int3472: unhandled GPIO type 0x08 leaves the rear camera dead (Surface Pro 11, Intel)
Subsystems (2)
Hello,
On a Microsoft Surface Pro 11 for Business (Intel, Lunar Lake) the rear camera does not work, and it traces to a single unhandled GPIO type in int3472-discrete.
int3472-discrete INT3472:00: GPIO type 0x08 unknown;
the sensor may not work
ov13858 i2c-OVTID858:00: failed to find sensor: -5
ov13858 i2c-OVTID858:00: probe with driver ov13858 failed with error -5
The result is 32 /dev/video* nodes and a media graph with zero entities. The IPU7 itself is healthy - firmware loads, CSE authenticates, the device reaches secure mode - so the failure is entirely on the sensor-power side.
Reproduced on 6.17, 7.0.0-28 and 7.0.0-30 (Ubuntu 26.04), and the switch in drivers/platform/x86/intel/int3472/discrete.c still has no case for 0x08 in 7.1.0-rc7, so I do not believe this is already fixed.
What the firmware describes
---------------------------
The DSDT declares three INT3472 devices. Decoding their _DSM returns with the driver's own field layout (type = bits 7:0, pin = bits 15:8):
Device (ICL0) -> INT3472:00, the rear sensor (OVTID858 / ov13858)
0x1000070B type 0x0b POWER_ENABLE pin 7
0x10000500 type 0x00 RESET pin 5
0x1000060D type 0x0d PRIVACY_LED pin 6
0x10000408 type 0x08 <unknown> pin 4 <- refusedDevice (ICL1)
0x1000200B type 0x0b POWER_ENABLE pin 32
0x10000810 type 0x10 DOVDD pin 8
0x10000900 type 0x00 RESET pin 9
0x10000A0D type 0x0d PRIVACY_LED pin 10Device (ICL2)
0x1000170B type 0x0b POWER_ENABLE pin 23
0x10001600 type 0x00 RESET pin 22
0x1000250D type 0x0d PRIVACY_LED pin 37ICL0 is the only one of the three that declares a fourth GPIO, it is the only one carrying type 0x08, and it is the one whose sensor fails. I would not claim that proves causation - the driver returns 1 for the unknown type and carries on, so POWER_ENABLE, RESET and PRIVACY_LED are all still registered - but it is the only resource the kernel declines on this machine, and the sensor then does not answer on I2C.
The question
------------
What is type 0x08 meant to be, and should discrete.c handle it? If it is another regulator - the shape of ICL1's DOVDD entry suggests the encoding supports several - then adding it may be all this machine needs. If it is something else, I am happy to be told what and to test whatever you would like tried.
I have not sent a patch because I would only be guessing at the semantics, and guessing wrong here means silently powering a sensor rail for the wrong reason.
What I can provide
------------------
- full acpidump / disassembled DSDT for this machine
- any debug patch or instrumented build you would like run; the machine is available and I can rebuild and boot kernels on it
- dmesg at any log level
Two adjacent facts, in case they matter, though I am not asking for anything about them here: the front (SONY0681) and IR (SMO55F0) sensors have no in-tree driver bound at all, and intel_ipu7_isys still announces itself as a staging module.
Machine: Microsoft Surface Pro 11 for Business (Intel Core Ultra 7 268V) DMI SKU: Surface_Pro_11th_Edition_With_Intel_For_Business_2103
Firmware: UEFI 17.100.143 (2025-11-19)
Kernel: 7.0.0-30-generic, Ubuntu 26.04.1 LTS
Thanks,
Sergey Lebedev
Following up on my own report from this morning, because I should have found this first: the question I asked has already been answered in public, on a sibling machine, with patches.
https://github.com/linux-surface/linux-surface/issues/2153
djmulder worked out the Surface Pro 10 rear camera - the same OV13858 behind the same OVTID858 ACPI id - and identified GPIO type 0x08 as DVDD, a second digital power rail, mapped as con_id "dvdd2". They also found three causes my report did not mention at all, because I had not looked:
- drivers/media/pci/intel/ipu-bridge.c has no entry for OVTID858, so the IPU never recognises the sensor even once it is powered
- ov13858 never requests or releases the reset GPIO; the sensor is held in reset by the INT3472 and answers on I2C as soon as it is let go
- INT3472_MAX_SENSOR_GPIOS is 3, and the _DSM here declares four, so the
fourth would be refused by the array bound even with 0x08 understood
So please do not spend time re-deriving any of that on my account. My apologies for the noise; I searched the kernel history and MAINTAINERS before writing, but not the place where Surface owners actually work on Surface hardware, which is the obvious first place to look and is entirely my error.
What I think is still open, and what I can usefully do:
None of it has been confirmed on the Surface Pro 11, and the two machines are not identical. On SP10 the 0x08 GPIO sits at pin 0xC6; on this SP11 it is at pin 4, with the whole ICL0 descriptor set at different pins. The thread also notes the two models use different sensor clock rates.
I will apply those four patches here, report back whether they are sufficient on SP11 unchanged, and say plainly where they are not.
That thread describes its own CLK_IS_CRITICAL and always_on regulator constraints as too broad for upstream. If you would rather see a different shape tested - a DMI quirk, or teaching ov13858 to request its own regulators and clock - say which and I will try it here. The machine is available and I can build and boot kernels on it.
Thanks,
Sergey
Hans de Goede
maintainerHi,
Quoted 10 lines · Sergey Lebedev
Hello,
On a Microsoft Surface Pro 11 for Business (Intel, Lunar Lake) the rear camera does not work, and it traces to a single unhandled GPIO type in int3472-discrete.
int3472-discrete INT3472:00: GPIO type
0x08unknown;
the sensor may not work
ov13858 i2c-OVTID858:00: failed to find sensor: -5
ov13858 i2c-OVTID858:00: probe with driver ov13858 failed with error -5
There already is a patch which should fix this on the list:
https://lore.kernel.org/platform-driver-x86/[email protected]/
Regards,
Hans
Quoted 73 lines
The result is 32
/dev/video*nodes and a media graph with zero entities. The IPU7 itself is healthy - firmware loads, CSE authenticates, the device reaches secure mode - so the failure is entirely on the sensor-power side.Reproduced on 6.17, 7.0.0-28 and 7.0.0-30 (Ubuntu 26.04), and the switch in
drivers/platform/x86/intel/int3472/discrete.cstill has no case for0x08in 7.1.0-rc7, so I do not believe this is already fixed.What the firmware describes
---------------------------The DSDT declares three INT3472 devices. Decoding their
_DSMreturns with the driver's own field layout (type = bits 7:0, pin = bits 15:8):Device (ICL0) -> INT3472:00, the rear sensor (OVTID858 / ov13858) 0x1000070B type 0x0b POWER_ENABLE pin 7 0x10000500 type 0x00 RESET pin 5 0x1000060D type 0x0d PRIVACY_LED pin 6 0x10000408 type 0x08 <unknown> pin 4 <- refusedDevice (ICL1)
0x1000200B type 0x0b POWER_ENABLE pin 32 0x10000810 type 0x10 DOVDD pin 8 0x10000900 type 0x00 RESET pin 9 0x10000A0D type 0x0d PRIVACY_LED pin 10Device (ICL2)
0x1000170B type 0x0b POWER_ENABLE pin 23 0x10001600 type 0x00 RESET pin 22 0x1000250D type 0x0d PRIVACY_LED pin 37ICL0 is the only one of the three that declares a fourth GPIO, it is the only one carrying type
0x08, and it is the one whose sensor fails. I would not claim that proves causation - the driver returns 1 for the unknown type and carries on, soPOWER_ENABLE, RESET andPRIVACY_LEDare all still registered - but it is the only resource the kernel declines on this machine, and the sensor then does not answer on I2C.The question
------------What is type
0x08meant to be, and shoulddiscrete.chandle it? If it is another regulator - the shape of ICL1's DOVDD entry suggests the encoding supports several - then adding it may be all this machine needs. If it is something else, I am happy to be told what and to test whatever you would like tried.I have not sent a patch because I would only be guessing at the semantics, and guessing wrong here means silently powering a sensor rail for the wrong reason.
What I can provide
------------------- full acpidump / disassembled DSDT for this machine
- any debug patch or instrumented build you would like run; the machine is available and I can rebuild and boot kernels on it
- dmesg at any log levelTwo adjacent facts, in case they matter, though I am not asking for anything about them here: the front (SONY0681) and IR (SMO55F0) sensors have no in-tree driver bound at all, and
intel_ipu7_isysstill announces itself as a staging module.Machine: Microsoft Surface Pro 11 for Business (Intel Core Ultra 7 268V) DMI SKU:
Surface_Pro_11th_Edition_With_Intel_For_Business_2103
Firmware: UEFI 17.100.143 (2025-11-19)
Kernel: 7.0.0-30-generic, Ubuntu 26.04.1 LTSThanks,
Sergey Lebedev