i2c: designware: Add SMBus Quick Command support
Subsystems (3)
PATCH v2 1/1 i2c: designware: Add SMBus Quick Command support
From: Tan En De <[email protected]>
Add support for SMBus Quick Read and Quick Write commands.
---
v1 -> v2: Removed redundant check of tx_limit and rx_limit
--- drivers/i2c/busses/i2c-designware-core.h | 4 ++++ drivers/i2c/busses/i2c-designware-master.c | 18 +++++++++++++++++- 2 files changed, 21 insertions(+), 1 deletion(-)
drivers/i2c/busses/i2c-designware-core.h +4 -0
@@ -40,6 +40,8 @@#define DW_IC_DATA_CMD_DAT GENMASK(7, 0)#define DW_IC_DATA_CMD_FIRST_DATA_BYTE BIT(11) +#define DW_IC_DATA_CMD_STOP BIT(9) +#define DW_IC_DATA_CMD_CMD BIT(8)/* * Registers offset
@@ -123,7 +125,9 @@#define DW_IC_ERR_TX_ABRT 0x1 +#define DW_IC_TAR_SMBUS_QUICK_CMD BIT(16)#define DW_IC_TAR_10BITADDR_MASTER BIT(12) +#define DW_IC_TAR_SPECIAL BIT(11)#define DW_IC_COMP_PARAM_1_SPEED_MODE_HIGH (BIT(2) | BIT(3))#define DW_IC_COMP_PARAM_1_SPEED_MODE_MASK GENMASK(3, 2)
drivers/i2c/busses/i2c-designware-master.c +17 -1
@@ -268,6 +268,10 @@ static void i2c_dw_xfer_init(struct dw_i2c_dev *dev)regmap_update_bits (dev->map,DW_IC_CON ,DW_IC_CON_10BITADDR_MASTER , ic_con); +/* i2c-core-smbus.c: Only I2C_SMBUS_QUICK has msg[0].len = 0 */ +if (dev->msgs[0 ].len ==0 ) + ic_tar |=DW_IC_TAR_SMBUS_QUICK_CMD |DW_IC_TAR_SPECIAL ; +/* * Set the slave (target) address and enable 10-bit addressing mode * if applicable.
@@ -474,6 +478,16 @@ i2c_dw_xfer_msg(struct dw_i2c_dev *dev)regmap_read (dev->map,DW_IC_RXFLR , &flr); rx_limit = dev->rx_fifo_depth - flr; +/* i2c-core-smbus.c: Only I2C_SMBUS_QUICK has msg[0].len = 0 */ +if (buf_len ==0 ) { +regmap_write ( + dev->map,DW_IC_DATA_CMD , + *buf |DW_IC_DATA_CMD_STOP | + ((msgs[dev->msg_write_idx].flags &I2C_M_RD ) ? +DW_IC_DATA_CMD_CMD :0 ) + ); + } +while (buf_len >0 && tx_limit >0 && rx_limit >0 ) {u32 cmd =0 ;
@@ -919,7 +933,9 @@ void i2c_dw_configure_master(struct dw_i2c_dev *dev) {struct i2c_timings *t = &dev->timings; - dev->functionality =I2C_FUNC_10BIT_ADDR |DW_IC_DEFAULT_FUNCTIONALITY ; + dev->functionality =I2C_FUNC_10BIT_ADDR | +I2C_FUNC_SMBUS_QUICK | +DW_IC_DEFAULT_FUNCTIONALITY ; dev->master_cfg =DW_IC_CON_MASTER |DW_IC_CON_SLAVE_DISABLE |DW_IC_CON_RESTART_EN ;
Signature · 1 line
2.34.1
Andy Shevchenko
reviewerQuoted 3 lines · On Sat, Apr 12, 2025 at 05:34:14PM +0800, [email protected] wrote:
From: Tan En De <[email protected]>
Add support for SMBus Quick Read and Quick Write commands.
it's interesting how you made a versioning. Just rungit format-patch -v<X>... where <X> is the number of version you want, it will make it properly in the Subject.
...
Review
Quoted 1 line
(quoted diff) +1
-0+ /* i2c-core-smbus.c: Only I2C_SMBUS_QUICK has msg[0].len = 0 */
Please, remove filenames from the code, better to refer to the actual functions as func(). This helps also to grep for all usages in case of renaming.
...
Review
Quoted 1 line
(quoted diff) +1
-0+ /* i2c-core-smbus.c: Only I2C_SMBUS_QUICK has msg[0].len = 0 */
Ditto.
...
drivers/i2c/busses/i2c-designware-master.c i2c_dw_xfer_msg(struct dw_i2c_dev *dev) · line 484
Quoted 2 lines
drivers/i2c/busses/i2c-designware-master.c +2
-0+ regmap_write( + dev->map, DW_IC_DATA_CMD,
Something wrong with the indentation. And you have plenty of room on the previous line.
Quoted 4 lines
drivers/i2c/busses/i2c-designware-master.c +4
-0+ *buf |DW_IC_DATA_CMD_STOP | + ((msgs[dev->msg_write_idx].flags &I2C_M_RD ) ? +DW_IC_DATA_CMD_CMD :0 ) + );
...
drivers/i2c/busses/i2c-designware-master.c void i2c_dw_configure_master(struct dw_i2c_dev *dev) · line 938
Quoted 4 lines
drivers/i2c/busses/i2c-designware-master.c +3
-1- dev->functionality =I2C_FUNC_10BIT_ADDR |DW_IC_DEFAULT_FUNCTIONALITY ; + dev->functionality =I2C_FUNC_10BIT_ADDR | +I2C_FUNC_SMBUS_QUICK | +DW_IC_DEFAULT_FUNCTIONALITY ;
Ditto.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Quoted 5 lines
Review
Quoted 2 lines
(quoted diff) +1
-0+ /* i2c-core-smbus.c: Only I2C_SMBUS_QUICK has msg[0].len = 0 */Please, remove filenames from the code, better to refer to the actual functions as
func(). This helps also to grep for all usages in case of renaming.
The comment can be removed. Regular I2C messages can also have a length of 0.
Quoted 1 line
drivers/i2c/busses/i2c-designware-master.c void i2c_dw_configure_master(struct dw_i2c_dev *dev) · line 938
Quoted 1 line
drivers/i2c/busses/i2c-designware-master.c +1
-0+DW_IC_DEFAULT_FUNCTIONALITY ;
Sidenote: Why do we have this define? It is used only once and makes reading the actual functionalities harder, I'd say.
Also, I wonder if this patch really works in practice. The I2C_AQ_NO_ZERO_LEN flag is still set, so the core should prevent such messages to be passed on to the driver?
Quoted 2 lines
+#define
DW_IC_TAR_SMBUS_QUICK_CMDBIT(16)
This bit does not exist on the instance in the Renesas RZ/N1D SoC. So, this patch needs some versioning which HW can do this and which can't.
Quoted 6 lines · Wolfram Sang
Quoted 2 lines
+#define
DW_IC_TAR_SMBUS_QUICK_CMDBIT(16)This bit does not exist on the instance in the Renesas RZ/N1D SoC. So, this patch needs some versioning which HW can do this and which can't.
Yes, SMBUS features are only available starting from IP version 2.00a.
Hi
Quoted 17 lines · On 4/12/25 12:34 PM, [email protected] wrote:
From: Tan En De <[email protected]>
Add support for SMBus Quick Read and Quick Write commands.
Signed-off-by Tan En De <[email protected]>---
v1 -> v2: Removed redundant check oftx_limitandrx_limit--- drivers/i2c/busses/i2c-designware-core.h | 4 ++++ drivers/i2c/busses/i2c-designware-master.c | 18 +++++++++++++++++- 2 files changed, 21 insertions(+), 1 deletion(-)drivers/i2c/busses/i2c-designware-core.h +0
-0
drivers/i2c/busses/i2c-designware-core.h line 45
Quoted 6 lines
drivers/i2c/busses/i2c-designware-core.h +2
-0@@ -40,6 +40,8 @@#define DW_IC_DATA_CMD_DAT GENMASK(7, 0)#define DW_IC_DATA_CMD_FIRST_DATA_BYTE BIT(11) +#define DW_IC_DATA_CMD_STOP BIT(9) +#define DW_IC_DATA_CMD_CMD BIT(8)
If you like these defines would be nice to have in another patch before this and convert i2c-designware-master.c to use them instead of 0x100, BIT(9) and BIT(10) in existing code. Makes code more uniform together with your change.
I'm not demanding it but wanted to give you idea if you like to do some additional cleanups to the code :-)
As SMBus Quick Command support may depend on the IP version,
and given that it seems we are transitioning from dw_apb_i2c to dwc_i2c in the future, I think I shall leave this patch here for reference in case the dwc_i2c driver is upstreamed later.