scsi: mpt3sas: add hwmon support
Subsystems (3)
v2 cover scsi: mpt3sas: add hwmon support
Expose the IOC and board temperature sensors of LSI / Broadcom / Avago SAS HBAs that bind to mpt3sas through the hwmon interface. The data lives in MPI IO Unit Page 7.
The same fields are exposed by Broadcom's userspace tooling through the /dev/mpt[23]ctl ioctl path (typically root-only): IOCTemperature and BoardTemperature in lsiutil; ROC and Controller in storcli. With this driver, sensors(1) shows them unprivileged:
$ sensors mpt3sas-pci-0200 mpt3sas-pci-0200 Adapter: PCI adapter IOC: +42.0°C
v1 -> v2:
v1: https://lore.kernel.org/r/[email protected]
* Dropped misleading Documentation/hwmon/mpt3sas.rst.
* Dropped inaccurate concurrency-wait figure from Testing; corrected empirical data is in the on-list discussion.
Testing
-------
Validated across three Broadcom SAS chip generations. None of the cards had a board sensor present, so the testing only covers the IOC channel:
* LSI 9500-8i / SAS3816, SAS-3:
- hwmon device registers as "mpt3sas" with only temp1 (IOC) exposed
- IOC reading matches storcli /c0 show temperature and lsiutil -p1 -a 25,2,0,0
- rmmod / modprobe cycle goes through the explicit unregister/register paths cleanly
* LSI 9305-24i / SAS3224, SAS-3: same behaviour.
* LSI 9211-4i / SAS2004, SAS-2: firmware reports both *TemperatureUnits = NOT_PRESENT, no hwmon device registered (graceful-skip path).
Not verified (no available hardware):
* Path with both IOC and board sensors present.
* Fahrenheit-units conversion.
* Sub-zero readings (signed-cast path).
Louis Sautier (2):
scsi: mpt3sas: add IO Unit Page 7 config accessor
scsi: mpt3sas: add hwmon support
drivers/scsi/mpt3sas/Kconfig | 9 ++ drivers/scsi/mpt3sas/Makefile | 2 + drivers/scsi/mpt3sas/mpt3sas_base.h | 19 +++ drivers/scsi/mpt3sas/mpt3sas_config.c | 36 +++++ drivers/scsi/mpt3sas/mpt3sas_hwmon.c | 200 ++++++++++++++++++++++++++ drivers/scsi/mpt3sas/mpt3sas_scsih.c | 6 + 6 files changed, 272 insertions(+) create mode 100644 drivers/scsi/mpt3sas/mpt3sas_hwmon.c
base-commit: 5d6919055dec134de3c40167a490f33c74c12581
Signature · 1 line
2.54.0
PATCH v2 1/2 scsi: mpt3sas: add IO Unit Page 7 config accessor
Add mpt3sas_config_get_iounit_pg7(), mirroring the existing iounit page accessors. Used by the hwmon driver added in the following patch to read the IOC and board temperatures.
--- drivers/scsi/mpt3sas/mpt3sas_base.h | 2 ++ drivers/scsi/mpt3sas/mpt3sas_config.c | 36 +++++++++++++++++++++++++++ 2 files changed, 38 insertions(+)
drivers/scsi/mpt3sas/mpt3sas_base.h +2 -0
@@ -1904,6 +1904,8 @@ int mpt3sas_config_get_iounit_pg3(struct MPT3SAS_ADAPTER *ioc, Mpi2ConfigReply_t *mpi_reply, Mpi2IOUnitPage3_t *config_page, u16 sz);int mpt3sas_config_set_iounit_pg1 (struct MPT3SAS_ADAPTER *ioc,Mpi2ConfigReply_t *mpi_reply,Mpi2IOUnitPage1_t *config_page); +int mpt3sas_config_get_iounit_pg7 (struct MPT3SAS_ADAPTER *ioc, +Mpi2ConfigReply_t *mpi_reply,Mpi2IOUnitPage7_t *config_page);int mpt3sas_config_get_iounit_pg8 (struct MPT3SAS_ADAPTER *ioc,Mpi2ConfigReply_t *mpi_reply,Mpi2IOUnitPage8_t *config_page); int mpt3sas_config_get_sas_iounit_pg1(struct MPT3SAS_ADAPTER *ioc,
drivers/scsi/mpt3sas/mpt3sas_config.c +36 -0
@@ -991,6 +991,42 @@ mpt3sas_config_get_iounit_pg3(struct MPT3SAS_ADAPTER *ioc,return r; } +/** +* mpt3sas_config_get_iounit_pg7 - obtain iounit page 7 +* @ioc: per adapter object +* @mpi_reply: reply mf payload returned from firmware +* @config_page: contents of the config page +* Context: sleep. +* +* Return: 0 for success, non-zero for failure. +*/ +int +mpt3sas_config_get_iounit_pg7 (struct MPT3SAS_ADAPTER *ioc, +Mpi2ConfigReply_t *mpi_reply,Mpi2IOUnitPage7_t *config_page) +{ +Mpi2ConfigRequest_t mpi_request; +int r; + +memset (&mpi_request,0 ,sizeof (Mpi2ConfigRequest_t)); + mpi_request.Function =MPI2_FUNCTION_CONFIG ; + mpi_request.Action =MPI2_CONFIG_ACTION_PAGE_HEADER ; + mpi_request.Header.PageType =MPI2_CONFIG_PAGETYPE_IO_UNIT ; + mpi_request.Header.PageNumber =7 ; + mpi_request.Header.PageVersion =MPI2_IOUNITPAGE7_PAGEVERSION ; + ioc->build_zero_len_sge_mpi (ioc, &mpi_request.PageBufferSGE); + r =_config_request (ioc, &mpi_request, mpi_reply, +MPT3_CONFIG_PAGE_DEFAULT_TIMEOUT ,NULL ,0 ); +if (r) + goto out; + + mpi_request.Action =MPI2_CONFIG_ACTION_PAGE_READ_CURRENT ; + r =_config_request (ioc, &mpi_request, mpi_reply, +MPT3_CONFIG_PAGE_DEFAULT_TIMEOUT , config_page, +sizeof (*config_page)); + out: +return r; +} +/** * mpt3sas_config_get_iounit_pg8 - obtain iounit page 8 * @ioc: per adapter object
Signature · 1 line
2.54.0
PATCH v2 2/2 scsi: mpt3sas: add hwmon support
In reply to Louis SautierExpose the IOC and board temperature sensors of LSI / Broadcom SAS HBAs through hwmon. Readings come from MPI IO Unit Page 7 via the accessor added in the preceding patch.
The same fields are exposed by Broadcom's userspace tooling through the /dev/mpt[23]ctl ioctl path (typically root-only):
IOCTemperature and BoardTemperature in lsiutil; ROC and Controller in storcli. With this driver, sensors(1) shows them unprivileged:
$ sensors mpt3sas-pci-0200 mpt3sas-pci-0200 Adapter: PCI adapter IOC: +42.0°C
Each channel is gated independently by its *TemperatureUnits field through is_visible(); cards that populate only one sensor expose only one input file, and cards that populate neither do not register an hwmon device.
Built into mpt3sas.ko under a new CONFIG_SCSI_MPT3SAS_HWMON Kconfig option.
--- drivers/scsi/mpt3sas/Kconfig | 9 ++ drivers/scsi/mpt3sas/Makefile | 2 + drivers/scsi/mpt3sas/mpt3sas_base.h | 17 +++ drivers/scsi/mpt3sas/mpt3sas_hwmon.c | 200 +++++++++++++++++++++++++++ drivers/scsi/mpt3sas/mpt3sas_scsih.c | 6 + 5 files changed, 234 insertions(+) create mode 100644 drivers/scsi/mpt3sas/mpt3sas_hwmon.c
drivers/scsi/mpt3sas/Kconfig +9 -0
@@ -73,6 +73,15 @@ config SCSI_MPT3SAS_MAX_SGE can be 256. However, it may decreased down to 16. Decreasing this parameter will reduce memory requirements on a per controller instance. +config SCSI_MPT3SAS_HWMON + bool "LSI MPT Fusion SAS hwmon support" + depends on SCSI_MPT3SAS && HWMON + depends on !(SCSI_MPT3SAS=y && HWMON=m) + help + Say Y here to expose the IOC and board temperature sensors of + LSI / Broadcom SAS HBAs (such as the 9300, 9400, and 9500 series) + through hwmon. See Documentation/hwmon/mpt3sas.rst for details. + config SCSI_MPT2SAS tristate "Legacy MPT2SAS config option" default n
drivers/scsi/mpt3sas/Makefile +2 -0
@@ -9,3 +9,5 @@ mpt3sas-y += mpt3sas_base.o \ mpt3sas_trigger_diag.o \ mpt3sas_warpdrive.o \ mpt3sas_debugfs.o \ + +mpt3sas-$(CONFIG_SCSI_MPT3SAS_HWMON) += mpt3sas_hwmon.o
drivers/scsi/mpt3sas/mpt3sas_base.h +17 -0
@@ -1629,6 +1629,7 @@ struct MPT3SAS_ADAPTER {u8 is_aero_ioc;struct dentry *debugfs_root;struct dentry *ioc_dump; +struct mpt3sas_hwmon *hwmon;PUT_SMID_IO_FP_HIP put_smid_scsi_io;PUT_SMID_IO_FP_HIP put_smid_fast_path;PUT_SMID_IO_FP_HIP put_smid_hi_priority;
@@ -2049,6 +2050,22 @@ void mpt3sas_destroy_debugfs(struct MPT3SAS_ADAPTER *ioc);void mpt3sas_init_debugfs (void );void mpt3sas_exit_debugfs (void ); +#if IS_ENABLED (CONFIG_SCSI_MPT3SAS_HWMON ) +int mpt3sas_hwmon_register (struct MPT3SAS_ADAPTER *ioc); +void mpt3sas_hwmon_unregister (struct MPT3SAS_ADAPTER *ioc); +#else +static inline int +mpt3sas_hwmon_register (struct MPT3SAS_ADAPTER *ioc) +{ +return 0 ; +} + +static inline void +mpt3sas_hwmon_unregister (struct MPT3SAS_ADAPTER *ioc) +{ +} +#endif +/** * _scsih_is_pcie_scsi_device - determines if device is an pcie scsi device * @device_info: bitfield providing information about the device.
drivers/scsi/mpt3sas/mpt3sas_hwmon.c new file +200 -0
200 lines not on this page · raw message
drivers/scsi/mpt3sas/mpt3sas_scsih.c +6 -0
@@ -12562,6 +12562,7 @@ static void scsih_remove(struct pci_dev *pdev)/* release all the volumes */ _scsih_ir_shutdown (ioc);mpt3sas_destroy_debugfs (ioc); +mpt3sas_hwmon_unregister (ioc);sas_remove_host (shost);list_for_each_entry_safe (raid_device, next, &ioc->raid_device_list, list) {
@@ -13651,6 +13652,11 @@ _scsih_probe(struct pci_dev *pdev, const struct pci_device_id *id) }scsi_scan_host (shost); + +if (mpt3sas_hwmon_register (ioc)) +ioc_warn (ioc, +"hwmon registration failed; temperatures not exposed\n" ); +mpt3sas_setup_debugfs (ioc);return 0 ; out_add_shost_fail:
Signature · 1 line
2.54.0
[email protected]
AI reviewThank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider: - [Low] The Kconfig help text references a non-existent documentation file. --
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Low] The Kconfig help text references a non-existent documentation file. --
commit 8d7ed075db4ca1d1d6c8f7e90a2625cc47892773
Author: Louis Sautier <[email protected]>
scsi: mpt3sas: add hwmon support
This commit exposes the IOC and board temperature sensors of LSI / Broadcom SAS HBAs through the hardware monitoring subsystem, using readings from MPI IO Unit Page 7.
Quoted 6 lines
drivers/scsi/mpt3sas/Kconfig +0
-0@@ -73,6 +73,15 @@ config SCSI_MPT3SAS_MAX_SGE can be 256. However, it may decreased down to 16. Decreasing this
drivers/scsi/mpt3sas/Kconfig config SCSI_MPT3SAS_MAX_SGE · line 83
Quoted 10 lines
drivers/scsi/mpt3sas/Kconfig +8
-0parameter will reduce memory requirements on a per controller instance. +config SCSI_MPT3SAS_HWMON + bool "LSI MPT Fusion SAS hwmon support" + depends on SCSI_MPT3SAS && HWMON + depends on !(SCSI_MPT3SAS=y && HWMON=m) + help + Say Y here to expose the IOC and board temperature sensors of + LSI / Broadcom SAS HBAs (such as the 9300, 9400, and 9500 series) + through hwmon. See Documentation/hwmon/mpt3sas.rst for details.
This isn't a bug, but the help text references a documentation file that doesn't seem to be included in this patch. Is Documentation/hwmon/mpt3sas.rst missing from this commit, or was this added in a separate patch series?
Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=2
Quoted 4 lines · On Mon, 18 May 2026 19:37:57 +0000, [email protected] wrote:
Quoted 4 lines
drivers/scsi/mpt3sas/Kconfig +4
-0+config SCSI_MPT3SAS_HWMON + bool "LSI MPT Fusion SAS hwmon support" + depends on SCSI_MPT3SAS && HWMON + depends on !(SCSI_MPT3SAS=y && HWMON=m)
Quoted 8 lines
drivers/scsi/mpt3sas/Kconfig config SCSI_MPT3SAS_MAX_SGE · line 83
Quoted 4 lines
drivers/scsi/mpt3sas/Kconfig +4
-0+ help + Say Y here to expose the IOC and board temperature sensors of + LSI / Broadcom SAS HBAs (such as the 9300, 9400, and 9500 series) + through hwmon. See Documentation/hwmon/mpt3sas.rst for details.This isn't a bug, but the help text references a documentation file that doesn't seem to be included in this patch. Is
Documentation/hwmon/mpt3sas.rstmissing from this commit, or was this added in a separate patch series?
I forgot to remove this sentence after dropping the documentation. I will do it in v3.