usb: atm: ueagle-atm: reject descriptors that confuse probe and disconnect

uea_probe() distinguishes a pre-firmware device from a post-firmware one using the USB id (UEA_IS_PREFIRM()), and stores a different object as the interface data in each case: a 'struct completion' for a pre-firmware device (to be waited on in .disconnect()), or a 'struct usbatm_data' for a post-firmware one.

uea_disconnect() instead tells the two apart by the number of interfaces of the active configuration (a pre-firmware device exposes a single interface, ADI930 has 2 and eagle has 3), and casts the interface data accordingly.

Because the two handlers use different criteria, a crafted device that advertises a pre-firmware id together with a multi-interface descriptor (or a post-firmware id with a single interface) makes them disagree: the small 'struct completion' stored by uea_probe() is then passed to usbatm_usb_disconnect(), which casts it to 'struct usbatm_data' and takes instance->serialize, reading past the end of the allocation:

  BUG: KASAN: slab-out-of-bounds in __mutex_lock+0x152a/0x1b80
  Read of size 8 at addr ffff8880470e2c60 by task kworker/1:2/982
  ...
   __mutex_lock+0x152a/0x1b80
   usbatm_usb_disconnect+0x70/0x820
   uea_disconnect+0x133/0x2c0
   usb_unbind_interface+0x1dd/0x9e0
  ...
  which belongs to the cache kmalloc-96 of size 96
  The buggy address is located 0 bytes to the right of
   allocated 96-byte region [ffff8880470e2c00, ffff8880470e2c60)

Reject such inconsistent descriptors in uea_probe() so that both handlers always make the same pre/post-firmware decision.

Reported-by [email protected]

Closes https://syzkaller.appspot.com/bug?extid=e62a973f8322b3bbe3ac

Fixes e2674dfbed8a ("usb: atm: ueagle-atm: wait for pre-firmware load in .disconnect()")

Signed-off-by Diego Fernando Mancera Gomez <[email protected]>

---
 drivers/usb/atm/ueagle-atm.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

drivers/usb/atm/ueagle-atm.c +17 -0

index 4e71ed679a76..4266a0cb7e3b 100644
@@ -2549,6 +2549,7 @@ static struct usbatm_driver uea_usbatm_driver = {
 static int uea_probe(struct usb_interface *intf, const struct usb_device_id *id)
 {
 	struct usb_device *usb = interface_to_usbdev(intf);
+	bool single_iface = usb->config->desc.bNumInterfaces == 1;
 	int ret;
 
 	uea_dbg(usb, "ADSL device found with vid (%#X) pid (%#X) Rev (%#X): %s\n",

@@ -2557,6 +2558,22 @@ static int uea_probe(struct usb_interface *intf, const struct usb_device_id *id)
 		le16_to_cpu(usb->descriptor.bcdDevice),
 		chip_name[UEA_CHIP_VERSION(id)]);
 
+	/*
+	 * uea_probe() decides between the pre-firmware and post-firmware case
+	 * from the USB id and stores a different object as interface data in
+	 * each case: a struct completion for a pre-firmware device, a struct
+	 * usbatm_data for a post-firmware one. uea_disconnect() instead tells
+	 * the two apart by the number of interfaces (a pre-firmware device
+	 * exposes a single interface, ADI930 has 2 and eagle has 3). A crafted
+	 * device advertising a pre-firmware id together with a multi-interface
+	 * descriptor (or the other way around) makes the two disagree, so that
+	 * usbatm_usb_disconnect() treats the small completion object as a
+	 * struct usbatm_data and reads out of bounds. Reject such inconsistent
+	 * descriptors so both paths make the same decision.
+	 */
+	if (UEA_IS_PREFIRM(id) != single_iface)
+		return -ENODEV;
+
 	usb_reset_device(usb);
 
 	if (UEA_IS_PREFIRM(id)) {

Signature · 1 line

2.43.0