Skip to contentSkip to conversation

arm64: dts: meson-s4: add support for Khadas VIM1S

PATCH Applied Nick Xie 5 participants 13 messages Jan 15 – Feb 13

Subsystems (3)
lore
Share & tools
lore

Nick Xie

author
#0 lore raw

v3 cover arm64: dts: meson-s4: add support for Khadas VIM1S

This series adds initial support for the Khadas VIM1S single board computer.

The Khadas VIM1S is based on the Amlogic S905Y4 (S4 family) SoC. It features:
- 2GB LPDDR4 RAM
- 16GB eMMC 5.1 storage
- 32MB SPI flash
- 100M Ethernet
- AP6256 Wireless (802.11 a/b/g/n/ac, BT5.0)
- HDMI 2.1 video
- 2x USB 2.0 ports
- 1x USB-C (power) with USB 2.0 OTG
- 2x LED's (1x red, 1x white)
- 3x buttons (power, function, reset)
- IR receiver
- 40pin GPIO Header
- 1x micro SD card slot

Changes in v3:
- Split the patch series to properly distinguish between S805X2 and
S905Y4 SoCs in dt-bindings and compatible strings.
- Patch 1: Updated bindings to use specific compatibles (s805x2/s905y4) instead of just generic s4.
- Patch 2: (New) Updated existing AQ222 dts to use the new s805x2 compatible.
- Patch 3: Updated compatible string to use s905y4.
- Fixed Author/SoB mismatch in all patches.
- Link to v2: https://lore.kernel.org/linux-amlogic/[email protected]/

Changes in v2:
- dts: fixed dtbs_check warning: removed unsupported 'enable-active-low' property from regulator-sd-3v3 node
- Link to v1: https://lore.kernel.org/linux-amlogic/[email protected]/

Nick Xie (3):
dt-bindings: arm: amlogic: introduce specific compatibles for S4
family
arm64: dts: meson-s4-aq222: update compatible string with s805x2
arm64: dts: meson-s4-s905y4-khadas-vim1s: add initial device tree

 .../devicetree/bindings/arm/amlogic.yaml      |   8 +
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../dts/amlogic/meson-s4-s805x2-aq222.dts     |   2 +-
 .../amlogic/meson-s4-s905y4-khadas-vim1s.dts  | 190 ++++++++++++++++++
 4 files changed, 200 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-s4-s905y4-khadas-vim1s.dts
Signature · 1 line
2.34.1
author
#1 lore raw

PATCH v3 1/3 dt-bindings: arm: amlogic: introduce specific compatibles for S4 family

The Amlogic S4 SoC family includes multiple variants, such as the S805X2 and S905Y4. Currently, the bindings only define the generic "amlogic,s4" compatible.

This patch introduces specific compatibles "amlogic,s805x2" and "amlogic,s905y4" to properly differentiate these SoCs while keeping "amlogic,s4" as the family fallback.

This allows for more precise hardware description and future-proofing if SoC-specific quirks arise.

---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 8 ++++++++
 1 file changed, 8 insertions(+)
Documentation/devicetree/bindings/arm/amlogic.yaml +8 -0
index 08d9963fe9259..a885278bc4e2e 100644
@@ -245,6 +245,14 @@ properties:
         items:
           - enum:
               - amlogic,aq222
+          - const: amlogic,s805x2
+          - const: amlogic,s4
+
+      - description: Boards with the Amlogic Meson S4 S905Y4 SoC
+        items:
+          - enum:
+              - khadas,vim1s
+          - const: amlogic,s905y4
           - const: amlogic,s4
 
       - description: Boards with the Amlogic S6 S905X5 SoC
Signature · 1 line
2.34.1
Reviewed-by on v3 1/3
#2 lore raw

Re: [PATCH v3 1/3] dt-bindings: arm: amlogic: introduce specific compatibles for S4 family

Quoted 8 lines · Nick Xie

The Amlogic S4 SoC family includes multiple variants, such as the S805X2 and S905Y4. Currently, the bindings only define the generic "amlogic,s4" compatible.

This patch introduces specific compatibles "amlogic,s805x2" and "amlogic,s905y4" to properly differentiate these SoCs while keeping "amlogic,s4" as the family fallback.

Quoted 7 lines

This allows for more precise hardware description and future-proofing if SoC-specific quirks arise.

---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 8 ++++++++
 1 file changed, 8 insertions(+)

Best regards,
Krzysztof

author
#3 lore raw

PATCH v3 2/3 arm64: dts: meson-s4-aq222: update compatible string with s805x2

In reply to Nick Xie

Update the compatible string for the Amlogic AQ222 board to include the specific SoC compatible "amlogic,s805x2".

This aligns the device tree with the updated bindings which now differentiate between S4 family members (S805X2 vs S905Y4).

---
 arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts +1 -1
index 6730c44642d29..0a3f81ea0fb0a 100644
@@ -9,7 +9,7 @@
 
 / {
 	model = "Amlogic Meson S4 AQ222 Development Board";
-	compatible = "amlogic,aq222", "amlogic,s4";
+	compatible = "amlogic,aq222", "amlogic,s805x2", "amlogic,s4";
 	interrupt-parent = <&gic>;
 	#address-cells = <2>;
 	#size-cells = <2>;
Signature · 1 line
2.34.1
maintainer Reviewed-by on v3 2/3
#4 lore raw

Re: [PATCH v3 2/3] arm64: dts: meson-s4-aq222: update compatible string with s805x2

Quoted 16 lines · Nick Xie

Update the compatible string for the Amlogic AQ222 board to include the specific SoC compatible "amlogic,s805x2".

This aligns the device tree with the updated bindings which now differentiate between S4 family members (S805X2 vs S905Y4).

---
  arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts | 2 +-
  1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts +0 -0
index 6730c44642d29..0a3f81ea0fb0a 100644

arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts line 15

Quoted 8 lines
arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts +1 -1
@@ -9,7 +9,7 @@
 
  / {
  	model = "Amlogic Meson S4 AQ222 Development Board";
-	compatible = "amlogic,aq222", "amlogic,s4";
+	compatible = "amlogic,aq222", "amlogic,s805x2", "amlogic,s4";
  	interrupt-parent = <&gic>;
  	#address-cells = <2>;
  	#size-cells = <2>;

Thanks,
Neil

author
#5 lore raw

PATCH v3 3/3 arm64: dts: meson-s4-s905y4-khadas-vim1s: add initial device tree

In reply to Nick Xie

The Khadas VIM1S uses the Amlogic S905Y4 SoC, based on the Amlogic S4 SoC family, on a board with the same form factor as the VIM/VIM2/VIM3/VIM4 models. Serial debug console, ethernet, SD card work with this initial device tree.

It features:
- 2GB LPDDR4 RAM
- 16GB eMMC 5.1 storage
- 32MB SPI flash
- 100M Ethernet
- AP6256 Wireless (802.11 a/b/g/n/ac, BT5.0)
- HDMI 2.1 video
- 2x USB 2.0 ports
- 1x USB-C (power) with USB 2.0 OTG
- 2x LED's (1x red, 1x white)
- 3x buttons (power, function, reset)
- IR receiver
- 40pin GPIO Header
- 1x micro SD card slot

---
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../amlogic/meson-s4-s905y4-khadas-vim1s.dts  | 190 ++++++++++++++++++
 2 files changed, 191 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-s4-s905y4-khadas-vim1s.dts
arch/arm64/boot/dts/amlogic/Makefile +1 -0
index 219fb088c704d..15f9c817e5023 100644
@@ -85,6 +85,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-ugoos-am3.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-vega-s96.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-s4-s905y4-khadas-vim1s.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m2-pro.dtb
arch/arm64/boot/dts/amlogic/meson-s4-s905y4-khadas-vim1s.dts new file +190 -0

190 lines not on this page · raw message

Signature · 1 line
2.34.1
maintainer Reviewed-by on v3 3/3
#6 lore raw

Re: [PATCH v3 3/3] arm64: dts: meson-s4-s905y4-khadas-vim1s: add initial device tree

Quoted 225 lines · Nick Xie

The Khadas VIM1S uses the Amlogic S905Y4 SoC, based on the Amlogic S4 SoC family, on a board with the same form factor as the VIM/VIM2/VIM3/VIM4 models. Serial debug console, ethernet, SD card work with this initial device tree.

It features:
- 2GB LPDDR4 RAM
- 16GB eMMC 5.1 storage
- 32MB SPI flash
- 100M Ethernet
- AP6256 Wireless (802.11 a/b/g/n/ac, BT5.0)
- HDMI 2.1 video
- 2x USB 2.0 ports
- 1x USB-C (power) with USB 2.0 OTG
- 2x LED's (1x red, 1x white)
- 3x buttons (power, function, reset)
- IR receiver
- 40pin GPIO Header
- 1x micro SD card slot

---
  arch/arm64/boot/dts/amlogic/Makefile          |   1 +
  .../amlogic/meson-s4-s905y4-khadas-vim1s.dts  | 190 ++++++++++++++++++
  2 files changed, 191 insertions(+)

create mode 100644 arch/arm64/boot/dts/amlogic/meson-s4-s905y4-khadas-vim1s.dts

arch/arm64/boot/dts/amlogic/Makefile +1 -0
index 219fb088c704d..15f9c817e5023 100644
@@ -85,6 +85,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-ugoos-am3.dtb
  dtb-$(CONFIG_ARCH_MESON) += meson-gxm-vega-s96.dtb
  dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
  dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-s4-s905y4-khadas-vim1s.dtb
  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m2-pro.dtb
arch/arm64/boot/dts/amlogic/meson-s4-s905y4-khadas-vim1s.dts new file +180 -0
new file mode 100644
index 0000000000000..79ffc703a2e99
@@ -0,0 +1,190 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2026 Khadas Technology Co., Ltd.
+ */
+
+/dts-v1/;
+
+#include "meson-s4.dtsi"
+
+/ {
+	model = "Khadas VIM1S";
+	compatible = "khadas,vim1s", "amlogic,s905y4", "amlogic,s4";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		mmc0 = &emmc; /* eMMC */
+		mmc1 = &sd; /* SD card */
+		mmc2 = &sdio; /* SDIO */
+		serial0 = &uart_b;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 52 MiB reserved for ARM Trusted Firmware */
+		secmon_reserved: secmon@5000000 {
+			reg = <0x0 0x05000000 0x0 0x3400000>;
+			no-map;
+		};
+	};
+
+	sdio_32k: sdio-32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&sdio_32k>;
+		clock-names = "ext_clock";
+	};
+
+	main_5v: regulator-main-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	sd_3v3: regulator-sd-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "SD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio GPIOD_4 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+	};
+
+	vddio_sd: regulator-vddio-sd {
+		compatible = "regulator-gpio";
+		regulator-name = "VDDIO_SD";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio GPIOD_9 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <1800000 1
+				3300000 0>;
+	};
+
+	/* SY8120B1ABC DC/DC Regulator. */
+	vddcpu: regulator-vddcpu {
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU";
+		regulator-min-microvolt = <689000>;
+		regulator-max-microvolt = <1049000>;
+
+		vin-supply = <&main_5v>;
+
+		pwms = <&pwm_ij 1 1500 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+		/* Voltage Duty-Cycle */
+		voltage-table = <1049000 0>,
+				<1039000 3>,
+				<1029000 6>,
+				<1019000 9>,
+				<1009000 12>,
+				<999000 14>,
+				<989000 17>,
+				<979000 20>,
+				<969000 23>,
+				<959000 26>,
+				<949000 29>,
+				<939000 31>,
+				<929000 34>,
+				<919000 37>,
+				<909000 40>,
+				<899000 43>,
+				<889000 45>,
+				<879000 48>,
+				<869000 51>,
+				<859000 54>,
+				<849000 56>,
+				<839000 59>,
+				<829000 62>,
+				<819000 65>,
+				<809000 68>,
+				<799000 70>,
+				<789000 73>,
+				<779000 76>,
+				<769000 79>,
+				<759000 81>,
+				<749000 84>,
+				<739000 87>,
+				<729000 89>,
+				<719000 92>,
+				<709000 95>,
+				<699000 98>,
+				<689000 100>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	phy-handle = <&internal_ephy>;
+	phy-mode = "rmii";
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins1>;
+	pinctrl-names = "default";
+};
+
+&pwm_ij {
+	status = "okay";
+};
+
+&sd {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+
+	vmmc-supply = <&sd_3v3>;
+	vqmmc-supply = <&vddio_sd>;
+};
+

arch/arm64/boot/dts/amlogic/meson-s4-s905y4-khadas-vim1s.dts line 190

Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-s4-s905y4-khadas-vim1s.dts new file +10 -0
+&spicc0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spicc0_pins_x>;
+	cs-gpios = <&gpio GPIOX_10 GPIO_ACTIVE_LOW>;
+};
+
+&uart_b {
+	status = "okay";
+};

Thanks,
Neil

#7 lore raw

Re: [DMARC error] [PATCH v3 3/3] arm64: dts: meson-s4-s905y4-khadas-vim1s: add initial device tree

In reply to Nick Xie

Hello Nick

Quoted 4 lines · Nick Xie

The Khadas VIM1S uses the Amlogic S905Y4 SoC, based on the Amlogic S4 SoC family, on a board with the same form factor as the VIM/VIM2/VIM3/VIM4 models. Serial debug console, ethernet, SD card work with this initial device tree.

...

Quoted 47 lines
arch/arm64/boot/dts/amlogic/meson-s4-s905y4-khadas-vim1s.dts new file +47 -0
+	};
+
+	/* SY8120B1ABC DC/DC Regulator. */
+	vddcpu: regulator-vddcpu {
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU";
+		regulator-min-microvolt = <689000>;
+		regulator-max-microvolt = <1049000>;
+
+		vin-supply = <&main_5v>;
+
+		pwms = <&pwm_ij 1 1500 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+		/* Voltage Duty-Cycle */
+		voltage-table = <1049000 0>,
+				<1039000 3>,
+				<1029000 6>,
+				<1019000 9>,
+				<1009000 12>,
+				<999000 14>,
+				<989000 17>,
+				<979000 20>,
+				<969000 23>,
+				<959000 26>,
+				<949000 29>,
+				<939000 31>,
+				<929000 34>,
+				<919000 37>,
+				<909000 40>,
+				<899000 43>,
+				<889000 45>,
+				<879000 48>,
+				<869000 51>,
+				<859000 54>,
+				<849000 56>,
+				<839000 59>,
+				<829000 62>,
+				<819000 65>,
+				<809000 68>,
+				<799000 70>,
+				<789000 73>,
+				<779000 76>,
+				<769000 79>,

arch/arm64/boot/dts/amlogic/meson-s4-s905y4-khadas-vim1s.dts line 137

Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-s4-s905y4-khadas-vim1s.dts new file +10 -0
+				<759000 81>,
+				<749000 84>,
+				<739000 87>,
+				<729000 89>,
+				<719000 92>,
+				<709000 95>,
+				<699000 98>,
+				<689000 100>;
+	};
+};

Thanks for the patch. Since you have khadas mail I'm pretty sure you've had the possibility to test it on the real vim board and I just don't get it how it works with the voltage table above. The problem is that pwm is calculated incorrectly in the upstream pwm-meson driver. That voltage table appeared to be used in early amlogic bl loader and appropriate pwm is initialized from a table's record. Duty cycle value is translated to pwm regs correctly. Later when kernel start running pwm-regulator driver is probed. It reads the pwm regs, calculates back duty-cyle and search it in the table. Since calculation algos are not match and the table doesn't contain full range of 0-100% values regulator driver doesn't find current voltage. In such case regulator core sets the minimum voltage from the table [1] and the SoC may hang (depending on board) due to minimum voltage may be too low for the current frequency SoC uses.

Or I'm missing something?

There's not-yet-reviewed patch that fixes pwm algo [2]. There's calculation example in the cover letter.

[1] https://elixir.bootlin.com/linux/v6.19-rc5/source/drivers/regulator/core.c#L1227
[2] https://lkml.iu.edu/2412.3/00826.html

Signature · 2 lines
Best regards
George
author
#8 lore raw

回复: [DMARC error] [PATCH v3 3/3] arm64: dts: meson-s4-s905y4-khadas-vim1s: add initial device tree

Quoted 6 lines

Thanks for the patch. Since you have khadas mail I'm pretty sure you've had the possibility to test it on the real vim board and I just don't get it how it works with the voltage table above. The problem is that pwm is calculated incorrectly in the upstream pwm-meson driver. That voltage table appeared to be used in early amlogic bl loader and appropriate pwm is initialized from a table's record. Duty cycle value

Quoted 8 lines

is translated to pwm regs correctly. Later when kernel start running pwm-regulator driver is probed. It reads the pwm regs, calculates back duty-cyle and search it in the table. Since calculation algos are not match and the table doesn't contain full range of 0-100% values regulator driver doesn't find current voltage. In such case regulator core sets the minimum voltage from the table [1] and the SoC may hang (depending on board) due to minimum voltage may be too low for the current frequency SoC uses.

I'm not sure about the PWM issues, but I checked on the real S905Y4 hardware and it works.

Quoted 7 lines

Or I'm missing something?

There's not-yet-reviewed patch that fixes pwm algo [2]. There's calculation example in the cover letter.
[1] https://elixir.bootlin.com/linux/v6.19-rc5/source/drivers/regulator/core.c#L1227
[2] https://lkml.iu.edu/2412.3/00826.html

What's the status of such patches?

--

Best regards

George

#9 lore raw

Re: 回复: [DMARC error] [PATCH v3 3/3] arm64: dts: meson-s4-s905y4-khadas-vim1s: add initial device tree

Quoted 15 lines · Nick Xie
Quoted 6 lines

Thanks for the patch. Since you have khadas mail I'm pretty sure you've had the possibility to test it on the real vim board and I just don't get it how it works with the voltage table above. The problem is that pwm is calculated incorrectly in the upstream pwm-meson driver. That voltage table appeared to be used in early amlogic bl loader and appropriate pwm is initialized from a table's record. Duty cycle value

Quoted 8 lines

is translated to pwm regs correctly. Later when kernel start running pwm-regulator driver is probed. It reads the pwm regs, calculates back duty-cyle and search it in the table. Since calculation algos are not match and the table doesn't contain full range of 0-100% values regulator driver doesn't find current voltage. In such case regulator core sets the minimum voltage from the table [1] and the SoC may hang (depending on board) due to minimum voltage may be too low for the current frequency SoC uses.

Quoted 2 lines

I'm not sure about the PWM issues, but I checked on the real S905Y4 hardware and it works.

To prove my point: run the kernel with the next patch:

drivers/regulator/pwm-regulator.c +3 -0
index 7434b6b22d32..14d2730b21e8 100644
@@ -86,6 +86,9 @@ static int pwm_regulator_set_voltage_sel(struct regulator_dev *rdev,
        struct pwm_state pstate;
        int ret;
 
+       dev_info(&rdev->dev, "setting voltage from table: index: %u, uV: %u\n",
+               selector, drvdata->duty_cycle_table[selector].uV);
+
        pwm_init_state(drvdata->pwm, &pstate);
        pwm_set_relative_duty_cycle(&pstate,
                        drvdata->duty_cycle_table[selector].dutycycle, 

100);

In dmesg there must be a message like "setting voltage from table: index: 36, uV: 689000" If to take a look at operation points table for s4 in vendor kernels the lowest voltage is 0.769V for 100Mhz so setting 689000uV even temporary may lead to problems depending on particular hardware.

Quoted 9 lines
Quoted 7 lines

Or I'm missing something?

There's not-yet-reviewed patch that fixes pwm algo [2]. There's calculation example in the cover letter.
[1] https://elixir.bootlin.com/linux/v6.19-rc5/source/drivers/regulator/core.c#L1227
[2] https://lkml.iu.edu/2412.3/00826.html

What's the status of such patches?

the patch is ready for review. It's seems like nobody is interested

Quoted 6 lines

--

Best regards

George

Signature · 2 lines
Best regards
George
#10 lore raw

Re: 回复: [DMARC error] [PATCH v3 3/3] arm64: dts: meson-s4-s905y4-khadas-vim1s: add initial device tree

Hi George,

sorry for the late reply.

Quoted 4 lines · George Stark

On 1/26/26 12:35, Nick Xie wrote:

Quoted 14 lines
Quoted 6 lines
Quoted 6 lines

Thanks for the patch. Since you have khadas mail I'm pretty sure you've had the possibility to test it on the real vim board and I just don't get it how it works with the voltage table above. The problem is that pwm is calculated incorrectly in the upstream pwm-meson driver. That voltage table appeared to be used in early amlogic bl loader and appropriate pwm is initialized from a table's record. Duty cycle value

Quoted 8 lines
Quoted 8 lines

is translated to pwm regs correctly. Later when kernel start running pwm-regulator driver is probed. It reads the pwm regs, calculates back duty-cyle and search it in the table. Since calculation algos are not match and the table doesn't contain full range of 0-100% values regulator driver doesn't find current voltage. In such case regulator core sets the minimum voltage from the table [1] and the SoC may hang (depending on board) due to minimum voltage may be too low for the current frequency SoC uses.

Nick likely didn't spot any issues on S4 since CPU frequency scaling is not upstreamed yet (as there's no way to control the CPU clock yet).
The lack of a OPP table means: the PWM and CPU clock will just stay at whatever the bootloader provides

Quoted 11 lines
Quoted 9 lines
Quoted 7 lines

Or I'm missing something?

There's not-yet-reviewed patch that fixes pwm algo [2]. There's calculation example in the cover letter.
[1] https://elixir.bootlin.com/linux/v6.19-rc5/source/drivers/regulator/core.c#L1227
[2] https://lkml.iu.edu/2412.3/00826.html

What's the status of such patches?

the patch is ready for review. It's seems like nobody is interested

I'm sorry to see that the patch had it's first anniversary. I'll need to bring out my logic analyzer and test your patch (I hope it's precise enough to show the impact of your changes). Are your plans then to re-send the patches or have you moved on and need someone else to take care of it?

Best regards,
Martin

#11 lore raw

Re: 回复: [DMARC error] [PATCH v3 3/3] arm64: dts: meson-s4-s905y4-khadas-vim1s: add initial device tree

Quoted 5 lines · Martin Blumenstingl

Hi George,

sorry for the late reply.

On Thu, Jan 29, 2026 at 3:48 PM George Stark <[email protected]> wrote:

Hello Martin. It's great to hear from you again.

Quoted 17 lines
Quoted 9 lines · Nick Xie
Quoted 6 lines
Quoted 6 lines

Thanks for the patch. Since you have khadas mail I'm pretty sure you've had the possibility to test it on the real vim board and I just don't get it how it works with the voltage table above. The problem is that pwm is calculated incorrectly in the upstream pwm-meson driver. That voltage table appeared to be used in early amlogic bl loader and appropriate pwm is initialized from a table's record. Duty cycle value

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines

is translated to pwm regs correctly. Later when kernel start running pwm-regulator driver is probed. It reads the pwm regs, calculates back duty-cyle and search it in the table. Since calculation algos are not match and the table doesn't contain full range of 0-100% values regulator driver doesn't find current voltage. In such case regulator core sets the minimum voltage from the table [1] and the SoC may hang (depending on board) due to minimum voltage may be too low for the current frequency SoC uses.

Quoted 5 lines

Nick likely didn't spot any issues on S4 since CPU frequency scaling is not upstreamed yet (as there's no way to control the CPU clock yet).
The lack of a OPP table means: the PWM and CPU clock will just stay at whatever the bootloader provides

It makes sense. I should experiment on the latest kernel.

Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 7 lines

Or I'm missing something?

There's not-yet-reviewed patch that fixes pwm algo [2]. There's calculation example in the cover letter.
[1] https://elixir.bootlin.com/linux/v6.19-rc5/source/drivers/regulator/core.c#L1227
[2] https://lkml.iu.edu/2412.3/00826.html

Quoted 8 lines
Quoted 3 lines
Quoted 1 line

What's the status of such patches?

the patch is ready for review. It's seems like nobody is interested

I'm sorry to see that the patch had it's first anniversary. I'll need to bring out my logic analyzer and test your patch (I hope it's precise enough to show the impact of your changes). Are your plans then to re-send the patches or have you moved on and need someone else to take care of it?

It's a major step anyway if you confirm the issue yourself with an analyzer. In that case discussion won't be delayed for one more year I think. Thanks.

Sure I'm ready to discuss/fix/resend this patch.

Signature · 2 lines
Best regards
George
maintainer Applied
#12 lore raw
In reply to Nick Xie

Hi,

Quoted 18 lines · Nick Xie

This series adds initial support for the Khadas VIM1S single board computer.

The Khadas VIM1S is based on the Amlogic S905Y4 (S4 family) SoC. It features:
- 2GB LPDDR4 RAM
- 16GB eMMC 5.1 storage
- 32MB SPI flash
- 100M Ethernet
- AP6256 Wireless (802.11 a/b/g/n/ac, BT5.0)
- HDMI 2.1 video
- 2x USB 2.0 ports
- 1x USB-C (power) with USB 2.0 OTG
- 2x LED's (1x red, 1x white)
- 3x buttons (power, function, reset)
- IR receiver
- 40pin GPIO Header
- 1x micro SD card slot

Quoted 1 line

[...]

Thanks, Applied to https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git (v6.20/arm64-dt)

[1/3] dt-bindings: arm: amlogic: introduce specific compatibles for S4 family

      https://git.kernel.org/amlogic/c/fee65328ab35d5491ac5c9c697c52da3fd068268
[2/3] arm64: dts: meson-s4-aq222: update compatible string with s805x2
      https://git.kernel.org/amlogic/c/9ba73c18b14ac297b9fae92b684ca4dafa5e0361
[3/3] arm64: dts: meson-s4-s905y4-khadas-vim1s: add initial device tree
      https://git.kernel.org/amlogic/c/6186af6bd9b1e778e295a176c9281dba970da7eb

These changes has been applied on the intermediate git tree [1].

The v6.20/arm64-dt branch will then be sent via a formal Pull Request to the Linux SoC maintainers for inclusion in their intermediate git branches in order to be sent to Linus during the next merge window, or sooner if it's a set of fixes.

In the cases of fixes, those will be merged in the current release candidate kernel and as soon they appear on the Linux master branch they will be backported to the previous Stable and Long-Stable kernels [2].

The intermediate git branches are merged daily in the linux-next tree [3], people are encouraged testing these pre-release kernels and report issues on the relevant mailing-lists.

If problems are discovered on those changes, please submit a signed-off-by revert patch followed by a corrective changeset.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
[3] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git

Signature · 1 line
Neil