iio: adc: ti-ads1298: Three driver cleanups
v2 cover iio: adc: ti-ads1298: Three driver cleanups
Three small cleanups to the TI ADS1298 medical ECG ADC driver.
Changes since v1:
- Patch 3/3: Per Mike Looijmans' suggestion, instead of writing only the RESERVED bit to CONFIG2 (which equals the reset default), remove the write entirely. Added Suggested-by tag.
Patches 1/3 and 2/3 are unchanged from v1.
Md Shofiqul Islam (3):
iio: adc: ti-ads1298: Add parentheses around macro parameter
iio: adc: ti-ads1298: Fix incorrect timeout comment
iio: adc: ti-ads1298: Remove unnecessary CONFIG2 write during init
drivers/iio/adc/ti-ads1298.c | 13 ++----------- 1 file changed, 2 insertions(+), 11 deletions(-)
Signature · 1 line
2.54.0.windows.1
PATCH v2 1/3 iio: adc: ti-ads1298: Add parentheses around macro parameter
ADS1298_REG_CHnSET() is missing parentheses around the parameter 'n'. Add them to follow kernel macro coding style and prevent potential operator precedence issues if the argument is an expression.
--- drivers/iio/adc/ti-ads1298.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/iio/adc/ti-ads1298.c +1 -1
@@ -66,7 +66,7 @@#define ADS1298_MASK_CONFIG3_VREF_4V BIT(5)#define ADS1298_REG_LOFF 0x04 -#define ADS1298_REG_CHnSET (n) (0x05 + n) +#define ADS1298_REG_CHnSET (n) (0x05 + (n))#define ADS1298_MASK_CH_PD BIT(7)#define ADS1298_MASK_CH_PGA GENMASK(6, 4)#define ADS1298_MASK_CH_MUX GENMASK(2, 0)
Signature · 1 line
2.54.0.windows.1
Jonathan Cameron
maintainerRe: [PATCH v2 1/3] iio: adc: ti-ads1298: Add parentheses around macro parameter
Quoted 5 lines · On Thu, 7 May 2026 13:51:26 +0300 Md Shofiqul Islam <[email protected]>…
ADS1298_REG_CHnSET()is missing parentheses around the parameter 'n'. Add them to follow kernel macro coding style and prevent potential operator precedence issues if the argument is an expression.Signed-off-by Md Shofiqul Islam <[email protected]>
Hi.
You should have picked up Mike's tag for v2.
Maybe he'll give it again - if not if everything else is fine I'll sort this out whilst applying.
Thanks,
Jonathan
Quoted 17 lines
--- drivers/iio/adc/ti-ads1298.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/iio/adc/ti-ads1298.c +1
-1@@ -66,7 +66,7 @@#define ADS1298_MASK_CONFIG3_VREF_4V BIT(5)#define ADS1298_REG_LOFF 0x04 -#define ADS1298_REG_CHnSET (n) (0x05 + n) +#define ADS1298_REG_CHnSET (n) (0x05 + (n))#define ADS1298_MASK_CH_PD BIT(7)#define ADS1298_MASK_CH_PGA GENMASK(6, 4)#define ADS1298_MASK_CH_MUX GENMASK(2, 0)
PATCH v2 2/3 iio: adc: ti-ads1298: Fix incorrect timeout comment
In reply to Md Shofiqul IslamAt the lowest supported data rate of 250Hz, one conversion period is 4ms, not 40ms. Fix the comment to correctly reflect the timing. The 50ms timeout value itself is correct as a conservative margin.
--- drivers/iio/adc/ti-ads1298.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/iio/adc/ti-ads1298.c +1 -1
@@ -210,7 +210,7 @@ static int ads1298_read_one(struct ads1298_private *priv, int chan_index)return ret; } -/* Cannot take longer than 40ms (250Hz) */ +/* Cannot take longer than 4ms at the lowest rate (250Hz) */ ret =wait_for_completion_timeout (&priv->completion,msecs_to_jiffies (50 ));if (!ret)return -ETIMEDOUT ;
Signature · 1 line
2.54.0.windows.1
Jonathan Cameron
maintainerRe: [PATCH v2 2/3] iio: adc: ti-ads1298: Fix incorrect timeout comment
Quoted 5 lines · On Thu, 7 May 2026 13:51:27 +0300 Md Shofiqul Islam <[email protected]>…
At the lowest supported data rate of 250Hz, one conversion period is 4ms, not 40ms. Fix the comment to correctly reflect the timing. The 50ms timeout value itself is correct as a conservative margin.
Signed-off-by Md Shofiqul Islam <[email protected]>
I'm confused - why didn't you make the change Mike requested on v1?
Fine to argue against it but you need to reply to his review. Perhaps it went missing.
J
Quoted 17 lines
--- drivers/iio/adc/ti-ads1298.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/iio/adc/ti-ads1298.c +1
-1@@ -210,7 +210,7 @@ static int ads1298_read_one(struct ads1298_private *priv, int chan_index)return ret; } -/* Cannot take longer than 40ms (250Hz) */ +/* Cannot take longer than 4ms at the lowest rate (250Hz) */ ret =wait_for_completion_timeout (&priv->completion,msecs_to_jiffies (50 ));if (!ret)return -ETIMEDOUT ;
PATCH v2 3/3 iio: adc: ti-ads1298: Remove unnecessary CONFIG2 write during init
In reply to Md Shofiqul IslamThe driver was enabling the internal test signal (INT_TEST), double amplitude (TEST_AMP), and fast frequency (TEST_FREQ_FAST) bits in CONFIG2 during initialization. These bits activate an internal square wave generator intended for device testing and calibration, not normal ECG operation.
CONFIG2 defaults to having only the RESERVED bit set after reset, which is the correct value for normal operation. Remove the write entirely since it would just be writing the reset default value.
--- drivers/iio/adc/ti-ads1298.c | 9 --------- 1 file changed, 9 deletions(-)
drivers/iio/adc/ti-ads1298.c +0 -9
@@ -615,15 +615,6 @@ static int ads1298_init(struct iio_dev *indio_dev)if (!indio_dev->name)return -ENOMEM ; -/* Enable internal test signal, double amplitude, double frequency */ - ret =regmap_write (priv->regmap,ADS1298_REG_CONFIG2 , -ADS1298_MASK_CONFIG2_RESERVED | -ADS1298_MASK_CONFIG2_INT_TEST | -ADS1298_MASK_CONFIG2_TEST_AMP | -ADS1298_MASK_CONFIG2_TEST_FREQ_FAST ); -if (ret) -return ret; - val =ADS1298_MASK_CONFIG3_RESERVED ;/* Must write 1 always */ if (!priv->reg_vref) {/* Enable internal reference */
Signature · 1 line
2.54.0.windows.1
Jonathan Cameron
maintainerRe: [PATCH v2 3/3] iio: adc: ti-ads1298: Remove unnecessary CONFIG2 write during init
Quoted 6 lines · On Thu, 7 May 2026 13:51:28 +0300 Md Shofiqul Islam <[email protected]>…
The driver was enabling the internal test signal (
INT_TEST), double amplitude (TEST_AMP), and fast frequency (TEST_FREQ_FAST) bits in CONFIG2 during initialization. These bits activate an internal square wave generator intended for device testing and calibration, not normal ECG operation.
Quoted 6 lines
CONFIG2 defaults to having only the RESERVED bit set after reset, which is the correct value for normal operation. Remove the write entirely since it would just be writing the reset default value.
Suggested-by Mike Looijmans <[email protected]>Signed-off-by Md Shofiqul Islam <[email protected]>
Looks fine to me.
I'll pick it up once you've addressed comments on patch 2 that are outstanding.
Quoted 24 lines
--- drivers/iio/adc/ti-ads1298.c | 9 --------- 1 file changed, 9 deletions(-)drivers/iio/adc/ti-ads1298.c +0
-9@@ -615,15 +615,6 @@ static int ads1298_init(struct iio_dev *indio_dev)if (!indio_dev->name)return -ENOMEM ; -/* Enable internal test signal, double amplitude, double frequency */ - ret =regmap_write (priv->regmap,ADS1298_REG_CONFIG2 , -ADS1298_MASK_CONFIG2_RESERVED | -ADS1298_MASK_CONFIG2_INT_TEST | -ADS1298_MASK_CONFIG2_TEST_AMP | -ADS1298_MASK_CONFIG2_TEST_FREQ_FAST ); -if (ret) -return ret; - val =ADS1298_MASK_CONFIG3_RESERVED ;/* Must write 1 always */ if (!priv->reg_vref) {/* Enable internal reference */