Skip to contentSkip to conversation

add Toradex Verdin iMX95 support

PATCH In review Emanuele Ghidoli 2 participants 8 messages Apr 17

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

v2 cover add Toradex Verdin iMX95 support

From: Emanuele Ghidoli <[email protected]>

This series adds initial U-Boot support for the Toradex Verdin iMX95.

It also introduces a new RAM-size probing helper based on alias checks. On Verdin iMX95, the first DDR region is reserved for Cortex-M7 firmware and the get_ram_size() could not be used to detect the actual RAM size. Using explicit probe/alias pairs provides reliable size detection for the supported memory variants.

The board DT is currently aligned with linux-next. Once the board DTS is in mainline Linux, we'll move to OF_UPSTREAM.

v2:
- add check for CONFIG_IS_ENABLED(SYS_DCACHE_OFF) in probe_ram_size_by_alias
- renamed ram_alias_check variable to ram_alias_checks. Added static qualifier.
- fixed typo in verdin-imx95.h: determited -> determined

v1: https://lore.kernel.org/u-boot/[email protected]/

Emanuele Ghidoli (3):
common: memsize: add RAM size probe based on alias detection
board: toradex: add Toradex Verdin iMX95
toradex: tdx-cfg-block: add verdin imx95 0226, 0227 and 0228 pid4

 arch/arm/dts/imx95-verdin-dev.dtsi            |  239 ++++
 .../arm/dts/imx95-verdin-wifi-dev-u-boot.dtsi |  112 ++
 arch/arm/dts/imx95-verdin-wifi-dev.dts        |   21 +
 arch/arm/dts/imx95-verdin-wifi.dtsi           |   50 +
 arch/arm/dts/imx95-verdin.dtsi                | 1172 +++++++++++++++++
 arch/arm/mach-imx/imx9/Kconfig                |    5 +
 board/toradex/common/tdx-cfg-block.c          |    3 +
 board/toradex/common/tdx-cfg-block.h          |    3 +
 board/toradex/verdin-imx95/Kconfig            |   36 +
 board/toradex/verdin-imx95/MAINTAINERS        |   13 +
 board/toradex/verdin-imx95/Makefile           |    8 +
 board/toradex/verdin-imx95/spl.c              |   75 ++
 board/toradex/verdin-imx95/verdin-imx95.c     |   80 ++
 board/toradex/verdin-imx95/verdin-imx95.env   |   20 +
 common/memsize.c                              |   59 +
 configs/verdin-imx95_defconfig                |  183 +++
 doc/board/toradex/index.rst                   |    1 +
 doc/board/toradex/verdin-imx95.rst            |  171 +++
 include/configs/verdin-imx95.h                |   27 +
 include/init.h                                |    7 +
 20 files changed, 2285 insertions(+)
 create mode 100644 arch/arm/dts/imx95-verdin-dev.dtsi
 create mode 100644 arch/arm/dts/imx95-verdin-wifi-dev-u-boot.dtsi
 create mode 100644 arch/arm/dts/imx95-verdin-wifi-dev.dts
 create mode 100644 arch/arm/dts/imx95-verdin-wifi.dtsi
 create mode 100644 arch/arm/dts/imx95-verdin.dtsi
 create mode 100644 board/toradex/verdin-imx95/Kconfig
 create mode 100644 board/toradex/verdin-imx95/MAINTAINERS
 create mode 100644 board/toradex/verdin-imx95/Makefile
 create mode 100644 board/toradex/verdin-imx95/spl.c
 create mode 100644 board/toradex/verdin-imx95/verdin-imx95.c
 create mode 100644 board/toradex/verdin-imx95/verdin-imx95.env
 create mode 100644 configs/verdin-imx95_defconfig
 create mode 100644 doc/board/toradex/verdin-imx95.rst
 create mode 100644 include/configs/verdin-imx95.h
Signature · 1 line
2.43.0
#1 lore raw

PATCH v2 1/3 common: memsize: add RAM size probe based on alias detection

From: Emanuele Ghidoli <[email protected]>

Add probe_ram_size_by_alias() to detect RAM size by checking whether a write to one address aliases to another address.

Compared to get_ram_size(), this function allows the caller to:
- limit probing to a small set of required accesses
- avoid touching reserved or already used memory regions
- handle non-linear alias patterns

On the iMX95 SoC, when used with LPDDR5, accesses beyond the end of an 8GB DDR configuration do not alias to the expected linear wrap-around addresses. Instead, the aliased addresses appear to follow a pattern related to the DDRC bank and bank-group addresses mapping. Experimentally, the observed pattern is:

Write Read
y00000000 -> x0001c000
y00004000 -> x00018000
y00008000 -> x00014000
y0000c000 -> x00010000
y00010000 -> x0000c000
y00014000 -> x00008000
y00018000 -> x00004000
y0001c000 -> x00000000

This helper makes it possible to probe RAM size by explicitly specifying the probed address and the expected alias address for each size check.

---
 common/memsize.c | 59 ++++++++++++++++++++++++++++++++++++++++++++++++
 include/init.h   |  7 ++++++
 2 files changed, 66 insertions(+)
common/memsize.c +59 -0
index 1abf3fc47d73..3ecf9bac2aac 100644
@@ -127,6 +127,65 @@ long get_ram_size(long *base, long maxsize)
 	return (maxsize);
 }
 
+/**
+ * probe_ram_size_by_alias() - Detect RAM size using known alias addresses
+ * @checks: Array of RAM alias probe descriptors, terminated by a NULL
+ *	    @probe_addr entry
+ *
+ * Probe RAM size by writing a test pattern to each @probe_addr and checking
+ * whether the same pattern does not appear at the corresponding @alias_addr.
+ * This is useful on systems where address wrap-around does not alias to the
+ * base of memory in a linear way, so get_ram_size() cannot be used directly.
+ * It is also useful on systems where the base of the physical memory cannot
+ * be safely accessed, so get_ram_size() cannot be used at all.
+ *
+ * Return: The size associated with the first matching entry, or 0 if no match
+ * is found.
+ */
+long probe_ram_size_by_alias(const struct ram_alias_check *checks)
+{
+	long save[2];
+	int dcache_en = 0;
+	long ret = 0;
+
+	if (!CONFIG_IS_ENABLED(SYS_DCACHE_OFF))
+		dcache_en = dcache_status();
+
+	while (checks->probe_addr && !ret) {
+		volatile long *d = checks->probe_addr;
+		volatile long *s = checks->alias_addr;
+
+		save[0] = *s;
+		save[1] = *d;
+		/* Ensure s is written and not cached */
+		if (dcache_en)
+			dcache_flush_invalidate(s);
+
+		*d = ~save[0];
+		sync();
+		if (dcache_en)
+			dcache_flush_invalidate(d);
+
+		if (*s != ~save[0])
+			ret = checks->size;
+
+		/* Restore content */
+		*d = save[1];
+		sync();
+		if (dcache_en)
+			dcache_flush_invalidate(d);
+
+		*s = save[0];
+		sync();
+		if (dcache_en)
+			dcache_flush_invalidate(s);
+
+		checks++;
+	}
+
+	return ret;
+}
+
 phys_size_t __weak get_effective_memsize(void)
 {
 	phys_size_t ram_size = gd->ram_size;
include/init.h +7 -0
index 1e375da48936..c31ebd83b85e 100644
@@ -14,6 +14,12 @@
 
 #include <linux/types.h>
 
+struct ram_alias_check {
+	void *probe_addr;
+	void *alias_addr;
+	long size;
+};
+
 /*
  * In case of the EFI app the UEFI firmware provides the low-level
  * initialisation.
@@ -88,6 +94,7 @@ int dram_init(void);
 int dram_init_banksize(void);
 
 long get_ram_size(long *base, long size);
+long probe_ram_size_by_alias(const struct ram_alias_check *checks);
 phys_size_t get_effective_memsize(void);
 
 int testdram(void);
Signature · 1 line
2.43.0
#3 lore raw

PATCH v2 2/3 board: toradex: add Toradex Verdin iMX95

In reply to Emanuele Ghidoli

From: Emanuele Ghidoli <[email protected]>

Add support for the Toradex Verdin iMX95.

---
 arch/arm/dts/imx95-verdin-dev.dtsi            |  239 ++++
 .../arm/dts/imx95-verdin-wifi-dev-u-boot.dtsi |  112 ++
 arch/arm/dts/imx95-verdin-wifi-dev.dts        |   21 +
 arch/arm/dts/imx95-verdin-wifi.dtsi           |   50 +
 arch/arm/dts/imx95-verdin.dtsi                | 1172 +++++++++++++++++
 arch/arm/mach-imx/imx9/Kconfig                |    5 +
 board/toradex/verdin-imx95/Kconfig            |   36 +
 board/toradex/verdin-imx95/MAINTAINERS        |   13 +
 board/toradex/verdin-imx95/Makefile           |    8 +
 board/toradex/verdin-imx95/spl.c              |   75 ++
 board/toradex/verdin-imx95/verdin-imx95.c     |   79 ++
 board/toradex/verdin-imx95/verdin-imx95.env   |   20 +
 configs/verdin-imx95_defconfig                |  183 +++
 doc/board/toradex/index.rst                   |    1 +
 doc/board/toradex/verdin-imx95.rst            |  171 +++
 include/configs/verdin-imx95.h                |   27 +
 16 files changed, 2212 insertions(+)
 create mode 100644 arch/arm/dts/imx95-verdin-dev.dtsi
 create mode 100644 arch/arm/dts/imx95-verdin-wifi-dev-u-boot.dtsi
 create mode 100644 arch/arm/dts/imx95-verdin-wifi-dev.dts
 create mode 100644 arch/arm/dts/imx95-verdin-wifi.dtsi
 create mode 100644 arch/arm/dts/imx95-verdin.dtsi
 create mode 100644 board/toradex/verdin-imx95/Kconfig
 create mode 100644 board/toradex/verdin-imx95/MAINTAINERS
 create mode 100644 board/toradex/verdin-imx95/Makefile
 create mode 100644 board/toradex/verdin-imx95/spl.c
 create mode 100644 board/toradex/verdin-imx95/verdin-imx95.c
 create mode 100644 board/toradex/verdin-imx95/verdin-imx95.env
 create mode 100644 configs/verdin-imx95_defconfig
 create mode 100644 doc/board/toradex/verdin-imx95.rst
 create mode 100644 include/configs/verdin-imx95.h
arch/arm/dts/imx95-verdin-dev.dtsi new file +239 -0
new file mode 100644
index 000000000000..803480eef476
@@ -0,0 +1,239 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) Toradex
+ *
+ * Common dtsi for Verdin iMX95 SoM on development carrier board
+ *
+ * https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx95
+ * https://www.toradex.com/products/carrier-board/verdin-development-board-kit
+ */
+
+/ {
+	aliases {
+		eeprom1 = &carrier_eeprom;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,bitclock-master = <&codec_dai>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&codec_dai>;
+		simple-audio-card,mclk-fs = <256>;
+		simple-audio-card,name = "verdin-nau8822";
+		simple-audio-card,routing =
+			"Headphones", "LHP",
+			"Headphones", "RHP",
+			"Speaker", "LSPK",
+			"Speaker", "RSPK",
+			"Line Out", "AUXOUT1",
+			"Line Out", "AUXOUT2",
+			"LAUX", "Line In",
+			"RAUX", "Line In",
+			"LMICP", "Mic In",
+			"RMICP", "Mic In";
+		simple-audio-card,widgets =
+			"Headphones", "Headphones",
+			"Line Out", "Line Out",
+			"Speaker", "Speaker",
+			"Microphone", "Mic In",
+			"Line", "Line In";
+
+		codec_dai: simple-audio-card,codec {
+			clocks = <&scmi_clk IMX95_CLK_SAI3>;
+			sound-dai = <&nau8822_1a>;
+		};
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai3>;
+		};
+	};
+};
+
+/* Verdin ADC_1, ADC_2, ADC_3 and ADC_4 */
+&adc1 {
+	status = "okay";
+};
+
+/* Verdin ETH_1 (On-module PHY) */
+&enetc_port0 {
+	status = "okay";
+};
+
+/* Verdin ETH_2_RGMII */
+&enetc_port1 {
+	phy-handle = <&ethphy2>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+/* Verdin QSPI_1 */
+&flexspi1 {
+	status = "okay";
+};
+
+&gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ctrl_sleep_moci>;
+};
+
+&gpio2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1>,
+		    <&pinctrl_gpio2>,
+		    <&pinctrl_gpio3>;
+};
+
+&gpio3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio6>;
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio5>;
+};
+
+&gpio5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio4>;
+};
+
+/* Verdin I2C_3_HDMI */
+&i3c2 {
+	status = "okay";
+};
+
+/* Verdin I2C_2_DSI */
+&lpi2c3 {
+	status = "okay";
+};
+
+/* Verdin I2C_1 */
+&lpi2c4 {
+	status = "okay";
+
+	nau8822_1a: audio-codec@1a {
+		compatible = "nuvoton,nau8822";
+		reg = <0x1a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sai3_mclk>;
+		#sound-dai-cells = <0>;
+	};
+
+	carrier_gpio_expander: gpio@21 {
+		compatible = "nxp,pcal6416";
+		reg = <0x21>;
+		#gpio-cells = <2>;
+		gpio-controller;
+	};
+
+	/* Current measurement into module VCC */
+	hwmon@40 {
+		compatible = "ti,ina219";
+		reg = <0x40>;
+		shunt-resistor = <10000>;
+	};
+
+	temperature-sensor@4f {
+		compatible = "ti,tmp75c";
+		reg = <0x4f>;
+	};
+
+	carrier_eeprom: eeprom@57 {
+		compatible = "st,24c02", "atmel,24c02";
+		reg = <0x57>;
+		pagesize = <16>;
+	};
+};
+
+/* Verdin I2C_4_CSI */
+&lpi2c5 {
+	status = "okay";
+};
+
+/* Verdin UART_3, used as the Linux console */
+&lpuart1 {
+	status = "okay";
+};
+
+/* Verdin UART_4 */
+&lpuart2 {
+	status = "okay";
+};
+
+/* Verdin UART_1, connector X50 through RS485 transceiver */
+&lpuart7 {
+	rs485-rts-active-low;
+	rs485-rx-during-tx;
+	linux,rs485-enabled-at-boot-time;
+
+	status = "okay";
+};
+
+/* Verdin UART_2 */
+&lpuart8 {
+	status = "okay";
+};
+
+&netc_emdio {
+	ethphy2: ethernet-phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_eth2_rgmii_int>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+		micrel,led-mode = <0>;
+	};
+};
+
+/* Verdin PCIE_1 */
+&pcie0 {
+	status = "okay";
+};
+
+/* Verdin I2S_1 */
+&sai3 {
+	status = "okay";
+};
+
+/* Verdin PWM_1 */
+&tpm4 {
+	status = "okay";
+};
+
+/* Verdin PWM_2 */
+&tpm5 {
+	status = "okay";
+};
+
+/* Verdin PWM_3_DSI */
+&tpm6 {
+	status = "okay";
+};
+
+/* Verdin USB_1 */
+&usb2 {
+	status = "okay";
+};
+
+/* Verdin USB_2 */
+&usb3 {
+	fsl,permanently-attached;
+
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+/* Verdin SD_1 */
+&usdhc2 {
+	status = "okay";
+};
+
+/* Verdin CTRL_WAKE1_MICO# */
+&verdin_gpio_keys {
+	status = "okay";
+};
arch/arm/dts/imx95-verdin-wifi-dev-u-boot.dtsi new file +112 -0

112 lines not on this page · raw message

arch/arm/dts/imx95-verdin-wifi-dev.dts new file +21 -0
new file mode 100644
index 000000000000..345d37247025
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) Toradex
+ *
+ * https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx95
+ * https://www.toradex.com/products/carrier-board/verdin-development-board-kit
+ */
+
+/dts-v1/;
+
+#include "imx95-verdin.dtsi"
+#include "imx95-verdin-wifi.dtsi"
+#include "imx95-verdin-dev.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX95 WB on Verdin Development Board";
+	compatible = "toradex,verdin-imx95-wifi-dev",
+		     "toradex,verdin-imx95-wifi",
+		     "toradex,verdin-imx95",
+		     "fsl,imx95";
+};
arch/arm/dts/imx95-verdin-wifi.dtsi new file +50 -0

50 lines not on this page · raw message

arch/arm/dts/imx95-verdin.dtsi new file +1172 -0

1,172 lines not on this page · raw message

arch/arm/mach-imx/imx9/Kconfig +5 -0
index 2308457df23e..27e887213a8c 100644
@@ -171,6 +171,10 @@ config TARGET_TORADEX_SMARC_IMX95
 	select IMX95
 	imply OF_UPSTREAM
 
+config TARGET_VERDIN_IMX95
+	bool "Support Toradex Verdin iMX95 module"
+	select IMX95
+
 config TARGET_IMX952_EVK
 	bool "imx952_evk"
 	select IMX_SM_CPU
@@ -195,6 +199,7 @@ source "board/variscite/imx93_var_som/Kconfig"
 source "board/nxp/imx94_evk/Kconfig"
 source "board/nxp/imx95_evk/Kconfig"
 source "board/toradex/smarc-imx95/Kconfig"
+source "board/toradex/verdin-imx95/Kconfig"
 source "board/nxp/imx952_evk/Kconfig"
 
 endif
board/toradex/verdin-imx95/Kconfig new file +36 -0
new file mode 100644
index 000000000000..ef4206c343c0
@@ -0,0 +1,36 @@
+if TARGET_VERDIN_IMX95
+
+config SYS_BOARD
+	default "verdin-imx95"
+
+config SYS_VENDOR
+	default "toradex"
+
+config SYS_CONFIG_NAME
+	default "verdin-imx95"
+
+config TDX_CFG_BLOCK
+	default y
+
+config TDX_CFG_BLOCK_2ND_ETHADDR
+	default y
+
+config TDX_CFG_BLOCK_DEV
+	default "0"
+
+# Toradex config block in eMMC, at the end of 1st "boot sector"
+config TDX_CFG_BLOCK_OFFSET
+	default "-512"
+
+config TDX_CFG_BLOCK_PART
+	default "1"
+
+config TDX_HAVE_EEPROM_EXTRA
+	default y
+
+config TDX_HAVE_MMC
+	default y
+
+source "board/toradex/common/Kconfig"
+
+endif
board/toradex/verdin-imx95/MAINTAINERS new file +13 -0
new file mode 100644
index 000000000000..d19ee3ebfe5d
@@ -0,0 +1,13 @@
+Verdin iMX95
+F:	arch/arm/dts/imx95-verdin.dtsi
+F:	arch/arm/dts/imx95-verdin-dev.dtsi
+F:	arch/arm/dts/imx95-verdin-wifi.dtsi
+F:	arch/arm/dts/imx95-verdin-wifi-dev.dts
+F:	arch/arm/dts/imx95-verdin-wifi-dev-u-boot.dtsi
+F:	board/toradex/verdin-imx95/
+F:	configs/verdin-imx95_defconfig
+F:	doc/board/toradex/verdin-imx95.rst
+F:	include/configs/verdin-imx95.h
+M:	Francesco Dolcini <[email protected]>
+S:	Maintained
+W:	https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx95
board/toradex/verdin-imx95/Makefile new file +8 -0
new file mode 100644
index 000000000000..bc1b6811bbec
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+# Copyright (c) Toradex
+
+obj-y += verdin-imx95.o
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+endif
board/toradex/verdin-imx95/spl.c new file +75 -0

75 lines not on this page · raw message

board/toradex/verdin-imx95/verdin-imx95.c new file +79 -0

79 lines not on this page · raw message

board/toradex/verdin-imx95/verdin-imx95.env new file +20 -0
new file mode 100644
index 000000000000..5ca6cb18aaaa
@@ -0,0 +1,20 @@
+boot_scripts=boot.scr
+boot_script_dhcp=boot.scr
+boot_targets=mmc1 mmc0 dhcp
+console=ttyLP2
+fdt_board=dev
+fdt_addr=0x9c400000
+fdt_addr_r=0x9c400000
+kernel_addr_r=CONFIG_SYS_LOAD_ADDR
+kernel_comp_addr_r=0x94400000
+kernel_comp_size=0x8000000
+ramdisk_addr_r=0x9c800000
+scriptaddr=0x9c600000
+
+update_uboot=
+		askenv confirm Did you load flash.bin (y/N)?;
+		if test "$confirm" = y; then
+			setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt
+			${blkcnt} / 0x200; mmc dev 0 1; mmc write ${loadaddr} 0x0
+			${blkcnt};
+		fi
configs/verdin-imx95_defconfig new file +183 -0

183 lines not on this page · raw message

doc/board/toradex/index.rst +1 -0
index 27f059542e6a..2a45bde6991a 100644
@@ -16,3 +16,4 @@ Toradex
    verdin-am62p
    verdin-imx8mm
    verdin-imx8mp
+   verdin-imx95
doc/board/toradex/verdin-imx95.rst new file +171 -0

171 lines not on this page · raw message

include/configs/verdin-imx95.h new file +27 -0
new file mode 100644
index 000000000000..30eb2e01460b
@@ -0,0 +1,27 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/* Copyright (c) Toradex */
+
+#ifndef __VERDIN_IMX95_H
+#define __VERDIN_IMX95_H
+
+#include <linux/sizes.h>
+#include <asm/arch/imx-regs.h>
+
+/* For 32GB modules: 2GB from 0x80000000..0xffffffff, 30GB above.
+ * Actual size is determined at runtime.
+ */
+#define SZ_30G	_AC(0x780000000, ULL)
+
+/* The first 256MB of SDRAM is reserved for firmware (Cortex M7) */
+#define PHYS_SDRAM_FW_RSVD	SZ_256M
+#define CFG_SYS_INIT_RAM_ADDR	PHYS_SDRAM
+#define CFG_SYS_INIT_RAM_SIZE	SZ_2M
+
+#define CFG_SYS_SDRAM_BASE	PHYS_SDRAM
+#define PHYS_SDRAM		(0x80000000 + PHYS_SDRAM_FW_RSVD)
+#define PHYS_SDRAM_SIZE		(SZ_2G - PHYS_SDRAM_FW_RSVD)
+#define PHYS_SDRAM_2_SIZE	SZ_30G
+
+#define WDOG_BASE_ADDR		WDG3_BASE_ADDR
+
+#endif
Signature · 1 line
2.43.0
#5 lore raw

PATCH v2 3/3 toradex: tdx-cfg-block: add verdin imx95 0226, 0227 and 0228 pid4

In reply to Emanuele Ghidoli

From: Emanuele Ghidoli <[email protected]>

Add these new PID4 to config block handling:
- 0226 Verdin iMX95 Hexa 4GB WB IT
- 0227 Verdin iMX95 Hexa 4GB ET
- 0228 Verdin iMX95 Hexa 16GB IT

---
 board/toradex/common/tdx-cfg-block.c      | 3 +++
 board/toradex/common/tdx-cfg-block.h      | 3 +++
 board/toradex/verdin-imx95/verdin-imx95.c | 3 ++-
 3 files changed, 8 insertions(+), 1 deletion(-)
board/toradex/common/tdx-cfg-block.c +3 -0
index c8c10742103b..896a0d3bd126 100644
@@ -187,6 +187,9 @@ const struct toradex_som toradex_modules[] = {
 	{ OSM_IMX91S_2GB_IT,                     "OSM iMX91 Solo 2GB IT",                TARGET_IS_ENABLED(TORADEX_OSM_IMX91)    },
 	{ VERDIN_AM62D_1G_ET_GPU_NODSI,          "Verdin AM62 Dual 1GB ET",              TARGET_IS_ENABLED(VERDIN_AM62_A53)      },
 	{ AQUILA_TDA4O_16GB_IT,                  "Aquila TDA4 Octa 16GB IT",             TARGET_IS_ENABLED(AQUILA_AM69_A72)      },
+	{ VERDIN_IMX95H_4G_WB_IT,                "Verdin iMX95 Hexa 4GB WB IT",          TARGET_IS_ENABLED(VERDIN_IMX95)         },
+	{ VERDIN_IMX95H_4G_ET,                   "Verdin iMX95 Hexa 4GB ET",             TARGET_IS_ENABLED(VERDIN_IMX95)         },
+	{ VERDIN_IMX95H_16G_IT,                  "Verdin iMX95 Hexa 16GB IT",            TARGET_IS_ENABLED(VERDIN_IMX95)         },
 };
 
 struct pid4list {
board/toradex/common/tdx-cfg-block.h +3 -0
index 3022ef615ad8..9a96bddfbe17 100644
@@ -150,6 +150,9 @@ enum {
 	OSM_IMX91S_2GB_IT, /* 220 */
 	VERDIN_AM62D_1G_ET_GPU_NODSI,
 	AQUILA_TDA4O_16GB_IT = 223,
+	VERDIN_IMX95H_4G_WB_IT = 226,
+	VERDIN_IMX95H_4G_ET,
+	VERDIN_IMX95H_16G_IT,
 };
 
 enum {
board/toradex/verdin-imx95/verdin-imx95.c +2 -1
index 36e41ec3ad4a..60c1dbb5e294 100644
@@ -27,7 +27,8 @@ static void select_dt_from_module_version(void)
 		 * module with Wi-Fi/Bluetooth make sure we use the -wifi
 		 * device tree.
 		 */
-		is_wifi = (tdx_hw_tag.prodid == VERDIN_IMX95H_8G_WIFI_BT_IT);
+		is_wifi = (tdx_hw_tag.prodid == VERDIN_IMX95H_8G_WIFI_BT_IT) ||
+			  (tdx_hw_tag.prodid == VERDIN_IMX95H_4G_WB_IT);
 	}
 
 	if (is_wifi)
Signature · 1 line
2.43.0
Acked-by on the v2 series
#7 lore raw
In reply to Emanuele Ghidoli
Quoted 4 lines · Emanuele Ghidoli

From: Emanuele Ghidoli <[email protected]>

This series adds initial U-Boot support for the Toradex Verdin iMX95.

Quoted 8 lines

It also introduces a new RAM-size probing helper based on alias checks. On Verdin iMX95, the first DDR region is reserved for Cortex-M7 firmware and the get_ram_size() could not be used to detect the actual RAM size. Using explicit probe/alias pairs provides reliable size detection for the supported memory variants.

The board DT is currently aligned with linux-next. Once the board DTS is in mainline Linux, we'll move to OF_UPSTREAM.