Skip to contentSkip to conversation

dt-bindings: w1: Convert HDQ One Wire to DT schema

PATCH Applied Eduard Bostina 2 participants 3 messages Jun 30 – Jul 3

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 dt-bindings: w1: Convert HDQ One Wire to DT schema

Convert the Texas Instruments OMAP HDQ One Wire bindings to DT schema.

During the conversion, several updates were made to reflect actual hardware usage and resolve dtbs_check warnings:
- 'ti,hwmods' has been made optional.
- Added 'clocks' and 'clock-names' properties as they are used in actual device trees (e.g., am437x-l4.dtsi).
- Added a second example for the AM4372 HDQ controller to demonstrate the clock and interrupt configuration.

---
 .../devicetree/bindings/w1/omap-hdq.txt       | 22 ------
 .../devicetree/bindings/w1/ti,hdq.yaml        | 70 +++++++++++++++++++
 2 files changed, 70 insertions(+), 22 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/w1/omap-hdq.txt
 create mode 100644 Documentation/devicetree/bindings/w1/ti,hdq.yaml
Documentation/devicetree/bindings/w1/omap-hdq.txt deleted +0 -22
deleted file mode 100644
index 913c5f91a0f9..000000000000
@@ -1,22 +0,0 @@
-* OMAP HDQ One wire bus master controller
-
-Required properties:
-- compatible : should be "ti,omap3-1w" or "ti,am4372-hdq"
-- reg : Address and length of the register set for the device
-- interrupts : interrupt line.
-- ti,hwmods : "hdq1w"
-
-Optional properties:
-- ti,mode: should be "hdq": HDQ mode  "1w": one-wire mode.
-	   If not specified HDQ mode is implied.
-
-Example:
-
-- From omap3.dtsi
-  hdqw1w: 1w@480b2000 {
-	compatible = "ti,omap3-1w";
-	reg = <0x480b2000 0x1000>;
-	interrupts = <58>;
-	ti,hwmods = "hdq1w";
-	ti,mode = "hdq";
-  };
Documentation/devicetree/bindings/w1/ti,hdq.yaml new file +70 -0

70 lines not on this page · raw message

Signature · 1 line
2.43.0
maintainer Reviewed-by on v1 1/1
#1 lore raw
Quoted 11 lines · Eduard Bostina

Convert the Texas Instruments OMAP HDQ One Wire bindings to DT schema.

During the conversion, several updates were made to reflect actual hardware usage and resolve dtbs_check warnings:
- 'ti,hwmods' has been made optional.
- Added 'clocks' and 'clock-names' properties as they are used in actual device trees (e.g., am437x-l4.dtsi).
- Added a second example for the AM4372 HDQ controller to demonstrate the clock and interrupt configuration.

Wearing DT hat:

Best regards,
Krzysztof

maintainer Applied
#2 lore raw
In reply to Eduard Bostina
Quoted 11 lines · Eduard Bostina

Convert the Texas Instruments OMAP HDQ One Wire bindings to DT schema.

During the conversion, several updates were made to reflect actual hardware usage and resolve dtbs_check warnings:
- 'ti,hwmods' has been made optional.
- Added 'clocks' and 'clock-names' properties as they are used in actual device trees (e.g., am437x-l4.dtsi).
- Added a second example for the AM4372 HDQ controller to demonstrate the clock and interrupt configuration.

[...]

Applied, thanks!

[1/1] dt-bindings: w1: Convert HDQ One Wire to DT schema

      https://git.kernel.org/krzk/linux-w1/c/e89bccb295a8880493693e69e091a3668dc0c279

Best regards,

Signature · 1 line
Krzysztof Kozlowski <[email protected]>