Skip to contentSkip to conversation

batman-adv: Split batadv proto in meshif and hardif part

RFC In review Sven Eckelmann 4 participants 6 messages Feb 24, 2019 – Mar 7, 2019

lore
Share & tools
lore
#0 lore raw

RFC 1/1 batman-adv: Split batadv proto in meshif and hardif part

batman-adv allows to configure three different objects:

* batadv hardif

- network interface used by batadv meshif to transport the batman-adv packets
- its master interface is set to the batadv meshif

* batadv (meshif/softif)

- virtual interface that emulates a normal 802.3 interface on top
- encapsulates traffic and forwards it via the batadv hardifs

* batadv vlan

- potential VLAN ID on top of batadv meshif
- allows filtering of traffic from specific VIDs

While batadv vlan objects were already represented as an own proto "batadv_vlan", the batadv meshif could never be fully configured using /etc/config/network. Instead, parts of its configuration were stored in /etc/config/batman_adv and some in the interfaces with the "batadv" proto.

To increase the confusion, the "batadv" proto wasn't used to define the batadv meshif but to identify batadv (slave) hardifs. The batman-adv meshifs were also never created directly but only when a hardif was configured. The actual modification of the configuration settings was then applied using a hotplug script hack. The batadv meshif network interface could therefore only be created when an hardif was available and not manipulated with ifup/ifdown. Also /etc/init.d/network reload didn't modify the batadv meshif interface configuration correctly.

The "batadv" is now renamed to "batadv_hardif" and a new "batadv" proto is used to configure the main (meshif) network interface with all its configuration.

A simple network configuration with WiFi & ethernet interfaces and static IP on top of bat0 would look like:

  # batadv meshif bat0
  config interface 'bat0'
  	option proto 'batadv'
  	option routing_algo 'BATMAN_IV'
  	option aggregated_ogms 1
  	option ap_isolation 0
  	option bonding 0
  	option fragmentation 1
  	#option gw_bandwidth '10000/2000'
  	option gw_mode 'off'
  	#option gw_sel_class 20
  	option log_level 0
  	option orig_interval 1000
  	option bridge_loop_avoidance 1
  	option distributed_arp_table 1
  	option multicast_mode 1
  	option network_coding 0
  	option hop_penalty 30
  	option isolation_mark '0x00000000/0x00000000'
  # add *single* wifi-iface with network bat0_hardif_wlan as hardif to bat0
  config interface 'bat0_hardif_wlan'
  	option mtu '1536'
  	option proto 'batadv_hardif'
  	option master 'bat0'
  	# option ifname is filled out by the wifi-iface
  # add eth0 as hardif to bat0
  config interface 'bat0_hardif_eth0'
  	option proto 'batadv_hardif'
  	option master 'bat0'
  	option ifname 'eth0'
  	option mtu '1536'
  # configure IP on bat0
  config interface 'bat0_lan'
  	option ifname 'bat0'
  	option proto 'static'
  	option ipaddr '192.168.1.1'
  	option netmask '255.255.255.0'
  	option ip6assign '60'

---
Cc: Matthias Schiffer <[email protected]>
Cc: [email protected]
Cc: Gui Iribarren <[email protected]>
Cc: Moritz Warning <[email protected]>

Changes depend on https://github.com/openwrt-routing/packages/pull/451

---
 batman-adv/Makefile                           |   2 +-
 batman-adv/files/etc/config/batman-adv        |  20 ----
 .../files/etc/hotplug.d/net/99-batman-adv     |  12 --
 .../etc/uci-defaults/99-migrate-batadv_hardif |  97 +++++++++++++++
 batman-adv/files/lib/batman-adv/config.sh     |  69 -----------
 batman-adv/files/lib/netifd/proto/batadv.sh   | 112 +++++++++++++++---
 .../files/lib/netifd/proto/batadv_hardif.sh   |  40 +++++++
 7 files changed, 235 insertions(+), 117 deletions(-)
 delete mode 100644 batman-adv/files/etc/config/batman-adv
 delete mode 100644 batman-adv/files/etc/hotplug.d/net/99-batman-adv
 create mode 100755 batman-adv/files/etc/uci-defaults/99-migrate-batadv_hardif
 delete mode 100644 batman-adv/files/lib/batman-adv/config.sh
 create mode 100755 batman-adv/files/lib/netifd/proto/batadv_hardif.sh
batman-adv/Makefile +1 -1
index 82af6c7..b250888 100644
@@ -10,7 +10,7 @@ include $(TOPDIR)/rules.mk
 PKG_NAME:=batman-adv
 
 PKG_VERSION:=2019.0
-PKG_RELEASE:=2
+PKG_RELEASE:=3
 PKG_HASH:=3e97d8a771cdbd7b2df42c52b88e071eaa58b5d28eb4e17a4b13b6698debbdc0
 
 PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION).tar.gz
batman-adv/files/etc/config/batman-adv deleted +0 -20
deleted file mode 100644
index 21138cb..0000000
@@ -1,20 +0,0 @@
-
-config 'mesh' 'bat0'
-	#option 'aggregated_ogms' 1
-	#option 'ap_isolation' 0
-	#option 'bonding' 0
-	#option 'fragmentation' 1
-	#option 'gw_bandwidth' '10000/2000'
-	#option 'gw_mode' 'off'
-	#option 'gw_sel_class' 20
-	#option 'log_level' 0
-	#option 'orig_interval' 1000
-	#option 'bridge_loop_avoidance' 1
-	#option 'distributed_arp_table' 1
-	#option 'multicast_mode' 1
-	#option 'network_coding' 0
-	#option 'hop_penalty' 30
-	#option 'isolation_mark' '0x00000000/0x00000000'
-
-# yet another batX instance
-# config 'mesh' 'bat5'
batman-adv/files/etc/hotplug.d/net/99-batman-adv deleted +0 -12
deleted file mode 100644
index f0c391f..0000000
@@ -1,12 +0,0 @@
-#!/bin/sh
-
-. /lib/batman-adv/config.sh
-
-bat_load_module
-config_load batman-adv
-
-case "$ACTION" in
-	add)
-		[ -d /sys/class/net/$INTERFACE/mesh/ ] && bat_config "$INTERFACE"
-		;;
-esac
batman-adv/files/etc/uci-defaults/99-migrate-batadv_hardif new file +97 -0

97 lines not on this page · raw message

batman-adv/files/lib/batman-adv/config.sh deleted +0 -69

69 lines not on this page · raw message

batman-adv/files/lib/netifd/proto/batadv.sh +97 -15

134 lines not on this page · raw message

batman-adv/files/lib/netifd/proto/batadv_hardif.sh new file +40 -0
new file mode 100755
index 0000000..9283d2b
@@ -0,0 +1,40 @@
+#!/bin/sh
+
+[ -n "$INCLUDE_ONLY" ] || {
+	. /lib/functions.sh
+	. ../netifd-proto.sh
+	init_proto "$@"
+}
+
+proto_batadv_hardif_init_config() {
+	proto_config_add_string "master"
+}
+
+proto_batadv_hardif_setup() {
+	local config="$1"
+	local iface="$2"
+
+	local master
+
+	json_get_vars master
+
+	( proto_add_host_dependency "$config" '' "$master" )
+
+	batctl -m "$master" interface -M add "$iface"
+
+	proto_init_update "$iface" 1
+	proto_send_update "$config"
+}
+
+proto_batadv_hardif_teardown() {
+	local config="$1"
+	local iface="$2"
+
+	local master
+
+	json_get_vars master
+
+	batctl -m "$master" interface -M del "$iface" || true
+}
+
+add_protocol batadv_hardif
Signature · 1 line
2.20.1
#1 lore raw

agree on the current mess, and congratulations on working on it :)
have you considered, to simplify backwards compatibility, to keep proto "batadv" as it currently is (hardif) and naming "batadv_mesh" the new proto?

Am 24. Februar 2019 13:51:13 GMT-03:00 schrieb Sven Eckelmann <[email protected]>:

Quoted 580 lines

batman-adv allows to configure three different objects:

* batadv hardif

- network interface used by batadv meshif to transport the batman-adv packets
- its master interface is set to the batadv meshif

* batadv (meshif/softif)

- virtual interface that emulates a normal 802.3 interface on top
- encapsulates traffic and forwards it via the batadv hardifs

* batadv vlan

- potential VLAN ID on top of batadv meshif
- allows filtering of traffic from specific VIDs

While batadv vlan objects were already represented as an own proto "batadv_vlan", the batadv meshif could never be fully configured using /etc/config/network. Instead, parts of its configuration were stored in /etc/config/batman_adv and some in the interfaces with the "batadv" proto.

To increase the confusion, the "batadv" proto wasn't used to define the batadv meshif but to identify batadv (slave) hardifs. The batman-adv meshifs were also never created directly but only when a hardif was configured. The actual modification of the configuration settings was then
applied using a hotplug script hack. The batadv meshif network interface
could therefore only be created when an hardif was available and not manipulated with ifup/ifdown. Also /etc/init.d/network reload didn't modify the batadv meshif interface configuration correctly.

The "batadv" is now renamed to "batadv_hardif" and a new "batadv" proto is
used to configure the main (meshif) network interface with all its configuration.

A simple network configuration with WiFi & ethernet interfaces and static
IP on top of bat0 would look like:

 # batadv meshif bat0
 config interface 'bat0'
(quoted diff) +0 -0
 	option proto 'batadv'
 	option routing_algo 'BATMAN_IV'
 	option aggregated_ogms 1
 	option ap_isolation 0
 	option bonding 0
 	option fragmentation 1
 	#option gw_bandwidth '10000/2000'
 	option gw_mode 'off'
 	#option gw_sel_class 20
 	option log_level 0
 	option orig_interval 1000
 	option bridge_loop_avoidance 1
 	option distributed_arp_table 1
 	option multicast_mode 1
 	option network_coding 0
 	option hop_penalty 30
 	option isolation_mark '0x00000000/0x00000000'
# add *single* wifi-iface with network bat0_hardif_wlan as hardif to
bat0
 config interface 'bat0_hardif_wlan'
(quoted diff) +0 -0
 	option mtu '1536'
 	option proto 'batadv_hardif'
 	option master 'bat0'
 	# option ifname is filled out by the wifi-iface
 
 # add eth0 as hardif to bat0
 config interface 'bat0_hardif_eth0'
 	option proto 'batadv_hardif'
 	option master 'bat0'
 	option ifname 'eth0'
 	option mtu '1536'
 
 # configure IP on bat0
 config interface 'bat0_lan'
 	option ifname 'bat0'
 	option proto 'static'
 	option ipaddr '192.168.1.1'
 	option netmask '255.255.255.0'
 	option ip6assign '60'

---
Cc: Matthias Schiffer <[email protected]>
Cc: [email protected]
Cc: Gui Iribarren <[email protected]>
Cc: Moritz Warning <[email protected]>

Changes depend on https://github.com/openwrt-routing/packages/pull/451
---

batman-adv/Makefile                           |   2 +-
batman-adv/files/etc/config/batman-adv        |  20 ----
.../files/etc/hotplug.d/net/99-batman-adv     |  12 --
.../etc/uci-defaults/99-migrate-batadv_hardif |  97 +++++++++++++++
batman-adv/files/lib/batman-adv/config.sh     |  69 -----------
batman-adv/files/lib/netifd/proto/batadv.sh   | 112 +++++++++++++++---
.../files/lib/netifd/proto/batadv_hardif.sh   |  40 +++++++
7 files changed, 235 insertions(+), 117 deletions(-)

delete mode 100644 batman-adv/files/etc/config/batman-adv delete mode 100644 batman-adv/files/etc/hotplug.d/net/99-batman-adv create mode 100755 batman-adv/files/etc/uci-defaults/99-migrate-batadv_hardif delete mode 100644 batman-adv/files/lib/batman-adv/config.sh create mode 100755 batman-adv/files/lib/netifd/proto/batadv_hardif.sh

batman-adv/Makefile +0 -0
index 82af6c7..b250888 100644
@@ -10,7 +10,7 @@ include $(TOPDIR)/rules.mk

PKG_NAME:=batman-adv

PKG_VERSION:=2019.0

batman-adv/Makefile +1 -1
-PKG_RELEASE:=2
+PKG_RELEASE:=3

PKG_HASH:=3e97d8a771cdbd7b2df42c52b88e071eaa58b5d28eb4e17a4b13b6698debbdc0

PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION).tar.gz

batman-adv/files/etc/config/batman-adv deleted +0 -20
deleted file mode 100644
index 21138cb..0000000
@@ -1,20 +0,0 @@
-
-config 'mesh' 'bat0'
-	#option 'aggregated_ogms' 1
-	#option 'ap_isolation' 0
-	#option 'bonding' 0
-	#option 'fragmentation' 1
-	#option 'gw_bandwidth' '10000/2000'
-	#option 'gw_mode' 'off'
-	#option 'gw_sel_class' 20
-	#option 'log_level' 0
-	#option 'orig_interval' 1000
-	#option 'bridge_loop_avoidance' 1
-	#option 'distributed_arp_table' 1
-	#option 'multicast_mode' 1
-	#option 'network_coding' 0
-	#option 'hop_penalty' 30
-	#option 'isolation_mark' '0x00000000/0x00000000'
-
-# yet another batX instance
-# config 'mesh' 'bat5'
batman-adv/files/etc/hotplug.d/net/99-batman-adv deleted +0 -12
deleted file mode 100644
index f0c391f..0000000
@@ -1,12 +0,0 @@
-#!/bin/sh
-
-. /lib/batman-adv/config.sh
-
-bat_load_module
-config_load batman-adv
-
-case "$ACTION" in
-	add)
-		[ -d /sys/class/net/$INTERFACE/mesh/ ] && bat_config "$INTERFACE"
-		;;
-esac
batman-adv/files/etc/uci-defaults/99-migrate-batadv_hardif new file +3 -0
new file mode 100755
index 0000000..156a33f
@@ -0,0 +1,97 @@
+#!/bin/sh
+
+# This UCI-Defaults script will split the batadv proto network

interfaces

batman-adv/files/etc/uci-defaults/99-migrate-batadv_hardif new file +27 -0
+# in batadv_hardif and batadv proto. The configuration options from
+# /etc/config/batman-adv will be moved to the latter.
+
+. /lib/functions.sh
+
+proto_batadv_to_batadv_hardif() {
+    local section="$1"
+    local proto
+    local mesh
+    local routing_algo
+
+    config_get proto "${section}" proto
+    config_get mesh "${section}" mesh
+    config_get routing_algo "${section}" routing_algo
+
+    if [ -z "$mesh" -o "${proto}" != "batadv" ]; then
+        continue
+    fi
+
+    uci set network."${section}".proto="batadv_hardif"
+    uci rename network."${section}".mesh="master"
+    uci delete network."${section}".routing_algo
+
+    # create new section or adjust existing one
+    uci set network."${mesh}"=interface
+    uci set network."${mesh}".proto=batadv
+    [ -n "${routing_algo}" ]  && uci set

network."${mesh}".routing_algo="${routing_algo}"

batman-adv/files/etc/uci-defaults/99-migrate-batadv_hardif new file +24 -0
+}
+
+mv_batadv_config_section() {
+    local section="$1"
+    local aggregated_ogms
+    local ap_isolation
+    local bonding
+    local bridge_loop_avoidance
+    local distributed_arp_table
+    local fragmentation
+    local gw_bandwidth
+    local gw_mode
+    local gw_sel_class
+    local hop_penalty
+    local isolation_mark
+    local log_level
+    local multicast_mode
+    local network_coding
+    local orig_interval
+
+    config_get aggregated_ogms "${section}" aggregated_ogms
+    config_get ap_isolation "${section}" ap_isolation
+    config_get bonding "${section}" bonding
+    config_get bridge_loop_avoidance "${section}"

bridge_loop_avoidance
+ config_get distributed_arp_table "${section}"
distributed_arp_table

batman-adv/files/etc/uci-defaults/99-migrate-batadv_hardif new file +13 -0
+    config_get fragmentation "${section}" fragmentation
+    config_get gw_bandwidth "${section}" gw_bandwidth
+    config_get gw_mode "${section}" gw_mode
+    config_get gw_sel_class "${section}" gw_sel_class
+    config_get hop_penalty "${section}" hop_penalty
+    config_get isolation_mark "${section}" isolation_mark
+    config_get log_level "${section}" log_level
+    config_get multicast_mode "${section}" multicast_mode
+    config_get network_coding "${section}" network_coding
+    config_get orig_interval "${section}" orig_interval
+
+    # update section in case it exists
+    [ -n "${aggregated_ogms}" ]  && uci set

network."${section}".aggregated_ogms="${aggregated_ogms}"
+ [ -n "${ap_isolation}" ] && uci set
network."${section}".ap_isolation="${ap_isolation}"
+ [ -n "${bonding}" ] && uci set
network."${section}".bonding="${bonding}"
+ [ -n "${bridge_loop_avoidance}" ] && uci set
network."${section}".bridge_loop_avoidance="${bridge_loop_avoidance}"
+ [ -n "${distributed_arp_table}" ] && uci set
network."${section}".distributed_arp_table="${distributed_arp_table}"
+ [ -n "${fragmentation}" ] && uci set
network."${section}".fragmentation="${fragmentation}"
+ [ -n "${gw_bandwidth}" ] && uci set
network."${section}".gw_bandwidth="${gw_bandwidth}"
+ [ -n "${gw_mode}" ] && uci set
network."${section}".gw_mode="${gw_mode}"
+ [ -n "${gw_sel_class}" ] && uci set
network."${section}".gw_sel_class="${gw_sel_class}"
+ [ -n "${hop_penalty}" ] && uci set
network."${section}".hop_penalty="${hop_penalty}"
+ [ -n "${isolation_mark}" ] && uci set
network."${section}".isolation_mark="${isolation_mark}"
+ [ -n "${log_level}" ] && uci set
network."${section}".log_level="${log_level}"
+ [ -n "${multicast_mode}" ] && uci set
network."${section}".multicast_mode="${multicast_mode}"
+ [ -n "${network_coding}" ] && uci set
network."${section}".network_coding="${network_coding}"
+ [ -n "${orig_interval}" ] && uci set
network."${section}".orig_interval="${orig_interval}"

batman-adv/files/etc/uci-defaults/99-migrate-batadv_hardif new file +15 -0
+}
+
+if [ -f /etc/config/batman-adv ]; then
+    config_load network
+    config_foreach proto_batadv_to_batadv_hardif 'interface'
+    uci commit network
+
+    config_load batman-adv
+    config_foreach mv_batadv_config_section 'mesh'
+    uci commit batman-adv
+
+    rm -f /etc/config/batman-adv
+fi
+
+exit 0
batman-adv/files/lib/batman-adv/config.sh deleted +0 -8
deleted file mode 100644
index 952f93e..0000000
@@ -1,69 +0,0 @@
-#!/bin/sh
-
-bat_load_module()
-{
-	[ -d "/sys/module/batman_adv/" ] && return
-
-	. /lib/functions.sh
-	load_modules /etc/modules.d/*-crc16 /etc/modules.d/*-crypto*

/etc/modules.d/*-lib-crc* /etc/modules.d/*-batman-adv*

batman-adv/files/lib/batman-adv/config.sh deleted +0 -6
-}
-
-bat_config()
-{
-	local mesh="$1"
-	local aggregated_ogms ap_isolation bonding bridge_loop_avoidance

distributed_arp_table fragmentation

batman-adv/files/lib/batman-adv/config.sh deleted +0 -1
-	local gw_bandwidth gw_mode gw_sel_class isolation_mark hop_penalty

multicast_mode network_coding log_level

batman-adv/files/lib/batman-adv/config.sh deleted +0 -19
-	local orig_interval
-
-	config_get aggregated_ogms "$mesh" aggregated_ogms
-	config_get ap_isolation "$mesh" ap_isolation
-	config_get bonding "$mesh" bonding
-	config_get bridge_loop_avoidance "$mesh" bridge_loop_avoidance
-	config_get distributed_arp_table "$mesh" distributed_arp_table
-	config_get fragmentation "$mesh" fragmentation
-	config_get gw_bandwidth "$mesh" gw_bandwidth
-	config_get gw_mode "$mesh" gw_mode
-	config_get gw_sel_class "$mesh" gw_sel_class
-	config_get hop_penalty "$mesh" hop_penalty
-	config_get isolation_mark "$mesh" isolation_mark
-	config_get multicast_mode "$mesh" multicast_mode
-	config_get network_coding "$mesh" network_coding
-	config_get log_level "$mesh" log_level
-	config_get orig_interval "$mesh" orig_interval
-
-	[ ! -f "/sys/class/net/$mesh/mesh/orig_interval" ] && echo

"batman-adv mesh $mesh does not exist - check your interface configuration" && return 1

batman-adv/files/lib/batman-adv/config.sh deleted +0 -2
-
-	[ -n "$aggregated_ogms" ] && batctl -m "$mesh" aggregation

"$aggregated_ogms"

batman-adv/files/lib/batman-adv/config.sh deleted +0 -1
-	[ -n "$ap_isolation" ] && batctl -m "$mesh" ap_isolation

"$ap_isolation"

batman-adv/files/lib/batman-adv/config.sh deleted +0 -2
-	[ -n "$bonding" ] && batctl -m "$mesh" bonding "$bonding"
-	[ -n "$bridge_loop_avoidance" ] &&  batctl -m "$mesh"

bridge_loop_avoidance "$bridge_loop_avoidance" 2>&-

batman-adv/files/lib/batman-adv/config.sh deleted +0 -1
-	[ -n "$distributed_arp_table" ] && batctl -m "$mesh"

distributed_arp_table "$distributed_arp_table" 2>&-

batman-adv/files/lib/batman-adv/config.sh deleted +0 -1
-	[ -n "$fragmentation" ] && batctl -m "$mesh" fragmentation

"$fragmentation"

batman-adv/files/lib/batman-adv/config.sh deleted +0 -23
-
-	case "$gw_mode" in
-	server)
-		if [ -n "$gw_bandwidth" ]; then
-			batctl -m "$mesh" gw_mode "server" "$gw_bandwidth"
-		else
-			batctl -m "$mesh" gw_mode "server"
-		fi
-		;;
-	client)
-		if [ -n "$gw_sel_class" ]; then
-			batctl -m "$mesh" gw_mode "client" "$gw_sel_class"
-		else
-			batctl -m "$mesh" gw_mode "client"
-		fi
-		;;
-	*)
-		batctl -m "$mesh" gw_mode "off"
-		;;
-	esac
-
-	[ -n "$hop_penalty" ] && batctl -m "$mesh" hop_penalty "$hop_penalty"
-	[ -n "$isolation_mark" ] && batctl -m "$mesh" isolation_mark

"$isolation_mark"

batman-adv/files/lib/batman-adv/config.sh deleted +0 -1
-	[ -n "$multicast_mode" ] && batctl -m "$mesh" multicast_mode

"$multicast_mode" 2>&-

batman-adv/files/lib/batman-adv/config.sh deleted +0 -1
-	[ -n "$network_coding" ] && batctl -m "$mesh" network_coding

"$network_coding" 2>&-

batman-adv/files/lib/batman-adv/config.sh deleted +0 -2
-	[ -n "$log_level" ] && batctl -m "$mesh" loglevel "$log_level" 2>&-
-	[ -n "$orig_interval" ] && batctl -m "$mesh" orig_interval

"$orig_interval"

batman-adv/files/lib/batman-adv/config.sh deleted +0 -1
-}
batman-adv/files/lib/netifd/proto/batadv.sh +63 -9
index 2233091..eb8153c 100755
@@ -1,37 +1,119 @@
 #!/bin/sh
 
-. /lib/functions.sh
-. ../netifd-proto.sh
-init_proto "$@"
+[ -n "$INCLUDE_ONLY" ] || {
+	. /lib/functions.sh
+	. ../netifd-proto.sh
+	init_proto "$@"
+}
 
 proto_batadv_init_config() {
-	proto_config_add_string "mesh"
-	proto_config_add_string "routing_algo"
+	no_device=1
+	available=1
+
+	proto_config_add_boolean 'aggregated_ogms:bool'
+	proto_config_add_boolean 'ap_isolation:bool'
+	proto_config_add_boolean 'bonding:bool'
+	proto_config_add_boolean 'bridge_loop_avoidance:bool'
+	proto_config_add_boolean 'distributed_arp_table:bool'
+	proto_config_add_boolean 'fragmentation:bool'
+	proto_config_add_string 'gw_bandwidth'
+	proto_config_add_string 'gw_mode'
+	proto_config_add_int 'gw_sel_class'
+	proto_config_add_int 'hop_penalty'
+	proto_config_add_string 'isolation_mark'
+	proto_config_add_string 'log_level'
+	proto_config_add_boolean 'multicast_mode:bool'
+	proto_config_add_boolean 'network_coding:bool'
+	proto_config_add_int 'orig_interval'
+	proto_config_add_string 'routing_algo'
 }
 
 proto_batadv_setup() {
 	local config="$1"
-	local iface="$2"
+	local iface="$config"
+
+	local aggregated_ogms
+	local ap_isolation
+	local bonding
+	local bridge_loop_avoidance
+	local distributed_arp_table
+	local fragmentation
+	local gw_bandwidth
+	local gw_mode
+	local gw_sel_class
+	local hop_penalty
+	local isolation_mark
+	local log_level
+	local multicast_mode
+	local network_coding
+	local orig_interval
+	local routing_algo
+
+	json_get_vars aggregated_ogms
+	json_get_vars ap_isolation
+	json_get_vars bonding
+	json_get_vars bridge_loop_avoidance
+	json_get_vars distributed_arp_table
+	json_get_vars fragmentation
+	json_get_vars gw_bandwidth
+	json_get_vars gw_mode
+	json_get_vars gw_sel_class
+	json_get_vars hop_penalty
+	json_get_vars isolation_mark
+	json_get_vars log_level
+	json_get_vars multicast_mode
+	json_get_vars network_coding
+	json_get_vars orig_interval
+	json_get_vars routing_algo
 
-	local mesh routing_algo
-	json_get_vars mesh routing_algo
+	set_default routing_algo 'BATMAN_IV'
 
-	[ -n "$routing_algo" ] || routing_algo="BATMAN_IV"
 	batctl routing_algo "$routing_algo"
+	batctl -m "$iface" interface create
+
+	[ -n "$aggregated_ogms" ] && batctl -m "$iface" aggregation

"$aggregated_ogms"

batman-adv/files/lib/netifd/proto/batadv.sh +1 -0
+	[ -n "$ap_isolation" ] && batctl -m "$iface" ap_isolation

"$ap_isolation"

batman-adv/files/lib/netifd/proto/batadv.sh +2 -0
+	[ -n "$bonding" ] && batctl -m "$iface" bonding "$bonding"
+	[ -n "$bridge_loop_avoidance" ] &&  batctl -m "$iface"

bridge_loop_avoidance "$bridge_loop_avoidance" 2>&-

batman-adv/files/lib/netifd/proto/batadv.sh +1 -0
+	[ -n "$distributed_arp_table" ] && batctl -m "$iface"

distributed_arp_table "$distributed_arp_table" 2>&-

batman-adv/files/lib/netifd/proto/batadv.sh +1 -0
+	[ -n "$fragmentation" ] && batctl -m "$iface" fragmentation

"$fragmentation"

batman-adv/files/lib/netifd/proto/batadv.sh +22 -0
+
+	case "$gw_mode" in
+	server)
+		if [ -n "$gw_bandwidth" ]; then
+			batctl -m "$iface" gw_mode "server" "$gw_bandwidth"
+		else
+			batctl -m "$iface" gw_mode "server"
+		fi
+		;;
+	client)
+		if [ -n "$gw_sel_class" ]; then
+			batctl -m "$iface" gw_mode "client" "$gw_sel_class"
+		else
+			batctl -m "$iface" gw_mode "client"
+		fi
+		;;
+	*)
+		batctl -m "$iface" gw_mode "off"
+		;;
+	esac
+
+	[ -n "$hop_penalty" ] && batctl -m "$iface" hop_penalty

"$hop_penalty"

batman-adv/files/lib/netifd/proto/batadv.sh +1 -0
+	[ -n "$isolation_mark" ] && batctl -m "$iface" isolation_mark

"$isolation_mark"

batman-adv/files/lib/netifd/proto/batadv.sh +1 -0
+	[ -n "$multicast_mode" ] && batctl -m "$iface" multicast_mode

"$multicast_mode" 2>&-

batman-adv/files/lib/netifd/proto/batadv.sh +1 -0
+	[ -n "$network_coding" ] && batctl -m "$iface" network_coding

"$network_coding" 2>&-

batman-adv/files/lib/netifd/proto/batadv.sh +2 -0
+	[ -n "$log_level" ] && batctl -m "$iface" loglevel "$log_level" 2>&-
+	[ -n "$orig_interval" ] && batctl -m "$iface" orig_interval

"$orig_interval"

batman-adv/files/lib/netifd/proto/batadv.sh +0 -1
-	batctl -m "$mesh" interface add "$iface"

proto_init_update "$iface" 1
proto_send_update "$config"
}

proto_batadv_teardown() {
	local config="$1"
batman-adv/files/lib/netifd/proto/batadv.sh +2 -5
-	local iface="$2"
-
-	local mesh
-	json_get_vars mesh
+	local iface="$config"
 
-	batctl -m "$mesh" interface del "$iface" || true
+	batctl -m "$iface" interface destroy

}

add_protocol batadv

batman-adv/files/lib/netifd/proto/batadv_hardif.sh new file +40 -0
new file mode 100755
index 0000000..9283d2b
@@ -0,0 +1,40 @@
+#!/bin/sh
+
+[ -n "$INCLUDE_ONLY" ] || {
+	. /lib/functions.sh
+	. ../netifd-proto.sh
+	init_proto "$@"
+}
+
+proto_batadv_hardif_init_config() {
+	proto_config_add_string "master"
+}
+
+proto_batadv_hardif_setup() {
+	local config="$1"
+	local iface="$2"
+
+	local master
+
+	json_get_vars master
+
+	( proto_add_host_dependency "$config" '' "$master" )
+
+	batctl -m "$master" interface -M add "$iface"
+
+	proto_init_update "$iface" 1
+	proto_send_update "$config"
+}
+
+proto_batadv_hardif_teardown() {
+	local config="$1"
+	local iface="$2"
+
+	local master
+
+	json_get_vars master
+
+	batctl -m "$master" interface -M del "$iface" || true
+}
+
+add_protocol batadv_hardif
#2 lore raw
Quoted 2 lines · On Monday, 25 February 2019 02:24:56 CET Gui Iribarren wrote:

have you considered, to simplify backwards compatibility, to keep proto "batadv" as it currently is (hardif) and naming "batadv_mesh" the new proto?

It was one of the goals to *not* name the batadv hardif interface proto "batadv". And I wanted to have the batman-adv interface proto named "batadv" because this is the rtnl kind string. So you actually create batman-adv meshifs using:

ip link add dev bat0 type batadv

But we can call this proto also "batadv_meshif" if there is a strong preference for this name.

Kind regards,
Sven

#3 lore raw

Hello.

That looks pretty cool.
But what about ELP interval parameter?
As I think, it should be covered by UCI config too.

Best Regards,
Lukonin Kirill

пн, 25 февр. 2019 г. в 12:36, Sven Eckelmann <[email protected]>:

Quoted 17 lines · On Monday, 25 February 2019 02:24:56 CET Gui Iribarren wrote:
Quoted 2 lines

have you considered, to simplify backwards compatibility, to keep proto "batadv" as it currently is (hardif) and naming "batadv_mesh" the new proto?

It was one of the goals to *not* name the batadv hardif interface proto "batadv". And I wanted to have the batman-adv interface proto named "batadv" because this is the rtnl kind string. So you actually create batman-adv meshifs using:

ip link add dev bat0 type batadv

But we can call this proto also "batadv_meshif" if there is a strong preference for this name.

Kind regards,
Sven

#4 lore raw
Quoted 2 lines · On Monday, 25 February 2019 09:03:52 CET Кирилл Луконин wrote:

But what about ELP interval parameter?
As I think, it should be covered by UCI config too.

Please first provide a batctl patch to support this setting. Then we can discuss the uci integration.

Kind regards,
Sven

#5 lore raw
In reply to Sven Eckelmann
Quoted 73 lines · CET Sven Eckelmann

batman-adv allows to configure three different objects:

* batadv hardif

- network interface used by batadv meshif to transport the batman-adv packets
- its master interface is set to the batadv meshif

* batadv (meshif/softif)

- virtual interface that emulates a normal 802.3 interface on top
- encapsulates traffic and forwards it via the batadv hardifs

* batadv vlan

- potential VLAN ID on top of batadv meshif
- allows filtering of traffic from specific VIDs

While batadv vlan objects were already represented as an own proto "batadv_vlan", the batadv meshif could never be fully configured using /etc/config/network. Instead, parts of its configuration were stored in /etc/config/batman_adv and some in the interfaces with the "batadv" proto.

To increase the confusion, the "batadv" proto wasn't used to define the batadv meshif but to identify batadv (slave) hardifs. The batman-adv meshifs were also never created directly but only when a hardif was configured. The actual modification of the configuration settings was then applied using a hotplug script hack. The batadv meshif network interface could therefore only be created when an hardif was available and not manipulated with ifup/ifdown. Also /etc/init.d/network reload didn't modify the batadv meshif interface configuration correctly.

The "batadv" is now renamed to "batadv_hardif" and a new "batadv" proto is used to configure the main (meshif) network interface with all its configuration.

A simple network configuration with WiFi & ethernet interfaces and static IP on top of bat0 would look like:

  # batadv meshif bat0
  config interface 'bat0'
        option proto 'batadv'
        option routing_algo 'BATMAN_IV'
        option aggregated_ogms 1
        option ap_isolation 0
        option bonding 0
        option fragmentation 1
        #option gw_bandwidth '10000/2000'
        option gw_mode 'off'
        #option gw_sel_class 20
        option log_level 0
        option orig_interval 1000
        option bridge_loop_avoidance 1
        option distributed_arp_table 1
        option multicast_mode 1
        option network_coding 0
        option hop_penalty 30
        option isolation_mark '0x00000000/0x00000000'
  # add *single* wifi-iface with network bat0_hardif_wlan as hardif to bat0
  config interface 'bat0_hardif_wlan'
        option mtu '1536'
        option proto 'batadv_hardif'
        option master 'bat0'
        # option ifname is filled out by the wifi-iface
  # add eth0 as hardif to bat0
  config interface 'bat0_hardif_eth0'
        option proto 'batadv_hardif'
        option master 'bat0'
        option ifname 'eth0'
        option mtu '1536'
Quoted 7 lines
  # configure IP on bat0
  config interface 'bat0_lan'
        option ifname 'bat0'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'
        option ip6assign '60'

Hey,

thank you very much for proposing that. It looks very good to me. We just discussed personally if it were possible to get rid of the bat0_hardif sections, but we will need them to configure other things in the future (e.g. ELP intervals, throughput override). And doing the "ifname" list in bat0 would result in a bad hack as we currently have for bridges, this is not favorable.

So +1 from me for this.

Cheers,
Simon