Skip to contentSkip to conversation

hwmon: (ads7871) Fix endianness and modernize driver

PATCH Applied Tabrez Ahmed 3 participants 9 messages May 1 – May 2 Hardware monitoring

v5 of 6 Applied Latest is v6 →

lore
Share & tools
lore
#0 lore raw

v5 cover hwmon: (ads7871) Fix endianness and modernize driver

This series addresses several issues in the ads7871 driver. It fixes an architecture-dependent endianness bug in the 16-bit register read logic, migrates the driver to the modern hwmon_device_register_with_info() API, and moves the SPI transfer buffer into the driver's private data structure to ensure DMA safety.

Note: I do not have access to the physical ADS7871 hardware. This series has been compile-tested only.

Changes in v5:
- Fixed a bisectability issue where the <linux/unaligned.h> include modernization was accidentally squashed into Patch 3 instead of Patch 1.
- Ensured the 1-byte SPI command write in ads7871_read_reg16() uses a strictly typed 'u8' variable to prevent a Big-Endian pointer hazard.

Changes in v4:
- Patch 1: Refactored 16-bit register reads to use a dedicated 'u8' transmit variable, eliminating a 32-bit pointer endianness hazard.

Changes in v3:
- Added Patch 1 to fix the pre-existing endianness bug in 16-bit reads.
- Fixed multiple formatting and alignment issues caught by checkpatch --strict, as requested by Guenter Roeck.
- Added "While at it, fix checkpatch violations" to Patch 2 commit message.

Tabrez Ahmed (3):
hwmon: (ads7871) Fix endianness bug in 16-bit register reads
hwmon: (ads7871) Convert to hwmon_device_register_with_info
hwmon: (ads7871) Use DMA-safe buffer for SPI writes

 drivers/hwmon/ads7871.c | 122 +++++++++++++++++++++++-----------------
 1 file changed, 71 insertions(+), 51 deletions(-)
Signature · 1 line
2.43.0
#1 lore raw

PATCH v5 1/3 hwmon: (ads7871) Fix endianness bug in 16-bit register reads

The ads7871_read_reg16() function relies on spi_w8r16() to read the 16-bit sensor output. The ADS7871 device transmits the Least Significant Byte (LSB) first.

On Little-Endian architectures, spi_w8r16() correctly reconstructs the 16-bit value. However, on Big-Endian architectures, the byte swapping causes the first received byte (LSB) to be placed in the most significant byte of the u16, resulting in corrupted voltage readings.

Replace spi_w8r16() with a manual spi_write_then_read() into a byte array, and safely reconstruct the integer using get_unaligned_le16() to ensure correct behavior across all architectures. Additionally, use a u8 variable for the command byte to ensure the correct instruction is transmitted on Big-Endian systems.

---
 drivers/hwmon/ads7871.c | 14 +++++++++++---
 1 file changed, 11 insertions(+), 3 deletions(-)
drivers/hwmon/ads7871.c +11 -3
index 9bfdf9e6bcd77..d77eff430935b 100644
@@ -59,9 +59,9 @@
 #include <linux/hwmon-sysfs.h>
 #include <linux/err.h>
 #include <linux/delay.h>
+#include <linux/unaligned.h>
 
 #define DEVICE_NAME	"ads7871"
-
 struct ads7871_data {
 	struct spi_device *spi;
 };
@@ -77,9 +77,17 @@ static int ads7871_read_reg8(struct spi_device *spi, int reg)
 static int ads7871_read_reg16(struct spi_device *spi, int reg)
 {
 	int ret;
+	u8 tx_cmd;
+	u8 rx_buf[2];
+
 	reg = reg | INST_READ_BM | INST_16BIT_BM;
-	ret = spi_w8r16(spi, reg);
-	return ret;
+	tx_cmd = reg;
+
+	ret = spi_write_then_read(spi, &tx_cmd, 1, rx_buf, 2);
+	if (ret < 0)
+		return ret;
+
+	return get_unaligned_le16(rx_buf);
 }
 
 static int ads7871_write_reg8(struct spi_device *spi, int reg, u8 val)
Signature · 1 line
2.43.0
maintainer
#2 lore raw

Re: [PATCH v5 1/3] hwmon: (ads7871) Fix endianness bug in 16-bit register reads

Quoted 38 lines · Tabrez Ahmed

The ads7871_read_reg16() function relies on spi_w8r16() to read the 16-bit sensor output. The ADS7871 device transmits the Least Significant Byte (LSB) first.

On Little-Endian architectures, spi_w8r16() correctly reconstructs the 16-bit value. However, on Big-Endian architectures, the byte swapping causes the first received byte (LSB) to be placed in the most significant byte of the u16, resulting in corrupted voltage readings.

Replace spi_w8r16() with a manual spi_write_then_read() into a byte array, and safely reconstruct the integer using get_unaligned_le16() to ensure correct behavior across all architectures. Additionally, use a u8 variable for the command byte to ensure the correct instruction is transmitted on Big-Endian systems.

---
  drivers/hwmon/ads7871.c | 14 +++++++++++---
  1 file changed, 11 insertions(+), 3 deletions(-)
drivers/hwmon/ads7871.c +1 -1
index 9bfdf9e6bcd77..d77eff430935b 100644
@@ -59,9 +59,9 @@
  #include <linux/hwmon-sysfs.h>
  #include <linux/err.h>
  #include <linux/delay.h>
+#include <linux/unaligned.h>
 
  #define DEVICE_NAME	"ads7871"
-
  struct ads7871_data {
  	struct spi_device *spi;
  };

drivers/hwmon/ads7871.c static int ads7871_read_reg8(struct spi_device *spi, int reg) · line 84

Quoted 10 lines
drivers/hwmon/ads7871.c +4 -2
@@ -77,9 +77,17 @@ static int ads7871_read_reg8(struct spi_device *spi, int reg)
  static int ads7871_read_reg16(struct spi_device *spi, int reg)
  {
  	int ret;
+	u8 tx_cmd;
+	u8 rx_buf[2];
+
  	reg = reg | INST_READ_BM | INST_16BIT_BM;
-	ret = spi_w8r16(spi, reg);
-	return ret;
+	tx_cmd = reg;

This can be combined into

	tx_cmd = reg | INST_READ_BM | INST_16BIT_BM;

Thanks,
Guenter

Quoted 9 lines
drivers/hwmon/ads7871.c +6 -0
+
+	ret = spi_write_then_read(spi, &tx_cmd, 1, rx_buf, 2);
+	if (ret < 0)
+		return ret;
+
+	return get_unaligned_le16(rx_buf);
  }
 
  static int ads7871_write_reg8(struct spi_device *spi, int reg, u8 val)
#3 lore raw

Re: [PATCH v5 1/3] hwmon: (ads7871) Fix endianness bug in 16-bit register reads

In reply to Tabrez Ahmed
Quoted 38 lines · On Fri, 1 May 2026 08:05:28 +0530 Tabrez Ahmed <[email protected]> wrote:

The ads7871_read_reg16() function relies on spi_w8r16() to read the 16-bit sensor output. The ADS7871 device transmits the Least Significant Byte (LSB) first.

On Little-Endian architectures, spi_w8r16() correctly reconstructs the 16-bit value. However, on Big-Endian architectures, the byte swapping causes the first received byte (LSB) to be placed in the most significant byte of the u16, resulting in corrupted voltage readings.

Replace spi_w8r16() with a manual spi_write_then_read() into a byte array, and safely reconstruct the integer using get_unaligned_le16() to ensure correct behavior across all architectures. Additionally, use a u8 variable for the command byte to ensure the correct instruction is transmitted on Big-Endian systems.

---
 drivers/hwmon/ads7871.c | 14 +++++++++++---
 1 file changed, 11 insertions(+), 3 deletions(-)
drivers/hwmon/ads7871.c +1 -1
index 9bfdf9e6bcd77..d77eff430935b 100644
@@ -59,9 +59,9 @@
 #include <linux/hwmon-sysfs.h>
 #include <linux/err.h>
 #include <linux/delay.h>
+#include <linux/unaligned.h>
 
 #define DEVICE_NAME	"ads7871"
-
 struct ads7871_data {
 	struct spi_device *spi;
 };

drivers/hwmon/ads7871.c static int ads7871_read_reg8(struct spi_device *spi, int reg) · line 82

Quoted 9 lines
drivers/hwmon/ads7871.c +3 -2
@@ -77,9 +77,17 @@ static int ads7871_read_reg8(struct spi_device *spi, int reg)
 static int ads7871_read_reg16(struct spi_device *spi, int reg)
 {
 	int ret;
+	u8 tx_cmd;
+	u8 rx_buf[2];
+
 	reg = reg | INST_READ_BM | INST_16BIT_BM;
-	ret = spi_w8r16(spi, reg);
-	return ret;

Isn't it enough to just byteswap the result? so:

	return le16toh(ret);
The whole thing can be:
	return le16toh(spi_w8r16(spi, reg | INST_READ_BM | INST_16BIT_BM));

(although I suspect sparse bleats and needs an annoying (__force __le16) cast)

-- David

Quoted 10 lines
drivers/hwmon/ads7871.c +7 -0
+	tx_cmd = reg;
+
+	ret = spi_write_then_read(spi, &tx_cmd, 1, rx_buf, 2);
+	if (ret < 0)
+		return ret;
+
+	return get_unaligned_le16(rx_buf);
 }
 
 static int ads7871_write_reg8(struct spi_device *spi, int reg, u8 val)
#4 lore raw

Re: [PATCH v5 1/3] hwmon: (ads7871) Fix endianness bug in 16-bit register reads

Quoted 5 lines · David Laight

Isn't it enough to just byteswap the result? so:

	return le16toh(ret);
The whole thing can be:
	return le16toh(spi_w8r16(spi, reg | INST_READ_BM | INST_16BIT_BM));

(although I suspect sparse bleats and needs an annoying (__force __le16) cast)

Hi David,

Good point, spi_w8r16() is definitely cleaner and cuts out the buffer allocations entirely.

I tried the one-liner approach, but le16toh caused a build error because it's not available in the kernel headers. I will swap it for le16_to_cpu in the final patch.

I'm going to split the implementation slightly in v6 to catch negative error codes before the conversion and to match the bitwise assignment style used in the rest of this driver:

static int ads7871_read_reg16(struct spi_device *spi, int reg)

{
	int ret;

	reg = reg | INST_READ_BM | INST_16BIT_BM;
	ret = spi_w8r16(spi, reg);
	if (ret < 0)
		return ret;

	return le16_to_cpu((__force __le16)ret);
}

Guenter this also pulls in your suggestion to combine the bitwise flags.

I'll get v6 out shortly.

Thanks,
Tabrez

maintainer
#5 lore raw

Re: [PATCH v5 1/3] hwmon: (ads7871) Fix endianness bug in 16-bit register reads

In reply to David Laight
Quoted 52 lines · David Laight
Quoted 38 lines · On Fri, 1 May 2026 08:05:28 +0530 Tabrez Ahmed <[email protected]> wrote:

The ads7871_read_reg16() function relies on spi_w8r16() to read the 16-bit sensor output. The ADS7871 device transmits the Least Significant Byte (LSB) first.

On Little-Endian architectures, spi_w8r16() correctly reconstructs the 16-bit value. However, on Big-Endian architectures, the byte swapping causes the first received byte (LSB) to be placed in the most significant byte of the u16, resulting in corrupted voltage readings.

Replace spi_w8r16() with a manual spi_write_then_read() into a byte array, and safely reconstruct the integer using get_unaligned_le16() to ensure correct behavior across all architectures. Additionally, use a u8 variable for the command byte to ensure the correct instruction is transmitted on Big-Endian systems.

---
  drivers/hwmon/ads7871.c | 14 +++++++++++---
  1 file changed, 11 insertions(+), 3 deletions(-)
drivers/hwmon/ads7871.c +1 -1
index 9bfdf9e6bcd77..d77eff430935b 100644
@@ -59,9 +59,9 @@
  #include <linux/hwmon-sysfs.h>
  #include <linux/err.h>
  #include <linux/delay.h>
+#include <linux/unaligned.h>
 
  #define DEVICE_NAME	"ads7871"
-
  struct ads7871_data {
  	struct spi_device *spi;
  };

drivers/hwmon/ads7871.c static int ads7871_read_reg8(struct spi_device *spi, int reg) · line 82

Quoted 9 lines
drivers/hwmon/ads7871.c +3 -2
@@ -77,9 +77,17 @@ static int ads7871_read_reg8(struct spi_device *spi, int reg)
  static int ads7871_read_reg16(struct spi_device *spi, int reg)
  {
  	int ret;
+	u8 tx_cmd;
+	u8 rx_buf[2];
+
  	reg = reg | INST_READ_BM | INST_16BIT_BM;
-	ret = spi_w8r16(spi, reg);
-	return ret;

Isn't it enough to just byteswap the result? so:

Quoted 3 lines
	return le16toh(ret);
The whole thing can be:
	return le16toh(spi_w8r16(spi, reg | INST_READ_BM | INST_16BIT_BM));

This would convert error codes to some random value.

Guenter

maintainer Applied
#6 lore raw

Re: [PATCH v5 1/3] hwmon: (ads7871) Fix endianness bug in 16-bit register reads

In reply to Tabrez Ahmed
Quoted 15 lines · Tabrez Ahmed

The ads7871_read_reg16() function relies on spi_w8r16() to read the 16-bit sensor output. The ADS7871 device transmits the Least Significant Byte (LSB) first.

On Little-Endian architectures, spi_w8r16() correctly reconstructs the 16-bit value. However, on Big-Endian architectures, the byte swapping causes the first received byte (LSB) to be placed in the most significant byte of the u16, resulting in corrupted voltage readings.

Replace spi_w8r16() with a manual spi_write_then_read() into a byte array, and safely reconstruct the integer using get_unaligned_le16() to ensure correct behavior across all architectures. Additionally, use a u8 variable for the command byte to ensure the correct instruction is transmitted on Big-Endian systems.

Quoted 3 lines

Applied.

Thanks,
Guenter

#7 lore raw

PATCH v5 2/3 hwmon: (ads7871) Convert to hwmon_device_register_with_info

In reply to Tabrez Ahmed

Convert the ads7871 driver from the legacy hwmon_device_register() to the modern hwmon_device_register_with_info() API. This migration simplifies the driver by using the structured hwmon_channel_info approach and prepares the codebase for the transition to a shared DMA-safe buffer. While at it, fix checkpatch violations.

---
 drivers/hwmon/ads7871.c | 75 ++++++++++++++++++++++-------------------
 1 file changed, 40 insertions(+), 35 deletions(-)
drivers/hwmon/ads7871.c +40 -35
index d77eff430935b..75485a2c16b0b 100644
@@ -56,7 +56,6 @@
 #include <linux/init.h>
 #include <linux/spi/spi.h>
 #include <linux/hwmon.h>
-#include <linux/hwmon-sysfs.h>
 #include <linux/err.h>
 #include <linux/delay.h>
 #include <linux/unaligned.h>
@@ -66,6 +65,16 @@ struct ads7871_data {
 	struct spi_device *spi;
 };
 
+static umode_t ads7871_is_visible(const void *data,
+				  enum hwmon_sensor_types type,
+				  u32 attr, int channel)
+{
+	if (type == hwmon_in && attr == hwmon_in_input)
+		return 0444;
+
+	return 0;
+}
+
 static int ads7871_read_reg8(struct spi_device *spi, int reg)
 {
 	int ret;
@@ -93,19 +102,20 @@ static int ads7871_read_reg16(struct spi_device *spi, int reg)
 static int ads7871_write_reg8(struct spi_device *spi, int reg, u8 val)
 {
 	u8 tmp[2] = {reg, val};
+
 	return spi_write(spi, tmp, sizeof(tmp));
 }
 
-static ssize_t voltage_show(struct device *dev, struct device_attribute *da,
-			    char *buf)
+static int ads7871_read(struct device *dev, enum hwmon_sensor_types type,
+			u32 attr, int channel, long *val)
 {
 	struct ads7871_data *pdata = dev_get_drvdata(dev);
 	struct spi_device *spi = pdata->spi;
-	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
-	int ret, val, i = 0;
-	uint8_t channel, mux_cnv;
+	int ret, raw_val, i = 0;
+	u8 mux_cnv;
 
-	channel = attr->index;
+	if (type != hwmon_in || attr != hwmon_in_input)
+		return -EOPNOTSUPP;
 	/*
 	 * TODO: add support for conversions
 	 * other than single ended with a gain of 1
@@ -135,39 +145,34 @@ static ssize_t voltage_show(struct device *dev, struct device_attribute *da,
 	}
 
 	if (mux_cnv == 0) {
-		val = ads7871_read_reg16(spi, REG_LS_BYTE);
-		if (val < 0)
-			return val;
+		raw_val = ads7871_read_reg16(spi, REG_LS_BYTE);
+		if (raw_val < 0)
+			return raw_val;
+
 		/*result in volts*10000 = (val/8192)*2.5*10000*/
-		val = ((val >> 2) * 25000) / 8192;
-		return sysfs_emit(buf, "%d\n", val);
+		*val = ((raw_val >> 2) * 25000) / 8192;
+		return 0;
 	}
 
 	return -ETIMEDOUT;
 }
 
-static SENSOR_DEVICE_ATTR_RO(in0_input, voltage, 0);
-static SENSOR_DEVICE_ATTR_RO(in1_input, voltage, 1);
-static SENSOR_DEVICE_ATTR_RO(in2_input, voltage, 2);
-static SENSOR_DEVICE_ATTR_RO(in3_input, voltage, 3);
-static SENSOR_DEVICE_ATTR_RO(in4_input, voltage, 4);
-static SENSOR_DEVICE_ATTR_RO(in5_input, voltage, 5);
-static SENSOR_DEVICE_ATTR_RO(in6_input, voltage, 6);
-static SENSOR_DEVICE_ATTR_RO(in7_input, voltage, 7);
-
-static struct attribute *ads7871_attrs[] = {
-	&sensor_dev_attr_in0_input.dev_attr.attr,
-	&sensor_dev_attr_in1_input.dev_attr.attr,
-	&sensor_dev_attr_in2_input.dev_attr.attr,
-	&sensor_dev_attr_in3_input.dev_attr.attr,
-	&sensor_dev_attr_in4_input.dev_attr.attr,
-	&sensor_dev_attr_in5_input.dev_attr.attr,
-	&sensor_dev_attr_in6_input.dev_attr.attr,
-	&sensor_dev_attr_in7_input.dev_attr.attr,
+static const struct hwmon_channel_info * const ads7871_info[] = {
+	HWMON_CHANNEL_INFO(in,
+			   HWMON_I_INPUT, HWMON_I_INPUT, HWMON_I_INPUT, HWMON_I_INPUT,
+			   HWMON_I_INPUT, HWMON_I_INPUT, HWMON_I_INPUT, HWMON_I_INPUT),
 	NULL
 };
 
-ATTRIBUTE_GROUPS(ads7871);
+static const struct hwmon_ops ads7871_hwmon_ops = {
+	.is_visible = ads7871_is_visible,
+	.read = ads7871_read,
+};
+
+static const struct hwmon_chip_info ads7871_chip_info = {
+	.ops = &ads7871_hwmon_ops,
+	.info = ads7871_info,
+};
 
 static int ads7871_probe(struct spi_device *spi)
 {
@@ -202,10 +207,10 @@ static int ads7871_probe(struct spi_device *spi)
 		return -ENOMEM;
 
 	pdata->spi = spi;
-
-	hwmon_dev = devm_hwmon_device_register_with_groups(dev, spi->modalias,
-							   pdata,
-							   ads7871_groups);
+	hwmon_dev = devm_hwmon_device_register_with_info(dev, spi->modalias,
+							 pdata,
+							 &ads7871_chip_info,
+							 NULL);
 	return PTR_ERR_OR_ZERO(hwmon_dev);
 }
 
Signature · 1 line
2.43.0
#8 lore raw

PATCH v5 3/3 hwmon: (ads7871) Use DMA-safe buffer for SPI writes

In reply to Tabrez Ahmed

The driver currently passes a stack-allocated buffer to spi_write(), which is incompatible with DMA on systems with CONFIG_VMAP_STACK enabled.

Move the transfer buffer into the driver's private data structure to ensure it is DMA-safe. Since this shared buffer now requires serialization, this change depends on the previous commit which migrated the driver to the hwmon 'with_info' API.

While moving the logic, also:
- Corrected the sign extension for 14-bit data by casting to s16.
- Scaled the output to millivolts (2500mV full scale
) to comply with the hwmon ABI.

---
 drivers/hwmon/ads7871.c | 35 +++++++++++++++++++++--------------
 1 file changed, 21 insertions(+), 14 deletions(-)
drivers/hwmon/ads7871.c +21 -14
index 75485a2c16b0b..cbb9a88229c50 100644
@@ -63,6 +63,7 @@
 #define DEVICE_NAME	"ads7871"
 struct ads7871_data {
 	struct spi_device *spi;
+	u8 tx_buf[2] ____cacheline_aligned;
 };
 
 static umode_t ads7871_is_visible(const void *data,
@@ -99,11 +100,12 @@ static int ads7871_read_reg16(struct spi_device *spi, int reg)
 	return get_unaligned_le16(rx_buf);
 }
 
-static int ads7871_write_reg8(struct spi_device *spi, int reg, u8 val)
+static int ads7871_write_reg8(struct ads7871_data *pdata, int reg, u8 val)
 {
-	u8 tmp[2] = {reg, val};
+	pdata->tx_buf[0] = reg;
+	pdata->tx_buf[1] = val;
 
-	return spi_write(spi, tmp, sizeof(tmp));
+	return spi_write(pdata->spi, pdata->tx_buf, 2);
 }
 
 static int ads7871_read(struct device *dev, enum hwmon_sensor_types type,
@@ -122,7 +124,7 @@ static int ads7871_read(struct device *dev, enum hwmon_sensor_types type,
 	 */
 	/*MUX_M3_BM forces single ended*/
 	/*This is also where the gain of the PGA would be set*/
-	ret = ads7871_write_reg8(spi, REG_GAIN_MUX,
+	ret = ads7871_write_reg8(pdata, REG_GAIN_MUX,
 				 (MUX_CNV_BM | MUX_M3_BM | channel));
 	if (ret < 0)
 		return ret;
@@ -130,6 +132,7 @@ static int ads7871_read(struct device *dev, enum hwmon_sensor_types type,
 	ret = ads7871_read_reg8(spi, REG_GAIN_MUX);
 	if (ret < 0)
 		return ret;
+
 	mux_cnv = ((ret & MUX_CNV_BM) >> MUX_CNV_BV);
 	/*
 	 * on 400MHz arm9 platform the conversion
@@ -149,8 +152,11 @@ static int ads7871_read(struct device *dev, enum hwmon_sensor_types type,
 		if (raw_val < 0)
 			return raw_val;
 
-		/*result in volts*10000 = (val/8192)*2.5*10000*/
-		*val = ((raw_val >> 2) * 25000) / 8192;
+		/*
+		 * Use (s16) to ensure the sign bit is preserved during the shift.
+		 * Report millivolts (2.5V = 2500mV).
+		 */
+		*val = ((s16)raw_val >> 2) * 2500 / 8192;
 		return 0;
 	}
 
@@ -187,11 +193,17 @@ static int ads7871_probe(struct spi_device *spi)
 	spi->bits_per_word = 8;
 	spi_setup(spi);
 
-	ads7871_write_reg8(spi, REG_SER_CONTROL, 0);
-	ads7871_write_reg8(spi, REG_AD_CONTROL, 0);
+	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata)
+		return -ENOMEM;
+
+	pdata->spi = spi;
+
+	ads7871_write_reg8(pdata, REG_SER_CONTROL, 0);
+	ads7871_write_reg8(pdata, REG_AD_CONTROL, 0);
 
 	val = (OSC_OSCR_BM | OSC_OSCE_BM | OSC_REFE_BM | OSC_BUFE_BM);
-	ads7871_write_reg8(spi, REG_OSC_CONTROL, val);
+	ads7871_write_reg8(pdata, REG_OSC_CONTROL, val);
 	ret = ads7871_read_reg8(spi, REG_OSC_CONTROL);
 
 	dev_dbg(dev, "REG_OSC_CONTROL write:%x, read:%x\n", val, ret);
@@ -202,11 +214,6 @@ static int ads7871_probe(struct spi_device *spi)
 	if (val != ret)
 		return -ENODEV;
 
-	pdata = devm_kzalloc(dev, sizeof(struct ads7871_data), GFP_KERNEL);
-	if (!pdata)
-		return -ENOMEM;
-
-	pdata->spi = spi;
 	hwmon_dev = devm_hwmon_device_register_with_info(dev, spi->modalias,
 							 pdata,
 							 &ads7871_chip_info,
Signature · 1 line
2.43.0