Skip to contentSkip to conversation

spi: dw: use threaded interrupt

PATCH Superseded Jisheng Zhang 2 participants 7 messages Sep 29 SPI

v4 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#0 lore raw

v4 cover spi: dw: use threaded interrupt

To avoid blocking for an excessive amount of time, eventually impacting on system responsiveness, hard interrupt handlers should finish executing in as little time as possible.

Use threaded interrupt and move the SPI transfer handling to an interrupt thread when non-native CS and host only.

After that, since the dw_reader() and dw_writer() are called in threaded ISR now, so we can delay the unmasking interrupts until no rx and tx action is taken, thus reduce the interrupt numbers further.

Tested with below two cmds
./spidev_test -D /dev/spidev1.3 -s 30000000 -S 327680 -I 1

./spidev_test -D /dev/spidev1.3 -s 30000000 -S 327680 -I 1000 ./rtla timerlat top -q -k -P f:95

The first cmd is to check the interrupt numbers optmizaion result, the 2nd cmd group is to check the threaded interrupt improvement.

Before the patch:
each 320KB spi spidev_test transfer triggers 33118 interrupts

spidev_test reports ~22090 kbps
and rtla reports:
Timer Latency

  0 00:00:37   |          IRQ Timer Latency (us)        |         Thread Timer Latency (us)
CPU COUNT      |      cur       min       avg       max |      cur       min       avg       max
  0 #9958      |        1         0        67    103394 |        6         4      2198    105031
  1 #36902     |        1         0         1        18 |        5         4         5        29

After the patch:
each 320KB spi spidev_test transfer only triggers 1 interrupts spidev_test reports ~23520 kbps
and now rtla reports:
Timer Latency

  0 00:00:58   |          IRQ Timer Latency (us)        |         Thread Timer Latency (us)
CPU COUNT      |      cur       min       avg       max |      cur       min       avg       max
  0 #58362     |        1         0         0        29 |        6         3         4        56
  1 #58363     |        1         0         1        23 |        6         4         5        68

In summary:
before the patch after the patch
33118 interrutps 1 interrupts reduced by 33117 times!
103394 us max latency 29 us max latency reduced by 3564 times!
22090 kbps rate 23520 kbps rate improved by 6.5%

Since v3:
- If native cs, don't use threaded interrupt
- do one round of FIFO in the hardirq
- add cond_resched in dw_spi_irq_thread_fn

Since v2:
- rebase against latest version
- remove the "spi: dw: use DW_SPI_INT_MASK instead of hardcoded 0xff"
- add three more patches to clean up irq code introduced by recent "enhanced spi" support
- Don't use threaded interrupt for target mode and the enhanced spi

Since v1:
- rebase against latest version
- drop two patches which have been merged
- correct some performance numbers
- don't move request irq code block so no changes for err handling code path
- move spi_finalize_current_transfer to the end of threaded irq fn
- don't rely on irq status in threaded fn, but try rx and tx as much as possible in the loop

Jisheng Zhang (5):
spi: dw: use DW_SPI_ISR directly
spi: dw: remove useless dws->transfer_handler check
spi: dw: remove duplicated "!rx_len && !tx_len" handling from
dw_spi_irq
spi: dw: restore previous irq handling behavior when !ctlr->cur_msg
spi: dw: use threaded interrupt and optimize the threaded ISR

 drivers/spi/spi-dw-core.c | 78 ++++++++++++++++++++++++++++++++-------
 1 file changed, 64 insertions(+), 14 deletions(-)
Signature · 1 line
2.53.0
#1 lore raw

PATCH v4 1/5 spi: dw: use DW_SPI_ISR directly

The DW_SPI_ISR register reports the masked interrupts, no need to mask again.

---
 drivers/spi/spi-dw-core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/spi/spi-dw-core.c +1 -1
index 206d3f9dd83d..1c060f0ec50c 100644
@@ -275,7 +275,7 @@ static irqreturn_t dw_spi_irq(int irq, void *dev_id)
 {
 	struct spi_controller *ctlr = dev_id;
 	struct dw_spi *dws = spi_controller_get_devdata(ctlr);
-	u16 irq_status = dw_readl(dws, DW_SPI_ISR) & DW_SPI_INT_MASK;
+	u16 irq_status = dw_readl(dws, DW_SPI_ISR);
 
 	if (!irq_status)
 		return IRQ_NONE;
Signature · 1 line
2.53.0
#2 lore raw

PATCH v4 2/5 spi: dw: remove useless dws->transfer_handler check

In reply to Jisheng Zhang

transfer_handler is initialized before any DW SPI interrupt is unmasked. While the IRQ is registered but the handler is NULL, dw_spi_hw_init() has all DW SPI interrupts disabled. Therefore dw_spi_irq() cannot observe a DW SPI interrupt with a NULL transfer_handler.

---
 drivers/spi/spi-dw-core.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/spi/spi-dw-core.c +1 -2
index 1c060f0ec50c..f4c4e9dae25e 100644
@@ -280,8 +280,7 @@ static irqreturn_t dw_spi_irq(int irq, void *dev_id)
 	if (!irq_status)
 		return IRQ_NONE;
 
-	if (!dws->transfer_handler ||
-	    (!ctlr->cur_msg && dws->transfer_handler == dw_spi_transfer_handler)) {
+	if (!ctlr->cur_msg && dws->transfer_handler == dw_spi_transfer_handler) {
 		dw_spi_mask_intr(dws, 0xff);
 		return IRQ_HANDLED;
 	}
Signature · 1 line
2.53.0
#3 lore raw

PATCH v4 3/5 spi: dw: remove duplicated "!rx_len && !tx_len" handling from dw_spi_irq

In reply to Jisheng Zhang

dw_spi_irq() need not handle enhanced-transfer's "!rx_len && !tx_len" case as that state is already handled by dw_spi_enh_handler()

---
 drivers/spi/spi-dw-core.c | 6 ------
 1 file changed, 6 deletions(-)
drivers/spi/spi-dw-core.c +0 -6
index f4c4e9dae25e..91de357f97f3 100644
@@ -284,12 +284,6 @@ static irqreturn_t dw_spi_irq(int irq, void *dev_id)
 		dw_spi_mask_intr(dws, 0xff);
 		return IRQ_HANDLED;
 	}
-	if (dws->transfer_handler == dw_spi_enh_handler &&
-	    !dws->rx_len && !dws->tx_len) {
-		dw_spi_mask_intr(dws, 0xff);
-		spi_finalize_current_transfer(ctlr);
-		return IRQ_HANDLED;
-	}
 
 	return dws->transfer_handler(dws);
 }
Signature · 1 line
2.53.0
#4 lore raw

PATCH v4 4/5 spi: dw: restore previous irq handling behavior when !ctlr->cur_msg

In reply to Jisheng Zhang

Recent "enhanced" support changes the dw_spi_irq() behavior a bit when !!ctlr->cur_msg:

    if (!ctlr->cur_msg && dws->transfer_handler == dw_spi_transfer_handler) {
            dw_spi_mask_intr(dws, 0xff);
            return IRQ_HANDLED;
    }

But it misses the dma case, where the transfer_handler == dw_spi_dma_transfer_handler, so this changes the previous long time working behavior, let's restore the previous handling by only filtering out the dw_spi_enh_handler.

---
 drivers/spi/spi-dw-core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/spi/spi-dw-core.c +1 -1
index 91de357f97f3..da7d4872e513 100644
@@ -280,7 +280,7 @@ static irqreturn_t dw_spi_irq(int irq, void *dev_id)
 	if (!irq_status)
 		return IRQ_NONE;
 
-	if (!ctlr->cur_msg && dws->transfer_handler == dw_spi_transfer_handler) {
+	if (!ctlr->cur_msg && dws->transfer_handler != dw_spi_enh_handler) {
 		dw_spi_mask_intr(dws, 0xff);
 		return IRQ_HANDLED;
 	}
Signature · 1 line
2.53.0
#5 lore raw

PATCH v4 5/5 spi: dw: use threaded interrupt and optimize the threaded ISR

In reply to Jisheng Zhang

To avoid blocking for an excessive amount of time, eventually impacting on system responsiveness, hard interrupt handlers should finish executing in as little time as possible.

Use threaded interrupt and move the SPI transfer handling to an interrupt thread when non-native CS and host only.

After that, since the dw_reader() and dw_writer() are called in threaded ISR now, so we can delay the unmasking interrupts until no rx and tx action is taken, thus reduce the interrupt numbers further.

Tested with below two cmds
./spidev_test -D /dev/spidev1.3 -s 30000000 -S 327680 -I 1

./spidev_test -D /dev/spidev1.3 -s 30000000 -S 327680 -I 1000 ./rtla timerlat top -q -k -P f:95

The first cmd is to check the interrupt numbers optmizaion result, the 2nd cmd group is to check the threaded interrupt improvement.

Before the patch:
each 320KB spi spidev_test transfer triggers 33118 interrupts

spidev_test reports ~22090 kbps
and rtla reports:
Timer Latency

  0 00:00:37   |          IRQ Timer Latency (us)        |         Thread Timer Latency (us)
CPU COUNT      |      cur       min       avg       max |      cur       min       avg       max
  0 #9958      |        1         0        67    103394 |        6         4      2198    105031
  1 #36902     |        1         0         1        18 |        5         4         5        29

After the patch:
each 320KB spi spidev_test transfer only triggers 1 interrupts spidev_test reports ~23520 kbps
and now rtla reports:
Timer Latency

  0 00:00:58   |          IRQ Timer Latency (us)        |         Thread Timer Latency (us)
CPU COUNT      |      cur       min       avg       max |      cur       min       avg       max
  0 #58362     |        1         0         0        29 |        6         3         4        56
  1 #58363     |        1         0         1        23 |        6         4         5        68

In summary:
before the patch after the patch
33118 interrutps 1 interrupts reduced by 33117 times!
103394 us max latency 29 us max latency reduced by 3564 times!
22090 kbps rate 23520 kbps rate improved by 6.5%

---
 drivers/spi/spi-dw-core.c | 67 ++++++++++++++++++++++++++++++++++++---
 1 file changed, 62 insertions(+), 5 deletions(-)
drivers/spi/spi-dw-core.c +62 -5
index da7d4872e513..bd86cbe8fcfe 100644
@@ -132,10 +132,11 @@ static inline u32 dw_spi_rx_max(struct dw_spi *dws)
 	return min_t(u32, dws->rx_len, dw_readl(dws, DW_SPI_RXFLR));
 }
 
-static void dw_writer(struct dw_spi *dws)
+static u32 dw_writer(struct dw_spi *dws)
 {
 	u32 max = dw_spi_tx_max(dws);
 	u32 txw = 0;
+	u32 tx = 0;
 
 	while (max--) {
 		if (dws->tx) {
@@ -150,13 +151,16 @@ static void dw_writer(struct dw_spi *dws)
 		}
 		dw_write_io_reg(dws, DW_SPI_DR, txw);
 		--dws->tx_len;
+		++tx;
 	}
+	return tx;
 }
 
-static void dw_reader(struct dw_spi *dws)
+static u32 dw_reader(struct dw_spi *dws)
 {
 	u32 max = dw_spi_rx_max(dws);
 	u32 rxw;
+	u32 rx = 0;
 
 	while (max--) {
 		rxw = dw_read_io_reg(dws, DW_SPI_DR);
@@ -171,7 +175,9 @@ static void dw_reader(struct dw_spi *dws)
 			dws->rx += dws->n_bytes;
 		}
 		--dws->rx_len;
+		++rx;
 	}
+	return rx;
 }
 
 int dw_spi_check_status(struct dw_spi *dws, bool raw)
@@ -210,6 +216,51 @@ int dw_spi_check_status(struct dw_spi *dws, bool raw)
 }
 EXPORT_SYMBOL_NS_GPL(dw_spi_check_status, "SPI_DW_CORE");
 
+static irqreturn_t dw_spi_irq_thread_fn(int irq, void *dev_id)
+{
+	struct spi_controller *ctlr = dev_id;
+	struct dw_spi *dws = spi_controller_get_devdata(ctlr);
+	u32 rx, tx, imask, mask = 0;
+	bool finalize = false;
+
+	do {
+		/*
+		 * Read data from the Rx FIFO every time we've got a chance executing
+		 * this method. If there is nothing left to receive, terminate the
+		 * procedure. Otherwise adjust the Rx FIFO Threshold level if it's a
+		 * final stage of the transfer. By doing so we'll get the next IRQ
+		 * right when the leftover incoming data is received.
+		 */
+		rx = dw_reader(dws);
+		if (!dws->rx_len) {
+			mask |= 0xff;
+			finalize = true;
+		} else if (dws->rx_len <= dw_readl(dws, DW_SPI_RXFTLR)) {
+			dw_writel(dws, DW_SPI_RXFTLR, dws->rx_len - 1);
+		}
+
+		/*
+		 * Send data out as much as possible. The Tx FIFO Empty IRQ will be
+		 * disabled after the data transmission is finished so not to
+		 * have the TXE IRQ flood at the final stage of the transfer.
+		 */
+		tx = dw_writer(dws);
+		if (!dws->tx_len)
+			mask |= DW_SPI_INT_TXEI;
+		cond_resched();
+	} while (rx != 0 || tx != 0);
+
+	imask = DW_SPI_INT_TXEI | DW_SPI_INT_TXOI |
+		DW_SPI_INT_RXUI | DW_SPI_INT_RXOI | DW_SPI_INT_RXFI;
+	imask &= ~mask;
+	dw_spi_umask_intr(dws, imask);
+
+	if (finalize)
+		spi_finalize_current_transfer(dws->ctlr);
+
+	return IRQ_HANDLED;
+}
+
 static irqreturn_t dw_spi_transfer_handler(struct dw_spi *dws)
 {
 	u16 irq_status = dw_readl(dws, DW_SPI_ISR);
@@ -245,7 +296,13 @@ static irqreturn_t dw_spi_transfer_handler(struct dw_spi *dws)
 			dw_spi_mask_intr(dws, DW_SPI_INT_TXEI);
 	}
 
-	return IRQ_HANDLED;
+	if (spi_controller_is_target(dws->ctlr) || !dws->rx_len || !dws->tx_len ||
+		!spi_get_csgpiod(dws->ctlr->cur_msg->spi, 0)) {
+		return IRQ_HANDLED;
+	} else {
+		dw_spi_mask_intr(dws, 0xff);
+		return IRQ_WAKE_THREAD;
+	}
 }
 
 static irqreturn_t dw_spi_enh_handler(struct dw_spi *dws)
@@ -1305,8 +1362,8 @@ int dw_spi_add_controller(struct device *dev, struct dw_spi *dws)
 	/* Basic HW init */
 	dw_spi_hw_init(dev, dws);
 
-	ret = request_irq(dws->irq, dw_spi_irq, IRQF_SHARED, dev_name(dev),
-			  ctlr);
+	ret = request_threaded_irq(dws->irq, dw_spi_irq, dw_spi_irq_thread_fn,
+				   IRQF_SHARED, dev_name(dev), ctlr);
 	if (ret < 0 && ret != -ENOTCONN) {
 		dev_err(dev, "can not request IRQ\n");
 		goto err_free_ctlr;
Signature · 1 line
2.53.0
maintainer
#6 lore raw

Re: [PATCH v4 5/5] spi: dw: use threaded interrupt and optimize the threaded ISR

Quoted 10 lines · Jisheng Zhang

To avoid blocking for an excessive amount of time, eventually impacting on system responsiveness, hard interrupt handlers should finish executing in as little time as possible.

static irqreturn_t dw_spi_transfer_handler(struct dw_spi *dws) {

drivers/spi/spi-dw-core.c +0 -0
 	u16 irq_status = dw_readl(dws, DW_SPI_ISR);
@@ -245,7 +296,13 @@ static irqreturn_t dw_spi_transfer_handler(struct dw_spi *dws)
 			dw_spi_mask_intr(dws, DW_SPI_INT_TXEI);
 	}

drivers/spi/spi-dw-core.c static irqreturn_t dw_spi_transfer_handler(struct dw_spi *dws) · line 306

Quoted 10 lines
drivers/spi/spi-dw-core.c +7 -1
 
-	return IRQ_HANDLED;
+	if (spi_controller_is_target(dws->ctlr) || !dws->rx_len || !dws->tx_len ||
+		!spi_get_csgpiod(dws->ctlr->cur_msg->spi, 0)) {
+		return IRQ_HANDLED;
+	} else {
+		dw_spi_mask_intr(dws, 0xff);
+		return IRQ_WAKE_THREAD;
+	}
 }

If we're handing a short transfer in the first interrupt then we will already have completed the transfer at the point we check have which would allow another CPU to start another transfer first. If things go very badly this might mean that the length checks look at the values from a new transfer and wake the thread. We should probably set a local flag before we complete the transfer and use that to decide if we wake the thread.