arm: dts: k3-am68-phyboard-izar-u-boot: Add mcu_i2c0
PATCH 1/2 arm: dts: k3-am68-phyboard-izar-u-boot: Add mcu_i2c0
Add mcu_i2c0 to access the pmic watchdog control registers.
Signed-off-by Dominik Haller <[email protected]>
--- arch/arm/dts/k3-am68-phyboard-izar-u-boot.dtsi | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-)
arch/arm/dts/k3-am68-phyboard-izar-u-boot.dtsi +15 -2
@@ -8,14 +8,27 @@ #include "k3-am68-phycore-som-binman.dtsi" +&wkup_pmx2 { + mcu_i2c0_pins_default: mcu-i2c0-default-pins { + pinctrl-single,pins = < + J721S2_WKUP_IOPAD(0x0a0, PIN_INPUT, 0) /* (G24) MCU_I2C0_SCL */ + J721S2_WKUP_IOPAD(0x0a4, PIN_INPUT, 0) /* (J25) MCU_I2C0_SDA */ + >; + }; +}; + &cbass_main { bootph-all; }; -&watchdog1 { - status = "disabled"; +&mcu_i2c0 { + status = "okay"; }; &mcu_uart0 { bootph-all; }; + +&watchdog1 { + status = "disabled"; +};
Signature · 1 line
2.43.0
PATCH 2/2 board: phytec: phycore_am68x: Turn off pmic watchdog
Starting with pmic firmware version 5 the watchdog is enabled with a timeout window of 13 minutes by default.
The TI EVMs use a dip switch to control a gpio on the pmic which gets configured as DISABLE_WDOG by the firmware.
On the phycore_am68x there is no such dip switch so pull resistors would be necessary. Using mcu_i2c0 to turn off the pmic watchdog works with all hardware and pmic firmware combinations.
Signed-off-by Dominik Haller <[email protected]>
--- board/phytec/phycore_am68x/phycore-am68x.c | 41 ++++++++++++++++++++++ configs/phycore_am68x_a72_defconfig | 1 - 2 files changed, 41 insertions(+), 1 deletion(-)
board/phytec/phycore_am68x/phycore-am68x.c +41 -0
@@ -21,6 +21,7 @@#include <dm/uclass-internal.h> #include <dm/root.h> #include <asm/arch/k3-ddr.h> +#include <i2c.h> DECLARE_GLOBAL_DATA_PTR ;
@@ -69,6 +70,46 @@ void spl_perform_board_fixups(struct spl_image_info *spl_image) }#endif +#define TPS6594_I2C_WD_ADDR 0x12 +#define WD_THR_CFG_REG 0x09 +#define WD_EN BIT(6) + +int tps6594_disable_watchdog (void ) +{ +struct udevice *i2c_bus, *i2c_dev; +int ret; +u8 val; + + ret =uclass_get_device_by_name (UCLASS_I2C ,"i2c@40b00000" , &i2c_bus); +if (ret) +return ret; + + ret =dm_i2c_probe (i2c_bus,TPS6594_I2C_WD_ADDR ,0 , &i2c_dev); +if (ret) +return ret; + + ret =dm_i2c_reg_read (i2c_dev,WD_THR_CFG_REG ); +if (ret <0 ) +return ret; + + val = (u8 )ret; + val &= ~WD_EN ; + ret =dm_i2c_reg_write (i2c_dev,WD_THR_CFG_REG , val); + +return ret; +} + +int board_init (void ) +{ +int ret; + + ret =tps6594_disable_watchdog (); +if (ret) +printf ("disabling TPS6594 watchdog failed: %d\n" , ret); + +return 0 ; +} +void spl_board_init (void ) {struct udevice *dev;
configs/phycore_am68x_a72_defconfig +0 -1
@@ -38,7 +38,6 @@ CONFIG_OF_SYSTEM_SETUP=y CONFIG_BOOTCOMMAND="bootflow scan -lb; run ${boot}boot" CONFIG_DEFAULT_FDT_FILE="oftree" CONFIG_LOGLEVEL=7 -# CONFIG_BOARD_INIT is not set CONFIG_SPL_MAX_SIZE=0xc0000 CONFIG_SPL_BOARD_INIT=y CONFIG_SPL_SYS_MALLOC_SIMPLE=y
Signature · 1 line
2.43.0
Quoted 3 lines · Dominik Haller
Add
mcu_i2c0to access the pmic watchdog control registers.
Applied to u-boot/main, thanks!
[1/2] arm: dts: k3-am68-phyboard-izar-u-boot: Add mcu_i2c0
commit: 1efe750e728e18fb37c1705d4ec3f6176ca3d9d5
[2/2] board: phytec: phycore_am68x: Turn off pmic watchdog
commit: cecee552a732500cf822c94014fdc56fddd1af4eSignature · 1 line
Tom