spi: dw: clean ups from "use threaded interrupt"
cover spi: dw: clean ups from "use threaded interrupt"
Two clean ups from the series "spi: dw: use threaded interrupt"
Hi Mark,
The enhanced spi mode was merged, I'm a bit concerned with potential bugs with "use threaded interrupt" with it, it's better to let the threaded interrupt tested with it. But I don't have available HW, so I will cook new version once v7.3-rc1 is out and ask sifive people help for test.
But the two clean ups in the "use threaded interrupt" series are ready so I pull them out of the series and rebase on latest spi-next tree, I hope they can be merged for v7.3-rc1.
Thanks in advance
Jisheng Zhang (2):
spi: dw: use DW_SPI_ISR directly
spi: dw: use DW_SPI_INT_MASK instead of hardcoded 0xff
drivers/spi/spi-dw-core.c | 19 ++++++++++--------- 1 file changed, 10 insertions(+), 9 deletions(-)
Signature · 1 line
2.53.0
PATCH 1/2 spi: dw: use DW_SPI_ISR directly
The DW_SPI_ISR register reports the masked interrupts, no need to mask again.
--- drivers/spi/spi-dw-core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/spi/spi-dw-core.c +1 -1
@@ -275,7 +275,7 @@ static irqreturn_t dw_spi_irq(int irq, void *dev_id) {struct spi_controller *ctlr = dev_id;struct dw_spi *dws =spi_controller_get_devdata (ctlr); -u16 irq_status =dw_readl (dws,DW_SPI_ISR ) &DW_SPI_INT_MASK ; +u16 irq_status =dw_readl (dws,DW_SPI_ISR );if (!irq_status)return IRQ_NONE ;
Signature · 1 line
2.53.0
PATCH 2/2 spi: dw: use DW_SPI_INT_MASK instead of hardcoded 0xff
In reply to Jisheng ZhangThe Interrupt Mask Register valid bits is bit[5:0] which is well defined with DW_SPI_INT_MASK, use it instead of the incorrect(but no harm) and hardcoded 0xff.
--- drivers/spi/spi-dw-core.c | 17 +++++++++-------- 1 file changed, 9 insertions(+), 8 deletions(-)
drivers/spi/spi-dw-core.c +9 -8
@@ -228,7 +228,7 @@ static irqreturn_t dw_spi_transfer_handler(struct dw_spi *dws)*/ dw_reader (dws);if (!dws->rx_len) { -dw_spi_mask_intr (dws,0xff ); +dw_spi_mask_intr (dws,DW_SPI_INT_MASK );spi_finalize_current_transfer (dws->ctlr); }else if (dws->rx_len <=dw_readl (dws,DW_SPI_RXFTLR )) {dw_writel (dws,DW_SPI_RXFTLR , dws->rx_len -1 );
@@ -264,7 +264,7 @@ static irqreturn_t dw_spi_enh_handler(struct dw_spi *dws)if (!dws->tx_len && dws->rx_len) {dw_spi_mask_intr (dws,DW_SPI_INT_TXEI ); }else if (!dws->rx_len && !dws->tx_len) { -dw_spi_mask_intr (dws,0xff ); +dw_spi_mask_intr (dws,DW_SPI_INT_MASK );spi_finalize_current_transfer (dws->ctlr); }
@@ -282,12 +282,13 @@ static irqreturn_t dw_spi_irq(int irq, void *dev_id)if (!dws->transfer_handler || (!ctlr->cur_msg && dws->transfer_handler == dw_spi_transfer_handler)) { -dw_spi_mask_intr (dws,0xff ); +dw_spi_mask_intr (dws,DW_SPI_INT_MASK );return IRQ_HANDLED ; } +if (dws->transfer_handler == dw_spi_enh_handler && !dws->rx_len && !dws->tx_len) { -dw_spi_mask_intr (dws,0xff ); +dw_spi_mask_intr (dws,DW_SPI_INT_MASK );spi_finalize_current_transfer (ctlr);return IRQ_HANDLED ; }
@@ -525,7 +526,7 @@ static int dw_spi_transfer_one(struct spi_controller *ctlr, dws->dma_mapped =spi_xfer_is_dma_mapped (ctlr, spi, transfer);/* For poll mode just disable all interrupts */ -dw_spi_mask_intr (dws,0xff ); +dw_spi_mask_intr (dws,DW_SPI_INT_MASK );if (dws->dma_mapped) { ret = dws->dma_ops->dma_setup (dws, transfer);
@@ -831,7 +832,7 @@ static int dw_spi_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)dw_spi_update_config (dws, mem->spi, &cfg,NULL ); -dw_spi_mask_intr (dws,0xff ); +dw_spi_mask_intr (dws,DW_SPI_INT_MASK );dw_spi_enable_chip (dws,1 );
@@ -999,7 +1000,7 @@ static int dw_spi_exec_enh_mem_op(struct spi_mem *mem, const struct spi_mem_op *dw_spi_update_config (dws, mem->spi, &cfg, &enh_cfg); -dw_spi_mask_intr (dws,0xff ); +dw_spi_mask_intr (dws,DW_SPI_INT_MASK );reinit_completion (&ctlr->xfer_completion);if (op->addr.nbytes && dws->set_addr_nbyte) {
@@ -1038,7 +1039,7 @@ static int dw_spi_exec_enh_mem_op(struct spi_mem *mem, const struct spi_mem_op * ms =wait_for_completion_timeout (&ctlr->xfer_completion,msecs_to_jiffies (ms));if (ms ==0 ) { -dw_spi_mask_intr (dws,0xff ); +dw_spi_mask_intr (dws,DW_SPI_INT_MASK );synchronize_irq (dws->irq); dws->rx =NULL ; dws->tx =NULL ;
Signature · 1 line
2.53.0
Mark Brown
maintainerRe: [PATCH 2/2] spi: dw: use DW_SPI_INT_MASK instead of hardcoded 0xff
drivers/spi/spi-dw-core.c static irqreturn_t dw_spi_transfer_handler(struct dw_spi *dws) · line 231
Quoted 8 lines · Jisheng Zhang
The Interrupt Mask Register valid bits is bit[5:0] which is well defined with
DW_SPI_INT_MASK, use it instead of the incorrect(but no harm) and hardcoded0xff.drivers/spi/spi-dw-core.c +1
-1dw_reader (dws);if (!dws->rx_len) { -dw_spi_mask_intr (dws,0xff ); +dw_spi_mask_intr (dws,DW_SPI_INT_MASK );
As I'm reasonably sure I said before this looks fairly obviously like defensive programming intended to handle future versions of the IP that define more mask bits sensibly.
Mark Brown
maintainerRe: (subset) [PATCH 0/2] spi: dw: clean ups from "use threaded interrupt"
In reply to Jisheng ZhangQuoted 6 lines · Jisheng Zhang
spi: dw: clean ups from "use threaded interrupt"
Two clean ups from the series "spi: dw: use threaded interrupt"
Hi Mark,
Quoted 7 lines
The enhanced spi mode was merged, I'm a bit concerned with potential bugs with "use threaded interrupt" with it, it's better to let the threaded interrupt tested with it. But I don't have available HW, so I will cook new version once v7.3-rc1 is out and ask sifive people help for test.
[...]
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-7.4
Thanks!
[1/2] spi: dw: use DW_SPI_ISR directly
https://git.kernel.org/broonie/spi/c/2f06fa7a4150
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark