Skip to contentSkip to conversation

drm: bridge: dw_hdmi: Misc enable/disable, CEC and EDID cleanup

PATCH Superseded Jonas Karlman 4 participants 32 messages Apr 3 – Apr 29

Subsystems (4)

v3 of 7 Superseded Latest is v7 →

lore
Share & tools
lore

Jonas Karlman

author reviewer
#0 lore raw

v3 cover drm: bridge: dw_hdmi: Misc enable/disable, CEC and EDID cleanup

This is a revival of an old dw-hdmi series and is the first series part of a new effort to upstream old LibreELEC HDMI 2.0 patches for Rockchip RK33xx devices.

This series ensure poweron/poweroff and CEC phys addr invalidation is happening under drm mode_config mutex lock, and also ensure EDID is updated after a HPD low voltage pulse by changing to debounce hotplug processing.

These changes have mainly been tested on Rockchip RK3328, RK3399 and RK3568 devices.

Rockchip uses the dw-hdmi connector, so this could use some more testing with drivers that use the bridge connector.

Future planned series will likely convert dw-hdmi to a hdmi bridge and add improved deep color support as preparation to add 10-bit and yuv420 output support on Rockchip RK33xx devices.

Testing with a Rock Pi 4 (RK3399) using a Reaspberry Pi Monitor with Linux kms client console using drm.debug=0xe should log something like following:

Power cycle monitor using the power button:
[CONNECTOR:68:HDMI-A-1] CEA VCDB 0x4a
[CONNECTOR:68:HDMI-A-1] HDMI: DVI dual 0, max TMDS clock 0 kHz [CONNECTOR:68:HDMI-A-1] ELD monitor RPI MON156
[CONNECTOR:68:HDMI-A-1] HDMI: latency present 0 0, video latency 0 0, audio latency 0 0 [CONNECTOR:68:HDMI-A-1] ELD size 36, SAD count 1
[CONNECTOR:68:HDMI-A-1] Same epoch counter 10

Cable unplugged:
[CONNECTOR:68:HDMI-A-1] EDID changed, epoch counter 11 [CONNECTOR:68:HDMI-A-1] status updated from connected to disconnected [CONNECTOR:68:HDMI-A-1] Changed epoch counter 10 => 12 [CONNECTOR:68:HDMI-A-1] generating connector hotplug event [CONNECTOR:68:HDMI-A-1] Sent hotplug event

Cable connected:
[CONNECTOR:68:HDMI-A-1] CEA VCDB 0x4a
[CONNECTOR:68:HDMI-A-1] HDMI: DVI dual 0, max TMDS clock 0 kHz [CONNECTOR:68:HDMI-A-1] ELD monitor RPI MON156
[CONNECTOR:68:HDMI-A-1] HDMI: latency present 0 0, video latency 0 0, audio latency 0 0 [CONNECTOR:68:HDMI-A-1] ELD size 36, SAD count 1
[CONNECTOR:68:HDMI-A-1] status updated from disconnected to connected [CONNECTOR:68:HDMI-A-1] Changed epoch counter 12 => 13 [CONNECTOR:68:HDMI-A-1] generating connector hotplug event [CONNECTOR:68:HDMI-A-1] Sent hotplug event

Changes in v3:
- Rework EDID refresh handling to closer match bridge connector
- Use delayed work to debounce HPD processing
- Update commit messages
- Collect r-b tags
- Rebased on next-20260401
Link to v2: https://lore.kernel.org/r/[email protected]/

Changes in v2:
- Add patch to disable scrambler feature when not supported
- Add patch to only notify connected status on HPD interrupt
- Update commit messages
- Collect r-b tags
- Rebased on next-20240906
Link to v1: https://lore.kernel.org/r/[email protected]/

Jonas Karlman (13):
drm: bridge: dw_hdmi: Disable scrambler feature when not supported
drm: bridge: dw_hdmi: Only notify connected status on HPD interrupt
drm: bridge: dw_hdmi: Call poweron/poweroff from atomic enable/disable
drm: bridge: dw_hdmi: Use passed mode instead of stored previous_mode
drm: bridge: dw_hdmi: Fold poweron and setup functions
drm: bridge: dw_hdmi: Remove previous_mode and mode_set
drm: bridge: dw_hdmi: Invalidate CEC phys addr from connector detect
drm: bridge: dw_hdmi: Remove cec_notifier_mutex
drm: bridge: dw_hdmi: Use delayed_work to debounce hotplug event
drm: bridge: dw_hdmi: Use drm_connector_helper_hpd_irq_event()
drm: bridge: dw_hdmi: Extract dw_hdmi_connector_status_update()
drm: bridge: dw_hdmi: Use dw_hdmi_connector_status_update()
drm: bridge: dw_hdmi: Use display_info is_hdmi and has_audio

 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 209 +++++++++-------------
 1 file changed, 80 insertions(+), 129 deletions(-)
Signature · 1 line
2.53.0
author reviewer
#1 lore raw

PATCH v3 1/13 drm: bridge: dw_hdmi: Disable scrambler feature when not supported

The scrambler feature can be left enabled when hotplugging from a sink and mode that require scrambling to a sink that does not support SCDC or scrambling.

Typically a blank screen or 'no signal' message can be observed after using a HDMI 2.0 4K@60Hz mode and then hotplugging to a sink that only support HDMI 1.4.

Fix this by disabling the scrambler feature when SCDC is not supported.

Fixes 264fce6cc2c1 ("drm/bridge: dw-hdmi: Add SCDC and TMDS Scrambling support")

---
v3: Collect r-b tag
v2: New patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +2 -0
index 0296e110ce65..9febcb58a1df 100644
@@ -2133,6 +2133,8 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi,
 				    HDMI_MC_SWRSTZ);
 			drm_scdc_set_scrambling(hdmi->curr_conn, 0);
 		}
+	} else if (hdmi->version >= 0x200a) {
+		hdmi_writeb(hdmi, 0, HDMI_FC_SCRAMBLER_CTRL);
 	}
 
 	/* Set up horizontal active pixel width */
Signature · 1 line
2.53.0
author reviewer
#2 lore raw

PATCH v3 2/13 drm: bridge: dw_hdmi: Only notify connected status on HPD interrupt

In reply to Jonas Karlman

drm_helper_hpd_irq_event() and drm_bridge_hpd_notify() may incorrectly be called with a connected status when HPD is high and RX sense is changed. This typically happens when the HDMI cable is unplugged, shortly before the HPD is changed to low.

The original intent of commit da09daf88108 ("drm: bridge: dw_hdmi: only trigger hotplug event on link change") was to signal hotplug event at correct interrupt states.

Based on the commit message the intent was to trigger hotplug event:
- when HPD goes high (plugin)
- when both HPD and RX sense has gone low (plugout)

However, following interrupt state changes can typically be observed when the HDMI cable is unplugged:
- RX interrupt: HPD=high RX=low -> triggers a connected event
- HPD interrupt: HPD=low RX=low -> triggers a disconnected event

Fix this by only notify connected status on the HPD interrupt when HPD is going high, not on the RX sense interrupt when RX sense is changed.

After this a connected event should be triggered when HPD=high at HPD interrupt, and a disconnected event should be triggered when both HPD=low and RX=low at either HPD or RX interrupt.

Fixes da09daf88108 ("drm: bridge: dw_hdmi: only trigger hotplug event on link change")

---
v3: Update commit message
v2: New patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +2 -1
index 9febcb58a1df..3b851f12adfe 100644
@@ -3140,7 +3140,8 @@ static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
 			mutex_unlock(&hdmi->cec_notifier_mutex);
 		}
 
-		if (phy_stat & HDMI_PHY_HPD)
+		if ((intr_stat & HDMI_IH_PHY_STAT0_HPD) &&
+		    (phy_stat & HDMI_PHY_HPD))
 			status = connector_status_connected;
 
 		if (!(phy_stat & (HDMI_PHY_HPD | HDMI_PHY_RX_SENSE)))
Signature · 1 line
2.53.0
Reviewed-by on v3 2/13
#3 lore raw

Re: [PATCH v3 02/13] drm: bridge: dw_hdmi: Only notify connected status on HPD interrupt

Quoted 40 lines · On Friday, 3 April 2026 20:52:48 Central European Summer Time Jonas Karlman…

drm_helper_hpd_irq_event() and drm_bridge_hpd_notify() may incorrectly be called with a connected status when HPD is high and RX sense is changed. This typically happens when the HDMI cable is unplugged, shortly before the HPD is changed to low.

The original intent of commit da09daf88108 ("drm: bridge: dw_hdmi: only trigger hotplug event on link change") was to signal hotplug event at correct interrupt states.

Based on the commit message the intent was to trigger hotplug event:
- when HPD goes high (plugin)
- when both HPD and RX sense has gone low (plugout)

However, following interrupt state changes can typically be observed when the HDMI cable is unplugged:
- RX interrupt: HPD=high RX=low -> triggers a connected event
- HPD interrupt: HPD=low RX=low -> triggers a disconnected event

Fix this by only notify connected status on the HPD interrupt when HPD is going high, not on the RX sense interrupt when RX sense is changed.

After this a connected event should be triggered when HPD=high at HPD interrupt, and a disconnected event should be triggered when both HPD=low and RX=low at either HPD or RX interrupt.

Fixes da09daf88108 ("drm: bridge: dw_hdmi: only trigger hotplug event on link change")

---
v3: Update commit message
v2: New patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +0 -0
index 9febcb58a1df..3b851f12adfe 100644

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c static irqreturn_t dw_hdmi_irq(int irq, void *dev_id) · line 3147

Quoted 9 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +2 -1
@@ -3140,7 +3140,8 @@ static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
 			mutex_unlock(&hdmi->cec_notifier_mutex);
 		}
 
-		if (phy_stat & HDMI_PHY_HPD)
+		if ((intr_stat & HDMI_IH_PHY_STAT0_HPD) &&
+		    (phy_stat & HDMI_PHY_HPD))
 			status = connector_status_connected;
 
 		if (!(phy_stat & (HDMI_PHY_HPD | HDMI_PHY_RX_SENSE)))
author reviewer
#4 lore raw

PATCH v3 3/13 drm: bridge: dw_hdmi: Call poweron/poweroff from atomic enable/disable

In reply to Jonas Karlman

Change to only call poweron/poweroff from atomic_enable/atomic_disable funcs instead of trying to be clever by keeping a bridge_is_on state and poweron/off in the hotplug irq handler.

The bridge is already enabled/disabled depending on connection state with the call to drm_helper_hpd_irq_event() in hotplug irq handler.

A benefit of this is that drm mode_config mutex is always held at poweron/off, something that may reduce the need for the dw-hdmi mutex.

---
v3: Collect r-b tag
v2: Update commit message

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 33 ++---------------------
 1 file changed, 2 insertions(+), 31 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +2 -31
index 3b851f12adfe..eea266d01de3 100644
@@ -169,7 +169,6 @@ struct dw_hdmi {
 	enum drm_connector_force force;	/* mutex-protected force state */
 	struct drm_connector *curr_conn;/* current connector (only valid when !disabled) */
 	bool disabled;			/* DRM has disabled our bridge */
-	bool bridge_is_on;		/* indicates the bridge is on */
 	bool rxsense;			/* rxsense state */
 	u8 phy_mask;			/* desired phy int mask settings */
 	u8 mc_clkdis;			/* clock disable register */
@@ -2398,8 +2397,6 @@ static void initialize_hdmi_ih_mutes(struct dw_hdmi *hdmi)
 
 static void dw_hdmi_poweron(struct dw_hdmi *hdmi)
 {
-	hdmi->bridge_is_on = true;
-
 	/*
 	 * The curr_conn field is guaranteed to be valid here, as this function
 	 * is only be called when !hdmi->disabled.
@@ -2413,30 +2410,6 @@ static void dw_hdmi_poweroff(struct dw_hdmi *hdmi)
 		hdmi->phy.ops->disable(hdmi, hdmi->phy.data);
 		hdmi->phy.enabled = false;
 	}
-
-	hdmi->bridge_is_on = false;
-}
-
-static void dw_hdmi_update_power(struct dw_hdmi *hdmi)
-{
-	int force = hdmi->force;
-
-	if (hdmi->disabled) {
-		force = DRM_FORCE_OFF;
-	} else if (force == DRM_FORCE_UNSPECIFIED) {
-		if (hdmi->rxsense)
-			force = DRM_FORCE_ON;
-		else
-			force = DRM_FORCE_OFF;
-	}
-
-	if (force == DRM_FORCE_OFF) {
-		if (hdmi->bridge_is_on)
-			dw_hdmi_poweroff(hdmi);
-	} else {
-		if (!hdmi->bridge_is_on)
-			dw_hdmi_poweron(hdmi);
-	}
 }
 
 /*
@@ -2561,7 +2534,6 @@ static void dw_hdmi_connector_force(struct drm_connector *connector)
 
 	mutex_lock(&hdmi->mutex);
 	hdmi->force = connector->force;
-	dw_hdmi_update_power(hdmi);
 	dw_hdmi_update_phy_mask(hdmi);
 	mutex_unlock(&hdmi->mutex);
 }
@@ -2971,7 +2943,7 @@ static void dw_hdmi_bridge_atomic_disable(struct drm_bridge *bridge,
 	mutex_lock(&hdmi->mutex);
 	hdmi->disabled = true;
 	hdmi->curr_conn = NULL;
-	dw_hdmi_update_power(hdmi);
+	dw_hdmi_poweroff(hdmi);
 	dw_hdmi_update_phy_mask(hdmi);
 	handle_plugged_change(hdmi, false);
 	mutex_unlock(&hdmi->mutex);
@@ -2989,7 +2961,7 @@ static void dw_hdmi_bridge_atomic_enable(struct drm_bridge *bridge,
 	mutex_lock(&hdmi->mutex);
 	hdmi->disabled = false;
 	hdmi->curr_conn = connector;
-	dw_hdmi_update_power(hdmi);
+	dw_hdmi_poweron(hdmi);
 	dw_hdmi_update_phy_mask(hdmi);
 	handle_plugged_change(hdmi, true);
 	mutex_unlock(&hdmi->mutex);
@@ -3089,7 +3061,6 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense)
 		if (hpd)
 			hdmi->rxsense = true;
 
-		dw_hdmi_update_power(hdmi);
 		dw_hdmi_update_phy_mask(hdmi);
 	}
 	mutex_unlock(&hdmi->mutex);
Signature · 1 line
2.53.0
author reviewer
#5 lore raw

PATCH v3 4/13 drm: bridge: dw_hdmi: Use passed mode instead of stored previous_mode

In reply to Jonas Karlman

Use the passed mode instead of mixing use of passed mode and the stored previous_mode in dw_hdmi_setup(). The passed mode is currenly always the previous_mode.

Also fix a small typo and add a variable to help shorten a code line.

---
v3: Collect r-b tag
v2: Update commit message, s/type/typo/

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +4 -5
index eea266d01de3..c03a86284a95 100644
@@ -2256,6 +2256,7 @@ static int dw_hdmi_setup(struct dw_hdmi *hdmi,
 			 const struct drm_connector *connector,
 			 const struct drm_display_mode *mode)
 {
+	const struct drm_display_info *display = &connector->display_info;
 	int ret;
 
 	hdmi_disable_overflow_interrupts(hdmi);
@@ -2301,12 +2302,10 @@ static int dw_hdmi_setup(struct dw_hdmi *hdmi,
 	hdmi->hdmi_data.video_mode.mdataenablepolarity = true;
 
 	/* HDMI Initialization Step B.1 */
-	hdmi_av_composer(hdmi, &connector->display_info, mode);
+	hdmi_av_composer(hdmi, display, mode);
 
-	/* HDMI Initializateion Step B.2 */
-	ret = hdmi->phy.ops->init(hdmi, hdmi->phy.data,
-				  &connector->display_info,
-				  &hdmi->previous_mode);
+	/* HDMI Initialization Step B.2 */
+	ret = hdmi->phy.ops->init(hdmi, hdmi->phy.data, display, mode);
 	if (ret)
 		return ret;
 	hdmi->phy.enabled = true;
Signature · 1 line
2.53.0
author reviewer
#6 lore raw

PATCH v3 5/13 drm: bridge: dw_hdmi: Fold poweron and setup functions

In reply to Jonas Karlman

Fold the poweron and setup functions into one function and use the adjusted_mode directly from the new crtc_state to remove the need of storing previous_mode.

---
v3: Collect r-b tag
v2: No change

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 21 ++++++++-------------
 1 file changed, 8 insertions(+), 13 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +8 -13
index c03a86284a95..7e7147b14614 100644
@@ -2252,9 +2252,9 @@ static void hdmi_disable_overflow_interrupts(struct dw_hdmi *hdmi)
 		    HDMI_IH_MUTE_FC_STAT2);
 }
 
-static int dw_hdmi_setup(struct dw_hdmi *hdmi,
-			 const struct drm_connector *connector,
-			 const struct drm_display_mode *mode)
+static int dw_hdmi_poweron(struct dw_hdmi *hdmi,
+			   const struct drm_connector *connector,
+			   const struct drm_display_mode *mode)
 {
 	const struct drm_display_info *display = &connector->display_info;
 	int ret;
@@ -2394,15 +2394,6 @@ static void initialize_hdmi_ih_mutes(struct dw_hdmi *hdmi)
 	hdmi_writeb(hdmi, ih_mute, HDMI_IH_MUTE);
 }
 
-static void dw_hdmi_poweron(struct dw_hdmi *hdmi)
-{
-	/*
-	 * The curr_conn field is guaranteed to be valid here, as this function
-	 * is only be called when !hdmi->disabled.
-	 */
-	dw_hdmi_setup(hdmi, hdmi->curr_conn, &hdmi->previous_mode);
-}
-
 static void dw_hdmi_poweroff(struct dw_hdmi *hdmi)
 {
 	if (hdmi->phy.enabled) {
@@ -2952,15 +2943,19 @@ static void dw_hdmi_bridge_atomic_enable(struct drm_bridge *bridge,
 					 struct drm_atomic_state *state)
 {
 	struct dw_hdmi *hdmi = bridge->driver_private;
+	const struct drm_display_mode *mode;
 	struct drm_connector *connector;
+	struct drm_crtc *crtc;
 
 	connector = drm_atomic_get_new_connector_for_encoder(state,
 							     bridge->encoder);
+	crtc = drm_atomic_get_new_connector_state(state, connector)->crtc;
+	mode = &drm_atomic_get_new_crtc_state(state, crtc)->adjusted_mode;
 
 	mutex_lock(&hdmi->mutex);
 	hdmi->disabled = false;
 	hdmi->curr_conn = connector;
-	dw_hdmi_poweron(hdmi);
+	dw_hdmi_poweron(hdmi, connector, mode);
 	dw_hdmi_update_phy_mask(hdmi);
 	handle_plugged_change(hdmi, true);
 	mutex_unlock(&hdmi->mutex);
Signature · 1 line
2.53.0
author reviewer
#7 lore raw

PATCH v3 6/13 drm: bridge: dw_hdmi: Remove previous_mode and mode_set

In reply to Jonas Karlman

With the use of adjusted_mode directly from the crtc_state there is no longer a need to store a copy in previous_mode, remove it and the now unneeded mode_set ops.

---
v3: Collect r-b tag
v2: No change

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 19 +------------------
 1 file changed, 1 insertion(+), 18 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +1 -18
index 7e7147b14614..aa4949de9173 100644
@@ -154,8 +154,6 @@ struct dw_hdmi {
 		bool enabled;
 	} phy;
 
-	struct drm_display_mode previous_mode;
-
 	struct i2c_adapter *ddc;
 	void __iomem *regs;
 	bool sink_is_hdmi;
@@ -165,7 +163,7 @@ struct dw_hdmi {
 	struct pinctrl_state *default_state;
 	struct pinctrl_state *unwedge_state;
 
-	struct mutex mutex;		/* for state below and previous_mode */
+	struct mutex mutex;		/* for state below */
 	enum drm_connector_force force;	/* mutex-protected force state */
 	struct drm_connector *curr_conn;/* current connector (only valid when !disabled) */
 	bool disabled;			/* DRM has disabled our bridge */
@@ -2911,20 +2909,6 @@ dw_hdmi_bridge_mode_valid(struct drm_bridge *bridge,
 	return mode_status;
 }
 
-static void dw_hdmi_bridge_mode_set(struct drm_bridge *bridge,
-				    const struct drm_display_mode *orig_mode,
-				    const struct drm_display_mode *mode)
-{
-	struct dw_hdmi *hdmi = bridge->driver_private;
-
-	mutex_lock(&hdmi->mutex);
-
-	/* Store the display mode for plugin/DKMS poweron events */
-	drm_mode_copy(&hdmi->previous_mode, mode);
-
-	mutex_unlock(&hdmi->mutex);
-}
-
 static void dw_hdmi_bridge_atomic_disable(struct drm_bridge *bridge,
 					  struct drm_atomic_state *state)
 {
@@ -2988,7 +2972,6 @@ static const struct drm_bridge_funcs dw_hdmi_bridge_funcs = {
 	.atomic_get_input_bus_fmts = dw_hdmi_bridge_atomic_get_input_bus_fmts,
 	.atomic_enable = dw_hdmi_bridge_atomic_enable,
 	.atomic_disable = dw_hdmi_bridge_atomic_disable,
-	.mode_set = dw_hdmi_bridge_mode_set,
 	.mode_valid = dw_hdmi_bridge_mode_valid,
 	.detect = dw_hdmi_bridge_detect,
 	.edid_read = dw_hdmi_bridge_edid_read,
Signature · 1 line
2.53.0
author reviewer
#8 lore raw

PATCH v3 7/13 drm: bridge: dw_hdmi: Invalidate CEC phys addr from connector detect

In reply to Jonas Karlman

Wait until the connector detect ops is called to invalidate CEC phys addr instead of doing it directly from the irq handler.

---
v3: No change
v2: Collect r-b tag

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 18 +++++++++++-------
 1 file changed, 11 insertions(+), 7 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +11 -7
index aa4949de9173..975edd6e695a 100644
@@ -2470,7 +2470,17 @@ dw_hdmi_connector_detect(struct drm_connector *connector, bool force)
 {
 	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi,
 					     connector);
-	return dw_hdmi_detect(hdmi);
+	enum drm_connector_status status;
+
+	status = dw_hdmi_detect(hdmi);
+
+	if (status == connector_status_disconnected) {
+		mutex_lock(&hdmi->cec_notifier_mutex);
+		cec_notifier_phys_addr_invalidate(hdmi->cec_notifier);
+		mutex_unlock(&hdmi->cec_notifier_mutex);
+	}
+
+	return status;
 }
 
 static int dw_hdmi_connector_get_modes(struct drm_connector *connector)
@@ -3082,12 +3092,6 @@ static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
 				       phy_stat & HDMI_PHY_HPD,
 				       phy_stat & HDMI_PHY_RX_SENSE);
 
-		if ((phy_stat & (HDMI_PHY_RX_SENSE | HDMI_PHY_HPD)) == 0) {
-			mutex_lock(&hdmi->cec_notifier_mutex);
-			cec_notifier_phys_addr_invalidate(hdmi->cec_notifier);
-			mutex_unlock(&hdmi->cec_notifier_mutex);
-		}
-
 		if ((intr_stat & HDMI_IH_PHY_STAT0_HPD) &&
 		    (phy_stat & HDMI_PHY_HPD))
 			status = connector_status_connected;
Signature · 1 line
2.53.0
author reviewer
#9 lore raw

PATCH v3 8/13 drm: bridge: dw_hdmi: Remove cec_notifier_mutex

In reply to Jonas Karlman

With CEC phys addr invalidation moved away from the irq handler there is no longer a need for cec_notifier_mutex, remove it.

---
v3: No change
v2: Collect r-b tag

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 11 +----------
 1 file changed, 1 insertion(+), 10 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +1 -10
index 975edd6e695a..f3f8144ae98e 100644
@@ -187,7 +187,6 @@ struct dw_hdmi {
 	void (*enable_audio)(struct dw_hdmi *hdmi);
 	void (*disable_audio)(struct dw_hdmi *hdmi);
 
-	struct mutex cec_notifier_mutex;
 	struct cec_notifier *cec_notifier;
 
 	hdmi_codec_plugged_cb plugged_cb;
@@ -2474,11 +2473,8 @@ dw_hdmi_connector_detect(struct drm_connector *connector, bool force)
 
 	status = dw_hdmi_detect(hdmi);
 
-	if (status == connector_status_disconnected) {
-		mutex_lock(&hdmi->cec_notifier_mutex);
+	if (status == connector_status_disconnected)
 		cec_notifier_phys_addr_invalidate(hdmi->cec_notifier);
-		mutex_unlock(&hdmi->cec_notifier_mutex);
-	}
 
 	return status;
 }
@@ -2592,9 +2588,7 @@ static int dw_hdmi_connector_create(struct dw_hdmi *hdmi)
 	if (!notifier)
 		return -ENOMEM;
 
-	mutex_lock(&hdmi->cec_notifier_mutex);
 	hdmi->cec_notifier = notifier;
-	mutex_unlock(&hdmi->cec_notifier_mutex);
 
 	return 0;
 }
@@ -2893,10 +2887,8 @@ static void dw_hdmi_bridge_detach(struct drm_bridge *bridge)
 {
 	struct dw_hdmi *hdmi = bridge->driver_private;
 
-	mutex_lock(&hdmi->cec_notifier_mutex);
 	cec_notifier_conn_unregister(hdmi->cec_notifier);
 	hdmi->cec_notifier = NULL;
-	mutex_unlock(&hdmi->cec_notifier_mutex);
 }
 
 static enum drm_mode_status
@@ -3321,7 +3313,6 @@ struct dw_hdmi *dw_hdmi_probe(struct platform_device *pdev,
 
 	mutex_init(&hdmi->mutex);
 	mutex_init(&hdmi->audio_mutex);
-	mutex_init(&hdmi->cec_notifier_mutex);
 	spin_lock_init(&hdmi->audio_lock);
 
 	ret = dw_hdmi_parse_dt(hdmi);
Signature · 1 line
2.53.0
author reviewer
#10 lore raw

PATCH v3 9/13 drm: bridge: dw_hdmi: Use delayed_work to debounce hotplug event

In reply to Jonas Karlman

HDMI Specification Version 1.4b chapter 8.5 mentions:

An HDMI Sink shall not assert high voltage level on its Hot Plug Detect pin when the E-EDID is not available for reading.

A Source may use a high voltage level Hot Plug Detect signal to initiate the reading of E-EDID data.

An HDMI Sink shall indicate any change to the contents of the E-EDID by driving a low voltage level pulse on the Hot Plug Detect pin. This pulse shall be at least 100 msec.

Use a work queue to debounce reacting on HPD events to better handle a HPD low voltage level pulse when a sink changes the EDID.

The 1100 msec hotplug debounce timeout was arbitrarily picked to match other drivers using same const, and testing using a Raspberry Pi Monitor seem to use a 200-300 msec pulse when going from standby to power on state.

---
v3: New patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 24 +++++++++++++++++++----
 1 file changed, 20 insertions(+), 4 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +20 -4
index f3f8144ae98e..4d079b689b3b 100644
@@ -51,6 +51,8 @@
 
 #define HDMI14_MAX_TMDSCLK	340000000
 
+#define HOTPLUG_DEBOUNCE_MS	1100
+
 static const u16 csc_coeff_default[3][4] = {
 	{ 0x2000, 0x0000, 0x0000, 0x0000 },
 	{ 0x0000, 0x2000, 0x0000, 0x0000 },
@@ -192,6 +194,7 @@ struct dw_hdmi {
 	hdmi_codec_plugged_cb plugged_cb;
 	struct device *codec_dev;
 	enum drm_connector_status last_connector_result;
+	struct delayed_work hpd_work;
 };
 
 const struct dw_hdmi_plat_data *dw_hdmi_to_plat_data(struct dw_hdmi *hdmi)
@@ -2528,6 +2531,7 @@ static void dw_hdmi_connector_force(struct drm_connector *connector)
 
 	mutex_lock(&hdmi->mutex);
 	hdmi->force = connector->force;
+	hdmi->last_connector_result = connector->status;
 	dw_hdmi_update_phy_mask(hdmi);
 	mutex_unlock(&hdmi->mutex);
 }
@@ -3046,6 +3050,16 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense)
 }
 EXPORT_SYMBOL_GPL(dw_hdmi_setup_rx_sense);
 
+static void dw_hdmi_hpd_work(struct work_struct *work)
+{
+	struct dw_hdmi *hdmi = container_of(work, struct dw_hdmi, hpd_work.work);
+
+	if (hdmi->bridge.dev) {
+		drm_helper_hpd_irq_event(hdmi->bridge.dev);
+		drm_bridge_hpd_notify(&hdmi->bridge, hdmi->last_connector_result);
+	}
+}
+
 static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
 {
 	struct dw_hdmi *hdmi = dev_id;
@@ -3097,10 +3111,8 @@ static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
 			status == connector_status_connected ?
 			"plugin" : "plugout");
 
-		if (hdmi->bridge.dev) {
-			drm_helper_hpd_irq_event(hdmi->bridge.dev);
-			drm_bridge_hpd_notify(&hdmi->bridge, status);
-		}
+		mod_delayed_work(system_percpu_wq, &hdmi->hpd_work,
+				 msecs_to_jiffies(HOTPLUG_DEBOUNCE_MS));
 	}
 
 	hdmi_writeb(hdmi, intr_stat, HDMI_IH_PHY_STAT0);
@@ -3420,6 +3432,8 @@ struct dw_hdmi *dw_hdmi_probe(struct platform_device *pdev,
 		goto err_res;
 	}
 
+	INIT_DELAYED_WORK(&hdmi->hpd_work, dw_hdmi_hpd_work);
+
 	ret = devm_request_threaded_irq(dev, irq, dw_hdmi_hardirq,
 					dw_hdmi_irq, IRQF_SHARED,
 					dev_name(dev), hdmi);
@@ -3552,6 +3566,8 @@ EXPORT_SYMBOL_GPL(dw_hdmi_probe);
 
 void dw_hdmi_remove(struct dw_hdmi *hdmi)
 {
+	disable_delayed_work_sync(&hdmi->hpd_work);
+
 	drm_bridge_remove(&hdmi->bridge);
 
 	if (hdmi->audio && !IS_ERR(hdmi->audio))
Signature · 1 line
2.53.0
#11 lore raw

Re: [PATCH v3 09/13] drm: bridge: dw_hdmi: Use delayed_work to debounce hotplug event

Quoted 57 lines · On Friday, 3 April 2026 20:52:55 Central European Summer Time Jonas Karlman…

HDMI Specification Version 1.4b chapter 8.5 mentions:

An HDMI Sink shall not assert high voltage level on its Hot Plug Detect pin when the E-EDID is not available for reading.

A Source may use a high voltage level Hot Plug Detect signal to initiate the reading of E-EDID data.

An HDMI Sink shall indicate any change to the contents of the E-EDID by driving a low voltage level pulse on the Hot Plug Detect pin. This pulse shall be at least 100 msec.

Use a work queue to debounce reacting on HPD events to better handle a HPD low voltage level pulse when a sink changes the EDID.

The 1100 msec hotplug debounce timeout was arbitrarily picked to match other drivers using same const, and testing using a Raspberry Pi Monitor seem to use a 200-300 msec pulse when going from standby to power on state.

---
v3: New patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 24 +++++++++++++++++++----
 1 file changed, 20 insertions(+), 4 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +4 -0
index f3f8144ae98e..4d079b689b3b 100644
@@ -51,6 +51,8 @@
 
 #define HDMI14_MAX_TMDSCLK	340000000
 
+#define HOTPLUG_DEBOUNCE_MS	1100
+
 static const u16 csc_coeff_default[3][4] = {
 	{ 0x2000, 0x0000, 0x0000, 0x0000 },
 	{ 0x0000, 0x2000, 0x0000, 0x0000 },
@@ -192,6 +194,7 @@ struct dw_hdmi {
 	hdmi_codec_plugged_cb plugged_cb;
 	struct device *codec_dev;
 	enum drm_connector_status last_connector_result;
+	struct delayed_work hpd_work;
 };
 
 const struct dw_hdmi_plat_data *dw_hdmi_to_plat_data(struct dw_hdmi *hdmi)
@@ -2528,6 +2531,7 @@ static void dw_hdmi_connector_force(struct drm_connector *connector)
 
 	mutex_lock(&hdmi->mutex);
 	hdmi->force = connector->force;
+	hdmi->last_connector_result = connector->status;
 	dw_hdmi_update_phy_mask(hdmi);
 	mutex_unlock(&hdmi->mutex);
 }

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense) · line 3059

Quoted 10 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +7 -0
@@ -3046,6 +3050,16 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense)
 }
 EXPORT_SYMBOL_GPL(dw_hdmi_setup_rx_sense);
 
+static void dw_hdmi_hpd_work(struct work_struct *work)
+{
+	struct dw_hdmi *hdmi = container_of(work, struct dw_hdmi, hpd_work.work);
+
+	if (hdmi->bridge.dev) {
+		drm_helper_hpd_irq_event(hdmi->bridge.dev);
+		drm_bridge_hpd_notify(&hdmi->bridge, hdmi->last_connector_result);

I think you'll want to mutex_lock(&hdmi->mutex); (or better yet, guard(mutex)(&hdmi->mutex) or scoped_guard(mutex, &hdmi->mutex) {) here before reading last_connector_result, otherwise you'll have a data race with any writers.

Quoted 30 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +7 -4
+	}
+}
+
 static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
 {
 	struct dw_hdmi *hdmi = dev_id;
@@ -3097,10 +3111,8 @@ static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
 			status == connector_status_connected ?
 			"plugin" : "plugout");
 
-		if (hdmi->bridge.dev) {
-			drm_helper_hpd_irq_event(hdmi->bridge.dev);
-			drm_bridge_hpd_notify(&hdmi->bridge, status);
-		}
+		mod_delayed_work(system_percpu_wq, &hdmi->hpd_work,
+				 msecs_to_jiffies(HOTPLUG_DEBOUNCE_MS));
 	}
 
 	hdmi_writeb(hdmi, intr_stat, HDMI_IH_PHY_STAT0);
@@ -3420,6 +3432,8 @@ struct dw_hdmi *dw_hdmi_probe(struct platform_device *pdev,
 		goto err_res;
 	}
 
+	INIT_DELAYED_WORK(&hdmi->hpd_work, dw_hdmi_hpd_work);
+
 	ret = devm_request_threaded_irq(dev, irq, dw_hdmi_hardirq,
 					dw_hdmi_irq, IRQF_SHARED,
 					dev_name(dev), hdmi);

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c EXPORT_SYMBOL_GPL(dw_hdmi_probe); · line 3573

Quoted 8 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +2 -0
@@ -3552,6 +3566,8 @@ EXPORT_SYMBOL_GPL(dw_hdmi_probe);
 
 void dw_hdmi_remove(struct dw_hdmi *hdmi)
 {
+	disable_delayed_work_sync(&hdmi->hpd_work);
+
 	drm_bridge_remove(&hdmi->bridge);
 
 	if (hdmi->audio && !IS_ERR(hdmi->audio))

Kind regards,
Nicolas Frattaroli

author reviewer
#12 lore raw

Re: [PATCH v3 09/13] drm: bridge: dw_hdmi: Use delayed_work to debounce hotplug event

Hi Nicolas,

Quoted 61 lines · Nicolas Frattaroli
Quoted 60 lines · On Friday, 3 April 2026 20:52:55 Central European Summer Time Jonas Karlman…

HDMI Specification Version 1.4b chapter 8.5 mentions:

An HDMI Sink shall not assert high voltage level on its Hot Plug Detect pin when the E-EDID is not available for reading.

A Source may use a high voltage level Hot Plug Detect signal to initiate the reading of E-EDID data.

An HDMI Sink shall indicate any change to the contents of the E-EDID by driving a low voltage level pulse on the Hot Plug Detect pin. This pulse shall be at least 100 msec.

Use a work queue to debounce reacting on HPD events to better handle a HPD low voltage level pulse when a sink changes the EDID.

The 1100 msec hotplug debounce timeout was arbitrarily picked to match other drivers using same const, and testing using a Raspberry Pi Monitor seem to use a 200-300 msec pulse when going from standby to power on state.

---
v3: New patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 24 +++++++++++++++++++----
 1 file changed, 20 insertions(+), 4 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +4 -0
index f3f8144ae98e..4d079b689b3b 100644
@@ -51,6 +51,8 @@
 
 #define HDMI14_MAX_TMDSCLK	340000000
 
+#define HOTPLUG_DEBOUNCE_MS	1100
+
 static const u16 csc_coeff_default[3][4] = {
 	{ 0x2000, 0x0000, 0x0000, 0x0000 },
 	{ 0x0000, 0x2000, 0x0000, 0x0000 },
@@ -192,6 +194,7 @@ struct dw_hdmi {
 	hdmi_codec_plugged_cb plugged_cb;
 	struct device *codec_dev;
 	enum drm_connector_status last_connector_result;
+	struct delayed_work hpd_work;
 };
 
 const struct dw_hdmi_plat_data *dw_hdmi_to_plat_data(struct dw_hdmi *hdmi)
@@ -2528,6 +2531,7 @@ static void dw_hdmi_connector_force(struct drm_connector *connector)
 
 	mutex_lock(&hdmi->mutex);
 	hdmi->force = connector->force;
+	hdmi->last_connector_result = connector->status;
 	dw_hdmi_update_phy_mask(hdmi);
 	mutex_unlock(&hdmi->mutex);
 }
@@ -3046,6 +3050,16 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense)
 }
 EXPORT_SYMBOL_GPL(dw_hdmi_setup_rx_sense);
 
Quoted 12 lines

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense) · line 3059

Quoted 7 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +7 -0
+static void dw_hdmi_hpd_work(struct work_struct *work)
+{
+	struct dw_hdmi *hdmi = container_of(work, struct dw_hdmi, hpd_work.work);
+
+	if (hdmi->bridge.dev) {
+		drm_helper_hpd_irq_event(hdmi->bridge.dev);
+		drm_bridge_hpd_notify(&hdmi->bridge, hdmi->last_connector_result);

I think you'll want to mutex_lock(&hdmi->mutex); (or better yet, guard(mutex)(&hdmi->mutex) or scoped_guard(mutex, &hdmi->mutex) {) here before reading last_connector_result, otherwise you'll have a data race with any writers.

Thanks, I will adjust to something like that in a v4.

With the first call to drm_helper_hpd_irq_event() the dw_hdmi_detect() that updates the last_connector_result value should have been called. So by the time drm_bridge_hpd_notify() is called we should have the latest connector->status value in last_connector_result.

Ideally I would like to fully drop the drm_bridge_hpd_notify() call here and instead only call drm_connector_helper_hpd_irq_event() to detect any connector changes due to HPD and/or EDID changes. Something to look closer at in a future series :-)

Regards,
Jonas

Quoted 44 lines
Quoted 31 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +7 -4
+	}
+}
+
 static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
 {
 	struct dw_hdmi *hdmi = dev_id;
@@ -3097,10 +3111,8 @@ static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
 			status == connector_status_connected ?
 			"plugin" : "plugout");
 
-		if (hdmi->bridge.dev) {
-			drm_helper_hpd_irq_event(hdmi->bridge.dev);
-			drm_bridge_hpd_notify(&hdmi->bridge, status);
-		}
+		mod_delayed_work(system_percpu_wq, &hdmi->hpd_work,
+				 msecs_to_jiffies(HOTPLUG_DEBOUNCE_MS));
 	}
 
 	hdmi_writeb(hdmi, intr_stat, HDMI_IH_PHY_STAT0);
@@ -3420,6 +3432,8 @@ struct dw_hdmi *dw_hdmi_probe(struct platform_device *pdev,
 		goto err_res;
 	}
 
+	INIT_DELAYED_WORK(&hdmi->hpd_work, dw_hdmi_hpd_work);
+
 	ret = devm_request_threaded_irq(dev, irq, dw_hdmi_hardirq,
 					dw_hdmi_irq, IRQF_SHARED,
 					dev_name(dev), hdmi);

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c EXPORT_SYMBOL_GPL(dw_hdmi_probe); · line 3573

Quoted 8 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +2 -0
@@ -3552,6 +3566,8 @@ EXPORT_SYMBOL_GPL(dw_hdmi_probe);
 
 void dw_hdmi_remove(struct dw_hdmi *hdmi)
 {
+	disable_delayed_work_sync(&hdmi->hpd_work);
+
 	drm_bridge_remove(&hdmi->bridge);
 
 	if (hdmi->audio && !IS_ERR(hdmi->audio))

Kind regards,
Nicolas Frattaroli

#13 lore raw

Re: [PATCH v3 09/13] drm: bridge: dw_hdmi: Use delayed_work to debounce hotplug event

In reply to Jonas Karlman
Quoted 57 lines · Jonas Karlman

HDMI Specification Version 1.4b chapter 8.5 mentions:

An HDMI Sink shall not assert high voltage level on its Hot Plug Detect pin when the E-EDID is not available for reading.

A Source may use a high voltage level Hot Plug Detect signal to initiate the reading of E-EDID data.

An HDMI Sink shall indicate any change to the contents of the E-EDID by driving a low voltage level pulse on the Hot Plug Detect pin. This pulse shall be at least 100 msec.

Use a work queue to debounce reacting on HPD events to better handle a HPD low voltage level pulse when a sink changes the EDID.

The 1100 msec hotplug debounce timeout was arbitrarily picked to match other drivers using same const, and testing using a Raspberry Pi Monitor seem to use a 200-300 msec pulse when going from standby to power on state.

---
v3: New patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 24 +++++++++++++++++++----
 1 file changed, 20 insertions(+), 4 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +4 -0
index f3f8144ae98e..4d079b689b3b 100644
@@ -51,6 +51,8 @@
 
 #define HDMI14_MAX_TMDSCLK	340000000
 
+#define HOTPLUG_DEBOUNCE_MS	1100
+
 static const u16 csc_coeff_default[3][4] = {
 	{ 0x2000, 0x0000, 0x0000, 0x0000 },
 	{ 0x0000, 0x2000, 0x0000, 0x0000 },
@@ -192,6 +194,7 @@ struct dw_hdmi {
 	hdmi_codec_plugged_cb plugged_cb;
 	struct device *codec_dev;
 	enum drm_connector_status last_connector_result;
+	struct delayed_work hpd_work;
 };
 
 const struct dw_hdmi_plat_data *dw_hdmi_to_plat_data(struct dw_hdmi *hdmi)
@@ -2528,6 +2531,7 @@ static void dw_hdmi_connector_force(struct drm_connector *connector)
 
 	mutex_lock(&hdmi->mutex);
 	hdmi->force = connector->force;
+	hdmi->last_connector_result = connector->status;
 	dw_hdmi_update_phy_mask(hdmi);
 	mutex_unlock(&hdmi->mutex);
 }

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense) · line 3058

Quoted 9 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +6 -0
@@ -3046,6 +3050,16 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense)
 }
 EXPORT_SYMBOL_GPL(dw_hdmi_setup_rx_sense);
 
+static void dw_hdmi_hpd_work(struct work_struct *work)
+{
+	struct dw_hdmi *hdmi = container_of(work, struct dw_hdmi, hpd_work.work);
+
+	if (hdmi->bridge.dev) {
+		drm_helper_hpd_irq_event(hdmi->bridge.dev);

Nit: please consider this for the followup cleanup. The drm_helper_hpd_irq_event() is not very effective: we already know which bridge (and thus connector) caused the HPD event.

Moreover, the call should be redundant as drm_bridge_hpd_notify will call the registered callback, which normally would be drm_bridge_connector_hpd_cb(). Internally, this function calls drm_kms_helper_connector_hotplug_event().

Quoted 41 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +10 -4
+		drm_bridge_hpd_notify(&hdmi->bridge, hdmi->last_connector_result);
+	}
+}
+
 static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
 {
 	struct dw_hdmi *hdmi = dev_id;
@@ -3097,10 +3111,8 @@ static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
 			status == connector_status_connected ?
 			"plugin" : "plugout");
 
-		if (hdmi->bridge.dev) {
-			drm_helper_hpd_irq_event(hdmi->bridge.dev);
-			drm_bridge_hpd_notify(&hdmi->bridge, status);
-		}
+		mod_delayed_work(system_percpu_wq, &hdmi->hpd_work,
+				 msecs_to_jiffies(HOTPLUG_DEBOUNCE_MS));
 	}
 
 	hdmi_writeb(hdmi, intr_stat, HDMI_IH_PHY_STAT0);
@@ -3420,6 +3432,8 @@ struct dw_hdmi *dw_hdmi_probe(struct platform_device *pdev,
 		goto err_res;
 	}
 
+	INIT_DELAYED_WORK(&hdmi->hpd_work, dw_hdmi_hpd_work);
+
 	ret = devm_request_threaded_irq(dev, irq, dw_hdmi_hardirq,
 					dw_hdmi_irq, IRQF_SHARED,
 					dev_name(dev), hdmi);
@@ -3552,6 +3566,8 @@ EXPORT_SYMBOL_GPL(dw_hdmi_probe);
 
 void dw_hdmi_remove(struct dw_hdmi *hdmi)
 {
+	disable_delayed_work_sync(&hdmi->hpd_work);
+
 	drm_bridge_remove(&hdmi->bridge);
 
 	if (hdmi->audio && !IS_ERR(hdmi->audio))
Signature · 1 line
2.53.0
Signature · 2 lines
With best wishes
Dmitry
author reviewer
#14 lore raw

Re: [PATCH v3 09/13] drm: bridge: dw_hdmi: Use delayed_work to debounce hotplug event

Hi Dmitry,

Quoted 72 lines · Dmitry Baryshkov
Quoted 57 lines · Jonas Karlman

HDMI Specification Version 1.4b chapter 8.5 mentions:

An HDMI Sink shall not assert high voltage level on its Hot Plug Detect pin when the E-EDID is not available for reading.

A Source may use a high voltage level Hot Plug Detect signal to initiate the reading of E-EDID data.

An HDMI Sink shall indicate any change to the contents of the E-EDID by driving a low voltage level pulse on the Hot Plug Detect pin. This pulse shall be at least 100 msec.

Use a work queue to debounce reacting on HPD events to better handle a HPD low voltage level pulse when a sink changes the EDID.

The 1100 msec hotplug debounce timeout was arbitrarily picked to match other drivers using same const, and testing using a Raspberry Pi Monitor seem to use a 200-300 msec pulse when going from standby to power on state.

---
v3: New patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 24 +++++++++++++++++++----
 1 file changed, 20 insertions(+), 4 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +4 -0
index f3f8144ae98e..4d079b689b3b 100644
@@ -51,6 +51,8 @@
 
 #define HDMI14_MAX_TMDSCLK	340000000
 
+#define HOTPLUG_DEBOUNCE_MS	1100
+
 static const u16 csc_coeff_default[3][4] = {
 	{ 0x2000, 0x0000, 0x0000, 0x0000 },
 	{ 0x0000, 0x2000, 0x0000, 0x0000 },
@@ -192,6 +194,7 @@ struct dw_hdmi {
 	hdmi_codec_plugged_cb plugged_cb;
 	struct device *codec_dev;
 	enum drm_connector_status last_connector_result;
+	struct delayed_work hpd_work;
 };
 
 const struct dw_hdmi_plat_data *dw_hdmi_to_plat_data(struct dw_hdmi *hdmi)
@@ -2528,6 +2531,7 @@ static void dw_hdmi_connector_force(struct drm_connector *connector)
 
 	mutex_lock(&hdmi->mutex);
 	hdmi->force = connector->force;
+	hdmi->last_connector_result = connector->status;
 	dw_hdmi_update_phy_mask(hdmi);
 	mutex_unlock(&hdmi->mutex);
 }

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense) · line 3058

Quoted 9 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +6 -0
@@ -3046,6 +3050,16 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense)
 }
 EXPORT_SYMBOL_GPL(dw_hdmi_setup_rx_sense);
 
+static void dw_hdmi_hpd_work(struct work_struct *work)
+{
+	struct dw_hdmi *hdmi = container_of(work, struct dw_hdmi, hpd_work.work);
+
+	if (hdmi->bridge.dev) {
+		drm_helper_hpd_irq_event(hdmi->bridge.dev);

Nit: please consider this for the followup cleanup. The drm_helper_hpd_irq_event() is not very effective: we already know which bridge (and thus connector) caused the HPD event.

Quoted 4 lines

Moreover, the call should be redundant as drm_bridge_hpd_notify will call the registered callback, which normally would be drm_bridge_connector_hpd_cb(). Internally, this function calls drm_kms_helper_connector_hotplug_event().

I disagree in part, based on my testing, without a call to drm_helper_hpd_irq_event() or drm_connector_helper_hpd_irq_event() the internal check_connector_changed() never seem to be reached to detect any connector->status and/or connector->epoch_counter changes.

In my ongoing work to convert dw-hdmi to become a hdmi bridge, I have actually done the opposite to what you suggest here and instead fully dropped the call to drm_bridge_hpd_notify() made here.

drm_bridge_connector_detect() calls drm_bridge_connector_hpd_notify() so any bridges should already be notified as part of any internal check_connector_changed() handling.

Maybe something like following could be an option:

	changed = drm_connector_helper_hpd_irq_event(connector);
	if (changed)
		drm_bridge_hpd_notify(bridge, connector->status);

I will likely keep this as-is to keep existing behavior in a v4, as this patch was just about de-bouncing the existing calls being made at HPD.

Regards,
Jonas

Quoted 43 lines
Quoted 42 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +10 -4
+		drm_bridge_hpd_notify(&hdmi->bridge, hdmi->last_connector_result);
+	}
+}
+
 static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
 {
 	struct dw_hdmi *hdmi = dev_id;
@@ -3097,10 +3111,8 @@ static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
 			status == connector_status_connected ?
 			"plugin" : "plugout");
 
-		if (hdmi->bridge.dev) {
-			drm_helper_hpd_irq_event(hdmi->bridge.dev);
-			drm_bridge_hpd_notify(&hdmi->bridge, status);
-		}
+		mod_delayed_work(system_percpu_wq, &hdmi->hpd_work,
+				 msecs_to_jiffies(HOTPLUG_DEBOUNCE_MS));
 	}
 
 	hdmi_writeb(hdmi, intr_stat, HDMI_IH_PHY_STAT0);
@@ -3420,6 +3432,8 @@ struct dw_hdmi *dw_hdmi_probe(struct platform_device *pdev,
 		goto err_res;
 	}
 
+	INIT_DELAYED_WORK(&hdmi->hpd_work, dw_hdmi_hpd_work);
+
 	ret = devm_request_threaded_irq(dev, irq, dw_hdmi_hardirq,
 					dw_hdmi_irq, IRQF_SHARED,
 					dev_name(dev), hdmi);
@@ -3552,6 +3566,8 @@ EXPORT_SYMBOL_GPL(dw_hdmi_probe);
 
 void dw_hdmi_remove(struct dw_hdmi *hdmi)
 {
+	disable_delayed_work_sync(&hdmi->hpd_work);
+
 	drm_bridge_remove(&hdmi->bridge);
 
 	if (hdmi->audio && !IS_ERR(hdmi->audio))
Signature · 1 line
2.53.0
#15 lore raw

Re: [PATCH v3 09/13] drm: bridge: dw_hdmi: Use delayed_work to debounce hotplug event

Quoted 81 lines · Jonas Karlman

Hi Dmitry,

Quoted 72 lines · Dmitry Baryshkov
Quoted 57 lines · Jonas Karlman

HDMI Specification Version 1.4b chapter 8.5 mentions:

An HDMI Sink shall not assert high voltage level on its Hot Plug Detect pin when the E-EDID is not available for reading.

A Source may use a high voltage level Hot Plug Detect signal to initiate the reading of E-EDID data.

An HDMI Sink shall indicate any change to the contents of the E-EDID by driving a low voltage level pulse on the Hot Plug Detect pin. This pulse shall be at least 100 msec.

Use a work queue to debounce reacting on HPD events to better handle a HPD low voltage level pulse when a sink changes the EDID.

The 1100 msec hotplug debounce timeout was arbitrarily picked to match other drivers using same const, and testing using a Raspberry Pi Monitor seem to use a 200-300 msec pulse when going from standby to power on state.

---
v3: New patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 24 +++++++++++++++++++----
 1 file changed, 20 insertions(+), 4 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +4 -0
index f3f8144ae98e..4d079b689b3b 100644
@@ -51,6 +51,8 @@
 
 #define HDMI14_MAX_TMDSCLK  340000000
 
+#define HOTPLUG_DEBOUNCE_MS 1100
+
 static const u16 csc_coeff_default[3][4] = {
     { 0x2000, 0x0000, 0x0000, 0x0000 },
     { 0x0000, 0x2000, 0x0000, 0x0000 },
@@ -192,6 +194,7 @@ struct dw_hdmi {
     hdmi_codec_plugged_cb plugged_cb;
     struct device *codec_dev;
     enum drm_connector_status last_connector_result;
+    struct delayed_work hpd_work;
 };
 
 const struct dw_hdmi_plat_data *dw_hdmi_to_plat_data(struct dw_hdmi *hdmi)
@@ -2528,6 +2531,7 @@ static void dw_hdmi_connector_force(struct drm_connector *connector)
 
     mutex_lock(&hdmi->mutex);
     hdmi->force = connector->force;
+    hdmi->last_connector_result = connector->status;
     dw_hdmi_update_phy_mask(hdmi);
     mutex_unlock(&hdmi->mutex);
 }

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense) · line 3058

Quoted 9 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +6 -0
@@ -3046,6 +3050,16 @@ void dw_hdmi_setup_rx_sense(struct dw_hdmi *hdmi, bool hpd, bool rx_sense)
 }
 EXPORT_SYMBOL_GPL(dw_hdmi_setup_rx_sense);
 
+static void dw_hdmi_hpd_work(struct work_struct *work)
+{
+    struct dw_hdmi *hdmi = container_of(work, struct dw_hdmi, hpd_work.work);
+
+    if (hdmi->bridge.dev) {
+            drm_helper_hpd_irq_event(hdmi->bridge.dev);

Nit: please consider this for the followup cleanup. The drm_helper_hpd_irq_event() is not very effective: we already know which bridge (and thus connector) caused the HPD event.

Quoted 4 lines

Moreover, the call should be redundant as drm_bridge_hpd_notify will call the registered callback, which normally would be drm_bridge_connector_hpd_cb(). Internally, this function calls drm_kms_helper_connector_hotplug_event().

Quoted 8 lines

I disagree in part, based on my testing, without a call to drm_helper_hpd_irq_event() or drm_connector_helper_hpd_irq_event() the internal check_connector_changed() never seem to be reached to detect any connector->status and/or connector->epoch_counter changes.

In my ongoing work to convert dw-hdmi to become a hdmi bridge, I have actually done the opposite to what you suggest here and instead fully dropped the call to drm_bridge_hpd_notify() made here.

That doesnt' sound correct, but maybe it's because dw_hdmi isn't using drm_bridge_conenctor. The latter one registers a hook in the HPD bridge, which then receives the event and performs all the notifications. If the dw_hdmi doesn't do it (because you don't need it), then it's fine for now. When you work on conveting dw_hdmi to DBC, I'd recommend using the bridge notification instead (as it would then play nice with the rest of the bridge and HDMI framework).

Quoted 5 lines

drm_bridge_connector_detect() calls drm_bridge_connector_hpd_notify() so any bridges should already be notified as part of any internal check_connector_changed() handling.

Quoted 8 lines

Maybe something like following could be an option:

        changed = drm_connector_helper_hpd_irq_event(connector);
        if (changed)
                drm_bridge_hpd_notify(bridge, connector->status);

I will likely keep this as-is to keep existing behavior in a v4, as this patch was just about de-bouncing the existing calls being made at HPD.

Yep.

Quoted 48 lines

Regards,
Jonas

Quoted 43 lines
Quoted 42 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +10 -5
+            drm_bridge_hpd_notify(&hdmi->bridge, hdmi->last_connector_result);
+    }
+}
+
 static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
 {
     struct dw_hdmi *hdmi = dev_id;
@@ -3097,10 +3111,8 @@ static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
                     status == connector_status_connected ?
                     "plugin" : "plugout");
 
-            if (hdmi->bridge.dev) {
-                    drm_helper_hpd_irq_event(hdmi->bridge.dev);
-                    drm_bridge_hpd_notify(&hdmi->bridge, status);
-            }
+            mod_delayed_work(system_percpu_wq, &hdmi->hpd_work,
+                             msecs_to_jiffies(HOTPLUG_DEBOUNCE_MS));
     }
 
     hdmi_writeb(hdmi, intr_stat, HDMI_IH_PHY_STAT0);
@@ -3420,6 +3432,8 @@ struct dw_hdmi *dw_hdmi_probe(struct platform_device *pdev,
             goto err_res;
     }
 
+    INIT_DELAYED_WORK(&hdmi->hpd_work, dw_hdmi_hpd_work);
+
     ret = devm_request_threaded_irq(dev, irq, dw_hdmi_hardirq,
                                     dw_hdmi_irq, IRQF_SHARED,
                                     dev_name(dev), hdmi);
@@ -3552,6 +3566,8 @@ EXPORT_SYMBOL_GPL(dw_hdmi_probe);
 
 void dw_hdmi_remove(struct dw_hdmi *hdmi)
 {
+    disable_delayed_work_sync(&hdmi->hpd_work);
+
     drm_bridge_remove(&hdmi->bridge);
 
     if (hdmi->audio && !IS_ERR(hdmi->audio))
--

2.53.0

Signature · 2 lines
With best wishes
Dmitry
author reviewer
#16 lore raw

PATCH v3 10/13 drm: bridge: dw_hdmi: Use drm_connector_helper_hpd_irq_event()

In reply to Jonas Karlman

Use drm_connector_helper_hpd_irq_event() or drm_helper_hpd_irq_event() depending on if a dw-hdmi connector or bridge is used.

---
v3: New patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +5 -2
index 4d079b689b3b..4a0498922476 100644
@@ -3054,10 +3054,13 @@ static void dw_hdmi_hpd_work(struct work_struct *work)
 {
 	struct dw_hdmi *hdmi = container_of(work, struct dw_hdmi, hpd_work.work);
 
-	if (hdmi->bridge.dev) {
+	if (hdmi->connector.dev)
+		drm_connector_helper_hpd_irq_event(&hdmi->connector);
+	else if (hdmi->bridge.dev)
 		drm_helper_hpd_irq_event(hdmi->bridge.dev);
+
+	if (hdmi->bridge.dev)
 		drm_bridge_hpd_notify(&hdmi->bridge, hdmi->last_connector_result);
-	}
 }
 
 static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
Signature · 1 line
2.53.0
#17 lore raw

Re: [PATCH v3 10/13] drm: bridge: dw_hdmi: Use drm_connector_helper_hpd_irq_event()

Quoted 15 lines · Jonas Karlman

Use drm_connector_helper_hpd_irq_event() or drm_helper_hpd_irq_event() depending on if a dw-hdmi connector or bridge is used.

---
v3: New patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +0 -0
index 4d079b689b3b..4a0498922476 100644

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c static void dw_hdmi_hpd_work(struct work_struct *work) · line 3060

Quoted 8 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +3 -1
@@ -3054,10 +3054,13 @@ static void dw_hdmi_hpd_work(struct work_struct *work)
 {
 	struct dw_hdmi *hdmi = container_of(work, struct dw_hdmi, hpd_work.work);
 
-	if (hdmi->bridge.dev) {
+	if (hdmi->connector.dev)
+		drm_connector_helper_hpd_irq_event(&hdmi->connector);
+	else if (hdmi->bridge.dev)
 		drm_helper_hpd_irq_event(hdmi->bridge.dev);

Okay, following the comment to the previous patch it should rather become:

	if (hdmi->bridge.dev)
		drm_bridge_hpd_notify(&hdmi->bridge, hdmi->last_connector_result);
	else if (hdmi->connector.dev)
		drm_connector_helper_hpd_irq_event(&hdmi->connector);
Quoted 10 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +2 -1
+
+	if (hdmi->bridge.dev)
 		drm_bridge_hpd_notify(&hdmi->bridge, hdmi->last_connector_result);
-	}
 }
 
 static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
Signature · 1 line
2.53.0
Signature · 2 lines
With best wishes
Dmitry
author reviewer
#18 lore raw

Re: [PATCH v3 10/13] drm: bridge: dw_hdmi: Use drm_connector_helper_hpd_irq_event()

Hi Dmitry,

Quoted 28 lines · Dmitry Baryshkov
Quoted 15 lines · Jonas Karlman

Use drm_connector_helper_hpd_irq_event() or drm_helper_hpd_irq_event() depending on if a dw-hdmi connector or bridge is used.

---
v3: New patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +0 -0
index 4d079b689b3b..4a0498922476 100644

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c static void dw_hdmi_hpd_work(struct work_struct *work) · line 3060

Quoted 8 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +3 -1
@@ -3054,10 +3054,13 @@ static void dw_hdmi_hpd_work(struct work_struct *work)
 {
 	struct dw_hdmi *hdmi = container_of(work, struct dw_hdmi, hpd_work.work);
 
-	if (hdmi->bridge.dev) {
+	if (hdmi->connector.dev)
+		drm_connector_helper_hpd_irq_event(&hdmi->connector);
+	else if (hdmi->bridge.dev)
 		drm_helper_hpd_irq_event(hdmi->bridge.dev);

Okay, following the comment to the previous patch it should rather become:

Quoted 4 lines
	if (hdmi->bridge.dev)
		drm_bridge_hpd_notify(&hdmi->bridge, hdmi->last_connector_result);
	else if (hdmi->connector.dev)
		drm_connector_helper_hpd_irq_event(&hdmi->connector);

I will likely just drop this patch in a v4, as current ongoing work to convert dw-hdmi to use a bridge connector and become a hdmi bridge fully reverts the change introduced in this patch. See [1] for current work-in-progress snapshot of such ongoing work.

[1] https://github.com/Kwiboo/linux-rockchip/commits/next-20260427-rk-hdmi-v2/

Regards,
Jonas

Quoted 7 lines
Quoted 7 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +2 -1
+
+	if (hdmi->bridge.dev)
 		drm_bridge_hpd_notify(&hdmi->bridge, hdmi->last_connector_result);
-	}
 }
 
Quoted 5 lines
Quoted 4 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +0 -0
 static irqreturn_t dw_hdmi_irq(int irq, void *dev_id)
Signature · 1 line
2.53.0

_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip

author reviewer
#19 lore raw

PATCH v3 11/13 drm: bridge: dw_hdmi: Extract dw_hdmi_connector_status_update()

In reply to Jonas Karlman

Move connector EDID update and CEC phys addr handling to a helper function as a preparation before moving EDID refresh from get_modes funcs to detect/force funcs.

---
v3: New patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 30 +++++++++++++----------
 1 file changed, 17 insertions(+), 13 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +17 -13
index 4a0498922476..0d42fdf9a386 100644
@@ -2467,6 +2467,21 @@ static const struct drm_edid *dw_hdmi_edid_read(struct dw_hdmi *hdmi,
  * DRM Connector Operations
  */
 
+static void
+dw_hdmi_connector_status_update(struct drm_connector *connector,
+				enum drm_connector_status status)
+{
+	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi, connector);
+	const struct drm_edid *drm_edid;
+
+	drm_edid = dw_hdmi_edid_read(hdmi, connector);
+	drm_edid_connector_update(connector, drm_edid);
+	drm_edid_free(drm_edid);
+
+	cec_notifier_set_phys_addr(hdmi->cec_notifier,
+				   connector->display_info.source_physical_address);
+}
+
 static enum drm_connector_status
 dw_hdmi_connector_detect(struct drm_connector *connector, bool force)
 {
@@ -2484,20 +2499,9 @@ dw_hdmi_connector_detect(struct drm_connector *connector, bool force)
 
 static int dw_hdmi_connector_get_modes(struct drm_connector *connector)
 {
-	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi,
-					     connector);
-	const struct drm_edid *drm_edid;
-	int ret;
+	dw_hdmi_connector_status_update(connector, connector->status);
 
-	drm_edid = dw_hdmi_edid_read(hdmi, connector);
-
-	drm_edid_connector_update(connector, drm_edid);
-	cec_notifier_set_phys_addr(hdmi->cec_notifier,
-				   connector->display_info.source_physical_address);
-	ret = drm_edid_connector_add_modes(connector);
-	drm_edid_free(drm_edid);
-
-	return ret;
+	return drm_edid_connector_add_modes(connector);
 }
 
 static int dw_hdmi_connector_atomic_check(struct drm_connector *connector,
Signature · 1 line
2.53.0
Reviewed-by on v3 11/13
#20 lore raw

Re: [PATCH v3 11/13] drm: bridge: dw_hdmi: Extract dw_hdmi_connector_status_update()

Quoted 51 lines · On Friday, 3 April 2026 20:52:57 Central European Summer Time Jonas Karlman…

Move connector EDID update and CEC phys addr handling to a helper function as a preparation before moving EDID refresh from get_modes funcs to detect/force funcs.

---
v3: New patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 30 +++++++++++++----------
 1 file changed, 17 insertions(+), 13 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +16 -7
index 4a0498922476..0d42fdf9a386 100644
@@ -2467,6 +2467,21 @@ static const struct drm_edid *dw_hdmi_edid_read(struct dw_hdmi *hdmi,
  * DRM Connector Operations
  */
 
+static void
+dw_hdmi_connector_status_update(struct drm_connector *connector,
+				enum drm_connector_status status)
+{
+	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi, connector);
+	const struct drm_edid *drm_edid;
+
+	drm_edid = dw_hdmi_edid_read(hdmi, connector);
+	drm_edid_connector_update(connector, drm_edid);
+	drm_edid_free(drm_edid);
+
+	cec_notifier_set_phys_addr(hdmi->cec_notifier,
+				   connector->display_info.source_physical_address);
+}
+
 static enum drm_connector_status
 dw_hdmi_connector_detect(struct drm_connector *connector, bool force)
 {
@@ -2484,20 +2499,9 @@ dw_hdmi_connector_detect(struct drm_connector *connector, bool force)
 
 static int dw_hdmi_connector_get_modes(struct drm_connector *connector)
 {
-	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi,
-					     connector);
-	const struct drm_edid *drm_edid;
-	int ret;
+	dw_hdmi_connector_status_update(connector, connector->status);
 
-	drm_edid = dw_hdmi_edid_read(hdmi, connector);
-
-	drm_edid_connector_update(connector, drm_edid);

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c dw_hdmi_connector_detect(struct drm_connector *connector, bool force) · line 2507

Quoted 10 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +1 -6
-	cec_notifier_set_phys_addr(hdmi->cec_notifier,
-				   connector->display_info.source_physical_address);
-	ret = drm_edid_connector_add_modes(connector);
-	drm_edid_free(drm_edid);
-
-	return ret;
+	return drm_edid_connector_add_modes(connector);
 }
 
 static int dw_hdmi_connector_atomic_check(struct drm_connector *connector,
author reviewer
#21 lore raw

PATCH v3 12/13 drm: bridge: dw_hdmi: Use dw_hdmi_connector_status_update()

In reply to Jonas Karlman

Update connector EDID and CEC phys addr from detect and force funcs to ensure that userspace always have access to latest read EDID after a sink use a HPD low voltage pulse to indicate that EDID has changed.

With EDID being updated in detect and force funcs, there should no longer be a need to re-read EDID in get_modes funcs, so drop it.

This change make the dw-hdmi connector work more closely like the bridge connector does with a hdmi bridge.

---
v3: Reworked 'Update EDID during hotplug processing' patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 24 +++++++++++++----------
 1 file changed, 14 insertions(+), 10 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +14 -10
index 0d42fdf9a386..5b5654ef6015 100644
@@ -2474,33 +2474,36 @@ dw_hdmi_connector_status_update(struct drm_connector *connector,
 	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi, connector);
 	const struct drm_edid *drm_edid;
 
+	if (status == connector_status_disconnected) {
+		drm_edid_connector_update(connector, NULL);
+		cec_notifier_phys_addr_invalidate(hdmi->cec_notifier);
+		return;
+	}
+
 	drm_edid = dw_hdmi_edid_read(hdmi, connector);
 	drm_edid_connector_update(connector, drm_edid);
 	drm_edid_free(drm_edid);
 
-	cec_notifier_set_phys_addr(hdmi->cec_notifier,
-				   connector->display_info.source_physical_address);
+	if (status == connector_status_connected)
+		cec_notifier_set_phys_addr(hdmi->cec_notifier,
+				connector->display_info.source_physical_address);
 }
 
 static enum drm_connector_status
 dw_hdmi_connector_detect(struct drm_connector *connector, bool force)
 {
-	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi,
-					     connector);
+	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi, connector);
 	enum drm_connector_status status;
 
 	status = dw_hdmi_detect(hdmi);
 
-	if (status == connector_status_disconnected)
-		cec_notifier_phys_addr_invalidate(hdmi->cec_notifier);
+	dw_hdmi_connector_status_update(connector, status);
 
 	return status;
 }
 
 static int dw_hdmi_connector_get_modes(struct drm_connector *connector)
 {
-	dw_hdmi_connector_status_update(connector, connector->status);
-
 	return drm_edid_connector_add_modes(connector);
 }
 
@@ -2530,14 +2533,15 @@ static int dw_hdmi_connector_atomic_check(struct drm_connector *connector,
 
 static void dw_hdmi_connector_force(struct drm_connector *connector)
 {
-	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi,
-					     connector);
+	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi, connector);
 
 	mutex_lock(&hdmi->mutex);
 	hdmi->force = connector->force;
 	hdmi->last_connector_result = connector->status;
 	dw_hdmi_update_phy_mask(hdmi);
 	mutex_unlock(&hdmi->mutex);
+
+	dw_hdmi_connector_status_update(connector, connector->status);
 }
 
 static const struct drm_connector_funcs dw_hdmi_connector_funcs = {
Signature · 1 line
2.53.0
#22 lore raw

Re: [PATCH v3 12/13] drm: bridge: dw_hdmi: Use dw_hdmi_connector_status_update()

Quoted 55 lines · On Friday, 3 April 2026 20:52:58 Central European Summer Time Jonas Karlman…

Update connector EDID and CEC phys addr from detect and force funcs to ensure that userspace always have access to latest read EDID after a sink use a HPD low voltage pulse to indicate that EDID has changed.

With EDID being updated in detect and force funcs, there should no longer be a need to re-read EDID in get_modes funcs, so drop it.

This change make the dw-hdmi connector work more closely like the bridge connector does with a hdmi bridge.

---
v3: Reworked 'Update EDID during hotplug processing' patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 24 +++++++++++++----------
 1 file changed, 14 insertions(+), 10 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +11 -6
index 0d42fdf9a386..5b5654ef6015 100644
@@ -2474,33 +2474,36 @@ dw_hdmi_connector_status_update(struct drm_connector *connector,
 	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi, connector);
 	const struct drm_edid *drm_edid;
 
+	if (status == connector_status_disconnected) {
+		drm_edid_connector_update(connector, NULL);
+		cec_notifier_phys_addr_invalidate(hdmi->cec_notifier);
+		return;
+	}
+
 	drm_edid = dw_hdmi_edid_read(hdmi, connector);
 	drm_edid_connector_update(connector, drm_edid);
 	drm_edid_free(drm_edid);
 
-	cec_notifier_set_phys_addr(hdmi->cec_notifier,
-				   connector->display_info.source_physical_address);
+	if (status == connector_status_connected)
+		cec_notifier_set_phys_addr(hdmi->cec_notifier,
+				connector->display_info.source_physical_address);
 }
 
 static enum drm_connector_status
 dw_hdmi_connector_detect(struct drm_connector *connector, bool force)
 {
-	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi,
-					     connector);
+	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi, connector);
 	enum drm_connector_status status;
 
 	status = dw_hdmi_detect(hdmi);
 
-	if (status == connector_status_disconnected)
-		cec_notifier_phys_addr_invalidate(hdmi->cec_notifier);
+	dw_hdmi_connector_status_update(connector, status);

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c dw_hdmi_connector_status_update(struct drm_connector *connector, · line 2508

Quoted 10 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +0 -2
 
 	return status;
 }
 
 static int dw_hdmi_connector_get_modes(struct drm_connector *connector)
 {
-	dw_hdmi_connector_status_update(connector, connector->status);
-
 	return drm_edid_connector_add_modes(connector);
 }

Are we absolutely sure status_update is called before this, so that the EDID doesn't need to be re-read? E.g. drm_connector_helper_get_modes does do an EDID read beforehand.

Speaking of which: if we had connector->ddc set, we could just use drm_connector_helper_get_modes for this callback. But maybe it's not worth spending the time refactoring the resource handling around hdmi->ddc when the eventual goal is to refactor this all into using a bridge connector anyway.

Quoted 20 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +3 -2
@@ -2530,14 +2533,15 @@ static int dw_hdmi_connector_atomic_check(struct drm_connector *connector,
 
 static void dw_hdmi_connector_force(struct drm_connector *connector)
 {
-	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi,
-					     connector);
+	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi, connector);
 
 	mutex_lock(&hdmi->mutex);
 	hdmi->force = connector->force;
 	hdmi->last_connector_result = connector->status;
 	dw_hdmi_update_phy_mask(hdmi);
 	mutex_unlock(&hdmi->mutex);
+
+	dw_hdmi_connector_status_update(connector, connector->status);
 }
 
 static const struct drm_connector_funcs dw_hdmi_connector_funcs = {
author reviewer
#23 lore raw

Re: [PATCH v3 12/13] drm: bridge: dw_hdmi: Use dw_hdmi_connector_status_update()

Hi Nicolas,

Quoted 60 lines · Nicolas Frattaroli
Quoted 59 lines · On Friday, 3 April 2026 20:52:58 Central European Summer Time Jonas Karlman…

Update connector EDID and CEC phys addr from detect and force funcs to ensure that userspace always have access to latest read EDID after a sink use a HPD low voltage pulse to indicate that EDID has changed.

With EDID being updated in detect and force funcs, there should no longer be a need to re-read EDID in get_modes funcs, so drop it.

This change make the dw-hdmi connector work more closely like the bridge connector does with a hdmi bridge.

---
v3: Reworked 'Update EDID during hotplug processing' patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 24 +++++++++++++----------
 1 file changed, 14 insertions(+), 10 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +11 -6
index 0d42fdf9a386..5b5654ef6015 100644
@@ -2474,33 +2474,36 @@ dw_hdmi_connector_status_update(struct drm_connector *connector,
 	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi, connector);
 	const struct drm_edid *drm_edid;
 
+	if (status == connector_status_disconnected) {
+		drm_edid_connector_update(connector, NULL);
+		cec_notifier_phys_addr_invalidate(hdmi->cec_notifier);
+		return;
+	}
+
 	drm_edid = dw_hdmi_edid_read(hdmi, connector);
 	drm_edid_connector_update(connector, drm_edid);
 	drm_edid_free(drm_edid);
 
-	cec_notifier_set_phys_addr(hdmi->cec_notifier,
-				   connector->display_info.source_physical_address);
+	if (status == connector_status_connected)
+		cec_notifier_set_phys_addr(hdmi->cec_notifier,
+				connector->display_info.source_physical_address);
 }
 
 static enum drm_connector_status
 dw_hdmi_connector_detect(struct drm_connector *connector, bool force)
 {
-	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi,
-					     connector);
+	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi, connector);
 	enum drm_connector_status status;
 
 	status = dw_hdmi_detect(hdmi);
 
-	if (status == connector_status_disconnected)
-		cec_notifier_phys_addr_invalidate(hdmi->cec_notifier);
+	dw_hdmi_connector_status_update(connector, status);
 
 	return status;
 }
 
Quoted 10 lines

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c dw_hdmi_connector_status_update(struct drm_connector *connector, · line 2508

Quoted 6 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +0 -2
 static int dw_hdmi_connector_get_modes(struct drm_connector *connector)
 {
-	dw_hdmi_connector_status_update(connector, connector->status);
-
 	return drm_edid_connector_add_modes(connector);
 }

Are we absolutely sure status_update is called before this, so that the EDID doesn't need to be re-read? E.g. drm_connector_helper_get_modes does do an EDID read beforehand.

With the change to re-read EDID at .detect() we should not need to re-read EDID at .get_modes(). This also closely match how the bridge connector handle EDID update at .detect() and not .get_modes() for hdmi bridges.

At least following call paths should ensure EDID have been re-read:

drm_helper_probe_single_connector_modes():
-> connector->funcs->force()

    -> dw_hdmi_connector_force()
       -> dw_hdmi_connector_status_update()
          -> drm_edid_connector_update()             <<-- here
 -> drm_helper_probe_detect()
    -> detect_connector_status()
       -> connector->funcs->detect();
          -> dw_hdmi_connector_detect()
             -> dw_hdmi_connector_status_update()
                -> drm_edid_connector_update()       <<-- or here
 -> drm_helper_probe_get_modes()
    -> connector_funcs->get_modes()
       -> dw_hdmi_connector_get_modes()              <<-- now updated

drm_helper_hpd_irq_event():
-> detect_connector_status()

    -> connector->funcs->detect();
       -> dw_hdmi_connector_detect()
          -> dw_hdmi_connector_status_update()
             -> drm_edid_connector_update()          <<-- also after HPD
Quoted 5 lines

Speaking of which: if we had connector->ddc set, we could just use drm_connector_helper_get_modes for this callback. But maybe it's not worth spending the time refactoring the resource handling around hdmi->ddc when the eventual goal is to refactor this all into using a bridge connector anyway.

Correct, hopefully all connector related functions can be dropped from dw-hdmi in a near future when dw-hdmi is converted to a hdmi bridge.

I currently have a work-in-progress snapshot at [1] where dw-hdmi have been converted to a hdmi bridge and a bridge connector is used instead.

The changes in this series only aim to align dw-hdmi to the hdmi bridge where possible to reduce any functional change in such future series.

I will likely keep this as-is in a v4 unless there is some objections.

[1] https://github.com/Kwiboo/linux-rockchip/commits/next-20260427-rk-hdmi-v2/

Regards,
Jonas

Quoted 24 lines
Quoted 20 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +3 -2
@@ -2530,14 +2533,15 @@ static int dw_hdmi_connector_atomic_check(struct drm_connector *connector,
 
 static void dw_hdmi_connector_force(struct drm_connector *connector)
 {
-	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi,
-					     connector);
+	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi, connector);
 
 	mutex_lock(&hdmi->mutex);
 	hdmi->force = connector->force;
 	hdmi->last_connector_result = connector->status;
 	dw_hdmi_update_phy_mask(hdmi);
 	mutex_unlock(&hdmi->mutex);
+
+	dw_hdmi_connector_status_update(connector, connector->status);
 }
 
 static const struct drm_connector_funcs dw_hdmi_connector_funcs = {
Reviewed-by
#24 lore raw

Re: [PATCH v3 12/13] drm: bridge: dw_hdmi: Use dw_hdmi_connector_status_update()

Quoted 112 lines · On Tuesday, 28 April 2026 23:47:40 Central European Summer Time Jonas Karlman…

Hi Nicolas,

Quoted 60 lines · Nicolas Frattaroli
Quoted 59 lines · On Friday, 3 April 2026 20:52:58 Central European Summer Time Jonas Karlman…

Update connector EDID and CEC phys addr from detect and force funcs to ensure that userspace always have access to latest read EDID after a sink use a HPD low voltage pulse to indicate that EDID has changed.

With EDID being updated in detect and force funcs, there should no longer be a need to re-read EDID in get_modes funcs, so drop it.

This change make the dw-hdmi connector work more closely like the bridge connector does with a hdmi bridge.

---
v3: Reworked 'Update EDID during hotplug processing' patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 24 +++++++++++++----------
 1 file changed, 14 insertions(+), 10 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +11 -6
index 0d42fdf9a386..5b5654ef6015 100644
@@ -2474,33 +2474,36 @@ dw_hdmi_connector_status_update(struct drm_connector *connector,
 	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi, connector);
 	const struct drm_edid *drm_edid;
 
+	if (status == connector_status_disconnected) {
+		drm_edid_connector_update(connector, NULL);
+		cec_notifier_phys_addr_invalidate(hdmi->cec_notifier);
+		return;
+	}
+
 	drm_edid = dw_hdmi_edid_read(hdmi, connector);
 	drm_edid_connector_update(connector, drm_edid);
 	drm_edid_free(drm_edid);
 
-	cec_notifier_set_phys_addr(hdmi->cec_notifier,
-				   connector->display_info.source_physical_address);
+	if (status == connector_status_connected)
+		cec_notifier_set_phys_addr(hdmi->cec_notifier,
+				connector->display_info.source_physical_address);
 }
 
 static enum drm_connector_status
 dw_hdmi_connector_detect(struct drm_connector *connector, bool force)
 {
-	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi,
-					     connector);
+	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi, connector);
 	enum drm_connector_status status;
 
 	status = dw_hdmi_detect(hdmi);
 
-	if (status == connector_status_disconnected)
-		cec_notifier_phys_addr_invalidate(hdmi->cec_notifier);
+	dw_hdmi_connector_status_update(connector, status);
 
 	return status;
 }
 
Quoted 10 lines

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c dw_hdmi_connector_status_update(struct drm_connector *connector, · line 2508

Quoted 6 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +0 -2
 static int dw_hdmi_connector_get_modes(struct drm_connector *connector)
 {
-	dw_hdmi_connector_status_update(connector, connector->status);
-
 	return drm_edid_connector_add_modes(connector);
 }

Are we absolutely sure status_update is called before this, so that the EDID doesn't need to be re-read? E.g. drm_connector_helper_get_modes does do an EDID read beforehand.

With the change to re-read EDID at .detect() we should not need to re-read EDID at .get_modes(). This also closely match how the bridge connector handle EDID update at .detect() and not .get_modes() for hdmi bridges.

At least following call paths should ensure EDID have been re-read:

drm_helper_probe_single_connector_modes():
-> connector->funcs->force()

    -> dw_hdmi_connector_force()
       -> dw_hdmi_connector_status_update()
          -> drm_edid_connector_update()             <<-- here
 -> drm_helper_probe_detect()
    -> detect_connector_status()
       -> connector->funcs->detect();
          -> dw_hdmi_connector_detect()
             -> dw_hdmi_connector_status_update()
                -> drm_edid_connector_update()       <<-- or here
 -> drm_helper_probe_get_modes()
    -> connector_funcs->get_modes()
       -> dw_hdmi_connector_get_modes()              <<-- now updated

drm_helper_hpd_irq_event():
-> detect_connector_status()

    -> connector->funcs->detect();
       -> dw_hdmi_connector_detect()
          -> dw_hdmi_connector_status_update()
             -> drm_edid_connector_update()          <<-- also after HPD
Quoted 5 lines

Speaking of which: if we had connector->ddc set, we could just use drm_connector_helper_get_modes for this callback. But maybe it's not worth spending the time refactoring the resource handling around hdmi->ddc when the eventual goal is to refactor this all into using a bridge connector anyway.

Correct, hopefully all connector related functions can be dropped from dw-hdmi in a near future when dw-hdmi is converted to a hdmi bridge.

Quoted 7 lines

I currently have a work-in-progress snapshot at [1] where dw-hdmi have been converted to a hdmi bridge and a bridge connector is used instead.

The changes in this series only aim to align dw-hdmi to the hdmi bridge where possible to reduce any functional change in such future series.

I will likely keep this as-is in a v4 unless there is some objections.

With that explanation, I'm on board with this. So:

Kind regards,
Nicolas Frattaroli

Quoted 32 lines

[1] https://github.com/Kwiboo/linux-rockchip/commits/next-20260427-rk-hdmi-v2/

Regards,
Jonas

Quoted 24 lines
Quoted 20 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +3 -2
@@ -2530,14 +2533,15 @@ static int dw_hdmi_connector_atomic_check(struct drm_connector *connector,
 
 static void dw_hdmi_connector_force(struct drm_connector *connector)
 {
-	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi,
-					     connector);
+	struct dw_hdmi *hdmi = container_of(connector, struct dw_hdmi, connector);
 
 	mutex_lock(&hdmi->mutex);
 	hdmi->force = connector->force;
 	hdmi->last_connector_result = connector->status;
 	dw_hdmi_update_phy_mask(hdmi);
 	mutex_unlock(&hdmi->mutex);
+
+	dw_hdmi_connector_status_update(connector, connector->status);
 }
 
 static const struct drm_connector_funcs dw_hdmi_connector_funcs = {
#25 lore raw

Re: [PATCH v3 12/13] drm: bridge: dw_hdmi: Use dw_hdmi_connector_status_update()

In reply to Jonas Karlman
Quoted 9 lines · Jonas Karlman

Update connector EDID and CEC phys addr from detect and force funcs to ensure that userspace always have access to latest read EDID after a sink use a HPD low voltage pulse to indicate that EDID has changed.

With EDID being updated in detect and force funcs, there should no longer be a need to re-read EDID in get_modes funcs, so drop it.

This change make the dw-hdmi connector work more closely like the bridge connector does with a hdmi bridge.

Please consider using drm_atomic_helper_connector_hdmi_update() directly.

Quoted 8 lines

---
v3: Reworked 'Update EDID during hotplug processing' patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 24 +++++++++++++----------
 1 file changed, 14 insertions(+), 10 deletions(-)
Signature · 2 lines
With best wishes
Dmitry
author reviewer
#26 lore raw

Re: [PATCH v3 12/13] drm: bridge: dw_hdmi: Use dw_hdmi_connector_status_update()

Hi Dmitry,

Quoted 5 lines · Dmitry Baryshkov
Quoted 4 lines · Jonas Karlman

Update connector EDID and CEC phys addr from detect and force funcs to ensure that userspace always have access to latest read EDID after a sink use a HPD low voltage pulse to indicate that EDID has changed.

Quoted 8 lines
Quoted 5 lines

With EDID being updated in detect and force funcs, there should no longer be a need to re-read EDID in get_modes funcs, so drop it.

This change make the dw-hdmi connector work more closely like the bridge connector does with a hdmi bridge.

Please consider using drm_atomic_helper_connector_hdmi_update() directly.

It is unfortunately not possible to use that helper unless connector->hdmi.funcs has been assigned a value, currently something that is only done in drmm_connector_hdmi_init().

As briefly mentioned in the cover letter, I am working on converting dw-hdmi to be a hdmi bridge, so this function will be replaced/removed in a future series.

See [1] for a work-in-progres snapshot where dw-hdmi use the bridge connector and has been converted to a hdmi bridge. This works great on Rockchip RK3328, RK3399 and RK3568. More testing and cleanup is needed before something beyond the initial HPD, CEC and EDID rework/cleanup currently handled in this series is ready for posing to ML.

[1] https://github.com/Kwiboo/linux-rockchip/commits/next-20260427-rk-hdmi-v2/

Regards,
Jonas

Quoted 10 lines
Quoted 9 lines

---
v3: Reworked 'Update EDID during hotplug processing' patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 24 +++++++++++++----------
 1 file changed, 14 insertions(+), 10 deletions(-)
#27 lore raw

Re: [PATCH v3 12/13] drm: bridge: dw_hdmi: Use dw_hdmi_connector_status_update()

Quoted 15 lines · Jonas Karlman

Hi Dmitry,

Quoted 11 lines · Dmitry Baryshkov
Quoted 9 lines · Jonas Karlman

Update connector EDID and CEC phys addr from detect and force funcs to ensure that userspace always have access to latest read EDID after a sink use a HPD low voltage pulse to indicate that EDID has changed.

With EDID being updated in detect and force funcs, there should no longer be a need to re-read EDID in get_modes funcs, so drop it.

This change make the dw-hdmi connector work more closely like the bridge connector does with a hdmi bridge.

Quoted 6 lines
Quoted 2 lines

Please consider using drm_atomic_helper_connector_hdmi_update() directly.

It is unfortunately not possible to use that helper unless connector->hdmi.funcs has been assigned a value, currently something that is only done in drmm_connector_hdmi_init().

Ack. Looking forward to reviewing your patches.

Quoted 27 lines

As briefly mentioned in the cover letter, I am working on converting dw-hdmi to be a hdmi bridge, so this function will be replaced/removed in a future series.

See [1] for a work-in-progres snapshot where dw-hdmi use the bridge connector and has been converted to a hdmi bridge. This works great on Rockchip RK3328, RK3399 and RK3568. More testing and cleanup is needed before something beyond the initial HPD, CEC and EDID rework/cleanup currently handled in this series is ready for posing to ML.

[1] https://github.com/Kwiboo/linux-rockchip/commits/next-20260427-rk-hdmi-v2/

Regards,
Jonas

Quoted 10 lines
Quoted 9 lines

---
v3: Reworked 'Update EDID during hotplug processing' patch

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 24 +++++++++++++----------
 1 file changed, 14 insertions(+), 10 deletions(-)
Signature · 2 lines
With best wishes
Dmitry
author reviewer
#28 lore raw

PATCH v3 13/13 drm: bridge: dw_hdmi: Use display_info is_hdmi and has_audio

In reply to Jonas Karlman

drm_edid_connector_update() is being called from bridge connector funcs and from detect and force funcs for dw-hdmi connector.

Change to use is_hdmi and has_audio from display_info directly instead of keeping our own state in sink_is_hdmi and sink_has_audio.

Also remove the old and unused edid struct member and related define.

---
v3: No change
v2: Collect r-b tag

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 32 ++++-------------------
 1 file changed, 5 insertions(+), 27 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +5 -27
index 5b5654ef6015..fecbc386871d 100644
@@ -44,8 +44,6 @@
 #define DDC_CI_ADDR		0x37
 #define DDC_SEGMENT_ADDR	0x30
 
-#define HDMI_EDID_LEN		512
-
 /* DW-HDMI Controller >= 0x200a are at least compliant with SCDC version 1 */
 #define SCDC_MIN_SOURCE_VERSION	0x1
 
@@ -147,8 +145,6 @@ struct dw_hdmi {
 
 	int vic;
 
-	u8 edid[HDMI_EDID_LEN];
-
 	struct {
 		const struct dw_hdmi_phy_ops *ops;
 		const char *name;
@@ -158,8 +154,6 @@ struct dw_hdmi {
 
 	struct i2c_adapter *ddc;
 	void __iomem *regs;
-	bool sink_is_hdmi;
-	bool sink_has_audio;
 
 	struct pinctrl *pinctrl;
 	struct pinctrl_state *default_state;
@@ -2057,7 +2051,7 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi,
 		HDMI_FC_INVIDCONF_IN_I_P_INTERLACED :
 		HDMI_FC_INVIDCONF_IN_I_P_PROGRESSIVE;
 
-	inv_val |= hdmi->sink_is_hdmi ?
+	inv_val |= display->is_hdmi ?
 		HDMI_FC_INVIDCONF_DVI_MODEZ_HDMI_MODE :
 		HDMI_FC_INVIDCONF_DVI_MODEZ_DVI_MODE;
 
@@ -2293,7 +2287,7 @@ static int dw_hdmi_poweron(struct dw_hdmi *hdmi,
 	if (hdmi->hdmi_data.enc_out_bus_format == MEDIA_BUS_FMT_FIXED)
 		hdmi->hdmi_data.enc_out_bus_format = MEDIA_BUS_FMT_RGB888_1X24;
 
-	hdmi->hdmi_data.rgb_limited_range = hdmi->sink_is_hdmi &&
+	hdmi->hdmi_data.rgb_limited_range = display->is_hdmi &&
 		drm_default_rgb_quant_range(mode) ==
 		HDMI_QUANTIZATION_RANGE_LIMITED;
 
@@ -2313,7 +2307,7 @@ static int dw_hdmi_poweron(struct dw_hdmi *hdmi,
 	/* HDMI Initialization Step B.3 */
 	dw_hdmi_enable_video_path(hdmi);
 
-	if (hdmi->sink_has_audio) {
+	if (display->has_audio) {
 		dev_dbg(hdmi->dev, "sink has audio support\n");
 
 		/* HDMI Initialization Step E - Configure audio */
@@ -2322,7 +2316,7 @@ static int dw_hdmi_poweron(struct dw_hdmi *hdmi,
 	}
 
 	/* not for DVI mode */
-	if (hdmi->sink_is_hdmi) {
+	if (display->is_hdmi) {
 		dev_dbg(hdmi->dev, "%s HDMI mode\n", __func__);
 
 		/* HDMI Initialization Step F - Configure AVI InfoFrame */
@@ -2436,29 +2430,13 @@ static const struct drm_edid *dw_hdmi_edid_read(struct dw_hdmi *hdmi,
 						struct drm_connector *connector)
 {
 	const struct drm_edid *drm_edid;
-	const struct edid *edid;
 
 	if (!hdmi->ddc)
 		return NULL;
 
 	drm_edid = drm_edid_read_ddc(connector, hdmi->ddc);
-	if (!drm_edid) {
+	if (!drm_edid)
 		dev_dbg(hdmi->dev, "failed to get edid\n");
-		return NULL;
-	}
-
-	/*
-	 * FIXME: This should use connector->display_info.is_hdmi and
-	 * connector->display_info.has_audio from a path that has read the EDID
-	 * and called drm_edid_connector_update().
-	 */
-	edid = drm_edid_raw(drm_edid);
-
-	dev_dbg(hdmi->dev, "got edid: width[%d] x height[%d]\n",
-		edid->width_cm, edid->height_cm);
-
-	hdmi->sink_is_hdmi = drm_detect_hdmi_monitor(edid);
-	hdmi->sink_has_audio = drm_detect_monitor_audio(edid);
 
 	return drm_edid;
 }
Signature · 1 line
2.53.0
Reviewed-by on v3 13/13
#29 lore raw

Re: [PATCH v3 13/13] drm: bridge: dw_hdmi: Use display_info is_hdmi and has_audio

Quoted 106 lines · On Friday, 3 April 2026 20:52:59 Central European Summer Time Jonas Karlman…

drm_edid_connector_update() is being called from bridge connector funcs and from detect and force funcs for dw-hdmi connector.

Change to use is_hdmi and has_audio from display_info directly instead of keeping our own state in sink_is_hdmi and sink_has_audio.

Also remove the old and unused edid struct member and related define.

---
v3: No change
v2: Collect r-b tag

---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 32 ++++-------------------
 1 file changed, 5 insertions(+), 27 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +5 -20
index 5b5654ef6015..fecbc386871d 100644
@@ -44,8 +44,6 @@
 #define DDC_CI_ADDR		0x37
 #define DDC_SEGMENT_ADDR	0x30
 
-#define HDMI_EDID_LEN		512
-
 /* DW-HDMI Controller >= 0x200a are at least compliant with SCDC version 1 */
 #define SCDC_MIN_SOURCE_VERSION	0x1
 
@@ -147,8 +145,6 @@ struct dw_hdmi {
 
 	int vic;
 
-	u8 edid[HDMI_EDID_LEN];
-
 	struct {
 		const struct dw_hdmi_phy_ops *ops;
 		const char *name;
@@ -158,8 +154,6 @@ struct dw_hdmi {
 
 	struct i2c_adapter *ddc;
 	void __iomem *regs;
-	bool sink_is_hdmi;
-	bool sink_has_audio;
 
 	struct pinctrl *pinctrl;
 	struct pinctrl_state *default_state;
@@ -2057,7 +2051,7 @@ static void hdmi_av_composer(struct dw_hdmi *hdmi,
 		HDMI_FC_INVIDCONF_IN_I_P_INTERLACED :
 		HDMI_FC_INVIDCONF_IN_I_P_PROGRESSIVE;
 
-	inv_val |= hdmi->sink_is_hdmi ?
+	inv_val |= display->is_hdmi ?
 		HDMI_FC_INVIDCONF_DVI_MODEZ_HDMI_MODE :
 		HDMI_FC_INVIDCONF_DVI_MODEZ_DVI_MODE;
 
@@ -2293,7 +2287,7 @@ static int dw_hdmi_poweron(struct dw_hdmi *hdmi,
 	if (hdmi->hdmi_data.enc_out_bus_format == MEDIA_BUS_FMT_FIXED)
 		hdmi->hdmi_data.enc_out_bus_format = MEDIA_BUS_FMT_RGB888_1X24;
 
-	hdmi->hdmi_data.rgb_limited_range = hdmi->sink_is_hdmi &&
+	hdmi->hdmi_data.rgb_limited_range = display->is_hdmi &&
 		drm_default_rgb_quant_range(mode) ==
 		HDMI_QUANTIZATION_RANGE_LIMITED;
 
@@ -2313,7 +2307,7 @@ static int dw_hdmi_poweron(struct dw_hdmi *hdmi,
 	/* HDMI Initialization Step B.3 */
 	dw_hdmi_enable_video_path(hdmi);
 
-	if (hdmi->sink_has_audio) {
+	if (display->has_audio) {
 		dev_dbg(hdmi->dev, "sink has audio support\n");
 
 		/* HDMI Initialization Step E - Configure audio */
@@ -2322,7 +2316,7 @@ static int dw_hdmi_poweron(struct dw_hdmi *hdmi,
 	}
 
 	/* not for DVI mode */
-	if (hdmi->sink_is_hdmi) {
+	if (display->is_hdmi) {
 		dev_dbg(hdmi->dev, "%s HDMI mode\n", __func__);
 
 		/* HDMI Initialization Step F - Configure AVI InfoFrame */
@@ -2436,29 +2430,13 @@ static const struct drm_edid *dw_hdmi_edid_read(struct dw_hdmi *hdmi,
 						struct drm_connector *connector)
 {
 	const struct drm_edid *drm_edid;
-	const struct edid *edid;
 
 	if (!hdmi->ddc)
 		return NULL;
 
 	drm_edid = drm_edid_read_ddc(connector, hdmi->ddc);
-	if (!drm_edid) {
+	if (!drm_edid)
 		dev_dbg(hdmi->dev, "failed to get edid\n");
-		return NULL;
-	}
-
-	/*
-	 * FIXME: This should use connector->display_info.is_hdmi and
-	 * connector->display_info.has_audio from a path that has read the EDID
-	 * and called drm_edid_connector_update().
-	 */

drivers/gpu/drm/bridge/synopsys/dw-hdmi.c static const struct drm_edid *dw_hdmi_edid_read(struct dw_hdmi *hdmi, · line 2442

Quoted 10 lines
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +0 -7
-	edid = drm_edid_raw(drm_edid);
-
-	dev_dbg(hdmi->dev, "got edid: width[%d] x height[%d]\n",
-		edid->width_cm, edid->height_cm);
-
-	hdmi->sink_is_hdmi = drm_detect_hdmi_monitor(edid);
-	hdmi->sink_has_audio = drm_detect_monitor_audio(edid);
 
 	return drm_edid;
 }
Tested-by on the v3 series
#30 lore raw
In reply to Jonas Karlman
Quoted 6 lines · Jonas Karlman

drm: bridge: dw_hdmi: Misc enable/disable, CEC and EDID cleanup

This is a revival of an old dw-hdmi series and is the first series part of a new effort to upstream old LibreELEC HDMI 2.0 patches for Rockchip RK33xx devices.

Quoted 6 lines

This series ensure poweron/poweroff and CEC phys addr invalidation is happening under drm mode_config mutex lock, and also ensure EDID is updated after a HPD low voltage pulse by changing to debounce hotplug processing.

[...]

Signature · 6 lines
Bob McChesney <[email protected]>

_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
Tested-by on the v3 series
#31 lore raw
In reply to Jonas Karlman
Quoted 6 lines · Jonas Karlman

drm: bridge: dw_hdmi: Misc enable/disable, CEC and EDID cleanup

This is a revival of an old dw-hdmi series and is the first series part of a new effort to upstream old LibreELEC HDMI 2.0 patches for Rockchip RK33xx devices.

Quoted 6 lines

This series ensure poweron/poweroff and CEC phys addr invalidation is happening under drm mode_config mutex lock, and also ensure EDID is updated after a HPD low voltage pulse by changing to debounce hotplug processing.

[...]

Signature · 1 line
Bob McChesney <[email protected]>