Skip to contentSkip to conversation

iio: chemical: ccs811: Make sampling frequency configurable

PATCH Superseded Nikhil Gautam 2 participants 2 messages Oct 25 IIO

v3 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 iio: chemical: ccs811: Make sampling frequency configurable

Allow userspace to configure the CCS811 IAQ measurement rate through the IIO sampling_frequency attribute.

Support the three IAQ measurement modes with sampling frequencies of 1 Hz, 0.1 Hz, and approximately 0.016667 Hz, corresponding to measurement intervals of 1, 10, and 60 seconds.

Preserve unrelated bits in the MEAS_MODE register when updating the drive mode, and cache the selected mode after a successful register write. Expose the supported frequencies through sampling_frequency_available.

Changes in v3:
- Reuse the sampling frequency array instead of duplicating frequency values.
- Separate register updates from locking and wakeup handling.
- Use a separate variable for the updated MEAS_MODE register value.
- Simplify the sampling frequency getter.
- Mark the completed drive-mode configuration TODO as done.

Changes in v2:
- Fix the Clang build error caused by guard() in the switch statement.

---
 drivers/iio/chemical/ccs811.c | 148 ++++++++++++++++++++++++++++++++--
 1 file changed, 142 insertions(+), 6 deletions(-)
drivers/iio/chemical/ccs811.c +142 -6
index d126ee12ffe5..c48ac37b32be 100644
@@ -9,7 +9,7 @@
  * IIO driver for AMS CCS811 (I2C address 0x5A/0x5B set by ADDR Low/High)
  *
  * TODO:
- * 1. Make the drive mode selectable form userspace
+ * 1. DONE. Was: "Make the drive mode selectable form userspace"
  * 2. Add support for interrupts
  * 3. Adjust time to wait for data to be ready based on selected operation mode
  * 4. Read error register and put the information in logs
@@ -54,6 +54,7 @@
 #define CCS811_STATUS_FW_MODE_APPLICATION	BIT(7)
 
 /* Measurement modes */
+#define CCS811_MODE_MASK	GENMASK(6, 4)
 #define CCS811_MODE_IDLE	0x00
 #define CCS811_MODE_IAQ_1SEC	0x10
 #define CCS811_MODE_IAQ_10SEC	0x20
@@ -79,6 +80,7 @@ struct ccs811_data {
 	struct iio_trigger *drdy_trig;
 	struct gpio_desc *wakeup_gpio;
 	bool drdy_trig_on;
+	u8 drive_mode;
 	/* Ensures correct alignment of timestamp if present */
 	struct {
 		s16 channels[2];
@@ -86,6 +88,12 @@ struct ccs811_data {
 	} scan;
 };
 
+static const int ccs811_samp_freq[] = {
+	1, 0,
+	0, 100000,
+	0, 16667,
+};
+
 static const struct iio_chan_spec ccs811_channels[] = {
 	{
 		.type = IIO_CURRENT,
@@ -103,6 +111,8 @@ static const struct iio_chan_spec ccs811_channels[] = {
 		.modified = 1,
 		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
 				      BIT(IIO_CHAN_INFO_SCALE),
+		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+		.info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SAMP_FREQ),
 		.scan_index = 0,
 		.scan_type = {
 			.sign = 'u',
@@ -163,16 +173,21 @@ static int ccs811_start_sensor_application(struct i2c_client *client)
 	return 0;
 }
 
-static int ccs811_setup(struct i2c_client *client)
+static int ccs811_setup(struct ccs811_data *data)
 {
 	int ret;
 
-	ret = ccs811_start_sensor_application(client);
+	ret = ccs811_start_sensor_application(data->client);
+	if (ret < 0)
+		return ret;
+
+	ret = i2c_smbus_write_byte_data(data->client, CCS811_MEAS_MODE,
+					CCS811_MODE_IAQ_1SEC);
 	if (ret < 0)
 		return ret;
 
-	return i2c_smbus_write_byte_data(client, CCS811_MEAS_MODE,
-					 CCS811_MODE_IAQ_1SEC);
+	data->drive_mode = CCS811_MODE_IAQ_1SEC;
+	return 0;
 }
 
 static void ccs811_set_wakeup(struct ccs811_data *data, bool enable)
@@ -188,6 +203,52 @@ static void ccs811_set_wakeup(struct ccs811_data *data, bool enable)
 		usleep_range(20, 30);
 }
 
+static int ccs811_update_sampling_freq(struct ccs811_data *data,
+				       int val, int val2)
+{
+	u8 drive_mode;
+	u8 mode;
+	int ret;
+
+	if (val == ccs811_samp_freq[0] && val2 == ccs811_samp_freq[1])
+		drive_mode = CCS811_MODE_IAQ_1SEC;
+	else if (val == ccs811_samp_freq[2] && val2 == ccs811_samp_freq[3])
+		drive_mode = CCS811_MODE_IAQ_10SEC;
+	else if (val == ccs811_samp_freq[4] && val2 == ccs811_samp_freq[5])
+		drive_mode = CCS811_MODE_IAQ_60SEC;
+	else
+		return -EINVAL;
+
+	ret = i2c_smbus_read_byte_data(data->client, CCS811_MEAS_MODE);
+	if (ret < 0)
+		return ret;
+
+	mode = (ret & ~CCS811_MODE_MASK) | drive_mode;
+
+	ret = i2c_smbus_write_byte_data(data->client, CCS811_MEAS_MODE,
+					mode);
+	if (ret < 0)
+		return ret;
+
+	data->drive_mode = drive_mode;
+
+	return 0;
+}
+
+static int ccs811_set_sampling_freq(struct ccs811_data *data,
+				    int val, int val2)
+{
+	int ret;
+
+	guard(mutex)(&data->lock);
+
+	ccs811_set_wakeup(data, true);
+	ret = ccs811_update_sampling_freq(data, val, val2);
+	ccs811_set_wakeup(data, false);
+
+	return ret;
+}
+
 static int ccs811_get_measurement(struct ccs811_data *data)
 {
 	int ret, tries = 11;
@@ -215,6 +276,29 @@ static int ccs811_get_measurement(struct ccs811_data *data)
 	return ret;
 }
 
+static int ccs811_get_sampling_freq(struct ccs811_data *data,
+				    int *val, int *val2)
+{
+	guard(mutex)(&data->lock);
+
+	switch (data->drive_mode) {
+	case CCS811_MODE_IAQ_1SEC:
+		*val = ccs811_samp_freq[0];
+		*val2 = ccs811_samp_freq[1];
+		return IIO_VAL_INT_PLUS_MICRO;
+	case CCS811_MODE_IAQ_10SEC:
+		*val = ccs811_samp_freq[2];
+		*val2 = ccs811_samp_freq[3];
+		return IIO_VAL_INT_PLUS_MICRO;
+	case CCS811_MODE_IAQ_60SEC:
+		*val = ccs811_samp_freq[4];
+		*val2 = ccs811_samp_freq[5];
+		return IIO_VAL_INT_PLUS_MICRO;
+	default:
+		return -EINVAL;
+	}
+}
+
 static int ccs811_read_info_raw(struct ccs811_data *data,
 				struct iio_chan_spec const *chan,
 				int *val, int mask)
@@ -249,6 +333,28 @@ static int ccs811_read_info_raw(struct ccs811_data *data,
 	}
 }
 
+static int ccs811_write_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int val, int val2, long mask)
+{
+	struct ccs811_data *data = iio_priv(indio_dev);
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		if (!iio_device_claim_direct(indio_dev))
+			return -EBUSY;
+
+		ret = ccs811_set_sampling_freq(data, val, val2);
+
+		iio_device_release_direct(indio_dev);
+		return ret;
+
+	default:
+		return -EINVAL;
+	}
+}
+
 static int ccs811_read_raw(struct iio_dev *indio_dev,
 			   struct iio_chan_spec const *chan,
 			   int *val, int *val2, long mask)
@@ -293,13 +399,43 @@ static int ccs811_read_raw(struct iio_dev *indio_dev,
 		default:
 			return -EINVAL;
 		}
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		return ccs811_get_sampling_freq(data, val, val2);
 	default:
 		return -EINVAL;
 	}
 }
 
+static int ccs811_read_avail(struct iio_dev *indio_dev,
+			     struct iio_chan_spec const *chan,
+			     const int **vals, int *type, int *length,
+			     long mask)
+{
+	if (mask != IIO_CHAN_INFO_SAMP_FREQ)
+		return -EINVAL;
+
+	*vals = ccs811_samp_freq;
+	*type = IIO_VAL_INT_PLUS_MICRO;
+	*length = ARRAY_SIZE(ccs811_samp_freq);
+
+	return IIO_AVAIL_LIST;
+}
+
+static int ccs811_write_raw_get_fmt(struct iio_dev *indio_dev,
+				    struct iio_chan_spec const *chan,
+				    long mask)
+{
+	if (mask == IIO_CHAN_INFO_SAMP_FREQ)
+		return IIO_VAL_INT_PLUS_MICRO;
+
+	return -EINVAL;
+}
+
 static const struct iio_info ccs811_info = {
 	.read_raw = ccs811_read_raw,
+	.write_raw = ccs811_write_raw,
+	.read_avail = ccs811_read_avail,
+	.write_raw_get_fmt = ccs811_write_raw_get_fmt,
 };
 
 static int ccs811_set_trigger_state(struct iio_trigger *trig,
@@ -460,7 +596,7 @@ static int ccs811_probe(struct i2c_client *client)
 		return -ENODEV;
 	}
 
-	ret = ccs811_setup(client);
+	ret = ccs811_setup(data);
 	if (ret < 0) {
 		ccs811_set_wakeup(data, false);
 		return ret;
Signature · 1 line
2.39.5
#1 lore raw
Quoted 7 lines · Nikhil Gautam

Allow userspace to configure the CCS811 IAQ measurement rate through the IIO sampling_frequency attribute.

Support the three IAQ measurement modes with sampling frequencies of 1 Hz, 0.1 Hz, and approximately 0.016667 Hz, corresponding to measurement intervals of 1, 10, and 60 seconds.

Quoted 6 lines

Preserve unrelated bits in the MEAS_MODE register when updating the drive mode, and cache the selected mode after a successful register write. Expose the supported frequencies through sampling_frequency_available.

The cutter is missing here, we don't want to see changelog in the commit messages and moreover this contribution is not strictly signed-off, as the tag block is the last in the commit message. This is a show-stopper to take the patch, even if it's desired and correct.

Quoted 11 lines

Changes in v3:
- Reuse the sampling frequency array instead of duplicating frequency values.
- Separate register updates from locking and wakeup handling.
- Use a separate variable for the updated MEAS_MODE register value.
- Simplify the sampling frequency getter.
- Mark the completed drive-mode configuration TODO as done.

Changes in v2:
- Fix the Clang build error caused by guard() in the switch statement.
---

...

drivers/iio/chemical/ccs811.c struct ccs811_data { · line 95

Quoted 5 lines
drivers/iio/chemical/ccs811.c +5 -0
+static const int ccs811_samp_freq[] = {
+	1, 0,
+	0, 100000,
+	0, 16667,
+};

Make it double dimension array instead. Each index can be named as CCS811_MODE_IAQ_1SEC and so on, while the shift is applied later on.

With the above being done, the code can use either a for-loop or simple indexing.

*Yes, I see that the value(s) can be used directly in the code, but try to explore an approach that can improve robustness and readability of the code.

...

drivers/iio/chemical/ccs811.c static int ccs811_read_info_raw(struct ccs811_data *data, · line 346

Quoted 8 lines
drivers/iio/chemical/ccs811.c +8 -0
+{
+	struct ccs811_data *data = iio_priv(indio_dev);
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		if (!iio_device_claim_direct(indio_dev))
+			return -EBUSY;

Can we use IIO_DEV_ACQUIRE_DIRECT_MODE() here?

Quoted 9 lines
drivers/iio/chemical/ccs811.c +9 -0
+		ret = ccs811_set_sampling_freq(data, val, val2);
+
+		iio_device_release_direct(indio_dev);
+		return ret;
+
+	default:
+		return -EINVAL;
+	}
+}
Signature · 2 lines
With Best Regards,
Andy Shevchenko