an8855: add MFD driver

Add support for Airoha AN8855 Switch that provide support for a DSA switch and a NVMEM provider.

Also make use of the mdio-regmap driver and register a regmap for each internal PHY of the switch.
This is needed to handle the double usage of the PHYs as both PHY and Switch accessor.

Signed-off-by Christian Marangi <[email protected]>

---
 drivers/mfd/Kconfig         |  14 +
 drivers/mfd/Makefile        |   1 +
 drivers/mfd/airoha-an8855.c | 579 ++++++++++++++++++++++++++++++++++++
 3 files changed, 594 insertions(+)
 create mode 100644 drivers/mfd/airoha-an8855.c

drivers/mfd/Kconfig +14 -0

index 87ed55c155f0..653a81435b20 100644
@@ -54,6 +54,20 @@ config MFD_ALTERA_SYSMGR
 	  using regmap_mmio accesses for ARM32 parts and SMC calls to
 	  EL3 for ARM64 parts.
 
+config MFD_AIROHA_AN8855
+	tristate "Airoha AN8855 Switch Core"
+	select MFD_CORE
+	select REGMAP
+	select PHYLIB
+	select MDIO_REGMAP
+	depends on NETDEVICES && OF
+	help
+	  Support for the Airoha AN8855 Switch Core. This is an SoC
+	  that provides various peripherals, to count, i2c, an Ethrnet
+	  Switch, a CPU timer, GPIO, eFUSE.
+
+	  Currently it provides a DSA switch and a NVMEM provider.
+
 config MFD_ACT8945A
 	tristate "Active-semi ACT8945A"
 	select MFD_CORE

drivers/mfd/Makefile +1 -0

index f8101d2a9ce9..96bbe3fad736 100644
@@ -8,6 +8,7 @@ obj-$(CONFIG_MFD_88PM860X)	+= 88pm860x.o
 obj-$(CONFIG_MFD_88PM800)	+= 88pm800.o 88pm80x.o
 obj-$(CONFIG_MFD_88PM805)	+= 88pm805.o 88pm80x.o
 obj-$(CONFIG_MFD_88PM886_PMIC)	+= 88pm886.o
+obj-$(CONFIG_MFD_AIROHA_AN8855)	+= airoha-an8855.o
 obj-$(CONFIG_MFD_ACT8945A)	+= act8945a.o
 obj-$(CONFIG_MFD_SM501)		+= sm501.o
 obj-$(CONFIG_ARCH_BCM2835)	+= bcm2835-pm.o

drivers/mfd/airoha-an8855.c new file +3 -0

new file mode 100644
index 000000000000..6a270555db5c
@@ -0,0 +1,579 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Core driver for Airoha AN8855 Switch

drivers/mfd/airoha-an8855.c new file +8 -0

+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy.h>
+#include <linux/regmap.h>
+
+/* Register for HW trap status */
+#define AN8855_HWTRAP			0x1000009c
+

drivers/mfd/airoha-an8855.c new file +37 -0

+#define AN8855_RG_GPHY_AFE_PWD		0x1028c840
+
+/* MII Registers */
+#define AN8855_PHY_SELECT_PAGE		0x1f
+#define   AN8855_PHY_PAGE		GENMASK(2, 0)
+#define   AN8855_PHY_PAGE_STANDARD	FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x0)
+#define   AN8855_PHY_PAGE_EXTENDED_1	FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x1)
+#define   AN8855_PHY_PAGE_EXTENDED_4	FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x4)
+
+/* MII Registers Page 4 */
+#define AN8855_PBUS_MODE		0x10
+#define   AN8855_PBUS_MODE_ADDR_FIXED	0x0
+#define   AN8855_PBUS_MODE_ADDR_INCR	BIT(15)
+#define AN8855_PBUS_WR_ADDR_HIGH	0x11
+#define AN8855_PBUS_WR_ADDR_LOW		0x12
+#define AN8855_PBUS_WR_DATA_HIGH	0x13
+#define AN8855_PBUS_WR_DATA_LOW		0x14
+#define AN8855_PBUS_RD_ADDR_HIGH	0x15
+#define AN8855_PBUS_RD_ADDR_LOW		0x16
+#define AN8855_PBUS_RD_DATA_HIGH	0x17
+#define AN8855_PBUS_RD_DATA_LOW		0x18
+
+#define AN8855_MAX_PHY_PORT		5
+
+struct an8855 {
+	struct mii_bus *bus;
+	struct mii_bus *phy_bus;
+	unsigned int switch_addr;
+	u16 current_page;
+};
+
+struct an8855_phy {
+	u8 addr;
+	struct an8855 *core;
+};
+
+struct an8855_phy_bus {

drivers/mfd/airoha-an8855.c new file +31 -0

+		return ret;
+	}
+
+	/* Cache current page if next MII read/write is for Switch page */
+	ddata->current_page = page;
+	return 0;
+}
+
+static int an8855_mii_read32(struct mii_bus *bus, u8 phy_id, u32 reg,
+			     u32 *val) __must_hold(&bus->mdio_lock)
+{
+	int lo, hi, ret;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_MODE,
+			      AN8855_PBUS_MODE_ADDR_FIXED);
+	if (ret)
+		goto err;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_RD_ADDR_HIGH,
+			      upper_16_bits(reg));
+	if (ret)
+		goto err;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_RD_ADDR_LOW,
+			      lower_16_bits(reg));
+	if (ret)
+		goto err;
+
+	hi = __mdiobus_read(bus, phy_id, AN8855_PBUS_RD_DATA_HIGH);
+	if (hi < 0) {
+		ret = hi;

drivers/mfd/airoha-an8855.c new file +4 -0

+	return 0;
+err:
+	dev_err_ratelimited(&bus->dev, "failed to read register\n");
+	return ret;

drivers/mfd/airoha-an8855.c new file +18 -0

+}
+
+static int an8855_mii_write32(struct mii_bus *bus, u8 phy_id, u32 reg,
+			      u32 val) __must_hold(&bus->mdio_lock)
+{
+	int ret;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_MODE,
+			      AN8855_PBUS_MODE_ADDR_FIXED);
+	if (ret)
+		goto err;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_WR_ADDR_HIGH,
+			      upper_16_bits(reg));
+	if (ret)
+		goto err;
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_WR_ADDR_LOW,
+			      lower_16_bits(reg));

drivers/mfd/airoha-an8855.c new file +36 -0

+	if (ret)
+		goto err;
+
+	return 0;
+err:
+	dev_err_ratelimited(&bus->dev,
+			    "failed to write an8855 register\n");
+	return ret;
+}
+
+static int an8855_regmap_write(void *ctx, uint32_t reg, uint32_t val)
+{
+	struct an8855 *ddata = ctx;
+	struct mii_bus *bus = ddata->bus;
+	u16 addr = ddata->switch_addr;
+	int ret;
+
+	an8855_regmap_lock(ddata);
+	ret = an8855_mii_set_page(ddata, addr, AN8855_PHY_PAGE_EXTENDED_4);
+	if (ret)
+		goto exit;
+
+	ret = an8855_mii_write32(bus, addr, reg, val);
+
+exit:
+	an8855_regmap_unlock(ddata);
+
+	return ret < 0 ? ret : 0;
+}
+
+static int an8855_regmap_update_bits(void *ctx, uint32_t reg, uint32_t mask,
+				     uint32_t write_val)
+{
+	struct an8855 *ddata = ctx;
+	struct mii_bus *bus = ddata->bus;
+	u16 addr = ddata->switch_addr;

drivers/mfd/airoha-an8855.c new file +78 -0

+		goto exit;
+
+	val &= ~mask;
+	val |= write_val & mask;
+	ret = an8855_mii_write32(bus, addr, reg, val);
+
+exit:
+	an8855_regmap_unlock(ddata);
+
+	return ret < 0 ? ret : 0;
+}
+
+static const struct regmap_range an8855_readable_ranges[] = {
+	regmap_reg_range(0x10000000, 0x10000fff), /* SCU */
+	regmap_reg_range(0x10001000, 0x10001fff), /* RBUS */
+	regmap_reg_range(0x10002000, 0x10002fff), /* MCU */
+	regmap_reg_range(0x10005000, 0x10005fff), /* SYS SCU */
+	regmap_reg_range(0x10007000, 0x10007fff), /* I2C Slave */
+	regmap_reg_range(0x10008000, 0x10008fff), /* I2C Master */
+	regmap_reg_range(0x10009000, 0x10009fff), /* PDMA */
+	regmap_reg_range(0x1000a100, 0x1000a1ff), /* General Purpose Timer */
+	regmap_reg_range(0x1000a200, 0x1000a2ff), /* GPU timer */
+	regmap_reg_range(0x1000a300, 0x1000a3ff), /* GPIO */
+	regmap_reg_range(0x1000a400, 0x1000a5ff), /* EFUSE */
+	regmap_reg_range(0x1000c000, 0x1000cfff), /* GDMP CSR */
+	regmap_reg_range(0x10010000, 0x1001ffff), /* GDMP SRAM */
+	regmap_reg_range(0x10200000, 0x10203fff), /* Switch - ARL Global */
+	regmap_reg_range(0x10204000, 0x10207fff), /* Switch - BMU */
+	regmap_reg_range(0x10208000, 0x1020bfff), /* Switch - ARL Port */
+	regmap_reg_range(0x1020c000, 0x1020cfff), /* Switch - SCH */
+	regmap_reg_range(0x10210000, 0x10213fff), /* Switch - MAC */
+	regmap_reg_range(0x10214000, 0x10217fff), /* Switch - MIB */
+	regmap_reg_range(0x10218000, 0x1021bfff), /* Switch - Port Control */
+	regmap_reg_range(0x1021c000, 0x1021ffff), /* Switch - TOP */
+	regmap_reg_range(0x10220000, 0x1022ffff), /* SerDes */
+	regmap_reg_range(0x10286000, 0x10286fff), /* RG Batcher */
+	regmap_reg_range(0x1028c000, 0x1028ffff), /* ETHER_SYS */
+	regmap_reg_range(0x30000000, 0x37ffffff), /* I2C EEPROM */
+	regmap_reg_range(0x38000000, 0x3fffffff), /* BOOT_ROM */
+	regmap_reg_range(0xa0000000, 0xbfffffff), /* GPHY */
+};
+
+static const struct regmap_access_table an8855_readable_table = {
+	.yes_ranges = an8855_readable_ranges,
+	.n_yes_ranges = ARRAY_SIZE(an8855_readable_ranges),
+};
+
+static const struct regmap_config an8855_regmap_config = {
+	.name = "switch",
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = 0xbfffffff,
+	.reg_read = an8855_regmap_read,
+	.reg_write = an8855_regmap_write,
+	.reg_update_bits = an8855_regmap_update_bits,
+	.disable_locking = true,
+	.rd_table = &an8855_readable_table,
+};
+
+static int an8855_regmap_phy_reset_page(struct an8855 *ddata,
+					int phy) __must_hold(&ddata->bus->mdio_lock)
+{
+	/* Check PHY page only for addr shared with switch */
+	if (phy != ddata->switch_addr)
+		return 0;
+
+	/* Don't restore page if it's not set to Switch page */
+	if (ddata->current_page != AN8855_PHY_PAGE_EXTENDED_4)
+		return 0;
+
+	/*
+	 * Restore page to 0, PHY might change page right after but that
+	 * will be ignored as it won't be a switch page.
+	 */
+	return an8855_mii_set_page(ddata, phy, AN8855_PHY_PAGE_STANDARD);
+}
+

drivers/mfd/airoha-an8855.c new file +16 -0

+
+	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	ret = an8855_regmap_phy_reset_page(core_ddata, addr);
+	if (ret)
+		goto exit;
+
+	ret = __mdiobus_read(bus, addr, reg);
+	if (ret >= 0)
+		*val = ret;
+
+exit:
+	mutex_unlock(&bus->mdio_lock);
+
+	return ret < 0 ? ret : 0;
+}
+

drivers/mfd/airoha-an8855.c new file +34 -0

+
+	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	ret = an8855_regmap_phy_reset_page(core_ddata, addr);
+	if (ret)
+		goto exit;
+
+	ret = __mdiobus_write(bus, addr, reg, val);
+
+exit:
+	mutex_unlock(&bus->mdio_lock);
+
+	return ret;
+}
+
+static const struct regmap_config an8855_phy_regmap_config = {
+	.reg_bits = 16,
+	.val_bits = 16,
+	.reg_read = an8855_regmap_phy_read,
+	.reg_write = an8855_regmap_phy_write,
+	.disable_locking = true,
+	.max_register = 0x1f,
+};
+
+static int an8855_read_switch_id(struct device *dev, struct regmap *regmap)
+{
+	u32 id;
+	int ret;
+
+	ret = regmap_read(regmap, AN8855_CREV, &id);
+	if (ret)
+		return ret;
+
+	if (id != AN8855_ID) {
+		dev_err(dev, "Detected Switch ID %x but %x was expected\n",

drivers/mfd/airoha-an8855.c new file +12 -0

+{
+	struct mdio_regmap_config mrc = { };
+	struct an8855_phy *phy_ddata;
+	struct regmap *regmap;
+	u32 addr, phy_offset;
+	struct mii_bus *bus;
+	int ret;
+
+	ret = of_property_read_u32(phy_np, "reg", &addr);
+	if (ret)
+		return ret;
+

drivers/mfd/airoha-an8855.c new file +27 -0

+	regmap = devm_regmap_init(dev, NULL, phy_ddata, &an8855_phy_regmap_config);
+	if (IS_ERR(regmap))
+		return dev_err_probe(dev, PTR_ERR(regmap),
+				     "phy%d regmap initialization failed\n",
+				      addr);
+
+	mrc.regmap = regmap;
+	mrc.parent = dev;
+	mrc.valid_addr = addr;
+	snprintf(mrc.name, MII_BUS_ID_SIZE, "%s-phy%u", dev_name(dev), addr);
+
+	bus = devm_mdio_regmap_register(dev, &mrc);
+	if (IS_ERR(bus))
+		return PTR_ERR(bus);
+
+	if (addr == ddata->switch_addr)
+		ddata->phy_bus = bus;
+
+	phy_bus_info->bus = bus;
+	phy_bus_info->addr = addr;
+	phy_bus_info->node = fwnode_handle_get(of_fwnode_handle(phy_np));
+
+	return 0;
+}
+
+static int an8855_mdio_register(struct device *dev, struct an8855 *ddata,
+				struct an8855_phy_bus *phy_bus_infos)

drivers/mfd/airoha-an8855.c new file +57 -0

+	}
+
+exit:
+	of_node_put(mdio_np);
+	if (ret) {
+		while (i--)
+			fwnode_handle_put(phy_bus_infos[i].node);
+
+		return ret;
+	}
+
+	return i;
+}
+
+static int an8855_probe(struct mdio_device *mdiodev)
+{
+	struct an8855_phy_bus phy_bus_infos[AN8855_MAX_PHY_PORT] = { };
+	struct device *dev = &mdiodev->dev;
+	struct regmap *regmap;
+	struct an8855 *ddata;
+	int num_phys;
+	int i, ret;
+
+	ddata = devm_kzalloc(dev, sizeof(*ddata), GFP_KERNEL);
+	if (!ddata)
+		return -ENOMEM;
+
+	ddata->bus = mdiodev->bus;
+	ddata->switch_addr = mdiodev->addr;
+	/* No DMA for mdiobus, mute warning for DMA mask not set */
+	dev->dma_mask = &dev->coherent_dma_mask;
+
+	/* Register virtual MDIO for each PHY */
+	num_phys = an8855_mdio_register(dev, ddata, phy_bus_infos);
+	if (num_phys < 0)
+		return num_phys;
+
+	regmap = devm_regmap_init(dev, NULL, ddata, &an8855_regmap_config);
+	if (IS_ERR(regmap)) {
+		ret = PTR_ERR(regmap);
+		dev_err_probe(dev, ret, "regmap initialization failed\n");
+		goto err_put_fwnodes;
+	}
+
+	/* Reset PHY page for switch address */
+	mutex_lock_nested(&ddata->bus->mdio_lock, MDIO_MUTEX_NESTED);
+	ret = an8855_mii_set_page(ddata, ddata->switch_addr,
+				  AN8855_PHY_PAGE_STANDARD);
+	mutex_unlock(&ddata->bus->mdio_lock);
+	if (ret)
+		goto err_put_fwnodes;
+
+	ret = an8855_read_switch_id(dev, regmap);
+	if (ret)
+		goto err_put_fwnodes;
+
+	/* Release global PHY power down */

drivers/mfd/airoha-an8855.c new file +11 -0

+	.probe = an8855_probe,
+	.mdiodrv.driver = {
+		.name = "an8855",
+		.of_match_table = an8855_of_match,
+	},
+};
+mdio_module_driver(an8855_driver);
+
+MODULE_AUTHOR("Christian Marangi <[email protected]>");
+MODULE_DESCRIPTION("Driver for Airoha AN8855");
+MODULE_LICENSE("GPL");

Signature · 1 line

2.55.0