ -0,0 +1,616 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "talos.dtsi" +#include "pm8150.dtsi" +/ { + aliases { + mmc0 = &sdhc_1; + serial0 = &uart0; + serial1 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + clocks { + can_osc: can-oscillator { + compatible = "fixed-clock"; + clock-frequency = <20000000>; + #clock-cells = <0>; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32764>; + #clock-cells = <0>; + }; + + xo_board_clk: xo-board-clk { + compatible = "fixed-clock"; + clock-frequency = <38400000>; + #clock-cells = <0>; + }; + }; + + regulator-usb2-vbus { + compatible = "regulator-fixed"; + regulator-name = "USB2_VBUS"; + gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&usb2_en>; + pinctrl-names = "default"; + enable-active-high; + regulator-always-on; + }; + + vreg_conn_1p8: regulator-conn-1p8 { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_1p8"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 1 GPIO_ACTIVE_HIGH>; + }; + + vreg_conn_pa: regulator-conn-pa { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_pa"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 6 GPIO_ACTIVE_HIGH>; + }; + + vreg_v3p3_can: regulator-v3p3-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v3p3-can"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v5p0_can: regulator-v5p0-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v5p0-can"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + wcn6855-pmu { + compatible = "qcom,wcn6855-pmu"; + + pinctrl-0 = <&bt_en_state>, <&wlan_en_state>; + pinctrl-names = "default"; + + bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; + wlan-enable-gpios = <&tlmm 84 GPIO_ACTIVE_HIGH>; + + vddio-supply = <&vreg_conn_pa>; + vddaon-supply = <&vreg_s5a>; + vddpmu-supply = <&vreg_conn_1p8>; + vddpmumx-supply = <&vreg_conn_1p8>; + vddpmucx-supply = <&vreg_conn_pa>; + vddrfa0p95-supply = <&vreg_s5a>; + vddrfa1p3-supply = <&vreg_s6a>; + vddrfa1p9-supply = <&vreg_l15a>; + vddpcie1p3-supply = <&vreg_s6a>; + vddpcie1p9-supply = <&vreg_l15a>; + + regulators { + vreg_pmu_rfa_cmn: ldo0 { + regulator-name = "vreg_pmu_rfa_cmn"; + }; + + vreg_pmu_aon_0p59: ldo1 { + regulator-name = "vreg_pmu_aon_0p59"; + }; + + vreg_pmu_wlcx_0p8: ldo2 { + regulator-name = "vreg_pmu_wlcx_0p8"; + }; + + vreg_pmu_wlmx_0p85: ldo3 { + regulator-name = "vreg_pmu_wlmx_0p85"; + }; + + vreg_pmu_btcmx_0p85: ldo4 { + regulator-name = "vreg_pmu_btcmx_0p85"; + }; + + vreg_pmu_rfa_0p8: ldo5 { + regulator-name = "vreg_pmu_rfa_0p8"; + }; + + vreg_pmu_rfa_1p2: ldo6 { + regulator-name = "vreg_pmu_rfa_1p2"; + }; + + vreg_pmu_rfa_1p7: ldo7 { + regulator-name = "vreg_pmu_rfa_1p7"; + }; + + vreg_pmu_pcie_0p9: ldo8 { + regulator-name = "vreg_pmu_pcie_0p9"; + }; + + vreg_pmu_pcie_1p8: ldo9 { + regulator-name = "vreg_pmu_pcie_1p8";arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 154
Quoted 10 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +10
-0+ }; + }; + }; + + wifi_1p8v: regulator-wifi-1p8v { + compatible = "regulator-fixed"; + regulator-name = "wifi_1p8v"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;Please check this pin number
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 167
Quoted 13 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +13
-0+ enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; + + wifi_3p85v: regulator-wifi-3p85v { + compatible = "regulator-fixed"; + regulator-name = "wifi_3p85v"; + regulator-min-microvolt = <3850000>; + regulator-max-microvolt = <3850000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;Please check this pin number
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 173
Quoted 7 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +7
-0+ enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; +};Quoted 2 lines
Are these two node necessary?
On this board, GPIO91 is wired as a common enable for both WiFi power rails: WiFi 1.8V and WiFi 3.85V.
I currently modeled them as two regulator-fixed nodes because these are two distinct rails.
Would you prefer modelling a single regulator node that controls the shared GPIO as below:
Quoted 10 lines
wifi_en: regulator-wifi-en {
compatible = "regulator-fixed";
regulator-name = "wifi_en";
gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;
enable-active-high;
pinctrl-0 = <&wifi_reg_en_pins_state>;
pinctrl-names = "default";
regulator-boot-on;
regulator-always-on;
};What is the voltage of this regulator? What does it represent? What should be represented in the DT?
BTW: what is powered on by those regulators? I don't see them being wired to the PMU.
Signature · 2 lines
With best wishes Dmitry
Re: [PATCH v11 4/4] arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board
Quoted 396 lines · Dmitry Baryshkov
Quoted 384 lines · On Fri, Jan 16, 2026 at 12:28:22PM +0530, [email protected] wrote:
Quoted 371 lines · Qian Zhang
Quoted 335 lines · Sudarshan Shetty
Add the device tree for the QCS615-based Talos EVK platform. The platform is composed of a System-on-Module following the SMARC standard, and a Carrier Board.
The Carrier Board supports several display configurations, HDMI and LVDS. Both configurations use the same base hardware, with the display selection controlled by a DIP switch.
Use a DTBO file, talos-evk-lvds-auo,g133han01.dtso, which defines an overlay that disables HDMI and adds LVDS. The DTs file talos-evk can describe the HDMI display configurations.
The initial device tree includes support for:
- CPU and memory
- UART
- GPIOs
- Regulators
- PMIC
- Early console
- AT24MAC602 EEPROM
- MCP2515 SPI to CAN
- ADV7535 DSI-to-HDMI bridge
- DisplayPort interface
- SN65DSI84ZXHR DSI-to-LVDS bridge
- Wi-Fi/BTReviewed-by Dmitry Baryshkov <[email protected]>Signed-off-by Sudarshan Shetty <[email protected]>---
arch/arm64/boot/dts/qcom/Makefile | 4 + .../qcom/talos-evk-lvds-auo,g133han01.dtso | 126 ++++ arch/arm64/boot/dts/qcom/talos-evk-som.dtsi | 616 ++++++++++++++++++ arch/arm64/boot/dts/qcom/talos-evk.dts | 139 ++++4 files changed, 885 insertions(+)create mode 100644
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtsocreate mode 100644arch/arm64/boot/dts/qcom/talos-evk-som.dtsicreate mode 100644arch/arm64/boot/dts/qcom/talos-evk.dtsarch/arm64/boot/dts/qcom/Makefile +0
-0@@ -324,6 +324,10 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtbdtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-qrd.dtbarch/arm64/boot/dts/qcom/Makefile +4
-0+dtb-$(CONFIG_ARCH_QCOM) += talos-evk.dtb +talos-evk-lvds-auo,g133han01-dtbs := \ + talos-evk.dtb talos-evk-lvds-auo,g133han01.dtbo +dtb-$(CONFIG_ARCH_QCOM) += talos-evk-lvds-auo,g133han01.dtbx1e001de-devkit-el2-dtbs := x1e001de-devkit.dtb x1-el2.dtbo dtb-$(CONFIG_ARCH_QCOM) += x1e001de-devkit.dtb x1e001de-devkit-el2.dtb x1e78100-lenovo-thinkpad-t14s-el2-dtbs := x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso new file +126
-0@@ -0,0 +1,126 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; +/plugin/; + +#include <dt-bindings/gpio/gpio.h> + +&{/} { + backlight: backlight { + compatible = "gpio-backlight"; + gpios = <&tlmm 59 GPIO_ACTIVE_HIGH>, + <&tlmm 115 GPIO_ACTIVE_HIGH>; + default-on; + }; + + panel-lvds { + compatible = "auo,g133han01"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* LVDS A (Odd pixels) */ + port@0 { + reg = <0>; + dual-lvds-odd-pixels; + + lvds_panel_out_a: endpoint { + remote-endpoint = <&sn65dsi84_out_a>; + }; + }; + + /* LVDS B (Even pixels) */ + port@1 { + reg = <1>; + dual-lvds-even-pixels; + + lvds_panel_out_b: endpoint { + remote-endpoint = <&sn65dsi84_out_b>; + }; + }; + }; + }; +}; + +&hdmi_connector { + status = "disabled"; +}; + +&i2c1 { + clock-frequency = <400000>; + + status = "okay"; + + hdmi_bridge: bridge@3d { + status = "disabled"; + }; + + lvds_bridge: bridge@2c { + compatible = "ti,sn65dsi84"; + reg = <0x2c>; + enable-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; + ti,dsi-lanes = <4>; + ti,lvds-format = "jeida-24"; + ti,lvds-bpp = <24>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + sn65dsi84_in: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@2 { + reg = <2>; + + sn65dsi84_out_a: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_a>; + }; + }; + + port@3 { + reg = <3>; + + sn65dsi84_out_b: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_b>; + }; + }; + }; + }; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l11a>; + + status = "okay"; +}; + +&mdss_dsi0_out { + remote-endpoint = <&sn65dsi84_in>; + data-lanes = <0 1 2 3>; +}; + +&tlmm { + lcd_bklt_en: lcd-bklt-en-state { + pins = "gpio115"; + function = "gpio"; + bias-disable; + }; + + lcd_bklt_pwm: lcd-bklt-pwm-state { + pins = "gpio59"; + function = "gpio"; + bias-disable; + }; +};arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +144
-0@@ -0,0 +1,616 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "talos.dtsi" +#include "pm8150.dtsi" +/ { + aliases { + mmc0 = &sdhc_1; + serial0 = &uart0; + serial1 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + clocks { + can_osc: can-oscillator { + compatible = "fixed-clock"; + clock-frequency = <20000000>; + #clock-cells = <0>; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32764>; + #clock-cells = <0>; + }; + + xo_board_clk: xo-board-clk { + compatible = "fixed-clock"; + clock-frequency = <38400000>; + #clock-cells = <0>; + }; + }; + + regulator-usb2-vbus { + compatible = "regulator-fixed"; + regulator-name = "USB2_VBUS"; + gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&usb2_en>; + pinctrl-names = "default"; + enable-active-high; + regulator-always-on; + }; + + vreg_conn_1p8: regulator-conn-1p8 { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_1p8"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 1 GPIO_ACTIVE_HIGH>; + }; + + vreg_conn_pa: regulator-conn-pa { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_pa"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 6 GPIO_ACTIVE_HIGH>; + }; + + vreg_v3p3_can: regulator-v3p3-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v3p3-can"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v5p0_can: regulator-v5p0-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v5p0-can"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + wcn6855-pmu { + compatible = "qcom,wcn6855-pmu"; + + pinctrl-0 = <&bt_en_state>, <&wlan_en_state>; + pinctrl-names = "default"; + + bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; + wlan-enable-gpios = <&tlmm 84 GPIO_ACTIVE_HIGH>; + + vddio-supply = <&vreg_conn_pa>; + vddaon-supply = <&vreg_s5a>; + vddpmu-supply = <&vreg_conn_1p8>; + vddpmumx-supply = <&vreg_conn_1p8>; + vddpmucx-supply = <&vreg_conn_pa>; + vddrfa0p95-supply = <&vreg_s5a>; + vddrfa1p3-supply = <&vreg_s6a>; + vddrfa1p9-supply = <&vreg_l15a>; + vddpcie1p3-supply = <&vreg_s6a>; + vddpcie1p9-supply = <&vreg_l15a>; + + regulators { + vreg_pmu_rfa_cmn: ldo0 { + regulator-name = "vreg_pmu_rfa_cmn"; + }; + + vreg_pmu_aon_0p59: ldo1 { + regulator-name = "vreg_pmu_aon_0p59"; + }; + + vreg_pmu_wlcx_0p8: ldo2 { + regulator-name = "vreg_pmu_wlcx_0p8"; + }; + + vreg_pmu_wlmx_0p85: ldo3 { + regulator-name = "vreg_pmu_wlmx_0p85"; + }; + + vreg_pmu_btcmx_0p85: ldo4 { + regulator-name = "vreg_pmu_btcmx_0p85"; + }; + + vreg_pmu_rfa_0p8: ldo5 { + regulator-name = "vreg_pmu_rfa_0p8"; + }; + + vreg_pmu_rfa_1p2: ldo6 { + regulator-name = "vreg_pmu_rfa_1p2"; + }; + + vreg_pmu_rfa_1p7: ldo7 { + regulator-name = "vreg_pmu_rfa_1p7"; + }; + + vreg_pmu_pcie_0p9: ldo8 { + regulator-name = "vreg_pmu_pcie_0p9"; + }; + + vreg_pmu_pcie_1p8: ldo9 { + regulator-name = "vreg_pmu_pcie_1p8";arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 154
Quoted 10 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +10
-0+ }; + }; + }; + + wifi_1p8v: regulator-wifi-1p8v { + compatible = "regulator-fixed"; + regulator-name = "wifi_1p8v"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;Please check this pin number
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 167
Quoted 13 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +13
-0+ enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; + + wifi_3p85v: regulator-wifi-3p85v { + compatible = "regulator-fixed"; + regulator-name = "wifi_3p85v"; + regulator-min-microvolt = <3850000>; + regulator-max-microvolt = <3850000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;Please check this pin number
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 173
Quoted 7 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +7
-0+ enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; +};Quoted 2 lines
Are these two node necessary?
On this board, GPIO91 is wired as a common enable for both WiFi power rails: WiFi 1.8V and WiFi 3.85V.
I currently modeled them as two regulator-fixed nodes because these are two distinct rails.
Would you prefer modelling a single regulator node that controls the shared GPIO as below:Quoted 10 lines
wifi_en: regulator-wifi-en { compatible = "regulator-fixed"; regulator-name = "wifi_en"; gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>; enable-active-high; pinctrl-0 = <&wifi_reg_en_pins_state>; pinctrl-names = "default"; regulator-boot-on; regulator-always-on; };
Quoted 6 lines
What is the voltage of this regulator? What does it represent? What should be represented in the DT?
BTW: what is powered on by those regulators? I don't see them being wired to the PMU.
There are two separate TPS62130RGTR regulator ICs on the board:
One provides 1.8V and Another provides 3.85V.
Both regulators use the same enable signal (SOC_GPIO_91_S4A_1P8 - GPIO91), which connects to their EN pins.
When GPIO91 goes high, both regulators switch on at the same time.
I described them as two separate regulator-fixed nodes since they are different chips with different voltages.
As an alternative, I suggested representing them as a single node (based on the review comment from Qian Zhang) if you only want to show the shared GPIO enable control instead of the individual voltage rails.
In AF68E module, 3.85V regulator powers VDD_PA_5G and 1.8V regulator powers VDD_PA_2G.
Re: [PATCH v11 4/4] arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board
Quoted 406 lines · On Fri, Jan 16, 2026 at 04:57:42PM +0530, [email protected] wrote:
Quoted 396 lines · Dmitry Baryshkov
Quoted 384 lines · On Fri, Jan 16, 2026 at 12:28:22PM +0530, [email protected] wrote:
Quoted 371 lines · Qian Zhang
Quoted 335 lines · Sudarshan Shetty
Add the device tree for the QCS615-based Talos EVK platform. The platform is composed of a System-on-Module following the SMARC standard, and a Carrier Board.
The Carrier Board supports several display configurations, HDMI and LVDS. Both configurations use the same base hardware, with the display selection controlled by a DIP switch.
Use a DTBO file, talos-evk-lvds-auo,g133han01.dtso, which defines an overlay that disables HDMI and adds LVDS. The DTs file talos-evk can describe the HDMI display configurations.
The initial device tree includes support for:
- CPU and memory
- UART
- GPIOs
- Regulators
- PMIC
- Early console
- AT24MAC602 EEPROM
- MCP2515 SPI to CAN
- ADV7535 DSI-to-HDMI bridge
- DisplayPort interface
- SN65DSI84ZXHR DSI-to-LVDS bridge
- Wi-Fi/BTReviewed-by Dmitry Baryshkov <[email protected]>Signed-off-by Sudarshan Shetty <[email protected]>---
arch/arm64/boot/dts/qcom/Makefile | 4 + .../qcom/talos-evk-lvds-auo,g133han01.dtso | 126 ++++ arch/arm64/boot/dts/qcom/talos-evk-som.dtsi | 616 ++++++++++++++++++ arch/arm64/boot/dts/qcom/talos-evk.dts | 139 ++++4 files changed, 885 insertions(+)create mode 100644
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtsocreate mode 100644arch/arm64/boot/dts/qcom/talos-evk-som.dtsicreate mode 100644arch/arm64/boot/dts/qcom/talos-evk.dtsarch/arm64/boot/dts/qcom/Makefile +0
-0@@ -324,6 +324,10 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtbdtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-qrd.dtbarch/arm64/boot/dts/qcom/Makefile +4
-0+dtb-$(CONFIG_ARCH_QCOM) += talos-evk.dtb +talos-evk-lvds-auo,g133han01-dtbs := \ + talos-evk.dtb talos-evk-lvds-auo,g133han01.dtbo +dtb-$(CONFIG_ARCH_QCOM) += talos-evk-lvds-auo,g133han01.dtbx1e001de-devkit-el2-dtbs := x1e001de-devkit.dtb x1-el2.dtbo dtb-$(CONFIG_ARCH_QCOM) += x1e001de-devkit.dtb x1e001de-devkit-el2.dtb x1e78100-lenovo-thinkpad-t14s-el2-dtbs := x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso new file +126
-0@@ -0,0 +1,126 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; +/plugin/; + +#include <dt-bindings/gpio/gpio.h> + +&{/} { + backlight: backlight { + compatible = "gpio-backlight"; + gpios = <&tlmm 59 GPIO_ACTIVE_HIGH>, + <&tlmm 115 GPIO_ACTIVE_HIGH>; + default-on; + }; + + panel-lvds { + compatible = "auo,g133han01"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* LVDS A (Odd pixels) */ + port@0 { + reg = <0>; + dual-lvds-odd-pixels; + + lvds_panel_out_a: endpoint { + remote-endpoint = <&sn65dsi84_out_a>; + }; + }; + + /* LVDS B (Even pixels) */ + port@1 { + reg = <1>; + dual-lvds-even-pixels; + + lvds_panel_out_b: endpoint { + remote-endpoint = <&sn65dsi84_out_b>; + }; + }; + }; + }; +}; + +&hdmi_connector { + status = "disabled"; +}; + +&i2c1 { + clock-frequency = <400000>; + + status = "okay"; + + hdmi_bridge: bridge@3d { + status = "disabled"; + }; + + lvds_bridge: bridge@2c { + compatible = "ti,sn65dsi84"; + reg = <0x2c>; + enable-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; + ti,dsi-lanes = <4>; + ti,lvds-format = "jeida-24"; + ti,lvds-bpp = <24>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + sn65dsi84_in: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@2 { + reg = <2>; + + sn65dsi84_out_a: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_a>; + }; + }; + + port@3 { + reg = <3>; + + sn65dsi84_out_b: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_b>; + }; + }; + }; + }; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l11a>; + + status = "okay"; +}; + +&mdss_dsi0_out { + remote-endpoint = <&sn65dsi84_in>; + data-lanes = <0 1 2 3>; +}; + +&tlmm { + lcd_bklt_en: lcd-bklt-en-state { + pins = "gpio115"; + function = "gpio"; + bias-disable; + }; + + lcd_bklt_pwm: lcd-bklt-pwm-state { + pins = "gpio59"; + function = "gpio"; + bias-disable; + }; +};arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +144
-0@@ -0,0 +1,616 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "talos.dtsi" +#include "pm8150.dtsi" +/ { + aliases { + mmc0 = &sdhc_1; + serial0 = &uart0; + serial1 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + clocks { + can_osc: can-oscillator { + compatible = "fixed-clock"; + clock-frequency = <20000000>; + #clock-cells = <0>; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32764>; + #clock-cells = <0>; + }; + + xo_board_clk: xo-board-clk { + compatible = "fixed-clock"; + clock-frequency = <38400000>; + #clock-cells = <0>; + }; + }; + + regulator-usb2-vbus { + compatible = "regulator-fixed"; + regulator-name = "USB2_VBUS"; + gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&usb2_en>; + pinctrl-names = "default"; + enable-active-high; + regulator-always-on; + }; + + vreg_conn_1p8: regulator-conn-1p8 { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_1p8"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 1 GPIO_ACTIVE_HIGH>; + }; + + vreg_conn_pa: regulator-conn-pa { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_pa"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 6 GPIO_ACTIVE_HIGH>; + }; + + vreg_v3p3_can: regulator-v3p3-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v3p3-can"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v5p0_can: regulator-v5p0-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v5p0-can"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + wcn6855-pmu { + compatible = "qcom,wcn6855-pmu"; + + pinctrl-0 = <&bt_en_state>, <&wlan_en_state>; + pinctrl-names = "default"; + + bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; + wlan-enable-gpios = <&tlmm 84 GPIO_ACTIVE_HIGH>; + + vddio-supply = <&vreg_conn_pa>; + vddaon-supply = <&vreg_s5a>; + vddpmu-supply = <&vreg_conn_1p8>; + vddpmumx-supply = <&vreg_conn_1p8>; + vddpmucx-supply = <&vreg_conn_pa>; + vddrfa0p95-supply = <&vreg_s5a>; + vddrfa1p3-supply = <&vreg_s6a>; + vddrfa1p9-supply = <&vreg_l15a>; + vddpcie1p3-supply = <&vreg_s6a>; + vddpcie1p9-supply = <&vreg_l15a>; + + regulators { + vreg_pmu_rfa_cmn: ldo0 { + regulator-name = "vreg_pmu_rfa_cmn"; + }; + + vreg_pmu_aon_0p59: ldo1 { + regulator-name = "vreg_pmu_aon_0p59"; + }; + + vreg_pmu_wlcx_0p8: ldo2 { + regulator-name = "vreg_pmu_wlcx_0p8"; + }; + + vreg_pmu_wlmx_0p85: ldo3 { + regulator-name = "vreg_pmu_wlmx_0p85"; + }; + + vreg_pmu_btcmx_0p85: ldo4 { + regulator-name = "vreg_pmu_btcmx_0p85"; + }; + + vreg_pmu_rfa_0p8: ldo5 { + regulator-name = "vreg_pmu_rfa_0p8"; + }; + + vreg_pmu_rfa_1p2: ldo6 { + regulator-name = "vreg_pmu_rfa_1p2"; + }; + + vreg_pmu_rfa_1p7: ldo7 { + regulator-name = "vreg_pmu_rfa_1p7"; + }; + + vreg_pmu_pcie_0p9: ldo8 { + regulator-name = "vreg_pmu_pcie_0p9"; + }; + + vreg_pmu_pcie_1p8: ldo9 { + regulator-name = "vreg_pmu_pcie_1p8";arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 154
Quoted 10 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +10
-0+ }; + }; + }; + + wifi_1p8v: regulator-wifi-1p8v { + compatible = "regulator-fixed"; + regulator-name = "wifi_1p8v"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;Please check this pin number
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 167
Quoted 13 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +13
-0+ enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; + + wifi_3p85v: regulator-wifi-3p85v { + compatible = "regulator-fixed"; + regulator-name = "wifi_3p85v"; + regulator-min-microvolt = <3850000>; + regulator-max-microvolt = <3850000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;Please check this pin number
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 173
Quoted 7 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +7
-0+ enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; +};Quoted 2 lines
Are these two node necessary?
On this board, GPIO91 is wired as a common enable for both WiFi power rails: WiFi 1.8V and WiFi 3.85V.
I currently modeled them as two regulator-fixed nodes because these are two distinct rails.
Would you prefer modelling a single regulator node that controls the shared GPIO as below:Quoted 10 lines
wifi_en: regulator-wifi-en { compatible = "regulator-fixed"; regulator-name = "wifi_en"; gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>; enable-active-high; pinctrl-0 = <&wifi_reg_en_pins_state>; pinctrl-names = "default"; regulator-boot-on; regulator-always-on; };Quoted 6 lines
What is the voltage of this regulator? What does it represent? What should be represented in the DT?
BTW: what is powered on by those regulators? I don't see them being wired to the PMU.
Quoted 7 lines
There are two separate TPS62130RGTR regulator ICs on the board:
One provides 1.8V and Another provides 3.85V.Both regulators use the same enable signal (
SOC_GPIO_91_S4A_1P8- GPIO91), which connects to their EN pins.
When GPIO91 goes high, both regulators switch on at the same time.
And gpiolib-shared.c should be able to support that.
Quoted 3 lines
I described them as two separate regulator-fixed nodes since they are different chips with different voltages.
okay.
Quoted 5 lines
As an alternative, I suggested representing them as a single node (based on the review comment from Qian Zhang) if you only want to show the shared GPIO enable control instead of the individual voltage rails.
Why do you need an alternative?
Quoted 3 lines
In AF68E module, 3.85V regulator powers
VDD_PA_5Gand 1.8V regulator powersVDD_PA_2G.
Do they power up the WCN6855 itself or some external PA present on the module? In the former case, those regulators should be consumed by the PMU, in the latter case, by the WiFi node. Anyway, they should not be left as always-on / boot-on.
Signature · 2 lines
With best wishes Dmitry
Re: [PATCH v11 4/4] arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board
Quoted 432 lines · Dmitry Baryshkov
Quoted 406 lines · On Fri, Jan 16, 2026 at 04:57:42PM +0530, [email protected] wrote:
Quoted 396 lines · Dmitry Baryshkov
Quoted 384 lines · On Fri, Jan 16, 2026 at 12:28:22PM +0530, [email protected] wrote:
Quoted 371 lines · Qian Zhang
Quoted 335 lines · Sudarshan Shetty
Add the device tree for the QCS615-based Talos EVK platform. The platform is composed of a System-on-Module following the SMARC standard, and a Carrier Board.
The Carrier Board supports several display configurations, HDMI and LVDS. Both configurations use the same base hardware, with the display selection controlled by a DIP switch.
Use a DTBO file, talos-evk-lvds-auo,g133han01.dtso, which defines an overlay that disables HDMI and adds LVDS. The DTs file talos-evk can describe the HDMI display configurations.
The initial device tree includes support for:
- CPU and memory
- UART
- GPIOs
- Regulators
- PMIC
- Early console
- AT24MAC602 EEPROM
- MCP2515 SPI to CAN
- ADV7535 DSI-to-HDMI bridge
- DisplayPort interface
- SN65DSI84ZXHR DSI-to-LVDS bridge
- Wi-Fi/BTReviewed-by Dmitry Baryshkov <[email protected]>Signed-off-by Sudarshan Shetty <[email protected]>---
arch/arm64/boot/dts/qcom/Makefile | 4 + .../qcom/talos-evk-lvds-auo,g133han01.dtso | 126 ++++ arch/arm64/boot/dts/qcom/talos-evk-som.dtsi | 616 ++++++++++++++++++ arch/arm64/boot/dts/qcom/talos-evk.dts | 139 ++++4 files changed, 885 insertions(+)create mode 100644
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtsocreate mode 100644arch/arm64/boot/dts/qcom/talos-evk-som.dtsicreate mode 100644arch/arm64/boot/dts/qcom/talos-evk.dtsarch/arm64/boot/dts/qcom/Makefile +0
-0@@ -324,6 +324,10 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtbdtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-qrd.dtbarch/arm64/boot/dts/qcom/Makefile +4
-0+dtb-$(CONFIG_ARCH_QCOM) += talos-evk.dtb +talos-evk-lvds-auo,g133han01-dtbs := \ + talos-evk.dtb talos-evk-lvds-auo,g133han01.dtbo +dtb-$(CONFIG_ARCH_QCOM) += talos-evk-lvds-auo,g133han01.dtbx1e001de-devkit-el2-dtbs := x1e001de-devkit.dtb x1-el2.dtbo dtb-$(CONFIG_ARCH_QCOM) += x1e001de-devkit.dtb x1e001de-devkit-el2.dtb x1e78100-lenovo-thinkpad-t14s-el2-dtbs := x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso new file +126
-0@@ -0,0 +1,126 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; +/plugin/; + +#include <dt-bindings/gpio/gpio.h> + +&{/} { + backlight: backlight { + compatible = "gpio-backlight"; + gpios = <&tlmm 59 GPIO_ACTIVE_HIGH>, + <&tlmm 115 GPIO_ACTIVE_HIGH>; + default-on; + }; + + panel-lvds { + compatible = "auo,g133han01"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* LVDS A (Odd pixels) */ + port@0 { + reg = <0>; + dual-lvds-odd-pixels; + + lvds_panel_out_a: endpoint { + remote-endpoint = <&sn65dsi84_out_a>; + }; + }; + + /* LVDS B (Even pixels) */ + port@1 { + reg = <1>; + dual-lvds-even-pixels; + + lvds_panel_out_b: endpoint { + remote-endpoint = <&sn65dsi84_out_b>; + }; + }; + }; + }; +}; + +&hdmi_connector { + status = "disabled"; +}; + +&i2c1 { + clock-frequency = <400000>; + + status = "okay"; + + hdmi_bridge: bridge@3d { + status = "disabled"; + }; + + lvds_bridge: bridge@2c { + compatible = "ti,sn65dsi84"; + reg = <0x2c>; + enable-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; + ti,dsi-lanes = <4>; + ti,lvds-format = "jeida-24"; + ti,lvds-bpp = <24>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + sn65dsi84_in: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@2 { + reg = <2>; + + sn65dsi84_out_a: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_a>; + }; + }; + + port@3 { + reg = <3>; + + sn65dsi84_out_b: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_b>; + }; + }; + }; + }; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l11a>; + + status = "okay"; +}; + +&mdss_dsi0_out { + remote-endpoint = <&sn65dsi84_in>; + data-lanes = <0 1 2 3>; +}; + +&tlmm { + lcd_bklt_en: lcd-bklt-en-state { + pins = "gpio115"; + function = "gpio"; + bias-disable; + }; + + lcd_bklt_pwm: lcd-bklt-pwm-state { + pins = "gpio59"; + function = "gpio"; + bias-disable; + }; +};arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +144
-0@@ -0,0 +1,616 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "talos.dtsi" +#include "pm8150.dtsi" +/ { + aliases { + mmc0 = &sdhc_1; + serial0 = &uart0; + serial1 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + clocks { + can_osc: can-oscillator { + compatible = "fixed-clock"; + clock-frequency = <20000000>; + #clock-cells = <0>; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32764>; + #clock-cells = <0>; + }; + + xo_board_clk: xo-board-clk { + compatible = "fixed-clock"; + clock-frequency = <38400000>; + #clock-cells = <0>; + }; + }; + + regulator-usb2-vbus { + compatible = "regulator-fixed"; + regulator-name = "USB2_VBUS"; + gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&usb2_en>; + pinctrl-names = "default"; + enable-active-high; + regulator-always-on; + }; + + vreg_conn_1p8: regulator-conn-1p8 { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_1p8"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 1 GPIO_ACTIVE_HIGH>; + }; + + vreg_conn_pa: regulator-conn-pa { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_pa"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 6 GPIO_ACTIVE_HIGH>; + }; + + vreg_v3p3_can: regulator-v3p3-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v3p3-can"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v5p0_can: regulator-v5p0-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v5p0-can"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + wcn6855-pmu { + compatible = "qcom,wcn6855-pmu"; + + pinctrl-0 = <&bt_en_state>, <&wlan_en_state>; + pinctrl-names = "default"; + + bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; + wlan-enable-gpios = <&tlmm 84 GPIO_ACTIVE_HIGH>; + + vddio-supply = <&vreg_conn_pa>; + vddaon-supply = <&vreg_s5a>; + vddpmu-supply = <&vreg_conn_1p8>; + vddpmumx-supply = <&vreg_conn_1p8>; + vddpmucx-supply = <&vreg_conn_pa>; + vddrfa0p95-supply = <&vreg_s5a>; + vddrfa1p3-supply = <&vreg_s6a>; + vddrfa1p9-supply = <&vreg_l15a>; + vddpcie1p3-supply = <&vreg_s6a>; + vddpcie1p9-supply = <&vreg_l15a>; + + regulators { + vreg_pmu_rfa_cmn: ldo0 { + regulator-name = "vreg_pmu_rfa_cmn"; + }; + + vreg_pmu_aon_0p59: ldo1 { + regulator-name = "vreg_pmu_aon_0p59"; + }; + + vreg_pmu_wlcx_0p8: ldo2 { + regulator-name = "vreg_pmu_wlcx_0p8"; + }; + + vreg_pmu_wlmx_0p85: ldo3 { + regulator-name = "vreg_pmu_wlmx_0p85"; + }; + + vreg_pmu_btcmx_0p85: ldo4 { + regulator-name = "vreg_pmu_btcmx_0p85"; + }; + + vreg_pmu_rfa_0p8: ldo5 { + regulator-name = "vreg_pmu_rfa_0p8"; + }; + + vreg_pmu_rfa_1p2: ldo6 { + regulator-name = "vreg_pmu_rfa_1p2"; + }; + + vreg_pmu_rfa_1p7: ldo7 { + regulator-name = "vreg_pmu_rfa_1p7"; + }; + + vreg_pmu_pcie_0p9: ldo8 { + regulator-name = "vreg_pmu_pcie_0p9"; + }; + + vreg_pmu_pcie_1p8: ldo9 { + regulator-name = "vreg_pmu_pcie_1p8";arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 154
Quoted 10 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +10
-0+ }; + }; + }; + + wifi_1p8v: regulator-wifi-1p8v { + compatible = "regulator-fixed"; + regulator-name = "wifi_1p8v"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;Please check this pin number
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 167
Quoted 13 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +13
-0+ enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; + + wifi_3p85v: regulator-wifi-3p85v { + compatible = "regulator-fixed"; + regulator-name = "wifi_3p85v"; + regulator-min-microvolt = <3850000>; + regulator-max-microvolt = <3850000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;Please check this pin number
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 174
Quoted 7 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +7
-0+ enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; +};Quoted 2 lines
Are these two node necessary?
On this board, GPIO91 is wired as a common enable for both WiFi power rails: WiFi 1.8V and WiFi 3.85V.
I currently modeled them as two regulator-fixed nodes because these are two distinct rails.
Would you prefer modelling a single regulator node that controls the shared GPIO as below:Quoted 10 lines
wifi_en: regulator-wifi-en { compatible = "regulator-fixed"; regulator-name = "wifi_en"; gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>; enable-active-high; pinctrl-0 = <&wifi_reg_en_pins_state>; pinctrl-names = "default"; regulator-boot-on; regulator-always-on; };Quoted 6 lines
What is the voltage of this regulator? What does it represent? What should be represented in the DT?
BTW: what is powered on by those regulators? I don't see them being wired to the PMU.
Quoted 7 lines
There are two separate TPS62130RGTR regulator ICs on the board:
One provides 1.8V and Another provides 3.85V.Both regulators use the same enable signal (
SOC_GPIO_91_S4A_1P8- GPIO91), which connects to their EN pins.
When GPIO91 goes high, both regulators switch on at the same time.And
gpiolib-shared.cshould be able to support that.Quoted 3 lines
I described them as two separate regulator-fixed nodes since they are different chips with different voltages.
okay.
Quoted 5 lines
As an alternative, I suggested representing them as a single node (based on the review comment from Qian Zhang) if you only want to show the shared GPIO enable control instead of the individual voltage rails.
Why do you need an alternative?
Quoted 1 line
Quoted 8 lines
Quoted 2 lines
In AF68E module, 3.85V regulator powers
VDD_PA_5Gand 1.8V regulator powersVDD_PA_2G.Do they power up the WCN6855 itself or some external PA present on the module? In the former case, those regulators should be consumed by the PMU, in the latter case, by the WiFi node. Anyway, they should not be left as always-on / boot-on.
On this board, the GPIO-controlled regulators power the WCN6855 WiFi module itself (not an external PA). To model this correctly, I updated the device tree like this:
a) I added a single upstream fixed regulator, wifi_vin, which represents the GPIO enable line (tlmm 91). This is the only node marked always-on, so the enable GPIO stays asserted.
b) The downstream rails wifi_1p8v and wifi_3p85v are now defined as fixed regulators that depend on wifi_vin using vin-supply. They no longer control the GPIO directly.
c) These two rails are then explicitly connected as supplies to the WiFi device node (wifi@0) using:
1. vddpaa-supply = <&wifi_3p85v>;
2. vddpab-supply = <&wifi_1p8v>;
With this change, the regulators are not left as generic always-on/ boot-on supplies without a consumer. Instead, the WiFi device node consumes the rails, which matches the real hardware wiring: the GPIO enables power to the WCN6855 rails.
Please find the updated changes below - could you please confirm whether this aligns with your expectations?
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi +25 -10
@@ -146,29 +146,41 @@ vreg_pmu_pcie_1p8: ldo9 { }; }; - wifi_1p8v: regulator-wifi-1p8v { + /* Downstream rails controlled by the same GPIO */ + wifi_1p8v: regulator-1p8v { compatible = "regulator-fixed"; + regulator-name = "wifi_1p8v"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>; - enable-active-high; - pinctrl-0 = <&wifi_reg_en_pins_state>; - pinctrl-names = "default"; - regulator-boot-on; - regulator-always-on; + + vin-supply = <&wifi_vin>; }; - wifi_3p85v: regulator-wifi-3p85v { + wifi_3p85v: regulator-3p85v { compatible = "regulator-fixed"; + regulator-name = "wifi_3p85v"; regulator-min-microvolt = <3850000>; regulator-max-microvolt = <3850000>; - gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>; + + vin-supply = <&wifi_vin>; + }; + + /* Upstream supply */ + wifi_vin: regulator-wifi-en { + compatible = "regulator-fixed"; + + regulator-name = "wifi_vin"; + regulator-min-microvolt = <3850000>; + regulator-max-microvolt = <3850000>; + enable-active-high; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&wifi_reg_en_pins_state>; pinctrl-names = "default"; - regulator-boot-on; + regulator-always-on; }; };
@@ -413,6 +425,9 @@ wifi@0 { vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>; vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>; vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>; + vddpaa-supply = <&wifi_3p85v>; + vddpab-supply = <&wifi_1p8v>; + }; };
Re: [PATCH v11 4/4] arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board
Quoted 444 lines · On Tue, Jan 20, 2026 at 04:33:28PM +0530, [email protected] wrote:
Quoted 432 lines · Dmitry Baryshkov
Quoted 406 lines · On Fri, Jan 16, 2026 at 04:57:42PM +0530, [email protected] wrote:
Quoted 396 lines · Dmitry Baryshkov
Quoted 384 lines · On Fri, Jan 16, 2026 at 12:28:22PM +0530, [email protected] wrote:
Quoted 371 lines · Qian Zhang
Quoted 335 lines · Sudarshan Shetty
Add the device tree for the QCS615-based Talos EVK platform. The platform is composed of a System-on-Module following the SMARC standard, and a Carrier Board.
The Carrier Board supports several display configurations, HDMI and LVDS. Both configurations use the same base hardware, with the display selection controlled by a DIP switch.
Use a DTBO file, talos-evk-lvds-auo,g133han01.dtso, which defines an overlay that disables HDMI and adds LVDS. The DTs file talos-evk can describe the HDMI display configurations.
The initial device tree includes support for:
- CPU and memory
- UART
- GPIOs
- Regulators
- PMIC
- Early console
- AT24MAC602 EEPROM
- MCP2515 SPI to CAN
- ADV7535 DSI-to-HDMI bridge
- DisplayPort interface
- SN65DSI84ZXHR DSI-to-LVDS bridge
- Wi-Fi/BTReviewed-by Dmitry Baryshkov <[email protected]>Signed-off-by Sudarshan Shetty <[email protected]>---
arch/arm64/boot/dts/qcom/Makefile | 4 + .../qcom/talos-evk-lvds-auo,g133han01.dtso | 126 ++++ arch/arm64/boot/dts/qcom/talos-evk-som.dtsi | 616 ++++++++++++++++++ arch/arm64/boot/dts/qcom/talos-evk.dts | 139 ++++4 files changed, 885 insertions(+)create mode 100644
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtsocreate mode 100644arch/arm64/boot/dts/qcom/talos-evk-som.dtsicreate mode 100644arch/arm64/boot/dts/qcom/talos-evk.dtsarch/arm64/boot/dts/qcom/Makefile +0
-0@@ -324,6 +324,10 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtbdtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8750-qrd.dtbarch/arm64/boot/dts/qcom/Makefile +4
-0+dtb-$(CONFIG_ARCH_QCOM) += talos-evk.dtb +talos-evk-lvds-auo,g133han01-dtbs := \ + talos-evk.dtb talos-evk-lvds-auo,g133han01.dtbo +dtb-$(CONFIG_ARCH_QCOM) += talos-evk-lvds-auo,g133han01.dtbx1e001de-devkit-el2-dtbs := x1e001de-devkit.dtb x1-el2.dtbo dtb-$(CONFIG_ARCH_QCOM) += x1e001de-devkit.dtb x1e001de-devkit-el2.dtb x1e78100-lenovo-thinkpad-t14s-el2-dtbs := x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso new file +126
-0@@ -0,0 +1,126 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; +/plugin/; + +#include <dt-bindings/gpio/gpio.h> + +&{/} { + backlight: backlight { + compatible = "gpio-backlight"; + gpios = <&tlmm 59 GPIO_ACTIVE_HIGH>, + <&tlmm 115 GPIO_ACTIVE_HIGH>; + default-on; + }; + + panel-lvds { + compatible = "auo,g133han01"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* LVDS A (Odd pixels) */ + port@0 { + reg = <0>; + dual-lvds-odd-pixels; + + lvds_panel_out_a: endpoint { + remote-endpoint = <&sn65dsi84_out_a>; + }; + }; + + /* LVDS B (Even pixels) */ + port@1 { + reg = <1>; + dual-lvds-even-pixels; + + lvds_panel_out_b: endpoint { + remote-endpoint = <&sn65dsi84_out_b>; + }; + }; + }; + }; +}; + +&hdmi_connector { + status = "disabled"; +}; + +&i2c1 { + clock-frequency = <400000>; + + status = "okay"; + + hdmi_bridge: bridge@3d { + status = "disabled"; + }; + + lvds_bridge: bridge@2c { + compatible = "ti,sn65dsi84"; + reg = <0x2c>; + enable-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; + ti,dsi-lanes = <4>; + ti,lvds-format = "jeida-24"; + ti,lvds-bpp = <24>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + sn65dsi84_in: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@2 { + reg = <2>; + + sn65dsi84_out_a: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_a>; + }; + }; + + port@3 { + reg = <3>; + + sn65dsi84_out_b: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_panel_out_b>; + }; + }; + }; + }; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l11a>; + + status = "okay"; +}; + +&mdss_dsi0_out { + remote-endpoint = <&sn65dsi84_in>; + data-lanes = <0 1 2 3>; +}; + +&tlmm { + lcd_bklt_en: lcd-bklt-en-state { + pins = "gpio115"; + function = "gpio"; + bias-disable; + }; + + lcd_bklt_pwm: lcd-bklt-pwm-state { + pins = "gpio59"; + function = "gpio"; + bias-disable; + }; +};arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +144
-0@@ -0,0 +1,616 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "talos.dtsi" +#include "pm8150.dtsi" +/ { + aliases { + mmc0 = &sdhc_1; + serial0 = &uart0; + serial1 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + clocks { + can_osc: can-oscillator { + compatible = "fixed-clock"; + clock-frequency = <20000000>; + #clock-cells = <0>; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32764>; + #clock-cells = <0>; + }; + + xo_board_clk: xo-board-clk { + compatible = "fixed-clock"; + clock-frequency = <38400000>; + #clock-cells = <0>; + }; + }; + + regulator-usb2-vbus { + compatible = "regulator-fixed"; + regulator-name = "USB2_VBUS"; + gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&usb2_en>; + pinctrl-names = "default"; + enable-active-high; + regulator-always-on; + }; + + vreg_conn_1p8: regulator-conn-1p8 { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_1p8"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 1 GPIO_ACTIVE_HIGH>; + }; + + vreg_conn_pa: regulator-conn-pa { + compatible = "regulator-fixed"; + regulator-name = "vreg_conn_pa"; + startup-delay-us = <4000>; + enable-active-high; + gpio = <&pm8150_gpios 6 GPIO_ACTIVE_HIGH>; + }; + + vreg_v3p3_can: regulator-v3p3-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v3p3-can"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vreg_v5p0_can: regulator-v5p0-can { + compatible = "regulator-fixed"; + regulator-name = "vreg-v5p0-can"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + wcn6855-pmu { + compatible = "qcom,wcn6855-pmu"; + + pinctrl-0 = <&bt_en_state>, <&wlan_en_state>; + pinctrl-names = "default"; + + bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; + wlan-enable-gpios = <&tlmm 84 GPIO_ACTIVE_HIGH>; + + vddio-supply = <&vreg_conn_pa>; + vddaon-supply = <&vreg_s5a>; + vddpmu-supply = <&vreg_conn_1p8>; + vddpmumx-supply = <&vreg_conn_1p8>; + vddpmucx-supply = <&vreg_conn_pa>; + vddrfa0p95-supply = <&vreg_s5a>; + vddrfa1p3-supply = <&vreg_s6a>; + vddrfa1p9-supply = <&vreg_l15a>; + vddpcie1p3-supply = <&vreg_s6a>; + vddpcie1p9-supply = <&vreg_l15a>; + + regulators { + vreg_pmu_rfa_cmn: ldo0 { + regulator-name = "vreg_pmu_rfa_cmn"; + }; + + vreg_pmu_aon_0p59: ldo1 { + regulator-name = "vreg_pmu_aon_0p59"; + }; + + vreg_pmu_wlcx_0p8: ldo2 { + regulator-name = "vreg_pmu_wlcx_0p8"; + }; + + vreg_pmu_wlmx_0p85: ldo3 { + regulator-name = "vreg_pmu_wlmx_0p85"; + }; + + vreg_pmu_btcmx_0p85: ldo4 { + regulator-name = "vreg_pmu_btcmx_0p85"; + }; + + vreg_pmu_rfa_0p8: ldo5 { + regulator-name = "vreg_pmu_rfa_0p8"; + }; + + vreg_pmu_rfa_1p2: ldo6 { + regulator-name = "vreg_pmu_rfa_1p2"; + }; + + vreg_pmu_rfa_1p7: ldo7 { + regulator-name = "vreg_pmu_rfa_1p7"; + }; + + vreg_pmu_pcie_0p9: ldo8 { + regulator-name = "vreg_pmu_pcie_0p9"; + }; + + vreg_pmu_pcie_1p8: ldo9 { + regulator-name = "vreg_pmu_pcie_1p8";arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 154
Quoted 10 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +10
-0+ }; + }; + }; + + wifi_1p8v: regulator-wifi-1p8v { + compatible = "regulator-fixed"; + regulator-name = "wifi_1p8v"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;Please check this pin number
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 167
Quoted 13 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +13
-0+ enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; + + wifi_3p85v: regulator-wifi-3p85v { + compatible = "regulator-fixed"; + regulator-name = "wifi_3p85v"; + regulator-min-microvolt = <3850000>; + regulator-max-microvolt = <3850000>; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;Please check this pin number
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi line 174
Quoted 7 lines
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi new file +7
-0+ enable-active-high; + pinctrl-0 = <&wifi_reg_en_pins_state>; + pinctrl-names = "default"; + regulator-boot-on; + regulator-always-on; + }; +};Quoted 2 lines
Are these two node necessary?
On this board, GPIO91 is wired as a common enable for both WiFi power rails: WiFi 1.8V and WiFi 3.85V.
I currently modeled them as two regulator-fixed nodes because these are two distinct rails.
Would you prefer modelling a single regulator node that controls the shared GPIO as below:Quoted 10 lines
wifi_en: regulator-wifi-en { compatible = "regulator-fixed"; regulator-name = "wifi_en"; gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>; enable-active-high; pinctrl-0 = <&wifi_reg_en_pins_state>; pinctrl-names = "default"; regulator-boot-on; regulator-always-on; };Quoted 6 lines
What is the voltage of this regulator? What does it represent? What should be represented in the DT?
BTW: what is powered on by those regulators? I don't see them being wired to the PMU.
Quoted 7 lines
There are two separate TPS62130RGTR regulator ICs on the board:
One provides 1.8V and Another provides 3.85V.Both regulators use the same enable signal (
SOC_GPIO_91_S4A_1P8- GPIO91), which connects to their EN pins.
When GPIO91 goes high, both regulators switch on at the same time.And
gpiolib-shared.cshould be able to support that.Quoted 3 lines
I described them as two separate regulator-fixed nodes since they are different chips with different voltages.
okay.
Quoted 5 lines
As an alternative, I suggested representing them as a single node (based on the review comment from Qian Zhang) if you only want to show the shared GPIO enable control instead of the individual voltage rails.
Why do you need an alternative?
Quoted 1 line
Quoted 8 lines
Quoted 2 lines
In AF68E module, 3.85V regulator powers
VDD_PA_5Gand 1.8V regulator powersVDD_PA_2G.Do they power up the WCN6855 itself or some external PA present on the module? In the former case, those regulators should be consumed by the PMU, in the latter case, by the WiFi node. Anyway, they should not be left as always-on / boot-on.
Quoted 7 lines
On this board, the GPIO-controlled regulators power the WCN6855 WiFi module itself (not an external PA). To model this correctly, I updated the device tree like this:
a) I added a single upstream fixed regulator,
wifi_vin, which represents the GPIO enable line (tlmm 91). This is the only node marked always-on, so the enable GPIO stays asserted.
Why? Is there such a regulator on the device? Why is it always-on? What if the user wants to turn WiFi off? If you have consumers, why do you need always-on at all?
Quoted 3 lines
b) The downstream rails
wifi_1p8vandwifi_3p85vare now defined as fixed regulators that depend onwifi_vinusing vin-supply. They no longer control the GPIO directly.
Why? Does the shared GPIO mechanism fail here? If so, how?
Quoted 4 lines
c) These two rails are then explicitly connected as supplies to the WiFi device node (wifi@0) using:
1. vddpaa-supply = <&wifi_3p85v>;
2. vddpab-supply = <&wifi_1p8v>;
Are those documented? Which pin is this regulator connected to?
Quoted 78 lines
With this change, the regulators are not left as generic always-on/ boot-on supplies without a consumer. Instead, the WiFi device node consumes the rails, which matches the real hardware wiring: the GPIO enables power to the WCN6855 rails.
Please find the updated changes below - could you please confirm whether this aligns with your expectations?
arch/arm64/boot/dts/qcom/talos-evk-som.dtsi +25
-10@@ -146,29 +146,41 @@ vreg_pmu_pcie_1p8: ldo9 { }; }; - wifi_1p8v: regulator-wifi-1p8v { + /* Downstream rails controlled by the same GPIO */ + wifi_1p8v: regulator-1p8v { compatible = "regulator-fixed"; + regulator-name = "wifi_1p8v"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>; - enable-active-high; - pinctrl-0 = <&wifi_reg_en_pins_state>; - pinctrl-names = "default"; - regulator-boot-on; - regulator-always-on; + + vin-supply = <&wifi_vin>; }; - wifi_3p85v: regulator-wifi-3p85v { + wifi_3p85v: regulator-3p85v { compatible = "regulator-fixed"; + regulator-name = "wifi_3p85v"; regulator-min-microvolt = <3850000>; regulator-max-microvolt = <3850000>; - gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>; + + vin-supply = <&wifi_vin>; + }; + + /* Upstream supply */ + wifi_vin: regulator-wifi-en { + compatible = "regulator-fixed"; + + regulator-name = "wifi_vin"; + regulator-min-microvolt = <3850000>; + regulator-max-microvolt = <3850000>; + enable-active-high; + gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&wifi_reg_en_pins_state>; pinctrl-names = "default"; - regulator-boot-on; + regulator-always-on; }; };@@ -413,6 +425,9 @@ wifi@0 { vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>; vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>; vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>; + vddpaa-supply = <&wifi_3p85v>; + vddpab-supply = <&wifi_1p8v>; + }; };
Signature · 2 lines
With best wishes Dmitry
Rob Herring
maintainerQuoted 1 line · Sudarshan Shetty
Hi all,
From the mail headers:
Quoted 2 lines
Content-Type: text/plain; charset=y
Content-Transfer-Encoding: 8bit
When git-send-email prompts you for which encoding to use, the correct answer is not 'y'. The default utf-8 is correct, so just hit enter. IIRC, newer git versions fixed this.
Rob
Quoted 11 lines · Rob Herring
Quoted 1 line · Sudarshan Shetty
Hi all,
From the mail headers:
Quoted 2 lines
Content-Type: text/plain; charset=y
Content-Transfer-Encoding: 8bitWhen git-send-email prompts you for which encoding to use, the correct answer is not 'y'. The default utf-8 is correct, so just hit enter. IIRC, newer git versions fixed this.
Okay, got it.
Quoted 1 line
Rob