Skip to contentSkip to conversation

riscv: dts: spacemit: k3: Enable SD card support

PATCH Applied Yixun Lan 1 participant 2 messages Jun 10 – Jul 14

Subsystems (3)
lore
Share & tools
lore

Yixun Lan

author maintainer
#0 lore raw

PATCH 1/1 riscv: dts: spacemit: k3: Enable SD card support

Add the device tree node of SDHCI-0 controller which found on CoM260-IFX board, it's currenty used for Micro SD card slot, and one GPIO pin is configured as card insertion/removal detection pin, the slot use 4-bit data bus, and up support to SDR104 speed mode.

---
 arch/riscv/boot/dts/spacemit/k3-com260-ifx.dts | 18 +++++++++++
 arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi   | 44 ++++++++++++++++++++++++++
 arch/riscv/boot/dts/spacemit/k3.dtsi           | 13 ++++++++
 3 files changed, 75 insertions(+)
arch/riscv/boot/dts/spacemit/k3-com260-ifx.dts +18 -0
index 238bb03d0e9e..e7f76cd24b90 100644
@@ -19,3 +19,21 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 };
+
+&sdhci0 {
+	pinctrl-names = "default","uhs";
+	pinctrl-0 = <&mmc1_cfg>;
+	pinctrl-1 = <&mmc1_uhs_cfg>;
+	bus-width = <4>;
+	cd-gpios = <&gpio K3_GPIO(4) GPIO_ACTIVE_HIGH>;
+	no-mmc;
+	no-sdio;
+	disable-wp;
+	cap-sd-highspeed;
+	vmmc-supply = <&aldo4>;
+	vqmmc-supply = <&aldo1>;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi +44 -0

48 lines not on this page · raw message

arch/riscv/boot/dts/spacemit/k3.dtsi +13 -0
index 19fc9b49668e..dabb0d5e6bad 100644
@@ -1099,6 +1099,19 @@ pll: clock-controller@d4090000 {
 			#clock-cells = <1>;
 		};
 
+		sdhci0: mmc@d4280000 {
+			compatible = "spacemit,k3-sdhci";
+			reg = <0x0 0xd4280000 0x0 0x200>;
+			clocks = <&syscon_apmu CLK_APMU_SDH_AXI>,
+				 <&syscon_apmu CLK_APMU_SDH0>;
+			clock-names = "core", "io";
+			resets = <&syscon_apmu RESET_APMU_SDH_AXI>,
+				 <&syscon_apmu RESET_APMU_SDH0>;
+			reset-names = "axi", "sdh";
+			interrupts = <99 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
 		syscon_apmu: system-controller@d4282800 {
 			compatible = "spacemit,k3-syscon-apmu";
 			reg = <0x0 0xd4282800 0x0 0x400>;

---
base-commit: 38d5f73d1f5af60d87047b981736b89521e49213
change-id: 20260609-07-k3-enable-sd-e1ddf090e87f

Best regards,

Signature · 1 line
Yixun Lan <[email protected]>
author maintainer Applied
#1 lore raw
Quoted 4 lines · Yixun Lan

Add the device tree node of SDHCI-0 controller which found on CoM260-IFX board, it's currenty used for Micro SD card slot, and one GPIO pin is configured as card insertion/removal detection pin, the slot use 4-bit data bus, and up support to SDR104 speed mode.

Applied, thanks!

[1/1] riscv: dts: spacemit: k3: Enable SD card support

      https://git.kernel.org/pub/scm/linux/kernel/git/spacemit/linux.git/commit/?id=055044260e7a603ff587537651e12c8fbfbed851

Best regards,

Signature · 1 line
Yixun Lan <[email protected]>