Skip to contentSkip to conversation

mtd: spi-nor-ids: Add XMC XM25QH128C

PATCH Superseded Fabio Estevam via U-Boot 1 participant 10 messages Jul 22

Subsystems (3)

v2 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/5 mtd: spi-nor-ids: Add XMC XM25QH128C

From: Fabio Estevam <[email protected]>

Add the JEDEC ID for the XMC XM25QH128C SPI NOR flash.

This is a 128Mbit device using 64KiB sectors and supporting 4KiB erase, dual read and quad read, matching the other XM25QH128 variants.

---
Changes since v1:
- None.

 drivers/mtd/spi/spi-nor-ids.c | 1 +
 1 file changed, 1 insertion(+)
drivers/mtd/spi/spi-nor-ids.c +1 -0
index 31a2ba49a87c..90aa1025176c 100644
@@ -673,6 +673,7 @@ const struct flash_info spi_nor_ids[] = {
 	{ INFO("XM25QH64A", 0x207017, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 	{ INFO("XM25QH64C", 0x204017, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 	{ INFO("XM25QH128A", 0x207018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+	{ INFO("XM25QH128C", 0x204018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 	{ INFO("XM25QU128C", 0x204118, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 	{ INFO("XM25QH256C", 0x204019, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
 	{ INFO("XM25QU256C", 0x204119, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
Signature · 1 line
2.43.0
#1 lore raw

PATCH v2 2/5 rockchip: rk3399: Remove ROC-PC regulator overrides

From: Fabio Estevam <[email protected]>

The upstream devicetree already describes dc_12v as the output of the MP8859 regulator and drives the USB hub reset through the vcc5v0_host regulator pinctrl state.

Remove the legacy fixed-regulator overrides and rely on the upstream regulator descriptions.

---
Changes since v1:
- Newly introduced.

 arch/arm/dts/rk3399-roc-pc-u-boot.dtsi | 24 ------------------------
 1 file changed, 24 deletions(-)
arch/arm/dts/rk3399-roc-pc-u-boot.dtsi +0 -24
index 883d399a06a3..a85e9549c83e 100644
@@ -10,30 +10,6 @@
 	config {
 		sysreset-gpio = <&gpio1 RK_PA6 GPIO_ACTIVE_HIGH>;
 	};
-
-	vcc_hub_en: vcc_hub_en-regulator {
-		compatible = "regulator-fixed";
-		enable-active-high;
-		gpio = <&gpio2 RK_PA4 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&hub_rst>;
-		regulator-name = "vcc_hub_en";
-		regulator-always-on;
-	};
-};
-
-/*
- * should be placed inside mp8859, but not until mp8859 has
- * its own dt-binding.
- */
-&dc_12v {
-	compatible = "regulator-fixed";
-	regulator-name = "dc_12v";
-	regulator-always-on;
-	regulator-boot-on;
-	regulator-min-microvolt = <12000000>;
-	regulator-max-microvolt = <12000000>;
-	vin-supply = <&vcc_vbus_typec0>;
 };
 
 &gpio4 {
Signature · 1 line
2.43.0
author Reviewed-by Quentin Schulz on v2 2/5
#2 lore raw

Re: [PATCH v2 2/5] rockchip: rk3399: Remove ROC-PC regulator overrides

Hi Fabio,

Quoted 9 lines · Fabio Estevam via U-Boot

From: Fabio Estevam <[email protected]>

The upstream devicetree already describes dc_12v as the output of the MP8859 regulator and drives the USB hub reset through the vcc5v0_host regulator pinctrl state.

Remove the legacy fixed-regulator overrides and rely on the upstream regulator descriptions.

Thanks!
Quentin

#3 lore raw

PATCH v2 3/5 rockchip: rk3399: Add ROC-PC-PLUS board detection

In reply to Fabio Estevam via U-Boot

From: Fabio Estevam <[email protected]>

The ROC-RK3399-PC has an MP8859 regulator on I2C7 at address 0x66, while the ROC-RK3399-PC-PLUS does not. Probe for the regulator in SPL and use the result to select the matching devicetree from the U-Boot FIT. Fall back to the original board if the I2C bus cannot be probed.

Build both devicetrees from the existing roc-pc-rk3399_defconfig and enable the XMC SPI NOR driver used by the Plus variant. Set fdtfile from the selected U-Boot devicetree so the matching Linux devicetree is used as well.

---
Changes since v1:
- Added run-time board time detection.

 arch/arm/dts/rk3399-roc-pc-plus-u-boot.dtsi |  3 ++
 arch/arm/dts/rk3399-roc-pc-u-boot.dtsi      |  8 +++++
 board/firefly/roc-pc-rk3399/roc-pc-rk3399.c | 37 +++++++++++++++++++++
 configs/roc-pc-rk3399_defconfig             |  3 ++
 doc/board/rockchip/rockchip.rst             |  2 +-
 5 files changed, 52 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/rk3399-roc-pc-plus-u-boot.dtsi
arch/arm/dts/rk3399-roc-pc-plus-u-boot.dtsi new file +3 -0
new file mode 100644
index 000000000000..c80529a62b97
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk3399-roc-pc-u-boot.dtsi"
arch/arm/dts/rk3399-roc-pc-u-boot.dtsi +8 -0
index a85e9549c83e..e7e4a2c89072 100644
@@ -12,6 +12,14 @@
 	};
 };
 
+&i2c7 {
+	bootph-pre-ram;
+};
+
+&i2c7_xfer {
+	bootph-pre-ram;
+};
+
 &gpio4 {
 	bootph-pre-ram;
 };
board/firefly/roc-pc-rk3399/roc-pc-rk3399.c +37 -0
index 6937a27176f9..60a3ba43cdbd 100644
@@ -5,14 +5,24 @@
 
 #include <dm.h>
 #include <env.h>
+#include <fdtdec.h>
+#include <i2c.h>
+#include <image.h>
 #include <log.h>
 #include <spl_gpio.h>
+#include <asm/global_data.h>
 #include <asm/io.h>
 
 #include <asm/arch-rockchip/cru.h>
 #include <asm/arch-rockchip/gpio.h>
 #include <asm/arch-rockchip/grf_rk3399.h>
 
+#define ROC_PC_MP8859_BUS	"i2c@ff160000"
+#define ROC_PC_MP8859_ADDR	0x66
+#define ROC_PC_PLUS_FDTFILE	"rockchip/rk3399-roc-pc-plus.dtb"
+
+DECLARE_GLOBAL_DATA_PTR;
+
 #ifdef CONFIG_XPL_BUILD
 
 #define PMUGRF_BASE	0xff320000
@@ -54,4 +64,31 @@ void led_setup(void)
 	spl_gpio_output(gpio0, GPIO(BANK_B, 5), 1);
 }
 
+static bool is_roc_pc_plus(void)
+{
+	struct udevice *bus, *dev;
+
+	if (uclass_get_device_by_name(UCLASS_I2C, ROC_PC_MP8859_BUS, &bus))
+		return false;
+
+	return dm_i2c_probe(bus, ROC_PC_MP8859_ADDR, 0, &dev);
+}
+
+int board_fit_config_name_match(const char *name)
+{
+	if (is_roc_pc_plus())
+		return strcmp(name, ROC_PC_PLUS_FDTFILE);
+
+	return strcmp(name, CONFIG_DEFAULT_FDT_FILE);
+}
+
 #endif
+
+int rk_board_late_init(void)
+{
+	if (!fdt_node_check_compatible(gd->fdt_blob, 0,
+				       "firefly,roc-rk3399-pc-plus"))
+		env_set("fdtfile", ROC_PC_PLUS_FDTFILE);
+
+	return 0;
+}
configs/roc-pc-rk3399_defconfig +3 -0
index 1df5cb03adbb..6ef447e0e715 100644
@@ -3,12 +3,14 @@ CONFIG_SKIP_LOWLEVEL_INIT=y
 CONFIG_COUNTER_FREQUENCY=24000000
 CONFIG_ARCH_ROCKCHIP=y
 CONFIG_SPL_GPIO=y
+CONFIG_SPL_I2C=y
 CONFIG_NR_DRAM_BANKS=1
 CONFIG_SF_DEFAULT_SPEED=30000000
 CONFIG_ENV_SIZE=0x8000
 CONFIG_ENV_OFFSET=0x3F8000
 CONFIG_ENV_SECT_SIZE=0x1000
 CONFIG_DEFAULT_DEVICE_TREE="rockchip/rk3399-roc-pc"
+CONFIG_OF_LIST="rockchip/rk3399-roc-pc rockchip/rk3399-roc-pc-plus"
 CONFIG_DM_RESET=y
 CONFIG_ROCKCHIP_RK3399=y
 CONFIG_ROCKCHIP_SPI_IMAGE=y
@@ -48,6 +50,7 @@ CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_SDMA=y
 CONFIG_MMC_SDHCI_ROCKCHIP=y
 CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_XMC=y
 CONFIG_SPI_FLASH_WINBOND=y
 CONFIG_DM_ETH_PHY=y
 CONFIG_ETH_DESIGNWARE=y
doc/board/rockchip/rockchip.rst +1 -1
index 9351a5b8eae7..b565aea311e9 100644
@@ -81,7 +81,7 @@ List of mainline supported Rockchip boards:
      - 96boards RK3399 Ficus (ficus-rk3399)
      - 96boards Rock960 (rock960-rk3399)
      - Firefly-RK3399 (firefly_rk3399)
-     - Firefly ROC-RK3399-PC
+     - Firefly ROC-RK3399-PC/ROC-RK3399-PC-PLUS (roc-pc-rk3399)
      - FriendlyElec NanoPC-T4 (nanopc-t4-rk3399)
      - FriendlyElec NanoPi M4 (nanopi-m4-rk3399)
      - FriendlyElec NanoPi M4B (nanopi-m4b-rk3399)
Signature · 1 line
2.43.0
#4 lore raw

Re: [PATCH v2 3/5] rockchip: rk3399: Add ROC-PC-PLUS board detection

Hi Fabio,

Quoted 4 lines · Fabio Estevam via U-Boot

From: Fabio Estevam <[email protected]>

The ROC-RK3399-PC has an MP8859 regulator on I2C7 at address 0x66, while the ROC-RK3399-PC-PLUS does not. Probe for the regulator in SPL

The ROC-RK3399-PC-Pro also doesn't have one, so we'll need to figure out a way to differentiate them too (the day someone upstreams support for it :), we don't need to think about it today fortunately).

Quoted 97 lines

and use the result to select the matching devicetree from the U-Boot FIT. Fall back to the original board if the I2C bus cannot be probed.

Build both devicetrees from the existing roc-pc-rk3399_defconfig and enable the XMC SPI NOR driver used by the Plus variant. Set fdtfile from the selected U-Boot devicetree so the matching Linux devicetree is used as well.

---
Changes since v1:
- Added run-time board time detection.

  arch/arm/dts/rk3399-roc-pc-plus-u-boot.dtsi |  3 ++
  arch/arm/dts/rk3399-roc-pc-u-boot.dtsi      |  8 +++++
  board/firefly/roc-pc-rk3399/roc-pc-rk3399.c | 37 +++++++++++++++++++++
  configs/roc-pc-rk3399_defconfig             |  3 ++
  doc/board/rockchip/rockchip.rst             |  2 +-
  5 files changed, 52 insertions(+), 1 deletion(-)

create mode 100644 arch/arm/dts/rk3399-roc-pc-plus-u-boot.dtsi

arch/arm/dts/rk3399-roc-pc-plus-u-boot.dtsi new file +3 -0
new file mode 100644
index 000000000000..c80529a62b97
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk3399-roc-pc-u-boot.dtsi"
arch/arm/dts/rk3399-roc-pc-u-boot.dtsi +8 -0
index a85e9549c83e..e7e4a2c89072 100644
@@ -12,6 +12,14 @@
  	};
  };
 
+&i2c7 {
+	bootph-pre-ram;
+};
+
+&i2c7_xfer {
+	bootph-pre-ram;
+};
+
  &gpio4 {
  	bootph-pre-ram;
  };
board/firefly/roc-pc-rk3399/roc-pc-rk3399.c +25 -0
index 6937a27176f9..60a3ba43cdbd 100644
@@ -5,14 +5,24 @@
 
  #include <dm.h>
  #include <env.h>
+#include <fdtdec.h>
+#include <i2c.h>
+#include <image.h>
  #include <log.h>
  #include <spl_gpio.h>
+#include <asm/global_data.h>
  #include <asm/io.h>
 
  #include <asm/arch-rockchip/cru.h>
  #include <asm/arch-rockchip/gpio.h>
  #include <asm/arch-rockchip/grf_rk3399.h>
 
+#define ROC_PC_MP8859_BUS	"i2c@ff160000"
+#define ROC_PC_MP8859_ADDR	0x66
+#define ROC_PC_PLUS_FDTFILE	"rockchip/rk3399-roc-pc-plus.dtb"
+
+DECLARE_GLOBAL_DATA_PTR;
+
  #ifdef CONFIG_XPL_BUILD
 
  #define PMUGRF_BASE	0xff320000
@@ -54,4 +64,31 @@ void led_setup(void)
  	spl_gpio_output(gpio0, GPIO(BANK_B, 5), 1);
  }
 
+static bool is_roc_pc_plus(void)
+{
+	struct udevice *bus, *dev;
+
+	if (uclass_get_device_by_name(UCLASS_I2C, ROC_PC_MP8859_BUS, &bus))
+		return false;
+
+	return dm_i2c_probe(bus, ROC_PC_MP8859_ADDR, 0, &dev);
+}
+
+int board_fit_config_name_match(const char *name)
+{
+	if (is_roc_pc_plus())
+		return strcmp(name, ROC_PC_PLUS_FDTFILE);
+

board/firefly/roc-pc-rk3399/roc-pc-rk3399.c void led_setup(void) · line 91

Quoted 10 lines
board/firefly/roc-pc-rk3399/roc-pc-rk3399.c +9 -0
+	return strcmp(name, CONFIG_DEFAULT_FDT_FILE);
+}
+
  #endif
+
+int rk_board_late_init(void)
+{
+	if (!fdt_node_check_compatible(gd->fdt_blob, 0,
+				       "firefly,roc-rk3399-pc-plus"))
+		env_set("fdtfile", ROC_PC_PLUS_FDTFILE);

include/configs/rk3399_common.h sets fdtfile to CONFIG_DEFAULT_FDT_FILE (which is rockchip/rk3399-roc-pc.dtb for configs/roc-pc-rk3399_defconfig) by default so *not* setting it for the roc-rk3399-pc case means it'll use the default. We just hope someone doesn't save the environment on e.g. an SD card when having booted from a ROC-RK3399-PC-Plus and then insert it in a ROC-RK3399-PC... so maybe really set fdtfile for the roc-rk3399-pc case. What do you think?

Looks good to me otherwise, thanks!
Quentin

#5 lore raw

PATCH v2 4/5 rockchip: rk3399: Enable UMS on ROC-PC-PLUS

In reply to Fabio Estevam via U-Boot

From: Fabio Estevam <[email protected]>

Describe the USB3 OTG controller as a USB role switch and make peripheral mode the default when no external role provider has selected host mode. This retains OTG operation and both PHYs inherited from the SoC devicetree.

Enable the ums command so the onboard eMMC can be exposed as USB mass storage to a host.

---
Changes since v1:
- Add the same OTG description as submitted upstream:
https://lore.kernel.org/linux-arm-kernel/[email protected]/

 arch/arm/dts/rk3399-roc-pc-plus-u-boot.dtsi | 6 ++++++
 configs/roc-pc-rk3399_defconfig             | 1 +
 2 files changed, 7 insertions(+)
arch/arm/dts/rk3399-roc-pc-plus-u-boot.dtsi +6 -0
index c80529a62b97..73027335446e 100644
@@ -1,3 +1,9 @@
 // SPDX-License-Identifier: GPL-2.0+
 
 #include "rk3399-roc-pc-u-boot.dtsi"
+
+&usbdrd_dwc3_0 {
+	dr_mode = "otg";
+	role-switch-default-mode = "peripheral";
+	usb-role-switch;
+};
configs/roc-pc-rk3399_defconfig +1 -0
index 6ef447e0e715..127b71e97917 100644
@@ -36,6 +36,7 @@ CONFIG_CMD_BOOTZ=y
 CONFIG_CMD_GPT=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_TIME=y
 CONFIG_SPL_OF_CONTROL=y
Signature · 1 line
2.43.0
#6 lore raw

Re: [PATCH v2 4/5] rockchip: rk3399: Enable UMS on ROC-PC-PLUS

Hi Fabio,

Quoted 7 lines · Fabio Estevam via U-Boot

From: Fabio Estevam <[email protected]>

Describe the USB3 OTG controller as a USB role switch and make peripheral mode the default when no external role provider has selected host mode. This retains OTG operation and both PHYs inherited from the SoC devicetree.

Quoted 9 lines

Enable the ums command so the onboard eMMC can be exposed as USB mass storage to a host.

---
Changes since v1:
- Add the same OTG description as submitted upstream:
https://lore.kernel.org/linux-arm-kernel/[email protected]/

Thank you for sending this to the Linux kernel ML!

Quoted 9 lines
  arch/arm/dts/rk3399-roc-pc-plus-u-boot.dtsi | 6 ++++++
  configs/roc-pc-rk3399_defconfig             | 1 +
  2 files changed, 7 insertions(+)
arch/arm/dts/rk3399-roc-pc-plus-u-boot.dtsi +0 -0
index c80529a62b97..73027335446e 100644

arch/arm/dts/rk3399-roc-pc-plus-u-boot.dtsi line 9

Quoted 9 lines
arch/arm/dts/rk3399-roc-pc-plus-u-boot.dtsi +6 -0
@@ -1,3 +1,9 @@
  // SPDX-License-Identifier: GPL-2.0+
 
  #include "rk3399-roc-pc-u-boot.dtsi"
+
+&usbdrd_dwc3_0 {
+	dr_mode = "otg";
+	role-switch-default-mode = "peripheral";
+	usb-role-switch;
+};

Since this is not an important bug fix, I would prefer we wait it appears in devicetree-rebasing and cherry-pick then.

If there's a v3 (please note this series here is actually v3, you forgot to bump the version :) ), please drop it.

Cheers,
Quentin

#7 lore raw

PATCH v2 5/5 rockchip: roc-pc-rk3399: Enable redundant environment

In reply to Fabio Estevam via U-Boot

From: Fabio Estevam <[email protected]>

Use the final 64 KiB of the first 4 MiB of SPI NOR for two 32 KiB U-Boot environment copies. Place the primary copy at 0x3f0000 and the redundant copy at 0x3f8000.

Both copies are aligned to the 4 KiB erase-sector size and together occupy 0x3f0000 through 0x3fffff. Redundancy protects the environment against power loss or an interrupted update.

---
Changes since v1:
- Improved the commit log.

 configs/roc-pc-rk3399_defconfig | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
configs/roc-pc-rk3399_defconfig +3 -1
index 127b71e97917..8ded89c6388b 100644
@@ -7,7 +7,7 @@ CONFIG_SPL_I2C=y
 CONFIG_NR_DRAM_BANKS=1
 CONFIG_SF_DEFAULT_SPEED=30000000
 CONFIG_ENV_SIZE=0x8000
-CONFIG_ENV_OFFSET=0x3F8000
+CONFIG_ENV_OFFSET=0x3F0000
 CONFIG_ENV_SECT_SIZE=0x1000
 CONFIG_DEFAULT_DEVICE_TREE="rockchip/rk3399-roc-pc"
 CONFIG_OF_LIST="rockchip/rk3399-roc-pc rockchip/rk3399-roc-pc-plus"
@@ -19,6 +19,7 @@ CONFIG_SYS_LOAD_ADDR=0x800800
 CONFIG_SF_DEFAULT_BUS=1
 CONFIG_DEBUG_UART_BASE=0xFF1A0000
 CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_ENV_OFFSET_REDUND=0x3F8000
 CONFIG_SPL_SPI_FLASH_SUPPORT=y
 CONFIG_SPL_SPI=y
 CONFIG_DEBUG_UART=y
@@ -42,6 +43,7 @@ CONFIG_CMD_TIME=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
 CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_ENV_REDUNDANT=y
 CONFIG_ENV_RELOC_GD_ENV_ADDR=y
 CONFIG_ROCKCHIP_GPIO=y
 CONFIG_SYS_I2C_ROCKCHIP=y
Signature · 1 line
2.43.0
#8 lore raw

Re: [PATCH v2 5/5] rockchip: roc-pc-rk3399: Enable redundant environment

Hi Fabio,

Quoted 6 lines · Fabio Estevam via U-Boot

From: Fabio Estevam <[email protected]>

Use the final 64 KiB of the first 4 MiB of SPI NOR for two 32 KiB U-Boot environment copies. Place the primary copy at 0x3f0000 and the redundant copy at 0x3f8000.

Why do we need to move primary? Forgot to ask in v1 :)

This is fine otherwise, just being curious.

Thanks!
Quentin

#9 lore raw
In reply to Fabio Estevam via U-Boot

+Cc SPI-NOR maintainer and reviewer

Quoted 27 lines · Fabio Estevam via U-Boot

From: Fabio Estevam <[email protected]>

Add the JEDEC ID for the XMC XM25QH128C SPI NOR flash.

This is a 128Mbit device using 64KiB sectors and supporting 4KiB erase, dual read and quad read, matching the other XM25QH128 variants.

---
Changes since v1:
- None.

  drivers/mtd/spi/spi-nor-ids.c | 1 +
  1 file changed, 1 insertion(+)
drivers/mtd/spi/spi-nor-ids.c +1 -0
index 31a2ba49a87c..90aa1025176c 100644
@@ -673,6 +673,7 @@ const struct flash_info spi_nor_ids[] = {
  	{ INFO("XM25QH64A", 0x207017, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
  	{ INFO("XM25QH64C", 0x204017, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
  	{ INFO("XM25QH128A", 0x207018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+	{ INFO("XM25QH128C", 0x204018, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
  	{ INFO("XM25QU128C", 0x204118, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
  	{ INFO("XM25QH256C", 0x204019, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
  	{ INFO("XM25QU256C", 0x204119, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },