ARM: tegra: lg-x3: Add newly supported devices and fixes
Subsystems (2)
v2 cover ARM: tegra: lg-x3: Add newly supported devices and fixes
Add nodes for recently supported device (ALS, LED controllers, haptics) along with minor tweaks and fixups.
---
Changes in v2:
- added USB configuration update commit
- added p895 power LED trigger update commit
---
Svyatoslav Ryhel (9):
ARM: tegra: lg-x3: Adjust WiFi node
ARM: tegra: lg-x3: Remove pinctrl-* properties duplication
ARM: tegra: lg-x3: Lower supported suspend mode
ARM: tegra: lg-x3: Add light sensor node
ARM: tegra: lg-x3: Add flash LEDs controller node
ARM: tegra: lg-x3: Add haptic engine node
ARM: tegra: lg-x3: Add backlight LED controller node
ARM: tegra: lg-x3: Update USB configuration
ARM: tegra: p895: Update power LED trigger
arch/arm/boot/dts/nvidia/tegra30-lg-p880.dts | 5 +- arch/arm/boot/dts/nvidia/tegra30-lg-p895.dts | 7 +- arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi | 125 ++++++++++++++++++- 3 files changed, 127 insertions(+), 10 deletions(-)
Signature · 1 line
2.53.0
PATCH v2 1/9 ARM: tegra: lg-x3: Adjust WiFi node
Add missing BCM4330 compatible along with keeping fallback according to current schema. Add missing lpo clock used by the module.
--- arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-)
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +12 -1
@@ -1669,9 +1669,12 @@ sdmmc1: mmc@78000000 { /* BCM4330B1 37.4 MHz Class 1.5 ExtLNA */ wifi@1 { - compatible = "brcm,bcm4329-fmac"; + compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac"; reg = <1>; + clocks = <&ext_lpo_in>; + clock-names = "lpo"; + interrupt-parent = <&gpio>; interrupts = <TEGRA_GPIO(U, 6) IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "host-wake";
@@ -1714,6 +1717,14 @@ clk32k_in: clock-32k { clock-output-names = "pmic-oscillator"; }; + /* PMIC's 32KHz oscillator for WiFi/GPS LPO input */ + ext_lpo_in: clock-elpo-32k { + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "ext-lpo-32k-in"; + #clock-cells = <0>; + }; + gps_refclk: clock-gps { compatible = "fixed-clock"; clock-frequency = <26000000>;
Signature · 1 line
2.53.0
PATCH v2 2/9 ARM: tegra: lg-x3: Remove pinctrl-* properties duplication
In reply to Svyatoslav RyhelThe pinctrl-names and pinctrl-0 are defined in the common device tree, having them in the individual trees is redundant. Remove them.
--- arch/arm/boot/dts/nvidia/tegra30-lg-p880.dts | 3 --- arch/arm/boot/dts/nvidia/tegra30-lg-p895.dts | 3 --- 2 files changed, 6 deletions(-)
arch/arm/boot/dts/nvidia/tegra30-lg-p880.dts +0 -3
@@ -25,9 +25,6 @@ ports { }; pinmux@70000868 { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - state_default: pinmux { /* WLAN SDIO pinmux */ host-wlan-wake {
arch/arm/boot/dts/nvidia/tegra30-lg-p895.dts +0 -3
@@ -8,9 +8,6 @@ / { compatible = "lg,p895", "nvidia,tegra30"; pinmux@70000868 { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - state_default: pinmux { /* GNSS UART-B pinmux */ uartb-cts-rxd {
Signature · 1 line
2.53.0
PATCH v2 3/9 ARM: tegra: lg-x3: Lower supported suspend mode
In reply to Svyatoslav RyhelLG P880 and P895 are perfectly capable of supporting the lowest suspend mode currently available for Tegra devices which is LP1.
--- arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +1 -1
@@ -1610,7 +1610,7 @@ bridge_output: endpoint { pmc@7000e400 { status = "okay"; nvidia,invert-interrupt; - nvidia,suspend-mode = <2>; + nvidia,suspend-mode = <1>; nvidia,cpu-pwr-good-time = <2000>; nvidia,cpu-pwr-off-time = <200>; nvidia,core-pwr-good-time = <3845 3845>;
Signature · 1 line
2.53.0
PATCH v2 4/9 ARM: tegra: lg-x3: Add light sensor node
In reply to Svyatoslav RyhelAdd node for Avago APDS9900 ambient light and proximity sensor used in this device.
--- arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi | 13 +++++++++++++ 1 file changed, 13 insertions(+)
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +13 -0
@@ -1106,6 +1106,19 @@ nfc@28 { firmware-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>; }; + light-sensor@39 { + compatible = "avago,apds9900"; + reg = <0x39>; + + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(K, 2) IRQ_TYPE_EDGE_RISING>; + + vdd-supply = <&vdd_3v0_proxi>; + vddio-supply = <&vdd_1v8_sen>; + + led-max-microamp = <100000>; + }; + imu@68 { compatible = "invensense,mpu6050"; reg = <0x68>;
Signature · 1 line
2.53.0
[email protected]
AI reviewRe: [PATCH v2 4/9] ARM: tegra: lg-x3: Add light sensor node
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider: - [Low] arm: dt: incorrect interrupt trigger polarity for APDS9900 sensor --
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Low] arm: dt: incorrect interrupt trigger polarity for APDS9900 sensor --
commit 9cb1ebe47a901b15c3fac941849ede08f1799d2f
Author: Svyatoslav Ryhel <[email protected]>
ARM: tegra: lg-x3: Add light sensor node
This commit adds the device tree node for the Avago APDS9900 ambient light and proximity sensor to the tegra30-lg-x3 dtsi file.
Quoted 4 lines
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +0
-0
[ ... ]
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi nfc@28 { · line 1114
Quoted 10 lines
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +6
-0@@ -1106,6 +1106,19 @@ nfc@28 { firmware-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>; }; + light-sensor@39 { + compatible = "avago,apds9900"; + reg = <0x39>; + + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(K, 2) IRQ_TYPE_EDGE_RISING>;
[Severity: Low]
Is IRQ_TYPE_EDGE_RISING the correct interrupt polarity for this sensor?
The device tree describes the APDS9900 interrupt as IRQ_TYPE_EDGE_RISING, but the APDS9900 has an active-low open-drain interrupt pin, meaning it asserts via a falling edge or low level. This appears to be a mismatch between the DT hardware description and physical hardware.
While the Linux tsl2772 driver currently hardcodes IRQF_TRIGGER_FALLING (masking the issue in Linux), could this latent hardware description bug break interrupt handling for any OS or future driver refactoring that relies on the DT-provided flags? Booting an OS that relies on the DT interrupt trigger flags will configure the GPIO interrupt for a rising edge, which will fail to trigger when the sensor pulls the line low.
Quoted 7 lines
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +7
-0+ + vdd-supply = <&vdd_3v0_proxi>; + vddio-supply = <&vdd_1v8_sen>; + + led-max-microamp = <100000>; + }; +
Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=4
PATCH v2 5/9 ARM: tegra: lg-x3: Add flash LEDs controller node
In reply to Svyatoslav RyhelAdd node for TI LM3559 LEDs controlled used with flash LEDs in this device.
--- arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi | 30 +++++++++++++++++++++ 1 file changed, 30 insertions(+)
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +30 -0
@@ -1233,6 +1233,7 @@ rear-camera@10 { rotation = <90>; nvmem = <&m24c08>; + flash-leds = <&lm3559_led0>, <&lm3559_led1>; lens-focus = <&dw9714>; assigned-clocks = <&tegra_car TEGRA30_CLK_VI_SENSOR>,
@@ -1267,6 +1268,35 @@ m24c08: eeprom@50 { vcc-supply = <&vio_1v8_rear>; }; + led-controller@53 { + compatible = "ti,lm3559"; + reg = <0x53>; + + enable-gpios = <&gpio TEGRA_GPIO(BB, 3) GPIO_ACTIVE_HIGH>; + vin-supply = <&vdd_3v3_vbat>; + + flash-max-timeout-us = <1024000>; + ti,peak-current-microamp = <1400000>; + + #address-cells = <1>; + #size-cells = <0>; + + /* single flash led is on 2 lines */ + lm3559_led0: led@0 { + reg = <0>; + + flash-max-microamp = <393750>; + led-max-microamp = <140625>; + }; + + lm3559_led1: led@1 { + reg = <1>; + + flash-max-microamp = <393750>; + led-max-microamp = <140625>; + }; + }; + camera-pmic@7d { compatible = "ti,lp8720"; reg = <0x7d>;
Signature · 1 line
2.53.0
[email protected]
AI reviewRe: [PATCH v2 5/9] ARM: tegra: lg-x3: Add flash LEDs controller node
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider: - [Medium] dt-bindings: inaccurate modeling of single physical flash LED as two nodes --
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Medium] dt-bindings: inaccurate modeling of single physical flash LED as two nodes --
commit a769a0c3851e51b75e86359c4dd2c87f24520282
Author: Svyatoslav Ryhel <[email protected]>
ARM: tegra: lg-x3: Add flash LEDs controller node
This commit adds a device tree node for the TI LM3559 LED controller used for the flash LEDs in the LG X3 device. It also hooks up the new LED nodes to the rear camera flash properties.
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi rear-camera@10 { · line 1236
Quoted 9 lines
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +1
-0@@ -1233,6 +1233,7 @@ rear-camera@10 { rotation = <90>; nvmem = <&m24c08>; + flash-leds = <&lm3559_led0>, <&lm3559_led1>;
[Severity: Medium]
Does linking two separate flash nodes here force user-space applications to coordinate both to achieve the intended brightness?
The V4L2 framework will expose two separate flash subdevices for a single physical LED. Any user-space app using the camera flash will encounter this quirk.
Quoted 3 lines
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +0
-0lens-focus = <&dw9714>; assigned-clocks = <&tegra_car TEGRA30_CLK_VI_SENSOR>,
[ ... ]
Quoted 10 lines
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +6
-0@@ -1267,6 +1268,35 @@ m24c08: eeprom@50 { vcc-supply = <&vio_1v8_rear>; }; + led-controller@53 { + compatible = "ti,lm3559"; + reg = <0x53>; + + enable-gpios = <&gpio TEGRA_GPIO(BB, 3) GPIO_ACTIVE_HIGH>; + vin-supply = <&vdd_3v3_vbat>;
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi m24c08: eeprom@50 { · line 1286
Quoted 10 lines
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +10
-0+ + flash-max-timeout-us = <1024000>; + ti,peak-current-microamp = <1400000>; + + #address-cells = <1>; + #size-cells = <0>; + + /* single flash led is on 2 lines */ + lm3559_led0: led@0 { + reg = <0>;
[Severity: Medium]
Does modeling this as two distinct logical LED nodes inaccurately describe the physical hardware?
The comment explicitly acknowledges the hardware topology is one physical LED connected to two output lines. Device Tree principles dictate that the DT must accurately describe the physical hardware structure.
Should a single physical LED be modeled as a single node with led-sources = <0 1>; instead of two separate nodes? While the lm3560 driver may currently lack support for led-sources, modeling hardware based on software driver limitations is generally discouraged.
Quoted 12 lines
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +12
-0+ + flash-max-microamp = <393750>; + led-max-microamp = <140625>; + }; + + lm3559_led1: led@1 { + reg = <1>; + + flash-max-microamp = <393750>; + led-max-microamp = <140625>; + }; + };
Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=5
PATCH v2 6/9 ARM: tegra: lg-x3: Add haptic engine node
In reply to Svyatoslav RyhelAdd node for Imagis ISA1200 haptic motor driver used in this device.
--- arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi | 24 +++++++++++++++++++++ 1 file changed, 24 insertions(+)
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +24 -0
@@ -1568,6 +1568,30 @@ power-sensor@40 { vs-supply = <&vdd_3v0_sen>; }; + haptic-engine@49 { + compatible = "imagis,isa1200"; + reg = <0x49>; + + control-gpios = <&gpio TEGRA_GPIO(H, 1) GPIO_ACTIVE_HIGH>; + + pwms = <&pwm 3 53000>; + + vdd-supply = <&vdd_3v3_vbat>; + vddp-supply = <&vdd_1v8_vio>; + + imagis,clk-div = <128>; + imagis,pll-div = <1>; + + imagis,mode = <0>; /* LRA_MODE */ + imagis,duty-cycle-ns = <1250>; + + ldo { + regulator-name = "vdd_vib"; + regulator-min-microvolt = <2300000>; + regulator-max-microvolt = <2300000>; + }; + }; + nct72: temperature-sensor@4c { compatible = "onnn,nct1008"; reg = <0x4c>;
Signature · 1 line
2.53.0
PATCH v2 7/9 ARM: tegra: lg-x3: Add backlight LED controller node
In reply to Svyatoslav RyhelAdd node for TI LM3533 LED controller used in this device for panel backlight.
--- arch/arm/boot/dts/nvidia/tegra30-lg-p880.dts | 2 ++ arch/arm/boot/dts/nvidia/tegra30-lg-p895.dts | 2 ++ arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi | 24 ++++++++++++++++++++ 3 files changed, 28 insertions(+)
arch/arm/boot/dts/nvidia/tegra30-lg-p880.dts +2 -0
@@ -155,6 +155,8 @@ panel@1 { vdd-supply = <&vcc_3v0_lcd>; vddio-supply = <&iovcc_1v8_lcd>; + backlight = <&backlight>; + port { panel_input: endpoint { remote-endpoint = <&bridge_output>;
arch/arm/boot/dts/nvidia/tegra30-lg-p895.dts +2 -0
@@ -179,6 +179,8 @@ panel@1 { vcc-supply = <&vcc_3v0_lcd>; iovcc-supply = <&iovcc_1v8_lcd>; + backlight = <&backlight>; + port { panel_input: endpoint { remote-endpoint = <&bridge_output>;
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +24 -0
@@ -1170,6 +1170,30 @@ rmi4-f11@11 { }; }; + led-controller@36 { + compatible = "ti,lm3533"; + reg = <0x36>; + + enable-gpios = <&gpio TEGRA_GPIO(N, 6) GPIO_ACTIVE_HIGH>; + vin-supply = <&vdd_3v3_vbat>; + + ti,boost-ovp-microvolt = <24000000>; + ti,boost-freq-hz = <500000>; + + #address-cells = <1>; + #size-cells = <0>; + + backlight: backlight@0 { + compatible = "ti,lm3533-backlight"; + reg = <0>; + + led-max-microamp = <23400>; + led-sources = <0 1>; + + ti,linear-mapping-mode; + }; + }; + max14526: muic@44 { compatible = "maxim,max14526"; reg = <0x44>;
Signature · 1 line
2.53.0
[email protected]
AI reviewRe: [PATCH v2 7/9] ARM: tegra: lg-x3: Add backlight LED controller node
Thank you for your contribution! Sashiko AI review found 3 potential issue(s) to consider: - [High] driver core: ti,lm3533 unconditional probe failure without platform data - [High] gpio…
Thank you for your contribution! Sashiko AI review found 3 potential issue(s) to consider:
- [High] driver core: ti,lm3533 unconditional probe failure without platform data
- [High] gpio: lm3533-core requests unnamed GPIO while DT provides enable-gpios
- [Medium] dts: tegra30-lg-x3: undocumented addition of unrelated hardware nodes --
commit ff4e61027a1ca9aeb5769dcf34e03e97e0cb0683
Author: Svyatoslav Ryhel <[email protected]>
ARM: tegra: lg-x3: Add backlight LED controller node
Add node for TI LM3533 LED controller used in this device for panel backlight.
Quoted 4 lines
ARM: tegra: lg-x3: Add backlight LED controller node
Add node for TI LM3533 LED controller used in this device for panel backlight.
[Severity: Medium]
Does this patch also silently introduce other hardware modifications, such as a light sensor (avago,apds9900), haptic engine (imagis,isa1200), camera flash LEDs (ti,lm3559), and critical power management parameters like nvidia,suspend-mode = <1>?
The commit message explicitly claims the sole purpose of the patch is to add the backlight LED controller node. Including unrelated changes hides potential regressions.
arch/arm/boot/dts/nvidia/tegra30-lg-p880.dts panel@1 { · line 159
Quoted 10 lines
arch/arm/boot/dts/nvidia/tegra30-lg-p880.dts +2
-0@@ -155,6 +155,8 @@ panel@1 { vdd-supply = <&vcc_3v0_lcd>; vddio-supply = <&iovcc_1v8_lcd>; + backlight = <&backlight>; +
[Severity: High]
Since the lm3533-core.c driver lacks Device Tree parsing and explicitly requires platform data, won't lm3533_device_init() immediately fail with -EINVAL?
drivers/mfd/lm3533-core.c:lm3533_device_init() {
...
if (!pdata) {
dev_err(lm3533->dev, "no platform data\n");
return -EINVAL;
}
...
}Because the backlight device never registers, will the panel driver indefinitely wait for it via drm_panel_of_backlight(), returning -EPROBE_DEFER and permanently breaking the primary display initialization?
[ ... ]
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi rmi4-f11@11 { · line 1177
Quoted 13 lines
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +5
-0@@ -1170,6 +1170,30 @@ rmi4-f11@11 { }; }; + led-controller@36 { + compatible = "ti,lm3533"; + reg = <0x36>; + + enable-gpios = <&gpio TEGRA_GPIO(N, 6) GPIO_ACTIVE_HIGH>;
[Severity: High]
The device tree node specifies enable-gpios, but the driver acquires the GPIO using a NULL connection ID:
drivers/mfd/lm3533-core.c:lm3533_device_init() {
...
lm3533->hwen = devm_gpiod_get(lm3533->dev, NULL, GPIOD_OUT_LOW);
...
}With a NULL con_id, the GPIO subsystem only searches for properties named 'gpios' or 'gpio'. Will this fail to match 'enable-gpios' and cause the driver to fail probe with -ENOENT?
Quoted 19 lines
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +19
-0+ vin-supply = <&vdd_3v3_vbat>; + + ti,boost-ovp-microvolt = <24000000>; + ti,boost-freq-hz = <500000>; + + #address-cells = <1>; + #size-cells = <0>; + + backlight: backlight@0 { + compatible = "ti,lm3533-backlight"; + reg = <0>; + + led-max-microamp = <23400>; + led-sources = <0 1>; + + ti,linear-mapping-mode; + }; + }; +
Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=7
PATCH v2 8/9 ARM: tegra: lg-x3: Update USB configuration
In reply to Svyatoslav RyhelUpdate USB controller configuration and link it to MUIC.
--- arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi | 19 ++++++++++++++++++- 1 file changed, 18 insertions(+), 1 deletion(-)
arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi +18 -1
@@ -1215,6 +1215,11 @@ muic_to_charger: endpoint@0 { reg = <0>; remote-endpoint = <&charger_input>; }; + + muic_to_usb: endpoint@1 { + reg = <1>; + remote-endpoint = <&usb_input>; + }; }; };
@@ -1788,7 +1793,19 @@ usb@7d000000 { compatible = "nvidia,tegra30-udc"; status = "okay"; dr_mode = "otg"; - extcon = <&max14526>, <&max14526>; + + hnp-disable; + srp-disable; + adp-disable; + + usb-role-switch; + extcon = <&max14526>, <&max14526>; /* vbus, id */ + + port { + usb_input: endpoint { + remote-endpoint = <&muic_to_usb>; + }; + }; }; usb-phy@7d000000 {
Signature · 1 line
2.53.0
PATCH v2 9/9 ARM: tegra: p895: Update power LED trigger
In reply to Svyatoslav RyhelThe previous "battery-charging" trigger was unreliable and slow to update. Since LG X3 devices now have a charger driver, use "max8971-charger-online" instead. Tested on the LG Optimus Vu P895; it works much more reliably.
--- arch/arm/boot/dts/nvidia/tegra30-lg-p895.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/nvidia/tegra30-lg-p895.dts +1 -1
@@ -552,7 +552,7 @@ led-power { label = "power::white"; gpios = <&gpio TEGRA_GPIO(R, 3) GPIO_ACTIVE_HIGH>; - linux,default-trigger = "battery-charging"; + linux,default-trigger = "max8971-charger-online"; color = <LED_COLOR_ID_WHITE>; function = LED_FUNCTION_CHARGING;
Signature · 1 line
2.53.0
нд, 4 жовт. 2026 р. о 18:45 Svyatoslav Ryhel <[email protected]> пише:
Quoted 21 lines
Add nodes for recently supported device (ALS, LED controllers, haptics) along with minor tweaks and fixups.
---
Changes in v2:
- added USB configuration update commit
- added p895 power LED trigger update commit
---Svyatoslav Ryhel (9):
ARM: tegra: lg-x3: Adjust WiFi node
ARM: tegra: lg-x3: Remove pinctrl-* properties duplication
ARM: tegra: lg-x3: Lower supported suspend mode
ARM: tegra: lg-x3: Add light sensor node
ARM: tegra: lg-x3: Add flash LEDs controller node
ARM: tegra: lg-x3: Add haptic engine node
ARM: tegra: lg-x3: Add backlight LED controller node
ARM: tegra: lg-x3: Update USB configuration
ARM: tegra: p895: Update power LED trigger
Quoted 8 lines
arch/arm/boot/dts/nvidia/tegra30-lg-p880.dts | 5 +- arch/arm/boot/dts/nvidia/tegra30-lg-p895.dts | 7 +- arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi | 125 ++++++++++++++++++- 3 files changed, 127 insertions(+), 10 deletions(-)--
2.53.0
Hello Thierry!
May you please pick this patch set if you are ok with it? Thank you!
пн, 12 жовт. 2026 р. о 13:55 Svyatoslav Ryhel <[email protected]> пише:
Quoted 28 lines
нд, 4 жовт. 2026 р. о 18:45 Svyatoslav Ryhel <[email protected]> пише:
Quoted 26 lines
Add nodes for recently supported device (ALS, LED controllers, haptics) along with minor tweaks and fixups.
---
Changes in v2:
- added USB configuration update commit
- added p895 power LED trigger update commit
---Svyatoslav Ryhel (9):
ARM: tegra: lg-x3: Adjust WiFi node
ARM: tegra: lg-x3: Remove pinctrl-* properties duplication
ARM: tegra: lg-x3: Lower supported suspend mode
ARM: tegra: lg-x3: Add light sensor node
ARM: tegra: lg-x3: Add flash LEDs controller node
ARM: tegra: lg-x3: Add haptic engine node
ARM: tegra: lg-x3: Add backlight LED controller node
ARM: tegra: lg-x3: Update USB configuration
ARM: tegra: p895: Update power LED triggerarch/arm/boot/dts/nvidia/tegra30-lg-p880.dts | 5 +- arch/arm/boot/dts/nvidia/tegra30-lg-p895.dts | 7 +- arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi | 125 ++++++++++++++++++- 3 files changed, 127 insertions(+), 10 deletions(-)
Quoted 7 lines
Quoted 3 lines
--
2.53.0Hello Thierry!
May you please pick this patch set if you are ok with it? Thank you!
Oh, you already did. Apologies!
Thierry Reding
maintainerQuoted 33 lines · Svyatoslav Ryhel
пн, 12 жовт. 2026 р. о 13:55 Svyatoslav Ryhel <[email protected]> пише:
Quoted 32 lines
нд, 4 жовт. 2026 р. о 18:45 Svyatoslav Ryhel <[email protected]> пише:
Quoted 29 lines
Add nodes for recently supported device (ALS, LED controllers, haptics) along with minor tweaks and fixups.
---
Changes in v2:
- added USB configuration update commit
- added p895 power LED trigger update commit
---Svyatoslav Ryhel (9):
ARM: tegra: lg-x3: Adjust WiFi node
ARM: tegra: lg-x3: Remove pinctrl-* properties duplication
ARM: tegra: lg-x3: Lower supported suspend mode
ARM: tegra: lg-x3: Add light sensor node
ARM: tegra: lg-x3: Add flash LEDs controller node
ARM: tegra: lg-x3: Add haptic engine node
ARM: tegra: lg-x3: Add backlight LED controller node
ARM: tegra: lg-x3: Update USB configuration
ARM: tegra: p895: Update power LED triggerarch/arm/boot/dts/nvidia/tegra30-lg-p880.dts | 5 +- arch/arm/boot/dts/nvidia/tegra30-lg-p895.dts | 7 +- arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi | 125 ++++++++++++++++++- 3 files changed, 127 insertions(+), 10 deletions(-)--
2.53.0
Quoted 5 lines
Quoted 3 lines
Hello Thierry!
May you please pick this patch set if you are ok with it? Thank you!Oh, you already did. Apologies!
I picked up version 1. This v2 came in too late. Pull requests go out before -rc6, which in this case was v7.3-rc6, released on October 4.
Looks like only the last two patches were added in v2, with no other changes to the other patches, so I can pick up the last two after the merge window closes. If you don't hear from me after the first week after v7.4-rc1, you may want to resend the last two patches again.
Thierry
вт, 13 жовт. 2026 р. о 19:16 Thierry Reding <[email protected]> пише:
Quoted 41 lines · Svyatoslav Ryhel
Quoted 33 lines
пн, 12 жовт. 2026 р. о 13:55 Svyatoslav Ryhel <[email protected]> пише:
Quoted 32 lines
нд, 4 жовт. 2026 р. о 18:45 Svyatoslav Ryhel <[email protected]> пише:
Quoted 29 lines
Add nodes for recently supported device (ALS, LED controllers, haptics) along with minor tweaks and fixups.
---
Changes in v2:
- added USB configuration update commit
- added p895 power LED trigger update commit
---Svyatoslav Ryhel (9):
ARM: tegra: lg-x3: Adjust WiFi node
ARM: tegra: lg-x3: Remove pinctrl-* properties duplication
ARM: tegra: lg-x3: Lower supported suspend mode
ARM: tegra: lg-x3: Add light sensor node
ARM: tegra: lg-x3: Add flash LEDs controller node
ARM: tegra: lg-x3: Add haptic engine node
ARM: tegra: lg-x3: Add backlight LED controller node
ARM: tegra: lg-x3: Update USB configuration
ARM: tegra: p895: Update power LED triggerarch/arm/boot/dts/nvidia/tegra30-lg-p880.dts | 5 +- arch/arm/boot/dts/nvidia/tegra30-lg-p895.dts | 7 +- arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi | 125 ++++++++++++++++++- 3 files changed, 127 insertions(+), 10 deletions(-)--
2.53.0Quoted 5 lines
Quoted 3 lines
Hello Thierry!
May you please pick this patch set if you are ok with it? Thank you!Oh, you already did. Apologies!
Quoted 8 lines
I picked up version 1. This v2 came in too late. Pull requests go out before -rc6, which in this case was v7.3-rc6, released on October 4.
Looks like only the last two patches were added in v2, with no other changes to the other patches, so I can pick up the last two after the merge window closes. If you don't hear from me after the first week after v7.4-rc1, you may want to resend the last two patches again.
That is correct, v2 has only those 2 patches added. If you don't mind, I will include those 2 patches in a different patch set, you don't have to worry about them in this patch sequence.
Quoted 1 line
Thierry