Skip to contentSkip to conversation

spi: spi-qpic-snand: Increase ECC strength for large OOB SPI-NAND devices

PATCH In review Md Sadre Alam 2 participants 2 messages Jul 16 – Jul 29 SPI

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 spi: spi-qpic-snand: Increase ECC strength for large OOB SPI-NAND devices

Some SPI-NAND devices with large OOB areas require a stronger ECC configuration than the default one provided through firmware description. For example, Macronix devices with a 256-byte OOB area report that 4-bit ECC is insufficient and trigger:

nand: WARNING: the ECC used on your system is too weak compared to the one required by the NAND chip

The QPIC SPI-NAND controller supports both 4-bit and 8-bit BCH ECC modes. When a device exposes an OOB area of at least 128 bytes, there is sufficient space to accommodate 8-bit ECC without exceeding the OOB layout constraints.

Automatically increase the ECC strength to 8 bits when the detected OOB size is 128 bytes or larger and the current configuration requests a weaker ECC level. This avoids ECC capability mismatches on devices that require stronger error correction and improves reliability.

---
 drivers/spi/spi-qpic-snand.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)
drivers/spi/spi-qpic-snand.c +13 -0
index 6cc53586b8a8..19812400124f 100644
@@ -274,6 +274,19 @@ static int qcom_spi_ecc_init_ctx_pipelined(struct nand_device *nand)
 		ecc_cfg->strength = 4;
 	}
 
+	/*
+	 * Override ECC strength based on OOB size to avoid weak ECC warning.
+	 * If OOB size is more than 128 bytes, use 8-bit ECC for better
+	 * error correction capability, which is required by chips with
+	 * larger OOB areas like Macronix SPI NAND with 256 bytes OOB.
+	 */
+	if (mtd->oobsize >= 128 && ecc_cfg->strength < 8) {
+		dev_info(snandc->dev,
+			 "Upgrading ECC strength from %d to 8 bits (OOB size: %d bytes)\n",
+			 ecc_cfg->strength, mtd->oobsize);
+		ecc_cfg->strength = 8;
+	}
+
 	if (ecc_cfg->step_size != NANDC_STEP_SIZE) {
 		dev_err(snandc->dev,
 			"only %u bytes ECC step size is supported\n",

---
base-commit: 19827e7930a5511c68e12aac6e4522f3661a1709
change-id: 20260716-8bitecc-b9be3d2e7690

Best regards,

Signature · 1 line
Md Sadre Alam <[email protected]>
maintainer
#1 lore raw
Quoted 1 line · Md Sadre Alam

spi: spi-qpic-snand: Increase ECC strength for large OOB SPI-NAND devices

Applied to

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-7.3

Thanks!

[1/1] spi: spi-qpic-snand: Increase ECC strength for large OOB SPI-NAND devices

      https://git.kernel.org/broonie/spi/c/ed4b52b24c55

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

Thanks,
Mark