Skip to contentSkip to conversation

drivers: sysreset: revert support for args in request

PATCH In review Quentin Schulz 2 participants 2 messages Jul 3

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 drivers: sysreset: revert support for args in request

From: Quentin Schulz <[email protected]>

This reverts:
- commit e49c84f7bb7b ("doc: usage: cmd: reset: specify when the -edl option is available")
- commit 1076feb8a3f9 ("cmd: boot: fix edl being shown when not supported")
- commit 63c806ba0e12 ("qcom_defconfig: enable psci based sysreset")
- commit ef06c5d76ff4 ("cmd: boot: Add '-edl' option to reset command documentation")
- commit 32825eaddc37 ("sysreset: Implement PSCI based reset to EDL mode for QCOM SoCs")
- commit fcb48b89813b ("drivers: sysreset: Add sysreset op that can take arguments")

There was a conflict reverting commit 63c806ba0e12 ("qcom_defconfig:
enable psci based sysreset") due to commit 02ef1859b44f ("configs:
Resync with savedefconfig"), but the conflict resolution was trivial.

The args support for the sysreset uclass contains a logic bug. The first sysreset device implementing the request_arg callback will consume the args, not support the specified arg and thus return -EPROTONOSUPPORT which will stop the iteration over all sysreset devices.

This is an issue if one has multiple sysreset devices and each with support for different (valid) args. If a sysreset device implements a -dummy argument and another -foo and a user calls reset -dummy from the U-Boot CLI, it'll depend on which sysreset device will be attempted first. If it is the one implementing -foo, it'll return it doesn't support the argument with -EPROTONOSUPPORT in which case the device implementing -dummy will never be attempted and instead we'll do a cold reset which is very likely not what's expected from the user.

Casey suggested[1] we revert this and start from scratch again with a different implementation instead.

[1] https://lore.kernel.org/u-boot/[email protected]/

---
Changes in v2:
- squashed all reverts into one big patch, as suggested by Marek and Tom
on IRC,
- added information about conflict during one revert in commit log,
- added Acked-by from Casey,
- Link to v1: https://patch.msgid.link/[email protected]

---
 cmd/boot.c                            |  6 -----
 configs/qcom_defconfig                |  2 --
 doc/usage/cmd/reset.rst               | 10 +-------
 drivers/firmware/psci.c               |  4 ----
 drivers/sysreset/Kconfig              | 15 ------------
 drivers/sysreset/Makefile             |  1 -
 drivers/sysreset/sysreset-uclass.c    | 37 ----------------------------
 drivers/sysreset/sysreset_qcom-psci.c | 45 -----------------------------------
 include/sysreset.h                    | 18 --------------
 9 files changed, 1 insertion(+), 137 deletions(-)
cmd/boot.c +0 -6
index 29cdf4a9a81a..23496cafdf5c 100644
@@ -60,12 +60,6 @@ U_BOOT_CMD(
 	reset, 2, 0,	do_reset,
 	"Perform RESET of the CPU",
 	"- cold boot without level specifier\n"
-#if IS_ENABLED(CONFIG_SYSRESET_CMD_RESET_ARGS)
-// All options handled by sysreset drivers via their sysreset_ops.request_arg callback
-#ifdef CONFIG_SYSRESET_QCOM_PSCI
-	"reset -edl - Boot to Emergency DownLoad mode\n"
-#endif
-#endif
 	"reset -w - warm reset if implemented"
 );
 
configs/qcom_defconfig +0 -2
index d0d54ec5a70b..b0d0f51b1c02 100644
@@ -133,8 +133,6 @@ CONFIG_QCOM_RPMH=y
 CONFIG_SPMI_MSM=y
 CONFIG_SYSINFO=y
 CONFIG_SYSINFO_SMBIOS=y
-CONFIG_SYSRESET_CMD_RESET_ARGS=y
-CONFIG_SYSRESET_QCOM_PSCI=y
 CONFIG_SYSRESET_QCOM_PSHOLD=y
 CONFIG_USB=y
 CONFIG_USB_XHCI_HCD=y
doc/usage/cmd/reset.rst +1 -9
index 79bc8b9deca5..78c9c8873bc9 100644
@@ -11,9 +11,7 @@ Synopsis
 
 ::
 
-    reset
-    reset -w
-    reset -edl
+    reset [-w]
 
 Description
 -----------
@@ -24,12 +22,6 @@ DDR and peripherals, on some boards also resets external PMIC.
 -w
     Do WARM reset: reset CPU but keep peripheral/DDR/PMIC active.
 
-All other options require CONFIG_SYSRESET_CMD_RESET_ARGS=y.
-
--edl
-    Boot to Emergency DownLoad mode on supported Qualcomm platforms. Unsupported
-    platforms will print an error message but the command will successfully
-    return (having done nothing). Requires CONFIG_SYSRESET_QCOM_PSCI=y.
 
 Return value
 ------------
drivers/firmware/psci.c +0 -4
index b6838a244d2b..2e3223e1c32a 100644
@@ -186,10 +186,6 @@ static int psci_bind(struct udevice *dev)
 					 NULL);
 		if (ret)
 			pr_debug("PSCI System Reset was not bound.\n");
-		if (IS_ENABLED(CONFIG_SYSRESET_QCOM_PSCI) &&
-		    device_bind_driver(dev, "qcom_psci-sysreset",
-				       "qcom_psci-sysreset", NULL))
-			pr_debug("QCOM PSCI System Reset was not bound.\n");
 	}
 
 	/* From PSCI v1.0 onward we can discover services through ARM_SMCCC_FEATURE */
drivers/sysreset/Kconfig +0 -15
index 90f740f51d42..16ef434a8d9c 100644
@@ -49,14 +49,6 @@ config SYSRESET_CMD_RESET
 	help
 	  Enable sysreset implementation of the reset command.
 
-config SYSRESET_CMD_RESET_ARGS
-	bool "Enable reset command to take arguments"
-	help
-	  Pass on the arguments received by the 'reset' command to the
-	  sysreset driver(s). The sysreset driver(s) may make use of the
-	  additional arguments for implementing arch/board specific
-	  functionality.
-
 if CMD_POWEROFF
 
 config SYSRESET_CMD_POWEROFF
@@ -301,13 +293,6 @@ config SYSRESET_RAA215300
 	help
 	  Add support for the system reboot via the Renesas RAA215300 PMIC.
 
-config SYSRESET_QCOM_PSCI
-	bool "Support reset to EDL for Qualcomm SoCs via PSCI"
-	depends on ARM_SMCCC
-	help
-	  Add support for the reset to EDL (Emergency Download) on Qualcomm
-	  SoCs via PSCI.
-
 config SYSRESET_QCOM_PSHOLD
 	bool "Support sysreset for Qualcomm SoCs via PSHOLD"
 	help
drivers/sysreset/Makefile +0 -1
index b5b99235b6ef..d18a5d523605 100644
@@ -30,7 +30,6 @@ obj-$(CONFIG_SYSRESET_RESETCTL) += sysreset_resetctl.o
 obj-$(CONFIG_$(PHASE_)SYSRESET_AT91) += sysreset_at91.o
 obj-$(CONFIG_$(PHASE_)SYSRESET_X86) += sysreset_x86.o
 obj-$(CONFIG_SYSRESET_RAA215300) += sysreset_raa215300.o
-obj-$(CONFIG_SYSRESET_QCOM_PSCI) += sysreset_qcom-psci.o
 obj-$(CONFIG_SYSRESET_QCOM_PSHOLD) += sysreset_qcom-pshold.o
 obj-$(CONFIG_TARGET_XTFPGA) += sysreset_xtfpga.o
 obj-$(CONFIG_SYSRESET_QEMU_VIRT_CTRL) += sysreset_qemu_virt_ctrl.o
drivers/sysreset/sysreset-uclass.c +0 -37
index f25e09e9cd06..536ac7271427 100644
@@ -32,18 +32,6 @@ int sysreset_request(struct udevice *dev, enum sysreset_t type)
 	return ops->request(dev, type);
 }
 
-#if IS_ENABLED(CONFIG_SYSRESET_CMD_RESET_ARGS)
-int sysreset_request_arg(struct udevice *dev, int argc, char * const argv[])
-{
-	struct sysreset_ops *ops = sysreset_get_ops(dev);
-
-	if (!ops->request_arg)
-		return -ENOSYS;
-
-	return ops->request_arg(dev, argc, argv);
-}
-#endif /* CONFIG_SYSRESET_CMD_RESET_ARGS */
-
 int sysreset_get_status(struct udevice *dev, char *buf, int size)
 {
 	struct sysreset_ops *ops = sysreset_get_ops(dev);
@@ -83,26 +71,6 @@ int sysreset_walk(enum sysreset_t type)
 	return ret;
 }
 
-#if IS_ENABLED(CONFIG_SYSRESET_CMD_RESET_ARGS)
-int sysreset_walk_arg(int argc, char * const argv[])
-{
-	struct udevice *dev;
-	int ret = -ENOSYS;
-
-	while (ret != -EINPROGRESS && ret != -EPROTONOSUPPORT) {
-		for (uclass_first_device(UCLASS_SYSRESET, &dev);
-		     dev;
-		     uclass_next_device(&dev)) {
-			ret = sysreset_request_arg(dev, argc, argv);
-			if (ret == -EINPROGRESS || ret == -EPROTONOSUPPORT)
-				break;
-		}
-	}
-
-	return ret;
-}
-#endif /* CONFIG_SYSRESET_CMD_RESET_ARGS */
-
 int sysreset_get_last_walk(void)
 {
 	struct udevice *dev;
@@ -164,11 +132,6 @@ int do_reset(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])
 	printf("resetting ...\n");
 	mdelay(100);
 
-#if IS_ENABLED(CONFIG_SYSRESET_CMD_RESET_ARGS)
-	if (argc > 1 && sysreset_walk_arg(argc, argv) == -EINPROGRESS)
-		return 0;
-#endif
-
 	sysreset_walk_halt(reset_type);
 
 	return 0;
drivers/sysreset/sysreset_qcom-psci.c deleted +0 -45

45 lines not on this page · raw message

include/sysreset.h +0 -18
index d1cc9ebc542a..ff20abdeed3c 100644
@@ -43,24 +43,6 @@ struct sysreset_ops {
 	 * (in which case this method will not actually return)
 	 */
 	int (*request)(struct udevice *dev, enum sysreset_t type);
-
-	/**
-	 * @request_arg: Reset handler implementations that might need to process
-	 *		 arguments given to the 'reset' command.
-	 *
-	 * Note that this function may return before the reset takes effect.
-	 *
-	 * @dev:	Device to be used for system reset
-	 * @argc:	No. of items in @argv
-	 * @argv:	Arguments given to 'reset' command
-	 * Return:
-	 * -EINPROGRESS		if the reset has started and will complete soon
-	 * -EPROTONOSUPPORT	if not supported by this device
-	 * 0			if the reset has already happened
-	 * (in which case this method will not actually return)
-	 */
-	int (*request_arg)(struct udevice *dev, int argc, char * const argv[]);
-
 	/**
 	 * @get_status:	get printable reset status information
 	 *

---
base-commit: f605dcee103c897b6f1a8873549a36949bd4e2a1
change-id: 20260702-revert-sysreset-4579ae458f2e

Best regards,

Signature · 1 line
Quentin Schulz <[email protected]>
#1 lore raw
Quoted 13 lines · Quentin Schulz

This reverts:
- commit e49c84f7bb7b ("doc: usage: cmd: reset: specify when the -edl option is available")
- commit 1076feb8a3f9 ("cmd: boot: fix edl being shown when not supported")
- commit 63c806ba0e12 ("qcom_defconfig: enable psci based sysreset")
- commit ef06c5d76ff4 ("cmd: boot: Add '-edl' option to reset command documentation")
- commit 32825eaddc37 ("sysreset: Implement PSCI based reset to EDL mode for QCOM SoCs")
- commit fcb48b89813b ("drivers: sysreset: Add sysreset op that can take arguments")

Quoted 1 line

[...]

Applied to u-boot/master, thanks!

[1/1] drivers: sysreset: revert support for args in request

      commit: c480bbd92b3273ecff5396da9221e7bcb08774ba
Signature · 1 line
Tom