Skip to contentSkip to conversation

board: kontron: add initial SMARC-sAM67 support

PATCH In review Michael Walle 1 participant 6 messages Jan 27 – Jan 28

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

cover board: kontron: add initial SMARC-sAM67 support

Add initial support for the SMARC-sAM67 board (enineering name sa67).

The board has different RAM options. The exact configuration is tri-state encoded with strapping options. u-boot already has support for that, but unfortunately, the pull-ups/-downs can only be configured by the pinmux and not by the gpio controller. Therefore, this will introduce another method to read the tri-state encoded strappings by switching the pinmux configurations on the fly.

There is also a sysinfo driver to read the remaining board options and is used to apply corresponding device tree overlays.

The device tree itself is picked from the last tag of the dt-rebasing tree.

Michael Walle (4):
arm64: dts: ti: Add support for Kontron SMARC-sAM67
sysinfo: add driver for the Kontron SMARC-sAM67 board
gpio: 3way strapping: add pinctrl method
board: kontron: initial commit for the SMARC-sAM67

 .../k3-am67a-kontron-sa67-base-u-boot.dtsi    |  127 +
 .../arm/dts/k3-am67a-kontron-sa67-binman.dtsi |  202 ++
 ...m67a-kontron-sa67-ddr-mt53e256m32d1ks.dtsi | 2797 +++++++++++++++++
 ...-am67a-kontron-sa67-ddr-mt53e2g32d4de.dtsi | 2797 +++++++++++++++++
 ...-am67a-r5-kontron-sa67-mt53e256m32d1ks.dts |   16 +
 ...k3-am67a-r5-kontron-sa67-mt53e2g32d4de.dts |   17 +
 arch/arm/dts/k3-am67a-r5-kontron-sa67.dtsi    |  104 +
 arch/arm/mach-k3/j722s/Kconfig                |   18 +
 board/kontron/sa67/Kconfig                    |   21 +
 board/kontron/sa67/MAINTAINERS                |    7 +
 board/kontron/sa67/Makefile                   |    5 +
 board/kontron/sa67/board-cfg.yaml             |   36 +
 board/kontron/sa67/common.c                   |   41 +
 board/kontron/sa67/pm-cfg.yaml                |   12 +
 board/kontron/sa67/r5.c                       |  144 +
 board/kontron/sa67/rm-cfg.yaml                | 1137 +++++++
 board/kontron/sa67/sa67.c                     |  311 ++
 board/kontron/sa67/sa67.env                   |   21 +
 board/kontron/sa67/sec-cfg.yaml               |  379 +++
 board/kontron/sa67/tifs-rm-cfg.yaml           |  993 ++++++
 configs/kontron_sa67_a53_defconfig            |  211 ++
 configs/kontron_sa67_r5_defconfig             |  126 +
 doc/board/kontron/index.rst                   |    1 +
 doc/board/kontron/sa67.rst                    |   62 +
 doc/board/ti/k3.rst                           |    1 +
 drivers/gpio/gpio-uclass.c                    |   31 +-
 drivers/sysinfo/Kconfig                       |    7 +
 drivers/sysinfo/Makefile                      |    1 +
 drivers/sysinfo/sa67.c                        |  149 +
 .../arm64/ti/k3-am67a-kontron-sa67-base.dts   | 1091 +++++++
 .../arm64/ti/k3-am67a-kontron-sa67-gbe1.dtso  |   26 +
 .../arm64/ti/k3-am67a-kontron-sa67-gpios.dtso |   61 +
 .../ti/k3-am67a-kontron-sa67-rtc-rv8263.dtso  |   31 +
 include/asm-generic/gpio.h                    |    4 +
 include/configs/kontron_sa67.h                |   13 +
 include/sysinfo/sa67.h                        |   21 +
 36 files changed, 11014 insertions(+), 7 deletions(-)
 create mode 100644 arch/arm/dts/k3-am67a-kontron-sa67-base-u-boot.dtsi
 create mode 100644 arch/arm/dts/k3-am67a-kontron-sa67-binman.dtsi
 create mode 100644 arch/arm/dts/k3-am67a-kontron-sa67-ddr-mt53e256m32d1ks.dtsi
 create mode 100644 arch/arm/dts/k3-am67a-kontron-sa67-ddr-mt53e2g32d4de.dtsi
 create mode 100644 arch/arm/dts/k3-am67a-r5-kontron-sa67-mt53e256m32d1ks.dts
 create mode 100644 arch/arm/dts/k3-am67a-r5-kontron-sa67-mt53e2g32d4de.dts
 create mode 100644 arch/arm/dts/k3-am67a-r5-kontron-sa67.dtsi
 create mode 100644 board/kontron/sa67/Kconfig
 create mode 100644 board/kontron/sa67/MAINTAINERS
 create mode 100644 board/kontron/sa67/Makefile
 create mode 100644 board/kontron/sa67/board-cfg.yaml
 create mode 100644 board/kontron/sa67/common.c
 create mode 100644 board/kontron/sa67/pm-cfg.yaml
 create mode 100644 board/kontron/sa67/r5.c
 create mode 100644 board/kontron/sa67/rm-cfg.yaml
 create mode 100644 board/kontron/sa67/sa67.c
 create mode 100644 board/kontron/sa67/sa67.env
 create mode 100644 board/kontron/sa67/sec-cfg.yaml
 create mode 100644 board/kontron/sa67/tifs-rm-cfg.yaml
 create mode 100644 configs/kontron_sa67_a53_defconfig
 create mode 100644 configs/kontron_sa67_r5_defconfig
 create mode 100644 doc/board/kontron/sa67.rst
 create mode 100644 drivers/sysinfo/sa67.c
 create mode 100644 dts/upstream/src/arm64/ti/k3-am67a-kontron-sa67-base.dts
 create mode 100644 dts/upstream/src/arm64/ti/k3-am67a-kontron-sa67-gbe1.dtso
 create mode 100644 dts/upstream/src/arm64/ti/k3-am67a-kontron-sa67-gpios.dtso
 create mode 100644 dts/upstream/src/arm64/ti/k3-am67a-kontron-sa67-rtc-rv8263.dtso
 create mode 100644 include/configs/kontron_sa67.h
 create mode 100644 include/sysinfo/sa67.h
Signature · 1 line
2.47.3
#1 lore raw

PATCH 1/4 arm64: dts: ti: Add support for Kontron SMARC-sAM67

Add device tree support for the Kontron SMARC-sAM67 module, which is based on a TI AM67A SoC.

The module features:
* Quad-core AM67A94 at 1.4GHz with 8 GiB RAM
* 64 GiB eMMC, 4 MiB SPI flash for failsafe booting
* Dedicated RTC
* Multiple interfaces: 4x UART, 2x USB 2.0/USB 3.2, 2x GBE, QSPI,

        7x I2C,

* Display support: 2x LVDS, 1x DSI (*), 1x DP (*)
* Camera support: 4x CSI (*)
* Onboard microcontroller for boot control, failsafe booting and external watchdog

(*) not yet supported by the kernel

There is a base device tree and overlays which will add optional features. At the moment there is one full featured variant of that board whose device tree is generated during build by merging all the device tree overlays.

[ upstream commit: 1c3c4df06f9dee41bff60b93d9f0e67500f798f7 ]

(cherry picked from commit f9f296f96ac69e15bb3524fb66aeff9867d719d5)

---
 .../arm64/ti/k3-am67a-kontron-sa67-base.dts   | 1091 +++++++++++++++++
 .../arm64/ti/k3-am67a-kontron-sa67-gbe1.dtso  |   26 +
 .../arm64/ti/k3-am67a-kontron-sa67-gpios.dtso |   61 +
 .../ti/k3-am67a-kontron-sa67-rtc-rv8263.dtso  |   31 +
 4 files changed, 1209 insertions(+)
 create mode 100644 dts/upstream/src/arm64/ti/k3-am67a-kontron-sa67-base.dts
 create mode 100644 dts/upstream/src/arm64/ti/k3-am67a-kontron-sa67-gbe1.dtso
 create mode 100644 dts/upstream/src/arm64/ti/k3-am67a-kontron-sa67-gpios.dtso
 create mode 100644 dts/upstream/src/arm64/ti/k3-am67a-kontron-sa67-rtc-rv8263.dtso
dts/upstream/src/arm64/ti/k3-am67a-kontron-sa67-base.dts new file +1091 -0
new file mode 100644
index 00000000000..7169d934ada
@@ -0,0 +1,1091 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * Kontron SMARC-sAM67 module
+ *
+ * Copyright (c) 2025 Kontron Europe GmbH
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy.h>
+#include "k3-j722s.dtsi"
+#include "k3-serdes.h"
+
+/ {
+	compatible = "kontron,sa67", "ti,j722s";
+	model = "Kontron SMARC-sAM67";
+
+	aliases {
+		serial0 = &mcu_uart0;
+		serial1 = &main_uart0;
+		serial2 = &main_uart5;
+		serial3 = &wkup_uart0;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+		rtc0 = &wkup_rtc0;
+	};
+
+	lcd0_backlight: backlight-1 {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd0_backlight_pins_default>;
+		pwms = <&epwm1 0 50000 0>;
+		brightness-levels = <0 32 64 96 128 160 192 224 255>;
+		default-brightness-level = <8>;
+		enable-gpios = <&main_gpio0 29 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+
+	lcd1_backlight: backlight-2 {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd1_backlight_pins_default>;
+		pwms = <&epwm1 1 50000 0>;
+		brightness-levels = <0 32 64 96 128 160 192 224 255>;
+		default-brightness-level = <8>;
+		enable-gpios = <&main_gpio1 18 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
+
+	connector-1 {
+		compatible = "gpio-usb-b-connector", "usb-b-connector";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb0_connector_pins_default>;
+		type = "micro";
+		id-gpios = <&main_gpio0 34 GPIO_ACTIVE_HIGH>;
+		vbus-supply = <&vcc_usb0_vbus>;
+
+		port  {
+			usb0_connector: endpoint {
+				remote-endpoint = <&usb0_hc>;
+			};
+		};
+
+	};
+
+	memory@80000000 {
+		/* Filled in by bootloader */
+		reg = <0x00000000 0x00000000 0x00000000 0x00000000>,
+		      <0x00000000 0x00000000 0x00000000 0x00000000>;
+		device_type = "memory";
+		bootph-pre-ram;
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x10000000>;
+			alignment = <0x2000>;
+			linux,cma-default;
+		};
+
+		secure_tfa_ddr: tfa@9e780000 {
+			reg = <0x00 0x9e780000 0x00 0x80000>;
+			no-map;
+		};
+
+		secure_ddr: optee@9e800000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_memory_region: r5f-memory@a0100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa0100000 0x00 0xf00000>;
+			no-map;
+		};
+	};
+
+	vin_5p0: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_3V0_5V25_IN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		bootph-all;
+	};
+
+	vcc_3p3_s5: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_3V3_S5";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vin_5p0>;
+		regulator-always-on;
+		regulator-boot-on;
+		bootph-all;
+	};
+
+	vcc_1p8_s5: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_1V8_S5";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vin_5p0>;
+		regulator-always-on;
+		regulator-boot-on;
+		bootph-all;
+	};
+
+	vcc_3p3_s0: regulator-4 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_3V3_S0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3p3_s5>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpios = <&tps652g1 1 GPIO_ACTIVE_HIGH>;
+		bootph-all;
+	};
+
+	vcc_3p3_sd_s0: regulator-5 {
+		compatible = "regulator-fixed";
+		regulator-name = "SDIO_PWR_EN";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc_3p3_sd_s0_pins_default>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpios = <&main_gpio0 7 GPIO_ACTIVE_HIGH>;
+		bootph-all;
+	};
+
+	vcc_3p3_sd_vio_s0: regulator-6 {
+		compatible = "regulator-gpio";
+		regulator-name = "V_3V3_1V8_SD_S0";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc_3p3_sd_vio_s0_pins_default>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3p3_s0>;
+		regulator-boot-on;
+		enable-gpios = <&main_gpio0 7 GPIO_ACTIVE_HIGH>;
+		gpios = <&main_gpio0 8 GPIO_ACTIVE_HIGH>;
+		states = <3300000 0x0>,
+			 <1800000 0x1>;
+		bootph-all;
+	};
+
+	vcc_3p3_cam_s0: regulator-7 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_3V3_CAM_S0";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc_3p3_cam_s0_pins_default>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3p3_s5>;
+		enable-active-high;
+		interrupts-extended = <&main_gpio1 30 IRQ_TYPE_EDGE_FALLING>;
+		bootph-all;
+	};
+
+	vcc_1p1_s0: regulator-8 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_1V1_S0";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&vcc_1p1_s3>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		/* shared with V_0V75_0V85_CORE_S0 */
+		gpios = <&tps652g1 4 GPIO_ACTIVE_HIGH>;
+		bootph-all;
+	};
+
+	vcc_0p85_vcore_s0: regulator-9 {
+		compatible = "regulator-fixed";
+		regulator-name = "V_0V75_0V85_CORE_S0";
+		regulator-min-microvolt = <850000>;
+		regulator-max-microvolt = <850000>;
+		vin-supply = <&vin_5p0>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpios = <&tps652g1 4 GPIO_ACTIVE_HIGH>;
+		bootph-all;
+	};
+
+	vcc_lcd0_panel: regulator-10 {
+		compatible = "regulator-fixed";
+		regulator-name = "LCD0_VDD_EN";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc_lcd0_panel_pins_default>;
+		enable-active-high;
+		gpios = <&main_gpio0 30 GPIO_ACTIVE_HIGH>;
+	};
+
+	vcc_lcd1_panel: regulator-11 {
+		compatible = "regulator-fixed";
+		regulator-name = "LCD1_VDD_EN";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc_lcd1_panel_pins_default>;
+		enable-active-high;
+		gpios = <&main_gpio1 19 GPIO_ACTIVE_HIGH>;
+	};
+
+	vcc_usb0_vbus: regulator-12 {
+		compatible = "regulator-fixed";
+		regulator-name = "USB0_EN_OC#";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc_usb0_vbus_pins_default>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpios = <&main_gpio1 50 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&audio_refclk0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_refclk0_pins_default>;
+	status = "disabled";
+};
+
+&audio_refclk1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_refclk1_pins_default>;
+	status = "disabled";
+};
+
+&cpsw3g {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cpsw3g_pins_default>, <&rgmii1_pins_default>,
+		    <&rgmii2_pins_default>;
+	status = "okay";
+};
+
+&cpsw3g_mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cpsw3g_mdio_pins_default>;
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
+&cpsw_port1 {
+	phy-connection-type = "rgmii-id";
+	phy-handle = <&phy0>;
+	nvmem-cells = <&base_mac_address 0>;
+	nvmem-cell-names = "mac-address";
+	status = "okay";
+};
+
+&main_gpio0 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "SOC_SDIO_PWR_EN", "VSD_SEL",
+		"RESET_OUT#", "I2C_MUX_RST#", "SPI_FLASH_CS#", "QPSI_CS0#",
+		"QSPI_CS1#", "BOOT_SEL1", "BRDCFG0", "BRDCFG1", "BRDCFG2",
+		"BRDCFG3", "BRDCFG4", "", "BRDREV0", "BRDREV1", "", "", "", "",
+		"", "", "LCD0_BKLT_EN", "LCD0_VDD_EN", "GBE_INT#", "DSI0_TE",
+		"CHARGING#", "USB0_OTG_ID", "PMIC_INT#", "RTC_INT#",
+		"EDP_BRIDGE_EN", "EDP_BRIDGE_IRQ#", "", "CHARGER_PRSNT#", "",
+		"", "", "", "BOOT_SEL2#", "CAM2_RST#", "CAM2_PWR#", "",
+		"CAM3_RST#", "CAM3_PWR#", "GPIO0", "GPIO1", "", "", "", "", "",
+		"", "", "", "", "", "", "", "", "", "", "", "GPIO10", "GPIO11",
+		"SLEEP#", "LID#";
+
+	bootph-all;
+	status = "okay";
+};
+
+&main_gpio1 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "GPIO6", "GPIO7", "", "", "", "",
+		"GPIO8", "GPIO9", "PCIE_A_RST#", "", "BATLOW#", "LCD1_BKLT_EN",
+		"LCD1_VDD_EN", "", "", "", "", "GPIO2", "GPIO3", "", "",
+		"GPIO4", "GPIO5", "CAM_S0_FAULT#", "BOOT_SEL0#", "", "", "", "",
+		"", "", "", "", "", "", "", "", "", "", "", "", "SDIO_CD#", "",
+		"USB0_DRVVBUS", "USB1_DRVVBUS";
+
+	bootph-all;
+	status = "okay";
+};
+
+/* I2C_LOCAL */
+&main_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c0_pins_default>;
+	clock-frequency = <100000>;
+	bootph-all;
+	status = "okay";
+
+	tps652g1: pmic@44 {
+		compatible = "ti,tps652g1";
+		reg = <0x44>;
+		ti,primary-pmic;
+		system-power-controller;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"LPM_EN#", "EN_3V3_S0", "POWER_BTN#", "CARRIER_STBY#",
+			"EN_0V75_0V85_VCORE_S0", "PMIC_WAKEUP";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupts-extended = <&main_gpio0 35 IRQ_TYPE_EDGE_FALLING>;
+
+		buck1-supply = <&vin_5p0>;
+		buck2-supply = <&vin_5p0>;
+		buck3-supply = <&vin_5p0>;
+		buck4-supply = <&vin_5p0>;
+		ldo1-supply = <&vin_5p0>;
+		ldo2-supply = <&vin_5p0>;
+		ldo3-supply = <&vin_5p0>;
+
+		bootph-all;
+
+		regulators {
+			vcc_0p85_s0: buck1 {
+				regulator-name = "V_0V85_S0";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vcc_1p1_s3: buck2 {
+				regulator-name = "V_1V1_S3";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vcc_1p8_s0: buck3 {
+				regulator-name = "V_1V8_S0";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vcc_1p2_s0: buck4 {
+				regulator-name = "V_1V2_S0";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vcc_1p8_vda_pll_s0: ldo1 {
+				regulator-name = "V_1V8_VDA_PLL_S0";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vcc_1p8_s3: ldo2 {
+				regulator-name = "V_1V8_S3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vcc_1p8_ret_s5: ldo3 {
+				regulator-name = "V_1V8_RET_S5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	system-controller@4a {
+		compatible = "kontron,sa67mcu", "kontron,sl28cpld";
+		reg = <0x4a>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		watchdog@4 {
+			compatible = "kontron,sa67mcu-wdt", "kontron,sl28cpld-wdt";
+			reg = <0x4>;
+			kontron,assert-wdt-timeout-pin;
+		};
+
+		hwmon@8 {
+			compatible = "kontron,sa67mcu-hwmon";
+			reg = <0x8>;
+		};
+	};
+};
+
+/* I2C_CAM */
+&main_i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c2_pins_default>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_mux_pins_default>;
+
+		vdd-supply = <&vcc_1p8_s0>;
+		reset-gpios = <&main_gpio0 10 GPIO_ACTIVE_LOW>;
+
+		i2c_cam0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c_cam1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c_cam2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c_cam3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+/* I2C_LCD */
+&main_i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c3_pins_default>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&main_pmx0 {
+	audio_refclk0_pins_default: audio-refclk0-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x0c4, PIN_OUTPUT, 5)	/* (W23) VOUT0_DATA3.AUDIO_EXT_REFCLK0 */
+		>;
+	};
+
+	audio_refclk1_pins_default: audio-refclk1-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x0a0, PIN_OUTPUT, 1)	/* (N24) GPMC0_WPn.AUDIO_EXT_REFCLK1 */
+		>;
+	};
+
+	cpsw3g_mdio_pins_default: cpsw3g-mdio-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x160, PIN_OUTPUT, 0)	/* (AC24) MDIO0_MDC */
+			J722S_IOPAD(0x15c, PIN_INPUT, 0)	/* (AD25) MDIO0_MDIO */
+		>;
+	};
+
+	cpsw3g_pins_default: cpsw3g-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x1b8, PIN_OUTPUT, 1)	/* (C20) SPI0_CS1.CP_GEMAC_CPTS0_TS_COMP */
+		>;
+	};
+
+	edp_bridge_pins_default: edp-bridge-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x098, PIN_OUTPUT, 7)	/* (V21) GPMC0_WAIT0.GPIO0_37 */
+			J722S_IOPAD(0x09c, PIN_INPUT, 7)	/* (W26) GPMC0_WAIT1.GPIO0_38 */
+		>;
+	};
+
+	i2c_mux_pins_default: i2c-mux-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x028, PIN_OUTPUT, 7)	/* (M27) OSPI0_D7.GPIO0_10 */
+		>;
+	};
+
+	lcd0_backlight_pins_default: lcd0-backlight-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x074, PIN_OUTPUT, 7)	/* (V22) GPMC0_AD14.GPIO0_29 */
+			J722S_IOPAD(0x110, PIN_OUTPUT, 4)	/* (G27) MMC2_DAT1.EHRPWM1_A */
+		>;
+	};
+
+	lcd1_backlight_pins_default: lcd1-backlight-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x1c0, PIN_OUTPUT, 7)	/* (E19) SPI0_D0.GPIO1_18 */
+			J722S_IOPAD(0x114, PIN_OUTPUT, 4)	/* (G26) MMC2_DAT0.EHRPWM1_B */
+		>;
+	};
+
+	main_i2c0_pins_default: main-i2c0-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x1e0, PIN_INPUT, 0)	/* (D23) I2C0_SCL */
+			J722S_IOPAD(0x1e4, PIN_INPUT, 0)	/* (B22) I2C0_SDA */
+		>;
+		bootph-all;
+	};
+
+	main_i2c2_pins_default: main-i2c2-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x0b0, PIN_INPUT, 1)	/* (P22) GPMC0_CSn2.I2C2_SCL */
+			J722S_IOPAD(0x0b4, PIN_INPUT, 1)	/* (P23) GPMC0_CSn3.I2C2_SDA */
+		>;
+	};
+
+	main_i2c3_pins_default: main-i2c3-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x1d0, PIN_INPUT, 2)	/* (E22) UART0_CTSn.I2C3_SCL */
+			J722S_IOPAD(0x1d4, PIN_INPUT, 2)	/* (B21) UART0_RTSn.I2C3_SDA */
+		>;
+	};
+
+	main_i2c4_pins_default: main-i2c4-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x0a8, PIN_INPUT, 1)	/* (R27) GPMC0_CSn0.I2C4_SCL */
+			J722S_IOPAD(0x0ac, PIN_INPUT, 1)	/* (P21) GPMC0_CSn1.I2C4_SDA */
+		>;
+	};
+
+	main_uart0_pins_default: main-uart0-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x1c8, PIN_INPUT, 0)	/* (F19) UART0_RXD */
+			J722S_IOPAD(0x1cc, PIN_OUTPUT, 0)	/* (F20) UART0_TXD */
+		>;
+		bootph-all;
+	};
+
+	main_uart5_pins_default: main-uart5-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x108, PIN_INPUT, 3)	/* (J27) MMC2_DAT3.UART5_RXD */
+			J722S_IOPAD(0x10c, PIN_OUTPUT, 3)	/* (H27) MMC2_DAT2.UART5_TXD */
+			J722S_IOPAD(0x008, PIN_INPUT, 5)	/* (L22) OSPI0_DQS.UART5_CTSn */
+			J722S_IOPAD(0x004, PIN_OUTPUT, 5)	/* (L23) OSPI0_LBCLKO.UART5_RTSn */
+		>;
+	};
+
+	mcasp0_pins_default: mcasp0-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x1a4, PIN_INPUT, 0)	/* (D25) MCASP0_ACLKX */
+			J722S_IOPAD(0x1a8, PIN_INPUT, 0)	/* (C26) MCASP0_AFSX */
+			J722S_IOPAD(0x1a0, PIN_INPUT, 0)	/* (F23) MCASP0_AXR0 */
+			J722S_IOPAD(0x19c, PIN_OUTPUT, 0)	/* (B25) MCASP0_AXR1 */
+		>;
+	};
+
+	mcasp2_pins_default: mcasp2-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x070, PIN_INPUT, 3)	/* (V24) GPMC0_AD13.MCASP2_ACLKX */
+			J722S_IOPAD(0x06c, PIN_INPUT, 3)	/* (V26) GPMC0_AD12.MCASP2_AFSX */
+			J722S_IOPAD(0x05c, PIN_INPUT, 3)	/* (U27) GPMC0_AD8.MCASP2_AXR0 */
+			J722S_IOPAD(0x060, PIN_OUTPUT, 3)	/* (U26) GPMC0_AD9.MCASP2_AXR1 */
+		>;
+	};
+
+	oldi0_pins_default: oldi0-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x260, PIN_OUTPUT, 0)	/* (AF23) OLDI0_A0N */
+			J722S_IOPAD(0x25c, PIN_OUTPUT, 0)	/* (AG24) OLDI0_A0P */
+			J722S_IOPAD(0x268, PIN_OUTPUT, 0)	/* (AG22) OLDI0_A1N */
+			J722S_IOPAD(0x264, PIN_OUTPUT, 0)	/* (AG23) OLDI0_A1P */
+			J722S_IOPAD(0x270, PIN_OUTPUT, 0)	/* (AB20) OLDI0_A2N */
+			J722S_IOPAD(0x26c, PIN_OUTPUT, 0)	/* (AB21) OLDI0_A2P */
+			J722S_IOPAD(0x278, PIN_OUTPUT, 0)	/* (AG20) OLDI0_A3N */
+			J722S_IOPAD(0x274, PIN_OUTPUT, 0)	/* (AG21) OLDI0_A3P */
+			J722S_IOPAD(0x2a0, PIN_OUTPUT, 0)	/* (AF21) OLDI0_CLK0N */
+			J722S_IOPAD(0x29c, PIN_OUTPUT, 0)	/* (AE20) OLDI0_CLK0P */
+		>;
+	};
+
+	oldi1_pins_default: oldi1-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x280, PIN_OUTPUT, 0)	/* (AD21) OLDI0_A4N */
+			J722S_IOPAD(0x27c, PIN_OUTPUT, 0)	/* (AC21) OLDI0_A4P */
+			J722S_IOPAD(0x288, PIN_OUTPUT, 0)	/* (AF19) OLDI0_A5N */
+			J722S_IOPAD(0x284, PIN_OUTPUT, 0)	/* (AF18) OLDI0_A5P */
+			J722S_IOPAD(0x290, PIN_OUTPUT, 0)	/* (AG17) OLDI0_A6N */
+			J722S_IOPAD(0x28c, PIN_OUTPUT, 0)	/* (AG18) OLDI0_A6P */
+			J722S_IOPAD(0x298, PIN_OUTPUT, 0)	/* (AB19) OLDI0_A7N */
+			J722S_IOPAD(0x294, PIN_OUTPUT, 0)	/* (AA20) OLDI0_A7P */
+			J722S_IOPAD(0x2a8, PIN_OUTPUT, 0)	/* (AD20) OLDI0_CLK1N */
+			J722S_IOPAD(0x2a4, PIN_OUTPUT, 0)	/* (AE19) OLDI0_CLK1P */
+		>;
+	};
+
+	ospi0_pins_default: ospi0-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x000, PIN_OUTPUT, 0)	/* (L24) OSPI0_CLK */
+			J722S_IOPAD(0x02c, PIN_OUTPUT, 0)	/* (K26) OSPI0_CSn0 */
+			J722S_IOPAD(0x030, PIN_OUTPUT, 0)	/* (K23) OSPI0_CSn1 */
+			J722S_IOPAD(0x034, PIN_OUTPUT, 0)	/* (K22) OSPI0_CSn2 */
+			J722S_IOPAD(0x00c, PIN_INPUT, 0)	/* (K27) OSPI0_D0 */
+			J722S_IOPAD(0x010, PIN_INPUT, 0)	/* (L27) OSPI0_D1 */
+			J722S_IOPAD(0x014, PIN_INPUT, 0)	/* (L26) OSPI0_D2 */
+			J722S_IOPAD(0x018, PIN_INPUT, 0)	/* (L25) OSPI0_D3 */
+		>;
+		bootph-all;
+	};
+
+	pcie0_rc_pins_default: pcie0-rc-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x2ac, PIN_OUTPUT, 0)	/* (F25) PCIE0_CLKREQn */
+			J722S_IOPAD(0x1b4, PIN_OUTPUT, 7)	/* (B20) SPI0_CS0.GPIO1_15 */
+		>;
+	};
+
+	pmic_irq_pins_default: pmic-irq-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x090, PIN_INPUT, 7)	/* (P27) GPMC0_BE0n_CLE.GPIO0_35 */
+		>;
+	};
+
+	rgmii1_pins_default: rgmii1-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x14c, PIN_INPUT, 0)	/* (AC25) RGMII1_RD0 */
+			J722S_IOPAD(0x150, PIN_INPUT, 0)	/* (AD27) RGMII1_RD1 */
+			J722S_IOPAD(0x154, PIN_INPUT, 0)	/* (AE24) RGMII1_RD2 */
+			J722S_IOPAD(0x158, PIN_INPUT, 0)	/* (AE26) RGMII1_RD3 */
+			J722S_IOPAD(0x148, PIN_INPUT, 0)	/* (AE27) RGMII1_RXC */
+			J722S_IOPAD(0x144, PIN_INPUT, 0)	/* (AD23) RGMII1_RX_CTL */
+			J722S_IOPAD(0x134, PIN_OUTPUT, 0)	/* (AF27) RGMII1_TD0 */
+			J722S_IOPAD(0x138, PIN_OUTPUT, 0)	/* (AE23) RGMII1_TD1 */
+			J722S_IOPAD(0x13c, PIN_OUTPUT, 0)	/* (AG25) RGMII1_TD2 */
+			J722S_IOPAD(0x140, PIN_OUTPUT, 0)	/* (AF24) RGMII1_TD3 */
+			J722S_IOPAD(0x130, PIN_OUTPUT, 0)	/* (AG26) RGMII1_TXC */
+			J722S_IOPAD(0x12c, PIN_OUTPUT, 0)	/* (AF25) RGMII1_TX_CTL */
+		>;
+	};
+
+	rgmii2_pins_default: rgmii2-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x0f8, PIN_INPUT, 2)	/* (AB24) VOUT0_HSYNC.RGMII2_RD0 */
+			J722S_IOPAD(0x0fc, PIN_INPUT, 2)	/* (AC27) VOUT0_DE.RGMII2_RD1 */
+			J722S_IOPAD(0x100, PIN_INPUT, 2)	/* (AB23) VOUT0_VSYNC.RGMII2_RD2 */
+			J722S_IOPAD(0x104, PIN_INPUT, 2)	/* (AC26) VOUT0_PCLK.RGMII2_RD3 */
+			J722S_IOPAD(0x0f4, PIN_INPUT, 2)	/* (AB27) VOUT0_DATA15.RGMII2_RXC */
+			J722S_IOPAD(0x0f0, PIN_INPUT, 2)	/* (AB26) VOUT0_DATA14.RGMII2_RX_CTL */
+			J722S_IOPAD(0x0e0, PIN_OUTPUT, 2)	/* (AA25) VOUT0_DATA10.RGMII2_TD0 */
+			J722S_IOPAD(0x0e4, PIN_OUTPUT, 2)	/* (AB25) VOUT0_DATA11.RGMII2_TD1 */
+			J722S_IOPAD(0x0e8, PIN_OUTPUT, 2)	/* (AA23) VOUT0_DATA12.RGMII2_TD2 */
+			J722S_IOPAD(0x0ec, PIN_OUTPUT, 2)	/* (AA22) VOUT0_DATA13.RGMII2_TD3 */
+			J722S_IOPAD(0x0dc, PIN_OUTPUT, 2)	/* (AA27) VOUT0_DATA9.RGMII2_TXC */
+			J722S_IOPAD(0x0d8, PIN_OUTPUT, 2)	/* (AA24) VOUT0_DATA8.RGMII2_TX_CTL */
+		>;
+	};
+
+	rtc_pins_default: rtc-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x094, PIN_INPUT, 7)	/* (P26) GPMC0_BE1n.GPIO0_36 */
+		>;
+	};
+
+	sdhci1_pins_default: sdhci1-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x23c, PIN_INPUT, 0)	/* (H22) MMC1_CMD */
+			J722S_IOPAD(0x234, PIN_OUTPUT, 0)	/* (H24) MMC1_CLK */
+			J722S_IOPAD(0x230, PIN_INPUT, 0)	/* (H23) MMC1_DAT0 */
+			J722S_IOPAD(0x22c, PIN_INPUT, 0)	/* (H20) MMC1_DAT1 */
+			J722S_IOPAD(0x228, PIN_INPUT, 0)	/* (J23) MMC1_DAT2 */
+			J722S_IOPAD(0x224, PIN_INPUT, 0)	/* (H25) MMC1_DAT3 */
+			J722S_IOPAD(0x240, PIN_INPUT, 0)	/* (B24) MMC1_SDCD */
+			J722S_IOPAD(0x244, PIN_INPUT, 0)	/* (A24) MMC1_SDWP */
+		>;
+		bootph-all;
+	};
+
+	usb0_connector_pins_default: usb0-connector-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x08c, PIN_INPUT_PULLUP, 7)	/* (N23) GPMC0_WEn.GPIO0_34 */
+		>;
+	};
+
+	usb1_pins_default: usb1-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x258, PIN_OUTPUT, 0)	/* (B27) USB1_DRVVBUS */
+		>;
+	};
+
+	vcc_3p3_sd_s0_pins_default: vcc-3p3-sd-s0-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x01c, PIN_OUTPUT, 7)	/* (L21) OSPI0_D4.GPIO0_7 */
+		>;
+		bootph-all;
+	};
+
+	vcc_3p3_sd_vio_s0_pins_default: vcc-3p3-sd-vio-s0-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x020, PIN_OUTPUT, 7)	/* (M26) OSPI0_D5.GPIO0_8 */
+		>;
+		bootph-all;
+	};
+
+	vcc_3p3_cam_s0_pins_default: vcc-3p3-cam-s0-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x1f0, PIN_OUTPUT, 7)	/* (A23) EXT_REFCLK1.GPIO1_30 */
+		>;
+	};
+
+	vcc_lcd0_panel_pins_default: vcc-lcd0-panel-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x078, PIN_OUTPUT, 7)	/* (V23) GPMC0_AD15.GPIO0_30 */
+		>;
+	};
+
+	vcc_lcd1_panel_pins_default: vcc-lcd1-panel-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x1c4, PIN_OUTPUT, 7)	/* (E20) SPI0_D1.GPIO1_19 */
+		>;
+	};
+
+	vcc_usb0_vbus_pins_default: vcc-usb0-vbus-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x254, PIN_OUTPUT, 7)	/* (E25) USB0_DRVVBUS.GPIO1_50 */
+		>;
+	};
+};
+
+/* SER1 */
+&main_uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart0_pins_default>;
+	bootph-all;
+	status = "okay";
+};
+
+/* SER2 */
+&main_uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart5_pins_default>;
+	bootph-all;
+	status = "okay";
+};
+
+/* I2S0 */
+&mcasp0 {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcasp0_pins_default>;
+	op-mode = <0>; /* I2S */
+	tdm-slots = <2>;
+	serial-dir = <2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
+};
+
+/* I2S2 */
+&mcasp2 {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcasp2_pins_default>;
+	op-mode = <0>; /* I2S */
+	tdm-slots = <2>;
+	serial-dir = <2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
+};
+
+/* CAN0 */
+&mcu_mcan0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_mcan0_pins_default>;
+	status = "okay";
+};
+
+/* CAN1 */
+&mcu_mcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_mcan1_pins_default>;
+	status = "okay";
+};
+
+&mcu_gpio0 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "", "", "", "", /* 10 */ "GPIO12",
+		"MCU_INT#", "", "", "", "", "", "", "", "", "", "", "GPIO13";
+};
+
+/* I2C_GP */
+&mcu_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_i2c0_pins_default>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	/* SMARC Module EEPROM */
+	eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+		pagesize = <32>;
+		vcc-supply = <&vcc_1p8_s0>;
+	};
+};
+
+&mcu_pmx0 {
+	mcu_i2c0_pins_default: mcu-i2c0-default-pins {
+		pinctrl-single,pins = <
+			J722S_MCU_IOPAD(0x044, PIN_INPUT, 0)	/* (B13) MCU_I2C0_SCL */
+			J722S_MCU_IOPAD(0x048, PIN_INPUT, 0)	/* (E11) MCU_I2C0_SDA */
+		>;
+	};
+	mcu_mcan0_pins_default: mcu-mcan0-default-pins {
+		pinctrl-single,pins = <
+			J722S_MCU_IOPAD(0x038, PIN_INPUT, 0)	/* (D8) MCU_MCAN0_RX */
+			J722S_MCU_IOPAD(0x034, PIN_OUTPUT, 0)	/* (B2) MCU_MCAN0_TX */
+		>;
+	};
+
+	mcu_mcan1_pins_default: mcu-mcan1-default-pins {
+		pinctrl-single,pins = <
+			J722S_MCU_IOPAD(0x040, PIN_INPUT, 0)	/* (B1) MCU_MCAN1_RX */
+			J722S_MCU_IOPAD(0x03c, PIN_OUTPUT, 0)	/* (C1) MCU_MCAN1_TX */
+		>;
+	};
+
+	mcu_uart0_pins_default: mcu-uart0-default-pins {
+		pinctrl-single,pins = <
+			J722S_MCU_IOPAD(0x014, PIN_INPUT, 0)	/* (B8) MCU_UART0_RXD */
+			J722S_MCU_IOPAD(0x018, PIN_OUTPUT, 0)	/* (B4) MCU_UART0_TXD */
+			J722S_MCU_IOPAD(0x01c, PIN_INPUT, 0)	/* (B5) MCU_UART0_CTSn */
+			J722S_MCU_IOPAD(0x020, PIN_OUTPUT, 0)	/* (C5) MCU_UART0_RTSn */
+		>;
+		bootph-all;
+	};
+
+	mcu_spi0_pins_default: mcu-spi0-default-pins {
+		pinctrl-single,pins = <
+			J722S_MCU_IOPAD(0x008, PIN_OUTPUT, 0)	/* (A9) MCU_SPI0_CLK */
+			J722S_MCU_IOPAD(0x000, PIN_OUTPUT, 0)	/* (C12) MCU_SPI0_CS0 */
+			J722S_MCU_IOPAD(0x004, PIN_OUTPUT, 0)	/* (A10) MCU_SPI0_CS1 */
+			J722S_MCU_IOPAD(0x00c, PIN_INPUT, 0)	/* (B12) MCU_SPI0_D0 */
+			J722S_MCU_IOPAD(0x010, PIN_OUTPUT, 0)	/* (C11) MCU_SPI0_D1 */
+		>;
+	};
+
+	wkup_uart0_pins_default: wkup-uart0-default-pins {
+		pinctrl-single,pins = <
+			J722S_MCU_IOPAD(0x024, PIN_INPUT, 0)	/* (B3) WKUP_UART0_RXD */
+			J722S_MCU_IOPAD(0x028, PIN_OUTPUT, 0)	/* (C8) WKUP_UART0_TXD */
+		>;
+		bootph-all;
+	};
+
+	wkup_i2c0_pins_default: wkup-i2c0-default-pins {
+		pinctrl-single,pins = <
+			J722S_MCU_IOPAD(0x04c, PIN_INPUT, 0)	/* (B9) WKUP_I2C0_SCL */
+			J722S_MCU_IOPAD(0x050, PIN_INPUT, 0)	/* (D11) WKUP_I2C0_SDA */
+		>;
+	};
+};
+
+/* SPI0 */
+&mcu_spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_spi0_pins_default>;
+};
+
+/* SER0 */
+&mcu_uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_uart0_pins_default>;
+	bootph-all;
+	status = "okay";
+};
+
+/* QSPI0 */
+&ospi0 {
+	pinctrl-0 = <&ospi0_pins_default>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <104000000>;
+		spi-rx-bus-width = <2>;
+		spi-tx-bus-width = <2>;
+		m25p,fast-read;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <3>;
+		vcc-supply = <&vcc_1p8_s0>;
+		bootph-all;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				reg = <0x000000 0x400000>;
+				label = "failsafe bootloader";
+				read-only;
+			};
+		};
+
+		otp-1 {
+			compatible = "user-otp";
+
+			nvmem-layout {
+				compatible = "kontron,sa67-vpd", "kontron,sl28-vpd";
+
+				serial_number: serial-number {
+				};
+
+				base_mac_address: base-mac-address {
+					#nvmem-cell-cells = <1>;
+				};
+			};
+		};
+	};
+};
+
+&pcie0_rc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie0_rc_pins_default>;
+
+	/*
+	 * This is low active, but the driver itself is broken and already
+	 * inverts the logic.
+	 */
+	reset-gpios = <&main_gpio1 15 GPIO_ACTIVE_HIGH>;
+	phys = <&serdes1_pcie>;
+	phy-names = "pcie-phy";
+	status = "okay";
+};
+
+&sdhci0 {
+	disable-wp;
+	bootph-all;
+	ti,driver-strength-ohm = <50>;
+	status = "okay";
+};
+
+/* SDIO */
+&sdhci1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhci1_pins_default>;
+	vmmc-supply = <&vcc_3p3_sd_s0>;
+	vqmmc-supply = <&vcc_3p3_sd_vio_s0>;
+	bootph-all;
+	cd-gpios = <&main_gpio1 48 GPIO_ACTIVE_LOW>;
+	cd-debounce-delay-ms = <100>;
+	ti,fails-without-test-cd;
+	ti,driver-strength-ohm = <50>;
+	status = "okay";
+};
+
+&serdes_ln_ctrl {
+	idle-states = <J722S_SERDES0_LANE0_USB>,
+		      <J722S_SERDES1_LANE0_PCIE0_LANE0>;
+};
+
+&serdes_wiz0 {
+	status = "okay";
+};
+
+&serdes_wiz1 {
+	status = "okay";
+};
+
+&serdes0 {
+	serdes0_usb3: phy@0 {
+		reg = <0>;
+		#phy-cells = <0>;
+		resets = <&serdes_wiz0 1>;
+		cdns,num-lanes = <1>;
+		cdns,phy-type = <PHY_TYPE_USB3>;
+	};
+};
+
+&serdes1 {
+	serdes1_pcie: phy@0 {
+		reg = <0>;
+		#phy-cells = <0>;
+		resets = <&serdes_wiz1 1>;
+		cdns,num-lanes = <1>;
+		cdns,phy-type = <PHY_TYPE_PCIE>;
+	};
+};
+
+&usb0 {
+	/* dual role is implemented but not a full featured OTG */
+	adp-disable;
+	hnp-disable;
+	srp-disable;
+	dr_mode = "otg";
+	usb-role-switch;
+	role-switch-default-mode = "peripheral";
+	status = "okay";
+
+	port {
+		usb0_hc: endpoint {
+			remote-endpoint = <&usb0_connector>;
+		};
+	};
+};
+
+&usb0_phy_ctrl {
+	/*
+	 * Keep this node in the SPL to be able to use the USB controller to
+	 * boot via DFU.
+	 */
+	bootph-all;
+};
+
+&usb1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins_default>;
+
+	dr_mode = "host";
+	maximum-speed = "super-speed";
+	phys = <&serdes0_usb3>;
+	phy-names = "cdns3,usb3-phy";
+};
+
+&usbss0 {
+	ti,vbus-divider;
+	status = "okay";
+};
+
+&usbss1 {
+	ti,vbus-divider;
+	status = "okay";
+};
+
+/* I2C_PM */
+&wkup_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_i2c0_pins_default>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+/* SER3 */
+&wkup_uart0 {
+	/* WKUP UART0 is used by Device Manager firmware */
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_uart0_pins_default>;
+	bootph-all;
+	status = "reserved";
+};
dts/upstream/src/arm64/ti/k3-am67a-kontron-sa67-gbe1.dtso new file +26 -0
new file mode 100644
index 00000000000..5dfb0b8f10d
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * Second ethernet port GBE1.
+ *
+ * Copyright (c) 2025 Kontron Europe GmbH
+ */
+
+/dts-v1/;
+/plugin/;
+
+&cpsw3g_mdio {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
+&cpsw_port2 {
+	phy-connection-type = "rgmii-id";
+	phy-handle = <&phy1>;
+	nvmem-cells = <&base_mac_address 1>;
+	nvmem-cell-names = "mac-address";
+	status = "okay";
+};
dts/upstream/src/arm64/ti/k3-am67a-kontron-sa67-gpios.dtso new file +61 -0

61 lines not on this page · raw message

dts/upstream/src/arm64/ti/k3-am67a-kontron-sa67-rtc-rv8263.dtso new file +31 -0
new file mode 100644
index 00000000000..0a3e9f614c4
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * Microcrystal RV8263 RTC variant.
+ *
+ * Copyright (c) 2025 Kontron Europe GmbH
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&{/} {
+	aliases {
+		rtc0 = "/bus@f0000/i2c@20000000/rtc@51"; /* &rtc */
+		rtc1 = "/bus@f0000/bus@b00000/rtc@2b1f0000"; /* &wkup_rtc0 */
+	};
+};
+
+&main_i2c0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	rtc: rtc@51 {
+		compatible = "microcrystal,rv8263";
+		reg = <0x51>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&rtc_pins_default>;
+		interrupts-extended = <&main_gpio0 36 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
Signature · 1 line
2.47.3
#2 lore raw

PATCH 2/4 gpio: 3way strapping: add pinctrl method

In reply to Michael Walle

There are GPIO controllers which only supports static pinctrl configurations to enable pull-up or pull-downs. E.g. that is common on the k3 SoCs.

To switch between pull-up and pull-down, the device tree has to provide a pinctrl configuration for both. These are then applied at once.

---
 drivers/gpio/gpio-uclass.c | 31 ++++++++++++++++++++++++-------
 include/asm-generic/gpio.h |  4 ++++
 2 files changed, 28 insertions(+), 7 deletions(-)
drivers/gpio/gpio-uclass.c +24 -7
index 38151ef1bee..ab29a38d24b 100644
@@ -12,6 +12,7 @@
 #include <dm/device_compat.h>
 #include <dm/device-internal.h>
 #include <dm/lists.h>
+#include <dm/pinctrl.h>
 #include <dm/uclass-internal.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <errno.h>
@@ -1043,8 +1044,9 @@ int dm_gpio_get_values_as_int(const struct gpio_desc *desc_list, int count)
 	return vector;
 }
 
-int dm_gpio_get_values_as_int_base3(struct gpio_desc *desc_list,
-				    int count)
+int dm_gpio_get_values_as_int_base3_pctrl(struct udevice *pinctrl,
+					  struct gpio_desc *desc_list,
+					  int count)
 {
 	static const char tristate[] = "01z";
 	enum {
@@ -1065,11 +1067,20 @@ int dm_gpio_get_values_as_int_base3(struct gpio_desc *desc_list,
 	assert(count < 20);
 
 	for (i = 0; i < NUM_OPTIONS; i++) {
-		uint flags = GPIOD_IS_IN;
-
-		flags |= (i == PULLDOWN) ? GPIOD_PULL_DOWN : GPIOD_PULL_UP;
-		ret = dm_gpios_clrset_flags(desc_list, count, GPIOD_MASK_PULL,
-					    flags);
+		if (CONFIG_IS_ENABLED(PINCTRL) && pinctrl) {
+			const char *state = (i == PULLDOWN) ? "pull-down" :
+							      "pull-up";
+			ret = pinctrl_select_state(pinctrl, state);
+		} else if (pinctrl) {
+			return log_msg_ret("no pinctrl", -EINVAL);
+		} else {
+			uint flags = GPIOD_IS_IN;
+
+			flags |= (i == PULLDOWN) ? GPIOD_PULL_DOWN :
+						   GPIOD_PULL_UP;
+			ret = dm_gpios_clrset_flags(desc_list, count,
+						    GPIOD_MASK_PULL, flags);
+		}
 		if (ret)
 			return log_msg_ret("pu", ret);
 
@@ -1108,6 +1119,12 @@ int dm_gpio_get_values_as_int_base3(struct gpio_desc *desc_list,
 	return vector;
 }
 
+int dm_gpio_get_values_as_int_base3(struct gpio_desc *desc_list,
+				    int count)
+{
+	return dm_gpio_get_values_as_int_base3_pctrl(NULL, desc_list, count);
+}
+
 /**
  * gpio_request_tail: common work for requesting a gpio.
  *
include/asm-generic/gpio.h +4 -0
index a21c606f2b8..a69b8144973 100644
@@ -525,6 +525,10 @@ int dm_gpio_get_values_as_int(const struct gpio_desc *desc_list, int count);
 int dm_gpio_get_values_as_int_base3(struct gpio_desc *desc_list,
 				    int count);
 
+int dm_gpio_get_values_as_int_base3_pctrl(struct udevice *pinctrl,
+					  struct gpio_desc *desc_list,
+					  int count);
+
 /**
  * gpio_claim_vector() - claim a number of GPIOs for input
  *
Signature · 1 line
2.47.3
#3 lore raw

PATCH 3/4 sysinfo: add driver for the Kontron SMARC-sAM67 board

In reply to Michael Walle

The board has 3way strapping pins which are used to encode the board variants. I.e. if it has a second ethernet interface or which RTC is available.

Add a driver to query that information. The board code will use that information to skip any unrelated device tree overlay. In the future, this can also be used to select the correct base device tree.

---
 drivers/sysinfo/Kconfig  |   7 ++
 drivers/sysinfo/Makefile |   1 +
 drivers/sysinfo/sa67.c   | 149 +++++++++++++++++++++++++++++++++++++++
 include/sysinfo/sa67.h   |  21 ++++++
 4 files changed, 178 insertions(+)
 create mode 100644 drivers/sysinfo/sa67.c
 create mode 100644 include/sysinfo/sa67.h
drivers/sysinfo/Kconfig +7 -0
index df83df69ffb..0ba2e249430 100644
@@ -31,6 +31,13 @@ config SYSINFO_RCAR3
 	help
 	  Support querying SoC version information for Renesas R-Car Gen3.
 
+config SYSINFO_SA67
+	bool "Enable sysinfo driver for the Kontron SMARC-sA67 board"
+	depends on TARGET_J722S_A53_SA67 || TARGET_J722S_R5_SA67
+	help
+	  Support querying board strapping options for the Kontron SMARC-sa67
+	  board.
+
 config SYSINFO_IOT2050
 	bool "Enable sysinfo driver for the Siemens IOT2050"
 	depends on TARGET_IOT2050_A53
drivers/sysinfo/Makefile +1 -0
index 26ca3150999..541a4456b56 100644
@@ -7,5 +7,6 @@ obj-$(CONFIG_SYSINFO_GAZERBEAM) += gazerbeam.o
 obj-$(CONFIG_SYSINFO_GPIO) += gpio.o
 obj-$(CONFIG_SYSINFO_IOT2050) += iot2050.o
 obj-$(CONFIG_SYSINFO_RCAR3) += rcar3.o
+obj-$(CONFIG_SYSINFO_SA67) += sa67.o
 obj-$(CONFIG_SYSINFO_SANDBOX) += sandbox.o
 obj-$(CONFIG_SYSINFO_SMBIOS) += smbios.o
drivers/sysinfo/sa67.c new file +149 -0

149 lines not on this page · raw message

include/sysinfo/sa67.h new file +21 -0
new file mode 100644
index 00000000000..28b87268e44
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+
+#ifndef __SYSINFO_SA67_H
+#define __SYSINFO_SA67_H
+
+#include <sysinfo.h>
+
+enum {
+	BOARD_REVISION = SYSID_BOARD_MODEL,
+	BOARD_CFG = SYSID_USER,
+	BOARD_MEMORY,
+	BOARD_HAS_GBE1,
+	BOARD_HAS_LVDS1,
+	BOARD_HAS_DP0,
+	BOARD_HAS_EDP1,
+	BOARD_HAS_DSI1,
+	BOARD_HAS_RTC_RV3032,
+	BOARD_HAS_RTC_RV8263,
+};
+
+#endif /* __SYSINFO_SA67_H */
Signature · 1 line
2.47.3
#4 lore raw

PATCH 4/4 board: kontron: initial commit for the SMARC-sAM67

In reply to Michael Walle

Add support for the Kontron SMARC-sAM67 module which is based on the TI AM67A SoC.

---
 .../k3-am67a-kontron-sa67-base-u-boot.dtsi    |  127 +
 .../arm/dts/k3-am67a-kontron-sa67-binman.dtsi |  202 ++
 ...m67a-kontron-sa67-ddr-mt53e256m32d1ks.dtsi | 2797 +++++++++++++++++
 ...-am67a-kontron-sa67-ddr-mt53e2g32d4de.dtsi | 2797 +++++++++++++++++
 ...-am67a-r5-kontron-sa67-mt53e256m32d1ks.dts |   16 +
 ...k3-am67a-r5-kontron-sa67-mt53e2g32d4de.dts |   17 +
 arch/arm/dts/k3-am67a-r5-kontron-sa67.dtsi    |  104 +
 arch/arm/mach-k3/j722s/Kconfig                |   18 +
 board/kontron/sa67/Kconfig                    |   21 +
 board/kontron/sa67/MAINTAINERS                |    7 +
 board/kontron/sa67/Makefile                   |    5 +
 board/kontron/sa67/board-cfg.yaml             |   36 +
 board/kontron/sa67/common.c                   |   41 +
 board/kontron/sa67/pm-cfg.yaml                |   12 +
 board/kontron/sa67/r5.c                       |  144 +
 board/kontron/sa67/rm-cfg.yaml                | 1137 +++++++
 board/kontron/sa67/sa67.c                     |  311 ++
 board/kontron/sa67/sa67.env                   |   21 +
 board/kontron/sa67/sec-cfg.yaml               |  379 +++
 board/kontron/sa67/tifs-rm-cfg.yaml           |  993 ++++++
 configs/kontron_sa67_a53_defconfig            |  211 ++
 configs/kontron_sa67_r5_defconfig             |  126 +
 doc/board/kontron/index.rst                   |    1 +
 doc/board/kontron/sa67.rst                    |   62 +
 doc/board/ti/k3.rst                           |    1 +
 include/configs/kontron_sa67.h                |   13 +
 26 files changed, 9599 insertions(+)
 create mode 100644 arch/arm/dts/k3-am67a-kontron-sa67-base-u-boot.dtsi
 create mode 100644 arch/arm/dts/k3-am67a-kontron-sa67-binman.dtsi
 create mode 100644 arch/arm/dts/k3-am67a-kontron-sa67-ddr-mt53e256m32d1ks.dtsi
 create mode 100644 arch/arm/dts/k3-am67a-kontron-sa67-ddr-mt53e2g32d4de.dtsi
 create mode 100644 arch/arm/dts/k3-am67a-r5-kontron-sa67-mt53e256m32d1ks.dts
 create mode 100644 arch/arm/dts/k3-am67a-r5-kontron-sa67-mt53e2g32d4de.dts
 create mode 100644 arch/arm/dts/k3-am67a-r5-kontron-sa67.dtsi
 create mode 100644 board/kontron/sa67/Kconfig
 create mode 100644 board/kontron/sa67/MAINTAINERS
 create mode 100644 board/kontron/sa67/Makefile
 create mode 100644 board/kontron/sa67/board-cfg.yaml
 create mode 100644 board/kontron/sa67/common.c
 create mode 100644 board/kontron/sa67/pm-cfg.yaml
 create mode 100644 board/kontron/sa67/r5.c
 create mode 100644 board/kontron/sa67/rm-cfg.yaml
 create mode 100644 board/kontron/sa67/sa67.c
 create mode 100644 board/kontron/sa67/sa67.env
 create mode 100644 board/kontron/sa67/sec-cfg.yaml
 create mode 100644 board/kontron/sa67/tifs-rm-cfg.yaml
 create mode 100644 configs/kontron_sa67_a53_defconfig
 create mode 100644 configs/kontron_sa67_r5_defconfig
 create mode 100644 doc/board/kontron/sa67.rst
 create mode 100644 include/configs/kontron_sa67.h
arch/arm/dts/k3-am67a-kontron-sa67-base-u-boot.dtsi new file +127 -0
new file mode 100644
index 00000000000..68436949479
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2025 Kontron Europe GmbH
+ */
+
+#include "k3-am67a-kontron-sa67-binman.dtsi"
+
+/ {
+	board {
+		compatible = "kontron,sysinfo-sa67";
+
+		pinctrl-names = "pull-up", "pull-down";
+		pinctrl-0 = <&board_sysinfo_pull_up>;
+		pinctrl-1 = <&board_sysinfo_pull_down>;
+
+		boardcfg-gpios = <&main_gpio0 15 GPIO_ACTIVE_HIGH>,
+				 <&main_gpio0 16 GPIO_ACTIVE_HIGH>,
+				 <&main_gpio0 17 GPIO_ACTIVE_HIGH>,
+				 <&main_gpio0 18 GPIO_ACTIVE_HIGH>,
+				 <&main_gpio0 19 GPIO_ACTIVE_HIGH>;
+		revision-gpios = <&main_gpio0 21 GPIO_ACTIVE_HIGH>,
+				 <&main_gpio0 22 GPIO_ACTIVE_HIGH>;
+		bootph-all;
+	};
+
+	chosen {
+		tick-timer = &main_timer0;
+	};
+};
+
+/* can be removed when upstream soc dtsi is updated */
+&cbass_main {
+	main_i2c4: i2c@fe80000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x0fe80000 0x00 0x100>;
+		interrupts-extended = <&main_gpio_intr 178>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 257 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 257 2>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+};
+
+&crypto {
+	rng: rng@40910000 {
+		compatible = "inside-secure,safexcel-eip76";
+		reg = <0x00 0x40910000 0x0 0x7d>;
+		interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&main_gpio0 {
+	reset-out-hog {
+		pinctrl-names = "default";
+		pinctrl-0 = <&reset_out_hog_pins_default>;
+		gpio-hog;
+		output-low;
+		gpios = <9 GPIO_ACTIVE_LOW>;
+		line-name = "RESET_OUT#";
+	};
+};
+
+&dmsc {
+	bootph-pre-ram;
+};
+
+&main_bcdma {
+	bootph-pre-ram;
+};
+
+/* can be removed when upstream soc dtsi is updated */
+&main_conf {
+	audio_refclk0: clock@82e0 {
+		compatible = "ti,am62-audio-refclk";
+		reg = <0x82e0 0x4>;
+		clocks = <&k3_clks 157 0>;
+		assigned-clocks = <&k3_clks 157 0>;
+		assigned-clock-parents = <&k3_clks 157 15>;
+		#clock-cells = <0>;
+	};
+};
+
+/* can be removed when upstream soc dtsi is updated */
+&main_pmx0 {
+	/delete-property/ pinctrl-single,gpio-range;
+	/delete-node/ gpio-range;
+};
+
+&main_pmx0 {
+	bootph-all;
+
+	board_sysinfo_pull_up: board-sysinfo-pull-up-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x03c, PIN_INPUT_PULLUP, 7)		/* (R22) GPNC9_AD0.GPIO0_15 */
+			J722S_IOPAD(0x040, PIN_INPUT_PULLUP, 7)		/* (R23) GPNC9_AD1.GPIO0_16 */
+			J722S_IOPAD(0x044, PIN_INPUT_PULLUP, 7)		/* (R26) GPNC9_AD2.GPIO0_17 */
+			J722S_IOPAD(0x048, PIN_INPUT_PULLUP, 7)		/* (T27) GPNC9_AD3.GPIO0_18 */
+			J722S_IOPAD(0x04c, PIN_INPUT_PULLUP, 7)		/* (T25) GPNC9_AD4.GPIO0_19 */
+			J722S_IOPAD(0x050, PIN_INPUT_PULLUP, 7)		/* (T24) GPNC9_AD5.GPIO0_20 */
+			J722S_IOPAD(0x054, PIN_INPUT_PULLUP, 7)		/* (T21) GPNC9_AD6.GPIO0_21 */
+			J722S_IOPAD(0x058, PIN_INPUT_PULLUP, 7)		/* (T22) GPNC9_AD7.GPIO0_22 */
+		>;
+		bootph-all;
+	};
+
+	board_sysinfo_pull_down: board-sysinfo-pull-down-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x03c, PIN_INPUT_PULLDOWN, 7)	/* (R22) GPNC9_AD0.GPIO0_15 */
+			J722S_IOPAD(0x040, PIN_INPUT_PULLDOWN, 7)	/* (R23) GPNC9_AD1.GPIO0_16 */
+			J722S_IOPAD(0x044, PIN_INPUT_PULLDOWN, 7)	/* (R26) GPNC9_AD2.GPIO0_17 */
+			J722S_IOPAD(0x048, PIN_INPUT_PULLDOWN, 7)	/* (T27) GPNC9_AD3.GPIO0_18 */
+			J722S_IOPAD(0x04c, PIN_INPUT_PULLDOWN, 7)	/* (T25) GPNC9_AD4.GPIO0_19 */
+			J722S_IOPAD(0x050, PIN_INPUT_PULLDOWN, 7)	/* (T24) GPNC9_AD5.GPIO0_20 */
+			J722S_IOPAD(0x054, PIN_INPUT_PULLDOWN, 7)	/* (T21) GPNC9_AD6.GPIO0_21 */
+			J722S_IOPAD(0x058, PIN_INPUT_PULLDOWN, 7)	/* (T22) GPNC9_AD7.GPIO0_22 */
+		>;
+		bootph-all;
+	};
+
+	reset_out_hog_pins_default: reset-out-hog-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x024, PIN_OUTPUT, 7)	/* (N27) GPIO0_9 */
+		>;
+	};
+};
arch/arm/dts/k3-am67a-kontron-sa67-binman.dtsi new file +202 -0

202 lines not on this page · raw message

arch/arm/dts/k3-am67a-kontron-sa67-ddr-mt53e256m32d1ks.dtsi new file +2797 -0

2,671 lines not on this page · raw message

arch/arm/dts/k3-am67a-kontron-sa67-ddr-mt53e2g32d4de.dtsi new file +2797 -0

2,797 lines not on this page · raw message

arch/arm/dts/k3-am67a-r5-kontron-sa67-mt53e256m32d1ks.dts new file +16 -0
new file mode 100644
index 00000000000..f08a13aa95b

Lines of this file are not shown. View the raw message.

arch/arm/dts/k3-am67a-r5-kontron-sa67-mt53e2g32d4de.dts new file +17 -0
new file mode 100644
index 00000000000..760d4843609

Lines of this file are not shown. View the raw message.

arch/arm/dts/k3-am67a-r5-kontron-sa67.dtsi new file +104 -0

104 lines not on this page · raw message

arch/arm/mach-k3/j722s/Kconfig +18 -0
index fe76d77e58a..c0c4ec8e0ac 100644

Lines of this file are not shown. View the raw message.

board/kontron/sa67/Kconfig new file +21 -0
new file mode 100644
index 00000000000..1c004d3b0ce

Lines of this file are not shown. View the raw message.

board/kontron/sa67/MAINTAINERS new file +7 -0
new file mode 100644
index 00000000000..cbc6fd07721

Lines of this file are not shown. View the raw message.

board/kontron/sa67/Makefile new file +5 -0
new file mode 100644
index 00000000000..767f17054d9

Lines of this file are not shown. View the raw message.

board/kontron/sa67/board-cfg.yaml new file +36 -0
new file mode 100644
index 00000000000..7993b894a73

Lines of this file are not shown. View the raw message.

board/kontron/sa67/common.c new file +41 -0

41 lines not on this page · raw message

board/kontron/sa67/pm-cfg.yaml new file +12 -0
new file mode 100644
index 00000000000..355dcd9788b

Lines of this file are not shown. View the raw message.

board/kontron/sa67/r5.c new file +144 -0

144 lines not on this page · raw message

board/kontron/sa67/rm-cfg.yaml new file +1137 -0

1,137 lines not on this page · raw message

board/kontron/sa67/sa67.c new file +311 -0

311 lines not on this page · raw message

board/kontron/sa67/sa67.env new file +21 -0
new file mode 100644
index 00000000000..a02e0e37be8

Lines of this file are not shown. View the raw message.

board/kontron/sa67/sec-cfg.yaml new file +379 -0

379 lines not on this page · raw message

board/kontron/sa67/tifs-rm-cfg.yaml new file +993 -0

993 lines not on this page · raw message

configs/kontron_sa67_a53_defconfig new file +211 -0

211 lines not on this page · raw message

configs/kontron_sa67_r5_defconfig new file +126 -0

126 lines not on this page · raw message

doc/board/kontron/index.rst +1 -0
index bd205ec628e..6f84b4518ef 100644

Lines of this file are not shown. View the raw message.

doc/board/kontron/sa67.rst new file +62 -0

62 lines not on this page · raw message

doc/board/ti/k3.rst +1 -0
index ed04a57c167..604e1ce4d55 100644

Lines of this file are not shown. View the raw message.

include/configs/kontron_sa67.h new file +13 -0
new file mode 100644
index 00000000000..ad96de9fee3

Lines of this file are not shown. View the raw message.

The rest of this diff is not shown. View the raw message.

Signature · 1 line
2.47.3

Part of the diff is not shown here. View the raw message.

#5 lore raw
In reply to Michael Walle
Quoted 10 lines · Michael Walle

Add initial support for the SMARC-sAM67 board (enineering name sa67).

The board has different RAM options. The exact configuration is tri-state encoded with strapping options. u-boot already has support for that, but unfortunately, the pull-ups/-downs can only be configured by the pinmux and not by the gpio controller. Therefore, this will introduce another method to read the tri-state encoded strappings by switching the pinmux configurations on the fly.

Quoted 5 lines

There is also a sysinfo driver to read the remaining board options and is used to apply corresponding device tree overlays.

The device tree itself is picked from the last tag of the dt-rebasing tree.

Please disregard this patchset. I was just informed that this product is discontinued (without ever being released to the market).

-michael