Skip to contentSkip to conversation

drm/nouveau/nvkm: clear use.enabled when subdev init fails

PATCH In review Rosen Penev 2 participants 2 messages Nov 1 – Nov 5

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 drm/nouveau/nvkm: clear use.enabled when subdev init fails

On Kepler boards without the video decode falcon firmware installed (msvld/mspdec/msppp), every other VA-API decode attempt binds to an engine with no ucode loaded. The submitted work never completes, which leads to a context switch timeout, a channel recovery that cannot reset the engine, and eviction waits on fences that never signal. The process ends up stuck in D state, or killed by SIGBUS when it touches a buffer evicted after the wait times out:

msvld: unable to load firmware data
msvld: init failed, -19
fifo: SCHED_ERROR 0a [CTXSW_TIMEOUT]
vo[5444]: channel 14 killed!

  WARNING: drivers/gpu/drm/nouveau/nvkm/engine/fifo/runl.c:117 at nvkm_runl_rc+0x2a4/0x3b0 [nouveau]
  [TTM] Buffer eviction failed
  WARNING: drivers/gpu/drm/nouveau/nouveau_bo.c:1092 at nouveau_bo_move_ntfy.part.0+0x9b/0x100 [nouveau]

Tracing nvkm_subdev_ref() and nvkm_subdev_init_() shows the pattern:
a reference taken with enabled=0 runs nvkm_falcon_init(), which returns -ENODEV; the next reference sees enabled=1 and succeeds without running it.

Clear use.enabled when init() fails, so that every later reference retries init and fails cleanly. The other readers of use.enabled are fini() handlers that use it to skip teardown, which they now also do after a failed init().

On a GK107 (Quadro K1100M) without video firmware, playing H.264 with mpv --hwdec=auto: without this patch the GPU channel is killed within a minute and mpv hangs; with it, VA-API decoder creation fails, mpv falls back to software decoding, and no faults are logged.

Fixes 8478cd5a740a ("drm/nouveau/nvkm: add locking to subdev/engine init paths")
---
 drivers/gpu/drm/nouveau/nvkm/core/subdev.c | 1 +
 1 file changed, 1 insertion(+)
drivers/gpu/drm/nouveau/nvkm/core/subdev.c +1 -0
index aab5a73f467a..ff6858f5e5d3 100644
@@ -157,6 +157,7 @@ nvkm_subdev_init_(struct nvkm_subdev *subdev)
 		ret = subdev->func->init(subdev);
 		if (ret) {
 			nvkm_error(subdev, "init failed, %d\n", ret);
+			subdev->use.enabled = false;
 			return ret;
 		}
 	}
Signature · 1 line
2.56.0
maintainer
#1 lore raw
Quoted 27 lines · Rosen Penev

On Kepler boards without the video decode falcon firmware installed (msvld/mspdec/msppp), every other VA-API decode attempt binds to an engine with no ucode loaded. The submitted work never completes, which leads to a context switch timeout, a channel recovery that cannot reset the engine, and eviction waits on fences that never signal. The process ends up stuck in D state, or killed by SIGBUS when it touches a buffer evicted after the wait times out:

msvld: unable to load firmware data
msvld: init failed, -19
fifo: SCHED_ERROR 0a [CTXSW_TIMEOUT]
vo[5444]: channel 14 killed!

  WARNING: drivers/gpu/drm/nouveau/nvkm/engine/fifo/runl.c:117 at nvkm_runl_rc+0x2a4/0x3b0 [nouveau]
  [TTM] Buffer eviction failed
  WARNING: drivers/gpu/drm/nouveau/nouveau_bo.c:1092 at nouveau_bo_move_ntfy.part.0+0x9b/0x100 [nouveau]

Tracing nvkm_subdev_ref() and nvkm_subdev_init_() shows the pattern:
a reference taken with enabled=0 runs nvkm_falcon_init(), which returns -ENODEV; the next reference sees enabled=1 and succeeds without running it.

Clear use.enabled when init() fails, so that every later reference retries init and fails cleanly. The other readers of use.enabled are fini() handlers that use it to skip teardown, which they now also do after a failed init().

Quoted 4 lines

On a GK107 (Quadro K1100M) without video firmware, playing H.264 with mpv --hwdec=auto: without this patch the GPU channel is killed within a minute and mpv hangs; with it, VA-API decoder creation fails, mpv falls back to software decoding, and no faults are logged.

Appled to drm-misc-fixes.

Thanks,
Dave.