ASoC: rt712: add mute led control for specific machines
Subsystems (3)
PATCH 1/1 ASoC: rt712: add mute led control for specific machines
From: Shuming Fan <[email protected]>
Certain HP platforms use the RT712 GPIOs to control the microphone mute LED and mute LED. This patch registers LED class devices in the codec driver to control the GPIOs through the LED subsystem.
--- sound/soc/codecs/rt712-sdca-sdw.h | 3 + sound/soc/codecs/rt712-sdca.c | 91 +++++++++++++++++++++++++++++++ sound/soc/codecs/rt712-sdca.h | 3 + 3 files changed, 97 insertions(+)
sound/soc/codecs/rt712-sdca-sdw.h +3 -0
@@ -45,6 +45,9 @@ static const struct reg_default rt712_sdca_mbq_defaults[] = { { 0x5b00029, 0x3fff }, { 0x5b0002a, 0xf000 }, { 0x6100000, 0x04e4 }, + { 0x6100009, 0x0000 }, + { 0x610000a, 0x0000 }, + { 0x610000b, 0x0020 }, { 0x610000e, 0x0007 }, { 0x6100045, 0x0860 }, { 0x6100046, 0x0029 },
sound/soc/codecs/rt712-sdca.c +91 -0
115 lines not on this page · raw message
sound/soc/codecs/rt712-sdca.h +3 -0
@@ -113,6 +113,9 @@ struct rt712_dmic_kctrl_priv {#define RT712_HDA_LEGACY_MUX_CTL0 0x00#define RT712_HDA_LEGACY_CONFIG_CTL0 0x06#define RT712_HDA_LEGACY_RESET_CTL 0x08 +#define RT712_HDA_GPIO_EN_CTL 0x09 +#define RT712_HDA_GPIO_DIRECTION_CTL 0x0a +#define RT712_HDA_GPIO_SET_CTL 0x0b#define RT712_HDA_LEGACY_GPIO_WAKE_EN_CTL 0x0e#define RT712_DMIC_ENT_FLOAT_CTL 0x10#define RT712_DMIC_GAIN_ENT_FLOAT_CTL0 0x11
Signature · 1 line
2.54.0
Mark Brown
maintainerQuoted 6 lines · On Wed, Jul 01, 2026 at 05:05:30PM +0800, [email protected] wrote:
Certain HP platforms use the RT712 GPIOs to control the microphone mute LED and mute LED. This patch registers LED class devices in the codec driver to control the GPIOs through the LED subsystem.
sound/soc/codecs/rt712-sdca.c +1
-0+#ifdef CONFIG_LEDS_TRIGGERS
sound/soc/codecs/rt712-sdca.c static int rt712_sdca_index_update_bits(struct rt712_sdca_priv *rt712, · line 115
Quoted 10 lines
sound/soc/codecs/rt712-sdca.c +9
-0+static int rt712_sdca_mute_led_set (struct led_classdev *led_cdev, +enum led_brightness brightness) +{ +rt712_sdca_index_update_bits (rt712,RT712_VENDOR_HDA_CTL , +RT712_HDA_GPIO_EN_CTL , (1 << gpio_pin), (1 << gpio_pin)); +rt712_sdca_index_update_bits (rt712,RT712_VENDOR_HDA_CTL , +RT712_HDA_GPIO_DIRECTION_CTL , (1 << gpio_pin), (1 << gpio_pin)); +rt712_sdca_index_update_bits (rt712,RT712_VENDOR_HDA_CTL , +RT712_HDA_GPIO_SET_CTL , (1 << gpio_pin), (value << gpio_pin));
This all looks like we should register a GPIO and let the LED subsystem GPIO support do the LED glue.
sound/soc/codecs/rt712-sdca.c static int rt712_sdca_index_update_bits(struct rt712_sdca_priv *rt712, · line 143
Quoted 3 lines
sound/soc/codecs/rt712-sdca.c +3
-0+for (i =0 ; i <NUM_AUDIO_LEDS ; i++) { + mute_led_cdev[i].trigger_data = (void *)rt712; + err =devm_led_classdev_register (rt712->component->dev, &mute_led_cdev[i]);
trigger_data looks like it's for the triggers, and the LED subsystem does overwrite it when configuring triggers.