Skip to contentSkip to conversation

net: phy: fix cleanup after probe failure

PATCH Applied Xuanqiang Luo 4 participants 11 messages Aug 23 – Aug 31

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

v5 cover net: phy: fix cleanup after probe failure

From: Xuanqiang Luo <[email protected]>

phy_probe() initializes the PHY driver, ports, SFP upstream, and LEDs in stages. Its error paths do not always release only the resources acquired at each stage. It can also mark the PHY ready before all setup succeeds.

Port setup also leaves SFP cleanup split between phy_sfp_probe(), phy_setup_ports(), and phy_probe(), and default port setup ignores errors from attaching the port to the PHY driver.

This series makes each initialization layer own its cleanup and propagates setup failures to the caller.

Patch 1 splits the phy_probe() cleanup by initialization stage.

Patch 2 makes SFP and port setup unwind their resources in the required order.

Patch 3 sets PHY_READY only after LED setup succeeds.

Patch 4 calls the PHY driver remove callback after later probe failures.

Patch 5 propagates errors from default port setup.

Patch 6 prevents a double-free after partial LED trigger registration.

---
Changes:
v5:
Patch 1:
- Describe the NULL-dereference path after a probe/remove cycle and add the corresponding Fixes tag. (Sashiko.)

Patch 5:
- Correct the Reviewed-by tag to Maxime Chevallier.

Patch 6:
- Mention the phy_remove() teardown path that can also trigger the double-free. (Sashiko.)

v4: https://lore.kernel.org/all/[email protected]/
Patch 1:
- Explain that LED triggers are initialized after the SFP upstream and ports, so they must be unwound first. (Andrew Lunn.)

Patch 2-5:
- Add Reviewed-by: Andrew Lunn <[email protected]>.

Patch 6 (new):
- Prevent a double-free after partial LED trigger registration and make the cleanup ownership explicit. (Sashiko.)

v3: https://lore.kernel.org/all/[email protected]/
Patch 1:
- Rename cleanup labels to include verbs describing their actions. (Jakub Kicinski.)

Patch 3:
- Do not clear phydev->drv before device-core teardown completes; this can expose NULL dereferences in concurrent attach paths and devres callbacks. Set PHY_READY only after LED setup succeeds and update the Fixes tag. (Sashiko, Jakub Kicinski.)

v2: https://lore.kernel.org/all/[email protected]/
Patch 1:
- Limit this patch to splitting phy_probe() error paths, moving the SFP teardown fixes to Patch 2.

Patch 2 (new):
- Make SFP and port setup unwind their resources in the required order.
- Add phy_sfp_release() for complete SFP teardown instead of open-coding sfp_bus_del_upstream(). (Andrew Lunn, Maxime Chevallier.)

Patch 3 (new):
- Restore PHY_DOWN and clear phydev->drv after probe failure.

Patch 4:
- Move the former Patch 2 to Patch 4; no functional changes.

Patch 5 (new):
- Propagate errors from default port setup.

v1: https://lore.kernel.org/all/[email protected]/

Xuanqiang Luo (6):
net: phy: split phy_probe() error paths
net: phy: unregister SFP upstream before port cleanup
net: phy: set PHY_READY after LED setup
net: phy: call driver remove when core initialization fails
net: phy: propagate errors from default port setup
net: phy: avoid double-free after LED trigger registration failure

 drivers/net/phy/phy_device.c       | 80 ++++++++++++++++++++++--------
 drivers/net/phy/phy_led_triggers.c | 11 ++--
 2 files changed, 65 insertions(+), 26 deletions(-)

base-commit: 746fc0787f616da418ffc04a110296fe95d53491

Signature · 1 line
2.43.0
#1 lore raw

PATCH v5 1/6 net: phy: split phy_probe() error paths

From: Xuanqiang Luo <[email protected]>

phy_probe() uses one cleanup path for failures at every initialization stage. This runs cleanup for resources that have not been initialized.

After a successful probe and remove, phy_led_triggers_unregister() can leave phy_num_led_triggers non-zero after freeing the trigger array. If a subsequent probe fails before LED trigger registration, the common error path calls phy_led_triggers_unregister() with a NULL array and stale count, causing a NULL dereference.

Split the cleanup by initialization stage so each failure path unwinds only the resources that may have been initialized. Unregister LED triggers before releasing the SFP upstream and ports, because the LED triggers are initialized after those resources and must be unwound first.

Fixes c8dbdc6e380e ("net: phy: register phy led_triggers during probe to avoid AB-BA deadlock")
---
 drivers/net/phy/phy_device.c | 20 +++++++++++---------
 1 file changed, 11 insertions(+), 9 deletions(-)
drivers/net/phy/phy_device.c +11 -9
index 94b2e85e00a37..2cf70471ae089 100644
@@ -3706,7 +3706,7 @@ static int phy_probe(struct device *dev)
 	if (phydev->drv->probe) {
 		err = phydev->drv->probe(phydev);
 		if (err)
-			goto out;
+			goto out_reset;
 	}
 
 	phy_disable_interrupts(phydev);
@@ -3727,7 +3727,7 @@ static int phy_probe(struct device *dev)
 		err = genphy_read_abilities(phydev);
 
 	if (err)
-		goto out;
+		goto out_reset;
 
 	if (!linkmode_test_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
 			       phydev->supported))
@@ -3744,7 +3744,7 @@ static int phy_probe(struct device *dev)
 
 	err = phy_setup_ports(phydev);
 	if (err)
-		goto out;
+		goto out_sfp_release;
 
 	phy_advertise_supported(phydev);
 
@@ -3753,7 +3753,7 @@ static int phy_probe(struct device *dev)
 	 */
 	err = genphy_c45_read_eee_adv(phydev, phydev->advertising_eee);
 	if (err)
-		goto out;
+		goto out_sfp_release;
 
 	/* Get the EEE modes we want to prohibit. */
 	of_set_phy_eee_broken(phydev);
@@ -3806,20 +3806,22 @@ static int phy_probe(struct device *dev)
 	if (IS_ENABLED(CONFIG_PHYLIB_LEDS) && !phy_driver_is_genphy(phydev)) {
 		err = of_phy_leds(phydev);
 		if (err)
-			goto out;
+			goto out_unreg_led_triggers;
 	}
 
 	return 0;
 
-out:
+out_unreg_led_triggers:
+	if (!phydev->is_on_sfp_module)
+		phy_led_triggers_unregister(phydev);
+
+out_sfp_release:
 	sfp_bus_del_upstream(phydev->sfp_bus);
 	phydev->sfp_bus = NULL;
 
 	phy_cleanup_ports(phydev);
 
-	if (!phydev->is_on_sfp_module)
-		phy_led_triggers_unregister(phydev);
-
+out_reset:
 	/* Re-assert the reset signal on error */
 	phy_device_reset(phydev, 1);
 
Signature · 1 line
2.43.0
Reviewed-by on v5 1/6
#2 lore raw

Re: [PATCH net v5 1/6] net: phy: split phy_probe() error paths

Hi,

Quoted 11 lines · Xuanqiang Luo

From: Xuanqiang Luo <[email protected]>

phy_probe() uses one cleanup path for failures at every initialization stage. This runs cleanup for resources that have not been initialized.

After a successful probe and remove, phy_led_triggers_unregister() can leave phy_num_led_triggers non-zero after freeing the trigger array. If a subsequent probe fails before LED trigger registration, the common error path calls phy_led_triggers_unregister() with a NULL array and stale count, causing a NULL dereference.

Quoted 7 lines

Split the cleanup by initialization stage so each failure path unwinds only the resources that may have been initialized. Unregister LED triggers before releasing the SFP upstream and ports, because the LED triggers are initialized after those resources and must be unwound first.

Fixes c8dbdc6e380e ("net: phy: register phy led_triggers during probe to avoid AB-BA deadlock")

Maxime

Quoted 72 lines
---
 drivers/net/phy/phy_device.c | 20 +++++++++++---------
 1 file changed, 11 insertions(+), 9 deletions(-)
drivers/net/phy/phy_device.c +11 -9
index 94b2e85e00a37..2cf70471ae089 100644
@@ -3706,7 +3706,7 @@ static int phy_probe(struct device *dev)
 	if (phydev->drv->probe) {
 		err = phydev->drv->probe(phydev);
 		if (err)
-			goto out;
+			goto out_reset;
 	}
 
 	phy_disable_interrupts(phydev);
@@ -3727,7 +3727,7 @@ static int phy_probe(struct device *dev)
 		err = genphy_read_abilities(phydev);
 
 	if (err)
-		goto out;
+		goto out_reset;
 
 	if (!linkmode_test_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
 			       phydev->supported))
@@ -3744,7 +3744,7 @@ static int phy_probe(struct device *dev)
 
 	err = phy_setup_ports(phydev);
 	if (err)
-		goto out;
+		goto out_sfp_release;
 
 	phy_advertise_supported(phydev);
 
@@ -3753,7 +3753,7 @@ static int phy_probe(struct device *dev)
 	 */
 	err = genphy_c45_read_eee_adv(phydev, phydev->advertising_eee);
 	if (err)
-		goto out;
+		goto out_sfp_release;
 
 	/* Get the EEE modes we want to prohibit. */
 	of_set_phy_eee_broken(phydev);
@@ -3806,20 +3806,22 @@ static int phy_probe(struct device *dev)
 	if (IS_ENABLED(CONFIG_PHYLIB_LEDS) && !phy_driver_is_genphy(phydev)) {
 		err = of_phy_leds(phydev);
 		if (err)
-			goto out;
+			goto out_unreg_led_triggers;
 	}
 
 	return 0;
 
-out:
+out_unreg_led_triggers:
+	if (!phydev->is_on_sfp_module)
+		phy_led_triggers_unregister(phydev);
+
+out_sfp_release:
 	sfp_bus_del_upstream(phydev->sfp_bus);
 	phydev->sfp_bus = NULL;
 
 	phy_cleanup_ports(phydev);
 
-	if (!phydev->is_on_sfp_module)
-		phy_led_triggers_unregister(phydev);
-
+out_reset:
 	/* Re-assert the reset signal on error */
 	phy_device_reset(phydev, 1);
 
#3 lore raw

PATCH v5 2/6 net: phy: unregister SFP upstream before port cleanup

In reply to Xuanqiang Luo

From: Xuanqiang Luo <[email protected]>

Commit 4497f5028675 ("net: phy: Clean the phy_ports after unregistering the downstream SFP bus") established that an SFP upstream must be unregistered before its phy_ports are destroyed because SFP callbacks may access these ports.

phy_setup_ports() does not follow this order when a later port setup step fails after phy_sfp_probe() succeeds. It destroys the SFP phy_port and leaves phy_probe() to unregister the upstream later, creating a race between port destruction and SFP upstream callbacks.

The error unwind is also split across three functions. If phy_setup_sfp_port() fails, phy_sfp_probe() leaves the upstream registered and relies on phy_probe() to remove it after phy_setup_ports() returns.

Make each layer unwind the resources it successfully set up. Unregister only the upstream in phy_sfp_probe() when SFP port setup fails, since the failed port has already been destroyed. Add phy_sfp_release() for a successful SFP probe, and make phy_setup_ports() use it before cleaning up the remaining ports. Once phy_setup_ports() has rolled back all port setup, make phy_probe() skip this cleanup.

Fixes 589e934d2735 ("net: phy: Introduce PHY ports representation")
---
 drivers/net/phy/phy_device.c | 49 ++++++++++++++++++++++++++++--------
 1 file changed, 38 insertions(+), 11 deletions(-)
drivers/net/phy/phy_device.c +38 -11
index 2cf70471ae089..4b9b2300422fb 100644
@@ -1723,12 +1723,41 @@ static int phy_sfp_probe(struct phy_device *phydev)
 			phydev->sfp_bus = NULL;
 	}
 
-	if (!ret && phydev->sfp_bus)
+	if (!ret && phydev->sfp_bus) {
 		ret = phy_setup_sfp_port(phydev);
+		if (ret) {
+			sfp_bus_del_upstream(phydev->sfp_bus);
+			phydev->sfp_bus = NULL;
+		}
+	}
 
 	return ret;
 }
 
+/**
+ * phy_sfp_release - release resources set up by phy_sfp_probe()
+ * @phydev: the PHY device
+ *
+ * Release the SFP resources set up by a successful phy_sfp_probe(). Unregister
+ * the upstream before destroying its phy_port, so SFP upstream callbacks cannot
+ * race with port destruction.
+ */
+static void phy_sfp_release(struct phy_device *phydev)
+{
+	struct phy_port *port, *tmp;
+
+	sfp_bus_del_upstream(phydev->sfp_bus);
+	phydev->sfp_bus = NULL;
+
+	list_for_each_entry_safe(port, tmp, &phydev->ports, head) {
+		if (!port->is_sfp)
+			continue;
+
+		phy_del_port(phydev, port);
+		phy_port_destroy(port);
+	}
+}
+
 static bool phy_drv_supports_irq(const struct phy_driver *phydrv)
 {
 	return phydrv->config_intr && phydrv->handle_interrupt;
@@ -3547,13 +3576,13 @@ static int phy_setup_ports(struct phy_device *phydev)
 	if (!phydev->is_genphy_driven) {
 		ret = phy_sfp_probe(phydev);
 		if (ret)
-			goto out;
+			goto err_ports;
 	}
 
 	if (phydev->n_ports < phydev->max_n_ports) {
 		ret = phy_default_setup_single_port(phydev);
 		if (ret)
-			goto out;
+			goto err_sfp;
 	}
 
 	linkmode_zero(ports_supported);
@@ -3580,7 +3609,9 @@ static int phy_setup_ports(struct phy_device *phydev)
 
 	return 0;
 
-out:
+err_sfp:
+	phy_sfp_release(phydev);
+err_ports:
 	phy_cleanup_ports(phydev);
 	return ret;
 }
@@ -3744,7 +3775,7 @@ static int phy_probe(struct device *dev)
 
 	err = phy_setup_ports(phydev);
 	if (err)
-		goto out_sfp_release;
+		goto out_reset;
 
 	phy_advertise_supported(phydev);
 
@@ -3816,9 +3847,7 @@ static int phy_probe(struct device *dev)
 		phy_led_triggers_unregister(phydev);
 
 out_sfp_release:
-	sfp_bus_del_upstream(phydev->sfp_bus);
-	phydev->sfp_bus = NULL;
-
+	phy_sfp_release(phydev);
 	phy_cleanup_ports(phydev);
 
 out_reset:
@@ -3842,9 +3871,7 @@ static int phy_remove(struct device *dev)
 
 	phydev->state = PHY_DOWN;
 
-	sfp_bus_del_upstream(phydev->sfp_bus);
-	phydev->sfp_bus = NULL;
-
+	phy_sfp_release(phydev);
 	phy_cleanup_ports(phydev);
 
 	if (phydev->drv && phydev->drv->remove)
Signature · 1 line
2.43.0
Reviewed-by on v5 2/6
#4 lore raw

Re: [PATCH net v5 2/6] net: phy: unregister SFP upstream before port cleanup

Hi,

Quoted 24 lines · Xuanqiang Luo

From: Xuanqiang Luo <[email protected]>

Commit 4497f5028675 ("net: phy: Clean the phy_ports after unregistering the downstream SFP bus") established that an SFP upstream must be unregistered before its phy_ports are destroyed because SFP callbacks may access these ports.

phy_setup_ports() does not follow this order when a later port setup step fails after phy_sfp_probe() succeeds. It destroys the SFP phy_port and leaves phy_probe() to unregister the upstream later, creating a race between port destruction and SFP upstream callbacks.

The error unwind is also split across three functions. If phy_setup_sfp_port() fails, phy_sfp_probe() leaves the upstream registered and relies on phy_probe() to remove it after phy_setup_ports() returns.

Make each layer unwind the resources it successfully set up. Unregister only the upstream in phy_sfp_probe() when SFP port setup fails, since the failed port has already been destroyed. Add phy_sfp_release() for a successful SFP probe, and make phy_setup_ports() use it before cleaning up the remaining ports. Once phy_setup_ports() has rolled back all port setup, make phy_probe() skip this cleanup.

Quoted 3 lines
Fixes 589e934d2735 ("net: phy: Introduce PHY ports representation")

Thanks for this cleanup,

Maxime

Quoted 109 lines
---
 drivers/net/phy/phy_device.c | 49 ++++++++++++++++++++++++++++--------
 1 file changed, 38 insertions(+), 11 deletions(-)
drivers/net/phy/phy_device.c +38 -11
index 2cf70471ae089..4b9b2300422fb 100644
@@ -1723,12 +1723,41 @@ static int phy_sfp_probe(struct phy_device *phydev)
 			phydev->sfp_bus = NULL;
 	}
 
-	if (!ret && phydev->sfp_bus)
+	if (!ret && phydev->sfp_bus) {
 		ret = phy_setup_sfp_port(phydev);
+		if (ret) {
+			sfp_bus_del_upstream(phydev->sfp_bus);
+			phydev->sfp_bus = NULL;
+		}
+	}
 
 	return ret;
 }
 
+/**
+ * phy_sfp_release - release resources set up by phy_sfp_probe()
+ * @phydev: the PHY device
+ *
+ * Release the SFP resources set up by a successful phy_sfp_probe(). Unregister
+ * the upstream before destroying its phy_port, so SFP upstream callbacks cannot
+ * race with port destruction.
+ */
+static void phy_sfp_release(struct phy_device *phydev)
+{
+	struct phy_port *port, *tmp;
+
+	sfp_bus_del_upstream(phydev->sfp_bus);
+	phydev->sfp_bus = NULL;
+
+	list_for_each_entry_safe(port, tmp, &phydev->ports, head) {
+		if (!port->is_sfp)
+			continue;
+
+		phy_del_port(phydev, port);
+		phy_port_destroy(port);
+	}
+}
+
 static bool phy_drv_supports_irq(const struct phy_driver *phydrv)
 {
 	return phydrv->config_intr && phydrv->handle_interrupt;
@@ -3547,13 +3576,13 @@ static int phy_setup_ports(struct phy_device *phydev)
 	if (!phydev->is_genphy_driven) {
 		ret = phy_sfp_probe(phydev);
 		if (ret)
-			goto out;
+			goto err_ports;
 	}
 
 	if (phydev->n_ports < phydev->max_n_ports) {
 		ret = phy_default_setup_single_port(phydev);
 		if (ret)
-			goto out;
+			goto err_sfp;
 	}
 
 	linkmode_zero(ports_supported);
@@ -3580,7 +3609,9 @@ static int phy_setup_ports(struct phy_device *phydev)
 
 	return 0;
 
-out:
+err_sfp:
+	phy_sfp_release(phydev);
+err_ports:
 	phy_cleanup_ports(phydev);
 	return ret;
 }
@@ -3744,7 +3775,7 @@ static int phy_probe(struct device *dev)
 
 	err = phy_setup_ports(phydev);
 	if (err)
-		goto out_sfp_release;
+		goto out_reset;
 
 	phy_advertise_supported(phydev);
 
@@ -3816,9 +3847,7 @@ static int phy_probe(struct device *dev)
 		phy_led_triggers_unregister(phydev);
 
 out_sfp_release:
-	sfp_bus_del_upstream(phydev->sfp_bus);
-	phydev->sfp_bus = NULL;
-
+	phy_sfp_release(phydev);
 	phy_cleanup_ports(phydev);
 
 out_reset:
@@ -3842,9 +3871,7 @@ static int phy_remove(struct device *dev)
 
 	phydev->state = PHY_DOWN;
 
-	sfp_bus_del_upstream(phydev->sfp_bus);
-	phydev->sfp_bus = NULL;
-
+	phy_sfp_release(phydev);
 	phy_cleanup_ports(phydev);
 
 	if (phydev->drv && phydev->drv->remove)
#5 lore raw

PATCH v5 3/6 net: phy: set PHY_READY after LED setup

In reply to Xuanqiang Luo

From: Xuanqiang Luo <[email protected]>

phy_probe() sets PHY_READY before calling of_phy_leds(). If LED setup fails, the error path releases the initialized resources while the PHY state remains READY even though probing failed.

Set PHY_READY only after LED setup succeeds.

Fixes 01e5b728e9e4 ("net: phy: Add a binding for PHY LEDs")
---
 drivers/net/phy/phy_device.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/net/phy/phy_device.c +3 -3
index 4b9b2300422fb..891df46d0597f 100644
@@ -3824,9 +3824,6 @@ static int phy_probe(struct device *dev)
 				 phydev->supported);
 	}
 
-	/* Set the state to READY by default */
-	phydev->state = PHY_READY;
-
 	/* Register the PHY LED triggers */
 	if (!phydev->is_on_sfp_module)
 		phy_led_triggers_register(phydev);
@@ -3840,6 +3837,9 @@ static int phy_probe(struct device *dev)
 			goto out_unreg_led_triggers;
 	}
 
+	/* Set the state to READY by default */
+	phydev->state = PHY_READY;
+
 	return 0;
 
 out_unreg_led_triggers:
Signature · 1 line
2.43.0
#6 lore raw

PATCH v5 4/6 net: phy: call driver remove when core initialization fails

In reply to Xuanqiang Luo

From: Xuanqiang Luo <[email protected]>

phy_probe() may fail while querying features or completing other core initialization after the PHY driver probe callback has succeeded. The driver core does not run the remove path after a probe error, so resources that the PHY driver releases in its remove callback are leaked.

Call the PHY driver remove callback on these failures.

Fixes efbdfdc29bdd ("net: phy: Add support for asking the PHY its abilities")
---
 drivers/net/phy/phy_device.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)
drivers/net/phy/phy_device.c +6 -2
index 891df46d0597f..691396794decd 100644
@@ -3758,7 +3758,7 @@ static int phy_probe(struct device *dev)
 		err = genphy_read_abilities(phydev);
 
 	if (err)
-		goto out_reset;
+		goto out_remove;
 
 	if (!linkmode_test_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
 			       phydev->supported))
@@ -3775,7 +3775,7 @@ static int phy_probe(struct device *dev)
 
 	err = phy_setup_ports(phydev);
 	if (err)
-		goto out_reset;
+		goto out_remove;
 
 	phy_advertise_supported(phydev);
 
@@ -3850,6 +3850,10 @@ static int phy_probe(struct device *dev)
 	phy_sfp_release(phydev);
 	phy_cleanup_ports(phydev);
 
+out_remove:
+	if (phydev->drv->remove)
+		phydev->drv->remove(phydev);
+
 out_reset:
 	/* Re-assert the reset signal on error */
 	phy_device_reset(phydev, 1);
Signature · 1 line
2.43.0
#7 lore raw

PATCH v5 5/6 net: phy: propagate errors from default port setup

In reply to Xuanqiang Luo

From: Xuanqiang Luo <[email protected]>

phy_default_setup_single_port() ignores errors from phy_add_port() and always reports success. If a PHY driver attach_mdi_port() callback fails, the phy_port is leaked and PHY probing continues without the expected default port.

Destroy the port and return the error.

Fixes 589e934d2735 ("net: phy: Introduce PHY ports representation")
---
 drivers/net/phy/phy_device.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/net/phy/phy_device.c +5 -2
index 691396794decd..8cb0d60fcbba9 100644
@@ -3483,6 +3483,7 @@ static int phy_default_setup_single_port(struct phy_device *phydev)
 {
 	struct phy_port *port = phy_port_alloc();
 	unsigned long mode;
+	int ret;
 
 	if (!port)
 		return -ENOMEM;
@@ -3509,9 +3510,11 @@ static int phy_default_setup_single_port(struct phy_device *phydev)
 		port->pairs = max_t(int, port->pairs,
 				    ethtool_linkmode_n_pairs(mode));
 
-	phy_add_port(phydev, port);
+	ret = phy_add_port(phydev, port);
+	if (ret)
+		phy_port_destroy(port);
 
-	return 0;
+	return ret;
 }
 
 static int of_phy_ports(struct phy_device *phydev)
Signature · 1 line
2.43.0
#8 lore raw

PATCH v5 6/6 net: phy: avoid double-free after LED trigger registration failure

In reply to Xuanqiang Luo

From: Xuanqiang Luo <[email protected]>

phy_led_triggers_register() frees phy_led_triggers when a speed trigger registration fails, but leaves the pointer set to the freed allocation before clearing phy_num_led_triggers.

phy_probe() ignores the registration error. If a later probe step fails, its error path calls phy_led_triggers_unregister(); normal teardown during an unbind or MDIO bus removal calls the same helper from phy_remove(). In either case, the trigger count is zero, so the per-trigger unregister loop is skipped, but the dangling pointer is still freed unconditionally.

Clear the pointer when partial registration cleanup frees the array, and make phy_led_triggers_unregister() free the array only when its pointer is non-NULL.

Fixes b7f0ee992adf ("net: phy: leds: fix memory leak")
---
 drivers/net/phy/phy_led_triggers.c | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)
drivers/net/phy/phy_led_triggers.c +7 -4
index 4eb7716bb9d6c..ff6e518395be0 100644
@@ -126,6 +126,7 @@ int phy_led_triggers_register(struct phy_device *phy)
 	while (i--)
 		phy_led_trigger_unregister(&phy->phy_led_triggers[i]);
 	kfree(phy->phy_led_triggers);
+	phy->phy_led_triggers = NULL;
 out_unreg_link:
 	phy_led_trigger_unregister(phy->led_link_trigger);
 out_free_link:
@@ -141,10 +142,12 @@ void phy_led_triggers_unregister(struct phy_device *phy)
 {
 	int i;
 
-	for (i = 0; i < phy->phy_num_led_triggers; i++)
-		phy_led_trigger_unregister(&phy->phy_led_triggers[i]);
-	kfree(phy->phy_led_triggers);
-	phy->phy_led_triggers = NULL;
+	if (phy->phy_led_triggers) {
+		for (i = 0; i < phy->phy_num_led_triggers; i++)
+			phy_led_trigger_unregister(&phy->phy_led_triggers[i]);
+		kfree(phy->phy_led_triggers);
+		phy->phy_led_triggers = NULL;
+	}
 
 	if (phy->led_link_trigger) {
 		phy_led_trigger_unregister(phy->led_link_trigger);
Signature · 1 line
2.43.0
maintainer
#9 lore raw

Re: [PATCH net v5 6/6] net: phy: avoid double-free after LED trigger registration failure

Quoted 12 lines · Xuanqiang Luo

From: Xuanqiang Luo <[email protected]>

phy_led_triggers_register() frees phy_led_triggers when a speed trigger registration fails, but leaves the pointer set to the freed allocation before clearing phy_num_led_triggers.

phy_probe() ignores the registration error. If a later probe step fails, its error path calls phy_led_triggers_unregister(); normal teardown during an unbind or MDIO bus removal calls the same helper from phy_remove(). In either case, the trigger count is zero, so the per-trigger unregister loop is skipped, but the dangling pointer is still freed unconditionally.

Quoted 6 lines

Clear the pointer when partial registration cleanup frees the array, and make phy_led_triggers_unregister() free the array only when its pointer is non-NULL.

Fixes b7f0ee992adf ("net: phy: leds: fix memory leak")

I think an explicit ack from phy experts is needed here: sashiko has flagged a few pre-existing issues on this patch:

https://netdev-ai.bots.linux.dev/sashiko/#/patchset/20260823035600.188864-1-xuanqiang.luo%40linux.dev

that IMHO bortderline to be addresses in this same series.

/P

#10 lore raw
In reply to Xuanqiang Luo
This series was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:

Hello:

This series was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:

Quoted 11 lines · On Sun, 23 Aug 2026 11:55:54 +0800 you wrote:

From: Xuanqiang Luo <[email protected]>

phy_probe() initializes the PHY driver, ports, SFP upstream, and LEDs in stages. Its error paths do not always release only the resources acquired at each stage. It can also mark the PHY ready before all setup succeeds.

Port setup also leaves SFP cleanup split between phy_sfp_probe(), phy_setup_ports(), and phy_probe(), and default port setup ignores errors from attaching the port to the PHY driver.

[...]

Here is the summary with links:
- [net,v5,1/6] net: phy: split phy_probe() error paths

    https://git.kernel.org/netdev/net-next/c/b6d201d97145
  - [net,v5,2/6] net: phy: unregister SFP upstream before port cleanup
    https://git.kernel.org/netdev/net-next/c/f558204abcb9
  - [net,v5,3/6] net: phy: set PHY_READY after LED setup
    https://git.kernel.org/netdev/net-next/c/52dd7eb1a33e
  - [net,v5,4/6] net: phy: call driver remove when core initialization fails
    https://git.kernel.org/netdev/net-next/c/afd5aecd3c07
  - [net,v5,5/6] net: phy: propagate errors from default port setup
    https://git.kernel.org/netdev/net-next/c/48378efebbe7
  - [net,v5,6/6] net: phy: avoid double-free after LED trigger registration failure
    https://git.kernel.org/netdev/net-next/c/f7f619ecda57

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html