devlink: add generic device max_sfs parameter
Subsystems (6)
Tariq Toukan
maintainerv3 cover devlink: add generic device max_sfs parameter
Hi,
This series by Nikolay introduces a new generic devlink device parameter, max_sfs, to control the number of light-weight NIC subfunctions (SFs) that can be created on a device.
The first patch adds the generic devlink parameter and infrastructure support.
The second patch implements support for the parameter in the mlx5 driver.
With this addition, users can enable or disable SF creation directly via devlink, without relying on external vendor-specific tools.
Regards,
Tariq
Notes about a few items from a previous Sashiko review:
Quoted 4 lines
Should there be a validate callback analogous to
mlx5_devlink_total_vfs_validate()that reads the cap and rejects values above the device-reported maximum, so the documented "device-specific max" is actually enforced?
N: I don't know of such cap, if there was I'd have added it.
Quoted 7 lines
mlx5_devlink_total_vfs_set()rejects with-EOPNOTSUPPand an extack "SRIOV is not per PF on this device" whensriov_supportorper_pf_total_vf_supportedis clear, but no equivalentper_pf_num_sf_supported(or any SF-related) capability bit is added tonv_global_pci_cap_bitsor queried here. On hardware that lacks the feature, the user only sees the generic firmware error "Failed to change ... global PCI configuration".
N: I don't know of such bit, if there was such bit I'd have added it.
Quoted 10 lines
At this point, a successful write of
per_pf_num_sfhas already been committed to non-volatile firmware storage. If the subsequentmlx5_nv_param_read_per_host_pf_conf()or the secondmlx5_nv_param_write()fails (for example, transientfirmware/PCIeissue), is there a path that rolls backper_pf_num_sf?Because these are permanent parameters that "require a reboot to take effect", a half-applied state (e.g., per_pf_num_sf=1 but pf_total_sf_en=0/total_sf=0) appears to persist across reboots until the user issues another successful set.
N: That is expected and in line with the rest of the code.
Quoted 5 lines
The commit message says
max_sfsis to "control the total light-weight NIC subfunctions"; the BAR-size side-effect is not mentioned, and any previously configuredlog_sf_bar_sizeis overwritten on everymax_sfsset. Should that behavior be documented or split out from the count knob?
N: It should be documented when it is split out, at present time - no.
V3, all changes are in patch 02 (mlx5 implementation):
- Cap max_sfs at U16_MAX using a validate callback (sashiko)
- Change the warning message to match the docs (sashiko)
- On get verify that per_pf_num_sf & pf_total_sf_en are set otherwise return 0 since it means SFs are not properly enabled (sashiko)
- Define the default log bar size and use it instead of raw value (sashiko)
V2:
https://lore.kernel.org/netdev/[email protected]/
Nikolay Aleksandrov (2):
devlink: add generic device max_sfs parameter
net/mlx5: implement max_sfs parameter
.../networking/devlink/devlink-params.rst | 6 + Documentation/networking/devlink/mlx5.rst | 7 +- .../mellanox/mlx5/core/lib/nv_param.c | 118 +++++++++++++++++- include/net/devlink.h | 4 + net/devlink/param.c | 5 + 5 files changed, 136 insertions(+), 4 deletions(-)
base-commit: c2c0486c56800ce276e79c40a6e576ffd672f2a9
Signature · 1 line
2.44.0
Tariq Toukan
maintainerPATCH v3 1/2 devlink: add generic device max_sfs parameter
From: Nikolay Aleksandrov <[email protected]>
Add a new generic devlink device parameter (max_sfs) to control if and how many light-weight NIC subfunctions can be created. Subfunctions are a light-weight network functions backed by an underlying PCI function. Their lifecycle can already be managed by devlink, but currently users cannot enable them in the device. They can be enabled/disabled only via external vendor tools. This parameter allows subfunctions to be enabled (>0) or disabled (0) via devlink. A subsequent patch will add support for max_sfs to the mlx5 driver.
--- Documentation/networking/devlink/devlink-params.rst | 6 ++++++ include/net/devlink.h | 4 ++++ net/devlink/param.c | 5 +++++ 3 files changed, 15 insertions(+)
Documentation/networking/devlink/devlink-params.rst +6 -0
@@ -165,3 +165,9 @@ own name. - u32 - Controls the maximum number of MAC address filters that can be assigned to a Virtual Function (VF). + * - ``max_sfs`` + - u32 + - The maximum number of subfunctions which can be created on the device. + Modifying this parameter may require a device restart and PCI bus + rescanning because the BAR layout may change. A value of 0 disables + subfunction creation.
include/net/devlink.h +4 -0
@@ -546,6 +546,7 @@ enum devlink_param_generic_id {DEVLINK_PARAM_GENERIC_ID_TOTAL_VFS ,DEVLINK_PARAM_GENERIC_ID_NUM_DOORBELLS ,DEVLINK_PARAM_GENERIC_ID_MAX_MAC_PER_VF , +DEVLINK_PARAM_GENERIC_ID_MAX_SFS ,/* add new param generic ids above here*/ __DEVLINK_PARAM_GENERIC_ID_MAX,
@@ -619,6 +620,9 @@ enum devlink_param_generic_id {#define DEVLINK_PARAM_GENERIC_MAX_MAC_PER_VF_NAME "max_mac_per_vf"#define DEVLINK_PARAM_GENERIC_MAX_MAC_PER_VF_TYPE DEVLINK_PARAM_TYPE_U32 +#define DEVLINK_PARAM_GENERIC_MAX_SFS_NAME "max_sfs" +#define DEVLINK_PARAM_GENERIC_MAX_SFS_TYPE DEVLINK_PARAM_TYPE_U32 +#define DEVLINK_PARAM_GENERIC (_id, _cmodes, _get, _set, _validate) \ { \ .id = DEVLINK_PARAM_GENERIC_ID_##_id, \
net/devlink/param.c +5 -0
@@ -117,6 +117,11 @@ static const struct devlink_param devlink_param_generic[] = { .name = DEVLINK_PARAM_GENERIC_MAX_MAC_PER_VF_NAME, .type = DEVLINK_PARAM_GENERIC_MAX_MAC_PER_VF_TYPE, }, + { + .id = DEVLINK_PARAM_GENERIC_ID_MAX_SFS, + .name = DEVLINK_PARAM_GENERIC_MAX_SFS_NAME, + .type = DEVLINK_PARAM_GENERIC_MAX_SFS_TYPE, + }, };static int devlink_param_generic_verify (const struct devlink_param *param)
Signature · 1 line
2.44.0
Tariq Toukan
maintainerPATCH v3 2/2 net/mlx5: implement max_sfs parameter
In reply to Tariq ToukanFrom: Nikolay Aleksandrov <[email protected]>
Implement max_sfs generic parameter to allow users to control the total light-weight NIC subfunctions that can be created using devlink instead of external vendor tools. A value of 0 will effectively disable creation of new subfunction devices. A warning is sent to user-space via extack (returning extack without error code is interpreted as a warning by user-space tools). The maximum value is capped at U16_MAX.
--- Documentation/networking/devlink/mlx5.rst | 7 +- .../mellanox/mlx5/core/lib/nv_param.c | 118 +++++++++++++++++- 2 files changed, 121 insertions(+), 4 deletions(-)
Documentation/networking/devlink/mlx5.rst +6 -1
@@ -45,8 +45,13 @@ Parameters - The range is between 1 and a device-specific max. - Applies to each physical function (PF) independently, if the device supports it. Otherwise, it applies symmetrically to all PFs. + * - ``max_sfs`` + - permanent + - The range is between 0 and a device-specific max. + - Applies to each physical function (PF) independently. -Note: permanent parameters such as ``enable_sriov`` and ``total_vfs`` require FW reset to take effect +Note: permanent parameters such as ``enable_sriov``, ``total_vfs`` and ``max_sfs`` + require FW reset to take effect .. code-block:: bash
drivers/net/ethernet/mellanox/mlx5/core/lib/nv_param.c +115 -3
149 lines not on this page · raw message
Signature · 1 line
2.44.0
From: Tariq Toukan <[email protected]>
Date: Wed, 3 Jun 2026 13:26:44 +0300
Quoted 6 lines
Hi,
This series by Nikolay introduces a new generic devlink device parameter,
max_sfs, to control the number of light-weight NIC subfunctions (SFs) that can be created on a device.
Quoted 7 lines
The first patch adds the generic devlink parameter and infrastructure support.
The second patch implements support for the parameter in the mlx5 driver.With this addition, users can enable or disable SF creation directly via devlink, without relying on external vendor-specific tools.
For the series:
Quoted 3 lines
Regards,
Tariq
Thanks,
Olek
Quoted 11 lines · Tariq Toukan
Hi,
This series by Nikolay introduces a new generic devlink device parameter,
max_sfs, to control the number of light-weight NIC subfunctions (SFs) that can be created on a device.The first patch adds the generic devlink parameter and infrastructure support.
The second patch implements support for the parameter in the mlx5 driver.
Quoted 7 lines
With this addition, users can enable or disable SF creation directly via devlink, without relying on external vendor-specific tools.
Regards,
Tariq
Need to rebase due to commit d603517771d8 ("devlink: pass param values by pointer"). Sorry for the noise.