iio: adc: nxp-sar-adc: Avoid division by zero
PATCH 1/1 iio: adc: nxp-sar-adc: Avoid division by zero
When Common Clock Framework is disabled, clk_get_rate() returns 0. This is used as part of the divisor to perform nanosecond delays with help of ndelay(). When the above condition occurs the compiler, due to unspecified behaviour, is free to do what it wants to. Here it saturates the value, which is logical from mathematics point of view. However, the ndelay() implementation has set a reasonable upper threshold and refuses to provide anything for such a long delay. That's why code may not be linked under these circumstances.
To solve the issue, provide a wrapper that calls ndelay() when the value is known not to be zero.
--- drivers/iio/adc/nxp-sar-adc.c | 13 +++++++++++-- 1 file changed, 11 insertions(+), 2 deletions(-)
drivers/iio/adc/nxp-sar-adc.c +11 -2
@@ -198,6 +198,15 @@ static void nxp_sar_adc_irq_cfg(struct nxp_sar_adc *info, bool enable)writel (0 ,NXP_SAR_ADC_IMR (info->regs)); } +static void nxp_sar_adc_wait_for (struct nxp_sar_adc *info,unsigned int cycles) +{ +u64 rate; + + rate =clk_get_rate (info->clk); +if (rate) +ndelay (div64_u64 (NSEC_PER_SEC , rate * cycles)); +} +static bool nxp_sar_adc_set_enabled (struct nxp_sar_adc *info,bool enable) {u32 mcr;
@@ -221,7 +230,7 @@ static bool nxp_sar_adc_set_enabled(struct nxp_sar_adc *info, bool enable)* configuration of NCMR and the setting of NSTART. */ if (enable) -ndelay (div64_u64 (NSEC_PER_SEC ,clk_get_rate (info->clk) *3 )); +nxp_sar_adc_wait_for (info,3 );return pwdn; }
@@ -469,7 +478,7 @@ static void nxp_sar_adc_stop_conversion(struct nxp_sar_adc *info)* only when the capture finishes. The delay will be very * short, usec-ish, which is acceptable in the atomic context. */ -ndelay (div64_u64 (NSEC_PER_SEC ,clk_get_rate (info->clk)) *80 ); +nxp_sar_adc_wait_for (info,80 ); }static int nxp_sar_adc_start_conversion (struct nxp_sar_adc *info,bool raw)
Signature · 1 line
2.50.1
Hi Andy,
Quoted 9 lines · Andy Shevchenko
When Common Clock Framework is disabled,
clk_get_rate()returns 0. This is used as part of the divisor to perform nanosecond delays with help ofndelay(). When the above condition occurs the compiler, due to unspecified behaviour, is free to do what it wants to. Here it saturates the value, which is logical from mathematics point of view. However, thendelay()implementation has set a reasonable upper threshold and refuses to provide anything for such a long delay. That's why code may not be linked under these circumstances.
Quoted 7 lines
To solve the issue, provide a wrapper that calls
ndelay()when the value is known not to be zero.Fixes 4434072a893e ("iio: adc: Add the NXP SAR ADC support for the s32g2/3 platforms")Reported-by kernel test robot <[email protected]>Signed-off-by Andy Shevchenko <[email protected]>
Quoted 42 lines
--- drivers/iio/adc/nxp-sar-adc.c | 13 +++++++++++-- 1 file changed, 11 insertions(+), 2 deletions(-)drivers/iio/adc/nxp-sar-adc.c +11
-2@@ -198,6 +198,15 @@ static void nxp_sar_adc_irq_cfg(struct nxp_sar_adc *info, bool enable)writel (0 ,NXP_SAR_ADC_IMR (info->regs)); } +static void nxp_sar_adc_wait_for (struct nxp_sar_adc *info,unsigned int cycles) +{ +u64 rate; + + rate =clk_get_rate (info->clk); +if (rate) +ndelay (div64_u64 (NSEC_PER_SEC , rate * cycles)); +} +static bool nxp_sar_adc_set_enabled (struct nxp_sar_adc *info,bool enable) {u32 mcr;@@ -221,7 +230,7 @@ static bool nxp_sar_adc_set_enabled(struct nxp_sar_adc *info, bool enable)* configuration of NCMR and the setting of NSTART. */ if (enable) -ndelay (div64_u64 (NSEC_PER_SEC ,clk_get_rate (info->clk) *3 )); +nxp_sar_adc_wait_for (info,3 );return pwdn; }@@ -469,7 +478,7 @@ static void nxp_sar_adc_stop_conversion(struct nxp_sar_adc *info)* only when the capture finishes. The delay will be very * short, usec-ish, which is acceptable in the atomic context. */ -ndelay (div64_u64 (NSEC_PER_SEC ,clk_get_rate (info->clk)) *80 ); +nxp_sar_adc_wait_for (info,80 ); }static int nxp_sar_adc_start_conversion (struct nxp_sar_adc *info,bool raw)
Quoted 9 lines · On Thu, 16 Apr 2026 11:01:22 +0200 Andy Shevchenko…
When Common Clock Framework is disabled,
clk_get_rate()returns 0. This is used as part of the divisor to perform nanosecond delays with help ofndelay(). When the above condition occurs the compiler, due to unspecified behaviour, is free to do what it wants to. Here it saturates the value, which is logical from mathematics point of view. However, thendelay()implementation has set a reasonable upper threshold and refuses to provide anything for such a long delay. That's why code may not be linked under these circumstances.
Quoted 7 lines
To solve the issue, provide a wrapper that calls
ndelay()when the value is known not to be zero.Fixes 4434072a893e ("iio: adc: Add the NXP SAR ADC support for the s32g2/3 platforms")Reported-by kernel test robot <[email protected]>Signed-off-by Andy Shevchenko <[email protected]>
Applied to the fixes-togreg branch of iio.git and marked for stable. Thanks,
Jonathan