dmaengine: ste_dma40: Fix numerous accumulated bugs
Subsystems (2)
Linus Walleij
maintainerv5 cover dmaengine: ste_dma40: Fix numerous accumulated bugs
This series fixes 26 DMA40 bugs.
12 were found while reviewing the Ux500 LCLA SRAM power-domain conversion.
The cyclic transfer residue bug was exposed by Ux500 audio playback.
13 more issues were identified during review and hardware-manual audit.
The method taken is: whenever Sashiko complains: fix the bug it complains about if possible.
This has been boot tested on the Samsung Skomer device: DMA for MMC, wireless SDIO and UART still works after these patches, and DMA for audio started working.
---
Changes in v5:
- Simplify terminate-all runtime PM balancing by releasing its temporary reference in the successful resume path. Descriptor cleanup remains unconditional because it does not access DMA40 registers.
- Name and document the three-attempt cyclic-residue pointer sampling bound, and remove an unrelated whitespace-only change from that patch.
- Resynchronize cyclic callback tracking after failed hardware-pointer samples and limit unchanged-pointer interrupts to one callback. DMA40 has only one latched terminal-count bit, so extra periods coalesced while the pointer is unavailable and exact one-or-more full-buffer laps cannot be recovered without risking spurious callbacks.
- Count DMA40 status from channels owned by other SoC cores as handled without acknowledging it, so only status-less interrupts return IRQ_NONE and foreign DMA traffic cannot trigger spurious-IRQ disabling.
- Credit Frank Li for reporting the cyclic residue interrupt-counting issue.
- Link to v4: https://lore.kernel.org/r/[email protected]
Changes in v4:
- Rework cyclic-transfer residue reporting to use the current memory-side hardware pointer and reject periods that need more than one LLI.
- Add cyclic callback recovery when terminal-count interrupts coalesce.
- Retire all issued descriptors and release software channel state when a runtime PM resume fails, while avoiding inaccessible hardware registers.
- Validate physical event IDs against the variant event-group limit rather than the physical channel count, as confirmed by the DB8500 manual.
- Link to v3: https://lore.kernel.org/r/[email protected]
Changes in v3:
- Add a fix so physical channels advertise their existing cyclic support.
- Add a cyclic-transfer residue fix so DMAengine PCM reports the correct hardware pointer and Ux500 audio playback does not stop with -EIO.
- In patch 3, preserve cookie completion order when the next queued transfer fails to start and retire failed cyclic descriptors.
- In patch 4, enable runtime PM before requesting the IRQ so pending interrupts can be acknowledged during probe.
- In patch 5, keep valid interrupt handling with CONFIG_PM disabled and only drop a runtime PM reference when one was acquired.
- Add checked runtime PM resume handling to channel operations.
- Add an IRQ status patch returning IRQ_NONE when no DMA40 interrupt was acknowledged.
- In patch 8, keep the IRQ disabled until hardware initialization has configured and cleared the DMA40 interrupt state.
- In the DMA registration unwind patch, free the IRQ before unregistering the DMA devices and drain initialized tasklets before releasing storage.
- Add a fix releasing the LCPA SRAM node reference after reading it.
- Move the disabled-channels binding restoration to its own series.
- Store memcpy channel mappings per controller and check the property read.
- Add validation for disabled physical channel indexes.
- Reject DMA specifiers that do not contain exactly three cells.
- Reject transfer direction changes after channel allocation so logical channel resource masks are released correctly.
- In the event-group bounds patch, use variant-specific limits so DB8540 event group 4 remains available.
- Add fixed-channel fixes that search later physical blocks and validate configured physical channel indexes.
- Move the generic DMAengine debugfs naming fix to its own series.
- Use Assisted-by: LLM for the existing assistance trailers.
- Rebase onto v7.3-rc1.
- Link to v2: https://lore.kernel.org/r/[email protected]
Changes in v2:
- In patch 1, complete the failed-start descriptor through the normal tasklet path and drop the runtime PM reference instead of freeing the submitted descriptor directly.
- Add an IRQ fix to avoid register access when DMA40 is runtime suspended.
- Add a probe ordering fix so DMA40 hardware is initialized before DMAengine devices are registered.
- Add a probe unwind fix so DMAengine registrations are released before freeing IRQ and LCLA resources.
- Add an LCLA allocation fix so __get_free_pages() and free_pages() use an allocation order instead of a raw page count.
- Add a probe unwind fix so ESRAM LCLA mappings are not released with free_pages().
- Add a device tree parsing fix so memcpy-channels cannot overflow the memcpy channel array.
- Add a dev_type bounds fix so derived event groups cannot overflow
phy_res or the priority/realtime register window.
- Add validation for fallback memcpy configurations so memcpy-channels entries cannot bypass the dev_type bounds checks.
- Add a DMAengine debugfs naming fix so drivers registering several DMAengine devices for one parent device do not trigger duplicate-name warnings.
- Link to v1: https://lore.kernel.org/r/[email protected]
---
Linus Walleij (23):
dmaengine: ste_dma40: Fix physical cyclic capability
dmaengine: ste_dma40: Fix cyclic transfer residue
dmaengine: ste_dma40: Recover coalesced cyclic callbacks
dmaengine: ste_dma40: Fix failed start cleanup
dmaengine: ste_dma40: Fix probe runtime PM disable
dmaengine: ste_dma40: Check runtime PM in IRQ
dmaengine: ste_dma40: Handle runtime PM resume errors
dmaengine: ste_dma40: Return IRQ_NONE when no interrupt is pending
dmaengine: ste_dma40: Init hardware before registration
dmaengine: ste_dma40: Fix probe IRQ leak
dmaengine: ste_dma40: Fix DMA registration unwind
dmaengine: ste_dma40: Fix LCLA allocation order
dmaengine: ste_dma40: Fix probe LCLA free
dmaengine: ste_dma40: Put the LCPA SRAM node
dmaengine: ste_dma40: Fix memcpy channel parsing
dmaengine: ste_dma40: Validate disabled channel indexes
dmaengine: ste_dma40: Validate DMA specifier length
dmaengine: ste_dma40: Reject direction changes after allocation
dmaengine: ste_dma40: Fix logical channel bounds check
dmaengine: ste_dma40: Fix event group bounds
dmaengine: ste_dma40: Search all blocks for fixed logical channels
dmaengine: ste_dma40: Validate fixed physical channel indexes
dmaengine: ste_dma40: Validate memcpy configuration
drivers/dma/ste_dma40.c | 551 +++++++++++++++++++++++++++++++++++++----------- 1 file changed, 433 insertions(+), 118 deletions(-)
---
base-commit: cee9395acd8043be0644b25c34bfa86623f2b935
change-id: 20260820-dma40-fixes-b99af66002bf
Best regards,
Signature · 1 line
Linus Walleij <[email protected]>
Linus Walleij
maintainerPATCH v5 1/23 dmaengine: ste_dma40: Fix physical cyclic capability
d40_dmaengine_init() configures dma_both for physical channels that can handle both slave and memcpy transfers. Physical DMA40 channel setup has supported cyclic LLIs since cyclic transfer support was added, but the DMA_CYCLIC capability is set on dma_slave a second time instead of dma_both.
Set DMA_CYCLIC on dma_both so d40_ops_init() installs device_prep_dma_cyclic and physical channels advertise cyclic support.
--- drivers/dma/ste_dma40.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/dma/ste_dma40.c +1 -1
@@ -2897,7 +2897,7 @@ static int __init d40_dmaengine_init(struct d40_base *base,dma_cap_zero (base->dma_both.cap_mask);dma_cap_set (DMA_SLAVE , base->dma_both.cap_mask);dma_cap_set (DMA_MEMCPY , base->dma_both.cap_mask); -dma_cap_set (DMA_CYCLIC , base->dma_slave.cap_mask); +dma_cap_set (DMA_CYCLIC , base->dma_both.cap_mask);d40_ops_init (base, &base->dma_both); err =dmaenginem_async_device_register (&base->dma_both);
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 2/23 dmaengine: ste_dma40: Fix cyclic transfer residue
In reply to Linus WalleijDMA40 reads residue from the element count of the currently active LLI. For a cyclic transfer this reports at most one period, not the bytes remaining until the cyclic buffer wraps.
Once DMA40 advertises burst granularity, DMAengine PCM uses this residue directly. For a four-period PCM buffer it consequently reports the hardware pointer near three periods after every period interrupt. ALSA eventually stops playback with -EIO although DMA period callbacks continue.
Calculate cyclic residue from the current memory-side hardware pointer instead. Read the destination pointer for capture and the source pointer for playback. Sample the split logical channel pointer coherently and retain the last valid residue during relink transitions.
Make at most three residue sampling attempts: one initial read plus two retries. The retries let transient split-register updates or LLI relink windows settle, while the limit prevents unbounded polling if hardware does not yield a valid pointer.
This avoids counting terminal-count interrupts, which races with hardware advancing to the next LLI and cannot account for coalesced interrupt status. Also reject cyclic periods that expand into multiple LLIs because logical cyclic LLIs each request a terminal-count interrupt and would generate more than one callback per period.
Reject invalid cyclic geometries before dividing or constructing the scatterlist as well.
--- drivers/dma/ste_dma40.c | 106 +++++++++++++++++++++++++++++++++++++++++++++--- 1 file changed, 101 insertions(+), 5 deletions(-)
drivers/dma/ste_dma40.c +101 -5
@@ -65,6 +65,9 @@ struct stedma40_platform_data {/* Maximum iterations taken before giving up suspending a channel */ #define D40_SUSPEND_MAX_IT 500 +/* Maximum attempts to sample a stable cyclic residue position */ +#define D40_RESIDUE_MAX_ATTEMPTS 3 +/* Milliseconds */ #define DMA40_AUTOSUSPEND_DELAY 100
@@ -378,6 +381,9 @@ struct d40_lli_pool {* @lli_len: Number of llis of current descriptor. * @lli_current: Number of transferred llis. * @lcla_alloc: Number of LCLA entries allocated. +* @cyclic_dma_addr: Start address of the cyclic buffer. +* @cyclic_buf_len: Length of the cyclic buffer. +* @cyclic_residue: Last valid cyclic residue sample. * @txd: DMA engine struct. Used for among other things for communication * during a transfer. * @node: List entry.
@@ -396,6 +402,9 @@ struct d40_desc {int lli_len;int lli_current;int lcla_alloc; +dma_addr_t cyclic_dma_addr; +size_t cyclic_buf_len; +size_t cyclic_residue;struct dma_async_tx_descriptor txd;struct list_head node;
@@ -1420,6 +1429,64 @@ static u32 d40_residue(struct d40_chan *d40c)return num_elt * d40c->dma_cfg.dst_info.data_width; } +static bool d40_current_addr (struct d40_chan *d40c,dma_addr_t *addr) +{ +bool dst = d40c->dma_cfg.dir ==DMA_DEV_TO_MEM ; +void __iomem *high_reg; +void __iomem *low_reg; +u32 low; +u32 high; +u32 check; +int i; + +if (chan_is_physical (d40c)) { + *addr =readl (chan_base (d40c) + + (dst ?D40_CHAN_REG_SDPTR :D40_CHAN_REG_SSPTR )); +return true; + } + +if (dst) { + low_reg = &d40c->lcpa->lcsp2; + high_reg = &d40c->lcpa->lcsp3; + }else { + low_reg = &d40c->lcpa->lcsp0; + high_reg = &d40c->lcpa->lcsp1; + } + +for (i =0 ; i <D40_RESIDUE_MAX_ATTEMPTS ; i++) { + high =readl (high_reg) &D40_MEM_LCSP1_SPTR_MASK ; + low =readl (low_reg) &D40_MEM_LCSP0_SPTR_MASK ; + check =readl (high_reg) &D40_MEM_LCSP1_SPTR_MASK ; +if (high == check) { + *addr = low | high; +return true; + } + } + +return false; +} + +static bool d40_cyclic_offset (struct d40_chan *d40c,struct d40_desc *d40d, +size_t *offset) +{ +dma_addr_t current_addr; +dma_addr_t current_offset; +int i; + +for (i =0 ; i <D40_RESIDUE_MAX_ATTEMPTS ; i++) { +if (!d40_current_addr (d40c, ¤t_addr)) +continue ; + + current_offset = current_addr - d40d->cyclic_dma_addr; +if (current_offset <= d40d->cyclic_buf_len) { + *offset = current_offset; +return true; + } + } + +return false; +} +static bool d40_tx_is_linked (struct d40_chan *d40c) {bool is_link;
@@ -2108,15 +2175,26 @@ static bool d40_is_paused(struct d40_chan *d40c) } -static u32 stedma40_residue (struct dma_chan *chan) +static u32 stedma40_residue (struct dma_chan *chan,dma_cookie_t cookie) {struct d40_chan *d40c = container_of(chan, struct d40_chan, chan); +struct d40_desc *d40d; +size_t offset;u32 bytes_left;unsigned long flags;spin_lock_irqsave (&d40c->lock, flags); - bytes_left =d40_residue (d40c); + d40d =d40_first_active_get (d40c); +if (d40d && d40d->txd.cookie == cookie && d40d->cyclic && + d40d->cyclic_buf_len) { +if (d40_cyclic_offset (d40c, d40d, &offset)) + d40d->cyclic_residue = d40d->cyclic_buf_len - offset; + bytes_left = d40d->cyclic_residue; + }else { + bytes_left =d40_residue (d40c); + } +spin_unlock_irqrestore (&d40c->lock, flags);return bytes_left;
@@ -2246,8 +2324,13 @@ d40_prep_sg(struct dma_chan *dchan, struct scatterlist *sg_src,if (desc ==NULL ) goto unlock; -if (sg_next (&sg_src[sg_len -1 ]) == sg_src) +if (sg_next (&sg_src[sg_len -1 ]) == sg_src) { desc->cyclic = true; +if (desc->lli_len != sg_len) { +chan_err (chan,"Cyclic periods must fit in one LLI\n" ); + goto free_desc; + } + } src_dev_addr =0 ; dst_dev_addr =0 ;
@@ -2524,11 +2607,18 @@ dma40_prep_dma_cyclic(struct dma_chan *chan, dma_addr_t dma_addr, size_t buf_len, size_t period_len, enum dma_transfer_direction direction, unsigned long flags) { - unsigned int periods = buf_len / period_len; + unsigned int periods;struct dma_async_tx_descriptor *txd; +struct d40_desc *desc;struct scatterlist *sg; +dma_addr_t buf_addr = dma_addr;int i; +if (!buf_len || !period_len || buf_len % period_len) +return NULL ; + + periods = buf_len / period_len; + sg = kzalloc_objs(struct scatterlist, periods + 1, GFP_NOWAIT);if (!sg)return NULL ;
@@ -2543,6 +2633,12 @@ dma40_prep_dma_cyclic(struct dma_chan *chan, dma_addr_t dma_addr, txd =d40_prep_sg (chan, sg, sg, periods, direction,DMA_PREP_INTERRUPT ); +if (txd) { + desc = container_of(txd, struct d40_desc, txd); + desc->cyclic_dma_addr = buf_addr; + desc->cyclic_buf_len = buf_len; + desc->cyclic_residue = buf_len; + }kfree (sg);
@@ -2563,7 +2659,7 @@ static enum dma_status d40_tx_status(struct dma_chan *chan, ret =dma_cookie_status (chan, cookie, txstate);if (ret !=DMA_COMPLETE && txstate) -dma_set_residue (txstate,stedma40_residue (chan)); +dma_set_residue (txstate,stedma40_residue (chan, cookie));if (d40_is_paused (d40c)) ret =DMA_PAUSED ;
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 3/23 dmaengine: ste_dma40: Recover coalesced cyclic callbacks
In reply to Linus WalleijDMA40 has one terminal-count status bit per channel, so cyclic period interrupts can coalesce.
Use the memory-side pointer displacement to queue the minimum observable number of callbacks. If sampling fails, queue one callback and invalidate the saved position; the next successful sample resynchronizes without recounting it.
The pointer is modulo the cyclic buffer: a displacement of d periods can mean d plus n complete iterations of the buffer. Report d, so the driver could have missed n iterations of the buffer; DMA40 has no counter to recover them. For an unchanged pointer, report one callback rather than risk a spurious full-buffer burst.
This condition has not been seen in practice and is only a product of review comments that the buffer can miss interrupts.
The preceding cyclic-residue fix ensures that every cyclic period fits in one LLI, so each boundary corresponds to one client callback.
--- drivers/dma/ste_dma40.c | 72 ++++++++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 71 insertions(+), 1 deletion(-)
drivers/dma/ste_dma40.c +71 -1
@@ -384,11 +384,14 @@ struct d40_lli_pool {* @cyclic_dma_addr: Start address of the cyclic buffer. * @cyclic_buf_len: Length of the cyclic buffer. * @cyclic_residue: Last valid cyclic residue sample. +* @cyclic_period_len: Length of one cyclic period. +* @cyclic_callback_pos: Position after the callbacks already queued. * @txd: DMA engine struct. Used for among other things for communication * during a transfer. * @node: List entry. * @is_in_client_list: true if the client owns this descriptor. * @cyclic: true if this is a cyclic job +* @cyclic_callback_pos_valid: Whether cyclic_callback_pos is reliable. * * This descriptor is used for both logical and physical transfers. */
@@ -405,12 +408,15 @@ struct d40_desc {dma_addr_t cyclic_dma_addr;size_t cyclic_buf_len;size_t cyclic_residue; +size_t cyclic_period_len; +size_t cyclic_callback_pos;struct dma_async_tx_descriptor txd;struct list_head node;bool is_in_client_list;bool cyclic; +bool cyclic_callback_pos_valid; };/**
@@ -1487,6 +1493,64 @@ static bool d40_cyclic_offset(struct d40_chan *d40c, struct d40_desc *d40d,return false; } +static unsigned int d40_cyclic_periods_elapsed (struct d40_chan *d40c, +struct d40_desc *d40d) +{ +size_t current_pos; +size_t offset; +unsigned int periods; + +if (!d40d->cyclic_period_len) +return 1 ; + +if (!d40_cyclic_offset (d40c, d40d, &offset)) { + d40d->cyclic_callback_pos_valid = false; +return 1 ; + } + + current_pos =rounddown (offset, d40d->cyclic_period_len); +if (!d40_residue (d40c) && current_pos != offset) + current_pos += d40d->cyclic_period_len; +if (current_pos == d40d->cyclic_buf_len) + current_pos =0 ; + +if (!d40d->cyclic_callback_pos_valid) { +/* +* The previous interrupt was reported without a pointer +* sample. Resynchronize without using the stale position, +* which would count that callback again. +*/ + d40d->cyclic_callback_pos = current_pos; + d40d->cyclic_callback_pos_valid = true; +return 1 ; + } + +/* +* The pointer wraps with the cyclic buffer, so its displacement is +* only the minimum number of elapsed periods. Complete buffer laps +* are not observable. +*/ +if (current_pos > d40d->cyclic_callback_pos) { + periods = (current_pos - d40d->cyclic_callback_pos) / + d40d->cyclic_period_len; + }else if (current_pos < d40d->cyclic_callback_pos) { + periods = (d40d->cyclic_buf_len - + d40d->cyclic_callback_pos + current_pos) / + d40d->cyclic_period_len; + }else { +/* +* The TC status is a single latched bit. An unchanged pointer +* cannot distinguish a complete lap from a repeated interrupt, +* so do not amplify it into a buffer's worth of callbacks. +*/ + periods =1 ; + } + + d40d->cyclic_callback_pos = current_pos; + +return periods; +} +static bool d40_tx_is_linked (struct d40_chan *d40c) {bool is_link;
@@ -1609,6 +1673,7 @@ static struct d40_desc *d40_queue_start(struct d40_chan *d40c)static void dma_tc_handle (struct d40_chan *d40c) {struct d40_desc *d40d; +unsigned int callbacks =1 ;/* Get first active entry from list */ d40d =d40_first_active_get (d40c);
@@ -1633,6 +1698,8 @@ static void dma_tc_handle(struct d40_chan *d40c)if (d40d->lli_current == d40d->lli_len) d40d->lli_current =0 ; } + + callbacks =d40_cyclic_periods_elapsed (d40c, d40d); }else {d40_lcla_free_all (d40c, d40d);
@@ -1653,7 +1720,7 @@ static void dma_tc_handle(struct d40_chan *d40c)d40_desc_done (d40c, d40d); } - d40c->pending_tx++; + d40c->pending_tx += callbacks;tasklet_schedule (&d40c->tasklet); }
@@ -2638,6 +2705,9 @@ dma40_prep_dma_cyclic(struct dma_chan *chan, dma_addr_t dma_addr, desc->cyclic_dma_addr = buf_addr; desc->cyclic_buf_len = buf_len; desc->cyclic_residue = buf_len; + desc->cyclic_period_len = period_len; + desc->cyclic_callback_pos =0 ; + desc->cyclic_callback_pos_valid = true; }kfree (sg);
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 4/23 dmaengine: ste_dma40: Fix failed start cleanup
In reply to Linus WalleijIf d40_start() fails after a queued descriptor has been moved to the active list, d40_queue_start() currently returns NULL without unwinding the transfer state or clearing the channel busy flag.
Fix this pre-existing error path by completing the descriptor through the normal tasklet path, clearing the busy flag, balancing the runtime PM reference and returning an error pointer to distinguish the failure from the no-work case. Do not free the descriptor directly, since it has already been submitted and has a DMA cookie.
When starting the next queued transfer from the completion handler, put the completed descriptor on the done list first. This preserves FIFO completion order if the new transfer fails to start and prevents the completed cookie from moving backwards.
Use done-list membership rather than the cyclic flag to identify terminal descriptors in the tasklet. A cyclic descriptor that failed to start is then completed and removed instead of remaining permanently at the head of the done list.
--- drivers/dma/ste_dma40.c | 25 +++++++++++++++++-------- 1 file changed, 17 insertions(+), 8 deletions(-)
drivers/dma/ste_dma40.c +17 -8
@@ -1662,8 +1662,15 @@ static struct d40_desc *d40_queue_start(struct d40_chan *d40c)/* Start dma job */ err =d40_start (d40c); -if (err) -return NULL ; +if (err) { +d40_desc_remove (d40d); +d40_desc_done (d40c, d40d); + d40c->pending_tx++; + d40c->busy = false; +pm_runtime_put_autosuspend (d40c->base->dev); +tasklet_schedule (&d40c->tasklet); +return ERR_PTR (err); + } }return d40d;
@@ -1710,14 +1717,14 @@ static void dma_tc_handle(struct d40_chan *d40c)return ; } +d40_desc_remove (d40d); +d40_desc_done (d40c, d40d); +if (d40_queue_start (d40c) ==NULL ) { d40c->busy = false;pm_runtime_put_autosuspend (d40c->base->dev); } - -d40_desc_remove (d40d); -d40_desc_done (d40c, d40d); } d40c->pending_tx += callbacks;
@@ -1731,20 +1738,22 @@ static void dma_tasklet(struct tasklet_struct *t)struct d40_desc *d40d;unsigned long flags;bool callback_active; +bool from_done;struct dmaengine_desc_callback cb;spin_lock_irqsave (&d40c->lock, flags);/* Get first entry from the done list */ d40d =d40_first_done (d40c); -if (d40d ==NULL ) { + from_done = !!d40d; +if (!from_done) {/* Check if we have reached here for cyclic job */ d40d =d40_first_active_get (d40c);if (d40d ==NULL || !d40d->cyclic) goto check_pending_tx; } -if (!d40d->cyclic) +if (from_done)dma_cookie_complete (&d40d->txd);/*
@@ -1760,7 +1769,7 @@ static void dma_tasklet(struct tasklet_struct *t) callback_active = !!(d40d->txd.flags &DMA_PREP_INTERRUPT );dmaengine_desc_get_callback (&d40d->txd, &cb); -if (!d40d->cyclic) { +if (from_done) {if (async_tx_test_ack (&d40d->txd)) {d40_desc_remove (d40d);d40_desc_free (d40c, d40d);
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 5/23 dmaengine: ste_dma40: Fix probe runtime PM disable
In reply to Linus WalleijSome d40_probe() error paths jump to destroy_cache before runtime PM has been enabled for the DMA controller device. The label unconditionally calls pm_runtime_disable(), which increments disable_depth even though this probe attempt never enabled runtime PM.
Track whether this probe attempt enabled runtime PM before disabling it on the error path. This is not about a later deferred-probe retry, since the driver is registered with platform_driver_probe(); it keeps the probe unwind balanced.
The interrupt handler uses pm_runtime_get_if_active() and cannot acknowledge a pending interrupt while runtime PM is disabled. Request the IRQ only after enabling runtime PM so the handler cannot enter an unacknowledged interrupt loop during probe.
--- drivers/dma/ste_dma40.c | 17 ++++++++++------- 1 file changed, 10 insertions(+), 7 deletions(-)
drivers/dma/ste_dma40.c +10 -7
@@ -3673,6 +3673,7 @@ static int __init d40_probe(struct platform_device *pdev)struct resource *res;struct resource res_lcpa;int num_reserved_chans; +bool runtime_pm_enabled = false;u32 val;int ret;
@@ -3760,12 +3761,6 @@ static int __init d40_probe(struct platform_device *pdev) goto destroy_cache; } - ret =request_irq (base->irq, d40_handle_interrupt,0 ,D40_NAME , base); -if (ret) { -d40_err (dev,"No IRQ defined\n" ); - goto destroy_cache; - } -if (base->plat_data->use_esram_lcla) { base->lcpa_regulator =regulator_get (base->dev,"lcla_esram" );
@@ -3794,6 +3789,13 @@ static int __init d40_probe(struct platform_device *pdev)pm_runtime_mark_last_busy (base->dev);pm_runtime_set_active (base->dev);pm_runtime_enable (base->dev); + runtime_pm_enabled = true; + + ret =request_irq (base->irq, d40_handle_interrupt,0 ,D40_NAME , base); +if (ret) { +d40_err (dev,"No IRQ defined\n" ); + goto destroy_cache; + } ret =d40_dmaengine_init (base, num_reserved_chans);if (ret)
@@ -3829,7 +3831,8 @@ static int __init d40_probe(struct platform_device *pdev)regulator_disable (base->lcpa_regulator);regulator_put (base->lcpa_regulator); } -pm_runtime_disable (base->dev); +if (runtime_pm_enabled) +pm_runtime_disable (base->dev); report_failure:d40_err (dev,"probe failed\n" );
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 6/23 dmaengine: ste_dma40: Check runtime PM in IRQ
In reply to Linus Walleijd40_handle_interrupt() reads DMA40 interrupt registers unconditionally. A spurious interrupt can arrive while the device is runtime suspended, after dma40_runtime_suspend() has disabled the GCC clock.
Avoid touching the registers unless the device is runtime active by taking a conditional runtime PM reference. Return IRQ_NONE when the device is suspended, and drop the reference after handling an active interrupt.
When CONFIG_PM is disabled, pm_runtime_get_if_active() returns -EINVAL even though the registers remain accessible. Keep handling interrupts in that configuration and only drop the runtime PM reference when one was acquired.
--- drivers/dma/ste_dma40.c | 8 ++++++++ 1 file changed, 8 insertions(+)
drivers/dma/ste_dma40.c +8 -0
@@ -1810,6 +1810,11 @@ static irqreturn_t d40_handle_interrupt(int irq, void *data)u32 *regs = base->regs_interrupt;struct d40_interrupt_lookup *il = base->gen_dmac.il;u32 il_size = base->gen_dmac.il_size; +int ret; + + ret =pm_runtime_get_if_active (base->dev); +if (IS_ENABLED (CONFIG_PM ) && ret <=0 ) +return IRQ_NONE ;spin_lock (&base->interrupt_lock);
@@ -1858,6 +1863,9 @@ static irqreturn_t d40_handle_interrupt(int irq, void *data)spin_unlock (&base->interrupt_lock); +if (ret >0 ) +pm_runtime_put_autosuspend (base->dev); +return IRQ_HANDLED ; }
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 7/23 dmaengine: ste_dma40: Handle runtime PM resume errors
In reply to Linus WalleijSeveral channel operations use pm_runtime_get_sync() and access DMA40 registers without checking whether runtime resume succeeded. If resume fails, the registers may be inaccessible. pm_runtime_get_sync() also increments the usage counter on failure, making error unwinding easy to unbalance.
Use pm_runtime_resume_and_get() and avoid register access when resume fails. Acquire the runtime PM reference before allocating a channel so failure needs no channel-allocation rollback.
If a queued transfer cannot be started because resume failed, retire all issued descriptors through the normal tasklet path. Since dma_async_issue_pending() cannot return an error, leaving them queued would make clients wait indefinitely for callbacks.
Termination and channel release must also clean up software state when the controller cannot resume. Always release descriptors and the outstanding busy reference, and release channel allocation state when freeing the channel. Skip only the hardware stop that requires register access.
--- drivers/dma/ste_dma40.c | 69 +++++++++++++++++++++++++++++++++++++------------ 1 file changed, 52 insertions(+), 17 deletions(-)
drivers/dma/ste_dma40.c +52 -17
@@ -1579,11 +1579,14 @@ static int d40_pause(struct dma_chan *chan)return 0 ;spin_lock_irqsave (&d40c->lock, flags); -pm_runtime_get_sync (d40c->base->dev); + res =pm_runtime_resume_and_get (d40c->base->dev); +if (res <0 ) + goto unlock; res =d40_channel_execute_command (d40c,D40_DMA_SUSPEND_REQ );pm_runtime_put_autosuspend (d40c->base->dev); + unlock:spin_unlock_irqrestore (&d40c->lock, flags);return res; }
@@ -1603,13 +1606,16 @@ static int d40_resume(struct dma_chan *chan)return 0 ;spin_lock_irqsave (&d40c->lock, flags); -pm_runtime_get_sync (d40c->base->dev); + res =pm_runtime_resume_and_get (d40c->base->dev); +if (res <0 ) + goto unlock;/* If bytes left to transfer or linked tx resume job */ if (d40_residue (d40c) ||d40_tx_is_linked (d40c)) res =d40_channel_execute_command (d40c,D40_DMA_RUN );pm_runtime_put_autosuspend (d40c->base->dev); + unlock:spin_unlock_irqrestore (&d40c->lock, flags);return res; }
@@ -1646,8 +1652,20 @@ static struct d40_desc *d40_queue_start(struct d40_chan *d40c)if (d40d !=NULL ) {if (!d40c->busy) { + err =pm_runtime_resume_and_get (d40c->base->dev); +if (err <0 ) { +chan_err (d40c,"Failed to resume DMA: %d\n" , + err); +do { +d40_desc_remove (d40d); +d40_desc_done (d40c, d40d); + d40c->pending_tx++; + d40d =d40_first_queued (d40c); + }while (d40d); +tasklet_schedule (&d40c->tasklet); +return ERR_PTR (err); + } d40c->busy = true; -pm_runtime_get_sync (d40c->base->dev); }/* Remove from queue */
@@ -2162,11 +2180,9 @@ static int d40_free_dma(struct d40_chan *d40c)int res =0 ;u32 event =D40_TYPE_TO_EVENT (d40c->dma_cfg.dev_type);struct d40_phy_res *phy = d40c->phy_chan; +bool pm_acquired = false;bool is_src; -/* Terminate all queued and active transfers */ -d40_term_all (d40c); -if (phy ==NULL ) {chan_err (d40c,"phy == null\n" );return -EINVAL ;
@@ -2188,13 +2204,21 @@ static int d40_free_dma(struct d40_chan *d40c)return -EINVAL ; } -pm_runtime_get_sync (d40c->base->dev); +/* Terminate all queued and active transfers */ +d40_term_all (d40c); + + res =pm_runtime_resume_and_get (d40c->base->dev); +if (res <0 ) + goto release_channel; + pm_acquired = true; + res =d40_channel_execute_command (d40c,D40_DMA_STOP );if (res) {chan_err (d40c,"stop failed\n" ); goto mark_last_busy; } + release_channel:d40_alloc_mask_free (phy, is_src,chan_is_logical (d40c) ? event :0 );if (chan_is_logical (d40c))
@@ -2209,7 +2233,8 @@ static int d40_free_dma(struct d40_chan *d40c) d40c->phy_chan =NULL ; d40c->configured = false; mark_last_busy: -pm_runtime_put_autosuspend (d40c->base->dev); +if (pm_acquired) +pm_runtime_put_autosuspend (d40c->base->dev);return res; }
@@ -2584,10 +2609,14 @@ static int d40_alloc_chan_resources(struct dma_chan *chan) err =d40_config_memcpy (d40c);if (err) {chan_err (d40c,"Failed to configure memcpy channel\n" ); - goto mark_last_busy; + goto unlock; } } + err =pm_runtime_resume_and_get (d40c->base->dev); +if (err <0 ) + goto unlock; + err =d40_allocate_channel (d40c, &is_free_phy);if (err) {chan_err (d40c,"Failed to allocate channel\n" );
@@ -2595,8 +2624,6 @@ static int d40_alloc_chan_resources(struct dma_chan *chan) goto mark_last_busy; } -pm_runtime_get_sync (d40c->base->dev); -d40_set_prio_realtime (d40c);if (chan_is_logical (d40c)) {
@@ -2628,6 +2655,7 @@ static int d40_alloc_chan_resources(struct dma_chan *chan)d40_config_write (d40c); mark_last_busy:pm_runtime_put_autosuspend (d40c->base->dev); + unlock:spin_unlock_irqrestore (&d40c->lock, flags);return err; }
@@ -2788,19 +2816,26 @@ static int d40_terminate_all(struct dma_chan *chan)spin_lock_irqsave (&d40c->lock, flags); -pm_runtime_get_sync (d40c->base->dev); - ret =d40_channel_execute_command (d40c,D40_DMA_STOP ); -if (ret) -chan_err (d40c,"Failed to stop channel\n" ); + ret =pm_runtime_resume_and_get (d40c->base->dev); +if (ret >=0 ) { + ret =d40_channel_execute_command (d40c,D40_DMA_STOP ); +if (ret) +chan_err (d40c,"Failed to stop channel\n" ); + +pm_runtime_put_autosuspend (d40c->base->dev); + } +/* +* Always release software state, even when the controller cannot +* resume. d40_term_all() does not access DMA40 registers. +*/ d40_term_all (d40c); -pm_runtime_put_autosuspend (d40c->base->dev);if (d40c->busy)pm_runtime_put_autosuspend (d40c->base->dev); d40c->busy = false;spin_unlock_irqrestore (&d40c->lock, flags); -return 0 ; +return ret; } static int
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 8/23 dmaengine: ste_dma40: Return IRQ_NONE when no interrupt is pending
In reply to Linus Walleijd40_handle_interrupt() returns IRQ_HANDLED even when no terminal-count or error status bit is pending.
IRQ_NONE is not only used to identify a device on a shared interrupt. The generic IRQ core also counts it as unhandled for spurious IRQ detection. DMA40 does not request this IRQ with IRQF_SHARED, so interrupt sharing is not the purpose of this change.
If the line remains asserted without matching DMA40 status, returning IRQ_HANDLED hides the stuck interrupt and can leave the CPU servicing it indefinitely. Track whether any DMA40 status is pending and return IRQ_NONE when none is present, allowing the generic IRQ core to diagnose and eventually disable the faulty line.
DMA40 channels can be owned by other SoC cores. Their status means that the interrupt is real, but Linux must not acknowledge it. Treat foreign status as handled and leave its acknowledgment to the owning core, while acknowledging and dispatching only registered Linux channels.
--- drivers/dma/ste_dma40.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)
drivers/dma/ste_dma40.c +8 -1
@@ -1819,6 +1819,7 @@ static void dma_tasklet(struct tasklet_struct *t)static irqreturn_t d40_handle_interrupt (int irq,void *data) { +irqreturn_t handled =IRQ_NONE ;int i;u32 idx;u32 row;
@@ -1852,6 +1853,12 @@ static irqreturn_t d40_handle_interrupt(int irq, void *data) row = chan /BITS_PER_LONG ; idx = chan & (BITS_PER_LONG -1 ); +/* +* Status for a channel owned by another core still explains +* the interrupt, but only ACK Linux-owned channels below. +*/ + handled =IRQ_HANDLED ; +if (il[row].offset ==D40_PHY_CHAN ) d40c = base->lookup_phy_chans[idx];else
@@ -1884,7 +1891,7 @@ static irqreturn_t d40_handle_interrupt(int irq, void *data)if (ret >0 )pm_runtime_put_autosuspend (base->dev); -return IRQ_HANDLED ; +return handled; } static int d40_validate_conf(struct d40_chan *d40c,
Signature · 1 line
2.55.0
[email protected]
AI reviewRe: [PATCH v5 08/23] dmaengine: ste_dma40: Return IRQ_NONE when no interrupt is pending
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider: - [High] dmaengine: ste_dma40: spurious IRQ regression due to returning IRQ_NONE --
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [High] dmaengine: ste_dma40: spurious IRQ regression due to returning IRQ_NONE --
commit b3869fd527499e9a4f208caed7dc53effe8c70c3
Author: Linus Walleij <[email protected]>
dmaengine: ste_dma40: Return IRQ_NONE when no interrupt is pending
The commit modifies d40_handle_interrupt() to return IRQ_NONE when no status bits are pending. This is intended to allow the generic IRQ core to diagnose stuck interrupts and eventually disable the line.
Quoted 12 lines
drivers/dma/ste_dma40.c +1
-0@@ -1819,6 +1819,7 @@ static void dma_tasklet(struct tasklet_struct *t)static irqreturn_t d40_handle_interrupt (int irq,void *data) { +irqreturn_t handled =IRQ_NONE ;int i;u32 idx;u32 row;
[ ... ]
drivers/dma/ste_dma40.c static irqreturn_t d40_handle_interrupt(int irq, void *data) · line 1894
Quoted 6 lines
drivers/dma/ste_dma40.c +1
-1@@ -1884,7 +1891,7 @@ static irqreturn_t d40_handle_interrupt(int irq, void *data)if (ret >0 )pm_runtime_put_autosuspend (base->dev); -return IRQ_HANDLED ; +return handled;
[Severity: High]
Could returning IRQ_NONE when 0 status bits are found cause the generic IRQ subsystem to permanently disable the DMA40 interrupt line ('irq xx: nobody cared')?
As noted in the commit message, the hardware interrupt is shared with other SoC cores. When a foreign core's DMA channel asserts the interrupt, both cores may wake up. If the foreign core clears its status register before Linux's d40_handle_interrupt() executes its readl(), Linux will read 0 status bits.
Also, when Linux clears an interrupt via writel() earlier in this handler, the posted write may be delayed over the bus because there is no flushing readl(). The CPU might exit the handler and re-enable interrupts before the write reaches the hardware, causing an immediate spurious re-entry where Linux again reads 0 status bits.
Will these transient delays now be counted as unhandled interrupts, eventually breaking the DMA controller and dependent peripherals once 100,000 unhandled interrupts accumulate?
Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=8
Linus Walleij
maintainerPATCH v5 9/23 dmaengine: ste_dma40: Init hardware before registration
In reply to Linus Walleijd40_probe() enables the interrupt handler and registers DMAengine devices before calling d40_hw_init(). An interrupt pending from the bootloader can therefore reach the handler while the hardware interrupt state is not initialized and channel lookup entries are empty. The handler deliberately does not acknowledge an interrupt for an unknown channel, so a level IRQ can retrigger continuously.
Request the IRQ with IRQF_NO_AUTOEN, then initialize the hardware and set the DMA segment limit. Enable the IRQ before registering DMAengine devices. This ensures the handler and clients only observe initialized hardware while still letting request_irq() fail before hardware interrupts are enabled.
--- drivers/dma/ste_dma40.c | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-)
drivers/dma/ste_dma40.c +7 -5
@@ -3841,19 +3841,21 @@ static int __init d40_probe(struct platform_device *pdev)pm_runtime_enable (base->dev); runtime_pm_enabled = true; - ret =request_irq (base->irq, d40_handle_interrupt,0 ,D40_NAME , base); + ret =request_irq (base->irq, d40_handle_interrupt,IRQF_NO_AUTOEN , +D40_NAME , base);if (ret) {d40_err (dev,"No IRQ defined\n" ); goto destroy_cache; } - ret =d40_dmaengine_init (base, num_reserved_chans); -if (ret) - goto destroy_cache; -dma_set_max_seg_size (base->dev,STEDMA40_MAX_SEG_SIZE );d40_hw_init (base); +enable_irq (base->irq); + + ret =d40_dmaengine_init (base, num_reserved_chans); +if (ret) + goto destroy_cache; ret =of_dma_controller_register (np, d40_xlate,NULL );if (ret) {
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 10/23 dmaengine: ste_dma40: Fix probe IRQ leak
In reply to Linus Walleijd40_probe() registers the hardware interrupt before several later probe steps that can fail. Those error paths jump to destroy_cache without freeing the IRQ, leaving the handler registered after probe resources have been released.
Track successful IRQ registration and free the IRQ on later probe failure.
--- drivers/dma/ste_dma40.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/dma/ste_dma40.c +4 -0
@@ -3724,6 +3724,7 @@ static int __init d40_probe(struct platform_device *pdev)struct resource res_lcpa;int num_reserved_chans;bool runtime_pm_enabled = false; +bool irq_requested = false;u32 val;int ret;
@@ -3847,6 +3848,7 @@ static int __init d40_probe(struct platform_device *pdev)d40_err (dev,"No IRQ defined\n" ); goto destroy_cache; } + irq_requested = true;dma_set_max_seg_size (base->dev,STEDMA40_MAX_SEG_SIZE );
@@ -3883,6 +3885,8 @@ static int __init d40_probe(struct platform_device *pdev)regulator_disable (base->lcpa_regulator);regulator_put (base->lcpa_regulator); } +if (irq_requested) +free_irq (base->irq, base);if (runtime_pm_enabled)pm_runtime_disable (base->dev);
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 11/23 dmaengine: ste_dma40: Fix DMA registration unwind
In reply to Linus Walleijd40_dmaengine_init() registers DMAengine devices using devres-managed unregister actions. If probe fails after one of those registrations, the DMAengine devices stay visible until devres unwinds after d40_probe() returns.
The channel tasklets are also initialized before each DMAengine device is registered. An interrupt can therefore have queued a tasklet by the time a later registration step fails, but unregistering the DMAengine devices does not drain that tasklet before probe-owned storage is released.
Add tasklet cleanup actions to the DMAengine registration devres group. On failure, free the IRQ before releasing the group so no new tasklets can be scheduled, then unregister the DMAengine devices and drain their tasklets before freeing the remaining probe resources. Keep the managed registrations and cleanup actions in place on successful probe by removing only the temporary group markers.
--- drivers/dma/ste_dma40.c | 46 ++++++++++++++++++++++++++++++++++++++++++++-- 1 file changed, 44 insertions(+), 2 deletions(-)
drivers/dma/ste_dma40.c +44 -2
@@ -3047,6 +3047,18 @@ static void __init d40_chan_init(struct d40_base *base, struct dma_device *dma, } } +static void d40_kill_tasklets (void *data) +{ +struct dma_device *dma = data; +struct d40_chan *d40c; +struct dma_chan *chan; + +list_for_each_entry (chan, &dma->channels, device_node) { + d40c = container_of(chan, struct d40_chan, chan); +tasklet_kill (&d40c->tasklet); + } +} +static void d40_ops_init (struct d40_base *base,struct dma_device *dev) {if (dma_has_cap (DMA_SLAVE , dev->cap_mask)) {
@@ -3093,6 +3105,11 @@ static int __init d40_dmaengine_init(struct d40_base *base,d40_ops_init (base, &base->dma_slave); + err =devm_add_action_or_reset (base->dev, d40_kill_tasklets, + &base->dma_slave); +if (err) + goto exit; + err =dmaenginem_async_device_register (&base->dma_slave);if (err) {
@@ -3108,6 +3125,11 @@ static int __init d40_dmaengine_init(struct d40_base *base,d40_ops_init (base, &base->dma_memcpy); + err =devm_add_action_or_reset (base->dev, d40_kill_tasklets, + &base->dma_memcpy); +if (err) + goto exit; + err =dmaenginem_async_device_register (&base->dma_memcpy);if (err) {
@@ -3125,6 +3147,12 @@ static int __init d40_dmaengine_init(struct d40_base *base,dma_cap_set (DMA_CYCLIC , base->dma_both.cap_mask);d40_ops_init (base, &base->dma_both); + + err =devm_add_action_or_reset (base->dev, d40_kill_tasklets, + &base->dma_both); +if (err) + goto exit; + err =dmaenginem_async_device_register (&base->dma_both);if (err) {
@@ -3722,6 +3750,7 @@ static int __init d40_probe(struct platform_device *pdev)struct d40_base *base;struct resource *res;struct resource res_lcpa; +void *dmaenginem_reg_group;int num_reserved_chans;bool runtime_pm_enabled = false;bool irq_requested = false;
@@ -3855,20 +3884,33 @@ static int __init d40_probe(struct platform_device *pdev)d40_hw_init (base);enable_irq (base->irq); + dmaenginem_reg_group =devres_open_group (dev,NULL ,GFP_KERNEL ); +if (!dmaenginem_reg_group) { + ret = -ENOMEM ; + goto destroy_cache; + } + ret =d40_dmaengine_init (base, num_reserved_chans);if (ret) - goto destroy_cache; + goto release_dmaenginem; ret =of_dma_controller_register (np, d40_xlate,NULL );if (ret) {dev_err (dev,"could not register of_dma_controller\n" ); - goto destroy_cache; + goto release_dmaenginem; } +devres_remove_group (dev, dmaenginem_reg_group);dev_info (base->dev,"initialized\n" );return 0 ; + release_dmaenginem: +if (irq_requested) { +free_irq (base->irq, base); + irq_requested = false; + } +devres_release_group (dev, dmaenginem_reg_group); destroy_cache:if (base->lcla_pool.dma_addr) dma_unmap_single(base->dev, base->lcla_pool.dma_addr,
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 12/23 dmaengine: ste_dma40: Fix LCLA allocation order
In reply to Linus Walleijd40_lcla_allocate() calculates the number of pages needed for LCLA, but passes that raw page count as the allocation order to __get_free_pages(). The same value is later passed to free_pages().
Store the allocation order with get_order() instead, and use a separate byte size for allocation diagnostics, fallback kmalloc() sizing and DMA mapping.
--- drivers/dma/ste_dma40.c | 33 ++++++++++++++++----------------- 1 file changed, 16 insertions(+), 17 deletions(-)
drivers/dma/ste_dma40.c +16 -17
@@ -426,8 +426,8 @@ struct d40_desc {* @dma_addr: DMA address, if mapped * @base_unaligned: The original kmalloc pointer, if kmalloc is used. * This pointer is only there for clean-up on error. -* @pages: The number of pages needed for all physical channels. -* Only used later for clean-up on error +* @alloc_order: Order used for the LCLA page allocation. +* Only used later for clean-up on error. * @lock: Lock to protect the content in this struct. * @alloc_map: big map over which LCLA entry is own by which job. */
@@ -435,7 +435,7 @@ struct d40_lcla_pool {void *base;dma_addr_t dma_addr;void *base_unaligned; -int pages; +unsigned int alloc_order;spinlock_t lock;struct d40_desc **alloc_map; };
@@ -3611,6 +3611,7 @@ static void __init d40_hw_init(struct d40_base *base)static int __init d40_lcla_allocate (struct d40_base *base) {struct d40_lcla_pool *pool = &base->lcla_pool; +size_t lcla_size =SZ_1K * base->num_phy_chans;unsigned long *page_list;int i, j;int ret;
@@ -3626,20 +3627,20 @@ static int __init d40_lcla_allocate(struct d40_base *base)if (!page_list)return -ENOMEM ; -/* Calculating how many pages that are required */ - base->lcla_pool.pages =SZ_1K * base->num_phy_chans /PAGE_SIZE ; + base->lcla_pool.alloc_order =get_order (lcla_size);for (i =0 ; i <MAX_LCLA_ALLOC_ATTEMPTS ; i++) { page_list[i] =__get_free_pages (GFP_KERNEL , - base->lcla_pool.pages); + base->lcla_pool.alloc_order);if (!page_list[i]) { -d40_err (base->dev,"Failed to allocate %d pages.\n" , - base->lcla_pool.pages); +d40_err (base->dev,"Failed to allocate %zu bytes.\n" , + lcla_size); ret = -ENOMEM ;for (j =0 ; j < i; j++) -free_pages (page_list[j], base->lcla_pool.pages); +free_pages (page_list[j], + base->lcla_pool.alloc_order); goto free_page_list; }
@@ -3649,7 +3650,7 @@ static int __init d40_lcla_allocate(struct d40_base *base) }for (j =0 ; j < i; j++) -free_pages (page_list[j], base->lcla_pool.pages); +free_pages (page_list[j], base->lcla_pool.alloc_order);if (i <MAX_LCLA_ALLOC_ATTEMPTS ) { base->lcla_pool.base = (void *)page_list[i];
@@ -3659,10 +3660,9 @@ static int __init d40_lcla_allocate(struct d40_base *base)* alignment, try with allocating a big buffer. */ dev_warn (base->dev, -"[%s] Failed to get %d pages @ 18 bit align.\n" , - __func__, base->lcla_pool.pages); - base->lcla_pool.base_unaligned =kmalloc (SZ_1K * - base->num_phy_chans + +"[%s] Failed to get %zu bytes @ 18 bit align.\n" , + __func__, lcla_size); + base->lcla_pool.base_unaligned =kmalloc (lcla_size +LCLA_ALIGNMENT ,GFP_KERNEL );if (!base->lcla_pool.base_unaligned) {
@@ -3674,8 +3674,7 @@ static int __init d40_lcla_allocate(struct d40_base *base) LCLA_ALIGNMENT); } - pool->dma_addr =dma_map_single (base->dev, pool->base, -SZ_1K * base->num_phy_chans, + pool->dma_addr =dma_map_single (base->dev, pool->base, lcla_size,DMA_TO_DEVICE );if (dma_mapping_error (base->dev, pool->dma_addr)) { pool->dma_addr =0 ;
@@ -3919,7 +3918,7 @@ static int __init d40_probe(struct platform_device *pdev)if (!base->lcla_pool.base_unaligned && base->lcla_pool.base)free_pages ((unsigned long )base->lcla_pool.base, - base->lcla_pool.pages); + base->lcla_pool.alloc_order);kfree (base->lcla_pool.base_unaligned);
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 13/23 dmaengine: ste_dma40: Fix probe LCLA free
In reply to Linus WalleijWhen LCLA is placed in ESRAM, d40_probe() stores a devm_ioremap() address in lcla_pool.base and leaves base_unaligned unset. The destroy_cache error path can then pass the ioremap address to free_pages().
Only free lcla_pool.base with free_pages() when the driver allocated the LCLA pool from normal memory. The ESRAM mapping is devm-managed.
--- drivers/dma/ste_dma40.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/dma/ste_dma40.c +2 -1
@@ -3916,7 +3916,8 @@ static int __init d40_probe(struct platform_device *pdev)SZ_1K * base->num_phy_chans, DMA_TO_DEVICE); -if (!base->lcla_pool.base_unaligned && base->lcla_pool.base) +if (!base->plat_data->use_esram_lcla && + !base->lcla_pool.base_unaligned && base->lcla_pool.base)free_pages ((unsigned long )base->lcla_pool.base, base->lcla_pool.alloc_order);
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 14/23 dmaengine: ste_dma40: Put the LCPA SRAM node
In reply to Linus Walleijof_parse_phandle() takes a reference to the LCPA SRAM node, but d40_probe() does not release it after translating the node into a resource. This leaks the node reference for the lifetime of the system.
Put the node immediately after of_address_to_resource() so both the success and error paths release the reference.
--- drivers/dma/ste_dma40.c | 1 + 1 file changed, 1 insertion(+)
drivers/dma/ste_dma40.c +1 -0
@@ -3781,6 +3781,7 @@ static int __init d40_probe(struct platform_device *pdev) }/* This is no device so read the address directly from the node */ ret =of_address_to_resource (np_lcpa,0 , &res_lcpa); +of_node_put (np_lcpa);if (ret) {dev_err (dev,"no LCPA SRAM resource\n" ); goto report_failure;
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 15/23 dmaengine: ste_dma40: Fix memcpy channel parsing
In reply to Linus Walleijd40_of_probe() validates the memcpy-channels property against D40_MEMCPY_MAX_CHANS, but reads the property directly into a smaller global array. A long property can therefore overwrite adjacent data. The mutable global also lets a later DMA40 instance replace the memcpy channel mapping used for future allocations on an earlier instance.
Store the mapping in the per-device platform data, validate the property against that storage, and check the property read result. The property is required and d40_probe() always populates the platform data, so remove the obsolete global mapping and fallback.
--- drivers/dma/ste_dma40.c | 45 ++++++++++++++------------------------------- 1 file changed, 14 insertions(+), 31 deletions(-)
drivers/dma/ste_dma40.c +14 -31
@@ -28,6 +28,8 @@#include "ste_dma40.h" #include "ste_dma40_ll.h" +#define D40_MEMCPY_MAX_CHANS 8 +/** * struct stedma40_platform_data - Configuration struct for the dma device. *
@@ -41,6 +43,7 @@* to use SoftLLI. * @use_esram_lcla: flag for mapping the lcla into esram region * @num_of_memcpy_chans: The number of channels reserved for memcpy. +* @memcpy_channels: The event lines used for memcpy. * @num_of_phy_chans: The number of physical channels implemented in HW. * 0 means reading the number of channels from DMA HW but this is only valid * for 'multiple of 4' channels, like 8.
@@ -51,6 +54,7 @@ struct stedma40_platform_data {int num_of_soft_lli_chans;bool use_esram_lcla;int num_of_memcpy_chans; +u32 memcpy_channels[D40_MEMCPY_MAX_CHANS ];int num_of_phy_chans; };
@@ -89,25 +93,6 @@ struct stedma40_platform_data {#define D40_ALLOC_PHY BIT(30)#define D40_ALLOC_LOG_FREE 0 -#define D40_MEMCPY_MAX_CHANS 8 - -/* Reserved event lines for memcpy only. */ -#define DB8500_DMA_MEMCPY_EV_0 51 -#define DB8500_DMA_MEMCPY_EV_1 56 -#define DB8500_DMA_MEMCPY_EV_2 57 -#define DB8500_DMA_MEMCPY_EV_3 58 -#define DB8500_DMA_MEMCPY_EV_4 59 -#define DB8500_DMA_MEMCPY_EV_5 60 - -static int dma40_memcpy_channels[] = { -DB8500_DMA_MEMCPY_EV_0 , -DB8500_DMA_MEMCPY_EV_1 , -DB8500_DMA_MEMCPY_EV_2 , -DB8500_DMA_MEMCPY_EV_3 , -DB8500_DMA_MEMCPY_EV_4 , -DB8500_DMA_MEMCPY_EV_5 , -}; -/* Default configuration for physical memcpy */ static const struct stedma40_chan_cfg dma40_memcpy_conf_phy = { .mode =STEDMA40_MODE_PHYSICAL ,
@@ -2157,7 +2142,8 @@ static int d40_config_memcpy(struct d40_chan *d40c)if (dma_has_cap (DMA_MEMCPY , cap) && !dma_has_cap (DMA_SLAVE , cap)) { d40c->dma_cfg = dma40_memcpy_conf_log; - d40c->dma_cfg.dev_type = dma40_memcpy_channels[d40c->chan.chan_id]; + d40c->dma_cfg.dev_type = + d40c->base->plat_data->memcpy_channels[d40c->chan.chan_id];d40_log_cfg (&d40c->dma_cfg, &d40c->log_def.lcsp1, &d40c->log_def.lcsp3);
@@ -3442,12 +3428,7 @@ static int __init d40_hw_detect_init(struct platform_device *pdev, num_phy_chans =min (num_phy_chans,STEDMA40_MAX_PHYS );/* The number of channels used for memcpy */ -if (plat_data->num_of_memcpy_chans) - num_memcpy_chans = plat_data->num_of_memcpy_chans; -else - num_memcpy_chans =ARRAY_SIZE (dma40_memcpy_channels); - - num_memcpy_chans =min (num_memcpy_chans,D40_MEMCPY_MAX_CHANS ); + num_memcpy_chans = plat_data->num_of_memcpy_chans; num_log_chans = num_phy_chans *D40_MAX_LOG_CHAN_PER_PHY ; dev_info(dev,
@@ -3696,6 +3677,7 @@ static int __init d40_of_probe(struct device *dev,struct stedma40_platform_data *pdata;int num_phy =0 , num_memcpy =0 , num_disabled =0 ;const __be32 *list; +int ret; pdata =devm_kzalloc (dev,sizeof (*pdata),GFP_KERNEL );if (!pdata)
@@ -3709,18 +3691,19 @@ static int __init d40_of_probe(struct device *dev, list =of_get_property (np,"memcpy-channels" , &num_memcpy); num_memcpy /=sizeof (*list); -if (num_memcpy >D40_MEMCPY_MAX_CHANS || num_memcpy <=0 ) { +if (num_memcpy >ARRAY_SIZE (pdata->memcpy_channels) || + num_memcpy <=0 ) {d40_err (dev,"Invalid number of memcpy channels specified (%d)\n" , num_memcpy);return -EINVAL ; } + ret =of_property_read_u32_array (np,"memcpy-channels" , + pdata->memcpy_channels, num_memcpy); +if (ret) +return ret; pdata->num_of_memcpy_chans = num_memcpy; -of_property_read_u32_array (np,"memcpy-channels" , - dma40_memcpy_channels, - num_memcpy); - list =of_get_property (np,"disabled-channels" , &num_disabled); num_disabled /=sizeof (*list);
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 16/23 dmaengine: ste_dma40: Validate disabled channel indexes
In reply to Linus Walleijd40_of_probe() checks how many entries disabled-channels contains, but not the channel numbers themselves. d40_phy_res_init() later uses every value as an index into base->phy_res, whose size is the number of channels found in this DMA40 instance. An out-of-range value can therefore write beyond the allocation.
Validate each disabled channel against the detected hardware channel count before allocating and initializing the channel resources.
--- drivers/dma/ste_dma40.c | 9 +++++++++ 1 file changed, 9 insertions(+)
drivers/dma/ste_dma40.c +9 -0
@@ -3427,6 +3427,15 @@ static int __init d40_hw_detect_init(struct platform_device *pdev, num_phy_chans =min (num_phy_chans,STEDMA40_MAX_PHYS ); +for (i =0 ; plat_data->disabled_channels[i] !=-1 ; i++) { +int chan = plat_data->disabled_channels[i]; + +if (chan <0 || chan >= num_phy_chans) { +dev_err (dev,"Invalid disabled channel %d\n" , chan); +return -EINVAL ; + } + } +/* The number of channels used for memcpy */ num_memcpy_chans = plat_data->num_of_memcpy_chans; num_log_chans = num_phy_chans *D40_MAX_LOG_CHAN_PER_PHY ;
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 17/23 dmaengine: ste_dma40: Validate DMA specifier length
In reply to Linus WalleijThe DMA40 binding requires three cells, but d40_xlate() reads args[0], args[1], and args[2] without checking args_count. A malformed provider node can specify fewer cells, leaving some of these values uninitialized when the OF DMA core invokes the translation callback.
Reject specifiers that do not contain exactly three cells before reading the argument array.
--- drivers/dma/ste_dma40.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/dma/ste_dma40.c +3 -0
@@ -2550,6 +2550,9 @@ static struct dma_chan *d40_xlate(struct of_phandle_args *dma_spec,dma_cap_mask_t cap;u32 flags; +if (dma_spec->args_count !=3 ) +return NULL ; +memset (&cfg,0 ,sizeof (struct stedma40_chan_cfg ));dma_cap_zero (cap);
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 18/23 dmaengine: ste_dma40: Reject direction changes after allocation
In reply to Linus WalleijLogical channel allocation uses the configured direction to select the source or destination allocation mask, derive the logical channel number, and choose the LCPA location.
d40_set_runtime_config_write() nevertheless overwrites the configured direction when a transfer is prepared for the opposite direction. d40_free_dma() then clears the wrong allocation mask, leaking the original resource and potentially releasing one used by another client.
Reject directions that differ from the direction used during allocation and propagate runtime configuration errors to callers. Skip slave runtime configuration for memcpy transfers, which also use d40_prep_sg() but do not require it.
--- drivers/dma/ste_dma40.c | 29 ++++++++++++++--------------- 1 file changed, 14 insertions(+), 15 deletions(-)
drivers/dma/ste_dma40.c +14 -15
@@ -2418,7 +2418,13 @@ d40_prep_sg(struct dma_chan *dchan, struct scatterlist *sg_src,return NULL ; } -d40_set_runtime_config_write (dchan, &chan->slave_config, direction); +if (direction !=DMA_MEM_TO_MEM ) { + ret =d40_set_runtime_config_write (dchan, + &chan->slave_config, + direction); +if (ret) +return NULL ; + }spin_lock_irqsave (&chan->lock, flags);
@@ -2894,6 +2900,13 @@ static int d40_set_runtime_config_write(struct dma_chan *chan,return -EINVAL ; } +if (direction != cfg->dir) { +chan_err (d40c, +"transfer direction %d differs from allocated direction %d\n" , + direction, cfg->dir); +return -EINVAL ; + } + src_addr_width = config->src_addr_width; src_maxburst = config->src_maxburst; dst_addr_width = config->dst_addr_width;
@@ -2902,13 +2915,6 @@ static int d40_set_runtime_config_write(struct dma_chan *chan,if (direction ==DMA_DEV_TO_MEM ) { config_addr = config->src_addr; -if (cfg->dir !=DMA_DEV_TO_MEM ) -dev_dbg (d40c->base->dev, -"channel was not configured for peripheral " -"to memory transfer (%d) overriding\n" , - cfg->dir); - cfg->dir =DMA_DEV_TO_MEM ; -/* Configure the memory side */ if (dst_addr_width ==DMA_SLAVE_BUSWIDTH_UNDEFINED ) dst_addr_width = src_addr_width;
@@ -2918,13 +2924,6 @@ static int d40_set_runtime_config_write(struct dma_chan *chan, }else if (direction ==DMA_MEM_TO_DEV ) { config_addr = config->dst_addr; -if (cfg->dir !=DMA_MEM_TO_DEV ) -dev_dbg (d40c->base->dev, -"channel was not configured for memory " -"to peripheral transfer (%d) overriding\n" , - cfg->dir); - cfg->dir =DMA_MEM_TO_DEV ; -/* Configure the memory side */ if (src_addr_width ==DMA_SLAVE_BUSWIDTH_UNDEFINED ) src_addr_width = dst_addr_width;
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 19/23 dmaengine: ste_dma40: Fix logical channel bounds check
In reply to Linus Walleijd40_validate_conf() checks the raw dev_type against num_log_chans, but d40_allocate_channel() derives the lookup_log_chans index as either 2 * dev_type or 2 * dev_type + 1.
Validate the dev_type against the derived logical channel index limit so channel allocation cannot write past lookup_log_chans.
--- drivers/dma/ste_dma40.c | 17 ++++++++++++++--- 1 file changed, 14 insertions(+), 3 deletions(-)
drivers/dma/ste_dma40.c +14 -3
@@ -1884,15 +1884,26 @@ static int d40_validate_conf(struct d40_chan *d40c, {int res =0 ;bool is_log = conf->mode ==STEDMA40_MODE_LOGICAL ; +bool invalid_dev_type = conf->dev_type <0 ;if (!conf->dir) {chan_err (d40c,"Invalid direction.\n" ); res = -EINVAL ; } -if ((is_log && conf->dev_type > d40c->base->num_log_chans) || - (!is_log && conf->dev_type > d40c->base->num_phy_chans) || - (conf->dev_type <0 )) { +if (!invalid_dev_type && is_log) { +int max_dev_type; + +if (conf->dir ==DMA_DEV_TO_MEM ) + max_dev_type =DIV_ROUND_UP (d40c->base->num_log_chans,2 ); +else + max_dev_type = d40c->base->num_log_chans /2 ; + + invalid_dev_type = conf->dev_type >= max_dev_type; + } + +if (invalid_dev_type || + (!is_log && conf->dev_type > d40c->base->num_phy_chans)) {chan_err (d40c,"Invalid device type (%d)\n" , conf->dev_type); res = -EINVAL ; }
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 20/23 dmaengine: ste_dma40: Fix event group bounds
In reply to Linus WalleijThe dev_type validation can allow values whose derived event group has no matching physical channel pair. d40_allocate_channel() then indexes phy_res with j + event_group * 2, and __d40_set_prio_rt() uses the same group to select priority and realtime registers.
The physical-mode validation also compares dev_type with the number of physical channels. However, dev_type identifies an event line: DB8500 has eight physical channels but 64 source and 64 destination event lines. The event group determines which physical channel pair can serve an event, so the physical channel count is not a valid dev_type limit.
Reject dev_type values outside the hardware event-group range, remove the incorrect physical channel count limit, and stop the physical-channel search before a partial final channel group can index past phy_res.
--- drivers/dma/ste_dma40.c | 26 ++++++++++++++++++++++---- 1 file changed, 22 insertions(+), 4 deletions(-)
drivers/dma/ste_dma40.c +22 -4
@@ -82,6 +82,10 @@ struct stedma40_platform_data {#define D40_LCLA_LINK_PER_EVENT_GRP 128#define D40_LCLA_END D40_LCLA_LINK_PER_EVENT_GRP +/* Number of event groups per hardware register layout */ +#define D40_EVENT_GROUPS_V4A 4 +#define D40_EVENT_GROUPS_V4B 5 +/* Max number of logical channels per physical channel */ #define D40_MAX_LOG_CHAN_PER_PHY 32
@@ -522,6 +526,7 @@ struct d40_chan {* @high_prio_clear: the high priority clear register * @interrupt_en: the interrupt enable register * @interrupt_clear: the interrupt clear register +* @num_event_groups: number of supported event groups * @il: the pointer to struct d40_interrupt_lookup * @il_size: the size of d40_interrupt_lookup array * @init_reg: the pointer to the struct d40_reg_val
@@ -536,6 +541,7 @@ struct d40_gen_dmac {u32 high_prio_clear;u32 interrupt_en;u32 interrupt_clear; +u32 num_event_groups;struct d40_interrupt_lookup *il;u32 il_size;struct d40_reg_val *init_reg;
@@ -1886,6 +1892,11 @@ static int d40_validate_conf(struct d40_chan *d40c,bool is_log = conf->mode ==STEDMA40_MODE_LOGICAL ;bool invalid_dev_type = conf->dev_type <0 ; +if (!invalid_dev_type && +D40_TYPE_TO_GROUP (conf->dev_type) >= + d40c->base->gen_dmac.num_event_groups) + invalid_dev_type = true; +if (!conf->dir) {chan_err (d40c,"Invalid direction.\n" ); res = -EINVAL ;
@@ -1902,8 +1913,7 @@ static int d40_validate_conf(struct d40_chan *d40c, invalid_dev_type = conf->dev_type >= max_dev_type; } -if (invalid_dev_type || - (!is_log && conf->dev_type > d40c->base->num_phy_chans)) { +if (invalid_dev_type) {chan_err (d40c,"Invalid device type (%d)\n" , conf->dev_type); res = -EINVAL ; }
@@ -2068,8 +2078,12 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user) } } }else -for (j =0 ; j < d40c->base->num_phy_chans; j +=8 ) { +for (j =0 ; j < d40c->base->num_phy_chans; + j +=D40_GROUP_SIZE ) {int phy_num = j + event_group *2 ; +if (phy_num +1 >= num_phy_chans) +break ; +for (i = phy_num; i < phy_num +2 ; i++) { if (d40_alloc_mask_set(&phys[i], is_src,
@@ -2089,8 +2103,10 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)return -EINVAL ;/* Find logical channel */ -for (j =0 ; j < d40c->base->num_phy_chans; j +=8 ) { +for (j =0 ; j < d40c->base->num_phy_chans; j +=D40_GROUP_SIZE ) {int phy_num = j + event_group *2 ; +if (phy_num +1 >= num_phy_chans) +break ;if (d40c->dma_cfg.use_fixed_channel) { i = d40c->dma_cfg.phy_channel;
@@ -3475,6 +3491,7 @@ static int __init d40_hw_detect_init(struct platform_device *pdev, base->log_chans = &base->phy_chans[num_phy_chans];if (base->plat_data->num_of_phy_chans ==14 ) { + base->gen_dmac.num_event_groups =D40_EVENT_GROUPS_V4B ; base->gen_dmac.backup = d40_backup_regs_v4b; base->gen_dmac.backup_size =BACKUP_REGS_SZ_V4B ; base->gen_dmac.interrupt_en =D40_DREG_CPCMIS ;
@@ -3488,6 +3505,7 @@ static int __init d40_hw_detect_init(struct platform_device *pdev, base->gen_dmac.init_reg = dma_init_reg_v4b; base->gen_dmac.init_reg_size =ARRAY_SIZE (dma_init_reg_v4b); }else { + base->gen_dmac.num_event_groups =D40_EVENT_GROUPS_V4A ;if (base->rev >=3 ) { base->gen_dmac.backup = d40_backup_regs_v4a; base->gen_dmac.backup_size =BACKUP_REGS_SZ_V4A ;
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 21/23 dmaengine: ste_dma40: Search all blocks for fixed logical channels
In reply to Linus WalleijFixed logical channel allocation scans physical channels in blocks of eight. When the requested physical channel does not belong to the first block, d40_allocate_channel() returns -EINVAL instead of checking later blocks.
Skip nonmatching blocks so controllers with more than eight physical channels can allocate fixed logical channels from the later blocks.
--- drivers/dma/ste_dma40.c | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-)
drivers/dma/ste_dma40.c +2 -5
@@ -2111,11 +2111,8 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)if (d40c->dma_cfg.use_fixed_channel) { i = d40c->dma_cfg.phy_channel; -if ((i != phy_num) && (i != phy_num +1 )) { -dev_err (chan2dev (d40c), -"invalid fixed phy channel %d\n" , i); -return -EINVAL ; - } +if (i != phy_num && i != phy_num +1 ) +continue ;if (d40_alloc_mask_set (&phys[i], is_src, event_line, is_log, first_phy_user))
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 22/23 dmaengine: ste_dma40: Validate fixed physical channel indexes
In reply to Linus WalleijFixed physical memcpy allocation uses dma_cfg.phy_channel directly as an index into phy_res when use_fixed_channel is set. d40_validate_conf() validates dev_type but not the fixed physical channel, allowing an invalid configuration to access memory outside the array.
Validate the fixed physical channel centrally before accepting the channel configuration.
--- drivers/dma/ste_dma40.c | 8 ++++++++ 1 file changed, 8 insertions(+)
drivers/dma/ste_dma40.c +8 -0
@@ -1918,6 +1918,14 @@ static int d40_validate_conf(struct d40_chan *d40c, res = -EINVAL ; } +if (conf->use_fixed_channel && + (conf->phy_channel <0 || + conf->phy_channel >= d40c->base->num_phy_chans)) { +chan_err (d40c,"Invalid physical channel (%d)\n" , + conf->phy_channel); + res = -EINVAL ; + } +if (conf->dir ==DMA_DEV_TO_DEV ) {/* * DMAC HW supports it. Will be added to this driver,
Signature · 1 line
2.55.0
Linus Walleij
maintainerPATCH v5 23/23 dmaengine: ste_dma40: Validate memcpy configuration
In reply to Linus Walleijd40_config_memcpy() builds a default memcpy configuration without passing it through d40_validate_conf(). A dev_type supplied through the memcpy-channels device tree property can therefore bypass the bounds checks added for client configurations.
The generic DMA direction enum assigns zero to DMA_MEM_TO_MEM, unlike DMA40's old private enum. Allow memory-to-memory directions in the validator so checking the generated configuration does not reject all memcpy channels.
Validate the generated memcpy configuration before deriving logical channel registers or allocating the channel.
--- drivers/dma/ste_dma40.c | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-)
drivers/dma/ste_dma40.c +11 -1
@@ -1897,7 +1897,8 @@ static int d40_validate_conf(struct d40_chan *d40c, d40c->base->gen_dmac.num_event_groups) invalid_dev_type = true; -if (!conf->dir) { +if (conf->dir !=DMA_MEM_TO_MEM && + !is_slave_direction (conf->dir)) {chan_err (d40c,"Invalid direction.\n" ); res = -EINVAL ; }
@@ -2171,12 +2172,17 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)static int d40_config_memcpy (struct d40_chan *d40c) {dma_cap_mask_t cap = d40c->chan.device->cap_mask; +int ret;if (dma_has_cap (DMA_MEMCPY , cap) && !dma_has_cap (DMA_SLAVE , cap)) { d40c->dma_cfg = dma40_memcpy_conf_log; d40c->dma_cfg.dev_type = d40c->base->plat_data->memcpy_channels[d40c->chan.chan_id]; + ret =d40_validate_conf (d40c, &d40c->dma_cfg); +if (ret) +return ret; +d40_log_cfg (&d40c->dma_cfg, &d40c->log_def.lcsp1, &d40c->log_def.lcsp3);
@@ -2184,6 +2190,10 @@ static int d40_config_memcpy(struct d40_chan *d40c) dma_has_cap(DMA_SLAVE, cap)) { d40c->dma_cfg = dma40_memcpy_conf_phy; + ret =d40_validate_conf (d40c, &d40c->dma_cfg); +if (ret) +return ret; +/* Generate interrupt at end of transfer or relink. */ d40c->dst_def_cfg |=BIT (D40_SREG_CFG_TIM_POS );
Signature · 1 line
2.55.0
Linus Walleij
maintainerQuoted 11 lines · Linus Walleij
This series fixes 26 DMA40 bugs.
12 were found while reviewing the Ux500 LCLA SRAM power-domain conversion.
The cyclic transfer residue bug was exposed by Ux500 audio playback.
13 more issues were identified during review and hardware-manual audit.
The method taken is: whenever Sashiko complains: fix the bug it complains about if possible.
Quoted 6 lines
This has been boot tested on the Samsung Skomer device: DMA for MMC, wireless SDIO and UART still works after these patches, and DMA for audio started working.
Assisted-by LLMSigned-off-by Linus Walleij <[email protected]>
Ugh I managed to not update the patch series from v5 to v6 ... OK let me fix this up, wait a few days and resend.
I guess I'm getting a bit worn out by this fix series that started as a few fixes and just grows wildly thanks to / due to the massive AI review from Sashiko.
Yours,
Linus Walleij