Skip to contentSkip to conversation

dt-bindings: net: wireless: Convert WL1251 to DT schema

PATCH New Eduard Bostina 1 participant 1 message Sep 17

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 dt-bindings: net: wireless: Convert WL1251 to DT schema

Convert the Texas Instruments WL1251 Wireless LAN Controller bindings to DT schema.

During the conversion, the following updates were made:
- Added the 'clocks' property. It was missing from the txt binding but is used in device trees (omap3-n900.dts).
- Added 'spi-cpol' and 'spi-cpha'. These were present in the original txt binding's example but missing from its property list.
- 'vio-supply' and 'spi-max-frequency' are no longer required. The txt binding listed them as required, but they are only applicable when the chip is connected via SPI.

---
Changes in v3:
- Rename the example WLAN node from wl1251@0 to the generic node name wifi@0, as requested in review.

Link to v2: https://lore.kernel.org/all/[email protected]/
Link to v1: https://lore.kernel.org/all/[email protected]/

 .../bindings/net/wireless/ti,wl1251.txt       | 64 --------------
 .../bindings/net/wireless/ti,wl1251.yaml      | 85 +++++++++++++++++++
 2 files changed, 85 insertions(+), 64 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt
 create mode 100644 Documentation/devicetree/bindings/net/wireless/ti,wl1251.yaml
Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt deleted +0 -64
deleted file mode 100644
index 88fd28d15eac..000000000000
@@ -1,64 +0,0 @@
-* Texas Instruments wl1251 wireless lan controller
-
-The wl1251 chip can be connected via SPI or via SDIO. This
-document describes the binding for the SPI connected chip.
-
-Required properties:
-- compatible :        Should be "ti,wl1251"
-- reg :               Chip select address of device
-- spi-max-frequency : Maximum SPI clocking speed of device in Hz
-- interrupts :        Should contain interrupt line
-- vio-supply :        phandle to regulator providing VIO
-
-Optional properties:
-- ti,wl1251-has-eeprom : boolean, the wl1251 has an eeprom connected, which
-                         provides configuration data (calibration, MAC, ...)
-- ti,power-gpio :	 GPIO connected to chip's PMEN pin if operated in
-			 SPI mode
-- Please consult Documentation/devicetree/bindings/spi/spi-bus.txt
-  for optional SPI connection related properties,
-
-Examples:
-
-&spi1 {
-	wl1251@0 {
-		compatible = "ti,wl1251";
-
-		reg = <0>;
-		spi-max-frequency = <48000000>;
-		spi-cpol;
-		spi-cpha;
-
-		interrupt-parent = <&gpio2>;
-		interrupts = <10 IRQ_TYPE_NONE>; /* gpio line 42 */
-
-		vio-supply = <&vio>;
-		ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */
-	};
-};
-
-&mmc3 {
-	vmmc-supply = <&wlan_en>;
-
-	bus-width = <4>;
-	non-removable;
-	ti,non-removable;
-	cap-power-off-card;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc3_pins>;
-
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	wlan: wifi@1 {
-		compatible = "ti,wl1251";
-
-		reg = <1>;
-
-		interrupt-parent = <&gpio1>;
-		interrupts = <21 IRQ_TYPE_LEVEL_HIGH>;	/* GPIO_21 */
-
-		ti,wl1251-has-eeprom;
-	};
-};
Documentation/devicetree/bindings/net/wireless/ti,wl1251.yaml new file +85 -0

85 lines not on this page · raw message

Signature · 1 line
2.43.0