ARM: dts: renesas: r9a06g032: Add support for CPU frequency scaling
Subsystems (2)
PATCH v2 1/1 ARM: dts: renesas: r9a06g032: Add support for CPU frequency scaling
In RZ/N1 SoCs, CPUs are allowed to work at 125, 250 or 500 MHz when the 'ref' clock frequency value is set to 500 MHz which is the default 'ref' clock frequency value.
Add support for CPU frequency scaling defining those 3 frequencies in the opp-table with the assumption that the 'ref' clock is set to its default value.
---
Changes v1 -> v2
v1: https://lore.kernel.org/all/[email protected]/
Fix Author and SoB.
arch/arm/boot/dts/renesas/r9a06g032.dtsi | 35 ++++++++++++++++++++++++ 1 file changed, 35 insertions(+)
arch/arm/boot/dts/renesas/r9a06g032.dtsi +35 -0
@@ -15,6 +15,39 @@ / { #size-cells = <1>; interrupt-parent = <&gic>; + /* + * The CPUs clock is based on the 'ref' clock (output of OPPDIV divisor) + * with x1, x2 or x4 ratio between the CPUs clock frequency and this + * 'ref' clock frequency. + * + * The table below is built on the assumption that the 'ref' clock + * frequency is set to 500MHz which is its default value. + * + * The table should be overridden in the board device-tree file based + * on the 'ref' clock frequency if this frequency value is not the + * default one. + */ + cpu_opp_table: opp-table-cpu { + compatible = "operating-points-v2"; + opp-shared; + + opp-125000000 { + opp-hz = /bits/ 64 <125000000>; + /* ~35 clocks cycles at 125mhz */ + clock-latency-ns = <300>; + }; + + opp-250000000 { + opp-hz = /bits/ 64 <250000000>; + clock-latency-ns = <300>; + }; + + opp-500000000 { + opp-hz = /bits/ 64 <500000000>; + clock-latency-ns = <300>; + }; + }; + cpus { #address-cells = <1>; #size-cells = <0>;
@@ -24,6 +57,7 @@ cpu@0 { compatible = "arm,cortex-a7"; reg = <0>; clocks = <&sysctrl R9A06G032_CLK_A7MP>; + operating-points-v2 = <&cpu_opp_table>; }; cpu@1 {
@@ -33,6 +67,7 @@ cpu@1 { clocks = <&sysctrl R9A06G032_CLK_A7MP>; enable-method = "renesas,r9a06g032-smp"; cpu-release-addr = <0 0x4000c204>; + operating-points-v2 = <&cpu_opp_table>; }; };
Signature · 1 line
2.52.0
Hi Hervé,
Quoted 9 lines · Herve Codina (Schneider Electric)
In RZ/N1 SoCs, CPUs are allowed to work at 125, 250 or 500 MHz when the 'ref' clock frequency value is set to 500 MHz which is the default 'ref' clock frequency value.
Add support for CPU frequency scaling defining those 3 frequencies in the opp-table with the assumption that the 'ref' clock is set to its default value.
Signed-off-by Herve Codina (Schneider Electric) <[email protected]>
Thanks for your patch, which LGTM.
arch/arm/boot/dts/renesas/r9a06g032.dtsi cpu@0 { · line 63
Quoted 11 lines
arch/arm/boot/dts/renesas/r9a06g032.dtsi +1
-0@@ -24,6 +57,7 @@ cpu@0 { compatible = "arm,cortex-a7"; reg = <0>; clocks = <&sysctrl R9A06G032_CLK_A7MP>; + operating-points-v2 = <&cpu_opp_table>; }; cpu@1 {
Unless I am missing something, the RZ/N1 clock driver does not support the A7MP clock yet, so how can cpufreq work for you?
Gr{oetje,eeting}s,
Geert
Signature · 5 lines
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected] In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds
Quoted 26 lines · On Mon, 2 Mar 2026 18:04:36 +0100 Geert Uytterhoeven <[email protected]>…
Hi Hervé,
Quoted 9 lines · Herve Codina (Schneider Electric)
In RZ/N1 SoCs, CPUs are allowed to work at 125, 250 or 500 MHz when the 'ref' clock frequency value is set to 500 MHz which is the default 'ref' clock frequency value.
Add support for CPU frequency scaling defining those 3 frequencies in the opp-table with the assumption that the 'ref' clock is set to its default value.
Signed-off-by Herve Codina (Schneider Electric) <[email protected]>Thanks for your patch, which LGTM.
Quoted 10 lines
arch/arm/boot/dts/renesas/r9a06g032.dtsi +1
-0@@ -24,6 +57,7 @@ cpu@0 { compatible = "arm,cortex-a7"; reg = <0>; clocks = <&sysctrl R9A06G032_CLK_A7MP>; + operating-points-v2 = <&cpu_opp_table>; };
Quoted 4 lines
arch/arm/boot/dts/renesas/r9a06g032.dtsi cpu@0 { · line 63
Quoted 1 line
arch/arm/boot/dts/renesas/r9a06g032.dtsi +0
-0cpu@1 {Unless I am missing something, the RZ/N1 clock driver does not support the A7MP clock yet, so how can cpufreq work for you?
R9A06G032_CLK_A7MP is DIV_CA7
https://elixir.bootlin.com/linux/v6.19.3/source/include/dt-bindings/clock/r9a06g032-sysctrl.h#L78
https://elixir.bootlin.com/linux/v6.19.3/source/drivers/clk/renesas/r9a06g032-clocks.c#L261
https://elixir.bootlin.com/linux/v6.19.3/source/drivers/clk/renesas/r9a06g032-clocks.c#L455
And on my system, got the following:
# cat /sys/devices/system/cpu/cpufreq/policy0/stats/time_in_state 125000 4574 250000 108 500000 392 #
All defined opp-hz values seems to be used without any errors. I hope that any errors would be reported in kernel logs. At least this one:
https://elixir.bootlin.com/linux/v6.19.3/source/drivers/cpufreq/cpufreq.c#L2329
Best regards,
Hervé
Geert Uytterhoeven
Reviewed-byHi Hervé,
Quoted 29 lines · Herve Codina
Quoted 26 lines · On Mon, 2 Mar 2026 18:04:36 +0100 Geert Uytterhoeven <[email protected]>…
Hi Hervé,
Quoted 9 lines · Herve Codina (Schneider Electric)
In RZ/N1 SoCs, CPUs are allowed to work at 125, 250 or 500 MHz when the 'ref' clock frequency value is set to 500 MHz which is the default 'ref' clock frequency value.
Add support for CPU frequency scaling defining those 3 frequencies in the opp-table with the assumption that the 'ref' clock is set to its default value.
Signed-off-by Herve Codina (Schneider Electric) <[email protected]>Thanks for your patch, which LGTM.
Quoted 10 lines
arch/arm/boot/dts/renesas/r9a06g032.dtsi +1
-0@@ -24,6 +57,7 @@ cpu@0 { compatible = "arm,cortex-a7"; reg = <0>; clocks = <&sysctrl R9A06G032_CLK_A7MP>; + operating-points-v2 = <&cpu_opp_table>; };
Quoted 6 lines
Quoted 4 lines
arch/arm/boot/dts/renesas/r9a06g032.dtsi cpu@0 { · line 63
Quoted 1 line
arch/arm/boot/dts/renesas/r9a06g032.dtsi +0
-0cpu@1 {Unless I am missing something, the RZ/N1 clock driver does not support the A7MP clock yet, so how can cpufreq work for you?
R9A06G032_CLK_A7MPisDIV_CA7
Thank you!
i.e. will queue in renesas-devel for v7.1.
Gr{oetje,eeting}s,
Geert
Signature · 5 lines
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected] In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds