net: phy: realtek: add RTL8224 pair swap support
Subsystems (4)
PATCH 1/2 net: phy: realtek: add RTL8224 pair swap support
The RTL8224 has a register to configure a pair swap (from ABCD order to DCBA) providing PCB designers more flexbility when wiring the chip. The swap parameter has to be set correctly for each of the 4 ports before the chip can detect a link.
After a reset, this register is (unfortunately) left in a random state, thus it has to be initialized. On most of the devices the bootloader does it once for all and we can rely on the value set, on some other it is not and the kernel has to do it.
The MDI pair swap can be set in the device tree using the property realtek,mdi-pair-swap. The property is set to "off" to disable the pair swap, "on" to enable it, or "keep"/unset to keep the current configuration.
--- .../bindings/net/realtek,rtl82xx.yaml | 13 ++++ drivers/net/phy/realtek/Kconfig | 1 + drivers/net/phy/realtek/realtek_main.c | 74 +++++++++++++++++++ 3 files changed, 88 insertions(+)
Documentation/devicetree/bindings/net/realtek,rtl82xx.yaml +13 -0
@@ -55,6 +55,18 @@ properties: description: Enable Wake-on-LAN support for the RTL8211F PHY. + realtek,mdi-pair-swap: + description: + Enable or disable the swap of the ethernet pairs (from ABCD to DCBA). + The "keep" setting will keep the pair configuration at whatever its + current state is. + $ref: /schemas/types.yaml#/definitions/string + enum: + - keep + - on + - off + default: keep + unevaluatedProperties: false allOf:
@@ -79,5 +91,6 @@ examples: reg = <1>; realtek,clkout-disable; realtek,aldps-enable; + realtek,mdi-pair-swap = "on"; }; };
drivers/net/phy/realtek/Kconfig +1 -0
@@ -1,6 +1,7 @@ # SPDX-License-Identifier: GPL-2.0-only config REALTEK_PHY tristate "Realtek PHYs" + select PHY_PACKAGE help Currently supports RTL821x/RTL822x and fast ethernet PHYs
drivers/net/phy/realtek/realtek_main.c +74 -0
104 lines not on this page · raw message
base-commit: 983d014aafb14ee5e4915465bf8948e8f3a723b5
Signature · 1 line
2.47.3
PATCH 2/2 net: phy: realtek: add RTL8224 polarity swap support
The RTL8224 has a register to configure the polarity of every pair of each port. It provides device designers more flexbility when wiring the chip.
Unfortunately, the register is left in an unknown state after a reset. Thus on devices where the bootloader don't initialize it, the driver has to do it to detect and use a link.
The MDI polarity swap can be set in the device tree using the property realtek,mdi-polarity-swap. The u32 value is a bitfield where bit[0..3] control the polarity of pairs A...D.
--- .../bindings/net/realtek,rtl82xx.yaml | 7 +++++ drivers/net/phy/realtek/realtek_main.c | 29 +++++++++++++++++++ 2 files changed, 36 insertions(+)
Documentation/devicetree/bindings/net/realtek,rtl82xx.yaml +7 -0
@@ -67,6 +67,13 @@ properties: - off default: keep + realtek,mdi-polarity-swap: + description: + A bitmap to describe pair polarity swap. Bit 0 to swap polarity of pair A, + bit 1 to swap polarity of pair B, bit 2 to swap polarity of pair C and bit + 3 to swap polarity of pair D. + $ref: /schemas/types.yaml#/definitions/uint32 + unevaluatedProperties: false allOf:
drivers/net/phy/realtek/realtek_main.c +29 -0
@@ -164,6 +164,7 @@#define RTL8224_SRAM_RTCT_LEN (pair) (0x8028 + (pair) * 4)#define RTL8224_VND1_MDI_PAIR_SWAP 0xa90 +#define RTL8224_VND1_MDI_POLARITY_SWAP 0xa94#define RTL8366RB_POWER_SAVE 0x15#define RTL8366RB_POWER_SAVE_ON BIT(12)
@@ -219,6 +220,7 @@ enum pair_swap_state {struct rtl8224_priv {enum pair_swap_state pair_swap; +int polarity_swap; };static int rtl821x_read_page (struct phy_device *phydev)
@@ -1713,12 +1715,28 @@ static void rtl8224_mdi_pair_swap(struct phy_device *phydev, bool swap) RTL8224_VND1_MDI_PAIR_SWAP, val); } +static void rtl8224_mdi_polarity_swap (struct phy_device *phydev,u32 swap) +{ +u32 val; +u8 offset; + + offset = (phydev->mdio.addr &3 ) *4 ; + val =__phy_package_read_mmd (phydev,0 ,MDIO_MMD_VEND1 , +RTL8224_VND1_MDI_POLARITY_SWAP ); + val &= ~(0xf << offset); + val |= (swap &0xf ) << offset; +__phy_package_write_mmd (phydev,0 ,MDIO_MMD_VEND1 , +RTL8224_VND1_MDI_POLARITY_SWAP , val); +} +static int rtl8224_config_init (struct phy_device *phydev) {struct rtl8224_priv *priv = phydev->priv;if (priv->pair_swap !=PAIR_SWAP_KEEP )rtl8224_mdi_pair_swap (phydev, priv->pair_swap ==PAIR_SWAP_ON ); +if (priv->polarity_swap >=0 ) +rtl8224_mdi_polarity_swap (phydev, priv->polarity_swap);return 0 ; }
@@ -1737,6 +1755,16 @@ static enum pair_swap_state rtlgen_pair_swap_state_get(const struct device_nodereturn PAIR_SWAP_KEEP ; } +static int rtlgen_polarity_swap_get (const struct device_node *np) +{ +u32 polarity; + +if (!of_property_read_u32 (np,"realtek,mdi-polarity-swap" , &polarity)) +return polarity; + +return -1 ; +} +static int rtl8224_probe (struct phy_device *phydev) {struct device *dev = &phydev->mdio.dev;
@@ -1748,6 +1776,7 @@ static int rtl8224_probe(struct phy_device *phydev) phydev->priv = priv; priv->pair_swap =rtlgen_pair_swap_state_get (dev->of_node); + priv->polarity_swap =rtlgen_polarity_swap_get (dev->of_node);/* Device has 4 ports */ devm_phy_package_join (dev, phydev, phydev->mdio.addr & (~3 ),0 );
Signature · 1 line
2.47.3
Re: [PATCH 2/2] net: phy: realtek: add RTL8224 polarity swap support
Quoted 23 lines · Damien Dejean
The RTL8224 has a register to configure the polarity of every pair of each port. It provides device designers more flexbility when wiring the chip.
Unfortunately, the register is left in an unknown state after a reset. Thus on devices where the bootloader don't initialize it, the driver has to do it to detect and use a link.
The MDI polarity swap can be set in the device tree using the property realtek,mdi-polarity-swap. The u32 value is a bitfield where bit[0..3] control the polarity of pairs A...D.
Signed-off-by Damien Dejean <[email protected]>--- .../bindings/net/realtek,rtl82xx.yaml | 7 +++++ drivers/net/phy/realtek/realtek_main.c | 29 +++++++++++++++++++ 2 files changed, 36 insertions(+)Documentation/devicetree/bindings/net/realtek,rtl82xx.yaml +0
-0
Documentation/devicetree/bindings/net/realtek,rtl82xx.yaml properties: · line 75
Quoted 9 lines
Documentation/devicetree/bindings/net/realtek,rtl82xx.yaml +6
-0@@ -67,6 +67,13 @@ properties: - off default: keep + realtek,mdi-polarity-swap: + description: + A bitmap to describe pair polarity swap. Bit 0 to swap polarity of pair A, + bit 1 to swap polarity of pair B, bit 2 to swap polarity of pair C and bit + 3 to swap polarity of pair D. + $ref: /schemas/types.yaml#/definitions/uint32
Same problem.
Best regards,
Krzysztof
Andrew Lunn
maintainerQuoted 4 lines · Damien Dejean
The RTL8224 has a register to configure a pair swap (from ABCD order to DCBA) providing PCB designers more flexbility when wiring the chip. The swap parameter has to be set correctly for each of the 4 ports before the chip can detect a link.
Does the PHY support auto MDI-X, where it figures out a working combination at link up time? That allows you to use crossed or not crossed cables.
Anyway, the DT property you are adding seems to be the same as marvell,mdi-cfg-order. See commit:
1432965bf5ce ("dt-bindings: net: marvell,aquantia: add property to override MDI_CFG")
Quoted 1 line
+ realtek,mdi-pair-swap:
Maybe call this realtek,mdi-cfg-order and use the same binding?
Documentation/devicetree/bindings/net/realtek,rtl82xx.yaml properties: · line 65
Quoted 7 lines
Documentation/devicetree/bindings/net/realtek,rtl82xx.yaml +7
-0+ description: + Enable or disable the swap of the ethernet pairs (from ABCD to DCBA). + The "keep" setting will keep the pair configuration at whatever its + current state is. + $ref: /schemas/types.yaml#/definitions/string + enum: + - keep
You should not need keep. If the property is not present in DT, you by default do nothing, which would be keep.
drivers/net/phy/realtek/Kconfig line 6
Quoted 11 lines
drivers/net/phy/realtek/Kconfig +1
-0@@ -1,6 +1,7 @@ # SPDX-License-Identifier: GPL-2.0-only config REALTEK_PHY tristate "Realtek PHYs" + select PHY_PACKAGE help Currently supports RTL821x/RTL822x and fast ethernet PHYs
Changes to DT bindings should be in a patch of its own.
Andrew
---
pw-bot: cr
Hi Andrew, Krzysztof,
Thanks for your feedbacks.
Quoted 4 lines · Andrew Lunn
Does the PHY support auto MDI-X, where it figures out a working combination at link up time? That allows you to use crossed or not crossed cables.
It does support auto MDI-X, it’s possible to read the status of it after a cable is connected. However this is different from the swap mechanism I’m introducing here.
Quoted 9 lines
Anyway, the DT property you are adding seems to be the same as marvell,mdi-cfg-order. See commit:
1432965bf5ce("dt-bindings: net: marvell,aquantia: add property to overrideMDI_CFG")Quoted 1 line
+ realtek,mdi-pair-swap:
Maybe call this realtek,mdi-cfg-order and use the same binding?
It looks like the same mechanism, thanks for the reference. The aquantia implementation looks more straightforward, let me rework the patchs to have a similar implementation.
Quoted 1 line
Changes to DT bindings should be in a patch of its own.
Thanks for the notice, I missed that when I ran checkpatch.
Damien
Quoted 10 lines · Damien Dejean
The RTL8224 has a register to configure a pair swap (from ABCD order to DCBA) providing PCB designers more flexbility when wiring the chip. The swap parameter has to be set correctly for each of the 4 ports before the chip can detect a link.
After a reset, this register is (unfortunately) left in a random state, thus it has to be initialized. On most of the devices the bootloader does it once for all and we can rely on the value set, on some other it is not and the kernel has to do it.
Quoted 8 lines
The MDI pair swap can be set in the device tree using the property realtek,mdi-pair-swap. The property is set to "off" to disable the pair swap, "on" to enable it, or "keep"/unset to keep the current configuration.
Signed-off-by Damien Dejean <[email protected]>--- .../bindings/net/realtek,rtl82xx.yaml | 13 ++++
Please run scripts/checkpatch.pl on the patches and fix reported warnings. After that, run also 'scripts/checkpatch.pl --strict' on the patches and (probably) fix more warnings. Some warnings can be ignored, especially from --strict run, but the code here looks like it needs a fix. Feel free to get in touch if the warning is not clear.
Please use scripts/get_maintainers.pl to get a list of necessary people and lists to CC (and consider --no-git-fallback argument, so you will not CC people just because they made one commit years ago). It might happen, that command when run on an older kernel, gives you outdated entries. Therefore please be sure you base your patches on recent Linux kernel.
Tools like b4 or scripts/get_maintainer.pl provide you proper list of people, so fix your workflow. Tools might also fail if you work on some ancient tree (don't, instead use mainline) or work on fork of kernel (don't, instead use mainline). Just use b4 and everything should be fine, although remember about b4 prep --auto-to-cc if you added new patches to the patchset.
Best regards,
Krzysztof