Initial MSM8953 support
Subsystems (8)
cover Initial MSM8953 support
Add clock and pinctrl drivers for the MSM8953 SoC, and activate reserved memory carveout for MSM8953 and its sibling SDM632.
Note, that to boot successfully some more changes/quirks are needed:
* Decrease CONFIG_SYS_MALLOC_LEN to e.g. 0x1000000, default value crashes u-boot.
* Disable prng in msm8953.dtsi, crashes u-boot.
* Optionally disable probe of psci-sysreset driver, not functional on msm8953 and prohibits the pshold driver from getting active and working.
* Optionally add simple-framebuffer to sdm632-fairphone-fp3.dts, together with some lk2nd parameter this makes framebuffer somewhat functional. Have not played around too much to get that working 100%, since booting via lk2nd anyways is maybe one bootloader too much.
---
Luca Weiss (4):
clk/qcom: Add MSM8953 clock driver
qcom_defconfig: Enable MSM8953 clock driver
drivers: pinctrl: Add Qualcomm MSM8953 TLMM driver
mach-snapdragon: Do reserved memory carveout for MSM8953/SDM632
arch/arm/mach-snapdragon/board.c | 6 +- configs/qcom_defconfig | 1 + drivers/clk/qcom/Kconfig | 8 ++ drivers/clk/qcom/Makefile | 1 + drivers/clk/qcom/clock-msm8953.c | 141 +++++++++++++++++++++++++++++++++ drivers/pinctrl/qcom/Kconfig | 8 ++ drivers/pinctrl/qcom/Makefile | 1 + drivers/pinctrl/qcom/pinctrl-msm8953.c | 80 +++++++++++++++++++ 8 files changed, 244 insertions(+), 2 deletions(-)
---
base-commit: 501d76ca801343cce6dafb17740a8b679ed17072
change-id: 20260715-msm8953-basic-3bcd53790a65
Best regards,
Signature · 1 line
Luca Weiss <[email protected]>
PATCH 1/4 clk/qcom: Add MSM8953 clock driver
Add Clock driver for the GCC block found in the MSM8953 SoC.
--- drivers/clk/qcom/Kconfig | 8 +++ drivers/clk/qcom/Makefile | 1 + drivers/clk/qcom/clock-msm8953.c | 141 +++++++++++++++++++++++++++++++++++++++ 3 files changed, 150 insertions(+)
drivers/clk/qcom/Kconfig +8 -0
@@ -55,6 +55,14 @@ config CLK_QCOM_MILOS on the Snapdragon Milos SoC. This driver supports the clocks and resets exposed by the GCC hardware block. +config CLK_QCOM_MSM8953 + bool "Qualcomm MSM8953 GCC" + select CLK_QCOM + help + Say Y here to enable support for the Global Clock Controller + on the Snapdragon MSM8953 SoC. This driver supports the clocks + and resets exposed by the GCC hardware block. + config CLK_QCOM_QCM2290 bool "Qualcomm QCM2290 GCC" select CLK_QCOM
drivers/clk/qcom/Makefile +1 -0
@@ -10,6 +10,7 @@ obj-$(CONFIG_CLK_QCOM_IPQ4019) += clock-ipq4019.o obj-$(CONFIG_CLK_QCOM_IPQ5424) += clock-ipq5424.o obj-$(CONFIG_CLK_QCOM_IPQ9574) += clock-ipq9574.o obj-$(CONFIG_CLK_QCOM_MILOS) += clock-milos.o +obj-$(CONFIG_CLK_QCOM_MSM8953) += clock-msm8953.o obj-$(CONFIG_CLK_QCOM_QCM2290) += clock-qcm2290.o obj-$(CONFIG_CLK_QCOM_QCS404) += clock-qcs404.o obj-$(CONFIG_CLK_QCOM_QCS8300) += clock-qcs8300.o
drivers/clk/qcom/clock-msm8953.c new file +141 -0
141 lines not on this page · raw message
Signature · 1 line
2.55.0
PATCH 2/4 qcom_defconfig: Enable MSM8953 clock driver
In reply to Luca WeissEnable the driver so that MSM8953 devices can boot with qcom_defconfig.
--- configs/qcom_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/qcom_defconfig +1 -0
@@ -59,6 +59,7 @@ CONFIG_CLK_STUB=y CONFIG_CLK_QCOM_APQ8016=y CONFIG_CLK_QCOM_APQ8096=y CONFIG_CLK_QCOM_MILOS=y +CONFIG_CLK_QCOM_MSM8953=y CONFIG_CLK_QCOM_QCM2290=y CONFIG_CLK_QCOM_QCS404=y CONFIG_CLK_QCOM_QCS615=y
Signature · 1 line
2.55.0
PATCH 3/4 drivers: pinctrl: Add Qualcomm MSM8953 TLMM driver
In reply to Luca WeissAdd support for TLMM pin controller block (Top Level Mode Multiplexer) on MSM8953 SoC.
--- drivers/pinctrl/qcom/Kconfig | 8 ++++ drivers/pinctrl/qcom/Makefile | 1 + drivers/pinctrl/qcom/pinctrl-msm8953.c | 80 ++++++++++++++++++++++++++++++++++ 3 files changed, 89 insertions(+)
drivers/pinctrl/qcom/Kconfig +8 -0
@@ -62,6 +62,14 @@ config PINCTRL_QCOM_MILOS Say Y here to enable support for pinctrl on the Snapdragon Milos SoC, as well as the associated GPIO driver. +config PINCTRL_QCOM_MSM8953 + bool "Qualcomm MSM8953 Pinctrl" + default y if PINCTRL_QCOM_GENERIC + select PINCTRL_QCOM + help + Say Y here to enable support for pinctrl on the MSM8953 SoC, + as well as the associated GPIO driver. + config PINCTRL_QCOM_QCM2290 bool "Qualcomm QCM2290 Pinctrl" default y if PINCTRL_QCOM_GENERIC
drivers/pinctrl/qcom/Makefile +1 -0
@@ -9,6 +9,7 @@ obj-$(CONFIG_PINCTRL_QCOM_IPQ5424) += pinctrl-ipq5424.o obj-$(CONFIG_PINCTRL_QCOM_IPQ9574) += pinctrl-ipq9574.o obj-$(CONFIG_PINCTRL_QCOM_APQ8096) += pinctrl-apq8096.o obj-$(CONFIG_PINCTRL_QCOM_MILOS) += pinctrl-milos.o +obj-$(CONFIG_PINCTRL_QCOM_MSM8953) += pinctrl-msm8953.o obj-$(CONFIG_PINCTRL_QCOM_QCM2290) += pinctrl-qcm2290.o obj-$(CONFIG_PINCTRL_QCOM_QCS404) += pinctrl-qcs404.o obj-$(CONFIG_PINCTRL_QCOM_QCS615) += pinctrl-qcs615.o
drivers/pinctrl/qcom/pinctrl-msm8953.c new file +80 -0
80 lines not on this page · raw message
Signature · 1 line
2.55.0
PATCH 4/4 mach-snapdragon: Do reserved memory carveout for MSM8953/SDM632
In reply to Luca WeissThe MSM8953/SDM632 SoCs also requires the carveout, otherwise it crashes in early init in initcall_run_f -> board_init_f -> initcall_run_r -> initr_caches -> enable_caches -> dcache_enable -> mmu_setup -> set_sctlr.
--- arch/arm/mach-snapdragon/board.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)
arch/arm/mach-snapdragon/board.c +4 -2
@@ -745,8 +745,10 @@ void enable_caches(void) gd->arch.tlb_addr = tlb_addr; gd->arch.tlb_size = tlb_size; -/* We do the carveouts only for QCS404, for now. */ -if (fdt_node_check_compatible (gd->fdt_blob,0 ,"qcom,qcs404" ) ==0 ) { +/* We do the carveouts only for some SoCs, for now. */ +if (fdt_node_check_compatible (gd->fdt_blob,0 ,"qcom,qcs404" ) ==0 || +fdt_node_check_compatible (gd->fdt_blob,0 ,"qcom,msm8953" ) ==0 || +fdt_node_check_compatible (gd->fdt_blob,0 ,"qcom,sdm632" ) ==0 ) { carveout_start =get_timer (0 );/* Takes ~20-50ms on SDM845 */ carve_out_reserved_memory ();
Signature · 1 line
2.55.0