x86/serial: Use generic BASE_BAUD in asm/serial.h

Include asm-generic/serial.h and use the generic BASE_BAUD definition instead of redefining it. Update the comment accordingly.

---
 arch/x86/include/asm/serial.h | 9 +--------
 include/asm-generic/serial.h  | 7 ++-----
 2 files changed, 3 insertions(+), 13 deletions(-)

index ece8299d2695..b623f6d70f64 100644
@@ -2,14 +2,7 @@
 #ifndef _ASM_X86_SERIAL_H
 #define _ASM_X86_SERIAL_H
 
-/*
- * This assumes you have a 1.8432 MHz clock for your UART.
- *
- * It'd be nice if someone built a serial card with a 24.576 MHz
- * clock, since the 16550A is capable of handling a top speed of 1.5
- * megabits/second; but this requires a faster clock.
- */
-#define BASE_BAUD (1843200/16)
+#include <asm-generic/serial.h>
 
 /* Standard COM flags (except for COM4, because of the 8514 problem) */
 #ifdef CONFIG_SERIAL_8250_DETECT_IRQ

index ca9f7b6be3f0..53b04e607972 100644
@@ -3,12 +3,9 @@
 #define __ASM_GENERIC_SERIAL_H
 
 /*
- * This should not be an architecture specific #define, oh well.
- *
- * Traditionally, it just describes i8250 and related serial ports
- * that have this clock rate.
+ * Default base baud for i8250 and related serial ports using a
+ * 1.8432 MHz UART clock.
  */
-
 #define BASE_BAUD (1843200 / 16)
 
 #endif /* __ASM_GENERIC_SERIAL_H */

You remove the important bit here, which is that we shouldn't need the definition in the first place.

Among the current references

arch/arc/include/asm/serial.h:#define BASE_BAUD arc_early_base_baud()
arch/arm/mach-omap1/board-ams-delta.c: .uartclk = BASE_BAUD * 16,
arch/loongarch/include/asm/serial.h:#define BASE_BAUD 0 arch/openrisc/include/asm/serial.h:#define BASE_BAUD (cpuinfo_or1k[smp_processor_id()].clock_frequency/16) arch/powerpc/include/asm/serial.h:#define BASE_BAUD ( 1843200 / 16 )
arch/powerpc/kernel/legacy_serial.c: u32 clock = BASE_BAUD * 16;
arch/x86/boot/early_serial_console.c:#define BASE_BAUD (1843200/16)
arch/x86/boot/early_serial_console.c: return BASE_BAUD / quot;
arch/xtensa/platforms/iss/include/platform/serial.h:#define BASE_BAUD 0 arch/xtensa/platforms/xt2000/include/platform/serial.h:#define BASE_BAUD ( DUART16552_XTAL_FREQ / 16 ) arch/xtensa/platforms/xtfpga/include/platform/serial.h:#define BASE_BAUD (*(long *)XTFPGA_CLKFRQ_VADDR / 16)
drivers/tty/serial/earlycon.c: port->uartclk = BASE_BAUD * 16;
include/asm-generic/serial.h:#define BASE_BAUD (1843200 / 16)

the only thing actually using it is the earlycon="..." command line parsing. As far as I can tell, everyone sets it to the generic value, except for loongarch/xtensa-iss using 0 to make 8250-early not override the default from the boot loader and arc/openrisc trying to do runtime detection. The arc/openrisc case can probably be fixed by just defining the clocks correctly in the dts files and using chosen/stdout-path instead of the open-coded earlycon settings. There is probably also a better solution to deal with the BASE_BAUD=0 case in an architecture-independent way.

I should also dig out my old series that turns the architecture specific SERIAL_PORT_DFNS macro into a regular driver.

Arnd