USB: serial: mos7720: fix actual baud rate not reported back to TTY
Subsystems (2)
PATCH 1/1 USB: serial: mos7720: fix actual baud rate not reported back to TTY
The calc_baud_rate_divisor() function computes a divisor from the requested baud rate using integer arithmetic, which means the actual hardware baud rate may differ from the requested one. Previously this rounded value was never propagated back to the TTY layer, so tty_encode_baud_rate() was called with the requested rate rather than the actual one.
Change baudrate parameters in calc_baud_rate_divisor() and send_cmd_write_baud_rate() to pointers so the actual resulting baud rate can be written back to the caller. Update *baudrate with the computed value (230400 / custom) after divisor calculation.
In change_port_settings(), pass &baud to send_cmd_write_baud_rate() and guard tty_encode_baud_rate() with a status check, so the TTY is only updated on success and receives the true hardware baud rate.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
--- drivers/usb/serial/mos7720.c | 29 ++++++++++++++--------------- 1 file changed, 14 insertions(+), 15 deletions(-)
drivers/usb/serial/mos7720.c +14 -15
@@ -1264,9 +1264,9 @@ static const struct divisor_table_entry divisor_table[] = {/***************************************************************************** * calc_baud_rate_divisor * this function calculates the proper baud rate divisor for the specified -* baud rate. +* baud rate and updates the baudrate parameter with the actual value. *****************************************************************************/ -static int calc_baud_rate_divisor (struct usb_serial_port *port,int baudrate,int *divisor) +static int calc_baud_rate_divisor (struct usb_serial_port *port,int *baudrate,int *divisor) {int i;__u16 custom;
@@ -1274,10 +1274,10 @@ static int calc_baud_rate_divisor(struct usb_serial_port *port, int baudrate, in__u16 round; -dev_dbg (&port->dev,"%s - %d\n" , __func__, baudrate); +dev_dbg (&port->dev,"%s - %d\n" , __func__, *baudrate);for (i =0 ; i <ARRAY_SIZE (divisor_table); i++) { -if (divisor_table[i].baudrate == baudrate) { +if (divisor_table[i].baudrate == *baudrate) { *divisor = divisor_table[i].divisor;return 0 ; }
@@ -1285,18 +1285,19 @@ static int calc_baud_rate_divisor(struct usb_serial_port *port, int baudrate, in/* After trying for all the standard baud rates * * Try calculating the divisor for this baud rate */ -if (baudrate >75 && baudrate <230400 ) { +if (*baudrate >75 && *baudrate <230400 ) {/* get the divisor */ - custom = (__u16)(230400L / baudrate); + custom = (__u16)(230400L / *baudrate);/* Check for round off */ - round1 = (__u16)(2304000L / baudrate); + round1 = (__u16)(2304000L / *baudrate); round = (__u16)(round1 - (custom *10 ));if (round >4 ) custom++; *divisor = custom; + *baudrate =230400L / custom; -dev_dbg (&port->dev,"Baud %d = %d\n" , baudrate, custom); +dev_dbg (&port->dev,"Baud %d = %d\n" , *baudrate, custom);return 0 ; }
@@ -1307,10 +1308,10 @@ static int calc_baud_rate_divisor(struct usb_serial_port *port, int baudrate, in/* * send_cmd_write_baud_rate * this function sends the proper command to change the baud rate of the -* specified port. +* specified port and updates the baudrate parameter with the actual value. */ static int send_cmd_write_baud_rate (struct moschip_port *mos7720_port, -int baudrate) +int *baudrate) {struct usb_serial_port *port;struct usb_serial *serial;
@@ -1325,7 +1326,7 @@ static int send_cmd_write_baud_rate(struct moschip_port *mos7720_port, serial = port->serial; number = port->port_number; -dev_dbg (&port->dev,"%s - baud = %d\n" , __func__, baudrate); +dev_dbg (&port->dev,"%s - baud = %d\n" , __func__, *baudrate);/* Calculate the Divisor */ status =calc_baud_rate_divisor (port, baudrate, &divisor);
@@ -1474,10 +1475,8 @@ static void change_port_settings(struct tty_struct *tty, }dev_dbg (&port->dev,"%s - baud rate = %d\n" , __func__, baud); - status =send_cmd_write_baud_rate (mos7720_port, baud); -/* FIXME: needs to write actual resulting baud back not just -blindly do so */ -if (cflag &CBAUD ) + status =send_cmd_write_baud_rate (mos7720_port, &baud); +if (!status && (cflag &CBAUD ))tty_encode_baud_rate (tty, baud, baud);/* Enable Interrupts */ write_mos_reg (serial, port_number,MOS7720_IER ,0x0c );
Signature · 1 line
2.51.0