Bluetooth: Add support for HDT and EKS
Subsystems (2)
Luiz Augusto von Dentz
maintainerv8 cover Bluetooth: Add support for HDT and EKS
From: Luiz Augusto von Dentz <[email protected]>
This adds support for the LE High Data Throughput (HDT) PHY and the Encryption Key Schedule (EKS) introduced in Bluetooth Core 7.0:
- HDT PHY selection for ACL, CIS and BIS, the v2/v3 HCI commands and events that carry the HDT rates, and the LE Set HDT Default Parameters command.
- ISO sockets take an extended, versioned QoS (struct bt_iso_qos_ext) through the existing BT_ISO_QOS option, carrying the HDT rates per direction; the legacy struct bt_iso_qos keeps working.
- LE Enable Encryption v2 with the MIC length, Encryption Change v3 and Key Refresh Complete v2.
- L2CAP and BT_SECURITY gain a MIC length requirement; connections whose MIC is too short are refused with the MIC Length Too Short result.
- EKS opportunistic encryption, enabled with a new MGMT system configuration parameter.
This series depends on:
"Bluetooth: Fix not updating of hdev->commands[] after reset"
Changes in v8:
- The ISO QoS rates are validated: reserved bits, or rates without BT_ISO_PHY_HDT, are rejected rather than passed to the controller.
Changes in v7:
- The MIC length of LE Enable Encryption v2 is taken when the command is sent, so channels raising it after it was queued are taken into account, and incoming LE and Enhanced Credit Based connection requests record the MIC length of the listening channel before checking the security.
- A failed Key Refresh Complete reporting opportunistic encryption is handled as any other failed refresh, disconnecting the link.
Changes in v6:
- An encryption command that fails without a Command Status is handled where it is sent, aborting the link with hci_abort_conn_sync() without holding hdev->lock, rather than from its completion callback, which could deadlock, also when canceled, and drop the connection twice. LE Start Encryption's Command Status error now clears the pending encryption too.
- Opportunistic encryption sends its command without that handling, so its failure can't disconnect a link SMP is encrypting.
- SMP doesn't distribute keys on opportunistic encryption.
- An Encryption Change failure on an opportunistically encrypted link is handled as for any encrypted link, clearing its encryption flags.
Changes in v5:
- A CIS bound with BT_ISO_PHY_ANY keeps the GFSK PHYs of the ACL, as HDT isn't part of it, so a deferred CIS setup matches its binding.
- LE Remote Features Complete clears HDT from the default PHYs, as HDT is a feature of page 1 which it doesn't report.
- CIS Established v3 takes Max_SDU from its SDU fields rather than Max_PDU.
- The default data length is only skipped if both its length and time are already at their maximum.
- Encryption commands that fail without a Command Status clear the pending encryption and disconnect, as a Command Status error does, and are freed with kfree_sensitive() as they carry the key.
- SMP starts encryption after DHKey Check before adding the LTK, so a failure doesn't remove a previously stored key.
- Encryption Change v3 reporting opportunistic encryption for a link with a key from pairing disconnects it, as Key Refresh Complete does, and only a failure is taken as the one of an opportunistic encryption being started. A failed key refresh replacing the opportunistic key no longer reports the link as encrypted.
Changes in v4:
- LE Set CIG Parameters v2 is limited to the CIS that fit in the 255 octets of command parameters, and a CIS that would exceed that is refused when it is bound to the CIG.
- setsockopt(BT_ISO_QOS) on a socket that already has a connection, such as with deferred setup or a PA sync, checks the QoS type there, since connect() or listen() won't.
- SMP marks the encryption started after DHKey Check as pending, as it does after Random, so it isn't started a second time.
- A Key Refresh Complete reporting opportunistic encryption, such as one changing the MIC length, keeps the link opportunistic, and disconnects a link with a key from pairing since that would be a downgrade. A key from pairing replacing the opportunistic one is handled as Encryption Change is for an unencrypted link.
- Restore the lockdep_assert_held() before smp_pairing_in_progress(), which context analysis needs to know conn->hdev->lock is held.
Changes in v3:
- Opportunistic encryption sets HCI_CONN_ENCRYPT and HCI_CONN_AES_CCM along with a new HCI_CONN_OPP_ENCRYPT flag, and the L2CAP key size check is skipped for it since it has no key from pairing. Pairing over such a link now completes: its Key Refresh Complete clears the flag. A failure, or a command that can't be sent, leaves the link unencrypted instead of disconnecting, and HCI_CONN_ENCRYPT_PEND is no longer used for it so it doesn't block SMP. The MIC length is taken right before the command is sent.
- Changing TLV 0x0024 while the controller is up updates the Opportunistic Encryption host feature bit.
- SMP checks the result of hci_le_enable_encrypt().
- Set CIG Parameters v2 returns the failure of a response that doesn't match the command, and fails the unbound CIS of the CIG it was sent for.
- CIS Established v3 and Create BIG Complete v2 are only unmasked with CIS and BIS support.
- BT_PHY rejects HDT6 and HDT7.5 rates the controller doesn't support in that direction, and only reports supported ones.
- struct bt_iso_qos_ext replaces its rfu bytes with a 16-bit version and a 16-bit type telling whether the unicast or broadcast member is in use, so each can later grow on its own; the union is the last member for that. BT_ISO_QOS_ANY, used for struct bt_iso_qos, leaves the type to connect() or listen(), which fail with -EINVAL on a mismatch. Connections set up by the controller get the version and type, and BT_ISO_HDT_RATE_* name the rates bits.
- The extended ISO QoS is copied field by field, so padding is zeroed, and the v1 CIS Established event clears the HDT rates.
Changes in v2:
- Remove the values from drafts of the specification and use the ones from Core 7.0: L2CAP MIC Length Too Short is 0x000C for LE Credit Based and 0x0010 for Enhanced Credit Based, and LE feature page 0 bit 59 is no longer checked.
- A 64-bit MIC is only used when both sides prefer it, so downgrading on re-encryption is no longer an error.
- The key size of Encryption Change v3 is ignored for LE as the spec requires; hci_change_encrypt() no longer takes it.
- Rename struct bt_iso_qos_v2 to struct bt_iso_qos_ext with a version field; the length passed to BT_ISO_QOS selects legacy or extended. Convert field by field, which fixes an out-of-bounds copy and an info leak through the legacy struct.
- HDT rates are little endian and kept per direction.
- HDT PHY selection is gated on hdt_capable(); mixed LE and HDT PHY masks are accepted; phy_opts is initialized.
- Create BIG Complete v1/v2 share one bounds-checked handler; Set CIG Parameters v2 response is validated like v1; Create CIS waits for CIS Established v3.
- Drop the unused LE Set Data Length v2 command and the unhandled Data Length Change v2 event mask bit.
- EKS: copy the LTK under RCU and encrypt after unlocking, zero-pad the key for v1 and copy key_size bytes for v2, free the command when queueing fails, and handle the Command Status of LE Enable Encryption v2.
- L2CAP: keep the requested MIC length separate from the negotiated one, take the negotiated one from Encryption Change v3 and Key Refresh Complete v2, propagate the channel MIC length on every LE security path and reject values above 0x02.
- RFCOMM BT_SECURITY accepts the 2-byte struct and zeroes the struct returned by getsockopt.
- One hci_le_set_hdt_params_sync() is shared by init and MGMT, and the defaults are resent when changed while the controller is up.
- Opportunistic encryption requires eks_capable() and its TLV (0x0024) is validated as u8. Encryption Change v3 for it still only clears ENCRYPT_PEND: the key size is 0, so setting ENCRYPT would make the key size check refuse every L2CAP channel.
Luiz Augusto von Dentz (6):
Bluetooth: Add initial support for HDT PHY
Bluetooth: ISO: Add extended QoS with the HDT rates
Bluetooth: Add initial support for EKS
Bluetooth: L2CAP: Add MIC length validation for HDT PHY
Bluetooth: Add HCI_OP_LE_SET_HDT_DEFAULT_PARAMS support
Bluetooth: Add EKS Opportunistic Encryption support
include/net/bluetooth/bluetooth.h | 102 +++++ include/net/bluetooth/hci.h | 216 +++++++++- include/net/bluetooth/hci_core.h | 66 ++- include/net/bluetooth/hci_sync.h | 12 +- include/net/bluetooth/l2cap.h | 7 + include/net/bluetooth/mgmt.h | 1 + net/bluetooth/hci_conn.c | 279 +++++++----- net/bluetooth/hci_core.c | 4 + net/bluetooth/hci_event.c | 680 +++++++++++++++++++++++++---- net/bluetooth/hci_sync.c | 691 +++++++++++++++++++++++++++++- net/bluetooth/iso.c | 264 +++++++++++- net/bluetooth/l2cap_core.c | 60 ++- net/bluetooth/l2cap_sock.c | 23 +- net/bluetooth/mgmt.c | 6 + net/bluetooth/mgmt_config.c | 56 +++ net/bluetooth/rfcomm/sock.c | 13 +- net/bluetooth/smp.c | 96 ++++- net/bluetooth/smp.h | 2 + 18 files changed, 2323 insertions(+), 255 deletions(-)
Signature · 1 line
2.56.0
Luiz Augusto von Dentz
maintainerPATCH v8 1/6 Bluetooth: Add initial support for HDT PHY
From: Luiz Augusto von Dentz <[email protected]>
Add support for the LE HDT PHY introduced by High Data Throughput (HDT) in Bluetooth 7.0:
- The HDT feature bits (Link Layer feature bits 76-83) and the le_feature() helper to access the FeatureSet pages above page 0, along with hdt_capable() and the per-rate capability checks.
- BT_PHY_HDT_* bits for the HDT2, HDT3, HDT4, HDT6 and HDT7.5 rates in each direction, so userspace can select them with BT_PHY, which map to the LE HDT PHY and the rate bits of PHY_Options in LE Set PHY.
- LE Read Maximum Data Length v2 and LE Read/Write Suggested Default Data Length v2, used instead of their v1 counterparts on HDT capable controllers so the default data length is set for each PHY. The values given to LE Write Suggested Default Data Length are clamped to the maximum the specification allows.
- LE Set CIG Parameters v2, LE CIS Established v3, LE Create BIG v2 and LE Create BIG Complete v2, which carry the HDT rates, MIC length and packet format of a CIS or BIS. The CIS and BIS default to all the HDT rates the controller supports when the HDT PHY is selected.
- MGMT_SETTING_HDT to report HDT support to userspace.
--- include/net/bluetooth/bluetooth.h | 18 ++ include/net/bluetooth/hci.h | 178 ++++++++++++++- include/net/bluetooth/hci_core.h | 29 +++ include/net/bluetooth/hci_sync.h | 5 +- include/net/bluetooth/mgmt.h | 1 + net/bluetooth/hci_conn.c | 227 ++++++++++++------- net/bluetooth/hci_event.c | 363 ++++++++++++++++++++++++++++-- net/bluetooth/hci_sync.c | 358 ++++++++++++++++++++++++++++- net/bluetooth/iso.c | 2 +- net/bluetooth/mgmt.c | 6 + 10 files changed, 1075 insertions(+), 112 deletions(-)
include/net/bluetooth/bluetooth.h +18 -0
@@ -142,6 +142,16 @@ struct bt_voice {#define BT_PHY_LE_2M_RX BIT(12)#define BT_PHY_LE_CODED_TX BIT(13)#define BT_PHY_LE_CODED_RX BIT(14) +#define BT_PHY_HDT_2M_TX BIT(15) +#define BT_PHY_HDT_2M_RX BIT(16) +#define BT_PHY_HDT_3M_TX BIT(17) +#define BT_PHY_HDT_3M_RX BIT(18) +#define BT_PHY_HDT_4M_TX BIT(19) +#define BT_PHY_HDT_4M_RX BIT(20) +#define BT_PHY_HDT_6M_TX BIT(21) +#define BT_PHY_HDT_6M_RX BIT(22) +#define BT_PHY_HDT_7_5M_TX BIT(23) +#define BT_PHY_HDT_7_5M_RX BIT(24)#define BT_PHY_BREDR_MASK (BT_PHY_BR_1M_1SLOT | BT_PHY_BR_1M_3SLOT | \ BT_PHY_BR_1M_5SLOT | BT_PHY_EDR_2M_1SLOT | \
@@ -151,6 +161,13 @@ struct bt_voice {#define BT_PHY_LE_MASK (BT_PHY_LE_1M_TX | BT_PHY_LE_1M_RX | \ BT_PHY_LE_2M_TX | BT_PHY_LE_2M_RX | \ BT_PHY_LE_CODED_TX | BT_PHY_LE_CODED_RX) +#define BT_PHY_HDT_TX_MASK (BT_PHY_HDT_2M_TX | BT_PHY_HDT_3M_TX | \ + BT_PHY_HDT_4M_TX | BT_PHY_HDT_6M_TX | \ + BT_PHY_HDT_7_5M_TX) +#define BT_PHY_HDT_RX_MASK (BT_PHY_HDT_2M_RX | BT_PHY_HDT_3M_RX | \ + BT_PHY_HDT_4M_RX | BT_PHY_HDT_6M_RX | \ + BT_PHY_HDT_7_5M_RX) +#define BT_PHY_HDT_MASK (BT_PHY_HDT_TX_MASK | BT_PHY_HDT_RX_MASK)#define BT_MODE 15
@@ -221,6 +238,7 @@ struct bt_iso_qos {#define BT_ISO_PHY_1M BIT(0)#define BT_ISO_PHY_2M BIT(1)#define BT_ISO_PHY_CODED BIT(2) +#define BT_ISO_PHY_HDT BIT(4)#define BT_ISO_PHY_ANY (BT_ISO_PHY_1M | BT_ISO_PHY_2M | \ BT_ISO_PHY_CODED)
include/net/bluetooth/hci.h +174 -4
208 lines not on this page · raw message
include/net/bluetooth/hci_core.h +29 -0
@@ -424,6 +424,15 @@ struct hci_dev {__u16 le_max_tx_time;__u16 le_max_rx_len;__u16 le_max_rx_time; +__u16 hdt_def_tx_len; +__u16 hdt_def_tx_time; +__u16 hdt_max_tx_len; +__u16 hdt_max_tx_time; +__u16 hdt_max_rx_len; +__u16 hdt_max_rx_time; +__u8 hdt_max_tx_win; +__u8 hdt_max_rx_win; +__u16 hdt_max_rx_packet;__u8 le_max_key_size;__u8 le_min_key_size;__u16 discov_interleaved_timeout;
@@ -784,6 +793,7 @@ struct hci_conn {__u8 le_rx_def_phys;__u8 le_tx_phy;__u8 le_rx_phy; +__u16 le_phy_opts;__s8 rssi;__s8 tx_power;__s8 max_tx_power;
@@ -2148,6 +2158,25 @@ void hci_conn_del_sysfs(struct hci_conn *conn); (past_sender_enabled(dev) || past_receiver_enabled(dev))#define ll_ext_feature_capable (dev) \ ((dev)->le_features[7] & HCI_LE_LL_EXT_FEATURE) +#define le_feature (dev, page, byte) \ + (page ? ((dev)->le_features[(page - 1) * 24 + 8 + byte]) : \ + ((dev)->le_features[byte])) +#define hdt_capable (dev) \ + (le_feature(dev, 1, 1) & HCI_LE_HDT_FEATURE) +#define le_set_cig_params_v2_capable (dev) \ + (hdt_capable(dev) && ((dev)->commands[51] & BIT(0))) +#define hdt_enabled (dev) \ + (le_enabled(dev) && hdt_capable(dev)) +#define hdt_6_rx_capable (dev) \ + (le_feature(dev, 1, 1) & HCI_LE_HDT_6_RX_FEATURE) +#define hdt_6_tx_capable (dev) \ + (le_feature(dev, 1, 1) & HCI_LE_HDT_6_TX_FEATURE) +#define hdt_7_5_rx_capable (dev) \ + (le_feature(dev, 1, 2) & HCI_LE_HDT_7_5_RX_FEATURE) +#define hdt_7_5_tx_capable (dev) \ + (le_feature(dev, 1, 2) & HCI_LE_HDT_7_5_TX_FEATURE) +#define hdt_pf1_capable (dev) \ + (le_feature(dev, 1, 2) & HCI_LE_HDT_PF_1)/* Channel sounding support */ #define le_cs_capable (dev) \
include/net/bluetooth/hci_sync.h +4 -1
@@ -193,4 +193,7 @@ int hci_past_sync(struct hci_conn *conn, struct hci_conn *le);int hci_le_read_remote_features (struct hci_conn *conn);int hci_acl_change_pkt_type (struct hci_conn *conn,u16 pkt_type); -int hci_le_set_phy (struct hci_conn *conn,u8 tx_phys,u8 rx_phys); +int hci_le_set_phy (struct hci_conn *conn,u8 tx_phys,u8 rx_phys,u16 phy_opts); +int hci_le_set_cig_params_sync (struct hci_dev *hdev,u8 cig_id); +int hci_le_create_big_sync (struct hci_conn *conn,struct bt_iso_qos *qos, +u8 num_bis);
include/net/bluetooth/mgmt.h +1 -0
@@ -119,6 +119,7 @@ struct mgmt_rp_read_index_list {#define MGMT_SETTING_PAST_SENDER BIT(23)#define MGMT_SETTING_PAST_RECEIVER BIT(24)#define MGMT_SETTING_SCI BIT(25) +#define MGMT_SETTING_HDT BIT(26)#define MGMT_OP_READ_INFO 0x0004#define MGMT_READ_INFO_SIZE 0
net/bluetooth/hci_conn.c +146 -81
294 lines not on this page · raw message
net/bluetooth/hci_event.c +341 -22
478 lines not on this page · raw message
net/bluetooth/hci_sync.c +355 -3
428 lines not on this page · raw message
net/bluetooth/iso.c +1 -1
@@ -1875,7 +1875,7 @@ static bool check_io_qos(struct bt_iso_io_qos *qos)if (qos->latency && (qos->latency <0x05 || qos->latency >0xfa0 ))return false; -if (qos->phys >BT_ISO_PHY_ANY ) +if (qos->phys & ~(BT_ISO_PHY_ANY |BT_ISO_PHY_HDT ))return false;return true;
net/bluetooth/mgmt.c +6 -0
@@ -865,6 +865,9 @@ static u32 get_supported_settings(struct hci_dev *hdev)if (le_sci_capable (hdev)) settings |=MGMT_SETTING_SCI ; +if (hdt_capable (hdev)) + settings |=MGMT_SETTING_HDT ; + settings |=MGMT_SETTING_PHY_CONFIGURATION ;return settings;
@@ -959,6 +962,9 @@ static u32 get_current_settings(struct hci_dev *hdev)if (le_sci_enabled (hdev)) settings |=MGMT_SETTING_SCI ; +if (hdt_enabled (hdev)) + settings |=MGMT_SETTING_HDT ; +return settings; }
Signature · 1 line
2.56.0
This is automated email and please do not reply to this email!
Dear submitter,
Thank you for submitting the patches to the linux bluetooth mailing list. This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/series/1204429/
---Test result---
Test Summary:
CheckPatch PASS 12.99 seconds VerifyFixes PASS 0.13 seconds VerifySignedoff PASS 0.13 seconds GitLint PASS 1.93 seconds SubjectPrefix PASS 0.74 seconds BuildKernel PASS 23.90 seconds CheckAllWarning PASS 27.96 seconds CheckSparse WARNING 32.03 seconds BuildKernel32 PASS 23.86 seconds CheckKernelLLVM PASS 24.84 seconds TestRunnerSetup PASS 553.02 seconds TestRunner_l2cap-tester PASS 13.23 seconds TestRunner_iso-tester PASS 9.68 seconds TestRunner_bnep-tester PASS 2.99 seconds TestRunner_mgmt-tester PASS 84.05 seconds TestRunner_rfcomm-tester PASS 4.14 seconds TestRunner_sco-tester PASS 5.19 seconds TestRunner_ioctl-tester PASS 4.34 seconds TestRunner_mesh-tester PASS 5.19 seconds TestRunner_smp-tester PASS 4.06 seconds TestRunner_userchan-tester PASS 2.96 seconds TestRunner_6lowpan-tester PASS 12.60 seconds IncrementalBuild PASS 106.40 seconds
Details
##############################
Test: CheckSparse - WARNING
Desc: Run sparse tool with linux kernel
Output:net/bluetooth/hci_event.c: note: in included file (through include/net/bluetooth/hci_core.h):net/bluetooth/hci_event.c: note: in included file (through include/net/bluetooth/hci_core.h):net/bluetooth/hci_event.c: note: in included file (through include/net/bluetooth/hci_core.h):net/bluetooth/hci_event.c: note: in included file (through include/net/bluetooth/hci_core.h):net/bluetooth/hci_event.c: note: in included file (through include/net/bluetooth/hci_core.h):
https://github.com/bluez/bluetooth-next/pull/1081
---
Regards,
Linux Bluetooth
Luiz Augusto von Dentz
maintainerPATCH v8 2/6 Bluetooth: ISO: Add extended QoS with the HDT rates
In reply to Luiz Augusto von DentzFrom: Luiz Augusto von Dentz <[email protected]>
Add struct bt_iso_qos_ext, an extensible version of struct bt_iso_qos, so new QoS fields can be added without defining a new socket option or struct each time. It starts with two fields:
- version tells which fields are valid, so later versions can add fields while applications built for an earlier version keep working.
- type tells which member of the union is in use, unicast or broadcast. The QoS is usually set before bind() or connect(), when the socket can't tell which one it was given, so without type the two could only grow together. With it, each can be extended on its own by adding fields at its end, which is also why the union is the last member.
BT_ISO_QOS_ANY leaves the type to connect() or listen(), which set it. That works for version 1 since its unicast fields are a prefix of the broadcast ones, and is what struct bt_iso_qos uses. A type that doesn't match how the socket is used makes connect() or listen() fail with -EINVAL, or setsockopt() on a socket that already has a connection, such as with deferred setup or a PA sync.
Version 1 adds the rates of each direction, BT_ISO_HDT_RATE_*, so userspace can select the HDT rates of a CIS or BIS along with BT_ISO_PHY_HDT; 0 selects every rate the controller supports.
BT_ISO_QOS accepts either struct: the length of struct bt_iso_qos selects it, as before, and any other length must carry struct bt_iso_qos_ext of a known version and type. The struct is copied field by field, so its padding is zeroed. Reading BT_ISO_QOS with a buffer shorter than struct bt_iso_qos_ext returns struct bt_iso_qos, so existing userspace is not affected; otherwise the version and type in use are reported, including for connections set up by the controller.
The ISO sockets keep the extended form internally, so the rates are passed to LE Set CIG Parameters v2 and LE Create BIG v2, and reported back from LE CIS Established v3 and LE Create BIG Complete v2.
--- include/net/bluetooth/bluetooth.h | 83 ++++++++++ include/net/bluetooth/hci_core.h | 15 +- include/net/bluetooth/hci_sync.h | 2 +- net/bluetooth/hci_conn.c | 34 ++-- net/bluetooth/hci_event.c | 20 ++- net/bluetooth/hci_sync.c | 32 ++-- net/bluetooth/iso.c | 262 ++++++++++++++++++++++++++++-- 7 files changed, 393 insertions(+), 55 deletions(-)
include/net/bluetooth/bluetooth.h +83 -0
@@ -235,6 +235,89 @@ struct bt_iso_qos { }; }; +/* Extended ISO QoS, set and read with BT_ISO_QOS. +* +* The option length tells it apart from struct bt_iso_qos, which is kept for +* existing applications. New fields are added by extending this struct rather +* than by adding new socket options or structs: +* +* - version tells which fields are valid, so later versions can add fields +* while older applications keep working with the fields they know. +* - type tells which member of the union is in use. The QoS is usually set +* before bind() or connect(), so the socket can't tell unicast from +* broadcast at that point. With type, struct bt_iso_ucast_qos_ext and +* struct bt_iso_bcast_qos_ext can each grow on their own, by adding fields +* at their end, without the kernel having to guess which one it was given. +* For that the union shall remain the last member. +* +* BT_ISO_QOS_ANY leaves the type to be set by connect() or listen(), which is +* possible with version 1 since its unicast fields are a prefix of the +* broadcast ones. A type that doesn't match how the socket is used makes +* connect() or listen() fail with -EINVAL, or setsockopt() on a socket that +* already has a connection, such as with deferred setup. getsockopt() reports +* the type in use once it is known. +* +* Version 1 adds the HDT rates of each direction, see BT_ISO_HDT_RATE_*, used +* when the PHY is BT_ISO_PHY_HDT; 0 means every rate the controller supports. +*/ +#define BT_ISO_QOS_VERSION_1 0x0001 + +#define BT_ISO_QOS_ANY 0x0000 +#define BT_ISO_QOS_UCAST 0x0001 +#define BT_ISO_QOS_BCAST 0x0002 + +#define BT_ISO_HDT_RATE_2M BIT(0) +#define BT_ISO_HDT_RATE_3M BIT(1) +#define BT_ISO_HDT_RATE_4M BIT(2) +#define BT_ISO_HDT_RATE_6M BIT(3) +#define BT_ISO_HDT_RATE_7_5M BIT(4) + +struct bt_iso_io_qos_ext { +__u32 interval; +__u16 latency; +__u16 sdu; +__u8 phys; +__u8 rtn; +__u16 rates; +}; + +struct bt_iso_ucast_qos_ext { +__u8 cig; +__u8 cis; +__u8 sca; +__u8 packing; +__u8 framing; +struct bt_iso_io_qos_ext in; +struct bt_iso_io_qos_ext out; +}; + +struct bt_iso_bcast_qos_ext { +__u8 big; +__u8 bis; +__u8 sync_factor; +__u8 packing; +__u8 framing; +struct bt_iso_io_qos_ext in; +struct bt_iso_io_qos_ext out; +__u8 encryption; +__u8 bcode[16 ]; +__u8 options; +__u16 skip; +__u16 sync_timeout; +__u8 sync_cte_type; +__u8 mse; +__u16 timeout; +}; + +struct bt_iso_qos_ext { +__u16 version; +__u16 type; +union {/* Shall be the last member */ +struct bt_iso_ucast_qos_ext ucast; +struct bt_iso_bcast_qos_ext bcast; + }; +}; +#define BT_ISO_PHY_1M BIT(0)#define BT_ISO_PHY_2M BIT(1)#define BT_ISO_PHY_CODED BIT(2)
include/net/bluetooth/hci_core.h +8 -7
@@ -797,7 +797,7 @@ struct hci_conn {__s8 rssi;__s8 tx_power;__s8 max_tx_power; -struct bt_iso_qos iso_qos; +struct bt_iso_qos_ext iso_qos;__u8 num_bis;__u8 bis[HCI_MAX_ISO_BIS ];
@@ -1678,23 +1678,24 @@ struct hci_conn *hci_connect_sco(struct hci_dev *hdev, int type, bdaddr_t *dst, __u16 setting, struct bt_codec *codec, u16 timeout);struct hci_conn *hci_bind_cis (struct hci_dev *hdev,bdaddr_t *dst, -__u8 dst_type,struct bt_iso_qos *qos, +__u8 dst_type,struct bt_iso_qos_ext *qos,u16 timeout);struct hci_conn *hci_bind_bis (struct hci_dev *hdev,bdaddr_t *dst,__u8 sid, -struct bt_iso_qos *qos, +struct bt_iso_qos_ext *qos,__u8 base_len,__u8 *base,u16 timeout);int hci_past_bis (struct hci_conn *conn,bdaddr_t *dst,__u8 dst_type);struct hci_conn *hci_connect_cis (struct hci_dev *hdev,bdaddr_t *dst, -__u8 dst_type,struct bt_iso_qos *qos, +__u8 dst_type,struct bt_iso_qos_ext *qos,u16 timeout);struct hci_conn *hci_connect_bis (struct hci_dev *hdev,bdaddr_t *dst,__u8 dst_type,__u8 sid, -struct bt_iso_qos *qos, +struct bt_iso_qos_ext *qos,__u8 data_len,__u8 *data,u16 timeout);struct hci_conn *hci_pa_create_sync (struct hci_dev *hdev,bdaddr_t *dst, -__u8 dst_type,__u8 sid,struct bt_iso_qos *qos); +__u8 dst_type,__u8 sid, +struct bt_iso_qos_ext *qos);int hci_conn_big_create_sync (struct hci_dev *hdev,struct hci_conn *hcon, -struct bt_iso_qos *qos,__u16 sync_handle, +struct bt_iso_qos_ext *qos,__u16 sync_handle,__u8 num_bis,__u8 bis[]);int hci_conn_check_link_mode (struct hci_conn *conn);int hci_conn_check_secure (struct hci_conn *conn,__u8 sec_level);
include/net/bluetooth/hci_sync.h +1 -1
@@ -195,5 +195,5 @@ int hci_le_read_remote_features(struct hci_conn *conn);int hci_acl_change_pkt_type (struct hci_conn *conn,u16 pkt_type);int hci_le_set_phy (struct hci_conn *conn,u8 tx_phys,u8 rx_phys,u16 phy_opts);int hci_le_set_cig_params_sync (struct hci_dev *hdev,u8 cig_id); -int hci_le_create_big_sync (struct hci_conn *conn,struct bt_iso_qos *qos, +int hci_le_create_big_sync (struct hci_conn *conn,struct bt_iso_qos_ext *qos,u8 num_bis);
net/bluetooth/hci_conn.c +21 -13
@@ -1120,6 +1120,12 @@ static struct hci_conn *__hci_conn_add(struct hci_dev *hdev, int type, conn->cleanup = cis_cleanup; conn->mtu = hdev->iso_mtu; + +/* Set for connections the controller sets up, such as an +* incoming CIS, sockets replace it with their own QoS. +*/ + conn->iso_qos.version =BT_ISO_QOS_VERSION_1 ; + conn->iso_qos.type =BT_ISO_QOS_UCAST ;break ;case PA_LINK :case BIS_LINK :
@@ -1127,6 +1133,8 @@ static struct hci_conn *__hci_conn_add(struct hci_dev *hdev, int type,hci_copy_identity_address (hdev, &conn->src, &conn->src_type); conn->cleanup = bis_cleanup; conn->mtu = hdev->iso_mtu; + conn->iso_qos.version =BT_ISO_QOS_VERSION_1 ; + conn->iso_qos.type =BT_ISO_QOS_BCAST ;break ;case SCO_LINK :if (lmp_esco_capable (hdev))
@@ -1637,7 +1645,7 @@ static int hci_explicit_conn_params_set(struct hci_dev *hdev,return 0 ; } -static int qos_set_big (struct hci_dev *hdev,struct bt_iso_qos *qos) +static int qos_set_big (struct hci_dev *hdev,struct bt_iso_qos_ext *qos) {struct hci_conn *conn;u8 big;
@@ -1661,7 +1669,7 @@ static int qos_set_big(struct hci_dev *hdev, struct bt_iso_qos *qos)return 0 ; } -static int qos_set_bis (struct hci_dev *hdev,struct bt_iso_qos *qos) +static int qos_set_bis (struct hci_dev *hdev,struct bt_iso_qos_ext *qos) {struct hci_conn *conn;u8 bis;
@@ -1703,7 +1711,7 @@ static int qos_set_bis(struct hci_dev *hdev, struct bt_iso_qos *qos)/* This function requires the caller holds hdev->lock */ static struct hci_conn *hci_add_bis (struct hci_dev *hdev,bdaddr_t *dst, -__u8 sid,struct bt_iso_qos *qos, +__u8 sid,struct bt_iso_qos_ext *qos,__u8 base_len,__u8 *base,u16 timeout) {struct hci_conn *conn;
@@ -1938,7 +1946,7 @@ struct hci_conn *hci_connect_sco(struct hci_dev *hdev, int type, bdaddr_t *dst,return sco; } -static int hci_le_create_big (struct hci_conn *conn,struct bt_iso_qos *qos) +static int hci_le_create_big (struct hci_conn *conn,struct bt_iso_qos_ext *qos) {struct hci_dev *hdev = conn->hdev;struct iso_list_data data;
@@ -1961,7 +1969,7 @@ static int set_cig_params_sync(struct hci_dev *hdev, void *data)return hci_le_set_cig_params_sync (hdev, cig_id); } -static bool hci_le_set_cig_params (struct hci_conn *conn,struct bt_iso_qos *qos) +static bool hci_le_set_cig_params (struct hci_conn *conn,struct bt_iso_qos_ext *qos) {struct hci_dev *hdev = conn->hdev;struct iso_list_data data;
@@ -2037,7 +2045,7 @@ static bool hci_le_set_cig_params(struct hci_conn *conn, struct bt_iso_qos *qos) }struct hci_conn *hci_bind_cis (struct hci_dev *hdev,bdaddr_t *dst, -__u8 dst_type,struct bt_iso_qos *qos, +__u8 dst_type,struct bt_iso_qos_ext *qos,u16 timeout) {struct hci_conn *cis;
@@ -2180,7 +2188,7 @@ int hci_le_create_cis_pending(struct hci_dev *hdev) }static void hci_iso_qos_setup (struct hci_dev *hdev,struct hci_conn *conn, -struct bt_iso_io_qos *qos,__u8 phys) +struct bt_iso_io_qos_ext *qos,__u8 phys) {/* Only set MTU if PHY is enabled */ if (!qos->sdu && qos->phys)
@@ -2205,7 +2213,7 @@ static void hci_iso_qos_setup(struct hci_dev *hdev, struct hci_conn *conn,static int create_big_sync (struct hci_dev *hdev,void *data) {struct hci_conn *conn = data; -struct bt_iso_qos *qos = &conn->iso_qos; +struct bt_iso_qos_ext *qos = &conn->iso_qos;u16 interval, sync_interval =0 ;u32 flags =0 ;int err;
@@ -2234,7 +2242,7 @@ static int create_big_sync(struct hci_dev *hdev, void *data)struct hci_conn *hci_pa_create_sync (struct hci_dev *hdev,bdaddr_t *dst,__u8 dst_type,__u8 sid, -struct bt_iso_qos *qos) +struct bt_iso_qos_ext *qos) {struct hci_conn *conn;
@@ -2257,7 +2265,7 @@ struct hci_conn *hci_pa_create_sync(struct hci_dev *hdev, bdaddr_t *dst, }int hci_conn_big_create_sync (struct hci_dev *hdev,struct hci_conn *hcon, -struct bt_iso_qos *qos,__u16 sync_handle, +struct bt_iso_qos_ext *qos,__u16 sync_handle,__u8 num_bis,__u8 bis[]) {int err;
@@ -2308,7 +2316,7 @@ static void create_big_complete(struct hci_dev *hdev, void *data, int err) }struct hci_conn *hci_bind_bis (struct hci_dev *hdev,bdaddr_t *dst,__u8 sid, -struct bt_iso_qos *qos, +struct bt_iso_qos_ext *qos,__u8 base_len,__u8 *base,u16 timeout) {struct hci_conn *conn;
@@ -2396,7 +2404,7 @@ static void bis_mark_per_adv(struct hci_conn *conn, void *data)struct hci_conn *hci_connect_bis (struct hci_dev *hdev,bdaddr_t *dst,__u8 dst_type,__u8 sid, -struct bt_iso_qos *qos, +struct bt_iso_qos_ext *qos,__u8 base_len,__u8 *base,u16 timeout) {struct hci_conn *conn;
@@ -2447,7 +2455,7 @@ struct hci_conn *hci_connect_bis(struct hci_dev *hdev, bdaddr_t *dst, }struct hci_conn *hci_connect_cis (struct hci_dev *hdev,bdaddr_t *dst, -__u8 dst_type,struct bt_iso_qos *qos, +__u8 dst_type,struct bt_iso_qos_ext *qos,u16 timeout) {struct hci_conn *le;
net/bluetooth/hci_event.c +15 -5
@@ -7389,7 +7389,7 @@ static void hci_le_cis_established_evt(struct hci_dev *hdev, void *data, {struct hci_evt_le_cis_established *ev = data;struct hci_conn *conn; -struct bt_iso_qos *qos; +struct bt_iso_qos_ext *qos;bool pending = false;u16 handle =__le16_to_cpu (ev->handle);u32 c_sdu_interval, p_sdu_interval;
@@ -7415,6 +7415,10 @@ static void hci_le_cis_established_evt(struct hci_dev *hdev, void *data, qos = &conn->iso_qos; +/* This version of the event doesn't report the HDT rates */ + qos->ucast.in.rates =0x0000 ; + qos->ucast.out.rates =0x0000 ; + pending =test_and_clear_bit (HCI_CONN_CREATE_CIS , conn->flags);/* BLUETOOTH CORE SPECIFICATION Version 5.4 | Vol 6, Part G
@@ -7564,7 +7568,7 @@ static int hci_iso_term_big_sync(struct hci_dev *hdev, void *data)static void hci_le_create_big_complete (struct hci_dev *hdev,u8 status,u8 handle,u8 num_bis, -const __le16 *bis_handle) +const __le16 *bis_handle,u16 rates) {struct hci_conn *conn;__u8 i =0 ;
@@ -7606,6 +7610,7 @@ static void hci_le_create_big_complete(struct hci_dev *hdev, u8 status, } conn->state =BT_CONNECTED ; + conn->iso_qos.bcast.out.rates = rates;set_bit (HCI_CONN_BIG_CREATED , conn->flags);hci_debugfs_create_conn (conn);hci_conn_add_sysfs (conn);
@@ -7639,7 +7644,7 @@ static void hci_le_create_big_complete_evt(struct hci_dev *hdev, void *data,return ;hci_le_create_big_complete (hdev, ev->status, ev->handle, ev->num_bis, - ev->bis_handle); + ev->bis_handle,0x0000 ); } static void hci_le_big_sync_established_evt(struct hci_dev *hdev, void *data,
@@ -7895,7 +7900,7 @@ static void hci_le_cis_established_evt_v3(struct hci_dev *hdev, void *data, {struct hci_evt_le_cis_established_v3 *ev = data;struct hci_conn *conn; -struct bt_iso_qos *qos; +struct bt_iso_qos_ext *qos;bool pending = false;u16 handle =__le16_to_cpu (ev->handle);u32 c_sdu_interval, p_sdu_interval;
@@ -7941,6 +7946,8 @@ static void hci_le_cis_established_evt_v3(struct hci_dev *hdev, void *data, qos->ucast.out.sdu = ev->p_bn ?le16_to_cpu (ev->p_sdu) :0 ; qos->ucast.in.phys =le_phy_qos (ev->c_phy); qos->ucast.out.phys =le_phy_qos (ev->p_phy); + qos->ucast.in.rates =le16_to_cpu (ev->c_rates); + qos->ucast.out.rates =le16_to_cpu (ev->p_rates);break ;case HCI_ROLE_MASTER : qos->ucast.in.interval = p_sdu_interval;
@@ -7956,6 +7963,8 @@ static void hci_le_cis_established_evt_v3(struct hci_dev *hdev, void *data, qos->ucast.in.sdu = ev->p_bn ?le16_to_cpu (ev->p_sdu) :0 ; qos->ucast.out.phys =le_phy_qos (ev->c_phy); qos->ucast.in.phys =le_phy_qos (ev->p_phy); + qos->ucast.out.rates =le16_to_cpu (ev->c_rates); + qos->ucast.in.rates =le16_to_cpu (ev->p_rates);break ; }
@@ -7990,7 +7999,8 @@ static void hci_le_create_big_complete_v2_evt(struct hci_dev *hdev, void *data,return ;hci_le_create_big_complete (hdev, ev->status, ev->handle, ev->num_bis, - ev->bis_handle); + ev->bis_handle, +le16_to_cpu (ev->rates)); }#define HCI_LE_EV_VL (_op, _func, _min_len, _max_len) \
net/bluetooth/hci_sync.c +20 -12
@@ -3187,7 +3187,7 @@ static int hci_le_set_ext_scan_param_sync(struct hci_dev *hdev, u8 type, conn =hci_conn_hash_lookup_ba (hdev,PA_LINK , &bdaddr);if (conn) { -struct bt_iso_qos *qos = &conn->iso_qos; +struct bt_iso_qos_ext *qos = &conn->iso_qos;if (qos->bcast.in.phys &BT_ISO_PHY_1M || qos->bcast.in.phys &BT_ISO_PHY_2M ) {
@@ -7881,7 +7881,7 @@ static void create_pa_complete(struct hci_dev *hdev, void *data, int err) }static int hci_le_past_params_sync (struct hci_dev *hdev,struct hci_conn *conn, -u16 acl_handle,struct bt_iso_qos *qos) +u16 acl_handle,struct bt_iso_qos_ext *qos) {struct hci_cp_le_past_params cp;int err;
@@ -7915,7 +7915,7 @@ static int hci_le_pa_create_sync(struct hci_dev *hdev, void *data) {struct hci_cp_le_pa_create_sync cp;struct hci_conn *conn = data, *le; -struct bt_iso_qos *qos = &conn->iso_qos; +struct bt_iso_qos_ext *qos = &conn->iso_qos;int err;if (!hci_conn_valid (hdev, conn))
@@ -8056,7 +8056,7 @@ static int hci_le_big_create_sync(struct hci_dev *hdev, void *data) DEFINE_FLEX(struct hci_cp_le_big_create_sync, cp, bis, num_bis, HCI_MAX_ISO_BIS);struct hci_conn *conn = data; -struct bt_iso_qos *qos = &conn->iso_qos; +struct bt_iso_qos_ext *qos = &conn->iso_qos;int err;if (!hci_conn_valid (hdev, conn))
@@ -8413,7 +8413,7 @@ static int hci_le_set_cig_params_v2_sync(struct hci_dev *hdev, u8 cig_id) DEFINE_FLEX(struct hci_cp_le_set_cig_params_v2, pdu, cis, num_cis, HCI_LE_CIG_PARAMS_V2_MAX_CIS);struct hci_conn *conn; -struct bt_iso_qos *qos; +struct bt_iso_qos_ext *qos;u8 aux_num_cis =0 ;u8 cis_id;
@@ -8460,11 +8460,16 @@ static int hci_le_set_cig_params_v2_sync(struct hci_dev *hdev, u8 cig_id) cis->c_rtn = qos->ucast.out.rtn; cis->p_rtn = qos->ucast.in.rtn; +/* Use the rates of each direction, or all the HDT rates the +* controller supports if none were set. +*/ if (cis->c_phys &HCI_LE_SET_PHY_HDT ) - cis->c_hdt_rates =cpu_to_le16 (hci_hdt_tx_rates (hdev)); + cis->c_hdt_rates =cpu_to_le16 (qos->ucast.out.rates ? : +hci_hdt_tx_rates (hdev));if (cis->p_phys &HCI_LE_SET_PHY_HDT ) - cis->p_hdt_rates =cpu_to_le16 (hci_hdt_rx_rates (hdev)); + cis->p_hdt_rates =cpu_to_le16 (qos->ucast.in.rates ? : +hci_hdt_rx_rates (hdev)); } pdu->num_cis = aux_num_cis;
@@ -8483,7 +8488,7 @@ int hci_le_set_cig_params_sync(struct hci_dev *hdev, u8 cig_id) { DEFINE_FLEX(struct hci_cp_le_set_cig_params, pdu, cis, num_cis, 0x1f);struct hci_conn *conn; -struct bt_iso_qos *qos; +struct bt_iso_qos_ext *qos;u8 aux_num_cis =0 ;u8 cis_id;
@@ -8546,7 +8551,7 @@ int hci_le_set_cig_params_sync(struct hci_dev *hdev, u8 cig_id) }static int hci_le_create_big_v2_sync (struct hci_conn *conn, -struct bt_iso_qos *qos,u8 num_bis) +struct bt_iso_qos_ext *qos,u8 num_bis) {struct hci_dev *hdev = conn->hdev;struct hci_cp_le_create_big_v2 cp;
@@ -8565,15 +8570,18 @@ static int hci_le_create_big_v2_sync(struct hci_conn *conn, cp.bis.encryption = qos->bcast.encryption;memcpy (cp.bis.bcode, qos->bcast.bcode,sizeof (cp.bis.bcode)); -/* Check if HDT PHY is set then enable HDT supported rates */ +/* Use the rates set, or all the HDT rates the controller supports if +* none were set. +*/ if (cp.bis.phys &HCI_LE_SET_PHY_HDT ) - cp.bis.hdt_rates =cpu_to_le16 (hci_hdt_tx_rates (hdev)); + cp.bis.hdt_rates =cpu_to_le16 (qos->bcast.out.rates ? : +hci_hdt_tx_rates (hdev));return __hci_cmd_sync_status (hdev,HCI_OP_LE_CREATE_BIG_V2 ,sizeof (cp), &cp,HCI_CMD_TIMEOUT ); } -int hci_le_create_big_sync (struct hci_conn *conn,struct bt_iso_qos *qos, +int hci_le_create_big_sync (struct hci_conn *conn,struct bt_iso_qos_ext *qos,u8 num_bis) {struct hci_dev *hdev = conn->hdev;
net/bluetooth/iso.c +245 -17
367 lines not on this page · raw message
Signature · 1 line
2.56.0
Luiz Augusto von Dentz
maintainerPATCH v8 3/6 Bluetooth: Add initial support for EKS
In reply to Luiz Augusto von DentzFrom: Luiz Augusto von Dentz <[email protected]>
Add support for Encryption Key Schedule (EKS) introduced in Bluetooth 7.0:
- LE Enable Encryption v2, which replaces LE Start Encryption on EKS capable controllers and carries the MIC length to use on the LE HDT PHY. SMP now starts encryption through hci_le_enable_encrypt(), which picks the version the controller supports, outside of the RCU read-side section since queueing the command may sleep. If it can't be queued SMP fails the pairing or doesn't consider the encryption started. A Command Status error disconnects the link as it does for LE Start Encryption, and so does a command that fails without one, such as one that couldn't be sent. The Command Status error of LE Start Encryption now also clears the pending encryption, so the two don't both act on it. The command, which carries the key, is freed with kfree_sensitive().
- Encryption Change v3 and Encryption Key Refresh Complete v2, enabled through Event Mask Page 2, which report the MIC length and whether the key schedule is in use. The encryption change and key refresh handling is moved to helpers shared by every version of the events.
- eks_capable() for the Encryption Key Schedule feature bit.
--- include/net/bluetooth/hci.h | 30 +++++ include/net/bluetooth/hci_core.h | 4 +- include/net/bluetooth/hci_sync.h | 3 + net/bluetooth/hci_conn.c | 18 --- net/bluetooth/hci_event.c | 213 ++++++++++++++++++++++--------- net/bluetooth/hci_sync.c | 135 ++++++++++++++++++++ net/bluetooth/smp.c | 67 +++++++--- 7 files changed, 375 insertions(+), 95 deletions(-)
include/net/bluetooth/hci.h +30 -0
@@ -2564,6 +2564,16 @@ struct hci_rp_le_read_def_data_len_v2 {__le16 tx_time; } __packed; +#define HCI_OP_LE_ENABLE_ENCRYPT_V2 0x20af +struct hci_cp_le_enable_encrypt_v2 { +__le16 handle; +__le64 rand; +__le16 ediv; +__u8 ltk[16 ]; +__u8 mic_len; +__u8 encryption; +} __packed; +#define HCI_OP_LE_READ_MAX_DATA_LEN_V2 0x20b0struct hci_cp_le_read_max_data_len_v2 {__u8 phy;
@@ -3039,6 +3049,26 @@ struct hci_ev_sync_train_complete {#define HCI_EV_PERIPHERAL_PAGE_RESP_TIMEOUT 0x54 +#define HCI_EVT_KEY_REFRESH_COMPLETE_V2 0x5b +struct hci_evt_key_refresh_complete_v2 { +__u8 status; +__le16 handle; +__u8 mic_len; +__u8 eks_mode; +__u8 eks_debug; +} __packed; + +#define HCI_EVT_ENCRYPT_CHANGE_V3 0x5a +struct hci_evt_encrypt_change_v3 { +__u8 status; +__le16 handle; +__u8 mode; +__u8 key_size; +__u8 mic_len; +__u8 eks_mode; +__u8 eks_debug; +} __packed; +#define HCI_EV_LE_CONN_COMPLETE 0x01struct hci_ev_le_conn_complete {__u8 status;
include/net/bluetooth/hci_core.h +2 -2
@@ -2178,6 +2178,8 @@ void hci_conn_del_sysfs(struct hci_conn *conn); (le_feature(dev, 1, 2) & HCI_LE_HDT_7_5_TX_FEATURE)#define hdt_pf1_capable (dev) \ (le_feature(dev, 1, 2) & HCI_LE_HDT_PF_1) +#define eks_capable (dev) \ + (le_feature(dev, 1, 1) & HCI_LE_EKS_FEATURE)/* Channel sounding support */ #define le_cs_capable (dev) \
@@ -2625,8 +2627,6 @@ void mgmt_conn_subrate_notify(struct hci_dev *hdev, struct hci_conn *conn,int hci_abort_conn (struct hci_conn *conn,u8 reason);void hci_le_conn_update (struct hci_conn *conn,u16 min,u16 max,u16 latency,u16 to_multiplier); -void hci_le_start_enc (struct hci_conn *conn,__le16 ediv,__le64 rand, -__u8 ltk[16 ],__u8 key_size);void hci_copy_identity_address (struct hci_dev *hdev,bdaddr_t *bdaddr,u8 *bdaddr_type);
include/net/bluetooth/hci_sync.h +3 -0
@@ -197,3 +197,6 @@ int hci_le_set_phy(struct hci_conn *conn, u8 tx_phys, u8 rx_phys, u16 phy_opts);int hci_le_set_cig_params_sync (struct hci_dev *hdev,u8 cig_id);int hci_le_create_big_sync (struct hci_conn *conn,struct bt_iso_qos_ext *qos,u8 num_bis); + +int hci_le_enable_encrypt (struct hci_conn *conn,__le16 ediv,__le64 rand, +__u8 ltk[16 ],__u8 key_size);
net/bluetooth/hci_conn.c +0 -18
@@ -598,24 +598,6 @@ void hci_le_conn_update(struct hci_conn *conn, u16 min, u16 max, u16 latency, } } -void hci_le_start_enc (struct hci_conn *conn,__le16 ediv,__le64 rand, -__u8 ltk[16 ],__u8 key_size) -{ -struct hci_dev *hdev = conn->hdev; -struct hci_cp_le_start_enc cp; - -BT_DBG ("hcon %p" , conn); - -memset (&cp,0 ,sizeof (cp)); - - cp.handle =cpu_to_le16 (conn->handle); - cp.rand = rand; - cp.ediv = ediv; -memcpy (cp.ltk, ltk, key_size); - -hci_send_cmd (hdev,HCI_OP_LE_START_ENC ,sizeof (cp), &cp); -} -/* Device _must_ be locked */ void hci_sco_setup (struct hci_conn *conn,__u8 status) {
net/bluetooth/hci_event.c +155 -58
300 lines not on this page · raw message
net/bluetooth/hci_sync.c +135 -0
150 lines not on this page · raw message
net/bluetooth/smp.c +50 -17
100 lines not on this page · raw message
Signature · 1 line
2.56.0
Luiz Augusto von Dentz
maintainerPATCH v8 4/6 Bluetooth: L2CAP: Add MIC length validation for HDT PHY
In reply to Luiz Augusto von DentzFrom: Luiz Augusto von Dentz <[email protected]>
Add a mic_len field to struct bt_security so userspace can require a minimum MIC length on an L2CAP channel with BT_SECURITY, and read the MIC length in use on the link back. The field is added at the end of the struct, so the shorter struct is still accepted by L2CAP and RFCOMM, leaving mic_len unset, and values other than 32, 64 and 128 bits are rejected.
The MIC length a channel requires is requested on the connection on every path starting LE security, so LE Enable Encryption v2 asks for it, while the MIC length the controller reports with Encryption Change v3 and Encryption Key Refresh Complete v2 is kept separately, so a request never stands for what is in use. When a connection is encrypted on the LE HDT PHY with a MIC shorter than the channel requires, the LE Credit Based and Enhanced Credit Based connection requests are rejected with MIC Length Too Short.
The reported MIC length only applies on the LE HDT PHY, the MIC is always 32 bits on the GFSK PHYs, so hci_conn_mic_len() reports it as such both for the check and for BT_SECURITY.
--- include/net/bluetooth/bluetooth.h | 1 + include/net/bluetooth/hci_core.h | 9 ++++++ include/net/bluetooth/l2cap.h | 7 ++++ net/bluetooth/hci_event.c | 19 +++++++++-- net/bluetooth/hci_sync.c | 15 +++++++-- net/bluetooth/l2cap_core.c | 54 ++++++++++++++++++++++++++++++- net/bluetooth/l2cap_sock.c | 23 +++++++++++-- net/bluetooth/rfcomm/sock.c | 13 ++++++-- 8 files changed, 129 insertions(+), 12 deletions(-)
include/net/bluetooth/bluetooth.h +1 -0
@@ -66,6 +66,7 @@struct bt_security {__u8 level;__u8 key_size; +__u8 mic_len; };#define BT_SECURITY_SDP 0#define BT_SECURITY_LOW 1
include/net/bluetooth/hci_core.h +9 -0
@@ -765,6 +765,8 @@ struct hci_conn {__u8 pending_sec_level;__u8 pin_length;__u8 enc_key_size; +__u8 mic_len; +__u8 req_mic_len;__u8 io_capability;__u32 passkey_notify;__u8 passkey_entered;
@@ -2178,6 +2180,13 @@ void hci_conn_del_sysfs(struct hci_conn *conn); (le_feature(dev, 1, 2) & HCI_LE_HDT_7_5_TX_FEATURE)#define hdt_pf1_capable (dev) \ (le_feature(dev, 1, 2) & HCI_LE_HDT_PF_1) +/* The MIC length reported by the controller only applies on the LE HDT PHY, +* the MIC is always 32 bits (0x00) on the GFSK PHYs. +*/ +static inline __u8 hci_conn_mic_len (struct hci_conn *conn) +{ +return conn->le_rx_phy ==0x05 ? conn->mic_len :0x00 ; +}#define eks_capable (dev) \ (le_feature(dev, 1, 1) & HCI_LE_EKS_FEATURE)
include/net/bluetooth/l2cap.h +7 -0
@@ -285,6 +285,11 @@ struct l2cap_conn_rsp {#define L2CAP_CR_LE_SCID_IN_USE 0x000A#define L2CAP_CR_LE_UNACCEPT_PARAMS 0x000B#define L2CAP_CR_LE_INVALID_PARAMS 0x000C +/* MIC Length Too Short has a different value in each response: the LE Credit +* Based value is Invalid Parameters in the Enhanced Credit Based one. +*/ +#define L2CAP_CR_LE_MIC_LEN_TOO_SHORT 0x000C +#define L2CAP_CR_ECRED_MIC_LEN_TOO_SHORT 0x0010/* connect/create channel status */ #define L2CAP_CS_NO_INFO 0x0000
@@ -533,6 +538,7 @@ struct l2cap_chan {__u8 chan_policy;__u8 sec_level; +__u8 mic_len;__u8 ident;
@@ -981,6 +987,7 @@ int l2cap_chan_send(struct l2cap_chan *chan, struct msghdr *msg, size_t len, const struct sockcm_cookie *sockc);void l2cap_chan_busy (struct l2cap_chan *chan,int busy);void l2cap_chan_rx_avail (struct l2cap_chan *chan,ssize_t rx_avail); +void l2cap_chan_req_mic_len (struct l2cap_chan *chan,struct hci_conn *hcon);int l2cap_chan_check_security (struct l2cap_chan *chan,bool initiator);void l2cap_chan_set_defaults (struct l2cap_chan *chan,struct l2cap_chan *pchan);int l2cap_ertm_init (struct l2cap_chan *chan);
net/bluetooth/hci_event.c +16 -3
@@ -3762,7 +3762,8 @@ static void hci_remote_name_evt(struct hci_dev *hdev, void *data,hci_dev_unlock (hdev); } -static void hci_change_encrypt (struct hci_conn *conn,u8 status,u8 encrypt) +static void hci_change_encrypt (struct hci_conn *conn,u8 status,u8 encrypt, +u8 mic_len) {struct hci_dev *hdev = conn->hdev;
@@ -3781,6 +3782,14 @@ static void hci_change_encrypt(struct hci_conn *conn, u8 status, u8 encrypt) conn->type == LE_LINK)set_bit (HCI_CONN_AES_CCM , conn->flags); +/* The key size of Encryption Change v3 is not used: +* it is ignored for LE, where it comes from SMP, and +* the ACL key size is read below. +* +* A 32-bit MIC is reported as 0x00. +*/ + conn->mic_len = mic_len; +/* For ACL links the encryption key size is still * validated below via hci_read_enc_key_size(). Its * completion handler, hci_cc_read_enc_key_size(),
@@ -3890,7 +3899,7 @@ static void hci_encrypt_change_evt(struct hci_dev *hdev, void *data,if (!conn) goto unlock; -hci_change_encrypt (conn, ev->status, ev->encrypt); +hci_change_encrypt (conn, ev->status, ev->encrypt,0 ); unlock:hci_dev_unlock (hdev);
@@ -3910,7 +3919,7 @@ static void hci_encrypt_change_v3_evt(struct hci_dev *hdev, void *data,if (!conn) goto unlock; -hci_change_encrypt (conn, ev->status, ev->mode); +hci_change_encrypt (conn, ev->status, ev->mode, ev->mic_len); unlock:hci_dev_unlock (hdev);
@@ -5696,6 +5705,10 @@ static void hci_key_refresh_complete_v2_evt(struct hci_dev *hdev, void *data,if (!conn) goto unlock; +/* The key refresh may change the MIC length */ +if (!ev->status) + conn->mic_len = ev->mic_len; +hci_conn_refresh_key (conn, ev->status); unlock:
net/bluetooth/hci_sync.c +13 -2
@@ -8654,8 +8654,21 @@ static void le_enable_encrypt_failed(struct hci_dev *hdev, __le16 handle)static int hci_le_enable_encrypt_v2_sync (struct hci_dev *hdev,void *data) {struct hci_cp_le_enable_encrypt_v2 *cp = data; +struct hci_conn *conn;int err; +/* Use the MIC length requested by the time the command is sent, as +* channels may still raise it after it was queued, defaulting to 128 +* bits if unset. +*/ +hci_dev_lock (hdev); + + conn =hci_conn_hash_lookup_handle (hdev,le16_to_cpu (cp->handle)); +if (conn) + cp->mic_len = conn->req_mic_len ? conn->req_mic_len :0x02 ; + +hci_dev_unlock (hdev); + err =__hci_cmd_sync_status (hdev,HCI_OP_LE_ENABLE_ENCRYPT_V2 ,sizeof (*cp), cp,HCI_CMD_TIMEOUT );if (err)
@@ -8680,8 +8693,6 @@ static int hci_le_enable_encrypt_v2(struct hci_conn *conn, __le16 ediv, cp->handle =cpu_to_le16 (conn->handle); cp->rand = rand; cp->ediv = ediv; - cp->mic_len =0x02 ;/* Always prefer 128 bits? */ -/* The key is zero padded when shorter than 16 octets */ if (ltk) {memcpy (cp->ltk, ltk, key_size);
net/bluetooth/l2cap_core.c +53 -1
121 lines not on this page · raw message
net/bluetooth/l2cap_sock.c +20 -3
@@ -623,8 +623,10 @@ static int l2cap_sock_getsockopt(struct socket *sock, int level, int optname,if (conn) { sec.level = conn->hcon->sec_level; -if (sk->sk_state ==BT_CONNECTED ) +if (sk->sk_state ==BT_CONNECTED ) { sec.key_size = conn->hcon->enc_key_size; + sec.mic_len =hci_conn_mic_len (conn->hcon); + } }else { sec.level = chan->sec_level; }
@@ -960,9 +962,16 @@ static int l2cap_sock_setsockopt(struct socket *sock, int level, int optname,break ; } - sec.level =BT_SECURITY_LOW ; +/* mic_len was added at the end of struct bt_security, so +* accept the shorter struct as well, leaving mic_len unset. +*/ + if (optlen < offsetofend(struct bt_security, key_size)) { + err = -EINVAL ; +break ; + } - err =copy_safe_from_sockptr (&sec,sizeof (sec), optval, optlen); + err =copy_struct_from_sockptr (&sec,sizeof (sec), optval, + optlen);if (err)break ;
@@ -972,7 +981,14 @@ static int l2cap_sock_setsockopt(struct socket *sock, int level, int optname,break ; } +/* MIC_Length values: 32, 64 and 128 bits */ +if (sec.mic_len >0x02 ) { + err = -EINVAL ; +break ; + } + chan->sec_level = sec.level; + chan->mic_len = sec.mic_len; conn =l2cap_chan_conn (chan);if (!conn)
@@ -980,6 +996,7 @@ static int l2cap_sock_setsockopt(struct socket *sock, int level, int optname,/* change security for LE channels */ if (chan->scid ==L2CAP_CID_ATT ) { +l2cap_chan_req_mic_len (chan, conn->hcon);if (smp_conn_security (conn->hcon, sec.level)) { err = -EINVAL ;break ;
net/bluetooth/rfcomm/sock.c +10 -3
@@ -700,9 +700,16 @@ static int rfcomm_sock_setsockopt(struct socket *sock, int level, int optname,break ; } - sec.level =BT_SECURITY_LOW ; +/* mic_len was added at the end of struct bt_security, so +* accept the shorter struct as well. RFCOMM ignores it. +*/ + if (optlen < offsetofend(struct bt_security, key_size)) { + err = -EINVAL ; +break ; + } - err =copy_safe_from_sockptr (&sec,sizeof (sec), optval, optlen); + err =copy_struct_from_sockptr (&sec,sizeof (sec), optval, + optlen);if (err)break ;
@@ -844,8 +851,8 @@ static int rfcomm_sock_getsockopt(struct socket *sock, int level, int optname,break ; } +memset (&sec,0 ,sizeof (sec)); sec.level =rfcomm_pi (sk)->sec_level; - sec.key_size =0 ; len =min (len,sizeof (sec));if (copy_to_iter (&sec, len, &sopt->iter_out) != len)
Signature · 1 line
2.56.0
Luiz Augusto von Dentz
maintainerPATCH v8 5/6 Bluetooth: Add HCI_OP_LE_SET_HDT_DEFAULT_PARAMS support
In reply to Luiz Augusto von DentzFrom: Luiz Augusto von Dentz <[email protected]>
Add support for LE Set HDT Default Parameters, which sets the MIC length, packet format and ACL rates the controller prefers on the LE HDT PHY. The command is sent during controller initialization when the controller supports HDT and the command, with the rates limited to the ones the controller supports.
The defaults are stored in hci_dev, 128-bit MIC, no packet format preference and all HDT rates, and exposed through the MGMT system configuration TLVs 0x0021-0x0023 so userspace can change them; changing them while the controller is up sends the command again.
The default MIC length applies when the connection did not request
one: to LE Enable Encryption v2, LE Set CIG Parameters v2 and LE Create BIG v2, so ACL, CIS and BIS are set up with the MIC length the host was told to use.
--- include/net/bluetooth/hci.h | 7 ++++++ include/net/bluetooth/hci_core.h | 3 +++ include/net/bluetooth/hci_sync.h | 2 ++ net/bluetooth/hci_core.c | 3 +++ net/bluetooth/hci_sync.c | 41 ++++++++++++++++++++++++++++---- net/bluetooth/mgmt_config.c | 33 +++++++++++++++++++++++++ 6 files changed, 85 insertions(+), 4 deletions(-)
include/net/bluetooth/hci.h +7 -0
@@ -2663,6 +2663,13 @@ struct hci_cp_le_create_big_v2 {struct hci_bis_v2 bis; } __packed; +#define HCI_OP_LE_SET_HDT_DEFAULT_PARAMS 0x20bc +struct hci_cp_le_set_hdt_default_params { +__u8 mic_len; +__u8 format; +__le16 rates; +} __packed; +/* ---- HCI Events ---- */ struct hci_ev_status {__u8 status;
include/net/bluetooth/hci_core.h +3 -0
@@ -433,6 +433,9 @@ struct hci_dev {__u8 hdt_max_tx_win;__u8 hdt_max_rx_win;__u16 hdt_max_rx_packet; +__u8 hdt_def_mic_len; +__u8 hdt_def_format; +__u16 hdt_def_rates;__u8 le_max_key_size;__u8 le_min_key_size;__u16 discov_interleaved_timeout;
include/net/bluetooth/hci_sync.h +2 -0
@@ -198,5 +198,7 @@ int hci_le_set_cig_params_sync(struct hci_dev *hdev, u8 cig_id);int hci_le_create_big_sync (struct hci_conn *conn,struct bt_iso_qos_ext *qos,u8 num_bis); +int hci_le_set_hdt_params_sync (struct hci_dev *hdev); +int hci_le_enable_encrypt (struct hci_conn *conn,__le16 ediv,__le64 rand,__u8 ltk[16 ],__u8 key_size);
net/bluetooth/hci_core.c +3 -0
@@ -2575,6 +2575,9 @@ struct hci_dev *hci_alloc_dev_priv(int sizeof_priv) hdev->le_min_key_size =SMP_MIN_ENC_KEY_SIZE ; hdev->le_tx_def_phys =HCI_LE_SET_PHY_1M ; hdev->le_rx_def_phys =HCI_LE_SET_PHY_1M ; + hdev->hdt_def_mic_len =0x02 ;/* 128-bit */ + hdev->hdt_def_format =0x00 ;/* No preference */ + hdev->hdt_def_rates =0x001f ;/* All defined HDT rates */ hdev->le_num_of_adv_sets =HCI_MAX_ADV_INSTANCES ; hdev->def_multi_adv_rotation_duration =HCI_DEFAULT_ADV_DURATION ; hdev->def_le_autoconnect_timeout =HCI_LE_CONN_TIMEOUT ;
net/bluetooth/hci_sync.c +37 -4
75 lines not on this page · raw message
net/bluetooth/mgmt_config.c +33 -0
@@ -91,6 +91,9 @@ int read_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data,HDEV_PARAM_U16 (advmon_no_filter_duration);HDEV_PARAM_U8 (enable_advmon_interleave_scan);HDEV_PARAM_U32 (idle_timeout); +HDEV_PARAM_U8 (hdt_def_mic_len); +HDEV_PARAM_U8 (hdt_def_format); +HDEV_PARAM_U16 (hdt_def_rates); }__packed rp = {TLV_SET_U16 (0x0000 , def_page_scan_type),TLV_SET_U16 (0x0001 , def_page_scan_int),
@@ -125,6 +128,9 @@ int read_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data,TLV_SET_U16 (0x001e , advmon_no_filter_duration),TLV_SET_U8 (0x001f , enable_advmon_interleave_scan),TLV_SET_U32 (0x0020 , idle_timeout), +TLV_SET_U8 (0x0021 , hdt_def_mic_len), +TLV_SET_U8 (0x0022 , hdt_def_format), +TLV_SET_U16 (0x0023 , hdt_def_rates), };bt_dev_dbg (hdev,"sock %p" , sk);
@@ -140,11 +146,19 @@ int read_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data,#define TLV_GET_LE16 (tlv) le16_to_cpu(*((__le16 *)(TO_TLV(tlv)->value)))#define TLV_GET_U8 (tlv) (*((__u8 *)(TO_TLV(tlv)->value))) +static int set_hdt_params_sync (struct hci_dev *hdev,void *data) +{ +return hci_le_set_hdt_params_sync (hdev); +} +int set_def_system_config (struct sock *sk,struct hci_dev *hdev,void *data,u16 data_len) {u16 buffer_left = data_len;u8 *buffer = data; +u8 old_mic_len = hdev->hdt_def_mic_len; +u8 old_format = hdev->hdt_def_format; +u16 old_rates = hdev->hdt_def_rates;if (buffer_left <sizeof (struct mgmt_tlv )) { return mgmt_cmd_status(sk, hdev->id,
@@ -201,9 +215,12 @@ int set_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data,case 0x001b :case 0x001d :case 0x001e : +case 0x0023 : exp_type_len =sizeof (u16);break ;case 0x001f : +case 0x0021 : +case 0x0022 : exp_type_len =sizeof (u8);break ;case 0x0020 :
@@ -335,6 +352,15 @@ int set_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data,case 0x00020 : hdev->idle_timeout =TLV_GET_LE32 (buffer);break ; +case 0x0021 : + hdev->hdt_def_mic_len =TLV_GET_U8 (buffer); +break ; +case 0x0022 : + hdev->hdt_def_format =TLV_GET_U8 (buffer); +break ; +case 0x0023 : + hdev->hdt_def_rates =TLV_GET_LE16 (buffer); +break ;default :bt_dev_warn (hdev,"unsupported parameter %u" , type);break ;
@@ -344,6 +370,13 @@ int set_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data, buffer += exp_len; } +/* The controller may be up without being powered through MGMT */ +if (test_bit (HCI_UP , &hdev->flags) && + (hdev->hdt_def_mic_len != old_mic_len || + hdev->hdt_def_format != old_format || + hdev->hdt_def_rates != old_rates)) +hci_cmd_sync_queue (hdev, set_hdt_params_sync,NULL ,NULL ); +return mgmt_cmd_complete (sk, hdev->id,MGMT_OP_SET_DEF_SYSTEM_CONFIG ,0 ,NULL ,0 ); }
Signature · 1 line
2.56.0
Luiz Augusto von Dentz
maintainerPATCH v8 6/6 Bluetooth: Add EKS Opportunistic Encryption support
In reply to Luiz Augusto von DentzFrom: Luiz Augusto von Dentz <[email protected]>
Add support for opportunistic encryption with Encryption Key Schedule, which encrypts a link without pairing when both devices support it:
- The Opportunistic Encryption (Host Support) feature bit (Link Layer feature bit 90) is set with LE Set Host Feature during initialization, and eks_oppt_capable() checks the remote supports it.
- When the remote features are read as Central and there is no LTK for the peer, LE Enable Encryption v2 is sent with Encryption set to opportunistic. The checks are repeated right before the command is sent, so it is skipped if the link is gone, already encrypted, has SMP encryption pending or SMP pairing has started in the meantime, and the MIC length is taken at that point so the one requested by L2CAP is used.
- The new HCI_CONN_OPP_ENCRYPT flag marks the request in flight and, once Encryption Change v3 reports it, an opportunistically encrypted link, which is also marked as encrypted with AES-CCM. It doesn't raise the security level, as it is not authenticated, and since it has no key from pairing the L2CAP key size check is skipped for it. A failure, or a command that cannot be sent, just leaves the link unencrypted, as it was. Since opportunistic encryption can only be started on an unencrypted link, reporting it for a link with a key from pairing is a downgrade, which disconnects the link. A failure on an opportunistically encrypted link is handled as for any encrypted link, without the encryption flags it had.
- SMP only distributes keys once a key from pairing encrypts the link, not on opportunistic encryption.
- HCI_CONN_ENCRYPT_PEND is not used for opportunistic encryption, so it doesn't block SMP. Pairing over such a link completes: the Key Refresh Complete of its key clears HCI_CONN_OPP_ENCRYPT and is handled as Encryption Change is for an unencrypted link.
- A Key Refresh Complete reporting opportunistic encryption, such as one changing the MIC length, keeps the link opportunistically encrypted. Opportunistic encryption can only be started on an unencrypted link, so on a link with a key from pairing it would be a downgrade, which disconnects the link.
- The feature can be turned off with the MGMT system configuration TLV 0x0024; it is on by default. Changing it while the controller is up updates the feature bit, which the controller only allows when there are no connections.
--- include/net/bluetooth/hci.h | 1 + include/net/bluetooth/hci_core.h | 6 ++ include/net/bluetooth/hci_sync.h | 2 + net/bluetooth/hci_core.c | 1 + net/bluetooth/hci_event.c | 93 +++++++++++++++++++- net/bluetooth/hci_sync.c | 142 ++++++++++++++++++++++++++++++- net/bluetooth/l2cap_core.c | 6 ++ net/bluetooth/mgmt_config.c | 23 +++++ net/bluetooth/smp.c | 29 ++++++- net/bluetooth/smp.h | 2 + 10 files changed, 297 insertions(+), 8 deletions(-)
include/net/bluetooth/hci.h +1 -0
@@ -668,6 +668,7 @@ enum {#define HCI_LE_HDT_7_5_TX_FEATURE BIT(1)#define HCI_LE_HDT_PF_1 BIT(2)#define HCI_LE_HDT_LQF_FEATURE BIT(3) +#define HCI_LE_OPPORTUNISTIC_ENC BIT(2)/* Byte 3 */ /* Connection modes */ #define HCI_CM_ACTIVE 0x0000
include/net/bluetooth/hci_core.h +6 -0
@@ -436,6 +436,7 @@ struct hci_dev {__u8 hdt_def_mic_len;__u8 hdt_def_format;__u16 hdt_def_rates; +bool eks_oppt;__u8 le_max_key_size;__u8 le_min_key_size;__u16 discov_interleaved_timeout;
@@ -707,6 +708,7 @@ enum {HCI_CONN_POWER_SAVE ,HCI_CONN_FLUSH_KEY ,HCI_CONN_ENCRYPT , +HCI_CONN_OPP_ENCRYPT ,HCI_CONN_AUTH ,HCI_CONN_SECURE , HCI_CONN_FIPS,
@@ -2193,6 +2195,10 @@ static inline __u8 hci_conn_mic_len(struct hci_conn *conn)#define eks_capable (dev) \ (le_feature(dev, 1, 1) & HCI_LE_EKS_FEATURE) +#define eks_oppt_capable (dev) \ + (eks_capable(dev) && \ + (le_feature(dev, 1, 3) & HCI_LE_OPPORTUNISTIC_ENC)) +/* Channel sounding support */ #define le_cs_capable (dev) \ ((dev)->le_features[5] & HCI_LE_CS)
include/net/bluetooth/hci_sync.h +2 -0
@@ -202,3 +202,5 @@ int hci_le_set_hdt_params_sync(struct hci_dev *hdev);int hci_le_enable_encrypt (struct hci_conn *conn,__le16 ediv,__le64 rand,__u8 ltk[16 ],__u8 key_size); +int hci_le_eks_oppt_encrypt (struct hci_conn *conn); +int hci_le_set_eks_oppt_sync (struct hci_dev *hdev);
net/bluetooth/hci_core.c +1 -0
@@ -2578,6 +2578,7 @@ struct hci_dev *hci_alloc_dev_priv(int sizeof_priv) hdev->hdt_def_mic_len =0x02 ;/* 128-bit */ hdev->hdt_def_format =0x00 ;/* No preference */ hdev->hdt_def_rates =0x001f ;/* All defined HDT rates */ + hdev->eks_oppt = true;/* Opportunistic encryption enabled */ hdev->le_num_of_adv_sets =HCI_MAX_ADV_INSTANCES ; hdev->def_multi_adv_rotation_duration =HCI_DEFAULT_ADV_DURATION ; hdev->def_le_autoconnect_timeout =HCI_LE_CONN_TIMEOUT ;
net/bluetooth/hci_event.c +90 -3
120 lines not on this page · raw message
net/bluetooth/hci_sync.c +138 -4
172 lines not on this page · raw message
net/bluetooth/l2cap_core.c +6 -0
@@ -1583,6 +1583,11 @@ static bool l2cap_check_enc_key_size(struct hci_conn *hcon,* This check might also be called for unencrypted connections * that have no key size requirements. Ensure that the link is * actually encrypted before enforcing a key size. +* +* Opportunistic encryption has no key from pairing, so there is no +* key size to enforce. The security level stays as if the link were +* unencrypted, so a channel requiring more still needs pairing, +* which then replaces the opportunistic key. */ int min_key_size = hcon->hdev->min_enc_key_size;
@@ -1591,6 +1596,7 @@ static bool l2cap_check_enc_key_size(struct hci_conn *hcon, min_key_size =16 ;return (!test_bit (HCI_CONN_ENCRYPT , hcon->flags) || +test_bit (HCI_CONN_OPP_ENCRYPT , hcon->flags) || hcon->enc_key_size >= min_key_size); }
net/bluetooth/mgmt_config.c +23 -0
@@ -94,6 +94,7 @@ int read_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data,HDEV_PARAM_U8 (hdt_def_mic_len);HDEV_PARAM_U8 (hdt_def_format);HDEV_PARAM_U16 (hdt_def_rates); +HDEV_PARAM_U8 (eks_oppt); }__packed rp = {TLV_SET_U16 (0x0000 , def_page_scan_type),TLV_SET_U16 (0x0001 , def_page_scan_int),
@@ -131,6 +132,7 @@ int read_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data,TLV_SET_U8 (0x0021 , hdt_def_mic_len),TLV_SET_U8 (0x0022 , hdt_def_format),TLV_SET_U16 (0x0023 , hdt_def_rates), +TLV_SET_U8 (0x0024 , eks_oppt), };bt_dev_dbg (hdev,"sock %p" , sk);
@@ -151,6 +153,19 @@ static int set_hdt_params_sync(struct hci_dev *hdev, void *data)return hci_le_set_hdt_params_sync (hdev); } +static int set_eks_oppt_sync (struct hci_dev *hdev,void *data) +{ +int err; + +/* The controller doesn't allow it while there are connections */ + err =hci_le_set_eks_oppt_sync (hdev); +if (err) +bt_dev_warn (hdev,"unable to set opportunistic encryption: %d" , + err); + +return err; +} +int set_def_system_config (struct sock *sk,struct hci_dev *hdev,void *data,u16 data_len) {
@@ -159,6 +174,7 @@ int set_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data,u8 old_mic_len = hdev->hdt_def_mic_len;u8 old_format = hdev->hdt_def_format;u16 old_rates = hdev->hdt_def_rates; +bool old_eks_oppt = hdev->eks_oppt;if (buffer_left <sizeof (struct mgmt_tlv )) { return mgmt_cmd_status(sk, hdev->id,
@@ -221,6 +237,7 @@ int set_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data,case 0x001f :case 0x0021 :case 0x0022 : +case 0x0024 : exp_type_len =sizeof (u8);break ;case 0x0020 :
@@ -361,6 +378,9 @@ int set_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data,case 0x0023 : hdev->hdt_def_rates =TLV_GET_LE16 (buffer);break ; +case 0x0024 : + hdev->eks_oppt = !!TLV_GET_U8 (buffer); +break ;default :bt_dev_warn (hdev,"unsupported parameter %u" , type);break ;
@@ -377,6 +397,9 @@ int set_def_system_config(struct sock *sk, struct hci_dev *hdev, void *data, hdev->hdt_def_rates != old_rates))hci_cmd_sync_queue (hdev, set_hdt_params_sync,NULL ,NULL ); +if (test_bit (HCI_UP , &hdev->flags) && hdev->eks_oppt != old_eks_oppt) +hci_cmd_sync_queue (hdev, set_eks_oppt_sync,NULL ,NULL ); +return mgmt_cmd_complete (sk, hdev->id,MGMT_OP_SET_DEF_SYSTEM_CONFIG ,0 ,NULL ,0 ); }
net/bluetooth/smp.c +28 -1
@@ -2464,6 +2464,29 @@ int smp_conn_security(struct hci_conn *hcon, __u8 sec_level)return ret; } +bool smp_pairing_in_progress (struct hci_conn *hcon) +{ +struct l2cap_conn *conn; +struct l2cap_chan *chan; +bool pending; + +lockdep_assert_held (&hcon->hdev->lock); + + conn = hcon->l2cap_data; +if (!conn) +return false; + + chan = conn->smp; +if (!chan) +return false; + +l2cap_chan_lock (chan); + pending = !!chan->data; +l2cap_chan_unlock (chan); + +return pending; +} +int smp_cancel_and_remove_pairing (struct hci_dev *hdev,bdaddr_t *bdaddr,u8 addr_type) {
@@ -3195,7 +3218,11 @@ static void smp_resume_cb(struct l2cap_chan *chan)if (!smp)return ; -if (!test_bit (HCI_CONN_ENCRYPT , hcon->flags)) +/* Opportunistic encryption doesn't use a key from pairing, so keys +* are only distributed once the pairing encrypts the link. +*/ +if (!test_bit (HCI_CONN_ENCRYPT , hcon->flags) || +test_bit (HCI_CONN_OPP_ENCRYPT , hcon->flags))return ;cancel_delayed_work (&smp->security_timer);
net/bluetooth/smp.h +2 -0
@@ -185,6 +185,8 @@ int smp_cancel_and_remove_pairing(struct hci_dev *hdev, bdaddr_t *bdaddr,bool smp_sufficient_security (struct hci_conn *hcon,u8 sec_level,enum smp_key_pref key_pref);int smp_conn_security (struct hci_conn *hcon,__u8 sec_level); +bool smp_pairing_in_progress(struct hci_conn *hcon) + __must_hold(&hcon->hdev->lock); int smp_user_confirm_reply(struct hci_conn *conn, u16 mgmt_op, __le32 passkey) __must_hold(&conn->hdev->lock);
Signature · 1 line
2.56.0