dt-bindings: fix typos and brackets
Subsystems (23)
PATCH 1/1 dt-bindings: fix typos and brackets
Add missing '(', ')', '}'
Remove needless '(', ')', '{', '}'
'lover voltage' -> 'lower voltage'
Signed-off-by Manuel Ebner <[email protected]>
---
Sorry for the noise earlier.
--- Documentation/devicetree/bindings/arm/mediatek.yaml | 2 +- .../devicetree/bindings/arm/qcom,coresight-tpdm.yaml | 2 +- .../bindings/clock/renesas,rcar-usb2-clock-sel.yaml | 4 ++-- .../devicetree/bindings/input/gpio-charlieplex-keypad.yaml | 2 +- Documentation/devicetree/bindings/leds/backlight/88pm860x.txt | 1 + .../devicetree/bindings/memory-controllers/renesas,dbsc.yaml | 2 +- .../devicetree/bindings/memory-controllers/ti-aemif.txt | 4 ++-- Documentation/devicetree/bindings/mips/brcm/soc.txt | 2 +- Documentation/devicetree/bindings/mmc/sdhci-st.txt | 1 + Documentation/devicetree/bindings/phy/phy-miphy365x.txt | 2 +- Documentation/devicetree/bindings/powerpc/ibm,vas.txt | 2 +- Documentation/devicetree/bindings/regulator/max8907.txt | 1 - .../bindings/regulator/mediatek,mt6358-regulator.yaml | 2 +- .../devicetree/bindings/regulator/pbias-regulator.txt | 1 + .../devicetree/bindings/regulator/rohm,bd71837-regulator.yaml | 4 ++-- .../devicetree/bindings/regulator/rohm,bd71847-regulator.yaml | 4 ++-- .../devicetree/bindings/sound/mikroe,mikroe-proto.txt | 1 - Documentation/devicetree/bindings/usb/iproc-udc.txt | 1 + 18 files changed, 20 insertions(+), 18 deletions(-)
Documentation/devicetree/bindings/arm/mediatek.yaml +1 -1
@@ -314,7 +314,7 @@ properties: - const: google,steelix-sku196608 - const: google,steelix - const: mediatek,mt8186 - - description: Google Squirtle (Acer Chromebook Spin 311 (R724T) + - description: Google Squirtle (Acer Chromebook Spin 311 (R724T)) items: - const: google,squirtle - const: mediatek,mt8186
Documentation/devicetree/bindings/arm/qcom,coresight-tpdm.yaml +1 -1
@@ -9,7 +9,7 @@ title: Trace, Profiling and Diagnostics Monitor - TPDM description: | The TPDM or Monitor serves as data collection component for various dataset - types specified in the QPMDA spec. It covers Implementation defined ((ImplDef), + types specified in the QPMDA spec. It covers Implementation defined (ImplDef), Basic Counts (BC), Tenure Counts (TC), Continuous Multi-Bit (CMB), and Discrete Single Bit (DSB). It performs data collection in the data producing clock domain and transfers it to the data collection time domain, generally ATB
Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.yaml +2 -2
@@ -13,8 +13,8 @@ description: | If you connect an external clock to the USB_EXTAL pin only, you should set the clock rate to "usb_extal" node only. If you connect an oscillator to both the USB_XTAL and USB_EXTAL, this module - is not needed because this is default setting. (Of course, you can set the - clock rates to both "usb_extal" and "usb_xtal" nodes. + is not needed because this is default setting (Of course, you can set the + clock rates to both "usb_extal" and "usb_xtal" nodes). Case 1: An external clock connects to R-Car SoC +----------+ +--- R-Car ---------------------+
Documentation/devicetree/bindings/input/gpio-charlieplex-keypad.yaml +1 -1
@@ -11,7 +11,7 @@ maintainers: - Hugo Villeneuve <[email protected]> description: | - The charlieplex keypad supports N^2)-N different key combinations (where N is + The charlieplex keypad supports (N^2)-N different key combinations (where N is the number of I/O lines). Key presses and releases are detected by configuring only one line as output at a time, and reading other line states. This process is repeated for each line. Diodes are required to ensure current flows in only
Documentation/devicetree/bindings/leds/backlight/88pm860x.txt +1 -0
@@ -13,3 +13,4 @@ Example: }; backlight-2 { }; + };
Documentation/devicetree/bindings/memory-controllers/renesas,dbsc.yaml +1 -1
@@ -13,7 +13,7 @@ description: | Renesas SoCs contain one or more memory controllers. These memory controllers differ from one SoC variant to another, and are called by different names, e.g. "DDR Bus Controller (DBSC)", "DDR3 Bus State Controller - (DBSC3)", or "SDRAM Bus State Controller (SBSC)"). + (DBSC3)", or "SDRAM Bus State Controller (SBSC)". properties: compatible:
Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt +2 -2
@@ -111,7 +111,7 @@ Optional child cs node properties: - ti,cs-read-hold-ns: read hold width, ns Time between the deactivation of the read - strobe and the end of the cycle (which may be + strobe and the end of the cycle which may be either an address change or the deactivation of the chip select signal. Minimum value is 1 (0 treated as 1).
@@ -128,7 +128,7 @@ Optional child cs node properties: - ti,cs-write-hold-ns: write hold width, ns Time between the deactivation of the write - strobe and the end of the cycle (which may be + strobe and the end of the cycle which may be either an address change or the deactivation of the chip select signal. Minimum value is 1 (0 treated as 1).
Documentation/devicetree/bindings/mips/brcm/soc.txt +1 -1
@@ -45,7 +45,7 @@ each of which may have several associated hardware blocks, which are versioned independently (control registers, DDR PHYs, etc.). One might consider describing these controllers as a parent "memory controllers" block, which contains N sub-nodes (one for each controller in the system), each of which is -associated with a number of hardware register resources (e.g., its PHY. +associated with a number of hardware register resources (e.g., its PHY). == MEMC (MEMory Controller)
Documentation/devicetree/bindings/mmc/sdhci-st.txt +1 -0
@@ -71,6 +71,7 @@ mmc0: sdhci@fe81e000 { clock-names = "mmc"; clocks = <&clk_s_a1_ls 1>; bus-width = <8> +}; /* Example SD stih407 family configuration */
Documentation/devicetree/bindings/phy/phy-miphy365x.txt +1 -1
@@ -31,7 +31,7 @@ Required properties (port (child) node): Optional properties (port (child) node): - st,sata-gen : Generation of locally attached SATA IP. Expected values - are {1,2,3). If not supplied generation 1 hardware will + are (1,2,3). If not supplied generation 1 hardware will be expected - st,pcie-tx-pol-inv : Bool property to invert the polarity PCIe Tx (Txn/Txp) - st,sata-tx-pol-inv : Bool property to invert the polarity SATA Tx (Txn/Txp)
Documentation/devicetree/bindings/powerpc/ibm,vas.txt +1 -1
@@ -10,7 +10,7 @@ Required properties: - reg : Should contain 4 pairs of 64-bit fields specifying the Hypervisor window context start and length, OS/User window context start and length, "Paste address" start and length, "Paste window id" start bit and number - of bits) + of bits Example:
Documentation/devicetree/bindings/regulator/max8907.txt +0 -1
@@ -66,4 +66,3 @@ Example: ... }; }; - };
Documentation/devicetree/bindings/regulator/mediatek,mt6358-regulator.yaml +1 -1
@@ -145,7 +145,7 @@ allOf: then: patternProperties: # Old regulator node name scheme (with prefix and underscores) only - # ([^y-] is used to avoid matching -supply + # ([^y-]) is used to avoid matching -supply "^(?<!buck_)(?<!ldo_)v.*[^y-](?!-supply)$": false "^ldo_vsram-": false # vsram_core regulator doesn't exist on MT6358
Documentation/devicetree/bindings/regulator/pbias-regulator.txt +1 -0
@@ -30,3 +30,4 @@ Example: regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3000000>; }; + };
Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.yaml +2 -2
@@ -108,8 +108,8 @@ patternProperties: # Setups where regulator (especially the buck8) output voltage is scaled # by adding external connection where some other regulator output is # connected to feedback-pin (over suitable resistors) is getting popular - # amongst users of BD71837. (This allows for example scaling down the - # buck8 voltages to suit lover GPU voltages for projects where buck8 is + # amongst users of BD71837. This allows for example scaling down the + # buck8 voltages to suit lower GPU voltages for projects where buck8 is # (ab)used to supply power for GPU. # # So we allow describing this external connection from DT and scale the
Documentation/devicetree/bindings/regulator/rohm,bd71847-regulator.yaml +2 -2
@@ -103,8 +103,8 @@ patternProperties: # Setups where regulator (especially the buck8) output voltage is scaled # by adding external connection where some other regulator output is # connected to feedback-pin (over suitable resistors) is getting popular - # amongst users of BD71837. (This allows for example scaling down the - # buck8 voltages to suit lover GPU voltages for projects where buck8 is + # amongst users of BD71837. This allows for example scaling down the + # buck8 voltages to suit lower GPU voltages for projects where buck8 is # (ab)used to supply power for GPU. # # So we allow describing this external connection from DT and scale the
Documentation/devicetree/bindings/sound/mikroe,mikroe-proto.txt +0 -1
@@ -20,4 +20,3 @@ Example: audio-codec = <&wm8731>; dai-format = "i2s"; }; -};
Documentation/devicetree/bindings/usb/iproc-udc.txt +1 -0
@@ -19,3 +19,4 @@ Example: reg = <0x664e0000 0x2000>; interrupts = <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>; phys = <&usbdrd_phy>; + };
Signature · 1 line
2.54.0