Skip to contentSkip to conversation

add loongson mips ls1c300 initial support

PATCH New [email protected] 1 participant 8 messages Apr 3

Subsystems (6)
lore
Share & tools
lore
#0 lore raw

v7 cover add loongson mips ls1c300 initial support

From: Du Huanpeng <[email protected]>

---
Du Huanpeng (7):
mips: loongson: minimal initial SoC support
mips: loongson: lowlevel initialize
mips: loongson: lowlevel debug serial
mips: loongson: ls1c300 board support
mips: loongson: add clk driver
mips: loongson: add watchdog driver
mips: loongson: ls1c300 dts and bindings

 MAINTAINERS                                   |   9 +
 arch/mips/Kconfig                             |  11 ++
 arch/mips/Makefile                            |   1 +
 arch/mips/dts/loongson32-ls1c300b.dtsi        | 151 ++++++++++++++
 arch/mips/dts/ls1c300-eval.dts                |  30 +++
 arch/mips/mach-loongson/Kconfig               |  69 +++++++
 arch/mips/mach-loongson/Makefile              |   6 +
 arch/mips/mach-loongson/cpu.c                 |  19 ++
 arch/mips/mach-loongson/include/mach/serial.h |  16 ++
 arch/mips/mach-loongson/ls1c300/Makefile      |   7 +
 arch/mips/mach-loongson/ls1c300/gpio.c        |  66 +++++++
 arch/mips/mach-loongson/ls1c300/init.c        |  61 ++++++
 .../mach-loongson/ls1c300/lowlevel_init.S     | 134 +++++++++++++
 arch/mips/mach-loongson/ls1c300/sdram.S       |  95 +++++++++
 arch/mips/mach-loongson/ls1c300/serial.c      | 104 ++++++++++
 arch/mips/mach-loongson/spl.c                 |  46 +++++
 board/loongson/ls1c300-eval/Kconfig           |  12 ++
 board/loongson/ls1c300-eval/MAINTAINERS       |   7 +
 board/loongson/ls1c300-eval/Makefile          |   3 +
 board/loongson/ls1c300-eval/board.c           |  19 ++
 configs/ls1c300_defconfig                     |  52 +++++
 drivers/clk/Makefile                          |   1 +
 drivers/clk/loongson/Makefile                 |   3 +
 drivers/clk/loongson/clk-ls1c300.c            | 186 ++++++++++++++++++
 drivers/watchdog/Kconfig                      |   8 +
 drivers/watchdog/Makefile                     |   1 +
 drivers/watchdog/loongson_wdt.c               | 127 ++++++++++++
 include/configs/ls1c300.h                     |  38 ++++
 include/dt-bindings/clock/ls1c300-clk.h       |  18 ++
 include/dt-bindings/reset/ls1c300-reset.h     |  36 ++++
 30 files changed, 1336 insertions(+)
 create mode 100644 arch/mips/dts/loongson32-ls1c300b.dtsi
 create mode 100644 arch/mips/dts/ls1c300-eval.dts
 create mode 100644 arch/mips/mach-loongson/Kconfig
 create mode 100644 arch/mips/mach-loongson/Makefile
 create mode 100644 arch/mips/mach-loongson/cpu.c
 create mode 100644 arch/mips/mach-loongson/include/mach/serial.h
 create mode 100644 arch/mips/mach-loongson/ls1c300/Makefile
 create mode 100644 arch/mips/mach-loongson/ls1c300/gpio.c
 create mode 100644 arch/mips/mach-loongson/ls1c300/init.c
 create mode 100644 arch/mips/mach-loongson/ls1c300/lowlevel_init.S
 create mode 100644 arch/mips/mach-loongson/ls1c300/sdram.S
 create mode 100644 arch/mips/mach-loongson/ls1c300/serial.c
 create mode 100644 arch/mips/mach-loongson/spl.c
 create mode 100644 board/loongson/ls1c300-eval/Kconfig
 create mode 100644 board/loongson/ls1c300-eval/MAINTAINERS
 create mode 100644 board/loongson/ls1c300-eval/Makefile
 create mode 100644 board/loongson/ls1c300-eval/board.c
 create mode 100644 configs/ls1c300_defconfig
 create mode 100644 drivers/clk/loongson/Makefile
 create mode 100644 drivers/clk/loongson/clk-ls1c300.c
 create mode 100644 drivers/watchdog/loongson_wdt.c
 create mode 100644 include/configs/ls1c300.h
 create mode 100644 include/dt-bindings/clock/ls1c300-clk.h
 create mode 100644 include/dt-bindings/reset/ls1c300-reset.h
Signature · 1 line
2.43.0
#1 lore raw

PATCH v7 1/7 mips: loongson: minimal initial SoC support

From: Du Huanpeng <[email protected]>

Loongson 1C is a cost-effective SOC chip for industrial control and the Internet of Things. The Loongson 1C includes a floating-point processing unit, supports multiple types of memory, and supports high-capacity MLC NAND Flash. Loongson 1C provides developers with a wealth of peripheral interfaces and on-chip modules, including Camera controller, USB OTG and USB HOST interfaces, AC97/I2S controller, LCD controller, SPI interface, UART interface, etc., providing sufficient computing power and multi-application connectivity.

Some highlights of this SoC are:
- Single core LS232, MIPS32 instruction set compatible, main frequency 300MHZ
- 16KB data cache and 16KB instruction cache
- 64 bit float unit, hardware division
- 8/16 bit SDRAM controller, 45 ~ 133MHz
- 8/16 bit SRAM, NAND
- I2S/AC97, LCD, MAC, USB, OTG, SPI, I2C, PWM, CAN, SDIO, ADC
- 12 UARTs

Links:
https://www.loongson.cn/

introduce base support for the ls1c300 SoC.
- debug UART2
- serial console
- clock
- watchdog
- sysreset
- uart

---
 MAINTAINERS                              |  9 ++++
 arch/mips/Kconfig                        | 11 ++++
 arch/mips/Makefile                       |  1 +
 arch/mips/mach-loongson/Kconfig          | 69 ++++++++++++++++++++++++
 arch/mips/mach-loongson/Makefile         |  6 +++
 arch/mips/mach-loongson/cpu.c            | 19 +++++++
 arch/mips/mach-loongson/ls1c300/Makefile |  7 +++
 arch/mips/mach-loongson/ls1c300/init.c   | 61 +++++++++++++++++++++
 arch/mips/mach-loongson/spl.c            | 46 ++++++++++++++++
 9 files changed, 229 insertions(+)
 create mode 100644 arch/mips/mach-loongson/Kconfig
 create mode 100644 arch/mips/mach-loongson/Makefile
 create mode 100644 arch/mips/mach-loongson/cpu.c
 create mode 100644 arch/mips/mach-loongson/ls1c300/Makefile
 create mode 100644 arch/mips/mach-loongson/ls1c300/init.c
 create mode 100644 arch/mips/mach-loongson/spl.c
MAINTAINERS +9 -0
index d4b527560aa..11d56d9795d 100644
@@ -1379,6 +1379,15 @@ F:	drivers/net/cortina_ni.c
 F:	drivers/net/cortina_ni.h
 F:	drivers/net/phy/ca_phy.c
 
+MIPS LOONGSON LS1C300
+M:	Du Huanpeng <[email protected]>
+S:	Maintained
+F:	arch/mips/dts/loongson32-ls1c300b.dtsi
+F:	arch/mips/mach-loongson/
+F:	drivers/clk/loongson/
+F:	drivers/watchdog/loongson_wdt.c
+F:	include/dt-bindings/clock/ls1c300-clk.h
+
 MIPS MEDIATEK
 M:	Weijie Gao <[email protected]>
 R:	GSS_MTK_Uboot_upstream <[email protected]>
arch/mips/Kconfig +11 -0
index 36612756294..0e3fc9ceeb5 100644
@@ -88,6 +88,16 @@ config ARCH_MTMIPS
 	select SUPPORT_LITTLE_ENDIAN
 	select SUPPORT_SPL
 
+config ARCH_LSMIPS
+	bool "Support Loongson MIPS platforms"
+	select DM
+	select DM_SERIAL
+	select OF_CONTROL
+	select SUPPORTS_CPU_MIPS32_R1
+	select SUPPORTS_CPU_MIPS32_R2
+	select SUPPORTS_LITTLE_ENDIAN
+	select SUPPORT_SPL
+
 config ARCH_JZ47XX
 	bool "Support Ingenic JZ47xx"
 	select SUPPORT_SPL
@@ -202,6 +212,7 @@ source "arch/mips/mach-bmips/Kconfig"
 source "arch/mips/mach-jz47xx/Kconfig"
 source "arch/mips/mach-pic32/Kconfig"
 source "arch/mips/mach-mtmips/Kconfig"
+source "arch/mips/mach-loongson/Kconfig"
 source "arch/mips/mach-octeon/Kconfig"
 
 if MIPS
arch/mips/Makefile +1 -0
index 453c7885075..72b800c755b 100644
@@ -19,6 +19,7 @@ machine-$(CONFIG_ARCH_BMIPS) += bmips
 machine-$(CONFIG_ARCH_JZ47XX) += jz47xx
 machine-$(CONFIG_MACH_PIC32) += pic32
 machine-$(CONFIG_ARCH_MTMIPS) += mtmips
+machine-$(CONFIG_ARCH_LSMIPS) += loongson
 machine-$(CONFIG_ARCH_MSCC) += mscc
 machine-${CONFIG_ARCH_OCTEON} += octeon
 
arch/mips/mach-loongson/Kconfig new file +69 -0

69 lines not on this page · raw message

arch/mips/mach-loongson/Makefile new file +6 -0
new file mode 100644
index 00000000000..654143a5f70
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+obj-y += cpu.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
+
+obj-$(CONFIG_SOC_LS1C300) += ls1c300/
arch/mips/mach-loongson/cpu.c new file +19 -0
new file mode 100644
index 00000000000..249fdcbdc5f
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Stefan Roese <[email protected]>
+ * Copyright (C) 2022-2026 Du Huanpeng <[email protected]>
+ */
+
+#include <init.h>
+#include <malloc.h>
+#include <linux/bitops.h>
+#include <linux/io.h>
+#include <linux/sizes.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)KSEG1, SZ_256M) - CONFIG_TEXT_BASE % SZ_256M;
+	return 0;
+}
arch/mips/mach-loongson/ls1c300/Makefile new file +7 -0
new file mode 100644
index 00000000000..17b9d6fb9ca
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-y += lowlevel_init.o
+obj-y += sdram.o
+obj-y += init.o
+obj-y += gpio.o
+obj-$(CONFIG_SPL_BUILD) += serial.o
arch/mips/mach-loongson/ls1c300/init.c new file +61 -0

61 lines not on this page · raw message

arch/mips/mach-loongson/spl.c new file +46 -0

46 lines not on this page · raw message

Signature · 1 line
2.43.0
#2 lore raw

PATCH v7 2/7 mips: loongson: lowlevel initialize

In reply to [email protected]

From: Du Huanpeng <[email protected]>

- pll
- spi controller
- sdram

---
 .../mach-loongson/ls1c300/lowlevel_init.S     | 134 ++++++++++++++++++
 arch/mips/mach-loongson/ls1c300/sdram.S       |  95 +++++++++++++
 2 files changed, 229 insertions(+)
 create mode 100644 arch/mips/mach-loongson/ls1c300/lowlevel_init.S
 create mode 100644 arch/mips/mach-loongson/ls1c300/sdram.S
arch/mips/mach-loongson/ls1c300/lowlevel_init.S new file +134 -0
new file mode 100644
index 00000000000..8d9ba97130c
@@ -0,0 +1,134 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2020 MediaTek Inc.
+ *
+ * Author:  Gao Weijie <[email protected]>
+ *
+ * Copyright (C) 2020-2023 Du Huanpeng <[email protected]>
+ */
+
+#include <config.h>
+#include <asm-offsets.h>
+#include <asm/cacheops.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+#include <asm/addrspace.h>
+#include <asm/asm.h>
+#include <linux/sizes.h>
+
+/* PLL control register */
+#define NAND_BASE	0xbfe70000
+#define START_FREQ	0x8030
+#define CLK_DIV_PARAM	0x8034
+#define CPU_THROT	0xc010
+
+/* START_FREQ */
+#define PLL_VALID	31
+#define Reserved_24	24
+#define FRAC_N		16
+#define M_PLL		8
+#define Reserved_4	4
+#define RST_TIME	2
+#define SDRAM_DIV	0
+ #define SDRAM_DIV2	0
+ #define SDRAM_DIV4	1
+ #define SDRAM_DIV3	2
+
+/* CLK_DIV_PARAM */
+#define PIX_DIV		24
+#define CAM_DIV		16
+#define CPU_DIV		8
+#define PIX_DIV_VALID	5
+#define PIX_SEL		4
+#define CAM_DIV_VALID	3
+#define CAM_SEL		2
+#define CPU_DIV_VALID	1
+#define CPU_SEL		0
+
+/* Document:
+ * Freq_PLL = XIN *(M_PLL + FRAC_N)/4
+ */
+#define XIN			24000000
+#define PLL_VALID_1		(1<<PLL_VALID)
+#define PREP_M_PLL(Freq_PLL)	(((Freq_PLL * 4) / XIN) << M_PLL)
+#define PREP_SDRAM_DIV(div)	(div<<SDRAM_DIV)
+#define PREP_CPU_DIV(div1)	((0x80|div1)<<CPU_DIV | (div1&&div1)<<CPU_DIV_VALID)
+#define PREP_PIX_DIV(div2)	(div2<<PIX_DIV)
+#define PREP_CAM_DIV(div3)	(div3<<CAM_DIV)
+
+/* PLL @264MHz, CPU @132MHz, SDRAM @66MHz */
+#define CFG_START_FREQ		(PLL_VALID_1 | PREP_M_PLL(264000000) | SDRAM_DIV2)
+#define CFG_CLK_DIV_PARAM	(PREP_CPU_DIV(2) | PREP_PIX_DIV(0x24) | PREP_CAM_DIV(0x24))
+#define CFG_CPU_THROT		15
+
+/* SPI0 control register */
+#define SPI0_BASE		0xbfe80000
+#define SPCR			0
+#define SPSR			1
+#define TxFIFO			2
+#define RxFIFO			2
+#define SPER			3
+#define SFC_PARAM		4
+    #define CLK_DIV		4
+    #define DUAL_IO		3
+    #define FAST_READ		2
+    #define BURST_EN		1
+    #define MEMORY_EN		0
+#define SFC_SOFTCS		5
+#define SFC_TIMING		6
+    #define T_FAST		2
+    #define T_CSH		0
+
+	.set noreorder
+LEAF(ls1c300_pll_init)
+#if !CONFIG_IS_ENABLED(SKIP_LOWLEVEL_INIT)
+	li	t0, NAND_BASE
+	li	t1, CFG_START_FREQ
+	li	t2, CFG_CLK_DIV_PARAM
+	li	t3, CFG_CPU_THROT
+
+	sw	t3, CPU_THROT (t0)
+	sw	t2, CLK_DIV_PARAM (t0)
+	sw	t1, START_FREQ (t0)
+
+	ori	t2, 1<<CPU_SEL
+	sw	t2, CLK_DIV_PARAM (t0)
+#endif
+	jr	ra
+	 nop
+END(ls1c300_pll_init)
+
+LEAF(ls1c300_spi_init)
+#if !CONFIG_IS_ENABLED(SKIP_LOWLEVEL_INIT)
+	li	t0, SPI0_BASE
+	li	t1, (1<<MEMORY_EN) | (1<<BURST_EN) | (1<<FAST_READ) | (1<<DUAL_IO)
+	sb	t1, SFC_PARAM (t0)
+	li	t2, (1<<T_FAST) | (1<<T_CSH)
+	sb	t2, SFC_TIMING (t0)
+#endif
+	jr	ra
+	  nop
+END(ls1c300_spi_init)
+
+NESTED(lowlevel_init, 0, ra)
+	/* Save ra and do real lowlevel initialization */
+	move	s0, ra
+	/* Setup PLL @264MHz */
+	PTR_LA	t9, ls1c300_pll_init
+	jalr	t9
+	  nop
+
+	/* Setup SPI Dual IO@33MHz */
+	PTR_LA	t9, ls1c300_spi_init
+	jalr	t9
+	  nop
+
+	/* Setup external SDRAM @66MHz */
+	PTR_LA	t9, ls1c300_sdram_init
+	jalr	t9
+	  nop
+
+	move	ra, s0
+	jr	ra
+	 nop
+END(lowlevel_init)
arch/mips/mach-loongson/ls1c300/sdram.S new file +95 -0

95 lines not on this page · raw message

Signature · 1 line
2.43.0
#3 lore raw

PATCH v7 3/7 mips: loongson: lowlevel debug serial

In reply to [email protected]

From: Du Huanpeng <[email protected]>

set pin to uart alternate function and enable uart for lowlevel debug, also future pinctrl driver can base on this code.

---
 arch/mips/mach-loongson/include/mach/serial.h |  16 +++
 arch/mips/mach-loongson/ls1c300/gpio.c        |  66 +++++++++++
 arch/mips/mach-loongson/ls1c300/serial.c      | 104 ++++++++++++++++++
 3 files changed, 186 insertions(+)
 create mode 100644 arch/mips/mach-loongson/include/mach/serial.h
 create mode 100644 arch/mips/mach-loongson/ls1c300/gpio.c
 create mode 100644 arch/mips/mach-loongson/ls1c300/serial.c
arch/mips/mach-loongson/include/mach/serial.h new file +16 -0
new file mode 100644
index 00000000000..7afe5788cb7
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2020 MediaTek Inc.
+ *
+ * Author:  Gao Weijie <[email protected]>
+ *
+ * Copyright (C) 2022 Du Huanpeng <[email protected]>
+ */
+
+#ifndef __LSMIPS_SERIAL_H_
+#define __LSMIPS_SERIAL_H_
+
+void loongson_spl_serial_init(void);
+int gpio_set_alternate(int gpio, int func);
+
+#endif /* __LSMIPS_SERIAL_H_ */
arch/mips/mach-loongson/ls1c300/gpio.c new file +66 -0

66 lines not on this page · raw message

arch/mips/mach-loongson/ls1c300/serial.c new file +104 -0

104 lines not on this page · raw message

Signature · 1 line
2.43.0
#4 lore raw

PATCH v7 4/7 mips: loongson: ls1c300 board support

In reply to [email protected]

From: Du Huanpeng <[email protected]>

- 64MiB SDRAM K9F1G08
- 4MiB spi flash
- ethernet DM9161CEP
- UART2 console

---
 board/loongson/ls1c300-eval/Kconfig     | 12 ++++++
 board/loongson/ls1c300-eval/MAINTAINERS |  7 ++++
 board/loongson/ls1c300-eval/Makefile    |  3 ++
 board/loongson/ls1c300-eval/board.c     | 19 +++++++++
 configs/ls1c300_defconfig               | 52 +++++++++++++++++++++++++
 include/configs/ls1c300.h               | 38 ++++++++++++++++++
 6 files changed, 131 insertions(+)
 create mode 100644 board/loongson/ls1c300-eval/Kconfig
 create mode 100644 board/loongson/ls1c300-eval/MAINTAINERS
 create mode 100644 board/loongson/ls1c300-eval/Makefile
 create mode 100644 board/loongson/ls1c300-eval/board.c
 create mode 100644 configs/ls1c300_defconfig
 create mode 100644 include/configs/ls1c300.h
board/loongson/ls1c300-eval/Kconfig new file +12 -0
new file mode 100644
index 00000000000..e427570a836
@@ -0,0 +1,12 @@
+if BOARD_LS1C300
+
+config SYS_BOARD
+	default "ls1c300-eval"
+
+config SYS_VENDOR
+	default "loongson"
+
+config SYS_CONFIG_NAME
+	default "ls1c300"
+
+endif
board/loongson/ls1c300-eval/MAINTAINERS new file +7 -0
new file mode 100644
index 00000000000..d3498b18e2b
@@ -0,0 +1,7 @@
+LS1C300_EVAL BOARD
+M:	Du Huanpeng <[email protected]>
+S:	Maintained
+F:	board/loongson/ls1c300-eval/
+F:	include/configs/ls1c300.h
+F:	configs/ls1c300_defconfig
+F:	arch/mips/dts/ls1c300-eval.dts
board/loongson/ls1c300-eval/Makefile new file +3 -0
new file mode 100644
index 00000000000..db129c5abae
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-y += board.o
board/loongson/ls1c300-eval/board.c new file +19 -0
new file mode 100644
index 00000000000..0eb5df1dc7b
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020-2026 Du Huanpeng <[email protected]>
+ */
+
+#include <mach/serial.h>
+
+#if defined(CONFIG_DEBUG_UART_BOARD_INIT)
+
+#define UART2_RX	36
+#define UART2_TX	37
+#define AFUNC		2
+
+void board_debug_uart_init(void)
+{
+	gpio_set_alternate(UART2_TX, AFUNC);
+	gpio_set_alternate(UART2_RX, AFUNC);
+}
+#endif
configs/ls1c300_defconfig new file +52 -0

52 lines not on this page · raw message

include/configs/ls1c300.h new file +38 -0
new file mode 100644
index 00000000000..488d1c40330
@@ -0,0 +1,38 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2020 MediaTek Inc.
+ *
+ * Author: Gao Weijie <[email protected]>
+ * based on: include/configs/mt7628.h
+ * Copyright (C) 2022-2023 Du Huanpeng <[email protected]>
+ */
+
+#ifndef __CONFIG_LS1C300_H__
+#define __CONFIG_LS1C300_H__
+
+#define CFG_SYS_SDRAM_BASE		0x80200000
+#define CFG_SYS_INIT_SP_OFFSET		0x2000
+
+/* SPL */
+#if defined(CONFIG_SPL_BUILD)
+
+/* Serial SPL */
+#if defined(CONFIG_SPL_SERIAL)
+#define CFG_SYS_NS16550_CLK		66000000
+#define CFG_SYS_NS16550_COM1		0xbfe44000
+#define CFG_SYS_NS16550_COM2		0xbfe48000
+#define CFG_SYS_NS16550_COM3		0xbfe4c000
+#define CFG_SYS_NS16550_COM4		0xbfe4c400
+#define CFG_SYS_NS16550_COM5		0xbfe4c500
+#define CFG_SYS_NS16550_COM6		0xbfe4c600
+#endif
+
+#define CFG_MALLOC_F_ADDR		0x80100000	/* FIXME: find a proper place */
+#define CFG_SYS_UBOOT_BASE		0xbd000000
+
+#endif
+
+/* Serial common */
+#define CFG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 }
+
+#endif /* __CONFIG_LS1C300_H__ */
Signature · 1 line
2.43.0
#5 lore raw

PATCH v7 5/7 mips: loongson: add clk driver

In reply to [email protected]

From: Du Huanpeng <[email protected]>

clk driver loongson mips for embedded SoC ls1c300

---
 drivers/clk/Makefile               |   1 +
 drivers/clk/loongson/Makefile      |   3 +
 drivers/clk/loongson/clk-ls1c300.c | 186 +++++++++++++++++++++++++++++
 3 files changed, 190 insertions(+)
 create mode 100644 drivers/clk/loongson/Makefile
 create mode 100644 drivers/clk/loongson/clk-ls1c300.c
drivers/clk/Makefile +1 -0
index 5f0c0d8a5c2..e19bb17276e 100644
@@ -23,6 +23,7 @@ obj-y += ti/
 obj-$(CONFIG_CLK_THEAD) += thead/
 obj-$(CONFIG_$(PHASE_)CLK_INTEL) += intel/
 obj-$(CONFIG_ARCH_ASPEED) += aspeed/
+obj-$(CONFIG_ARCH_LSMIPS) += loongson/
 obj-$(CONFIG_ARCH_MEDIATEK) += mediatek/
 obj-$(CONFIG_ARCH_MESON) += meson/
 obj-$(CONFIG_ARCH_MTMIPS) += mtmips/
drivers/clk/loongson/Makefile new file +3 -0
new file mode 100644
index 00000000000..0a47269cd30
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-$(CONFIG_SOC_LS1C300) += clk-ls1c300.o
drivers/clk/loongson/clk-ls1c300.c new file +186 -0

186 lines not on this page · raw message

Signature · 1 line
2.43.0
#6 lore raw

PATCH v7 6/7 mips: loongson: add watchdog driver

In reply to [email protected]

From: Du Huanpeng <[email protected]>

supports watchdog in loongson mips embedded SoCs

---
 drivers/watchdog/Kconfig        |   8 ++
 drivers/watchdog/Makefile       |   1 +
 drivers/watchdog/loongson_wdt.c | 127 ++++++++++++++++++++++++++++++++
 3 files changed, 136 insertions(+)
 create mode 100644 drivers/watchdog/loongson_wdt.c
drivers/watchdog/Kconfig +8 -0
index 416d29d256a..beba5475e03 100644
@@ -214,6 +214,14 @@ config SPL_WDT_GPIO
 	help
 	  Support for external watchdog fed by toggling a gpio in SPL.
 
+config WDT_LOONGSON
+	bool "Loongson MIPS watchdog timer support"
+	depends on WDT
+	help
+	  Select this to enable watchdog timer for Loongson SoCs.
+	  The watchdog timer is stopped when initialized.
+	  It performs full SoC reset.
+
 config WDT_MAX6370
 	bool "MAX6370 watchdog timer support"
 	depends on WDT
drivers/watchdog/Makefile +1 -0
index 02e2674f8af..e9ffb417050 100644
@@ -33,6 +33,7 @@ obj-$(CONFIG_WDT_DA9063) += da9063-wdt.o
 obj-$(CONFIG_WDT_DAVINCI) += davinci_wdt.o
 obj-$(CONFIG_WDT_FTWDT010) += ftwdt010_wdt.o
 obj-$(CONFIG_$(SPL_TPL_)WDT_GPIO) += gpio_wdt.o
+obj-$(CONFIG_WDT_LOONGSON) += loongson_wdt.o
 obj-$(CONFIG_WDT_MAX6370) += max6370_wdt.o
 obj-$(CONFIG_WDT_MCF) += mcf_wdt.o
 obj-$(CONFIG_WDT_MESON_GXBB) += meson_gxbb_wdt.o
drivers/watchdog/loongson_wdt.c new file +127 -0

127 lines not on this page · raw message

Signature · 1 line
2.43.0
#7 lore raw

PATCH v7 7/7 mips: loongson: ls1c300 dts and bindings

In reply to [email protected]

From: Du Huanpeng <[email protected]>

- ls1c300 dtsi
- ls1c300-eval board dts
- clk binding header
- reset binding header

---
 arch/mips/dts/loongson32-ls1c300b.dtsi    | 151 ++++++++++++++++++++++
 arch/mips/dts/ls1c300-eval.dts            |  30 +++++
 include/dt-bindings/clock/ls1c300-clk.h   |  18 +++
 include/dt-bindings/reset/ls1c300-reset.h |  36 ++++++
 4 files changed, 235 insertions(+)
 create mode 100644 arch/mips/dts/loongson32-ls1c300b.dtsi
 create mode 100644 arch/mips/dts/ls1c300-eval.dts
 create mode 100644 include/dt-bindings/clock/ls1c300-clk.h
 create mode 100644 include/dt-bindings/reset/ls1c300-reset.h
arch/mips/dts/loongson32-ls1c300b.dtsi new file +151 -0
new file mode 100644
index 00000000000..26b0c707459
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/ls1c300-clk.h>
+#include <dt-bindings/reset/ls1c300-reset.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "loongson,ls1c300-soc";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@0 {
+			device_type = "cpu";
+			reg = <0>;
+			compatible = "loongson,gs232", "mips,mips4Kc";
+			clocks = <&acc CLK_CPU_THROT>;
+		};
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		bootph-all;
+
+
+		xtal: oscillator {
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+			#clock-cells = <0>;
+		};
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges;
+
+		acc: clock-controller@1fe78030 {
+			compatible = "loongson,ls1c300-clk";
+			clocks = <&xtal>;
+			#clock-cells = <1>;
+			reg = <0x1fe78030 0x8>, <0x1fe7c010 0x4>;
+			bootph-all;
+		};
+
+		uart0: serial@1fe40000 {
+			compatible = "loongson,ls1c300-uart", "ns16550a";
+			clocks = <&acc CLK_APB>;
+			reg = <0x1fe40000 0x100>;
+			status = "disabled";
+		};
+
+		uart1: serial@1fe44000 {
+			compatible = "loongson,ls1c300-uart", "ns16550a";
+			clocks = <&acc CLK_APB>;
+			reg = <0x1fe44000 0x100>;
+			status = "disabled";
+		};
+
+		uart2: serial@1fe48000 {
+			compatible = "loongson,ls1c300-uart", "ns16550a";
+			clocks = <&acc CLK_APB>;
+			reg = <0x1fe48000 0x100>;
+			resets = <&shut_ctrl UART2_SHUT>;
+			reset-names = "uart2";
+			status = "disabled";
+		};
+
+		uart3: serial@1fe4c000 {
+			compatible = "loongson,ls1c300-uart", "ns16550a";
+			clocks = <&acc CLK_APB>;
+			reg = <0x1fe4c000 0x100>;
+			status = "disabled";
+		};
+
+		uart4:  serial@1fe4c400 {
+			compatible = "loongson,ls1c300-uart", "ns16550a";
+			clocks = <&acc CLK_APB>;
+			reg = <0x1fe4c400 0x100>;
+			status = "disabled";
+		};
+
+		uart5:  serial@1fe4c500 {
+			compatible = "loongson,ls1c300-uart", "ns16550a";
+			clocks = <&acc CLK_APB>;
+			reg = <0x1fe4c500 0x100>;
+			status = "disabled";
+		};
+
+		uart6:  serial@1fe4c600 {
+			compatible = "loongson,ls1c300-uart", "ns16550a";
+			clocks = <&acc CLK_APB>;
+			reg = <0x1fe4c600 0x100>;
+			status = "disabled";
+		};
+
+		uart7:  serial@1fe4c700 {
+			compatible = "loongson,ls1c300-uart", "ns16550a";
+			clocks = <&acc CLK_APB>;
+			reg = <0x1fe4c700 0x100>;
+			status = "disabled";
+		};
+
+		uart8:  serial@1fe4c800 {
+			compatible = "loongson,ls1c300-uart", "ns16550a";
+			clocks = <&acc CLK_APB>;
+			reg = <0x1fe4c800 0x100>;
+			status = "disabled";
+		};
+
+		uart9:  serial@1fe4c900 {
+			compatible = "loongson,ls1c300-uart", "ns16550a";
+			clocks = <&acc CLK_APB>;
+			reg = <0x1fe4c900 0x100>;
+			status = "disabled";
+		};
+
+		uart10: serial@1fe4ca00 {
+			compatible = "loongson,ls1c300-uart", "ns16550a";
+			clocks = <&acc CLK_APB>;
+			reg = <0x1fe4ca00 0x100>;
+			status = "disabled";
+		};
+
+		uart11: serial@1fe4cb00 {
+			compatible = "loongson,ls1c300-uart", "ns16550a";
+			clocks = <&acc CLK_APB>;
+			reg = <0x1fe4cb00 0x100>;
+			status = "disabled";
+		};
+
+		wdt: watchdog@1fe5c060 {
+			compatible = "loongson,ls1c300-wdt";
+			clocks = <&acc CLK_APB>;
+			reg = <0x1fe5c060 0x10>;
+		};
+
+		reset-controller {
+			compatible = "wdt-reboot";
+			wdt = <&wdt>;
+		};
+
+		shut_ctrl: reset-controller@1fd00420 {
+			compatible = "loongson,shut_ctrl";
+			reg = <0x1fd00420 0x4>;
+			#reset-cells = <1>;
+		};
+	};
+};
arch/mips/dts/ls1c300-eval.dts new file +30 -0
new file mode 100644
index 00000000000..cc3c267a5bf
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Du Huanpeng <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "loongson32-ls1c300b.dtsi"
+
+/ {
+	compatible = "lsmips,ls1c300-soc";
+	model = "ls1c300-eval";
+
+	aliases {
+		serial0 = &uart2;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x4000000>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
include/dt-bindings/clock/ls1c300-clk.h new file +18 -0
new file mode 100644
index 00000000000..170728693be
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2022 Du Huanpeng <[email protected]>
+ */
+
+#ifndef __DT_BINDINGS_LS1C300_CLK_H__
+#define __DT_BINDINGS_LS1C300_CLK_H__
+
+#define CLK_XTAL	0
+#define CLK_PLL		1
+#define CLK_CPU		2
+#define CLK_APB		3
+#define CLK_CAMERA	4
+#define CLK_PIX		5
+#define CLK_AXIMUX	6
+#define CLK_CPU_THROT	7
+
+#endif /* __DT_BINDINGS_LS1C300_CLK_H__ */
include/dt-bindings/reset/ls1c300-reset.h new file +36 -0
new file mode 100644
index 00000000000..44734ee50a9
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2022 Du Huanpeng <[email protected]>
+ */
+
+#ifndef _DT_BINDINGS_LS1C300_RESET_H_
+#define _DT_BINDINGS_LS1C300_RESET_H_
+
+#define ADC_SHUT        25
+#define SDIO_SHUT       24
+#define DMA2_SHUT       23
+#define DMA1_SHUT       22
+#define DMA0_SHUT       21
+#define SPI1_SHUT       20
+#define SPI0_SHUT       19
+#define I2C2_SHUT       18
+#define I2C1_SHUT       17
+#define I2C0_SHUT       16
+#define AC97_SHUT       15
+#define I2S_SHUT        14
+#define UART3_SHUT      13
+#define UART2_SHUT      12
+#define UART1_SHUT      11
+#define UART0_SHUT      10
+#define CAN1_SHUT       9
+#define CAN0_SHUT       8
+#define ECC_SHUT        7
+#define MAC_SHUT        6
+#define USBHOST_SHUT    5
+#define USBOTG_SHUT     4
+#define SDRAM_SHUT      3
+#define SRAM_SHUT       2
+#define CAM_SHUT        1
+#define LCD_SHUT        0
+
+#endif  /* _DT_BINDINGS_LS1C300_RESET_H_*/
Signature · 1 line
2.43.0