Skip to contentSkip to conversation

net: hsr: sync hw addr of slave2 according to slave1 hw addr on PRP

PATCH Applied Fernando Fernandez Mancera 5 participants 9 messages Apr 9, 2025 – Mar 30

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 net: hsr: sync hw addr of slave2 according to slave1 hw addr on PRP

In order to work properly PRP requires slave1 and slave2 to share the same MAC address. To ease the configuration process on userspace tools, sync the slave2 MAC address with slave1. In addition, when deleting the port from the list, restore the original MAC address.

---
v3: restore the original MAC address on slave removal.

---
 net/hsr/hsr_device.c | 5 +++++
 net/hsr/hsr_main.c   | 9 +++++++++
 net/hsr/hsr_main.h   | 1 +
 net/hsr/hsr_slave.c  | 2 ++
 4 files changed, 17 insertions(+)
net/hsr/hsr_device.c +5 -0
index 439cfb7ad5d1..e8922e8d9398 100644
@@ -761,6 +761,11 @@ int hsr_dev_finalize(struct net_device *hsr_dev, struct net_device *slave[2],
 	if (res)
 		goto err_unregister;
 
+	if (protocol_version == PRP_V1) {
+		eth_hw_addr_set(slave[1], slave[0]->dev_addr);
+		call_netdevice_notifiers(NETDEV_CHANGEADDR, slave[1]);
+	}
+
 	if (interlink) {
 		res = hsr_add_port(hsr, interlink, HSR_PT_INTERLINK, extack);
 		if (res)
net/hsr/hsr_main.c +9 -0
index d7ae32473c41..192893c3f2ec 100644
@@ -78,6 +78,15 @@ static int hsr_netdev_notify(struct notifier_block *nb, unsigned long event,
 			eth_hw_addr_set(master->dev, dev->dev_addr);
 			call_netdevice_notifiers(NETDEV_CHANGEADDR,
 						 master->dev);
+
+			if (hsr->prot_version == PRP_V1) {
+				port = hsr_port_get_hsr(hsr, HSR_PT_SLAVE_B);
+				if (port) {
+					eth_hw_addr_set(port->dev, dev->dev_addr);
+					call_netdevice_notifiers(NETDEV_CHANGEADDR,
+								 port->dev);
+				}
+			}
 		}
 
 		/* Make sure we recognize frames from ourselves in hsr_rcv() */
net/hsr/hsr_main.h +1 -0
index 1bc47b17a296..135ec5fce019 100644
@@ -155,6 +155,7 @@ struct hsr_port {
 	struct hsr_priv		*hsr;
 	enum hsr_port_type	type;
 	struct rcu_head		rcu;
+	unsigned char		original_macaddress[ETH_ALEN];
 };
 
 struct hsr_frame_info;
net/hsr/hsr_slave.c +2 -0
index 2a802a5de2ac..b87b6a6fe070 100644
@@ -196,6 +196,7 @@ int hsr_add_port(struct hsr_priv *hsr, struct net_device *dev,
 	port->hsr = hsr;
 	port->dev = dev;
 	port->type = type;
+	ether_addr_copy(port->original_macaddress, dev->dev_addr);
 
 	if (type != HSR_PT_MASTER) {
 		res = hsr_portdev_setup(hsr, dev, port, extack);
@@ -232,6 +233,7 @@ void hsr_del_port(struct hsr_port *port)
 		if (!port->hsr->fwd_offloaded)
 			dev_set_promiscuity(port->dev, -1);
 		netdev_upper_dev_unlink(port->dev, master->dev);
+		eth_hw_addr_set(port->dev, port->original_macaddress);
 	}
 
 	kfree_rcu(port, rcu);
Signature · 1 line
2.49.0
#1 lore raw
This patch was applied to netdev/net-next.git (main) by David S. Miller <[email protected]>:

Hello:

This patch was applied to netdev/net-next.git (main) by David S. Miller <[email protected]>:

Quoted 8 lines · On Wed, 9 Apr 2025 12:19:11 +0200 you wrote:

In order to work properly PRP requires slave1 and slave2 to share the same MAC address. To ease the configuration process on userspace tools, sync the slave2 MAC address with slave1. In addition, when deleting the port from the list, restore the original MAC address.

[...]

Here is the summary with links:
- [v3,net-next] net: hsr: sync hw addr of slave2 according to slave1 hw addr on PRP

    https://git.kernel.org/netdev/net-next/c/b65999e7238e

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html
#2 lore raw
In reply to Fernando Fernandez Mancera
Quoted 76 lines · Fernando Fernandez Mancera

In order to work properly PRP requires slave1 and slave2 to share the same MAC address. To ease the configuration process on userspace tools, sync the slave2 MAC address with slave1. In addition, when deleting the port from the list, restore the original MAC address.

---
v3: restore the original MAC address on slave removal.

---
 net/hsr/hsr_device.c | 5 +++++
 net/hsr/hsr_main.c   | 9 +++++++++
 net/hsr/hsr_main.h   | 1 +
 net/hsr/hsr_slave.c  | 2 ++
 4 files changed, 17 insertions(+)
net/hsr/hsr_device.c +5 -0
index 439cfb7ad5d1..e8922e8d9398 100644
@@ -761,6 +761,11 @@ int hsr_dev_finalize(struct net_device *hsr_dev, struct net_device *slave[2],
 	if (res)
 		goto err_unregister;
 
+	if (protocol_version == PRP_V1) {
+		eth_hw_addr_set(slave[1], slave[0]->dev_addr);
+		call_netdevice_notifiers(NETDEV_CHANGEADDR, slave[1]);
+	}
+
 	if (interlink) {
 		res = hsr_add_port(hsr, interlink, HSR_PT_INTERLINK, extack);
 		if (res)
net/hsr/hsr_main.c +9 -0
index d7ae32473c41..192893c3f2ec 100644
@@ -78,6 +78,15 @@ static int hsr_netdev_notify(struct notifier_block *nb, unsigned long event,
 			eth_hw_addr_set(master->dev, dev->dev_addr);
 			call_netdevice_notifiers(NETDEV_CHANGEADDR,
 						 master->dev);
+
+			if (hsr->prot_version == PRP_V1) {
+				port = hsr_port_get_hsr(hsr, HSR_PT_SLAVE_B);
+				if (port) {
+					eth_hw_addr_set(port->dev, dev->dev_addr);
+					call_netdevice_notifiers(NETDEV_CHANGEADDR,
+								 port->dev);
+				}
+			}
 		}
 
 		/* Make sure we recognize frames from ourselves in hsr_rcv() */
net/hsr/hsr_main.h +1 -0
index 1bc47b17a296..135ec5fce019 100644
@@ -155,6 +155,7 @@ struct hsr_port {
 	struct hsr_priv		*hsr;
 	enum hsr_port_type	type;
 	struct rcu_head		rcu;
+	unsigned char		original_macaddress[ETH_ALEN];
 };
 
 struct hsr_frame_info;
net/hsr/hsr_slave.c +1 -0
index 2a802a5de2ac..b87b6a6fe070 100644
@@ -196,6 +196,7 @@ int hsr_add_port(struct hsr_priv *hsr, struct net_device *dev,
 	port->hsr = hsr;
 	port->dev = dev;
 	port->type = type;
+	ether_addr_copy(port->original_macaddress, dev->dev_addr);
 
 	if (type != HSR_PT_MASTER) {
 		res = hsr_portdev_setup(hsr, dev, port, extack);

net/hsr/hsr_slave.c void hsr_del_port(struct hsr_port *port) · line 239

Quoted 7 lines
net/hsr/hsr_slave.c +1 -0
@@ -232,6 +233,7 @@ void hsr_del_port(struct hsr_port *port)
 		if (!port->hsr->fwd_offloaded)
 			dev_set_promiscuity(port->dev, -1);
 		netdev_upper_dev_unlink(port->dev, master->dev);
+		eth_hw_addr_set(port->dev, port->original_macaddress);
 	}
 
 	kfree_rcu(port, rcu);

Hi Fernando,

Thanks for the patch. The logic to sync the slave2 MAC address with slave1 for PRP is sound, but there are a few implementation issues here that will cause hardware filtering problems and style violations.

1. Hardware MAC Filtering
In your current implementation:

  if (protocol_version == PRP_V1) {
      eth_hw_addr_set(slave[1], slave[0]->dev_addr);

      call_netdevice_notifiers(NETDEV_CHANGEADDR, slave[1]);
  }

eth_hw_addr_set() is appropriate for virtual devices (like the hsr_dev itself), but slave[1] is a physical net_device. By using this helper, you are bypassing dev->netdev_ops->ndo_set_mac_address. This means the physical NIC's hardware MAC filter will not be programmed, and it will silently drop unicast traffic destined for the new PRP MAC address unless the interface happens to be in promiscuous mode. You should use dev_set_mac_address() here instead. Note that unlike eth_hw_addr_set(), dev_set_mac_address() can fail and returns an error code, so you will need to check its return value and handle the error path accordingly.

2. Teardown Notifiers
In hsr_del_port():

  netdev_upper_dev_unlink(port->dev, master->dev);
  eth_hw_addr_set(port->dev, port->original_macaddress);

You have the same issue with eth_hw_addr_set() here. Additionally, unlike the setup paths, this version omits call_netdevice_notifiers (NETDEV_CHANGEADDR, port->dev). Switching to dev_set_mac_address() for the restoration will handle both the hardware programming and the notifier chain automatically.

3. Coding Style
In hsr_main.h:

  unsigned char original_macaddress[ETH_ALEN];

Please use u8 instead of unsigned char for byte arrays to align with standard netdev coding styles.

Please address these points and submit a v4.

Best regards,
Luka Gejak

#3 lore raw
Quoted 115 lines · Luka Gejak
Quoted 76 lines · Fernando Fernandez Mancera

In order to work properly PRP requires slave1 and slave2 to share the same MAC address. To ease the configuration process on userspace tools, sync the slave2 MAC address with slave1. In addition, when deleting the port from the list, restore the original MAC address.

---
v3: restore the original MAC address on slave removal.

---
  net/hsr/hsr_device.c | 5 +++++
  net/hsr/hsr_main.c   | 9 +++++++++
  net/hsr/hsr_main.h   | 1 +
  net/hsr/hsr_slave.c  | 2 ++
  4 files changed, 17 insertions(+)
net/hsr/hsr_device.c +5 -0
index 439cfb7ad5d1..e8922e8d9398 100644
@@ -761,6 +761,11 @@ int hsr_dev_finalize(struct net_device *hsr_dev, struct net_device *slave[2],
  	if (res)
  		goto err_unregister;
 
+	if (protocol_version == PRP_V1) {
+		eth_hw_addr_set(slave[1], slave[0]->dev_addr);
+		call_netdevice_notifiers(NETDEV_CHANGEADDR, slave[1]);
+	}
+
  	if (interlink) {
  		res = hsr_add_port(hsr, interlink, HSR_PT_INTERLINK, extack);
  		if (res)
net/hsr/hsr_main.c +9 -0
index d7ae32473c41..192893c3f2ec 100644
@@ -78,6 +78,15 @@ static int hsr_netdev_notify(struct notifier_block *nb, unsigned long event,
  			eth_hw_addr_set(master->dev, dev->dev_addr);
  			call_netdevice_notifiers(NETDEV_CHANGEADDR,
  						 master->dev);
+
+			if (hsr->prot_version == PRP_V1) {
+				port = hsr_port_get_hsr(hsr, HSR_PT_SLAVE_B);
+				if (port) {
+					eth_hw_addr_set(port->dev, dev->dev_addr);
+					call_netdevice_notifiers(NETDEV_CHANGEADDR,
+								 port->dev);
+				}
+			}
  		}
 
  		/* Make sure we recognize frames from ourselves in hsr_rcv() */
net/hsr/hsr_main.h +1 -0
index 1bc47b17a296..135ec5fce019 100644
@@ -155,6 +155,7 @@ struct hsr_port {
  	struct hsr_priv		*hsr;
  	enum hsr_port_type	type;
  	struct rcu_head		rcu;
+	unsigned char		original_macaddress[ETH_ALEN];
  };
 
  struct hsr_frame_info;
net/hsr/hsr_slave.c +1 -0
index 2a802a5de2ac..b87b6a6fe070 100644
@@ -196,6 +196,7 @@ int hsr_add_port(struct hsr_priv *hsr, struct net_device *dev,
  	port->hsr = hsr;
  	port->dev = dev;
  	port->type = type;
+	ether_addr_copy(port->original_macaddress, dev->dev_addr);
 
  	if (type != HSR_PT_MASTER) {
  		res = hsr_portdev_setup(hsr, dev, port, extack);

net/hsr/hsr_slave.c void hsr_del_port(struct hsr_port *port) · line 239

Quoted 7 lines
net/hsr/hsr_slave.c +1 -0
@@ -232,6 +233,7 @@ void hsr_del_port(struct hsr_port *port)
  		if (!port->hsr->fwd_offloaded)
  			dev_set_promiscuity(port->dev, -1);
  		netdev_upper_dev_unlink(port->dev, master->dev);
+		eth_hw_addr_set(port->dev, port->original_macaddress);
  	}
 
  	kfree_rcu(port, rcu);

Hi Fernando,

Thanks for the patch. The logic to sync the slave2 MAC address with slave1 for PRP is sound, but there are a few implementation issues here that will cause hardware filtering problems and style violations.

1. Hardware MAC Filtering
In your current implementation:

   if (protocol_version == PRP_V1) {
       eth_hw_addr_set(slave[1], slave[0]->dev_addr);

       call_netdevice_notifiers(NETDEV_CHANGEADDR, slave[1]);
   }

eth_hw_addr_set() is appropriate for virtual devices (like the hsr_dev itself), but slave[1] is a physical net_device. By using this helper, you are bypassing dev->netdev_ops->ndo_set_mac_address. This means the physical NIC's hardware MAC filter will not be programmed, and it will silently drop unicast traffic destined for the new PRP MAC address unless the interface happens to be in promiscuous mode. You should use dev_set_mac_address() here instead. Note that unlike eth_hw_addr_set(), dev_set_mac_address() can fail and returns an error code, so you will need to check its return value and handle the error path accordingly.

2. Teardown Notifiers
In hsr_del_port():

Quoted 9 lines
   netdev_upper_dev_unlink(port->dev, master->dev);
   eth_hw_addr_set(port->dev, port->original_macaddress);

You have the same issue with eth_hw_addr_set() here. Additionally, unlike the setup paths, this version omits call_netdevice_notifiers (NETDEV_CHANGEADDR, port->dev). Switching to dev_set_mac_address() for the restoration will handle both the hardware programming and the notifier chain automatically.

These points makes sense. I guess I didn't notice the that eth_hw_addr_set() due to my interface being set to promiscuous mode at hsr_slave.c.

Let me research a bit more about the impact here and will get back to you either with a new patch or an reply here.

Quoted 8 lines

3. Coding Style
In hsr_main.h:

   unsigned char original_macaddress[ETH_ALEN];

Please use u8 instead of unsigned char for byte arrays to align with standard netdev coding styles.

I used unsigned char because it was already used around HSR code already, so I chose consistency. If there is a preference for u8 over unsigned char I could change it.

Quoted 2 lines

Please address these points and submit a v4.

Well, this is almost a year old so I am sending a fix instead. Is this some kind of automated bot going through all the patches in netdev mailing list? I am a bit confused about receiving a patch review a year later.

Quoted 3 lines

Best regards,
Luka Gejak

#4 lore raw
Quoted 134 lines · Fernando Fernandez Mancera
Quoted 110 lines · Luka Gejak
Quoted 72 lines · Fernando Fernandez Mancera

In order to work properly PRP requires slave1 and slave2 to share the same MAC address. To ease the configuration process on userspace tools, sync the slave2 MAC address with slave1. In addition, when deleting the port from the list, restore the original MAC address.

---
v3: restore the original MAC address on slave removal.

---
  net/hsr/hsr_device.c | 5 +++++
  net/hsr/hsr_main.c   | 9 +++++++++
  net/hsr/hsr_main.h   | 1 +
  net/hsr/hsr_slave.c  | 2 ++
  4 files changed, 17 insertions(+)
net/hsr/hsr_device.c +4 -0
index 439cfb7ad5d1..e8922e8d9398 100644
@@ -761,6 +761,11 @@ int hsr_dev_finalize(struct net_device *hsr_dev, struct net_device *slave[2],
  	if (res)
  		goto err_unregister;
  +	if (protocol_version == PRP_V1) {
+		eth_hw_addr_set(slave[1], slave[0]->dev_addr);
+		call_netdevice_notifiers(NETDEV_CHANGEADDR, slave[1]);
+	}
+
  	if (interlink) {
  		res = hsr_add_port(hsr, interlink, HSR_PT_INTERLINK, extack);
  		if (res)
net/hsr/hsr_main.c +9 -0
index d7ae32473c41..192893c3f2ec 100644
@@ -78,6 +78,15 @@ static int hsr_netdev_notify(struct notifier_block *nb, unsigned long event,
  			eth_hw_addr_set(master->dev, dev->dev_addr);
  			call_netdevice_notifiers(NETDEV_CHANGEADDR,
  						 master->dev);
+
+			if (hsr->prot_version == PRP_V1) {
+				port = hsr_port_get_hsr(hsr, HSR_PT_SLAVE_B);
+				if (port) {
+					eth_hw_addr_set(port->dev, dev->dev_addr);
+					call_netdevice_notifiers(NETDEV_CHANGEADDR,
+								 port->dev);
+				}
+			}
  		}
    		/* Make sure we recognize frames from ourselves in hsr_rcv() */
net/hsr/hsr_main.h +1 -0
index 1bc47b17a296..135ec5fce019 100644
@@ -155,6 +155,7 @@ struct hsr_port {
  	struct hsr_priv		*hsr;
  	enum hsr_port_type	type;
  	struct rcu_head		rcu;
+	unsigned char		original_macaddress[ETH_ALEN];
  };
    struct hsr_frame_info;
net/hsr/hsr_slave.c +1 -0
index 2a802a5de2ac..b87b6a6fe070 100644
@@ -196,6 +196,7 @@ int hsr_add_port(struct hsr_priv *hsr, struct net_device *dev,
  	port->hsr = hsr;
  	port->dev = dev;
  	port->type = type;
+	ether_addr_copy(port->original_macaddress, dev->dev_addr);
    	if (type != HSR_PT_MASTER) {
  		res = hsr_portdev_setup(hsr, dev, port, extack);

net/hsr/hsr_slave.c void hsr_del_port(struct hsr_port *port) · line 238

Quoted 6 lines
net/hsr/hsr_slave.c +1 -0
@@ -232,6 +233,7 @@ void hsr_del_port(struct hsr_port *port)
  		if (!port->hsr->fwd_offloaded)
  			dev_set_promiscuity(port->dev, -1);
  		netdev_upper_dev_unlink(port->dev, master->dev);
+		eth_hw_addr_set(port->dev, port->original_macaddress);
  	}
    	kfree_rcu(port, rcu);

Hi Fernando,

Thanks for the patch. The logic to sync the slave2 MAC address with slave1 for PRP is sound, but there are a few implementation issues here that will cause hardware filtering problems and style violations.

1. Hardware MAC Filtering
In your current implementation:

   if (protocol_version == PRP_V1) {
       eth_hw_addr_set(slave[1], slave[0]->dev_addr);

       call_netdevice_notifiers(NETDEV_CHANGEADDR, slave[1]);
   }

eth_hw_addr_set() is appropriate for virtual devices (like the hsr_dev itself), but slave[1] is a physical net_device. By using this helper, you are bypassing dev->netdev_ops->ndo_set_mac_address. This means the physical NIC's hardware MAC filter will not be programmed, and it will silently drop unicast traffic destined for the new PRP MAC address unless the interface happens to be in promiscuous mode. You should use dev_set_mac_address() here instead. Note that unlike eth_hw_addr_set(), dev_set_mac_address() can fail and returns an error code, so you will need to check its return value and handle the error path accordingly.

2. Teardown Notifiers
In hsr_del_port():

Quoted 9 lines
   netdev_upper_dev_unlink(port->dev, master->dev);
   eth_hw_addr_set(port->dev, port->original_macaddress);

You have the same issue with eth_hw_addr_set() here. Additionally, unlike the setup paths, this version omits call_netdevice_notifiers (NETDEV_CHANGEADDR, port->dev). Switching to dev_set_mac_address() for the restoration will handle both the hardware programming and the notifier chain automatically.

These points makes sense. I guess I didn't notice the that eth_hw_addr_set() due to my interface being set to promiscuous mode at hsr_slave.c.

Let me research a bit more about the impact here and will get back to you either with a new patch or an reply here.

Quoted 8 lines

3. Coding Style
In hsr_main.h:

   unsigned char original_macaddress[ETH_ALEN];

Please use u8 instead of unsigned char for byte arrays to align with standard netdev coding styles.

Quoted 11 lines

I used unsigned char because it was already used around HSR code already, so I chose consistency. If there is a preference for u8 over unsigned char I could change it.

Quoted 2 lines

Please address these points and submit a v4.

Well, this is almost a year old so I am sending a fix instead. Is this some kind of automated bot going through all the patches in netdev mailing list? I am a bit confused about receiving a patch review a year later.

Quoted 3 lines

Best regards,
Luka Gejak

Hi Fernando,
I was setting up lei for the mailing list and because I didn't set it up correctly, patches that were filtered and downloaded by lei were older and I noticed it only later after carefully checking why patch count was low.
Best regards,
Luka Gejak

#5 lore raw
In reply to Fernando Fernandez Mancera
Quoted 124 lines · Fernando Fernandez Mancera
Quoted 113 lines · Luka Gejak
Quoted 75 lines · Fernando Fernandez Mancera

In order to work properly PRP requires slave1 and slave2 to share the same MAC address. To ease the configuration process on userspace tools, sync the slave2 MAC address with slave1. In addition, when deleting the port from the list, restore the original MAC address.

---
v3: restore the original MAC address on slave removal.
---
  net/hsr/hsr_device.c | 5 +++++ net/hsr/hsr_main.c   | 9 +++++++++ net/hsr/hsr_main.h   | 1 + net/hsr/hsr_slave.c  | 2 ++

  4 files changed, 17 insertions(+)
net/hsr/hsr_device.c +5 -0
index 439cfb7ad5d1..e8922e8d9398 100644
@@ -761,6 +761,11 @@ int hsr_dev_finalize(struct net_device *hsr_dev, 
 struct net_device *slave[2],
       if (res)
           goto err_unregister;
+    if (protocol_version == PRP_V1) {
+        eth_hw_addr_set(slave[1], slave[0]->dev_addr);
+        call_netdevice_notifiers(NETDEV_CHANGEADDR, slave[1]);
+    }
+
       if (interlink) {
           res = hsr_add_port(hsr, interlink, HSR_PT_INTERLINK, extack);
           if (res)
net/hsr/hsr_main.c +9 -0
index d7ae32473c41..192893c3f2ec 100644
@@ -78,6 +78,15 @@ static int hsr_netdev_notify(struct notifier_block 
 *nb, unsigned long event,
               eth_hw_addr_set(master->dev, dev->dev_addr);
               call_netdevice_notifiers(NETDEV_CHANGEADDR,
                            master->dev);
+
+            if (hsr->prot_version == PRP_V1) {
+                port = hsr_port_get_hsr(hsr, HSR_PT_SLAVE_B);
+                if (port) {
+                    eth_hw_addr_set(port->dev, dev->dev_addr);
+                    call_netdevice_notifiers(NETDEV_CHANGEADDR,
+                                 port->dev);
+                }
+            }
           }
           /* Make sure we recognize frames from ourselves in hsr_rcv() */
net/hsr/hsr_main.h +1 -0
index 1bc47b17a296..135ec5fce019 100644
@@ -155,6 +155,7 @@ struct hsr_port {
       struct hsr_priv        *hsr;
       enum hsr_port_type    type;
       struct rcu_head        rcu;
+    unsigned char        original_macaddress[ETH_ALEN];
   };
   struct hsr_frame_info;
net/hsr/hsr_slave.c +1 -0
index 2a802a5de2ac..b87b6a6fe070 100644
@@ -196,6 +196,7 @@ int hsr_add_port(struct hsr_priv *hsr, struct 
 net_device *dev,
       port->hsr = hsr;
       port->dev = dev;
       port->type = type;
+    ether_addr_copy(port->original_macaddress, dev->dev_addr);
       if (type != HSR_PT_MASTER) {
           res = hsr_portdev_setup(hsr, dev, port, extack);

net/hsr/hsr_slave.c void hsr_del_port(struct hsr_port *port) · line 238

Quoted 6 lines
net/hsr/hsr_slave.c +1 -0
@@ -232,6 +233,7 @@ void hsr_del_port(struct hsr_port *port)
           if (!port->hsr->fwd_offloaded)
               dev_set_promiscuity(port->dev, -1);
           netdev_upper_dev_unlink(port->dev, master->dev);
+        eth_hw_addr_set(port->dev, port->original_macaddress);
       }
       kfree_rcu(port, rcu);

Hi Fernando,

Thanks for the patch. The logic to sync the slave2 MAC address with slave1 for PRP is sound, but there are a few implementation issues here that will cause hardware filtering problems and style violations.

1. Hardware MAC Filtering
In your current implementation:

   if (protocol_version == PRP_V1) {

       eth_hw_addr_set(slave[1], slave[0]->dev_addr);

       call_netdevice_notifiers(NETDEV_CHANGEADDR, slave[1]);

   }

eth_hw_addr_set() is appropriate for virtual devices (like the hsr_dev itself), but slave[1] is a physical net_device. By using this helper, you are bypassing dev->netdev_ops->ndo_set_mac_address. This means the physical NIC's hardware MAC filter will not be programmed, and it will silently drop unicast traffic destined for the new PRP MAC address unless the interface happens to be in promiscuous mode. You should use dev_set_mac_address() here instead. Note that unlike eth_hw_addr_set(), dev_set_mac_address() can fail and returns an error code, so you will need to check its return value and handle the error path accordingly.

2. Teardown Notifiers
In hsr_del_port():

Quoted 9 lines

   netdev_upper_dev_unlink(port->dev, master->dev); eth_hw_addr_set(port->dev, port->original_macaddress);

You have the same issue with eth_hw_addr_set() here. Additionally, unlike the setup paths, this version omits call_netdevice_notifiers (NETDEV_CHANGEADDR, port->dev). Switching to dev_set_mac_address() for the restoration will handle both the hardware programming and the notifier chain automatically.

Quoted 4 lines

These points makes sense. I guess I didn't notice the that eth_hw_addr_set() due to my interface being set to promiscuous mode at hsr_slave.c.

Let me research a bit more about the impact here and will get back to you either with a new patch or an reply here.

Does this actually makes sense? I am not an expert on how hardware is handling offloading here. But if I am not wrong, as the interface is set on promiscuous or offload enabled. For promiscuous this does not matter and for the offloaded scenario shouldn't the decision be handled by hardware and not depend on ndo_set_mac_address()?

Let me know if I am missing something here.

Anyway, the missing notification makes sense and should be fixed for SLAVE_B.

Thanks,
Fernando.

#6 lore raw
Quoted 140 lines · Fernando Fernandez Mancera
Quoted 125 lines · Fernando Fernandez Mancera
Quoted 114 lines · Luka Gejak
Quoted 76 lines · Fernando Fernandez Mancera

In order to work properly PRP requires slave1 and slave2 to share the same MAC address. To ease the configuration process on userspace tools, sync the slave2 MAC address with slave1. In addition, when deleting the port from the list, restore the original MAC address.

---
v3: restore the original MAC address on slave removal.
---
  net/hsr/hsr_device.c | 5 +++++ net/hsr/hsr_main.c   | 9 +++++++++ net/hsr/hsr_main.h   | 1 + net/hsr/hsr_slave.c  | 2 ++

  4 files changed, 17 insertions(+)
net/hsr/hsr_device.c +5 -0
index 439cfb7ad5d1..e8922e8d9398 100644
@@ -761,6 +761,11 @@ int hsr_dev_finalize(struct net_device *hsr_dev, 
 struct net_device *slave[2],
       if (res)
           goto err_unregister;
+    if (protocol_version == PRP_V1) {
+        eth_hw_addr_set(slave[1], slave[0]->dev_addr);
+        call_netdevice_notifiers(NETDEV_CHANGEADDR, slave[1]);
+    }
+
       if (interlink) {
           res = hsr_add_port(hsr, interlink, HSR_PT_INTERLINK, extack);
           if (res)
net/hsr/hsr_main.c +9 -0
index d7ae32473c41..192893c3f2ec 100644
@@ -78,6 +78,15 @@ static int hsr_netdev_notify(struct notifier_block 
 *nb, unsigned long event,
               eth_hw_addr_set(master->dev, dev->dev_addr);
               call_netdevice_notifiers(NETDEV_CHANGEADDR,
                            master->dev);
+
+            if (hsr->prot_version == PRP_V1) {
+                port = hsr_port_get_hsr(hsr, HSR_PT_SLAVE_B);
+                if (port) {
+                    eth_hw_addr_set(port->dev, dev->dev_addr);
+                    call_netdevice_notifiers(NETDEV_CHANGEADDR,
+                                 port->dev);
+                }
+            }
           }
           /* Make sure we recognize frames from ourselves in 

hsr_rcv() */

net/hsr/hsr_main.h +1 -0
index 1bc47b17a296..135ec5fce019 100644
@@ -155,6 +155,7 @@ struct hsr_port {
       struct hsr_priv        *hsr;
       enum hsr_port_type    type;
       struct rcu_head        rcu;
+    unsigned char        original_macaddress[ETH_ALEN];
   };
   struct hsr_frame_info;
net/hsr/hsr_slave.c +1 -0
index 2a802a5de2ac..b87b6a6fe070 100644
@@ -196,6 +196,7 @@ int hsr_add_port(struct hsr_priv *hsr, struct 
 net_device *dev,
       port->hsr = hsr;
       port->dev = dev;
       port->type = type;
+    ether_addr_copy(port->original_macaddress, dev->dev_addr);
       if (type != HSR_PT_MASTER) {
           res = hsr_portdev_setup(hsr, dev, port, extack);

net/hsr/hsr_slave.c void hsr_del_port(struct hsr_port *port) · line 238

Quoted 6 lines
net/hsr/hsr_slave.c +1 -0
@@ -232,6 +233,7 @@ void hsr_del_port(struct hsr_port *port)
           if (!port->hsr->fwd_offloaded)
               dev_set_promiscuity(port->dev, -1);
           netdev_upper_dev_unlink(port->dev, master->dev);
+        eth_hw_addr_set(port->dev, port->original_macaddress);
       }
       kfree_rcu(port, rcu);

Hi Fernando,

Thanks for the patch. The logic to sync the slave2 MAC address with slave1 for PRP is sound, but there are a few implementation issues here that will cause hardware filtering problems and style violations.

1. Hardware MAC Filtering
In your current implementation:

   if (protocol_version == PRP_V1) {

       eth_hw_addr_set(slave[1], slave[0]->dev_addr);

       call_netdevice_notifiers(NETDEV_CHANGEADDR, slave[1]);

   }

eth_hw_addr_set() is appropriate for virtual devices (like the hsr_dev itself), but slave[1] is a physical net_device. By using this helper, you are bypassing dev->netdev_ops->ndo_set_mac_address. This means the physical NIC's hardware MAC filter will not be programmed, and it will silently drop unicast traffic destined for the new PRP MAC address unless the interface happens to be in promiscuous mode. You should use dev_set_mac_address() here instead. Note that unlike eth_hw_addr_set(), dev_set_mac_address() can fail and returns an error code, so you will need to check its return value and handle the error path accordingly.

2. Teardown Notifiers
In hsr_del_port():

Quoted 9 lines

   netdev_upper_dev_unlink(port->dev, master->dev); eth_hw_addr_set(port->dev, port->original_macaddress);

You have the same issue with eth_hw_addr_set() here. Additionally, unlike the setup paths, this version omits call_netdevice_notifiers (NETDEV_CHANGEADDR, port->dev). Switching to dev_set_mac_address() for the restoration will handle both the hardware programming and the notifier chain automatically.

Quoted 7 lines

These points makes sense. I guess I didn't notice the that eth_hw_addr_set() due to my interface being set to promiscuous mode at hsr_slave.c.

Let me research a bit more about the impact here and will get back to you either with a new patch or an reply here.

Does this actually makes sense? I am not an expert on how hardware is handling offloading here. But if I am not wrong, as the interface is set on promiscuous or offload enabled. For promiscuous this does not matter and for the offloaded scenario shouldn't the decision be handled by hardware and not depend on ndo_set_mac_address()?

Quoted 8 lines

Let me know if I am missing something here.

Anyway, the missing notification makes sense and should be fixed for SLAVE_B.

Thanks,
Fernando.

Hi Fernando,
You raise a fair point, and I should have looked more carefully at the existing code paths.

You are correct that in the non-offloaded case, hsr_slave.c already sets promiscuous mode via dev_set_promiscuity(dev, 1), so the hardware MAC filter is bypassed and eth_hw_addr_set() is sufficient for frame reception.

For the offloaded case, the comment in hsr_portdev_setup() notes that "L2 frame forward happens at the offloaded hardware" — so the hardware is configured through its own HSR/PRP offload mechanisms, not through ndo_set_mac_address().

So the practical impact of my original concern is limited to edge cases where promiscuous mode might be disabled or fail. The more important issue, which you've already acknowledged, is the missing notifier in hsr_del_port(). That should definitely be fixed for correctness.

One additional consideration: even though promiscuous mode handles the receive path, dev->dev_addr is still used as the source MAC for outgoing frames. Using dev_set_mac_address() would ensure the software state (dev->dev_addr) and any driver-level state remain consistent. But I agree this is less critical than I initially suggested. Thanks for pushing back on this — it's a good clarification.

Best regards,
Luka

#7 lore raw
Quoted 169 lines · Luka Gejak
Quoted 140 lines · Fernando Fernandez Mancera
Quoted 125 lines · Fernando Fernandez Mancera
Quoted 114 lines · Luka Gejak
Quoted 76 lines · Fernando Fernandez Mancera

In order to work properly PRP requires slave1 and slave2 to share the same MAC address. To ease the configuration process on userspace tools, sync the slave2 MAC address with slave1. In addition, when deleting the port from the list, restore the original MAC address.

---
v3: restore the original MAC address on slave removal.

---
   net/hsr/hsr_device.c | 5 +++++
   net/hsr/hsr_main.c   | 9 +++++++++
   net/hsr/hsr_main.h   | 1 +
   net/hsr/hsr_slave.c  | 2 ++
   4 files changed, 17 insertions(+)
net/hsr/hsr_device.c +5 -0
index 439cfb7ad5d1..e8922e8d9398 100644
@@ -761,6 +761,11 @@ int hsr_dev_finalize(struct net_device *hsr_dev,
 struct net_device *slave[2],
       if (res)
           goto err_unregister;
+    if (protocol_version == PRP_V1) {
+        eth_hw_addr_set(slave[1], slave[0]->dev_addr);
+        call_netdevice_notifiers(NETDEV_CHANGEADDR, slave[1]);
+    }
+
       if (interlink) {
           res = hsr_add_port(hsr, interlink, HSR_PT_INTERLINK, extack);
           if (res)
net/hsr/hsr_main.c +9 -0
index d7ae32473c41..192893c3f2ec 100644
@@ -78,6 +78,15 @@ static int hsr_netdev_notify(struct notifier_block
 *nb, unsigned long event,
               eth_hw_addr_set(master->dev, dev->dev_addr);
               call_netdevice_notifiers(NETDEV_CHANGEADDR,
                            master->dev);
+
+            if (hsr->prot_version == PRP_V1) {
+                port = hsr_port_get_hsr(hsr, HSR_PT_SLAVE_B);
+                if (port) {
+                    eth_hw_addr_set(port->dev, dev->dev_addr);
+                    call_netdevice_notifiers(NETDEV_CHANGEADDR,
+                                 port->dev);
+                }
+            }
           }
           /* Make sure we recognize frames from ourselves in

hsr_rcv() */

net/hsr/hsr_main.h +1 -0
index 1bc47b17a296..135ec5fce019 100644
@@ -155,6 +155,7 @@ struct hsr_port {
       struct hsr_priv        *hsr;
       enum hsr_port_type    type;
       struct rcu_head        rcu;
+    unsigned char        original_macaddress[ETH_ALEN];
   };
   struct hsr_frame_info;
net/hsr/hsr_slave.c +1 -0
index 2a802a5de2ac..b87b6a6fe070 100644
@@ -196,6 +196,7 @@ int hsr_add_port(struct hsr_priv *hsr, struct
 net_device *dev,
       port->hsr = hsr;
       port->dev = dev;
       port->type = type;
+    ether_addr_copy(port->original_macaddress, dev->dev_addr);
       if (type != HSR_PT_MASTER) {
           res = hsr_portdev_setup(hsr, dev, port, extack);

net/hsr/hsr_slave.c void hsr_del_port(struct hsr_port *port) · line 238

Quoted 6 lines
net/hsr/hsr_slave.c +1 -0
@@ -232,6 +233,7 @@ void hsr_del_port(struct hsr_port *port)
           if (!port->hsr->fwd_offloaded)
               dev_set_promiscuity(port->dev, -1);
           netdev_upper_dev_unlink(port->dev, master->dev);
+        eth_hw_addr_set(port->dev, port->original_macaddress);
       }
       kfree_rcu(port, rcu);

Hi Fernando,

Thanks for the patch. The logic to sync the slave2 MAC address with slave1 for PRP is sound, but there are a few implementation issues here that will cause hardware filtering problems and style violations.

1. Hardware MAC Filtering
In your current implementation:

   if (protocol_version == PRP_V1) {

       eth_hw_addr_set(slave[1], slave[0]->dev_addr);

       call_netdevice_notifiers(NETDEV_CHANGEADDR, slave[1]);

   }

eth_hw_addr_set() is appropriate for virtual devices (like the hsr_dev itself), but slave[1] is a physical net_device. By using this helper, you are bypassing dev->netdev_ops->ndo_set_mac_address. This means the physical NIC's hardware MAC filter will not be programmed, and it will silently drop unicast traffic destined for the new PRP MAC address unless the interface happens to be in promiscuous mode. You should use dev_set_mac_address() here instead. Note that unlike eth_hw_addr_set(), dev_set_mac_address() can fail and returns an error code, so you will need to check its return value and handle the error path accordingly.

2. Teardown Notifiers
In hsr_del_port():

Quoted 9 lines

   netdev_upper_dev_unlink(port->dev, master->dev); eth_hw_addr_set(port->dev, port->original_macaddress);

You have the same issue with eth_hw_addr_set() here. Additionally, unlike the setup paths, this version omits call_netdevice_notifiers (NETDEV_CHANGEADDR, port->dev). Switching to dev_set_mac_address() for the restoration will handle both the hardware programming and the notifier chain automatically.

Quoted 7 lines

These points makes sense. I guess I didn't notice the that eth_hw_addr_set() due to my interface being set to promiscuous mode at hsr_slave.c.

Let me research a bit more about the impact here and will get back to you either with a new patch or an reply here.

Does this actually makes sense? I am not an expert on how hardware is handling offloading here. But if I am not wrong, as the interface is set on promiscuous or offload enabled. For promiscuous this does not matter and for the offloaded scenario shouldn't the decision be handled by hardware and not depend on ndo_set_mac_address()?

Quoted 8 lines

Let me know if I am missing something here.

Anyway, the missing notification makes sense and should be fixed for SLAVE_B.

Thanks,
Fernando.

Hi Fernando,
You raise a fair point, and I should have looked more carefully at the existing code paths.

You are correct that in the non-offloaded case, hsr_slave.c already sets promiscuous mode via dev_set_promiscuity(dev, 1), so the hardware MAC filter is bypassed and eth_hw_addr_set() is sufficient for frame reception.

For the offloaded case, the comment in hsr_portdev_setup() notes that "L2 frame forward happens at the offloaded hardware" — so the hardware is configured through its own HSR/PRP offload mechanisms, not through ndo_set_mac_address().

So the practical impact of my original concern is limited to edge cases where promiscuous mode might be disabled or fail. The more important issue, which you've already acknowledged, is the missing notifier in hsr_del_port(). That should definitely be fixed for correctness.

Quoted 4 lines

One additional consideration: even though promiscuous mode handles the receive path, dev->dev_addr is still used as the source MAC for outgoing frames. Using dev_set_mac_address() would ensure the software state (dev->dev_addr)

I am sorry I do not follow here. eth_hw_addr_set() path ends up calling dev_addr_mod() which modifies dev->dev_addr indeed.

Thanks,
Fernando.

and any driver-level state remain consistent. But

Quoted 6 lines

I agree this is less critical than I initially suggested. Thanks for pushing back on this — it's a good clarification.

Best regards,
Luka

#8 lore raw
In reply to Luka Gejak

Hi Luka,

Quoted 176 lines · Fernando Fernandez Mancera
Quoted 146 lines · Fernando Fernandez Mancera
Quoted 130 lines · Luka Gejak
Quoted 122 lines
Quoted 77 lines · Fernando Fernandez Mancera

In order to work properly PRP requires slave1 and slave2 to share the same MAC address. To ease the configuration process on userspace tools, sync the slave2 MAC address with slave1. In addition, when deleting the port from the list, restore the original MAC address.

---
v3: restore the original MAC address on slave removal.
---
  net/hsr/hsr_device.c | 5 +++++ net/hsr/hsr_main.c   | 9 +++++++++ net/hsr/hsr_main.h   | 1 + net/hsr/hsr_slave.c  | 2 ++

  4 files changed, 17 insertions(+)
net/hsr/hsr_device.c +5 -0
index 439cfb7ad5d1..e8922e8d9398 100644
@@ -761,6 +761,11 @@ int hsr_dev_finalize(struct net_device
 *hsr_dev, struct net_device *slave[2],
       if (res)
           goto err_unregister;
+    if (protocol_version == PRP_V1) {
+        eth_hw_addr_set(slave[1], slave[0]->dev_addr);
+        call_netdevice_notifiers(NETDEV_CHANGEADDR, slave[1]);
+    }
+
       if (interlink) {
           res = hsr_add_port(hsr, interlink, HSR_PT_INTERLINK,
 extack); if (res)
net/hsr/hsr_main.c +9 -0
index d7ae32473c41..192893c3f2ec 100644
@@ -78,6 +78,15 @@ static int hsr_netdev_notify(struct
 notifier_block *nb, unsigned long event,
               eth_hw_addr_set(master->dev, dev->dev_addr);
               call_netdevice_notifiers(NETDEV_CHANGEADDR,
                            master->dev);
+
+            if (hsr->prot_version == PRP_V1) {
+                port = hsr_port_get_hsr(hsr, HSR_PT_SLAVE_B);
+                if (port) {
+                    eth_hw_addr_set(port->dev, dev->dev_addr);
+                    call_netdevice_notifiers(NETDEV_CHANGEADDR,
+                                 port->dev);
+                }
+            }
           }
           /* Make sure we recognize frames from ourselves in 

hsr_rcv() */

net/hsr/hsr_main.h +1 -0
index 1bc47b17a296..135ec5fce019 100644
@@ -155,6 +155,7 @@ struct hsr_port {
       struct hsr_priv        *hsr;
       enum hsr_port_type    type;
       struct rcu_head        rcu;
+    unsigned char        original_macaddress[ETH_ALEN];
   };
   struct hsr_frame_info;
net/hsr/hsr_slave.c +1 -0
index 2a802a5de2ac..b87b6a6fe070 100644
@@ -196,6 +196,7 @@ int hsr_add_port(struct hsr_priv *hsr,
 struct net_device *dev,
       port->hsr = hsr;
       port->dev = dev;
       port->type = type;
+    ether_addr_copy(port->original_macaddress, dev->dev_addr);
       if (type != HSR_PT_MASTER) {
           res = hsr_portdev_setup(hsr, dev, port, extack);

net/hsr/hsr_slave.c void hsr_del_port(struct hsr_port *port) · line 238

Quoted 6 lines
net/hsr/hsr_slave.c +1 -0
@@ -232,6 +233,7 @@ void hsr_del_port(struct hsr_port *port)
           if (!port->hsr->fwd_offloaded)
               dev_set_promiscuity(port->dev, -1);
           netdev_upper_dev_unlink(port->dev, master->dev);
+        eth_hw_addr_set(port->dev, port->original_macaddress);
       }
       kfree_rcu(port, rcu);  

Hi Fernando,

Thanks for the patch. The logic to sync the slave2 MAC address with slave1 for PRP is sound, but there are a few implementation issues here that will cause hardware filtering problems and style violations.

1. Hardware MAC Filtering
In your current implementation:

   if (protocol_version == PRP_V1) {

       eth_hw_addr_set(slave[1], slave[0]->dev_addr);

       call_netdevice_notifiers(NETDEV_CHANGEADDR, slave[1]);

   }

eth_hw_addr_set() is appropriate for virtual devices (like the hsr_dev itself), but slave[1] is a physical net_device. By using this helper, you are bypassing dev->netdev_ops->ndo_set_mac_address. This means the physical NIC's hardware MAC filter will not be programmed, and it will silently drop unicast traffic destined for the new PRP MAC address unless the interface happens to be in promiscuous mode. You should use dev_set_mac_address() here instead. Note that unlike eth_hw_addr_set(), dev_set_mac_address() can fail and returns an error code, so you will need to check its return value and handle the error path accordingly.

2. Teardown Notifiers
In hsr_del_port():

   netdev_upper_dev_unlink(port->dev, master->dev); eth_hw_addr_set(port->dev, port->original_macaddress);

Quoted 6 lines

You have the same issue with eth_hw_addr_set() here. Additionally, unlike the setup paths, this version omits call_netdevice_notifiers (NETDEV_CHANGEADDR, port->dev). Switching to dev_set_mac_address() for the restoration will handle both the hardware programming and the notifier chain automatically.

Quoted 7 lines

These points makes sense. I guess I didn't notice the that eth_hw_addr_set() due to my interface being set to promiscuous mode at hsr_slave.c.

Let me research a bit more about the impact here and will get back to you either with a new patch or an reply here.

Does this actually makes sense? I am not an expert on how hardware is handling offloading here. But if I am not wrong, as the interface is set on promiscuous or offload enabled. For promiscuous this does not matter and for the offloaded scenario shouldn't the decision be handled by hardware and not depend on ndo_set_mac_address()?

Quoted 8 lines

Let me know if I am missing something here.

Anyway, the missing notification makes sense and should be fixed for SLAVE_B.

Thanks,
Fernando.

Hi Fernando,
You raise a fair point, and I should have looked more carefully at the existing code paths.

You are correct that in the non-offloaded case, hsr_slave.c already sets promiscuous mode via dev_set_promiscuity(dev, 1), so the hardware MAC filter is bypassed and eth_hw_addr_set() is sufficient for frame reception.

For the offloaded case, the comment in hsr_portdev_setup() notes that "L2 frame forward happens at the offloaded hardware" — so the hardware is configured through its own HSR/PRP offload mechanisms, not through ndo_set_mac_address().

So the practical impact of my original concern is limited to edge cases where promiscuous mode might be disabled or fail. The more important issue, which you've already acknowledged, is the missing notifier in hsr_del_port(). That should definitely be fixed for correctness.

Quoted 8 lines

One additional consideration: even though promiscuous mode handles the receive path, dev->dev_addr is still used as the source MAC for outgoing frames. Using dev_set_mac_address() would ensure the software state (dev->dev_addr) and any driver-level state remain consistent. But I agree this is less critical than I initially suggested. Thanks for pushing back on this — it's a good clarification.

Thanks for your patches - as denx.de is not operational anymore (now I do work for nabladev.com) I've just stumbled upon your patches.

I'm very happy that PRP now also gains support :-)

Quoted 2 lines

Best regards,
Luka

Signature · 10 lines
Best regards,

Lukasz Majewski

--
Nabla Software Engineering GmbH
HRB 40522 Augsburg
Phone: +49 821 45592596
E-Mail: [email protected]
Managing Director : Stefano Babic