Skip to contentSkip to conversation

staging: rtl8723bs: replace beacon timing magic numbers

PATCH In review Jad Keskes 3 participants 3 messages Jun 16 – Jul 7 Staging

lore
Share & tools
lore

Jad Keskes

author
#0 lore raw

PATCH 1/1 staging: rtl8723bs: replace beacon timing magic numbers

Break down the 0x6404 and 0x660F in rtl8723b_InitBeaconParameters() so people don't need the out-of-tree driver open to know what these do.

REG_TBTT_PROHIBIT (0x0540): 0x6404 = hold (0x64) and setup (0x04), both in 32us ticks. Same layout as rtw88.

REG_BCNTCFG (0x0510): 0x660F is an EDCA-like register. Lower byte is AIFS (0x0F = no contention before beacon), next nibble is CWmin (0x06), top nibble is CWmax (0x06). Matches rtl8192cu which writes 0x66FF (test chips) and 0x660F (production).

Drop the TODO since this was the last thing it referenced.

---
 drivers/staging/rtl8723bs/hal/rtl8723b_hal_init.c |  5 ++---
 drivers/staging/rtl8723bs/include/rtl8723b_hal.h  | 13 +++++++++++++
 2 files changed, 15 insertions(+), 3 deletions(-)
drivers/staging/rtl8723bs/hal/rtl8723b_hal_init.c +2 -3
index bcaf63b2893c..2cf1cd9d19de 100644
@@ -861,8 +861,7 @@ void rtl8723b_InitBeaconParameters(struct adapter *padapter)
 
 	rtw_write16(padapter, REG_BCN_CTRL, val16);
 
-	/*  TODO: Remove these magic number */
-	rtw_write16(padapter, REG_TBTT_PROHIBIT, 0x6404);/*  ms */
+	rtw_write16(padapter, REG_TBTT_PROHIBIT, TBTT_PROHIBIT_TIME_8723B);
 	/*  Firmware will control REG_DRVERLYINT when power saving is enable, */
 	/*  so don't set this register on STA mode. */
 	if (!check_fwstate(&padapter->mlmepriv, WIFI_STATION_STATE))
@@ -871,7 +870,7 @@ void rtl8723b_InitBeaconParameters(struct adapter *padapter)
 
 	/*  Suggested by designer timchen. Change beacon AIFS to the largest number */
 	/*  because test chip does not contension before sending beacon. by tynli. 2009.11.03 */
-	rtw_write16(padapter, REG_BCNTCFG, 0x660F);
+	rtw_write16(padapter, REG_BCNTCFG, BCNTCFG_8723B);
 
 	pHalData->RegBcnCtrlVal = rtw_read8(padapter, REG_BCN_CTRL);
 	pHalData->RegTxPause = rtw_read8(padapter, REG_TXPAUSE);
drivers/staging/rtl8723bs/include/rtl8723b_hal.h +13 -0
index b6006110ad6b..aa7676828371 100644
@@ -72,6 +72,19 @@ struct rt_firmware_hdr {
 #define DRIVER_EARLY_INT_TIME_8723B  0x05
 #define BCN_DMA_ATIME_INT_TIME_8723B 0x02
 
+/* REG_TBTT_PROHIBIT (0x0540) - TBTT prohibit hold/setup in 32us units */
+#define TBTT_PROHIBIT_SETUP_8723B 0x04
+#define TBTT_PROHIBIT_HOLD_8723B  0x64
+#define TBTT_PROHIBIT_TIME_8723B \
+	((TBTT_PROHIBIT_HOLD_8723B << 8) | TBTT_PROHIBIT_SETUP_8723B)
+
+/* REG_BCNTCFG (0x0510) - beacon AIFS, CWmin, CWmax (EDCA-like layout) */
+#define BCN_AIFS_8723B   0x0F
+#define BCN_CW_MIN_8723B 0x06
+#define BCN_CW_MAX_8723B 0x06
+#define BCNTCFG_8723B \
+	((BCN_CW_MAX_8723B << 12) | (BCN_CW_MIN_8723B << 8) | BCN_AIFS_8723B)
+
 /* for 8723B */
 /* TX 32K, RX 16K, Page size 128B for TX, 8B for RX */
 #define PAGE_SIZE_TX_8723B 128
Signature · 1 line
2.54.0
Reviewed-by on v1 1/1
#1 lore raw
Quoted 12 lines · Jad Keskes

Break down the 0x6404 and 0x660F in rtl8723b_InitBeaconParameters() so people don't need the out-of-tree driver open to know what these do.

REG_TBTT_PROHIBIT (0x0540): 0x6404 = hold (0x64) and setup (0x04), both in 32us ticks. Same layout as rtw88.

REG_BCNTCFG (0x0510): 0x660F is an EDCA-like register. Lower byte is AIFS (0x0F = no contention before beacon), next nibble is CWmin (0x06), top nibble is CWmax (0x06). Matches rtl8192cu which writes 0x66FF (test chips) and 0x660F (production).

Quoted 6 lines

Drop the TODO since this was the last thing it referenced.

---

Seems reasonable.

regards,
dan carpenter

#2 lore raw
In reply to Jad Keskes
Quoted 12 lines · Jad Keskes

Break down the 0x6404 and 0x660F in rtl8723b_InitBeaconParameters() so people don't need the out-of-tree driver open to know what these do.

REG_TBTT_PROHIBIT (0x0540): 0x6404 = hold (0x64) and setup (0x04), both in 32us ticks. Same layout as rtw88.

REG_BCNTCFG (0x0510): 0x660F is an EDCA-like register. Lower byte is AIFS (0x0F = no contention before beacon), next nibble is CWmin (0x06), top nibble is CWmax (0x06). Matches rtl8192cu which writes 0x66FF (test chips) and 0x660F (production).

Quoted 5 lines

Drop the TODO since this was the last thing it referenced.

This is v2, right? Please always document this properly.

thanks,

greg k-h