question about devicetree entry pca954x
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hello,
Quoted 87 lines · On Thu, Jan 26, 2023 at 05:05:47PM +0000, [email protected] wrote:
Hello Mr. Pinchart,
you are listed as maintainer in the
i2c-mux-pca954x.yamlfile.May I ask if you could take a few minutes and have a look at the following problem, if you can spot a bug in the second DT snippet?
Because on the internet you can only find examples where devices are used behind the pca954x which do not use an interrupt.
Let me tell you about the problem.
At our old device we had implemented this, which worked perfect:
&i2c4 { pinctrl-names = "default","gpio"; pinctrl-0 = <&pinctrl_i2c4>; pinctrl-1 = <&pinctrl_i2c4_gpio>; sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; clock-frequency = <400000>; status = "okay"; touchscreen@26 { compatible = "ilitek,ili2117"; reg = <0x26>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ili2117_62>; interrupt-parent = <&gpio2>; interrupts = <7 IRQ_TYPE_EDGE_RISING>; reset-gpios = <&pca9554_interface 0 GPIO_ACTIVE_LOW>; }; proximity@39 { compatible = "avago,apds9960"; reg = <0x39>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_apds9960_39>; interrupt-parent = <&gpio2>; interrupts = <6 IRQ_TYPE_EDGE_RISING>; };.....
Then we want more proximity sensors in this device, that we decided to add the PCA9544A.
&i2c4 {
.....i2c4_mux_apds: i2c4-mux-pca9544@70 { compatible = "nxp,pca9544"; #address-cells = <1>; #size-cells = <0>; reg = <0x70>; interrupt-parent = <&gpio2>; interrupt-controller; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pca9544a_70>; interrupts = <6 IRQ_TYPE_EDGE_FALLING>; i2c@0 { #address-cells = <1>; #size-cells = <0>; reg = <0>; proximity@39 { compatible = "avago,apds9960"; reg = <0x39>; interrupts = <0 IRQ_TYPE_EDGE_FALLING>; interrupt-parent = <&i2c4_mux_apds>; }; };Both drivers (pca954x and apds9960) request threaded irqs in their probe function, but it does not work together. Although the apds9960 also gets one assigned, when the
handle_nested_irqfunction is called (After everything has been initialized. However, this seems to be the second call to this function! First call seems to be inside the initialization phase.) the irq seems to be disabled. And thus the processing does not start.
Quoted 2 lines
I think that the problem is in my devicetree entry, that the soc doesn't really know how to handle the interrupt of the apds9960.
How are interrupts connected at the hardware level ? Is the APDS9960 interrupt connected to the INT0 pin of the PCA9544 ?
You have switched from IRQ_TYPE_EDGE_RISING to IRQ_TYPE_EDGE_FALLING for the APDS9960, is that intentional ?
Is there any message printed to the kernel log around the time where either driver is probed, or when the APDS9960 interrupt is supposed to occur, that may indicate a problem ?
Signature · 3 lines
Regards, Laurent Pinchart
AW: #Extern_Re: question about devicetree entry pca954x
Von: Laurent Pinchart <[email protected]>
Gesendet: Donnerstag, 26. Januar 2023 19:06
An: Rademacher Ralf
Cc: [email protected]
Betreff: #Extern_Re: question about devicetree entry pca954x
Warnung: Achtung - Diese E-Mail stammt von einer externen Quelle. Seien Sie vorsichtig mit Links und Anhängen.
Warning: Attention - This e-mail is from an external source. Be careful with links and attachments.
Hello,
Quoted 87 lines · On Thu, Jan 26, 2023 at 05:05:47PM +0000, [email protected] wrote:
Hello Mr. Pinchart,
you are listed as maintainer in the
i2c-mux-pca954x.yamlfile.May I ask if you could take a few minutes and have a look at the following problem, if you can spot a bug in the second DT snippet?
Because on the internet you can only find examples where devices are used behind the pca954x which do not use an interrupt.
Let me tell you about the problem.
At our old device we had implemented this, which worked perfect:
&i2c4 {
pinctrl-names = "default","gpio";
pinctrl-0 = <&pinctrl_i2c4>;
pinctrl-1 = <&pinctrl_i2c4_gpio>;
sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; clock-frequency = <400000>;
status = "okay";touchscreen@26 {
compatible = "ilitek,ili2117";
reg = <0x26>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ili2117_62>; interrupt-parent = <&gpio2>;
interrupts = <7IRQ_TYPE_EDGE_RISING>; reset-gpios = <&pca9554_interface0GPIO_ACTIVE_LOW>; };proximity@39 {
compatible = "avago,apds9960"; reg = <0x39>;
pinctrl-names = "default"; pinctrl-0 = <&pinctrl_apds9960_39>; interrupt-parent = <&gpio2>; interrupts = <6IRQ_TYPE_EDGE_RISING>; };
.....Then we want more proximity sensors in this device, that we decided to add the PCA9544A.
&i2c4 {
.....
i2c4_mux_apds: i2c4-mux-pca9544@70 {
compatible = "nxp,pca9544";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x70>;
interrupt-parent = <&gpio2>;
interrupt-controller;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pca9544a_70>;
interrupts = <6IRQ_TYPE_EDGE_FALLING>;i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;proximity@39 {
compatible = "avago,apds9960"; reg = <0x39>;
interrupts = <0IRQ_TYPE_EDGE_FALLING>; interrupt-parent = <&i2c4_mux_apds>; };
};Both drivers (pca954x and apds9960) request threaded irqs in their probe function, but it does not work together. Although the apds9960 also gets one assigned, when the
handle_nested_irqfunction is called (After everything has been initialized. However, this seems to be the second call to this function! First call seems to be inside the initialization phase.) the irq seems to be disabled. And thus the processing does not start.
Quoted 2 lines
I think that the problem is in my devicetree entry, that the soc doesn't really know how to handle the interrupt of the apds9960.
How are interrupts connected at the hardware level ? Is the APDS9960 interrupt connected to the INT0 pin of the PCA9544 ?
Yes, it is.
You have switched from IRQ_TYPE_EDGE_RISING to IRQ_TYPE_EDGE_FALLING for the APDS9960, is that intentional ?
Yes, I assumed this is correct, because APDS9960 datasheet tells me that: "Interrupt open drain (active low)". So i thought i have to detect the falling edge, not the rising edge. The same in the datasheet of PCA9544A, there are 4 active low interrupt inputs.
Is there any message printed to the kernel log around the time where either driver is probed, or when the APDS9960 interrupt is supposed to occur, that may indicate a problem ?
I have inserted some DBGMSGs into the functions handle_nested_irq and in the pca954x_probe. during pca954x driver probe, there is the following output:
[ 2.869856] [DBGMSG] handle_nested_irq :irq = 0xdf
[ 2.869858] [DBGMSG] handle_nested_irq :action = 0x7ba41100
[ 2.874477] [DBGMSG] handle_nested_irq :irqd_irq_disabled(&desc->irq_data): false
[ 2.874479] [DBGMSG] handle_nested_irq :(unlikely(!action || irqd_irq_disabled(&desc->irq_data))): false [ 2.874501] [DBGMSG] handle_nested_irq :action->irq:df | action->dev_id:0x7ba64810
when a apds sends the interrupt signal to the pca954x, this happens:
[ 9336.607055] [DBGMSG] pca954x_irq_handler :pca954x_irq_handler starts [ 9336.607908] [DBGMSG] pca954x_irq_handler :i2c_smbus_read::retval=14 [ 9336.613255] [DBGMSG] pca954x_irq_handler :i=0 | bit: 4 is set in register [ 9336.619539] [DBGMSG] pca954x_irq_handler :irq= 0x65 // child_irq =0xe7 [ 9336.619542] [DBGMSG] handle_nested_irq :irq = 0xe7 [ 9336.632516] [DBGMSG] handle_nested_irq :action = 0x0 [ 9336.632519] [DBGMSG] handle_nested_irq :irqd_irq_disabled(&desc->irq_data):true [ 9336.632521] [DBGMSG] handle_nested_irq :(unlikely(!action || irqd_irq_disabled(&desc->irq_data))):true [ 9336.632523] [DBGMSG] handle_nested_irq :goto out_unlock
Regards,
Ralf Rademacher
--
Regards,
Laurent Pinchart
AW: #Extern_Re: question about devicetree entry pca954x
Mr. Pinchart,
i have to correct myself:
the first call of handle_nested_interrupt happens already before pca954x_probe. i added some more DBGMSGs
[ 2.869856] [DBGMSG] handle_nested_irq :irq = 0xdf [ 2.869858] [DBGMSG] handle_nested_irq :action = 0x7ba41100 [ 2.874477] [DBGMSG] handle_nested_irq :irqd_irq_disabled(&desc->irq_data): false [ 2.874479] [DBGMSG] handle_nested_irq :(unlikely(!action || irqd_irq_disabled(&desc->irq_data))): false [ 2.874501] [DBGMSG] handle_nested_irq :action->irq:df | action->dev_id:0x7ba64810 [ 6.373737] [DBGMSG] pca954x_probe :enter fxn [ 6.973918] [DBGMSG] pca954x_probe :leave fxn
Regards,
Ralf
Von: Rademacher Ralf
Gesendet: Donnerstag, 26. Januar 2023 21:18
An: Laurent Pinchart
Cc: [email protected]
Betreff: AW: #Extern_Re: question about devicetree entry pca954x
Von: Laurent Pinchart <[email protected]>
Gesendet: Donnerstag, 26. Januar 2023 19:06
An: Rademacher Ralf
Cc: [email protected]
Betreff: #Extern_Re: question about devicetree entry pca954x
Warnung: Achtung - Diese E-Mail stammt von einer externen Quelle. Seien Sie vorsichtig mit Links und Anhängen.
Warning: Attention - This e-mail is from an external source. Be careful with links and attachments.
Hello,
Quoted 87 lines · On Thu, Jan 26, 2023 at 05:05:47PM +0000, [email protected] wrote:
Hello Mr. Pinchart,
you are listed as maintainer in the
i2c-mux-pca954x.yamlfile.May I ask if you could take a few minutes and have a look at the following problem, if you can spot a bug in the second DT snippet?
Because on the internet you can only find examples where devices are used behind the pca954x which do not use an interrupt.
Let me tell you about the problem.
At our old device we had implemented this, which worked perfect:
&i2c4 {
pinctrl-names = "default","gpio";
pinctrl-0 = <&pinctrl_i2c4>;
pinctrl-1 = <&pinctrl_i2c4_gpio>;
sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; clock-frequency = <400000>;
status = "okay";touchscreen@26 {
compatible = "ilitek,ili2117";
reg = <0x26>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ili2117_62>; interrupt-parent = <&gpio2>;
interrupts = <7IRQ_TYPE_EDGE_RISING>; reset-gpios = <&pca9554_interface0GPIO_ACTIVE_LOW>; };proximity@39 {
compatible = "avago,apds9960"; reg = <0x39>;
pinctrl-names = "default"; pinctrl-0 = <&pinctrl_apds9960_39>; interrupt-parent = <&gpio2>; interrupts = <6IRQ_TYPE_EDGE_RISING>; };
.....Then we want more proximity sensors in this device, that we decided to add the PCA9544A.
&i2c4 {
.....
i2c4_mux_apds: i2c4-mux-pca9544@70 {
compatible = "nxp,pca9544";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x70>;
interrupt-parent = <&gpio2>;
interrupt-controller;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pca9544a_70>;
interrupts = <6IRQ_TYPE_EDGE_FALLING>;i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;proximity@39 {
compatible = "avago,apds9960"; reg = <0x39>;
interrupts = <0IRQ_TYPE_EDGE_FALLING>; interrupt-parent = <&i2c4_mux_apds>; };
};Both drivers (pca954x and apds9960) request threaded irqs in their probe function, but it does not work together. Although the apds9960 also gets one assigned, when the
handle_nested_irqfunction is called (After everything has been initialized. However, this seems to be the second call to this function! First call seems to be inside the initialization phase.) the irq seems to be disabled. And thus the processing does not start.
Quoted 2 lines
I think that the problem is in my devicetree entry, that the soc doesn't really know how to handle the interrupt of the apds9960.
How are interrupts connected at the hardware level ? Is the APDS9960 interrupt connected to the INT0 pin of the PCA9544 ?
Yes, it is.
You have switched from IRQ_TYPE_EDGE_RISING to IRQ_TYPE_EDGE_FALLING for the APDS9960, is that intentional ?
Yes, I assumed this is correct, because APDS9960 datasheet tells me that: "Interrupt open drain (active low)". So i thought i have to detect the falling edge, not the rising edge. The same in the datasheet of PCA9544A, there are 4 active low interrupt inputs.
Is there any message printed to the kernel log around the time where either driver is probed, or when the APDS9960 interrupt is supposed to occur, that may indicate a problem ?
I have inserted some DBGMSGs into the functions handle_nested_irq and in the pca954x_probe. during pca954x driver probe, there is the following output:
[ 2.869856] [DBGMSG] handle_nested_irq :irq = 0xdf
[ 2.869858] [DBGMSG] handle_nested_irq :action = 0x7ba41100
[ 2.874477] [DBGMSG] handle_nested_irq :irqd_irq_disabled(&desc->irq_data): false
[ 2.874479] [DBGMSG] handle_nested_irq :(unlikely(!action || irqd_irq_disabled(&desc->irq_data))): false [ 2.874501] [DBGMSG] handle_nested_irq :action->irq:df | action->dev_id:0x7ba64810
when a apds sends the interrupt signal to the pca954x, this happens:
[ 9336.607055] [DBGMSG] pca954x_irq_handler :pca954x_irq_handler starts [ 9336.607908] [DBGMSG] pca954x_irq_handler :i2c_smbus_read::retval=14 [ 9336.613255] [DBGMSG] pca954x_irq_handler :i=0 | bit: 4 is set in register [ 9336.619539] [DBGMSG] pca954x_irq_handler :irq= 0x65 // child_irq =0xe7 [ 9336.619542] [DBGMSG] handle_nested_irq :irq = 0xe7 [ 9336.632516] [DBGMSG] handle_nested_irq :action = 0x0 [ 9336.632519] [DBGMSG] handle_nested_irq :irqd_irq_disabled(&desc->irq_data):true [ 9336.632521] [DBGMSG] handle_nested_irq :(unlikely(!action || irqd_irq_disabled(&desc->irq_data))):true [ 9336.632523] [DBGMSG] handle_nested_irq :goto out_unlock
Regards,
Ralf Rademacher
--
Regards,
Laurent Pinchart
AW: #Extern_Re: question about devicetree entry pca954x
Hello Mr. Pinchart,
following on from our previous conversation, I have since observed the following.
The first call of handle_nested_interrupt() during startup was a result of another driver and had nothing to do with the problem. i used dump_stack() to find the callee.
For the problem, the current debug output reduces to the following:
[ 28.830817] [DBGMSG] pca954x_irq_handler :entering pca954x_irq_handler [ 28.831363] [DBGMSG] pca954x_irq_handler :i2c_smbus_read::retval=14 [ 28.837918] [DBGMSG] pca954x_irq_handler :i=0 | bit: 4 isset in register = true [ 28.837921] [DBGMSG] pca954x_irq_handler :irq= 0x65 // child_irq =0xe7 [ 28.851527] [DBGMSG] handle_nested_irq :entering handle_nested_irq [ 28.851542] Call trace: [ 28.851555] dump_backtrace+0x0/0x178 [ 28.851561] show_stack+0x24/0x30 [ 28.889839] dump_stack+0xb4/0x114 [ 28.893245] handle_nested_irq+0x44/0x23c [ 28.897258] pca954x_irq_handler+0xf4/0x138 [i2c_mux_pca954x] [ 28.903006] irq_thread_fn+0x30/0xa0 [ 28.906581] irq_thread+0x150/0x248 [ 28.910068] kthread+0x140/0x160 [ 28.913297] ret_from_fork+0x10/0x1c [ 28.916901] [DBGMSG] handle_nested_irq :irq: 0xe7 [ 28.916905] [DBGMSG] handle_nested_irq :irq_desc->name: (null) [ 28.921447] [DBGMSG] handle_nested_irq :irq_desc->parent_irq: 0x0
Do you have any idea what the problem could be?
I have no idea about, why the interrupt is disabled and why the action of the threaded interrupt is null Is it possible that I have forgotten something in the DeviceTree entry?
Best
Ralf
Von: Rademacher Ralf
Gesendet: Donnerstag, 26. Januar 2023 21:33
An: Laurent Pinchart
Cc: [email protected]
Betreff: AW: #Extern_Re: question about devicetree entry pca954x
Mr. Pinchart,
i have to correct myself:
the first call of handle_nested_interrupt happens already before pca954x_probe. i added some more DBGMSGs
[ 2.869856] [DBGMSG] handle_nested_irq :irq = 0xdf
[ 2.869858] [DBGMSG] handle_nested_irq :action = 0x7ba41100
[ 2.874477] [DBGMSG] handle_nested_irq :irqd_irq_disabled(&desc->irq_data): false
[ 2.874479] [DBGMSG] handle_nested_irq :(unlikely(!action || irqd_irq_disabled(&desc->irq_data))): false [ 2.874501] [DBGMSG] handle_nested_irq :action->irq:df | action->dev_id:0x7ba64810
[ 6.373737] [DBGMSG] pca954x_probe :enter fxn
[ 6.973918] [DBGMSG] pca954x_probe :leave fxn
Regards,
Ralf
Von: Rademacher Ralf
Gesendet: Donnerstag, 26. Januar 2023 21:18
An: Laurent Pinchart
Cc: [email protected]
Betreff: AW: #Extern_Re: question about devicetree entry pca954x
Von: Laurent Pinchart <[email protected]>
Gesendet: Donnerstag, 26. Januar 2023 19:06
An: Rademacher Ralf
Cc: [email protected]
Betreff: #Extern_Re: question about devicetree entry pca954x
Warnung: Achtung - Diese E-Mail stammt von einer externen Quelle. Seien Sie vorsichtig mit Links und Anhängen.
Warning: Attention - This e-mail is from an external source. Be careful with links and attachments.
Hello,
Quoted 87 lines · On Thu, Jan 26, 2023 at 05:05:47PM +0000, [email protected] wrote:
Hello Mr. Pinchart,
you are listed as maintainer in the
i2c-mux-pca954x.yamlfile.May I ask if you could take a few minutes and have a look at the following problem, if you can spot a bug in the second DT snippet?
Because on the internet you can only find examples where devices are used behind the pca954x which do not use an interrupt.
Let me tell you about the problem.
At our old device we had implemented this, which worked perfect:
&i2c4 {
pinctrl-names = "default","gpio";
pinctrl-0 = <&pinctrl_i2c4>;
pinctrl-1 = <&pinctrl_i2c4_gpio>;
sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; clock-frequency = <400000>;
status = "okay";touchscreen@26 {
compatible = "ilitek,ili2117";
reg = <0x26>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ili2117_62>; interrupt-parent = <&gpio2>;
interrupts = <7IRQ_TYPE_EDGE_RISING>; reset-gpios = <&pca9554_interface0GPIO_ACTIVE_LOW>; };proximity@39 {
compatible = "avago,apds9960"; reg = <0x39>;
pinctrl-names = "default"; pinctrl-0 = <&pinctrl_apds9960_39>; interrupt-parent = <&gpio2>; interrupts = <6IRQ_TYPE_EDGE_RISING>; };
.....Then we want more proximity sensors in this device, that we decided to add the PCA9544A.
&i2c4 {
.....
i2c4_mux_apds: i2c4-mux-pca9544@70 {
compatible = "nxp,pca9544";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x70>;
interrupt-parent = <&gpio2>;
interrupt-controller;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pca9544a_70>;
interrupts = <6IRQ_TYPE_EDGE_FALLING>;i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;proximity@39 {
compatible = "avago,apds9960"; reg = <0x39>;
interrupts = <0IRQ_TYPE_EDGE_FALLING>; interrupt-parent = <&i2c4_mux_apds>; };
};Both drivers (pca954x and apds9960) request threaded irqs in their probe function, but it does not work together. Although the apds9960 also gets one assigned, when the
handle_nested_irqfunction is called (After everything has been initialized. However, this seems to be the second call to this function! First call seems to be inside the initialization phase.) the irq seems to be disabled. And thus the processing does not start.
Quoted 2 lines
I think that the problem is in my devicetree entry, that the soc doesn't really know how to handle the interrupt of the apds9960.
How are interrupts connected at the hardware level ? Is the APDS9960 interrupt connected to the INT0 pin of the PCA9544 ?
Yes, it is.
You have switched from IRQ_TYPE_EDGE_RISING to IRQ_TYPE_EDGE_FALLING for the APDS9960, is that intentional ?
Yes, I assumed this is correct, because APDS9960 datasheet tells me that: "Interrupt open drain (active low)". So i thought i have to detect the falling edge, not the rising edge. The same in the datasheet of PCA9544A, there are 4 active low interrupt inputs.
Is there any message printed to the kernel log around the time where either driver is probed, or when the APDS9960 interrupt is supposed to occur, that may indicate a problem ?
I have inserted some DBGMSGs into the functions handle_nested_irq and in the pca954x_probe. during pca954x driver probe, there is the following output:
[ 2.869856] [DBGMSG] handle_nested_irq :irq = 0xdf
[ 2.869858] [DBGMSG] handle_nested_irq :action = 0x7ba41100
[ 2.874477] [DBGMSG] handle_nested_irq :irqd_irq_disabled(&desc->irq_data): false
[ 2.874479] [DBGMSG] handle_nested_irq :(unlikely(!action || irqd_irq_disabled(&desc->irq_data))): false [ 2.874501] [DBGMSG] handle_nested_irq :action->irq:df | action->dev_id:0x7ba64810
when a apds sends the interrupt signal to the pca954x, this happens:
[ 9336.607055] [DBGMSG] pca954x_irq_handler :pca954x_irq_handler starts [ 9336.607908] [DBGMSG] pca954x_irq_handler :i2c_smbus_read::retval=14 [ 9336.613255] [DBGMSG] pca954x_irq_handler :i=0 | bit: 4 is set in register [ 9336.619539] [DBGMSG] pca954x_irq_handler :irq= 0x65 // child_irq =0xe7 [ 9336.619542] [DBGMSG] handle_nested_irq :irq = 0xe7 [ 9336.632516] [DBGMSG] handle_nested_irq :action = 0x0 [ 9336.632519] [DBGMSG] handle_nested_irq :irqd_irq_disabled(&desc->irq_data):true [ 9336.632521] [DBGMSG] handle_nested_irq :(unlikely(!action || irqd_irq_disabled(&desc->irq_data))):true [ 9336.632523] [DBGMSG] handle_nested_irq :goto out_unlock
Regards,
Ralf Rademacher
--
Regards,
Laurent Pinchart
Re: AW: #Extern_Re: question about devicetree entry pca954x
Hello,
I'm sorry for the late reply, I've been very busy lately.
Quoted 8 lines · On Wed, Feb 08, 2023 at 03:56:15PM +0000, [email protected] wrote:
Hello Mr. Pinchart,
following on from our previous conversation, I have since observed the following.
The first call of
handle_nested_interrupt()during startup was a result of another driver and had nothing to do with the problem. i useddump_stack()to find the callee.
OK, that makes sense.
Quoted 21 lines
For the problem, the current debug output reduces to the following:
[ 28.830817] [DBGMSG] pca954x_irq_handler :entering pca954x_irq_handler [ 28.831363] [DBGMSG] pca954x_irq_handler :i2c_smbus_read::retval=14 [ 28.837918] [DBGMSG] pca954x_irq_handler :i=0 | bit: 4 isset in register = true [ 28.837921] [DBGMSG] pca954x_irq_handler :irq= 0x65 // child_irq =0xe7 [ 28.851527] [DBGMSG] handle_nested_irq :entering handle_nested_irq [ 28.851542] Call trace: [ 28.851555] dump_backtrace+0x0/0x178 [ 28.851561] show_stack+0x24/0x30 [ 28.889839] dump_stack+0xb4/0x114 [ 28.893245] handle_nested_irq+0x44/0x23c [ 28.897258] pca954x_irq_handler+0xf4/0x138 [i2c_mux_pca954x] [ 28.903006] irq_thread_fn+0x30/0xa0 [ 28.906581] irq_thread+0x150/0x248 [ 28.910068] kthread+0x140/0x160 [ 28.913297] ret_from_fork+0x10/0x1c [ 28.916901] [DBGMSG] handle_nested_irq :irq: 0xe7 [ 28.916905] [DBGMSG] handle_nested_irq :irq_desc->name: (null) [ 28.921447] [DBGMSG] handle_nested_irq :irq_desc->parent_irq: 0x0
Quoted 3 lines
Do you have any idea what the problem could be?
I have no idea about, why the interrupt is disabled and why the action of the threaded interrupt is null Is it possible that I have forgotten something in the DeviceTree entry?
Nothing immediately strikes me as wrong in your device tree.
Could you share the output of cat /proc/interrupts ? If the IRQ numbers listed in the log above (0x65 and 0xe7) have changed, please also share the new log, I want to correlate those numbers to /proc/interrupt entries.
Quoted 144 lines · Rademacher Ralf
Quoted 143 lines
Mr. Pinchart,i have to correct myself:
the first call ofhandle_nested_interrupthappens already beforepca954x_probe. i added some more DBGMSGs[ 2.869856] [DBGMSG]
handle_nested_irq:irq =0xdf
[ 2.869858] [DBGMSG]handle_nested_irq:action =0x7ba41100
[ 2.874477] [DBGMSG]handle_nested_irq:irqd_irq_disabled(&desc->irq_data): false
[ 2.874479] [DBGMSG]handle_nested_irq:(unlikely(!action ||irqd_irq_disabled(&desc->irq_data))): false [ 2.874501] [DBGMSG]handle_nested_irq:action->irq:df | action->dev_id:0x7ba64810
[ 6.373737] [DBGMSG]pca954x_probe:enter fxn
[ 6.973918] [DBGMSG]pca954x_probe:leave fxnQuoted 127 lines · Rademacher Ralf
Quoted 85 lines · Laurent Pinchart
Quoted 84 lines · On Thu, Jan 26, 2023 at 05:05:47PM +0000, [email protected] wrote:
Hello Mr. Pinchart,
you are listed as maintainer in the
i2c-mux-pca954x.yamlfile.May I ask if you could take a few minutes and have a look at the following problem, if you can spot a bug in the second DT snippet?
Because on the internet you can only find examples where devices are used behind the pca954x which do not use an interrupt.
Let me tell you about the problem.
At our old device we had implemented this, which worked perfect:
&i2c4 {
pinctrl-names = "default","gpio";
pinctrl-0 = <&pinctrl_i2c4>;
pinctrl-1 = <&pinctrl_i2c4_gpio>;
sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; clock-frequency = <400000>;
status = "okay";touchscreen@26 {
compatible = "ilitek,ili2117";
reg = <0x26>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ili2117_62>; interrupt-parent = <&gpio2>;
interrupts = <7IRQ_TYPE_EDGE_RISING>; reset-gpios = <&pca9554_interface0GPIO_ACTIVE_LOW>; };proximity@39 {
compatible = "avago,apds9960"; reg = <0x39>;
pinctrl-names = "default"; pinctrl-0 = <&pinctrl_apds9960_39>; interrupt-parent = <&gpio2>; interrupts = <6IRQ_TYPE_EDGE_RISING>; };
.....Then we want more proximity sensors in this device, that we decided to add the PCA9544A.
&i2c4 {
.....
i2c4_mux_apds: i2c4-mux-pca9544@70 {
compatible = "nxp,pca9544";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x70>;
interrupt-parent = <&gpio2>;
interrupt-controller;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pca9544a_70>;
interrupts = <6IRQ_TYPE_EDGE_FALLING>;i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;proximity@39 {
compatible = "avago,apds9960"; reg = <0x39>;
interrupts = <0IRQ_TYPE_EDGE_FALLING>; interrupt-parent = <&i2c4_mux_apds>; };
};Both drivers (pca954x and apds9960) request threaded irqs in their probe function, but it does not work together. Although the apds9960 also gets one assigned, when the
handle_nested_irqfunction is called (After everything has been initialized. However, this seems to be the second call to this function! First call seems to be inside the initialization phase.) the irq seems to be disabled. And thus the processing does not start.Quoted 5 lines
Quoted 2 lines
I think that the problem is in my devicetree entry, that the soc doesn't really know how to handle the interrupt of the apds9960.
How are interrupts connected at the hardware level ? Is the APDS9960 interrupt connected to the INT0 pin of the PCA9544 ?
Yes, it is.
Quoted 2 lines
You have switched from
IRQ_TYPE_EDGE_RISINGtoIRQ_TYPE_EDGE_FALLINGfor the APDS9960, is that intentional ?Yes, I assumed this is correct, because APDS9960 datasheet tells me
that: "Interrupt open drain (active low)". So i thought i have to detect the falling edge, not the rising edge. The same in the datasheet of PCA9544A, there are 4 active low interrupt inputs.Quoted 3 lines
Is there any message printed to the kernel log around the time where either driver is probed, or when the APDS9960 interrupt is supposed to occur, that may indicate a problem ?
I have inserted some DBGMSGs into the functions
handle_nested_irqand in thepca954x_probe. during pca954x driver probe, there is the following output:[ 2.869856] [DBGMSG]
handle_nested_irq:irq =0xdf
[ 2.869858] [DBGMSG]handle_nested_irq:action =0x7ba41100
[ 2.874477] [DBGMSG]handle_nested_irq:irqd_irq_disabled(&desc->irq_data): false
[ 2.874479] [DBGMSG]handle_nested_irq:(unlikely(!action ||irqd_irq_disabled(&desc->irq_data))): false [ 2.874501] [DBGMSG]handle_nested_irq:action->irq:df | action->dev_id:0x7ba64810when a apds sends the interrupt signal to the pca954x, this happens:
[ 9336.607055] [DBGMSG] pca954x_irq_handler :pca954x_irq_handler starts [ 9336.607908] [DBGMSG] pca954x_irq_handler :i2c_smbus_read::retval=14 [ 9336.613255] [DBGMSG] pca954x_irq_handler :i=0 | bit: 4 is set in register [ 9336.619539] [DBGMSG] pca954x_irq_handler :irq= 0x65 // child_irq =0xe7 [ 9336.619542] [DBGMSG] handle_nested_irq :irq = 0xe7 [ 9336.632516] [DBGMSG] handle_nested_irq :action = 0x0 [ 9336.632519] [DBGMSG] handle_nested_irq :irqd_irq_disabled(&desc->irq_data):true [ 9336.632521] [DBGMSG] handle_nested_irq :(unlikely(!action || irqd_irq_disabled(&desc->irq_data))):true [ 9336.632523] [DBGMSG] handle_nested_irq :goto out_unlock
Signature · 3 lines
Regards, Laurent Pinchart
AW: #Extern_Re: AW: #Extern_Re: question about devicetree entry pca954x
Hello Mr. Pinchart,
i attached new generated kernellog lines, hoping these snippets contain the data you need.
I separated the lines a bit to make the DBGMSGs stand out from the other content. Only lines related to the two drivers or chip.c are included. Down below there is a snipped from /proc/interrupts.
[ 6.888610] bus: 'i2c': add driver pca954x [ 6.888676] bus: 'i2c': driver_probe_device: matched device 3-0070 with driver pca954x [ 6.888686] bus: 'i2c': really_probe: probing driver pca954x with device 3-0070 [ 6.888775] pca954x 3-0070: no init pinctrl state [ 6.888784] pca954x 3-0070: no sleep pinctrl state [ 6.888787] pca954x 3-0070: no idle pinctrl state
[ 6.888829] [DBGMSG] pca954x_probe :entering pca954x_probe
[ 6.888836] pca954x 3-0070: GPIO lookup for consumer reset [ 6.888839] pca954x 3-0070: using device tree for GPIO lookup [ 6.888853] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/soc@0/bus@30800000/ i2c@30a50000/i2c4-mux-pca9544@70[0]' [ 6.888861] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/soc@0/bus@30800000/i 2c@30a50000/i2c4-mux-pca9544@70[0]' [ 6.888866] pca954x 3-0070: using lookup tables for GPIO lookup [ 6.888870] pca954x 3-0070: No GPIO consumer reset found
[ 6.908207] device: 'i2c-4': device_add [ 6.908240] bus: 'i2c': add device i2c-4 [ 6.908278] PM: Adding info for i2c:i2c-4 [ 6.908291] device: 'i2c-4': device_add [ 6.908331] PM: Adding info for No Bus:i2c-4 [ 6.911389] device: '4-0039': device_add [ 6.945282] bus: 'i2c': add device 4-0039 [ 7.069423] PM: Adding info for i2c:4-0039 [ 7.121093] i2c i2c-3: Added multiplexed i2c bus 4 [ 7.121162] device: 'i2c-5': device_add [ 7.122267] bus: 'i2c': add device i2c-5 [ 7.122327] PM: Adding info for i2c:i2c-5 [ 7.122381] device: 'i2c-5': device_add [ 7.122501] PM: Adding info for No Bus:i2c-5 [ 7.123477] device: '5-0039': device_add [ 7.123543] bus: 'i2c': add device 5-0039 [ 7.123666] PM: Adding info for i2c:5-0039 [ 7.126408] i2c i2c-3: Added multiplexed i2c bus 5 [ 7.182032] device: 'i2c-6': device_add [ 7.187695] bus: 'i2c': add device i2c-6 [ 7.187766] device: 'i2c-6': device_add [ 7.189430] device: '6-0039': device_add [ 7.189473] bus: 'i2c': add device 6-0039 [ 7.189503] PM: Adding info for i2c:6-0039 [ 7.193883] i2c i2c-3: Added multiplexed i2c bus 6 [ 7.199087] device: 'i2c-7': device_add [ 7.199286] bus: 'i2c': add device i2c-7 [ 7.199307] PM: Adding info for i2c:i2c-7 [ 7.199328] device: 'i2c-7': device_add [ 7.199361] PM: Adding info for No Bus:i2c-7 [ 7.199586] i2c i2c-3: Added multiplexed i2c bus 7 [ 7.211760] pca954x 3-0070: registered 4 multiplexed busses for I2C mux pca9544
[ 7.222122] [DBGMSG] pca954x_probe :leaving pca954x_probe
[ 7.222138] driver: 'pca954x': driver_bound: bound to device '3-0070' [ 7.291190] bus: 'i2c': really_probe: bound device 3-0070 to driver pca954x [ 7.403877] bus: 'i2c': add driver apds9960 [ 7.417379] bus: 'i2c': driver_probe_device: matched device 4-0039 with driver apds9960 [ 7.422911] bus: 'i2c': really_probe: probing driver apds9960 with device 4-0039 [ 7.422941] apds9960 4-0039: no pinctrl handle
[ 7.422990] [DBGMSG] apds9960_probe :enter apds probe [ 7.743904] [DBGMSG] apds9960_probe :client->irq: 0x5F / interrupt_handler_fxn: 0x92D0B3C
[ 7.744063] device: 'iio:device0': device_add [ 7.752407] bus: 'iio': add device iio:device0 [ 7.752431] PM: Adding info for iio:iio:device0 [ 7.752573] driver: 'apds9960': driver_bound: bound to device '4-0039' [ 7.752580] devices_kset: Moving 4-0039 to end of list [ 7.752584] PM: Moving i2c:4-0039 to end of list [ 7.752588] devices_kset: Moving iio:device0 to end of list [ 7.752591] PM: Moving iio:iio:device0 to end of list
[ 58.703133] [DBGMSG] pca954x_irq_handler :entering pca954x_irq_handler [ 58.703975] [DBGMSG] pca954x_irq_handler :i2c_smbus_read::retval=0x14 [ 58.710540] [DBGMSG] pca954x_irq_handler :i=0x0 | bit: 0x4 isset in register = true [ 58.710543] [DBGMSG] pca954x_irq_handler :irq= 0x65 / child_irq =0xE7 [ 58.724634] [DBGMSG] handle_nested_irq :entering handle_nested_irq [ 58.724637] [DBGMSG] handle_nested_irq :irq: 0xE7 [ 58.724640] [DBGMSG] handle_nested_irq :irq_desc->name: null [ 58.724642] [DBGMSG] handle_nested_irq :irq_desc->parent_irq: 0x00 [ 58.724645] [DBGMSG] handle_nested_irq :irqd_irq_disabled: true [ 58.724645] [DBGMSG] handle_nested_irq :action: false or null [ 58.724647] [DBGMSG] handle_nested_irq :result of (unlikely(!action || irqd_irq_disabled(&desc->irq_data))) : true [ 58.724649] [DBGMSG] handle_nested_irq :goto out_unlock [ 58.724651] [DBGMSG] handle_nested_irq :leaving handler [ 58.724654] [DBGMSG] pca954x_irq_handler :leaving pca954x_irq_handler
root@testsystem:~# cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3 95: 0 0 0 0 gpio-mxc 0 Edge apds9960_event 101: 1 0 0 0 gpio-mxc 6 Edge pca954x
Regards,
Ralf Rademacher
Von: Laurent Pinchart <[email protected]>
Gesendet: Freitag, 10. Februar 2023 11:57
An: Rademacher Ralf
Cc: [email protected]
Betreff: #Extern_Re: AW: #Extern_Re: question about devicetree entry pca954x
Warnung: Achtung - Diese E-Mail stammt von einer externen Quelle. Seien Sie vorsichtig mit Links und Anhängen.
Warning: Attention - This e-mail is from an external source. Be careful with links and attachments.
Hello,
I'm sorry for the late reply, I've been very busy lately.
Quoted 8 lines · On Wed, Feb 08, 2023 at 03:56:15PM +0000, [email protected] wrote:
Hello Mr. Pinchart,
following on from our previous conversation, I have since observed the following.
The first call of
handle_nested_interrupt()during startup was a result of another driver and had nothing to do with the problem. i useddump_stack()to find the callee.
OK, that makes sense.
Quoted 21 lines
For the problem, the current debug output reduces to the following:
[ 28.830817] [DBGMSG]
pca954x_irq_handler:enteringpca954x_irq_handler[ 28.831363] [DBGMSG]pca954x_irq_handler:i2c_smbus_read::retval=14 [ 28.837918] [DBGMSG]pca954x_irq_handler:i=0 | bit: 4 isset in register = true [ 28.837921] [DBGMSG]pca954x_irq_handler:irq=0x65//child_irq=0xe7 [ 28.851527] [DBGMSG]handle_nested_irq:enteringhandle_nested_irq[ 28.851542] Call trace:
[ 28.851555]dump_backtrace+0x0/0x178
[ 28.851561]show_stack+0x24/0x30
[ 28.889839]dump_stack+0xb4/0x114
[ 28.893245]handle_nested_irq+0x44/0x23c
[ 28.897258]pca954x_irq_handler+0xf4/0x138[i2c_mux_pca954x]
[ 28.903006]irq_thread_fn+0x30/0xa0
[ 28.906581]irq_thread+0x150/0x248
[ 28.910068]kthread+0x140/0x160
[ 28.913297]ret_from_fork+0x10/0x1c
[ 28.916901] [DBGMSG]handle_nested_irq:irq:0xe7
[ 28.916905] [DBGMSG]handle_nested_irq:irq_desc->name: (null)
[ 28.921447] [DBGMSG]handle_nested_irq:irq_desc->parent_irq:0x0
Quoted 3 lines
Do you have any idea what the problem could be?
I have no idea about, why the interrupt is disabled and why the action of the threaded interrupt is null Is it possible that I have forgotten something in the DeviceTree entry?
Nothing immediately strikes me as wrong in your device tree.
Could you share the output of cat /proc/interrupts ? If the IRQ numbers listed in the log above (0x65 and 0xe7) have changed, please also share the new log, I want to correlate those numbers to /proc/interrupt entries.
Quoted 135 lines · Rademacher Ralf
Quoted 134 lines
Mr. Pinchart,
i have to correct myself:
the first call ofhandle_nested_interrupthappens already beforepca954x_probe. i added some more DBGMSGs[ 2.869856] [DBGMSG]
handle_nested_irq:irq =0xdf
[ 2.869858] [DBGMSG]handle_nested_irq:action =0x7ba41100
[ 2.874477] [DBGMSG]handle_nested_irq:irqd_irq_disabled(&desc->irq_data): false
[ 2.874479] [DBGMSG]handle_nested_irq:(unlikely(!action ||irqd_irq_disabled(&desc->irq_data))): false [ 2.874501] [DBGMSG]handle_nested_irq:action->irq:df | action->dev_id:0x7ba64810
[ 6.373737] [DBGMSG]pca954x_probe:enter fxn
[ 6.973918] [DBGMSG]pca954x_probe:leave fxnQuoted 118 lines · Rademacher Ralf
Quoted 85 lines · Laurent Pinchart
Quoted 84 lines · On Thu, Jan 26, 2023 at 05:05:47PM +0000, [email protected] wrote:
Hello Mr. Pinchart,
you are listed as maintainer in the
i2c-mux-pca954x.yamlfile.May I ask if you could take a few minutes and have a look at the following problem, if you can spot a bug in the second DT snippet?
Because on the internet you can only find examples where devices are used behind the pca954x which do not use an interrupt.
Let me tell you about the problem.
At our old device we had implemented this, which worked perfect:
&i2c4 {
pinctrl-names = "default","gpio";
pinctrl-0 = <&pinctrl_i2c4>;
pinctrl-1 = <&pinctrl_i2c4_gpio>;
sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; clock-frequency = <400000>;
status = "okay";touchscreen@26 {
compatible = "ilitek,ili2117";
reg = <0x26>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ili2117_62>; interrupt-parent = <&gpio2>;
interrupts = <7IRQ_TYPE_EDGE_RISING>; reset-gpios = <&pca9554_interface0GPIO_ACTIVE_LOW>; };proximity@39 {
compatible = "avago,apds9960"; reg = <0x39>;
pinctrl-names = "default"; pinctrl-0 = <&pinctrl_apds9960_39>; interrupt-parent = <&gpio2>; interrupts = <6IRQ_TYPE_EDGE_RISING>; };
.....Then we want more proximity sensors in this device, that we decided to add the PCA9544A.
&i2c4 {
.....
i2c4_mux_apds: i2c4-mux-pca9544@70 {
compatible = "nxp,pca9544";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x70>;
interrupt-parent = <&gpio2>;
interrupt-controller;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pca9544a_70>;
interrupts = <6IRQ_TYPE_EDGE_FALLING>;i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;proximity@39 {
compatible = "avago,apds9960"; reg = <0x39>;
interrupts = <0IRQ_TYPE_EDGE_FALLING>; interrupt-parent = <&i2c4_mux_apds>; };
};Both drivers (pca954x and apds9960) request threaded irqs in their probe function, but it does not work together. Although the apds9960 also gets one assigned, when the
handle_nested_irqfunction is called (After everything has been initialized. However, this seems to be the second call to this function! First call seems to be inside the initialization phase.) the irq seems to be disabled. And thus the processing does not start.Quoted 5 lines
Quoted 2 lines
I think that the problem is in my devicetree entry, that the soc doesn't really know how to handle the interrupt of the apds9960.
How are interrupts connected at the hardware level ? Is the APDS9960 interrupt connected to the INT0 pin of the PCA9544 ?
Yes, it is.
Quoted 2 lines
You have switched from
IRQ_TYPE_EDGE_RISINGtoIRQ_TYPE_EDGE_FALLINGfor the APDS9960, is that intentional ?Yes, I assumed this is correct, because APDS9960 datasheet tells me
that: "Interrupt open drain (active low)". So i thought i have to detect the falling edge, not the rising edge. The same in the datasheet of PCA9544A, there are 4 active low interrupt inputs.Quoted 3 lines
Is there any message printed to the kernel log around the time where either driver is probed, or when the APDS9960 interrupt is supposed to occur, that may indicate a problem ?
I have inserted some DBGMSGs into the functions
handle_nested_irqand in thepca954x_probe. during pca954x driver probe, there is the following output:[ 2.869856] [DBGMSG]
handle_nested_irq:irq =0xdf
[ 2.869858] [DBGMSG]handle_nested_irq:action =0x7ba41100
[ 2.874477] [DBGMSG]handle_nested_irq:irqd_irq_disabled(&desc->irq_data): false
[ 2.874479] [DBGMSG]handle_nested_irq:(unlikely(!action ||irqd_irq_disabled(&desc->irq_data))): false [ 2.874501] [DBGMSG]handle_nested_irq:action->irq:df | action->dev_id:0x7ba64810when a apds sends the interrupt signal to the pca954x, this happens:
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
[ 9336.607055] [DBGMSG] pca954x_irq_handler :pca954x_irq_handler starts [ 9336.607908] [DBGMSG] pca954x_irq_handler :i2c_smbus_read::retval=14 [ 9336.613255] [DBGMSG] pca954x_irq_handler :i=0 | bit: 4 is set in register [ 9336.619539] [DBGMSG] pca954x_irq_handler :irq= 0x65 // child_irq =0xe7 [ 9336.619542] [DBGMSG] handle_nested_irq :irq = 0xe7 [ 9336.632516] [DBGMSG] handle_nested_irq :action = 0x0 [ 9336.632519] [DBGMSG] handle_nested_irq :irqd_irq_disabled(&desc->irq_data):true [ 9336.632521] [DBGMSG] handle_nested_irq :(unlikely(!action || irqd_irq_disabled(&desc->irq_data))):true [ 9336.632523] [DBGMSG] handle_nested_irq :goto out_unlock
--
Regards,
Laurent Pinchart