Skip to contentSkip to conversation

arm64: dts: allwinner: h6: taiqicat-a01: Enable Ethernet

PATCH In review Jun Yan 3 participants 3 messages Nov 17

Subsystems (2)
lore
Share & tools
lore

Jun Yan

author
#0 lore raw

PATCH 1/1 arm64: dts: allwinner: h6: taiqicat-a01: Enable Ethernet

The TaiqiCat A01 has a 100 Mbit/s Ethernet port, which uses the EPHY integrated into the co-packaged AC200 of the Allwinner H6 SoC.

The AC200 derives its 24 MHz reference clock from PWM1, so enable the PWM controller and the pwm-clock node that supplies it. Also enable I2C3, over which the AC200 is accessed, and describe the AC200 EPHY package on the EMAC MDIO bus, with the EMAC operating in RMII mode.

---
The AC200 MFD and EPHY drivers/bindings and the sun50i-h6.dtsi AC200 description this depends on are already merged in sunxi/dt-for-7.5.

---
 .../dts/allwinner/sun50i-h6-taiqicat-a01.dts  | 40 +++++++++++++++++++
 1 file changed, 40 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6-taiqicat-a01.dts +40 -0
index 225f42bd3b9e..9b192caeecb2 100644
@@ -14,6 +14,7 @@ / {
 	compatible = "ultrapower,taiqicat-a01", "allwinner,sun50i-h6";
 
 	aliases {
+		ethernet0 = &emac;
 		ethernet1 = &sdio_wifi;
 		serial0 = &uart0;
 	};
@@ -87,6 +88,10 @@ wifi_pwrseq: wifi-pwrseq {
 	};
 };
 
+&ac200_clk {
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_dcdca>;
 };
@@ -107,6 +112,14 @@ &ehci3 {
 	status = "okay";
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rmii_pins>;
+	phy-mode = "rmii";
+	phy-handle = <&ac200_ephy>;
+	status = "okay";
+};
+
 &gpu {
 	mali-supply = <&reg_dcdcc>;
 	status = "okay";
@@ -123,6 +136,29 @@ hdmi_out_con: endpoint {
 	};
 };
 
+&i2c3 {
+	status = "okay";
+};
+
+&mdio {
+	ethernet-phy-package@1 {
+		compatible = "x-powers,ac200-ephy-package";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		vcc-supply = <&reg_aldo2>;
+		nvmem-cells = <&ephy_calibration>;
+		nvmem-cell-names = "configuration";
+		x-powers,ac200 = <&ac200>;
+		x-powers,xmii-rx-clock-inverted;
+
+		ac200_ephy: ethernet-phy@1 {
+			compatible = "ethernet-phy-id0044.1400";
+			reg = <1>;
+		};
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_cldo1>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
@@ -173,6 +209,10 @@ &pio {
 	vcc-pg-supply = <&reg_bldo3>;
 };
 
+&pwm {
+	status = "okay";
+};
+
 &r_i2c {
 	status = "okay";
 
Signature · 1 line
2.56.1
#1 lore raw
Thank you for your contribution! Sashiko AI review found 1 potential issue to consider: - [High] arm64: dts: allwinner: unresolved AC200 labels in sun50i-h6-taiqicat-a01.dts --

Thank you for your contribution! Sashiko AI review found 1 potential issue to consider:
- [High] arm64: dts: allwinner: unresolved AC200 labels in sun50i-h6-taiqicat-a01.dts
--

commit e13407bcadeb9e661561721128883210b4a0461e
Author: Jun Yan <[email protected]>

arm64: dts: allwinner: h6: taiqicat-a01: Enable Ethernet

This commit enables the EMAC, PWM, I2C3, and AC200 EPHY nodes in the TaiqiCat A01 device tree to support the onboard 100 Mbit/s Ethernet port.

Quoted 4 lines
arch/arm64/boot/dts/allwinner/sun50i-h6-taiqicat-a01.dts +0 -0
index 225f42bd3b9e5..9b192caeecb23 100644

[ ... ]

Quoted 42 lines
arch/arm64/boot/dts/allwinner/sun50i-h6-taiqicat-a01.dts +24 -0
@@ -87,6 +88,10 @@ wifi_pwrseq: wifi-pwrseq {
 	};
 };
 
+&ac200_clk {
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_dcdca>;
 };
@@ -107,6 +112,14 @@ &ehci3 {
 	status = "okay";
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rmii_pins>;
+	phy-mode = "rmii";
+	phy-handle = <&ac200_ephy>;
+	status = "okay";
+};
+
 &gpu {
 	mali-supply = <&reg_dcdcc>;
 	status = "okay";
@@ -123,6 +136,29 @@ hdmi_out_con: endpoint {
 	};
 };
 
+&i2c3 {
+	status = "okay";
+};
+
+&mdio {
+	ethernet-phy-package@1 {
+		compatible = "x-powers,ac200-ephy-package";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		vcc-supply = <&reg_aldo2>;
+		nvmem-cells = <&ephy_calibration>;

arch/arm64/boot/dts/allwinner/sun50i-h6-taiqicat-a01.dts hdmi_out_con: endpoint { · line 160

Quoted 10 lines
arch/arm64/boot/dts/allwinner/sun50i-h6-taiqicat-a01.dts +10 -0
+		nvmem-cell-names = "configuration";
+		x-powers,ac200 = <&ac200>;
+		x-powers,xmii-rx-clock-inverted;
+
+		ac200_ephy: ethernet-phy@1 {
+			compatible = "ethernet-phy-id0044.1400";
+			reg = <1>;
+		};
+	};
+};

[Severity: High]
Does building sun50i-h6-taiqicat-a01.dtb fail with unresolved phandle and label references here?

arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi in this tree does not yet define ac200_clk, rmii_pins, i2c3, ephy_calibration, or ac200, so dtbs builds with CONFIG_ARCH_SUNXI enabled fail in dtc unless the prerequisite sun50i-h6.dtsi changes are present.

Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=1
maintainer Acked-by on v1 1/1
#2 lore raw
In reply to Jun Yan

Dne torek, 17. november 2026 ob 15:21:21 Srednjeevropski standardni čas je Jun Yan napisal(a):

Quoted 9 lines

The TaiqiCat A01 has a 100 Mbit/s Ethernet port, which uses the EPHY integrated into the co-packaged AC200 of the Allwinner H6 SoC.

The AC200 derives its 24 MHz reference clock from PWM1, so enable the PWM controller and the pwm-clock node that supplies it. Also enable I2C3, over which the AC200 is accessed, and describe the AC200 EPHY package on the EMAC MDIO bus, with the EMAC operating in RMII mode.

Best regards,
Jernej

Quoted 88 lines

---
The AC200 MFD and EPHY drivers/bindings and the sun50i-h6.dtsi AC200 description this depends on are already merged in sunxi/dt-for-7.5.

---
 .../dts/allwinner/sun50i-h6-taiqicat-a01.dts  | 40 +++++++++++++++++++
 1 file changed, 40 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6-taiqicat-a01.dts +40 -0
index 225f42bd3b9e..9b192caeecb2 100644
@@ -14,6 +14,7 @@ / {
 	compatible = "ultrapower,taiqicat-a01", "allwinner,sun50i-h6";
 
 	aliases {
+		ethernet0 = &emac;
 		ethernet1 = &sdio_wifi;
 		serial0 = &uart0;
 	};
@@ -87,6 +88,10 @@ wifi_pwrseq: wifi-pwrseq {
 	};
 };
 
+&ac200_clk {
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_dcdca>;
 };
@@ -107,6 +112,14 @@ &ehci3 {
 	status = "okay";
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rmii_pins>;
+	phy-mode = "rmii";
+	phy-handle = <&ac200_ephy>;
+	status = "okay";
+};
+
 &gpu {
 	mali-supply = <&reg_dcdcc>;
 	status = "okay";
@@ -123,6 +136,29 @@ hdmi_out_con: endpoint {
 	};
 };
 
+&i2c3 {
+	status = "okay";
+};
+
+&mdio {
+	ethernet-phy-package@1 {
+		compatible = "x-powers,ac200-ephy-package";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		vcc-supply = <&reg_aldo2>;
+		nvmem-cells = <&ephy_calibration>;
+		nvmem-cell-names = "configuration";
+		x-powers,ac200 = <&ac200>;
+		x-powers,xmii-rx-clock-inverted;
+
+		ac200_ephy: ethernet-phy@1 {
+			compatible = "ethernet-phy-id0044.1400";
+			reg = <1>;
+		};
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_cldo1>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
@@ -173,6 +209,10 @@ &pio {
 	vcc-pg-supply = <&reg_bldo3>;
 };
 
+&pwm {
+	status = "okay";
+};
+
 &r_i2c {
 	status = "okay";