dts: spacemit: set console baud rate on bpif3
Subsystems (3)
PATCH 1/1 dts: spacemit: set console baud rate on bpif3
From: Conor Dooley <[email protected]>
Because the default console's baud rate is not set, defconfig kernels do not have any serial output on this platform. Set the baud rate to 115200, matching what is used by U-Boot etc on this platform.
---
CC: Rob Herring <[email protected]>
CC: Krzysztof Kozlowski <[email protected]>
CC: Conor Dooley <[email protected]>
CC: Yixun Lan <[email protected]>
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
--- arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts +1 -1
@@ -19,7 +19,7 @@ aliases { }; chosen { - stdout-path = "serial0"; + stdout-path = "serial0:115200n8"; }; leds {
Signature · 1 line
2.53.0
Yixun Lan
maintainerHi Conor,
Quoted 18 lines · Conor Dooley
From: Conor Dooley <[email protected]>
Because the default console's baud rate is not set, defconfig kernels do not have any serial output on this platform. Set the baud rate to 115200, matching what is used by U-Boot etc on this platform.
Suggested-by Vivian Wang <[email protected]>Fixes d60d57ab6b2a8 ("riscv: dts: spacemit: add Banana Pi BPI-F3 board device tree")Signed-off-by Conor Dooley <[email protected]>---
CC: Rob Herring <[email protected]>
CC: Krzysztof Kozlowski <[email protected]>
CC: Conor Dooley <[email protected]>
CC: Yixun Lan <[email protected]>
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]
Quoted 2 lines
--- arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts | 2 +-
Looks good to me, but I think the fix should also apply to other boards, so do you want to fix other dts? I'd be fine if you keep it to BPI-F3 only
Quoted 18 lines
1 file changed, 1 insertion(+), 1 deletion(-)arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts +1
-1@@ -19,7 +19,7 @@ aliases { }; chosen { - stdout-path = "serial0"; + stdout-path = "serial0:115200n8"; }; leds {Signature · 1 line
2.53.0
Signature · 1 line
Yixun Lan (dlan)
Quoted 24 lines · Yixun Lan
Hi Conor,
Quoted 18 lines · Conor Dooley
From: Conor Dooley <[email protected]>
Because the default console's baud rate is not set, defconfig kernels do not have any serial output on this platform. Set the baud rate to 115200, matching what is used by U-Boot etc on this platform.
Suggested-by Vivian Wang <[email protected]>Fixes d60d57ab6b2a8 ("riscv: dts: spacemit: add Banana Pi BPI-F3 board device tree")Signed-off-by Conor Dooley <[email protected]>---
CC: Rob Herring <[email protected]>
CC: Krzysztof Kozlowski <[email protected]>
CC: Conor Dooley <[email protected]>
CC: Yixun Lan <[email protected]>
CC: [email protected]
CC: [email protected]
CC: [email protected]
CC: [email protected]Quoted 2 lines
--- arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts | 2 +-
Quoted 2 lines
Looks good to me, but I think the fix should also apply to other boards, so do you want to fix other dts? I'd be fine if you keep it to BPI-F3 only
I don't have any other boards, didn't/don't want to make the change elsewhere where I cannot test it.
Quoted 23 lines
Quoted 20 lines
1 file changed, 1 insertion(+), 1 deletion(-)arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts +1
-1@@ -19,7 +19,7 @@ aliases { }; chosen { - stdout-path = "serial0"; + stdout-path = "serial0:115200n8"; }; leds {Signature · 1 line
2.53.0Signature · 1 line
Yixun Lan (dlan)
Hi Conor,
Quoted 9 lines · Conor Dooley
From: Conor Dooley <[email protected]>
Because the default console's baud rate is not set, defconfig kernels do not have any serial output on this platform. Set the baud rate to 115200, matching what is used by U-Boot etc on this platform.
Suggested-by Vivian Wang <[email protected]>Fixes d60d57ab6b2a8 ("riscv: dts: spacemit: add Banana Pi BPI-F3 board device tree")Signed-off-by Conor Dooley <[email protected]>
Signature · 1 line
Yixun Lan (dlan)
Quoted 5 lines · Conor Dooley
Because the default console's baud rate is not set, defconfig kernels do not have any serial output on this platform. Set the baud rate to 115200, matching what is used by U-Boot etc on this platform.
Applied, thanks!
[1/1] dts: spacemit: set console baud rate on bpif3
https://github.com/spacemit-com/linux/commit/24c12ca43b12c104389d9a159207d0b25779d0af
Best regards,
Signature · 1 line
Yixun Lan <[email protected]>