Skip to contentSkip to conversation

board: rockchip: Add Pine64 Quartz64 and SOQuartz boards

PATCH Superseded Jonas Karlman 3 participants 26 messages Jul 23, 2023 – Jul 5, 2024

Subsystems (3)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

cover board: rockchip: Add Pine64 Quartz64 and SOQuartz boards

This series was created in collaboration with Nicolas Frattaroli and add support for Pine64 Quartz64 and SOQuartz boards with a RK3566 SoC.

- Pine64 Quartz64-A Board
- Pine64 Quartz64-B Board
- Pine64 SOQuartz on Model A
- Pine64 SOQuartz on Blade
- Pine64 SOQuartz on CM4-IO

Device trees have been imported from linux v6.4.

This series have loose dependencies on the following series:
- rockchip: Fix PCIe and NVMe support on RK3568 [1]
- rockchip: rk3568: Use dwc3-generic driver [2]
- rockchip: rk3568: Fix alloc space exhausted in SPL [3]
- rockchip: rk3568: Device Tree updates [4]
- rockchip: rk35xx: Fix SPI Flash alias [5]
- board: rockchip: Add Hardkernel ODROID-M1 [6]

A copy of this series with above dependencies can be found at [7].

[1] https://patchwork.ozlabs.org/project/uboot/list/?series=365195
[2] https://patchwork.ozlabs.org/project/uboot/list/?series=364127
[3] https://patchwork.ozlabs.org/project/uboot/list/?series=361999
[4] https://patchwork.ozlabs.org/project/uboot/list/?series=362030
[5] https://patchwork.ozlabs.org/project/uboot/list/?series=363527
[6] https://patchwork.ozlabs.org/project/uboot/list/?series=365198
[7] https://github.com/Kwiboo/u-boot-rockchip/commits/rk3568-quartz64-v1

Jonas Karlman (5):
board: rockchip: Add Pine64 Quartz64-A Board
board: rockchip: Add Pine64 Quartz64-B Board
board: rockchip: Add Pine64 SOQuartz on Model A
board: rockchip: Add Pine64 SOQuartz on Blade
board: rockchip: Add Pine64 SOQuartz on CM4-IO

 arch/arm/dts/Makefile                         |   5 +
 arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi    |  55 ++
 arch/arm/dts/rk3566-quartz64-a.dts            | 839 ++++++++++++++++++
 arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi    |  47 +
 arch/arm/dts/rk3566-quartz64-b.dts            | 739 +++++++++++++++
 .../arm/dts/rk3566-soquartz-blade-u-boot.dtsi |   3 +
 arch/arm/dts/rk3566-soquartz-blade.dts        | 194 ++++
 arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi  |   3 +
 arch/arm/dts/rk3566-soquartz-cm4.dts          | 192 ++++
 .../dts/rk3566-soquartz-model-a-u-boot.dtsi   |   3 +
 arch/arm/dts/rk3566-soquartz-model-a.dts      | 232 +++++
 arch/arm/dts/rk3566-soquartz-u-boot.dtsi      |  30 +
 arch/arm/dts/rk3566-soquartz.dtsi             | 688 ++++++++++++++
 arch/arm/mach-rockchip/rk3568/Kconfig         |   6 +
 board/pine64/quartz64_rk3566/Kconfig          |  15 +
 board/pine64/quartz64_rk3566/MAINTAINERS      |  23 +
 board/pine64/quartz64_rk3566/Makefile         |   3 +
 .../pine64/quartz64_rk3566/quartz64-rk3566.c  |   1 +
 configs/quartz64-a-rk3566_defconfig           | 110 +++
 configs/quartz64-b-rk3566_defconfig           | 106 +++
 configs/soquartz-blade-rk3566_defconfig       |  90 ++
 configs/soquartz-cm4-rk3566_defconfig         |  90 ++
 configs/soquartz-model-a-rk3566_defconfig     |  90 ++
 doc/board/rockchip/rockchip.rst               |   5 +
 include/configs/quartz64_rk3566.h             |  10 +
 25 files changed, 3579 insertions(+)
 create mode 100644 arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
 create mode 100644 arch/arm/dts/rk3566-quartz64-a.dts
 create mode 100644 arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi
 create mode 100644 arch/arm/dts/rk3566-quartz64-b.dts
 create mode 100644 arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi
 create mode 100644 arch/arm/dts/rk3566-soquartz-blade.dts
 create mode 100644 arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi
 create mode 100644 arch/arm/dts/rk3566-soquartz-cm4.dts
 create mode 100644 arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
 create mode 100644 arch/arm/dts/rk3566-soquartz-model-a.dts
 create mode 100644 arch/arm/dts/rk3566-soquartz-u-boot.dtsi
 create mode 100644 arch/arm/dts/rk3566-soquartz.dtsi
 create mode 100644 board/pine64/quartz64_rk3566/Kconfig
 create mode 100644 board/pine64/quartz64_rk3566/MAINTAINERS
 create mode 100644 board/pine64/quartz64_rk3566/Makefile
 create mode 100644 board/pine64/quartz64_rk3566/quartz64-rk3566.c
 create mode 100644 configs/quartz64-a-rk3566_defconfig
 create mode 100644 configs/quartz64-b-rk3566_defconfig
 create mode 100644 configs/soquartz-blade-rk3566_defconfig
 create mode 100644 configs/soquartz-cm4-rk3566_defconfig
 create mode 100644 configs/soquartz-model-a-rk3566_defconfig
 create mode 100644 include/configs/quartz64_rk3566.h
Signature · 1 line
2.41.0
#1 lore raw

PATCH 1/5 board: rockchip: Add Pine64 Quartz64-A Board

The Pine64 Quartz64 Model A is a single-board computer based on the Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0, CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a 20 pin GPIO header.

Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Device tree is imported from linux v6.4.

---
 arch/arm/dts/Makefile                         |   1 +
 arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi    |  55 ++
 arch/arm/dts/rk3566-quartz64-a.dts            | 839 ++++++++++++++++++
 arch/arm/mach-rockchip/rk3568/Kconfig         |   6 +
 board/pine64/quartz64_rk3566/Kconfig          |  15 +
 board/pine64/quartz64_rk3566/MAINTAINERS      |   9 +
 board/pine64/quartz64_rk3566/Makefile         |   3 +
 .../pine64/quartz64_rk3566/quartz64-rk3566.c  |   1 +
 configs/quartz64-a-rk3566_defconfig           | 110 +++
 doc/board/rockchip/rockchip.rst               |   1 +
 include/configs/quartz64_rk3566.h             |  10 +
 11 files changed, 1050 insertions(+)
 create mode 100644 arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
 create mode 100644 arch/arm/dts/rk3566-quartz64-a.dts
 create mode 100644 board/pine64/quartz64_rk3566/Kconfig
 create mode 100644 board/pine64/quartz64_rk3566/MAINTAINERS
 create mode 100644 board/pine64/quartz64_rk3566/Makefile
 create mode 100644 board/pine64/quartz64_rk3566/quartz64-rk3566.c
 create mode 100644 configs/quartz64-a-rk3566_defconfig
 create mode 100644 include/configs/quartz64_rk3566.h
arch/arm/dts/Makefile +1 -0
index 6764ded580ab..45ef73fdf0ca 100644
@@ -167,6 +167,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \
 
 dtb-$(CONFIG_ROCKCHIP_RK3568) += \
 	rk3566-anbernic-rgxx3.dtb \
+	rk3566-quartz64-a.dtb \
 	rk3566-radxa-cm3-io.dtb \
 	rk3568-evb.dtb \
 	rk3568-odroid-m1.dtb \
arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi new file +55 -0

55 lines not on this page · raw message

arch/arm/dts/rk3566-quartz64-a.dts new file +839 -0

839 lines not on this page · raw message

arch/arm/mach-rockchip/rk3568/Kconfig +6 -0
index f46be3d081fe..baa51349f4be 100644
@@ -22,6 +22,11 @@ config TARGET_ODROID_M1_RK3568
 	help
 	  Hardkernel ODROID-M1 single board computer with a RK3568B2 SoC.
 
+config TARGET_QUARTZ64_RK3566
+	bool "Pine64 Quartz64"
+	help
+	  Pine64 Quartz64 single board computer with a RK3566 SoC.
+
 endchoice
 
 config ROCKCHIP_BOOT_MODE_REG
@@ -39,5 +44,6 @@ config SYS_MALLOC_F_LEN
 source "board/rockchip/evb_rk3568/Kconfig"
 source "board/anbernic/rgxx3_rk3566/Kconfig"
 source "board/hardkernel/odroid_m1/Kconfig"
+source "board/pine64/quartz64_rk3566/Kconfig"
 
 endif
board/pine64/quartz64_rk3566/Kconfig new file +15 -0
new file mode 100644
index 000000000000..3de1d8f7a993
@@ -0,0 +1,15 @@
+if TARGET_QUARTZ64_RK3566
+
+config SYS_BOARD
+	default "quartz64_rk3566"
+
+config SYS_VENDOR
+	default "pine64"
+
+config SYS_CONFIG_NAME
+	default "quartz64_rk3566"
+
+config BOARD_SPECIFIC_OPTIONS # dummy
+	def_bool y
+
+endif
board/pine64/quartz64_rk3566/MAINTAINERS new file +9 -0
new file mode 100644
index 000000000000..dbc0dfbd9787
@@ -0,0 +1,9 @@
+QUARTZ64-RK3566
+M:	Nicolas Frattaroli <[email protected]>
+R:	Jonas Karlman <[email protected]>
+S:	Maintained
+F:	board/pine64/quartz64_rk3566/
+F:	include/configs/quartz64_rk3566.h
+F:	configs/quartz64-a-rk3566_defconfig
+F:	arch/arm/dts/rk3566-quartz64-a.dts
+F:	arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
board/pine64/quartz64_rk3566/Makefile new file +3 -0
new file mode 100644
index 000000000000..c24a40e724d7
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+obj-y	+= quartz64-rk3566.o
board/pine64/quartz64_rk3566/quartz64-rk3566.c new file +1 -0
new file mode 100644
index 000000000000..4c027f2a7af9
@@ -0,0 +1 @@
+// SPDX-License-Identifier: GPL-2.0+
configs/quartz64-a-rk3566_defconfig new file +110 -0

110 lines not on this page · raw message

doc/board/rockchip/rockchip.rst +1 -0
index b89f35954d33..c7d4c835db80 100644
@@ -96,6 +96,7 @@ List of mainline supported Rockchip boards:
 * rk3568
      - Rockchip Evb-RK3568 (evb-rk3568)
      - Hardkernel ODROID-M1 (odroid-m1-rk3568)
+     - Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig)
 
 * rk3588
      - Rockchip EVB (evb-rk3588)
include/configs/quartz64_rk3566.h new file +10 -0
new file mode 100644
index 000000000000..dfe0fee94cdb
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+
+#ifndef __QUARTZ64_RK3566_H
+#define __QUARTZ64_RK3566_H
+
+#define ROCKCHIP_DEVICE_SETTINGS
+
+#include <configs/rk3568_common.h>
+
+#endif
Signature · 1 line
2.41.0
#2 lore raw

Re: [PATCH 1/5] board: rockchip: Add Pine64 Quartz64-A Board

Quoted 11 lines · Jonas Karlman

The Pine64 Quartz64 Model A is a single-board computer based on the Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0, CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a 20 pin GPIO header.

Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Quoted 6 lines

Device tree is imported from linux v6.4.

---

[...]

Boot log with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf:

DDR V1.17 992b933606 typ 23/04/25-10:10:19
ln
LP4/4x derate en, other dram:1x trefi
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=8 Size=8192MB
tdqss: cs0 dqs0: 72ps, dqs1: -96ps, dqs2: -48ps, dqs3: -144ps,
tdqss: cs1 dqs0: 48ps, dqs1: -96ps, dqs2: -48ps, dqs3: -120ps,

change to: 324MHz
clk skew:0x61

change to: 528MHz
clk skew:0x58

change to: 780MHz
clk skew:0x58

change to: 1056MHz(final freq)
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:22%
dram drv:40,odt:80
vref_ca:00000071
clk skew:0x2f
cs 0:
the read training result:
DQS0:0x3e, DQS1:0x3d, DQS2:0x42, DQS3:0x3a,

min  : 0xd  0xe  0xe  0xd  0x1  0x2  0x5  0x1 , 0x6  0x7  0x2  0x1  0xa  0x9  0xe  0x9 ,
      0x10  0xf  0xe  0xa  0x6  0x1  0x1  0x4 , 0xb  0x8  0x4  0x1  0xd  0xa  0x9  0xc ,
mid  :0x2b 0x2c 0x2d 0x2c 0x20 0x22 0x24 0x20 ,0x26 0x26 0x22 0x20 0x2a 0x29 0x2c 0x29 ,
      0x30 0x2f 0x2d 0x29 0x25 0x20 0x21 0x23 ,0x2a 0x26 0x24 0x20 0x2c 0x29 0x28 0x2b ,
max  :0x49 0x4a 0x4d 0x4c 0x40 0x42 0x43 0x40 ,0x46 0x46 0x43 0x40 0x4b 0x49 0x4b 0x49 ,
      0x51 0x50 0x4c 0x49 0x45 0x3f 0x41 0x43 ,0x49 0x45 0x44 0x40 0x4c 0x49 0x47 0x4a ,
range:0x3c 0x3c 0x3f 0x3f 0x3f 0x40 0x3e 0x3f ,0x40 0x3f 0x41 0x3f 0x41 0x40 0x3d 0x40 ,
      0x41 0x41 0x3e 0x3f 0x3f 0x3e 0x40 0x3f ,0x3e 0x3d 0x40 0x3f 0x3f 0x3f 0x3e 0x3e ,
the write training result:
DQS0:0x38, DQS1:0x23, DQS2:0x29, DQS3:0x1c,
min  :0x64 0x67 0x68 0x68 0x5b 0x5d 0x5f 0x64 0x62 ,0x4c 0x4d 0x48 0x48 0x50 0x50 0x52 0x50 0x4e ,
      0x54 0x53 0x51 0x50 0x4c 0x4a 0x4a 0x4e 0x4f ,0x47 0x46 0x44 0x41 0x4a 0x4a 0x48 0x4c 0x45 ,
mid  :0x81 0x83 0x84 0x83 0x77 0x79 0x7c 0x7d 0x7c ,0x6a 0x6a 0x64 0x63 0x6c 0x6b 0x6c 0x6b 0x69 ,
      0x72 0x71 0x6d 0x6d 0x68 0x61 0x62 0x69 0x6a ,0x65 0x60 0x5f 0x5c 0x65 0x66 0x61 0x68 0x60 ,
max  :0x9e 0xa0 0xa1 0x9e 0x93 0x95 0x99 0x96 0x96 ,0x88 0x87 0x81 0x7e 0x88 0x87 0x87 0x87 0x85 ,
      0x90 0x8f 0x89 0x8a 0x84 0x79 0x7b 0x85 0x86 ,0x83 0x7b 0x7a 0x77 0x81 0x82 0x7b 0x85 0x7c ,
range:0x3a 0x39 0x39 0x36 0x38 0x38 0x3a 0x32 0x34 ,0x3c 0x3a 0x39 0x36 0x38 0x37 0x35 0x37 0x37 ,
      0x3c 0x3c 0x38 0x3a 0x38 0x2f 0x31 0x37 0x37 ,0x3c 0x35 0x36 0x36 0x37 0x38 0x33 0x39 0x37 ,
cs 1:
the read training result:
DQS0:0x3c, DQS1:0x3d, DQS2:0x42, DQS3:0x3b,
min  : 0xc  0xc  0xd  0xc  0x1  0x2  0x6  0x3 , 0x7  0x7  0x2  0x1  0x9  0x9  0xd  0x9 ,
      0x10  0xf  0xe  0xb  0x7  0x1  0x2  0x5 , 0xa  0x9  0x6  0x1  0xd  0xc  0xb  0xe ,
mid  :0x29 0x2a 0x2c 0x2a 0x20 0x21 0x24 0x20 ,0x26 0x26 0x22 0x21 0x2a 0x29 0x2c 0x28 ,
      0x2f 0x2e 0x2c 0x2a 0x26 0x20 0x21 0x24 ,0x29 0x27 0x26 0x21 0x2d 0x2c 0x2a 0x2d ,
max  :0x47 0x48 0x4b 0x49 0x3f 0x41 0x43 0x3e ,0x46 0x46 0x42 0x41 0x4b 0x49 0x4b 0x48 ,
      0x4f 0x4e 0x4a 0x49 0x45 0x40 0x41 0x44 ,0x49 0x46 0x46 0x41 0x4d 0x4c 0x49 0x4d ,
range:0x3b 0x3c 0x3e 0x3d 0x3e 0x3f 0x3d 0x3b ,0x3f 0x3f 0x40 0x40 0x42 0x40 0x3e 0x3f ,
      0x3f 0x3f 0x3c 0x3e 0x3e 0x3f 0x3f 0x3f ,0x3f 0x3d 0x40 0x40 0x40 0x40 0x3e 0x3f ,
the write training result:
DQS0:0x38, DQS1:0x23, DQS2:0x29, DQS3:0x1c,
min  :0x62 0x64 0x65 0x64 0x57 0x59 0x5d 0x5f 0x5c ,0x4b 0x4c 0x46 0x46 0x4e 0x4e 0x52 0x4f 0x4c ,
      0x54 0x53 0x4f 0x4f 0x4b 0x47 0x49 0x4e 0x4e ,0x4a 0x4a 0x48 0x44 0x4e 0x4c 0x4b 0x4f 0x49 ,
mid  :0x7f 0x80 0x81 0x80 0x74 0x76 0x7a 0x7a 0x78 ,0x68 0x68 0x62 0x61 0x69 0x69 0x6c 0x6a 0x68 ,
      0x71 0x70 0x6b 0x6b 0x65 0x5f 0x62 0x67 0x69 ,0x68 0x65 0x61 0x5f 0x69 0x69 0x64 0x6c 0x63 ,
max  :0x9c 0x9d 0x9e 0x9c 0x91 0x94 0x97 0x95 0x94 ,0x86 0x84 0x7e 0x7c 0x85 0x85 0x86 0x85 0x84 ,
      0x8f 0x8d 0x88 0x88 0x80 0x78 0x7b 0x80 0x85 ,0x87 0x81 0x7a 0x7a 0x84 0x87 0x7d 0x89 0x7e ,
range:0x3a 0x39 0x39 0x38 0x3a 0x3b 0x3a 0x36 0x38 ,0x3b 0x38 0x38 0x36 0x37 0x37 0x34 0x36 0x38 ,
      0x3b 0x3a 0x39 0x39 0x35 0x31 0x32 0x32 0x37 ,0x3d 0x37 0x32 0x36 0x36 0x3b 0x32 0x3a 0x35 ,
CA Training result:
cs:0 min  :0x51 0x50 0x4a 0x43 0x49 0x43 0x4c ,0x4e 0x49 0x48 0x42 0x47 0x3f 0x49 ,
cs:0 mid  :0x8f 0x91 0x84 0x84 0x84 0x84 0x7b ,0x8a 0x89 0x83 0x82 0x82 0x80 0x78 ,
cs:0 max  :0xcd 0xd2 0xbf 0xc6 0xc0 0xc5 0xab ,0xc6 0xc9 0xbf 0xc2 0xbd 0xc1 0xa7 ,
cs:0 range:0x7c 0x82 0x75 0x83 0x77 0x82 0x5f ,0x78 0x80 0x77 0x80 0x76 0x82 0x5e ,
cs:1 min  :0x4e 0x53 0x45 0x45 0x45 0x45 0x4a ,0x4a 0x4c 0x44 0x46 0x42 0x43 0x48 ,
cs:1 mid  :0x8e 0x90 0x84 0x83 0x84 0x81 0x7b ,0x8a 0x88 0x84 0x83 0x83 0x80 0x78 ,
cs:1 max  :0xcf 0xcd 0xc4 0xc1 0xc3 0xbe 0xad ,0xcb 0xc5 0xc4 0xc0 0xc4 0xbe 0xa9 ,

cs:1 range:0x81 0x7a 0x7f 0x7c 0x7e 0x79 0x63 ,0x81 0x79 0x80 0x7a 0x82 0x7b 0x61 , out

U-Boot SPL 2023.07 (Jul 23 2023 - 12:42:18 +0000) rockchip_sdhci_probe clk set rate fail! Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK ## Checking hash(es) for Image atf-1 ... sha256+ OK ## Checking hash(es) for Image u-boot ... sha256+ OK ## Checking hash(es) for Image fdt-1 ... sha256+ OK ## Checking hash(es) for Image atf-2 ... sha256+ OK ## Checking hash(es) for Image atf-3 ... sha256+ OK ## Checking hash(es) for Image atf-4 ... sha256+ OK ## Checking hash(es) for Image atf-5 ... sha256+ OK ## Checking hash(es) for Image atf-6 ... sha256+ OK

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-607-gbf602aff1:cl
NOTICE:  BL31: Built : 10:16:03, Jun  5 2023
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    pmu v1 is valid 220114
INFO:    dfs DDR fsp_param[0].freq_mhz= 1056MHz
INFO:    dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO:    dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO:    dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0xa00000
INFO:    SPSR = 0x3c9

U-Boot 2023.07 (Jul 23 2023 - 12:42:18 +0000)

Model: Pine64 RK3566 Quartz64-A Board
DRAM:  8 GiB (effective 7.7 GiB)
PMIC:  RK8170 (on=0x10, off=0x00)
Core:  321 devices, 27 uclasses, devicetree: separate
MMC:   rockchip_sdhci_probe clk set rate fail!
mmc@fe2b0000: 1, mmc@fe2c0000: 2, mmc@fe310000: 0
Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: Pine64 RK3566 Quartz64-A Board
Net:   No ethernet found.

Hit any key to stop autoboot: 0
=>

Regards,
Jonas

#3 lore raw

Re: [PATCH 1/5] board: rockchip: Add Pine64 Quartz64-A Board

Hi Jonas,

Quoted 41 lines · Jonas Karlman
Quoted 11 lines · Jonas Karlman

The Pine64 Quartz64 Model A is a single-board computer based on the Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0, CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a 20 pin GPIO header.

Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Quoted 6 lines

Device tree is imported from linux v6.4.

---

[...]

Boot log with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf:

[...]

U-Boot 2023.07 (Jul 23 2023 - 12:42:18 +0000)

Model: Pine64 RK3566 Quartz64-A Board
DRAM:  8 GiB (effective 7.7 GiB)
PMIC:  RK8170 (on=0x10, off=0x00)
Core:  321 devices, 27 uclasses, devicetree: separate MMC:   rockchip_sdhci_probe clk set rate fail! mmc@fe2b0000: 1, mmc@fe2c0000: 2, mmc@fe310000: 0 Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: Pine64 RK3566 Quartz64-A Board
Net:   No ethernet found.

Quoted 2 lines

Hit any key to stop autoboot:  0
=>

I just tried booting U-Boot v2023.10-rc2 with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf, on my Quartz64-A but it fails during loading of some parts. I removed the output of the RK TPL from my logs as there were no errors.

This is when booting from eMMC.

I also tried building your branch from https://github.com/Kwiboo/u-boot-rockchip/tree/rk3568-2023.10 and

The full build commands:

export ROCKCHIP_TPL=rkbin/bin/rk35/rk3566_ddr_1056MHz_v1.17.bin export BL31=rkbin/bin/rk35/rk3568_bl31_v1.43.elf
make quartz64-a-rk3566_defconfig
make -j16

rkdeveloptool db rk356x_spl_loader_v1.13.112.bin
rkdeveloptool wl 64 u-boot-rockchip.bin

Boot log (v2023.10-rc2):

U-Boot SPL 2023.10-rc2 (Aug 08 2023 - 14:02:34 +0100) rockchip_sdhci_probe clk set rate fail!
Trying to boot from MMC1
spl: mmc init failed with error: -110
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 0 (ret = -5)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Boot log (your branch):

U-Boot SPL 2023.10-rc1-00368-g16cb31d427 (Aug 08 2023 - 15:17:35 +0100) Trying to boot from MMC1
spl: mmc init failed with error: -70
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Thanks!

Chris

#4 lore raw

Re: [PATCH 1/5] board: rockchip: Add Pine64 Quartz64-A Board

Hi Christopher,

Quoted 44 lines · Christopher Obbard

Hi Jonas,

Quoted 41 lines · Jonas Karlman
Quoted 11 lines · Jonas Karlman

The Pine64 Quartz64 Model A is a single-board computer based on the Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0, CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a 20 pin GPIO header.

Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Quoted 6 lines

Device tree is imported from linux v6.4.

---

[...]

Boot log with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf:

[...]

U-Boot 2023.07 (Jul 23 2023 - 12:42:18 +0000)

Model: Pine64 RK3566 Quartz64-A Board
DRAM:  8 GiB (effective 7.7 GiB)
PMIC:  RK8170 (on=0x10, off=0x00)
Core:  321 devices, 27 uclasses, devicetree: separate MMC:   rockchip_sdhci_probe clk set rate fail! mmc@fe2b0000: 1, mmc@fe2c0000: 2, mmc@fe310000: 0 Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: Pine64 RK3566 Quartz64-A Board
Net:   No ethernet found.

Quoted 6 lines
Quoted 2 lines

Hit any key to stop autoboot:  0
=>

I just tried booting U-Boot v2023.10-rc2 with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf, on my Quartz64-A but it fails during loading of some parts. I removed the output of the RK TPL from my logs as there were no errors.

Try with latest rk3566_ddr_1056MHz_v1.18.bin and see if that makes any difference.

Quoted 2 lines

This is when booting from eMMC.

Does it boot with SD-card or other eMMC modules?

Quoted 2 lines

I also tried building your branch from https://github.com/Kwiboo/u-boot-rockchip/tree/rk3568-2023.10 and

Please try with a GitHub actions built u-boot-rockchip.bin based on my rk3568-2023.07.02 branch at
https://github.com/Kwiboo/u-boot-build/actions/runs/5777761235

Quoted 11 lines

The full build commands:

export ROCKCHIP_TPL=rkbin/bin/rk35/rk3566_ddr_1056MHz_v1.17.bin export BL31=rkbin/bin/rk35/rk3568_bl31_v1.43.elf
make quartz64-a-rk3566_defconfig
make -j16

rkdeveloptool db rk356x_spl_loader_v1.13.112.bin
rkdeveloptool wl 64 u-boot-rockchip.bin

What happens if you write u-boot-rockchip.bin to eMMC module usinga USB adapter:

dd if=u-boot-rockchip.bin of=/dev/<device> bs=32k seek=1 conv=fsync

or using U-Boot cmd when booted from a SD-card?

# Read u-boot-rockchip.bin from first partition of a SD card load mmc 1:1 10000000 u-boot-rockchip.bin

# Change to eMMC
mmc dev 0

# Write 10 MiB (0x5000 blocks) at sector 64 (0x40) mmc write $fileaddr 40 5000

Does that make any difference?

Quoted 11 lines

Boot log (v2023.10-rc2):

U-Boot SPL 2023.10-rc2 (Aug 08 2023 - 14:02:34 +0100) rockchip_sdhci_probe clk set rate fail! Trying to boot from MMC1
spl: mmc init failed with error: -110
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1

Strange that second try of eMMC (MMC1) gets little bit longer.

Quoted 10 lines

## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 0 (ret = -5)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Boot log (your branch):

Quoted 11 lines

U-Boot SPL 2023.10-rc1-00368-g16cb31d427 (Aug 08 2023 - 15:17:35 +0100) Trying to boot from MMC1
spl: mmc init failed with error: -70
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

I have not been able to reproduce this kind of issue on any of my two Quartz64-A boards, tested with different eMMC modules.

Does your eMMC module have some compatibility issue?
Do you have any more details on the eMMC module you have tested with?

There was also some clk and pinctrl changes recently merged into master branch, but they was probably included in the build from my branch based on the lack of "rockchip_sdhci_probe clk set rate fail!" message.

Regards,
Jonas

Quoted 6 lines

Thanks!

Chris

#5 lore raw

Re: [PATCH 1/5] board: rockchip: Add Pine64 Quartz64-A Board

Hi Jonas,

Sorry for the late response, I've been meaning to test this for a while but not got around to it.

Quoted 51 lines · Jonas Karlman

Hi Christopher,

Quoted 48 lines · Christopher Obbard

Hi Jonas,

Quoted 43 lines · Jonas Karlman
Quoted 11 lines · Jonas Karlman

The Pine64 Quartz64 Model A is a single-board computer based on the Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0, CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a 20 pin GPIO header.

Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Quoted 6 lines

Device tree is imported from linux v6.4.

---

[...]

Boot log with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf:

[...]

U-Boot 2023.07 (Jul 23 2023 - 12:42:18 +0000)

Model: Pine64 RK3566 Quartz64-A Board
DRAM:  8 GiB (effective 7.7 GiB)
PMIC:  RK8170 (on=0x10, off=0x00)
Core:  321 devices, 27 uclasses, devicetree: separate MMC:   rockchip_sdhci_probe clk set rate fail! mmc@fe2b0000: 1, mmc@fe2c0000: 2, mmc@fe310000: 0 Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: Pine64 RK3566 Quartz64-A Board
Net:   No ethernet found.

Hit any key to stop autoboot:  0
=>

Quoted 5 lines
Quoted 2 lines

I just tried booting U-Boot v2023.10-rc2 with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf, on my Quartz64-A but it fails during loading of some parts. I removed the output of the RK TPL from my logs as there were no errors.

Try with latest rk3566_ddr_1056MHz_v1.18.bin and see if that makes any difference.

No difference.

I've also checked, there is no other maskrom bootable media such as SPI flash connected to the board.

Quoted 4 lines
Quoted 2 lines

This is when booting from eMMC.

Does it boot with SD-card or other eMMC modules?

Booting from SD card (without eMMC connected), everything works fine.

Quoted 7 lines
Quoted 3 lines

I also tried building your branch from https://github.com/Kwiboo/u-boot-rockchip/tree/rk3568-2023.10 and

Please try with a GitHub actions built u-boot-rockchip.bin based on my rk3568-2023.07.02 branch at
https://github.com/Kwiboo/u-boot-build/actions/runs/5777761235

With that exact artifact, flashed with:

Quoted 4 lines

rkdeveloptool db rk356x_spl_loader_v1.18.113.bin
rkdeveloptool ef
rkdeveloptool wl 64 u-boot-rockchip.bin
rkdeveloptool rd

it fails to boot with with:

Quoted 21 lines

DDR V1.18 f366f69a7d typ 23/07/17-15:48:58
ln
LP4/4x derate en, other dram:1x trefi
SRX
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=8 Size=8192MB

change to: 324MHz
clk skew:0x60

change to: 528MHz
clk skew:0x58

change to: 780MHz
clk skew:0x58

change to: 1056MHz(final freq)
clk skew:0x32
out

Quoted 11 lines

U-Boot SPL 2023.07.02-g09919887 (Aug 06 2023 - 16:59:31 +0000) Trying to boot from MMC1
spl: mmc init failed with error: -70
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc fail to send stop cmd
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

I also tried a second eMMC, but it also failed to boot with the same "mmc block read error" message.

Quoted 10 lines

What happens if you write u-boot-rockchip.bin to eMMC module usinga USB adapter:

  dd if=u-boot-rockchip.bin of=/dev/<device> bs=32k seek=1 conv=fsync

or using U-Boot cmd when booted from a SD-card?

  # Read u-boot-rockchip.bin from first partition of a SD card load mmc 1:1 10000000 u-boot-rockchip.bin

Quoted 7 lines

  # Change to eMMC
  mmc dev 0

  # Write 10 MiB (0x5000 blocks) at sector 64 (0x40) mmc write $fileaddr 40 5000

Does that make any difference?

I don't think I have an eMMC writer for Pine64 eMMCs, I will try to get hold of one this week. But it fails to write to the eMMC with:

Quoted 21 lines

=> load mmc 1:2 10000000 u-boot-rockchip.bin
9510400 bytes read in 791 ms (11.5 MiB/s)

=> mmc dev 0
switch to partitions #0, OK
mmc0(part 0) is current device

=> mmc write $fileaddr 40 5000
MMC write: dev # 0, block # 64, count 20480 ... mmc write failed 0 blocks written: ERROR

=> mmc info
Device: mmc@fe310000
Manufacturer ID: 45
OEM: 0
Name: DF4016
Bus Speed: 52000000
Mode: MMC DDR52 (52MHz)
Rd Block Len: 512
MMC version 5.1

Quoted 8 lines

High Capacity: Yes
Capacity: 14.7 GiB
Bus Width: 8-bit DDR
Erase Group Size: 512 KiB
HC WP Group Size: 8 MiB
User Capacity: 14.7 GiB WRREL
Boot Capacity: 4 MiB ENH
RPMB Capacity: 4 MiB ENH

I think this points to some issue with the mmc driver in U-Boot, or possibly some issue with my board. But I find that hard to believe because the Rockchip usbloader seems to write to the eMMC just fine ?

Quoted 37 lines
Quoted 4 lines

Boot log (v2023.10-rc2):

Quoted 8 lines

U-Boot SPL 2023.10-rc2 (Aug 08 2023 - 14:02:34 +0100) rockchip_sdhci_probe clk set rate fail! Trying to boot from MMC1
spl: mmc init failed with error: -110
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1

Strange that second try of eMMC (MMC1) gets little bit longer.

Quoted 10 lines

## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 0 (ret = -5)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Boot log (your branch):

Quoted 11 lines

U-Boot SPL 2023.10-rc1-00368-g16cb31d427 (Aug 08 2023 - 15:17:35 +0100) Trying to boot from MMC1
spl: mmc init failed with error: -70
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Quoted 5 lines

I have not been able to reproduce this kind of issue on any of my two Quartz64-A boards, tested with different eMMC modules.

Does your eMMC module have some compatibility issue?
Do you have any more details on the eMMC module you have tested with?

I have two eMMCs, one from FORESEE which came with a Pine64 and one marked SanDisk (which I posted the mmc info for above).

My hardware is marked Quartz64-RK3399-V2.0 2021-04-27 Maybe there is some difference with your board?

I will also try an image with vendor u-boot as a next step.

Quoted 3 lines

There was also some clk and pinctrl changes recently merged into master branch, but they was probably included in the build from my branch based on the lack of "rockchip_sdhci_probe clk set rate fail!" message.

I tried with your build, but I will investigate more with master.

Thanks!

Chris

#6 lore raw

Re: [PATCH 1/5] board: rockchip: Add Pine64 Quartz64-A Board

Hi Jonas,

Quoted 123 lines · Christopher Obbard

Hi Jonas,

Sorry for the late response, I've been meaning to test this for a while but not got around to it.

Quoted 51 lines · Jonas Karlman

Hi Christopher,

Quoted 48 lines · Christopher Obbard

Hi Jonas,

Quoted 43 lines · Jonas Karlman
Quoted 11 lines · Jonas Karlman

The Pine64 Quartz64 Model A is a single-board computer based on the Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0, CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a 20 pin GPIO header.

Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Quoted 6 lines

Device tree is imported from linux v6.4.

---

[...]

Boot log with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf:

[...]

U-Boot 2023.07 (Jul 23 2023 - 12:42:18 +0000)

Model: Pine64 RK3566 Quartz64-A Board
DRAM:  8 GiB (effective 7.7 GiB)
PMIC:  RK8170 (on=0x10, off=0x00)
Core:  321 devices, 27 uclasses, devicetree: separate MMC:   rockchip_sdhci_probe clk set rate fail! mmc@fe2b0000: 1, mmc@fe2c0000: 2, mmc@fe310000: 0 Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: Pine64 RK3566 Quartz64-A Board
Net:   No ethernet found.

Hit any key to stop autoboot:  0
=>

Quoted 5 lines
Quoted 2 lines

I just tried booting U-Boot v2023.10-rc2 with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf, on my Quartz64-A but it fails during loading of some parts. I removed the output of the RK TPL from my logs as there were no errors.

Try with latest rk3566_ddr_1056MHz_v1.18.bin and see if that makes any difference.

No difference.

I've also checked, there is no other maskrom bootable media such as SPI flash connected to the board.

Quoted 4 lines
Quoted 2 lines

This is when booting from eMMC.

Does it boot with SD-card or other eMMC modules?

Booting from SD card (without eMMC connected), everything works fine.

Quoted 7 lines
Quoted 3 lines

I also tried building your branch from https://github.com/Kwiboo/u-boot-rockchip/tree/rk3568-2023.10 and

Please try with a GitHub actions built u-boot-rockchip.bin based on my rk3568-2023.07.02 branch at
https://github.com/Kwiboo/u-boot-build/actions/runs/5777761235

With that exact artifact, flashed with:

Quoted 4 lines

rkdeveloptool db rk356x_spl_loader_v1.18.113.bin
rkdeveloptool ef
rkdeveloptool wl 64 u-boot-rockchip.bin
rkdeveloptool rd

it fails to boot with with:

Quoted 21 lines

DDR V1.18 f366f69a7d typ 23/07/17-15:48:58
ln
LP4/4x derate en, other dram:1x trefi
SRX
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=8 Size=8192MB

change to: 324MHz
clk skew:0x60

change to: 528MHz
clk skew:0x58

change to: 780MHz
clk skew:0x58

change to: 1056MHz(final freq)
clk skew:0x32
out

Quoted 11 lines

U-Boot SPL 2023.07.02-g09919887 (Aug 06 2023 - 16:59:31 +0000) Trying to boot from MMC1
spl: mmc init failed with error: -70
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc fail to send stop cmd
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Quoted 1 line

I also tried a second eMMC, but it also failed to boot with the same "mmc block read error" message.

I tried with your latest branch https://github.com/Kwiboo/u-boot-rockchip/commits/rk3568-2023.10

and this time a different error message, loading from the eMMC appears to get a bit further:

Quoted 5 lines

U-Boot SPL 2023.10-00054-gef68159087 (Oct 12 2023 - 12:14:22 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 0 (ret = -5)

Quoted 8 lines

mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

So this is pointing to an issue reading from the MMC...

I found https://lists.denx.de/pipermail/u-boot/2023-April/514315.html (which is applied to your branch) and added the following to defconfig:

CONFIG_MMC_SDHCI_SDMA=y
+# CONFIG_SPL_MMC_SDHCI_SDMA is not set

but this seemed to make the loading less reliable:

Quoted 12 lines

U-Boot SPL 2023.10-00054-gef68159087-dirty (Oct 12 2023 - 12:23:10 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
mmc fail to send stop cmd
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

...

Quoted 13 lines
Quoted 13 lines

What happens if you write u-boot-rockchip.bin to eMMC module usinga USB adapter:

  dd if=u-boot-rockchip.bin of=/dev/<device> bs=32k seek=1 conv=fsync

or using U-Boot cmd when booted from a SD-card?

  # Read u-boot-rockchip.bin from first partition of a SD card load mmc 1:1 10000000 u-boot-rockchip.bin

  # Change to eMMC
  mmc dev 0

Quoted 6 lines
Quoted 4 lines

  # Write 10 MiB (0x5000 blocks) at sector 64 (0x40) mmc write $fileaddr 40 5000

Does that make any difference?

I don't think I have an eMMC writer for Pine64 eMMCs, I will try to get hold of one this week.

I have two USB writers. Anyway, the first boot, it fails with:

Quoted 6 lines

U-Boot SPL 2023.10-00054-gef68159087 (Oct 12 2023 - 12:30:14 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
## Checking hash(es) for Image u-boot ... sha256+ OK <hang>

Then again after a reset:

Quoted 93 lines

U-Boot SPL 2023.10-00054-gef68159087 (Oct 12 2023 - 12:30:14 +0100) Trying to boot from MMC1
mmc fail to send stop cmd
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

But it fails to write to the eMMC with:

Quoted 21 lines

=> load mmc 1:2 10000000 u-boot-rockchip.bin
9510400 bytes read in 791 ms (11.5 MiB/s)

=> mmc dev 0
switch to partitions #0, OK
mmc0(part 0) is current device

=> mmc write $fileaddr 40 5000
MMC write: dev # 0, block # 64, count 20480 ... mmc write failed 0 blocks written: ERROR

=> mmc info
Device: mmc@fe310000
Manufacturer ID: 45
OEM: 0
Name: DF4016
Bus Speed: 52000000
Mode: MMC DDR52 (52MHz)
Rd Block Len: 512
MMC version 5.1

Quoted 8 lines

High Capacity: Yes
Capacity: 14.7 GiB
Bus Width: 8-bit DDR
Erase Group Size: 512 KiB
HC WP Group Size: 8 MiB
User Capacity: 14.7 GiB WRREL
Boot Capacity: 4 MiB ENH
RPMB Capacity: 4 MiB ENH

I think this points to some issue with the mmc driver in U-Boot, or possibly some issue with my board. But I find that hard to believe because the Rockchip usbloader seems to write to the eMMC just fine ?

Quoted 37 lines
Quoted 4 lines

Boot log (v2023.10-rc2):

Quoted 8 lines

U-Boot SPL 2023.10-rc2 (Aug 08 2023 - 14:02:34 +0100) rockchip_sdhci_probe clk set rate fail! Trying to boot from MMC1
spl: mmc init failed with error: -110
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1

Strange that second try of eMMC (MMC1) gets little bit longer.

Quoted 10 lines

## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 0 (ret = -5)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Boot log (your branch):

Quoted 11 lines

U-Boot SPL 2023.10-rc1-00368-g16cb31d427 (Aug 08 2023 - 15:17:35 +0100) Trying to boot from MMC1
spl: mmc init failed with error: -70
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Quoted 5 lines

I have not been able to reproduce this kind of issue on any of my two Quartz64-A boards, tested with different eMMC modules.

Does your eMMC module have some compatibility issue?
Do you have any more details on the eMMC module you have tested with?

Quoted 6 lines

I have two eMMCs, one from FORESEE which came with a Pine64 and one marked SanDisk (which I posted the mmc info for above).

My hardware is marked Quartz64-RK3399-V2.0 2021-04-27 Maybe there is some difference with your board?

I will also try an image with vendor u-boot as a next step.

I tried latest Armbian (which seems to use ) from https://github.com/armbian/build/releases/ and flashed the eMMC with the USB writer. It ended up booting to Linux, which proves that the hardware I have is most likey in a good working order ;-)!

Quoted 84 lines

U-Boot SPL 2022.10-rc4-armbian (Feb 11 2023 - 22:25:16 +0000)
saradc@fe720000: Can't update Vdd. Error: -38saradc@fe720000: Can't update Vss. Error: -38can't get vref-supply: -38
rockchip_dnl_key_pressed: adc_channel_single_shot fail!
Trying to boot from MMC2

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-152-g4e725b15f:cl
NOTICE:  BL31: Built : 10:51:13, Jul 15 2021
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    pmu v1 is valid
INFO:    dfs DDR fsp_param[0].freq_mhz= 1560MHz
INFO:    dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO:    dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO:    dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0xa00000
INFO:    SPSR = 0x3c9

U-Boot 2022.10-rc4-armbian (Feb 11 2023 - 22:25:16 +0000)

Model: Pine64 RK3566 Quartz64-A Board
DRAM:  2 GiB
PMIC:  RK8170 (on=0x10, off=0x00)
Core:  266 devices, 21 uclasses, devicetree: separate
MMC:   mmc@fe2b0000: 1, mmc@fe310000: 0
Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: Pine64 RK3566 Quartz64-A Board
can't get vref-supply: -2
rockchip_dnl_key_pressed: adc_channel_single_shot fail!
Net:   No ethernet found.
Hit any key to stop autoboot:  0 

starting USB...
Bus usb@fcc00000: Port not available.
Bus usb@fd000000: Port not available.
Bus usb@fd800000: USB EHCI 1.00
Bus usb@fd840000: USB OHCI 1.0
Bus usb@fd880000: USB EHCI 1.00
Bus usb@fd8c0000: USB OHCI 1.0
scanning bus usb@fd800000 for devices... 1 USB Device(s) found
scanning bus usb@fd840000 for devices... ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did
not provide a handshake (OUT) (5)
unable to get device descriptor (error=-1)
1 USB Device(s) found
scanning bus usb@fd880000 for devices... 1 USB Device(s) found
scanning bus usb@fd8c0000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
1: Armbian
Retrieving file: /boot/uInitrd
Retrieving file: /boot/Image
append: root=UUID=7f9c9970-93ba-46ca-9f03-f3241712ead8 console=ttyS02,1500000 console=tty0 rw no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 splash plymouth.ignore- serial-consoles
Retrieving file: /boot/dtb/rockchip/rk3566-quartz64-a.dtb
Moving Image from 0x2080000 to 0x2200000, end=3de0000
## Loading init Ramdisk from Legacy Image at 0a200000 ...

   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    34402446 Bytes = 32.8 MiB

Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 0a100000
Booting using the fdt blob at 0xa100000
Loading Ramdisk to 7be16000, end 7dee508e ... OK
Loading Device Tree to 000000007bdf7000, end 000000007be158e2 ... OK

Quoted 9 lines

Starting kernel ...

efi_free_pool: illegal free 0x000000007cee7040
efi_free_pool: illegal free 0x000000007cee4040

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[    0.000000] Linux version 6.2.0-rc6-media (root@d00a59921686) (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the
A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321) #trunk.0252 SMP PREEMPT_DYNAMIC Sat Feb 11 22:41:21 UTC 2023
[    0.000000] Machine model: Pine64 RK3566 Quartz64-A Board

Thanks!

Chris

#7 lore raw

Re: [PATCH 1/5] board: rockchip: Add Pine64 Quartz64-A Board

Hi Christopher,

Quoted 147 lines · Christopher Obbard

Hi Jonas,

Quoted 123 lines · Christopher Obbard

Hi Jonas,

Sorry for the late response, I've been meaning to test this for a while but not got around to it.

Quoted 51 lines · Jonas Karlman

Hi Christopher,

Quoted 48 lines · Christopher Obbard

Hi Jonas,

Quoted 43 lines · Jonas Karlman
Quoted 11 lines · Jonas Karlman

The Pine64 Quartz64 Model A is a single-board computer based on the Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0, CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a 20 pin GPIO header.

Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Quoted 6 lines

Device tree is imported from linux v6.4.

---

[...]

Boot log with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf:

[...]

U-Boot 2023.07 (Jul 23 2023 - 12:42:18 +0000)

Model: Pine64 RK3566 Quartz64-A Board
DRAM:  8 GiB (effective 7.7 GiB)
PMIC:  RK8170 (on=0x10, off=0x00)
Core:  321 devices, 27 uclasses, devicetree: separate MMC:   rockchip_sdhci_probe clk set rate fail! mmc@fe2b0000: 1, mmc@fe2c0000: 2, mmc@fe310000: 0 Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: Pine64 RK3566 Quartz64-A Board
Net:   No ethernet found.

Hit any key to stop autoboot:  0
=>

Quoted 5 lines
Quoted 2 lines

I just tried booting U-Boot v2023.10-rc2 with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf, on my Quartz64-A but it fails during loading of some parts. I removed the output of the RK TPL from my logs as there were no errors.

Try with latest rk3566_ddr_1056MHz_v1.18.bin and see if that makes any difference.

No difference.

I've also checked, there is no other maskrom bootable media such as SPI flash connected to the board.

Quoted 4 lines
Quoted 2 lines

This is when booting from eMMC.

Does it boot with SD-card or other eMMC modules?

Booting from SD card (without eMMC connected), everything works fine.

Quoted 7 lines
Quoted 3 lines

I also tried building your branch from https://github.com/Kwiboo/u-boot-rockchip/tree/rk3568-2023.10

Please try with a GitHub actions built u-boot-rockchip.bin based on my rk3568-2023.07.02 branch at
https://github.com/Kwiboo/u-boot-build/actions/runs/5777761235

With that exact artifact, flashed with:

Quoted 4 lines

rkdeveloptool db rk356x_spl_loader_v1.18.113.bin
rkdeveloptool ef
rkdeveloptool wl 64 u-boot-rockchip.bin
rkdeveloptool rd

it fails to boot with with:

Quoted 21 lines

DDR V1.18 f366f69a7d typ 23/07/17-15:48:58
ln
LP4/4x derate en, other dram:1x trefi
SRX
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=8 Size=8192MB

change to: 324MHz
clk skew:0x60

change to: 528MHz
clk skew:0x58

change to: 780MHz
clk skew:0x58

change to: 1056MHz(final freq)
clk skew:0x32
out

Quoted 11 lines

U-Boot SPL 2023.07.02-g09919887 (Aug 06 2023 - 16:59:31 +0000) Trying to boot from MMC1
spl: mmc init failed with error: -70
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc fail to send stop cmd
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Quoted 1 line

I also tried a second eMMC, but it also failed to boot with the same "mmc block read error" message.

I tried with your latest branch https://github.com/Kwiboo/u-boot-rockchip/commits/rk3568-2023.10

and this time a different error message, loading from the eMMC appears to get a bit further:

Quoted 5 lines

U-Boot SPL 2023.10-00054-gef68159087 (Oct 12 2023 - 12:14:22 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 0 (ret = -5)

Quoted 8 lines

mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Quoted 23 lines

So this is pointing to an issue reading from the MMC...

I found https://lists.denx.de/pipermail/u-boot/2023-April/514315.html (which is applied to your branch) and added the following to defconfig:

CONFIG_MMC_SDHCI_SDMA=y
+# CONFIG_SPL_MMC_SDHCI_SDMA is not set

but this seemed to make the loading less reliable:

Quoted 12 lines

U-Boot SPL 2023.10-00054-gef68159087-dirty (Oct 12 2023 - 12:23:10 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
mmc fail to send stop cmd
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Thanks for testing different combinations.

I did find an issue with emmc write using ddr52 and hs400 modes on rk3568. On rk3588 emmc write only worked reliable after hs200 mode had been used.

Please try the changes from following commit, or my rk35xx-2024.01 work-in-progress branch:

WIP: rockchip: rk35xx: improve emmc write
https://github.com/Kwiboo/u-boot-rockchip/commit/aa6156179bb2034e8ba26753e05285e276327d78

Most rk356x boards currently default to ddr52 mode, and possible emmc read is also affected with similar issue as emmc write.

I have also discovered a strange issue on an Amlogic soc related to U-Boot mmc commands and gcc optimization, please see following patch:
https://patchwork.ozlabs.org/patch/1839392/

Please try with CONFIG_MMC_TRACE=y to see what commands fails on your device.

If above patches does not work also try with following options applied:

CONFIG_MMC_HS200_SUPPORT=y
CONFIG_SPL_MMC_HS200_SUPPORT=y

Use of HS200 seem to be the most reliable option on rk35xx based on my limited testing.

Quoted 32 lines

...

Quoted 13 lines
Quoted 13 lines

What happens if you write u-boot-rockchip.bin to eMMC module usinga USB adapter:

  dd if=u-boot-rockchip.bin of=/dev/<device> bs=32k seek=1 conv=fsync

or using U-Boot cmd when booted from a SD-card?

  # Read u-boot-rockchip.bin from first partition of a SD card load mmc 1:1 10000000 u-boot-rockchip.bin

  # Change to eMMC
  mmc dev 0

Quoted 6 lines
Quoted 4 lines

  # Write 10 MiB (0x5000 blocks) at sector 64 (0x40) mmc write $fileaddr 40 5000

Does that make any difference?

I don't think I have an eMMC writer for Pine64 eMMCs, I will try to get hold of one this week.

I have two USB writers. Anyway, the first boot, it fails with:

Quoted 6 lines

U-Boot SPL 2023.10-00054-gef68159087 (Oct 12 2023 - 12:30:14 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
## Checking hash(es) for Image u-boot ... sha256+ OK <hang>

Quoted 51 lines

Then again after a reset:

Quoted 49 lines

U-Boot SPL 2023.10-00054-gef68159087 (Oct 12 2023 - 12:30:14 +0100) Trying to boot from MMC1
mmc fail to send stop cmd
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

But it fails to write to the eMMC with:

Quoted 21 lines

=> load mmc 1:2 10000000 u-boot-rockchip.bin
9510400 bytes read in 791 ms (11.5 MiB/s)

=> mmc dev 0
switch to partitions #0, OK
mmc0(part 0) is current device

=> mmc write $fileaddr 40 5000
MMC write: dev # 0, block # 64, count 20480 ... mmc write failed 0 blocks written: ERROR

=> mmc info
Device: mmc@fe310000
Manufacturer ID: 45
OEM: 0
Name: DF4016
Bus Speed: 52000000
Mode: MMC DDR52 (52MHz)
Rd Block Len: 512
MMC version 5.1

Quoted 8 lines

High Capacity: Yes
Capacity: 14.7 GiB
Bus Width: 8-bit DDR
Erase Group Size: 512 KiB
HC WP Group Size: 8 MiB
User Capacity: 14.7 GiB WRREL
Boot Capacity: 4 MiB ENH
RPMB Capacity: 4 MiB ENH

I think this points to some issue with the mmc driver in U-Boot, or possibly some issue with my board. But I find that hard to believe because the Rockchip usbloader seems to write to the eMMC just fine ?

Probably related to sdhci driver and rx/tx tap and/or delay num etc.

Quoted 38 lines
Quoted 38 lines
Quoted 38 lines
Quoted 5 lines

Boot log (v2023.10-rc2):

Quoted 8 lines

U-Boot SPL 2023.10-rc2 (Aug 08 2023 - 14:02:34 +0100) rockchip_sdhci_probe clk set rate fail! Trying to boot from MMC1
spl: mmc init failed with error: -110
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1

Strange that second try of eMMC (MMC1) gets little bit longer.

Quoted 21 lines

## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 0 (ret = -5)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Boot log (your branch):

U-Boot SPL 2023.10-rc1-00368-g16cb31d427 (Aug 08 2023 - 15:17:35 +0100) Trying to boot from MMC1
spl: mmc init failed with error: -70
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Quoted 7 lines
Quoted 7 lines
Quoted 5 lines

I have not been able to reproduce this kind of issue on any of my two Quartz64-A boards, tested with different eMMC modules.

Does your eMMC module have some compatibility issue?
Do you have any more details on the eMMC module you have tested with?

I have two eMMCs, one from FORESEE which came with a Pine64 and one marked SanDisk (which I posted the mmc info for above).

My eMMC modules is also FORESEE or SanDisk, from Pine64, Radxa and Hardkernel.

Quoted 3 lines
Quoted 3 lines

My hardware is marked Quartz64-RK3399-V2.0 2021-04-27 Maybe there is some difference with your board?

Should match my board, I have the hw revision where SATA port is removed. (boards with/without SATA have same version silk on the board)

Quoted 5 lines
Quoted 2 lines

I will also try an image with vendor u-boot as a next step.

I tried latest Armbian (which seems to use ) from https://github.com/armbian/build/releases/ and flashed the eMMC with the USB writer. It ended up booting to Linux, which proves that the hardware I have is most likey in a good working order ;-)!

Hopefully the issue is related to the peephole2 optimization issue or the use of a not fully supported ddr52 mode.

Regards,
Jonas

Quoted 102 lines
Quoted 86 lines

U-Boot SPL 2022.10-rc4-armbian (Feb 11 2023 - 22:25:16 +0000)
saradc@fe720000: Can't update Vdd. Error: -38saradc@fe720000: Can't update Vss. Error: -38can't get vref-supply: -38
rockchip_dnl_key_pressed: adc_channel_single_shot fail!
Trying to boot from MMC2

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-152-g4e725b15f:cl
NOTICE:  BL31: Built : 10:51:13, Jul 15 2021
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    pmu v1 is valid
INFO:    dfs DDR fsp_param[0].freq_mhz= 1560MHz
INFO:    dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO:    dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO:    dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0xa00000
INFO:    SPSR = 0x3c9

U-Boot 2022.10-rc4-armbian (Feb 11 2023 - 22:25:16 +0000)

Model: Pine64 RK3566 Quartz64-A Board
DRAM:  2 GiB
PMIC:  RK8170 (on=0x10, off=0x00)
Core:  266 devices, 21 uclasses, devicetree: separate
MMC:   mmc@fe2b0000: 1, mmc@fe310000: 0
Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: Pine64 RK3566 Quartz64-A Board
can't get vref-supply: -2
rockchip_dnl_key_pressed: adc_channel_single_shot fail!
Net:   No ethernet found.
Hit any key to stop autoboot:  0 

starting USB...
Bus usb@fcc00000: Port not available.
Bus usb@fd000000: Port not available.
Bus usb@fd800000: USB EHCI 1.00
Bus usb@fd840000: USB OHCI 1.0
Bus usb@fd880000: USB EHCI 1.00
Bus usb@fd8c0000: USB OHCI 1.0
scanning bus usb@fd800000 for devices... 1 USB Device(s) found
scanning bus usb@fd840000 for devices... ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did
not provide a handshake (OUT) (5)
unable to get device descriptor (error=-1)
1 USB Device(s) found
scanning bus usb@fd880000 for devices... 1 USB Device(s) found
scanning bus usb@fd8c0000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
1: Armbian
Retrieving file: /boot/uInitrd
Retrieving file: /boot/Image
append: root=UUID=7f9c9970-93ba-46ca-9f03-f3241712ead8 console=ttyS02,1500000 console=tty0 rw no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 splash plymouth.ignore- serial-consoles
Retrieving file: /boot/dtb/rockchip/rk3566-quartz64-a.dtb
Moving Image from 0x2080000 to 0x2200000, end=3de0000
## Loading init Ramdisk from Legacy Image at 0a200000 ...

   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    34402446 Bytes = 32.8 MiB

Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 0a100000
Booting using the fdt blob at 0xa100000
Loading Ramdisk to 7be16000, end 7dee508e ... OK
Loading Device Tree to 000000007bdf7000, end 000000007be158e2 ... OK

Quoted 9 lines

Starting kernel ...

efi_free_pool: illegal free 0x000000007cee7040
efi_free_pool: illegal free 0x000000007cee4040

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[    0.000000] Linux version 6.2.0-rc6-media (root@d00a59921686) (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the
A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321) #trunk.0252 SMP PREEMPT_DYNAMIC Sat Feb 11 22:41:21 UTC 2023
[    0.000000] Machine model: Pine64 RK3566 Quartz64-A Board

Thanks!

Chris

#8 lore raw

Re: [PATCH 1/5] board: rockchip: Add Pine64 Quartz64-A Board

Quoted 186 lines · Jonas Karlman

Hi Christopher,

Quoted 147 lines · Christopher Obbard

Hi Jonas,

Quoted 123 lines · Christopher Obbard

Hi Jonas,

Sorry for the late response, I've been meaning to test this for a while but not got around to it.

Quoted 51 lines · Jonas Karlman

Hi Christopher,

Quoted 48 lines · Christopher Obbard

Hi Jonas,

Quoted 43 lines · Jonas Karlman
Quoted 11 lines · Jonas Karlman

The Pine64 Quartz64 Model A is a single-board computer based on the Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0, CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a 20 pin GPIO header.

Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Quoted 6 lines

Device tree is imported from linux v6.4.

---

[...]

Boot log with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf:

[...]

U-Boot 2023.07 (Jul 23 2023 - 12:42:18 +0000)

Model: Pine64 RK3566 Quartz64-A Board
DRAM:  8 GiB (effective 7.7 GiB)
PMIC:  RK8170 (on=0x10, off=0x00)
Core:  321 devices, 27 uclasses, devicetree: separate MMC:   rockchip_sdhci_probe clk set rate fail! mmc@fe2b0000: 1, mmc@fe2c0000: 2, mmc@fe310000: 0 Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: Pine64 RK3566 Quartz64-A Board
Net:   No ethernet found.

Hit any key to stop autoboot:  0
=>

Quoted 5 lines
Quoted 2 lines

I just tried booting U-Boot v2023.10-rc2 with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf, on my Quartz64-A but it fails during loading of some parts. I removed the output of the RK TPL from my logs as there were no errors.

Try with latest rk3566_ddr_1056MHz_v1.18.bin and see if that makes any difference.

No difference.

I've also checked, there is no other maskrom bootable media such as SPI flash connected to the board.

Quoted 4 lines
Quoted 2 lines

This is when booting from eMMC.

Does it boot with SD-card or other eMMC modules?

Booting from SD card (without eMMC connected), everything works fine.

Quoted 7 lines
Quoted 3 lines

I also tried building your branch from https://github.com/Kwiboo/u-boot-rockchip/tree/rk3568-2023.10

Please try with a GitHub actions built u-boot-rockchip.bin based on my rk3568-2023.07.02 branch at
https://github.com/Kwiboo/u-boot-build/actions/runs/5777761235

With that exact artifact, flashed with:

Quoted 4 lines

rkdeveloptool db rk356x_spl_loader_v1.18.113.bin
rkdeveloptool ef
rkdeveloptool wl 64 u-boot-rockchip.bin
rkdeveloptool rd

it fails to boot with with:

Quoted 21 lines

DDR V1.18 f366f69a7d typ 23/07/17-15:48:58
ln
LP4/4x derate en, other dram:1x trefi
SRX
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=8 Size=8192MB

change to: 324MHz
clk skew:0x60

change to: 528MHz
clk skew:0x58

change to: 780MHz
clk skew:0x58

change to: 1056MHz(final freq)
clk skew:0x32
out

Quoted 11 lines

U-Boot SPL 2023.07.02-g09919887 (Aug 06 2023 - 16:59:31 +0000) Trying to boot from MMC1
spl: mmc init failed with error: -70
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc fail to send stop cmd
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Quoted 1 line

I also tried a second eMMC, but it also failed to boot with the same "mmc block read error" message.

I tried with your latest branch https://github.com/Kwiboo/u-boot-rockchip/commits/rk3568-2023.10

and this time a different error message, loading from the eMMC appears to get a bit further:

Quoted 5 lines

U-Boot SPL 2023.10-00054-gef68159087 (Oct 12 2023 - 12:14:22 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 0 (ret = -5)

Quoted 8 lines

mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Quoted 23 lines

So this is pointing to an issue reading from the MMC...

I found https://lists.denx.de/pipermail/u-boot/2023-April/514315.html (which is applied to your branch) and added the following to defconfig:

CONFIG_MMC_SDHCI_SDMA=y
+# CONFIG_SPL_MMC_SDHCI_SDMA is not set

but this seemed to make the loading less reliable:

Quoted 12 lines

U-Boot SPL 2023.10-00054-gef68159087-dirty (Oct 12 2023 - 12:23:10 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
mmc fail to send stop cmd
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Thanks for testing different combinations.

I did find an issue with emmc write using ddr52 and hs400 modes on rk3568. On rk3588 emmc write only worked reliable after hs200 mode had been used.

Please try the changes from following commit, or my rk35xx-2024.01 work-in-progress branch:

WIP: rockchip: rk35xx: improve emmc write
https://github.com/Kwiboo/u-boot-rockchip/commit/aa6156179bb2034e8ba26753e05285e276327d78

Quoted 6 lines

Most rk356x boards currently default to ddr52 mode, and possible emmc read is also affected with similar issue as emmc write.

I have also discovered a strange issue on an Amlogic soc related to U-Boot mmc commands and gcc optimization, please see following patch:
https://patchwork.ozlabs.org/patch/1839392/

Posted link to wrong patch, I meant the following patch:

[RFC] mmc: Remove alignment hole for cmdidx in struct mmc_cmd
https://patchwork.ozlabs.org/patch/1841495/

Regards,
Jonas

Quoted 268 lines

Please try with CONFIG_MMC_TRACE=y to see what commands fails on your device.

If above patches does not work also try with following options applied:

CONFIG_MMC_HS200_SUPPORT=y
CONFIG_SPL_MMC_HS200_SUPPORT=y

Use of HS200 seem to be the most reliable option on rk35xx based on my limited testing.

Quoted 32 lines

...

Quoted 13 lines
Quoted 13 lines

What happens if you write u-boot-rockchip.bin to eMMC module usinga USB adapter:

  dd if=u-boot-rockchip.bin of=/dev/<device> bs=32k seek=1 conv=fsync

or using U-Boot cmd when booted from a SD-card?

  # Read u-boot-rockchip.bin from first partition of a SD card load mmc 1:1 10000000 u-boot-rockchip.bin

  # Change to eMMC
  mmc dev 0

Quoted 6 lines
Quoted 4 lines

  # Write 10 MiB (0x5000 blocks) at sector 64 (0x40) mmc write $fileaddr 40 5000

Does that make any difference?

I don't think I have an eMMC writer for Pine64 eMMCs, I will try to get hold of one this week.

I have two USB writers. Anyway, the first boot, it fails with:

Quoted 6 lines

U-Boot SPL 2023.10-00054-gef68159087 (Oct 12 2023 - 12:30:14 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
## Checking hash(es) for Image u-boot ... sha256+ OK <hang>

Quoted 51 lines

Then again after a reset:

Quoted 49 lines

U-Boot SPL 2023.10-00054-gef68159087 (Oct 12 2023 - 12:30:14 +0100) Trying to boot from MMC1
mmc fail to send stop cmd
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

But it fails to write to the eMMC with:

Quoted 21 lines

=> load mmc 1:2 10000000 u-boot-rockchip.bin
9510400 bytes read in 791 ms (11.5 MiB/s)

=> mmc dev 0
switch to partitions #0, OK
mmc0(part 0) is current device

=> mmc write $fileaddr 40 5000
MMC write: dev # 0, block # 64, count 20480 ... mmc write failed 0 blocks written: ERROR

=> mmc info
Device: mmc@fe310000
Manufacturer ID: 45
OEM: 0
Name: DF4016
Bus Speed: 52000000
Mode: MMC DDR52 (52MHz)
Rd Block Len: 512
MMC version 5.1

Quoted 8 lines

High Capacity: Yes
Capacity: 14.7 GiB
Bus Width: 8-bit DDR
Erase Group Size: 512 KiB
HC WP Group Size: 8 MiB
User Capacity: 14.7 GiB WRREL
Boot Capacity: 4 MiB ENH
RPMB Capacity: 4 MiB ENH

I think this points to some issue with the mmc driver in U-Boot, or possibly some issue with my board. But I find that hard to believe because the Rockchip usbloader seems to write to the eMMC just fine ?

Probably related to sdhci driver and rx/tx tap and/or delay num etc.

Quoted 38 lines
Quoted 38 lines
Quoted 38 lines
Quoted 5 lines

Boot log (v2023.10-rc2):

Quoted 8 lines

U-Boot SPL 2023.10-rc2 (Aug 08 2023 - 14:02:34 +0100) rockchip_sdhci_probe clk set rate fail! Trying to boot from MMC1
spl: mmc init failed with error: -110
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1

Strange that second try of eMMC (MMC1) gets little bit longer.

Quoted 21 lines

## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 0 (ret = -5)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Boot log (your branch):

U-Boot SPL 2023.10-rc1-00368-g16cb31d427 (Aug 08 2023 - 15:17:35 +0100) Trying to boot from MMC1
spl: mmc init failed with error: -70
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Quoted 7 lines
Quoted 7 lines
Quoted 5 lines

I have not been able to reproduce this kind of issue on any of my two Quartz64-A boards, tested with different eMMC modules.

Does your eMMC module have some compatibility issue?
Do you have any more details on the eMMC module you have tested with?

I have two eMMCs, one from FORESEE which came with a Pine64 and one marked SanDisk (which I posted the mmc info for above).

My eMMC modules is also FORESEE or SanDisk, from Pine64, Radxa and Hardkernel.

Quoted 3 lines
Quoted 3 lines

My hardware is marked Quartz64-RK3399-V2.0 2021-04-27 Maybe there is some difference with your board?

Should match my board, I have the hw revision where SATA port is removed. (boards with/without SATA have same version silk on the board)

Quoted 5 lines
Quoted 2 lines

I will also try an image with vendor u-boot as a next step.

I tried latest Armbian (which seems to use ) from https://github.com/armbian/build/releases/ and flashed the eMMC with the USB writer. It ended up booting to Linux, which proves that the hardware I have is most likey in a good working order ;-)!

Hopefully the issue is related to the peephole2 optimization issue or the use of a not fully supported ddr52 mode.

Regards,
Jonas

Quoted 102 lines
Quoted 86 lines

U-Boot SPL 2022.10-rc4-armbian (Feb 11 2023 - 22:25:16 +0000)
saradc@fe720000: Can't update Vdd. Error: -38saradc@fe720000: Can't update Vss. Error: -38can't get vref-supply: -38
rockchip_dnl_key_pressed: adc_channel_single_shot fail!
Trying to boot from MMC2

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-152-g4e725b15f:cl
NOTICE:  BL31: Built : 10:51:13, Jul 15 2021
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    pmu v1 is valid
INFO:    dfs DDR fsp_param[0].freq_mhz= 1560MHz
INFO:    dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO:    dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO:    dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0xa00000
INFO:    SPSR = 0x3c9

U-Boot 2022.10-rc4-armbian (Feb 11 2023 - 22:25:16 +0000)

Model: Pine64 RK3566 Quartz64-A Board
DRAM:  2 GiB
PMIC:  RK8170 (on=0x10, off=0x00)
Core:  266 devices, 21 uclasses, devicetree: separate
MMC:   mmc@fe2b0000: 1, mmc@fe310000: 0
Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: Pine64 RK3566 Quartz64-A Board
can't get vref-supply: -2
rockchip_dnl_key_pressed: adc_channel_single_shot fail!
Net:   No ethernet found.
Hit any key to stop autoboot:  0 

starting USB...
Bus usb@fcc00000: Port not available.
Bus usb@fd000000: Port not available.
Bus usb@fd800000: USB EHCI 1.00
Bus usb@fd840000: USB OHCI 1.0
Bus usb@fd880000: USB EHCI 1.00
Bus usb@fd8c0000: USB OHCI 1.0
scanning bus usb@fd800000 for devices... 1 USB Device(s) found
scanning bus usb@fd840000 for devices... ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did
not provide a handshake (OUT) (5)
unable to get device descriptor (error=-1)
1 USB Device(s) found
scanning bus usb@fd880000 for devices... 1 USB Device(s) found
scanning bus usb@fd8c0000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
1: Armbian
Retrieving file: /boot/uInitrd
Retrieving file: /boot/Image
append: root=UUID=7f9c9970-93ba-46ca-9f03-f3241712ead8 console=ttyS02,1500000 console=tty0 rw no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 splash plymouth.ignore- serial-consoles
Retrieving file: /boot/dtb/rockchip/rk3566-quartz64-a.dtb
Moving Image from 0x2080000 to 0x2200000, end=3de0000
## Loading init Ramdisk from Legacy Image at 0a200000 ...

   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    34402446 Bytes = 32.8 MiB

Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 0a100000
Booting using the fdt blob at 0xa100000
Loading Ramdisk to 7be16000, end 7dee508e ... OK
Loading Device Tree to 000000007bdf7000, end 000000007be158e2 ... OK

Quoted 9 lines

Starting kernel ...

efi_free_pool: illegal free 0x000000007cee7040
efi_free_pool: illegal free 0x000000007cee4040

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[    0.000000] Linux version 6.2.0-rc6-media (root@d00a59921686) (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the
A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321) #trunk.0252 SMP PREEMPT_DYNAMIC Sat Feb 11 22:41:21 UTC 2023
[    0.000000] Machine model: Pine64 RK3566 Quartz64-A Board

Thanks!

Chris

#9 lore raw

Re: [PATCH 1/5] board: rockchip: Add Pine64 Quartz64-A Board

Hi Jonas,

Quoted 190 lines · Jonas Karlman
Quoted 189 lines · Jonas Karlman

Hi Christopher,

Quoted 147 lines · Christopher Obbard

Hi Jonas,

Quoted 123 lines · Christopher Obbard

Hi Jonas,

Sorry for the late response, I've been meaning to test this for a while but not got around to it.

Quoted 51 lines · Jonas Karlman

Hi Christopher,

Quoted 48 lines · Christopher Obbard

Hi Jonas,

Quoted 43 lines · Jonas Karlman
Quoted 11 lines · Jonas Karlman

The Pine64 Quartz64 Model A is a single-board computer based on the Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0, CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a 20 pin GPIO header.

Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Quoted 6 lines

Device tree is imported from linux v6.4.

---

[...]

Boot log with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf:

[...]

U-Boot 2023.07 (Jul 23 2023 - 12:42:18 +0000)

Model: Pine64 RK3566 Quartz64-A Board
DRAM:  8 GiB (effective 7.7 GiB)
PMIC:  RK8170 (on=0x10, off=0x00)
Core:  321 devices, 27 uclasses, devicetree: separate MMC:   rockchip_sdhci_probe clk set rate fail! mmc@fe2b0000: 1, mmc@fe2c0000: 2, mmc@fe310000: 0 Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: Pine64 RK3566 Quartz64-A Board
Net:   No ethernet found.

Hit any key to stop autoboot:  0
=>

Quoted 5 lines
Quoted 2 lines

I just tried booting U-Boot v2023.10-rc2 with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf, on my Quartz64-A but it fails during loading of some parts. I removed the output of the RK TPL from my logs as there were no errors.

Try with latest rk3566_ddr_1056MHz_v1.18.bin and see if that makes any difference.

No difference.

I've also checked, there is no other maskrom bootable media such as SPI flash connected to the board.

Quoted 4 lines
Quoted 2 lines

This is when booting from eMMC.

Does it boot with SD-card or other eMMC modules?

Booting from SD card (without eMMC connected), everything works fine.

Quoted 7 lines
Quoted 3 lines

I also tried building your branch from https://github.com/Kwiboo/u-boot-rockchip/tree/rk3568-2023.10

Please try with a GitHub actions built u-boot-rockchip.bin based on my rk3568-2023.07.02 branch at
https://github.com/Kwiboo/u-boot-build/actions/runs/5777761235

With that exact artifact, flashed with:

Quoted 4 lines

rkdeveloptool db rk356x_spl_loader_v1.18.113.bin
rkdeveloptool ef
rkdeveloptool wl 64 u-boot-rockchip.bin
rkdeveloptool rd

it fails to boot with with:

Quoted 21 lines

DDR V1.18 f366f69a7d typ 23/07/17-15:48:58
ln
LP4/4x derate en, other dram:1x trefi
SRX
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=8 Size=8192MB

change to: 324MHz
clk skew:0x60

change to: 528MHz
clk skew:0x58

change to: 780MHz
clk skew:0x58

change to: 1056MHz(final freq)
clk skew:0x32
out

Quoted 11 lines

U-Boot SPL 2023.07.02-g09919887 (Aug 06 2023 - 16:59:31 +0000) Trying to boot from MMC1
spl: mmc init failed with error: -70
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc fail to send stop cmd
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Quoted 1 line

I also tried a second eMMC, but it also failed to boot with the same "mmc block read error" message.

I tried with your latest branch https://github.com/Kwiboo/u-boot-rockchip/commits/rk3568-2023.10

and this time a different error message, loading from the eMMC appears to get a bit further:

Quoted 5 lines

U-Boot SPL 2023.10-00054-gef68159087 (Oct 12 2023 - 12:14:22 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 0 (ret = -5)

Quoted 8 lines

mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Quoted 23 lines

So this is pointing to an issue reading from the MMC...

I found https://lists.denx.de/pipermail/u-boot/2023-April/514315.html (which is applied to your branch) and added the following to defconfig:

CONFIG_MMC_SDHCI_SDMA=y
+# CONFIG_SPL_MMC_SDHCI_SDMA is not set

but this seemed to make the loading less reliable:

Quoted 12 lines

U-Boot SPL 2023.10-00054-gef68159087-dirty (Oct 12 2023 - 12:23:10 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
mmc fail to send stop cmd
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Thanks for testing different combinations.

I did find an issue with emmc write using ddr52 and hs400 modes on rk3568. On rk3588 emmc write only worked reliable after hs200 mode had been used.

Please try the changes from following commit, or my rk35xx-2024.01 work-in-progress branch:

WIP: rockchip: rk35xx: improve emmc write
https://github.com/Kwiboo/u-boot-rockchip/commit/aa6156179bb2034e8ba26753e05285e276327d78

Most rk356x boards currently default to ddr52 mode, and possible emmc read is also affected with similar issue as emmc write.

Quoted 8 lines
Quoted 3 lines

I have also discovered a strange issue on an Amlogic soc related to U-Boot mmc commands and gcc optimization, please see following patch:
https://patchwork.ozlabs.org/patch/1839392/

Posted link to wrong patch, I meant the following patch:

[RFC] mmc: Remove alignment hole for cmdidx in struct mmc_cmd
https://patchwork.ozlabs.org/patch/1841495/

I just tried with your branch & this patch on top, it still fails to boot and seems to be random how far it gets through the loading phase. Again I've removed the ddr training log. It seems to get further this time though...

Boot #1:

Quoted 6 lines

U-Boot SPL 2023.10-00055-g29313fff30 (Oct 17 2023 - 09:44:21 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
## Checking hash(es) for Image u-boot ... sha256+ OK <crash>

Boot #2:

Quoted 10 lines

U-Boot SPL 2023.10-00055-g29313fff30 (Oct 17 2023 - 09:44:21 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
## Checking hash(es) for Image u-boot ... sha256+ OK
## Checking hash(es) for Image fdt-1 ... sha256+ OK
## Checking hash(es) for Image atf-2 ... sha256+ OK
## Checking hash(es) for Image atf-3 ... sha256+ OK
## Checking hash(es) for Image atf-4 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 4 (ret = -5)

Quoted 8 lines

mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Boot #3:

Quoted 10 lines

U-Boot SPL 2023.10-00055-g29313fff30 (Oct 17 2023 - 09:44:21 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
## Checking hash(es) for Image u-boot ... sha256+ OK
## Checking hash(es) for Image fdt-1 ... sha256+ OK
## Checking hash(es) for Image atf-2 ... sha256+ OK
## Checking hash(es) for Image atf-3 ... sha256+ OK
## Checking hash(es) for Image atf-4 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 4 (ret = -5)

Quoted 9 lines

mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

For reference I am using gcc from Debian unstable:

Quoted 2 lines
$ aarch64-linux-gnu-gcc --version
aarch64-linux-gnu-gcc (Debian 13.2.0-2) 13.2.0

I can test with alternative cross-compiler if that would be useful.

Thanks,
Chris

Quoted 277 lines

Regards,
Jonas

Quoted 272 lines

Please try with CONFIG_MMC_TRACE=y to see what commands fails on your device.

If above patches does not work also try with following options applied:

CONFIG_MMC_HS200_SUPPORT=y
CONFIG_SPL_MMC_HS200_SUPPORT=y

Use of HS200 seem to be the most reliable option on rk35xx based on my limited testing.

Quoted 32 lines

...

Quoted 13 lines
Quoted 13 lines

What happens if you write u-boot-rockchip.bin to eMMC module usinga USB adapter:

  dd if=u-boot-rockchip.bin of=/dev/<device> bs=32k seek=1 conv=fsync

or using U-Boot cmd when booted from a SD-card?

  # Read u-boot-rockchip.bin from first partition of a SD card load mmc 1:1 10000000 u-boot-rockchip.bin

  # Change to eMMC
  mmc dev 0

Quoted 6 lines
Quoted 4 lines

  # Write 10 MiB (0x5000 blocks) at sector 64 (0x40) mmc write $fileaddr 40 5000

Does that make any difference?

I don't think I have an eMMC writer for Pine64 eMMCs, I will try to get hold of one this week.

I have two USB writers. Anyway, the first boot, it fails with:

Quoted 6 lines

U-Boot SPL 2023.10-00054-gef68159087 (Oct 12 2023 - 12:30:14 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
## Checking hash(es) for Image u-boot ... sha256+ OK <hang>

Quoted 52 lines

Then again after a reset:

Quoted 50 lines

U-Boot SPL 2023.10-00054-gef68159087 (Oct 12 2023 - 12:30:14 +0100) Trying to boot from MMC1
mmc fail to send stop cmd
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

But it fails to write to the eMMC with:

Quoted 21 lines

=> load mmc 1:2 10000000 u-boot-rockchip.bin
9510400 bytes read in 791 ms (11.5 MiB/s)

=> mmc dev 0
switch to partitions #0, OK
mmc0(part 0) is current device

=> mmc write $fileaddr 40 5000
MMC write: dev # 0, block # 64, count 20480 ... mmc write failed 0 blocks written: ERROR

=> mmc info
Device: mmc@fe310000
Manufacturer ID: 45
OEM: 0
Name: DF4016
Bus Speed: 52000000
Mode: MMC DDR52 (52MHz)
Rd Block Len: 512
MMC version 5.1

Quoted 8 lines

High Capacity: Yes
Capacity: 14.7 GiB
Bus Width: 8-bit DDR
Erase Group Size: 512 KiB
HC WP Group Size: 8 MiB
User Capacity: 14.7 GiB WRREL
Boot Capacity: 4 MiB ENH
RPMB Capacity: 4 MiB ENH

I think this points to some issue with the mmc driver in U-Boot, or possibly some issue with my board. But I find that hard to believe because the Rockchip usbloader seems to write to the eMMC just
fine ?

Probably related to sdhci driver and rx/tx tap and/or delay num etc.

Quoted 38 lines
Quoted 38 lines
Quoted 38 lines
Quoted 5 lines

Boot log (v2023.10-rc2):

Quoted 8 lines

U-Boot SPL 2023.10-rc2 (Aug 08 2023 - 14:02:34 +0100) rockchip_sdhci_probe clk set rate fail! Trying to boot from MMC1
spl: mmc init failed with error: -110
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1

Strange that second try of eMMC (MMC1) gets little bit longer.

Quoted 21 lines

## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 0 (ret = -5)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Boot log (your branch):

U-Boot SPL 2023.10-rc1-00368-g16cb31d427 (Aug 08 2023 - 15:17:35 +0100) Trying to boot from MMC1
spl: mmc init failed with error: -70
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Quoted 7 lines
Quoted 7 lines
Quoted 5 lines

I have not been able to reproduce this kind of issue on any of my two Quartz64-A boards, tested with different eMMC modules.

Does your eMMC module have some compatibility issue?
Do you have any more details on the eMMC module you have tested with?

I have two eMMCs, one from FORESEE which came with a Pine64 and one marked SanDisk (which I posted the mmc info for above).

My eMMC modules is also FORESEE or SanDisk, from Pine64, Radxa and Hardkernel.

Quoted 3 lines
Quoted 3 lines

My hardware is marked Quartz64-RK3399-V2.0 2021-04-27 Maybe there is some difference with your board?

Should match my board, I have the hw revision where SATA port is removed. (boards with/without SATA have same version silk on the board)

Quoted 6 lines
Quoted 2 lines

I will also try an image with vendor u-boot as a next step.

I tried latest Armbian (which seems to use ) from https://github.com/armbian/build/releases/ and flashed the eMMC with the USB writer. It ended up booting to Linux, which proves that the hardware I
have is most likey in a good working order ;-)!

Hopefully the issue is related to the peephole2 optimization issue or the use of a not fully supported ddr52 mode.

Regards,
Jonas

Quoted 104 lines
Quoted 89 lines

U-Boot SPL 2022.10-rc4-armbian (Feb 11 2023 - 22:25:16 +0000)
saradc@fe720000: Can't update Vdd. Error: -38saradc@fe720000: Can't update Vss. Error: -38can't get vref-supply: -38
rockchip_dnl_key_pressed: adc_channel_single_shot fail!
Trying to boot from MMC2
INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-152-g4e725b15f:cl
NOTICE:  BL31: Built : 10:51:13, Jul 15 2021
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    pmu v1 is valid
INFO:    dfs DDR fsp_param[0].freq_mhz= 1560MHz
INFO:    dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO:    dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO:    dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0xa00000
INFO:    SPSR = 0x3c9

U-Boot 2022.10-rc4-armbian (Feb 11 2023 - 22:25:16 +0000)

Model: Pine64 RK3566 Quartz64-A Board
DRAM:  2 GiB
PMIC:  RK8170 (on=0x10, off=0x00)
Core:  266 devices, 21 uclasses, devicetree: separate
MMC:   mmc@fe2b0000: 1, mmc@fe310000: 0
Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: Pine64 RK3566 Quartz64-A Board
can't get vref-supply: -2
rockchip_dnl_key_pressed: adc_channel_single_shot fail!
Net:   No ethernet found.
Hit any key to stop autoboot:  0
starting USB...
Bus usb@fcc00000: Port not available.
Bus usb@fd000000: Port not available.
Bus usb@fd800000: USB EHCI 1.00
Bus usb@fd840000: USB OHCI 1.0
Bus usb@fd880000: USB EHCI 1.00
Bus usb@fd8c0000: USB OHCI 1.0
scanning bus usb@fd800000 for devices... 1 USB Device(s) found
scanning bus usb@fd840000 for devices... ERROR:  USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did
not provide a handshake (OUT) (5)
unable to get device descriptor (error=-1)
1 USB Device(s) found
scanning bus usb@fd880000 for devices... 1 USB Device(s) found
scanning bus usb@fd8c0000 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
1: Armbian
Retrieving file: /boot/uInitrd
Retrieving file: /boot/Image
append: root=UUID=7f9c9970-93ba-46ca-9f03-f3241712ead8 console=ttyS02,1500000 console=tty0 rw no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 splash plymouth.ignore-
serial-consoles
Retrieving file: /boot/dtb/rockchip/rk3566-quartz64-a.dtb
Moving Image from 0x2080000 to 0x2200000, end=3de0000
## Loading init Ramdisk from Legacy Image at 0a200000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    34402446 Bytes = 32.8 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 0a100000
   Booting using the fdt blob at 0xa100000
   Loading Ramdisk to 7be16000, end 7dee508e ... OK
   Loading Device Tree to 000000007bdf7000, end 000000007be158e2 ... OK

Starting kernel ...

Quoted 8 lines

efi_free_pool: illegal free 0x000000007cee7040
efi_free_pool: illegal free 0x000000007cee4040
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[    0.000000] Linux version 6.2.0-rc6-media (root@d00a59921686) (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the
A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321) #trunk.0252 SMP PREEMPT_DYNAMIC Sat Feb 11 22:41:21 UTC 2023
[    0.000000] Machine model: Pine64 RK3566 Quartz64-A Board

Thanks!

Chris

Signature · 13 lines
Christopher Obbard BEng (Hons) MIET
Senior Engineer

Collabora Ltd
Platinum Building, St John's Innovation Park, Cambridge CB4 0DS, UK
Registered in England & Wales no 5513718.
This message is intended for the use of only the person(s) ("intended
recipient") to whom it is addressed. 
It may contain information that is privileged and confidential.
Accordingly, any dissemination, distribution, copying or other use of
this message or any of its content by any person other than the
intended recipient may constitute a breach of civil or criminal law and
is strictly prohibited.
#10 lore raw

Re: [PATCH 1/5] board: rockchip: Add Pine64 Quartz64-A Board

Hi Jonas,

Quoted 279 lines · Christopher Obbard

Hi Jonas,

Quoted 210 lines · Jonas Karlman
Quoted 209 lines · Jonas Karlman

Hi Christopher,

Quoted 166 lines · Christopher Obbard

Hi Jonas,

Quoted 137 lines · Christopher Obbard

Hi Jonas,

Sorry for the late response, I've been meaning to test this for a while but not got around to it.

Quoted 62 lines · Jonas Karlman

Hi Christopher,

Quoted 53 lines · Christopher Obbard

Hi Jonas,

Quoted 46 lines · Jonas Karlman
Quoted 14 lines · Jonas Karlman

The Pine64 Quartz64 Model A is a single-board computer based on the
Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0,
CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a
20 pin GPIO header.

Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Quoted 8 lines

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli
<[email protected]>
Signed-off-by: Nicolas Frattaroli
<[email protected]>

---

[...]

Boot log with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf:

[...]

U-Boot 2023.07 (Jul 23 2023 - 12:42:18 +0000)

Model: Pine64 RK3566 Quartz64-A Board
DRAM:  8 GiB (effective 7.7 GiB)
PMIC:  RK8170 (on=0x10, off=0x00)
Core:  321 devices, 27 uclasses, devicetree: separate MMC:   rockchip_sdhci_probe clk set rate fail! mmc@fe2b0000: 1, mmc@fe2c0000: 2, mmc@fe310000: 0 Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: Pine64 RK3566 Quartz64-A Board
Net:   No ethernet found.

Quoted 2 lines

Hit any key to stop autoboot:  0
=>

Quoted 5 lines

I just tried booting U-Boot v2023.10-rc2 with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf, on my Quartz64-A but it fails during loading of some parts. I removed the output of the RK TPL from my logs as there were no errors.

Quoted 3 lines

Try with latest rk3566_ddr_1056MHz_v1.18.bin and see if that makes any
difference.

No difference.

I've also checked, there is no other maskrom bootable media such as SPI flash connected to the board.

Quoted 4 lines
Quoted 2 lines

This is when booting from eMMC.

Does it boot with SD-card or other eMMC modules?

Booting from SD card (without eMMC connected), everything works fine.

Quoted 9 lines
Quoted 4 lines

I also tried building your branch from
https://github.com/Kwiboo/u-boot-rockchip/tree/rk3568-2023.10

Please try with a GitHub actions built u-boot-rockchip.bin based on my
rk3568-2023.07.02 branch at
https://github.com/Kwiboo/u-boot-build/actions/runs/5777761235

With that exact artifact, flashed with:

Quoted 4 lines

rkdeveloptool db rk356x_spl_loader_v1.18.113.bin
rkdeveloptool ef
rkdeveloptool wl 64 u-boot-rockchip.bin
rkdeveloptool rd

it fails to boot with with:

Quoted 21 lines

DDR V1.18 f366f69a7d typ 23/07/17-15:48:58
ln
LP4/4x derate en, other dram:1x trefi
SRX
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=8 Size=8192MB

change to: 324MHz
clk skew:0x60

change to: 528MHz
clk skew:0x58

change to: 780MHz
clk skew:0x58

change to: 1056MHz(final freq)
clk skew:0x32
out

Quoted 11 lines

U-Boot SPL 2023.07.02-g09919887 (Aug 06 2023 - 16:59:31 +0000) Trying to boot from MMC1
spl: mmc init failed with error: -70
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc fail to send stop cmd
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Quoted 2 lines

I also tried a second eMMC, but it also failed to boot with the same "mmc block read error" message.

I tried with your latest branch
https://github.com/Kwiboo/u-boot-rockchip/commits/rk3568-2023.10

and this time a different error message, loading from the eMMC appears to get a bit further:

Quoted 5 lines

U-Boot SPL 2023.10-00054-gef68159087 (Oct 12 2023 - 12:14:22 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 0 (ret = -5)

Quoted 8 lines

mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

So this is pointing to an issue reading from the MMC...

Quoted 24 lines

I found
https://lists.denx.de/pipermail/u-boot/2023-April/514315.html (which
is applied to your branch) and added the following to defconfig:

CONFIG_MMC_SDHCI_SDMA=y
+# CONFIG_SPL_MMC_SDHCI_SDMA is not set

but this seemed to make the loading less reliable:

Quoted 13 lines

U-Boot SPL 2023.10-00054-gef68159087-dirty (Oct 12 2023 - 12:23:10 +0100)
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
mmc fail to send stop cmd
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Thanks for testing different combinations.

I did find an issue with emmc write using ddr52 and hs400 modes on rk3568. On rk3588 emmc write only worked reliable after hs200 mode had been used.

Please try the changes from following commit, or my rk35xx-2024.01 work-in-progress branch:

WIP: rockchip: rk35xx: improve emmc write
https://github.com/Kwiboo/u-boot-rockchip/commit/aa6156179bb2034e8ba26753e05285e276327d78

Most rk356x boards currently default to ddr52 mode, and possible emmc read is also affected with similar issue as emmc write.

Quoted 8 lines
Quoted 3 lines

I have also discovered a strange issue on an Amlogic soc related to U-Boot mmc commands and gcc optimization, please see following patch:
https://patchwork.ozlabs.org/patch/1839392/

Posted link to wrong patch, I meant the following patch:

[RFC] mmc: Remove alignment hole for cmdidx in struct mmc_cmd
https://patchwork.ozlabs.org/patch/1841495/

I just tried with your branch & this patch on top, it still fails to boot and seems to be random how far it gets through the loading phase. Again I've removed the ddr training log.
It seems to get further this time though...

Boot #1:

Quoted 6 lines

U-Boot SPL 2023.10-00055-g29313fff30 (Oct 17 2023 - 09:44:21 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
## Checking hash(es) for Image u-boot ... sha256+ OK <crash>

Boot #2:

Quoted 10 lines

U-Boot SPL 2023.10-00055-g29313fff30 (Oct 17 2023 - 09:44:21 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
## Checking hash(es) for Image u-boot ... sha256+ OK
## Checking hash(es) for Image fdt-1 ... sha256+ OK
## Checking hash(es) for Image atf-2 ... sha256+ OK
## Checking hash(es) for Image atf-3 ... sha256+ OK
## Checking hash(es) for Image atf-4 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 4 (ret = -5)

Quoted 8 lines

mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Boot #3:

Quoted 10 lines

U-Boot SPL 2023.10-00055-g29313fff30 (Oct 17 2023 - 09:44:21 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
## Checking hash(es) for Image u-boot ... sha256+ OK
## Checking hash(es) for Image fdt-1 ... sha256+ OK
## Checking hash(es) for Image atf-2 ... sha256+ OK
## Checking hash(es) for Image atf-3 ... sha256+ OK
## Checking hash(es) for Image atf-4 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 4 (ret = -5)

Quoted 9 lines

mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Quoted 6 lines

For reference I am using gcc from Debian unstable:

Quoted 2 lines
$ aarch64-linux-gnu-gcc --version
aarch64-linux-gnu-gcc (Debian 13.2.0-2) 13.2.0

I can test with alternative cross-compiler if that would be useful.

Sorry to revive an old thread, but I managed to do some more testing with this board. I found that my Quartz64-a booting from eMMC is still broken with U- Boot main branch, as well as your WIP branches on GitHub. It fails with e.g:

U-Boot SPL 2024.07-rc4-00480-g51c2936ec989 (Jul 05 2024 - 15:30:33 +0100) Trying to boot from MMC1
spl: mmc init failed with error: -110
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
spl: mmc init failed with error: -70
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

The only thing which I have found to work, is pgwipeout's U-Boot branch, with the following binary blobs (The same U-Boot branch doesn't seem to work with the latest version of the BL31 blob. Seems to need that specific BL31. This is very, very strange to me.)

The DDR bin seems to be unaffected, but I included a working version below anyway.
https://github.com/rockchip-linux/rkbin/raw/6186debcac95553f6b311cee10669e12c9c9963d/bin/rk35/rk3568_bl31_v1.28.elf

https://github.com/rockchip-linux/rkbin/raw/ddf03c1d80b33dac72a33c4f732fc5849b47ff99/bin/rk35/rk3568_ddr_1560MHz_v1.13.bin

To make Peter's branch build, you need to set BL31 and move the DDR bin to ram_init.bin

I tried to forward-port some of the changes to U-Boot mainline, but the same error.

@Peter, can you try and confirm the error booting from eMMC on Quartz64-A with mainline U-Boot ?

Quoted 307 lines

Thanks,
Chris

Quoted 303 lines

Regards,
Jonas

Quoted 298 lines

Please try with CONFIG_MMC_TRACE=y to see what commands fails on your device.

If above patches does not work also try with following options applied:

CONFIG_MMC_HS200_SUPPORT=y
CONFIG_SPL_MMC_HS200_SUPPORT=y

Use of HS200 seem to be the most reliable option on rk35xx based on my limited testing.

Quoted 35 lines

...

Quoted 15 lines
Quoted 15 lines

What happens if you write u-boot-rockchip.bin to eMMC module usinga USB adapter:

  dd if=u-boot-rockchip.bin of=/dev/<device> bs=32k seek=1 conv=fsync

or using U-Boot cmd when booted from a SD-card?

  # Read u-boot-rockchip.bin from first partition of a SD card load mmc 1:1 10000000 u-boot-rockchip.bin

  # Change to eMMC
  mmc dev 0

Quoted 7 lines
Quoted 4 lines

  # Write 10 MiB (0x5000 blocks) at sector 64 (0x40) mmc write $fileaddr 40 5000

Does that make any difference?

I don't think I have an eMMC writer for Pine64 eMMCs, I will try to get hold of one this week.

I have two USB writers. Anyway, the first boot, it fails with:

Quoted 6 lines

U-Boot SPL 2023.10-00054-gef68159087 (Oct 12 2023 - 12:30:14 +0100) Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
## Checking hash(es) for Image u-boot ... sha256+ OK <hang>

Quoted 54 lines

Then again after a reset:

Quoted 52 lines

U-Boot SPL 2023.10-00054-gef68159087 (Oct 12 2023 - 12:30:14 +0100) Trying to boot from MMC1
mmc fail to send stop cmd
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

But it fails to write to the eMMC with:

Quoted 21 lines

=> load mmc 1:2 10000000 u-boot-rockchip.bin
9510400 bytes read in 791 ms (11.5 MiB/s)

=> mmc dev 0
switch to partitions #0, OK
mmc0(part 0) is current device

=> mmc write $fileaddr 40 5000
MMC write: dev # 0, block # 64, count 20480 ... mmc write failed 0 blocks written: ERROR

=> mmc info
Device: mmc@fe310000
Manufacturer ID: 45
OEM: 0
Name: DF4016
Bus Speed: 52000000
Mode: MMC DDR52 (52MHz)
Rd Block Len: 512
MMC version 5.1

Quoted 8 lines

High Capacity: Yes
Capacity: 14.7 GiB
Bus Width: 8-bit DDR
Erase Group Size: 512 KiB
HC WP Group Size: 8 MiB
User Capacity: 14.7 GiB WRREL
Boot Capacity: 4 MiB ENH
RPMB Capacity: 4 MiB ENH

I think this points to some issue with the mmc driver in U-Boot, or possibly some issue with my board. But I find that hard to believe because the Rockchip usbloader seems to write to the eMMC just
fine ?

Probably related to sdhci driver and rx/tx tap and/or delay num etc.

Quoted 44 lines
Quoted 44 lines
Quoted 44 lines
Quoted 5 lines

Boot log (v2023.10-rc2):

Quoted 8 lines

U-Boot SPL 2023.10-rc2 (Aug 08 2023 - 14:02:34 +0100) rockchip_sdhci_probe clk set rate fail! Trying to boot from MMC1
spl: mmc init failed with error: -110
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1

Strange that second try of eMMC (MMC1) gets little bit longer.

Quoted 11 lines

## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
spl_load_simple_fit: can't load image loadables index 0 (ret = -
5)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Boot log (your branch):

Quoted 12 lines

U-Boot SPL 2023.10-rc1-00368-g16cb31d427 (Aug 08 2023 - 15:17:35 +0100)
Trying to boot from MMC1
spl: mmc init failed with error: -70
Trying to boot from MMC2
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

I have not been able to reproduce this kind of issue on any of my two
Quartz64-A boards, tested with different eMMC modules.

Quoted 6 lines
Quoted 6 lines
Quoted 3 lines

Does your eMMC module have some compatibility issue? Do you have any more details on the eMMC module you have tested with?

I have two eMMCs, one from FORESEE which came with a Pine64 and one marked SanDisk (which I posted the mmc info for above).

My eMMC modules is also FORESEE or SanDisk, from Pine64, Radxa and Hardkernel.

Quoted 3 lines
Quoted 3 lines

My hardware is marked Quartz64-RK3399-V2.0 2021-04-27 Maybe there is some difference with your board?

Should match my board, I have the hw revision where SATA port is removed.
(boards with/without SATA have same version silk on the board)

Quoted 8 lines
Quoted 2 lines

I will also try an image with vendor u-boot as a next step.

I tried latest Armbian (which seems to use ) from
https://github.com/armbian/build/releases/ and flashed the eMMC with the USB writer. It ended up booting to Linux, which proves that the hardware I
have is most likey in a good working order ;-)!

Hopefully the issue is related to the peephole2 optimization issue or the use of a not fully supported ddr52 mode.

Regards,
Jonas

Quoted 116 lines
Quoted 97 lines

U-Boot SPL 2022.10-rc4-armbian (Feb 11 2023 - 22:25:16 +0000) saradc@fe720000: Can't update Vdd. Error: -38saradc@fe720000: Can't update Vss. Error: -38can't get vref-supply: -38
rockchip_dnl_key_pressed: adc_channel_single_shot fail! Trying to boot from MMC2
INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-152-g4e725b15f:cl
NOTICE:  BL31: Built : 10:51:13, Jul 15 2021
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    pmu v1 is valid
INFO:    dfs DDR fsp_param[0].freq_mhz= 1560MHz
INFO:    dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO:    dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO:    dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast INFO:    BL31: Preparing for EL3 exit to normal world INFO:    Entry point address = 0xa00000
INFO:    SPSR = 0x3c9

U-Boot 2022.10-rc4-armbian (Feb 11 2023 - 22:25:16 +0000)

Model: Pine64 RK3566 Quartz64-A Board
DRAM:  2 GiB
PMIC:  RK8170 (on=0x10, off=0x00)
Core:  266 devices, 21 uclasses, devicetree: separate MMC:   mmc@fe2b0000: 1, mmc@fe310000: 0
Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: Pine64 RK3566 Quartz64-A Board
can't get vref-supply: -2
rockchip_dnl_key_pressed: adc_channel_single_shot fail! Net:   No ethernet found.
Hit any key to stop autoboot:  0
starting USB...
Bus usb@fcc00000: Port not available.
Bus usb@fd000000: Port not available.
Bus usb@fd800000: USB EHCI 1.00
Bus usb@fd840000: USB OHCI 1.0
Bus usb@fd880000: USB EHCI 1.00
Bus usb@fd8c0000: USB OHCI 1.0
scanning bus usb@fd800000 for devices... 1 USB Device(s) found scanning bus usb@fd840000 for devices... ERROR:  USB-error:
DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did
not provide a handshake (OUT) (5)
unable to get device descriptor (error=-1)
1 USB Device(s) found
scanning bus usb@fd880000 for devices... 1 USB Device(s) found scanning bus usb@fd8c0000 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
1: Armbian
Retrieving file: /boot/uInitrd
Retrieving file: /boot/Image
append: root=UUID=7f9c9970-93ba-46ca-9f03-f3241712ead8 console=ttyS02,1500000 console=tty0 rw no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 splash plymouth.ignore-
serial-consoles
Retrieving file: /boot/dtb/rockchip/rk3566-quartz64-a.dtb Moving Image from 0x2080000 to 0x2200000, end=3de0000
## Loading init Ramdisk from Legacy Image at 0a200000 ... Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed) Data Size:    34402446 Bytes = 32.8 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 0a100000
   Booting using the fdt blob at 0xa100000
   Loading Ramdisk to 7be16000, end 7dee508e ... OK Loading Device Tree to 000000007bdf7000, end 000000007be158e2 ... OK

Starting kernel ...

Quoted 12 lines

efi_free_pool: illegal free 0x000000007cee7040
efi_free_pool: illegal free 0x000000007cee4040
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[    0.000000] Linux version 6.2.0-rc6-media (root@d00a59921686) (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the
A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321) #trunk.0252 SMP PREEMPT_DYNAMIC Sat Feb 11 22:41:21 UTC 2023 [    0.000000] Machine model: Pine64 RK3566 Quartz64-A Board

Thanks!

Chris

Reviewed-by on v1 1/5
#11 lore raw

Re: [PATCH 1/5] board: rockchip: Add Pine64 Quartz64-A Board

In reply to Jonas Karlman
Quoted 11 lines · Jonas Karlman

The Pine64 Quartz64 Model A is a single-board computer based on the Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0, CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a 20 pin GPIO header.

Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Quoted 5 lines

Device tree is imported from linux v6.4.

Thanks,
- Kever

Quoted 1,159 lines
---
  arch/arm/dts/Makefile                         |   1 +
  arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi    |  55 ++
  arch/arm/dts/rk3566-quartz64-a.dts            | 839 ++++++++++++++++++
  arch/arm/mach-rockchip/rk3568/Kconfig         |   6 +
  board/pine64/quartz64_rk3566/Kconfig          |  15 +
  board/pine64/quartz64_rk3566/MAINTAINERS      |   9 +
  board/pine64/quartz64_rk3566/Makefile         |   3 +
  .../pine64/quartz64_rk3566/quartz64-rk3566.c  |   1 +
  configs/quartz64-a-rk3566_defconfig           | 110 +++
  doc/board/rockchip/rockchip.rst               |   1 +
  include/configs/quartz64_rk3566.h             |  10 +
  11 files changed, 1050 insertions(+)

create mode 100644 arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-quartz64-a.dts create mode 100644 board/pine64/quartz64_rk3566/Kconfig create mode 100644 board/pine64/quartz64_rk3566/MAINTAINERS create mode 100644 board/pine64/quartz64_rk3566/Makefile create mode 100644 board/pine64/quartz64_rk3566/quartz64-rk3566.c create mode 100644 configs/quartz64-a-rk3566_defconfig create mode 100644 include/configs/quartz64_rk3566.h

arch/arm/dts/Makefile +1 -0
index 6764ded580ab..45ef73fdf0ca 100644
@@ -167,6 +167,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \
 
  dtb-$(CONFIG_ROCKCHIP_RK3568) += \
  	rk3566-anbernic-rgxx3.dtb \
+	rk3566-quartz64-a.dtb \
  	rk3566-radxa-cm3-io.dtb \
  	rk3568-evb.dtb \
  	rk3568-odroid-m1.dtb \
arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi new file +55 -0
new file mode 100644
index 000000000000..700c2d3edfe6
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk356x-u-boot.dtsi"
+
+/ {
+	chosen {
+		stdout-path = &uart2;
+	};
+};
+
+&gpio0 {
+	bootph-all;
+};
+
+&pcie2x1 {
+	pinctrl-0 = <&pcie20m2_pins &pcie_reset_h>;
+};
+
+&sdhci {
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+};
+
+&sfc {
+	bootph-pre-ram;
+	u-boot,spl-sfc-no-dma;
+
+	flash@0 {
+		bootph-pre-ram;
+	};
+};
+
+&uart2 {
+	bootph-all;
+	clock-frequency = <24000000>;
+	status = "okay";
+};
+
+/*
+ * U-Boot does not support multiple regulators using the same gpio,
+ * use vcc5v0_usb20_host to fix use of USB 2.0 port
+ */
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb20_host>;
+};
+
+&vcc3v3_sd {
+	bootph-pre-ram;
+};
+
+&vcc_sd_h {
+	bootph-all;
+};
arch/arm/dts/rk3566-quartz64-a.dts new file +839 -0
new file mode 100644
index 000000000000..25a8c781f4e7
@@ -0,0 +1,839 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+	model = "Pine64 RK3566 Quartz64-A Board";
+	compatible = "pine64,quartz64-a", "rockchip,rk3566";
+
+	aliases {
+		ethernet0 = &gmac1;
+		mmc0 = &sdmmc0;
+		mmc1 = &sdhci;
+	};
+
+	chosen: chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	gmac1_clkin: external-gmac1-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac1_clkin";
+		#clock-cells = <0>;
+	};
+
+	fan: gpio_fan {
+		compatible = "gpio-fan";
+		gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
+		gpio-fan,speed-map = <0    0
+				      4500 1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&fan_en_h>;
+		#cooling-cells = <2>;
+	};
+
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-work {
+			label = "work-led";
+			default-state = "off";
+			gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&work_led_enable_h>;
+			retain-state-suspended;
+		};
+
+		led-diy {
+			label = "diy-led";
+			default-state = "on";
+			gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			pinctrl-names = "default";
+			pinctrl-0 = <&diy_led_enable_h>;
+			retain-state-suspended;
+		};
+	};
+
+	rk817-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,name = "Analog RK817";
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s1_8ch>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&rk817>;
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk817 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+		post-power-on-delay-ms = <100>;
+		power-off-delay-us = <5000000>;
+		reset-gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_LOW>;
+	};
+
+	spdif_dit: spdif-dit {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
+	spdif_sound: spdif-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "SPDIF";
+
+		simple-audio-card,cpu {
+			sound-dai = <&spdif>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&spdif_dit>;
+		};
+	};
+
+	vcc12v_dcin: vcc12v_dcin {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	/* vbus feeds the rk817 usb input.
+	 * With no battery attached, also feeds vcc_bat+
+	 * via ON/OFF_BAT jumper
+	 */
+	vbus: vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc3v3_pcie_p: vcc3v3-pcie-p-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie_enable_h>;
+		regulator-name = "vcc3v3_pcie_p";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3>;
+	};
+
+	vcc5v0_usb: vcc5v0_usb {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	/* all four ports are controlled by one gpio
+	 * the host ports are sourced from vcc5v0_usb
+	 * the otg port is sourced from vcc5v0_midu
+	 */
+	vcc5v0_usb20_host: vcc5v0_usb20_host {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb20_host_en>;
+		regulator-name = "vcc5v0_usb20_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
+	vcc5v0_usb20_otg: vcc5v0_usb20_otg {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
+		regulator-name = "vcc5v0_usb20_otg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dcdc_boost>;
+	};
+
+	vcc3v3_sd: vcc3v3_sd {
+		compatible = "regulator-fixed";
+		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc_sd_h>;
+		regulator-boot-on;
+		regulator-name = "vcc3v3_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3>;
+	};
+
+	/* sourced from vbus and vcc_bat+ via rk817 sw5 */
+	vcc_sys: vcc_sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <4400000>;
+		regulator-max-microvolt = <4400000>;
+		vin-supply = <&vbus>;
+	};
+
+	/* sourced from vcc_sys, sdio module operates internally at 3.3v */
+	vcc_wl: vcc_wl {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_wl";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_sys>;
+	};
+};
+
+&combphy1 {
+	status = "okay";
+};
+
+&combphy2 {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_thermal {
+	trips {
+		cpu_hot: cpu_hot {
+			temperature = <55000>;
+			hysteresis = <2000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map1 {
+			trip = <&cpu_hot>;
+			cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>, <&gmac1_clkin>;
+	clock_in_out = "input";
+	phy-supply = <&vcc_3v3>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m0_miim
+		     &gmac1m0_tx_bus2
+		     &gmac1m0_rx_bus2
+		     &gmac1m0_rgmii_clk
+		     &gmac1m0_clkinout
+		     &gmac1m0_rgmii_bus>;
+	snps,reset-gpio = <&gpio0 RK_PC3 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	/* Reset time is 20ms, 100ms for rtl8211f */
+	snps,reset-delays-us = <0 20000 100000>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	phy-handle = <&rgmii_phy1>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vdda_0v9>;
+	avdd-1v8-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	vdd_cpu: regulator@1c {
+		compatible = "tcs,tcs4525";
+		reg = <0x1c>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <2300>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	rk817: pmic@20 {
+		compatible = "rockchip,rk817";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+		clock-names = "mclk";
+		clocks = <&cru I2S1_MCLKOUT_TX>;
+		clock-output-names = "rk808-clkout1", "rk808-clkout2";
+		#clock-cells = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>;
+		rockchip,system-power-controller;
+		#sound-dai-cells = <0>;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc5-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
+		vcc8-supply = <&vcc_sys>;
+		vcc9-supply = <&dcdc_boost>;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vdd_logic";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vdd_gpu";
+					regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vcc_ddr";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_3v3: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vcc_3v3";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca1v8_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdda_0v9";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdda0v9_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_acodec";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_1v8: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_1v8";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc1v8_dvp: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8_dvp";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc2v8_dvp: LDO_REG9 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-name = "vcc2v8_dvp";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			dcdc_boost: BOOST {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+				regulator-name = "boost";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			otg_switch: OTG_SWITCH {
+				regulator-name = "otg_switch";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+/* i2c3 is exposed on con40
+ * pin 3 - i2c3_sda_m0, pullup to vcc_3v3
+ * pin 5 - i2c3_scl_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+	status = "okay";
+};
+
+&i2s0_8ch {
+	status = "okay";
+};
+
+&i2s1_8ch {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s1m0_sclktx
+		     &i2s1m0_lrcktx
+		     &i2s1m0_sdi0
+		     &i2s1m0_sdo0>;
+	rockchip,trcm-sync-tx-only;
+	status = "okay";
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&pcie2x1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_reset_h>;
+	reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie_p>;
+	status = "okay";
+};
+
+&pinctrl {
+	bt {
+		bt_enable_h: bt-enable-h {
+			rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_host_wake_l: bt-host-wake-l {
+			rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		bt_wake_l: bt-wake-l {
+			rockchip,pins = <2 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	fan {
+		fan_en_h: fan-en-h {
+			rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	leds {
+		work_led_enable_h: work-led-enable-h {
+			rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		diy_led_enable_h: diy-led-enable-h {
+			rockchip,pins = <0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		pcie_enable_h: pcie-enable-h {
+			rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		pcie_reset_h: pcie-reset-h {
+			rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb2 {
+		vcc5v0_usb20_host_en: vcc5v0-usb20-host-en {
+			rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	vcc_sd {
+		vcc_sd_h: vcc-sd-h {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcc3v3_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio2-supply = <&vcc_1v8>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_1v8>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc1v8_dvp>;
+	vccio7-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc_wl>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sfc {
+	pinctrl-0 = <&fspi_pins>;
+	pinctrl-names = "default";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "disabled";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
+	};
+};
+
+/* spdif is exposed on con40 pin 18 */
+&spdif {
+	status = "okay";
+};
+
+/* spi1 is exposed on con40
+ * pin 11 - spi1_mosi_m1
+ * pin 13 - spi1_miso_m1
+ * pin 15 - spi1_clk_m1
+ * pin 17 - spi1_cs0_m1
+ */
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1m1_cs0 &spi1m1_pins>;
+};
+
+&tsadc {
+	/* tshut mode 0:CRU 1:GPIO */
+	rockchip,hw-tshut-mode = <1>;
+	/* tshut polarity 0:LOW 1:HIGH */
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+/* uart0 is exposed on con40
+ * pin 12 - uart0_tx
+ * pin 14 - uart0_rx
+ */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
+	status = "okay";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rk817 1>;
+		clock-names = "lpo";
+		host-wakeup-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+		vbat-supply = <&vcc_sys>;
+		vddio-supply = <&vcca1v8_pmu>;
+		max-speed = <3000000>;
+	};
+};
+
+/* uart2 is exposed on con40
+ * pin 8 - uart2_tx_m0_debug
+ * pin 10 - uart2_rx_m0_debug
+ */
+&uart2 {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	dr_mode = "host";
+	status = "okay";
+};
+
+/* usb3 controller is muxed with sata1 */
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb20_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb20_otg>;
+	status = "okay";
+};
+
+&usb2phy1 {
+	status = "okay";
+};
+
+&usb2phy1_host {
+	phy-supply = <&vcc5v0_usb20_host>;
+	status = "okay";
+};
+
+&usb2phy1_otg {
+	phy-supply = <&vcc5v0_usb20_host>;
+	status = "okay";
+};
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
arch/arm/mach-rockchip/rk3568/Kconfig +6 -0
index f46be3d081fe..baa51349f4be 100644
@@ -22,6 +22,11 @@ config TARGET_ODROID_M1_RK3568
  	help
  	  Hardkernel ODROID-M1 single board computer with a RK3568B2 SoC.
 
+config TARGET_QUARTZ64_RK3566
+	bool "Pine64 Quartz64"
+	help
+	  Pine64 Quartz64 single board computer with a RK3566 SoC.
+
  endchoice
 
  config ROCKCHIP_BOOT_MODE_REG
@@ -39,5 +44,6 @@ config SYS_MALLOC_F_LEN
  source "board/rockchip/evb_rk3568/Kconfig"
  source "board/anbernic/rgxx3_rk3566/Kconfig"
  source "board/hardkernel/odroid_m1/Kconfig"
+source "board/pine64/quartz64_rk3566/Kconfig"
 
  endif
board/pine64/quartz64_rk3566/Kconfig new file +15 -0
new file mode 100644
index 000000000000..3de1d8f7a993
@@ -0,0 +1,15 @@
+if TARGET_QUARTZ64_RK3566
+
+config SYS_BOARD
+	default "quartz64_rk3566"
+
+config SYS_VENDOR
+	default "pine64"
+
+config SYS_CONFIG_NAME
+	default "quartz64_rk3566"
+
+config BOARD_SPECIFIC_OPTIONS # dummy
+	def_bool y
+
+endif
board/pine64/quartz64_rk3566/MAINTAINERS new file +9 -0
new file mode 100644
index 000000000000..dbc0dfbd9787
@@ -0,0 +1,9 @@
+QUARTZ64-RK3566
+M:	Nicolas Frattaroli <[email protected]>
+R:	Jonas Karlman <[email protected]>
+S:	Maintained
+F:	board/pine64/quartz64_rk3566/
+F:	include/configs/quartz64_rk3566.h
+F:	configs/quartz64-a-rk3566_defconfig
+F:	arch/arm/dts/rk3566-quartz64-a.dts
+F:	arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
board/pine64/quartz64_rk3566/Makefile new file +3 -0
new file mode 100644
index 000000000000..c24a40e724d7
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+obj-y	+= quartz64-rk3566.o
board/pine64/quartz64_rk3566/quartz64-rk3566.c new file +1 -0
new file mode 100644
index 000000000000..4c027f2a7af9
@@ -0,0 +1 @@
+// SPDX-License-Identifier: GPL-2.0+
configs/quartz64-a-rk3566_defconfig new file +110 -0
new file mode 100644
index 000000000000..d55b224feacd
@@ -0,0 +1,110 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TEXT_BASE=0x00a00000
+CONFIG_SPL_GPIO=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
+CONFIG_SF_DEFAULT_SPEED=24000000
+CONFIG_SF_DEFAULT_MODE=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="rk3566-quartz64-a"
+CONFIG_ROCKCHIP_RK3568=y
+CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
+CONFIG_ROCKCHIP_SPI_IMAGE=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_TARGET_QUARTZ64_RK3566=y
+CONFIG_SPL_STACK=0x400000
+CONFIG_DEBUG_UART_BASE=0xFE660000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SPL_SPI_FLASH_SUPPORT=y
+CONFIG_SPL_SPI=y
+CONFIG_SYS_LOAD_ADDR=0xc00800
+CONFIG_PCI=y
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_FIT_SIGNATURE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-quartz64-a.dtb"
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_MAX_SIZE=0x40000
+CONFIG_SPL_PAD_TO=0x7f8000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x4000000
+CONFIG_SPL_BSS_MAX_SIZE=0x4000
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_POWER=y
+CONFIG_SPL_SPI_LOAD=y
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000
+CONFIG_SPL_ATF=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIVE=y
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_SYSCON=y
+CONFIG_SCSI_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_SPL_CLK=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
+CONFIG_SUPPORT_EMMC_RPMB=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_ROCKCHIP=y
+CONFIG_SF_DEFAULT_BUS=4
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_GIGADEVICE=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_NVME_PCI=y
+CONFIG_PCIE_DW_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_SPL_DM_REGULATOR=y
+CONFIG_SPL_DM_REGULATOR_FIXED=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_SPL_RAM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_BAUDRATE=1500000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_ROCKCHIP_SFC=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_GENERIC=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_ERRNO_STR=y
doc/board/rockchip/rockchip.rst +1 -0
index b89f35954d33..c7d4c835db80 100644
@@ -96,6 +96,7 @@ List of mainline supported Rockchip boards:
  * rk3568
       - Rockchip Evb-RK3568 (evb-rk3568)
       - Hardkernel ODROID-M1 (odroid-m1-rk3568)
+     - Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig)
 
  * rk3588
       - Rockchip EVB (evb-rk3588)
include/configs/quartz64_rk3566.h new file +10 -0
new file mode 100644
index 000000000000..dfe0fee94cdb
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+
+#ifndef __QUARTZ64_RK3566_H
+#define __QUARTZ64_RK3566_H
+
+#define ROCKCHIP_DEVICE_SETTINGS
+
+#include <configs/rk3568_common.h>
+
+#endif
#12 lore raw

PATCH 2/5 board: rockchip: Add Pine64 Quartz64-B Board

In reply to Jonas Karlman

The Pine64 Quartz64 Model B is a credit-card sized single-board computer based on the Rockchip RK3566 SoC. The board features an M.2 PCIe slot, USB3, USB2, eMMC, SD, ethernet, HDMI, analog audio out, a 40 pin GPIO header and a DSI and CSI port, as well as on-board Wi-Fi.

Features tested on a Quartz64-B 4GB v1.4 2022-06-06:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB host

Device tree is imported from linux v6.4.

---
 arch/arm/dts/Makefile                      |   1 +
 arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi |  47 ++
 arch/arm/dts/rk3566-quartz64-b.dts         | 739 +++++++++++++++++++++
 board/pine64/quartz64_rk3566/MAINTAINERS   |   3 +
 configs/quartz64-b-rk3566_defconfig        | 106 +++
 doc/board/rockchip/rockchip.rst            |   1 +
 6 files changed, 897 insertions(+)
 create mode 100644 arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi
 create mode 100644 arch/arm/dts/rk3566-quartz64-b.dts
 create mode 100644 configs/quartz64-b-rk3566_defconfig
arch/arm/dts/Makefile +1 -0
index 45ef73fdf0ca..3cc921e5cc1e 100644
@@ -168,6 +168,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \
 dtb-$(CONFIG_ROCKCHIP_RK3568) += \
 	rk3566-anbernic-rgxx3.dtb \
 	rk3566-quartz64-a.dtb \
+	rk3566-quartz64-b.dtb \
 	rk3566-radxa-cm3-io.dtb \
 	rk3568-evb.dtb \
 	rk3568-odroid-m1.dtb \
arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi new file +47 -0

47 lines not on this page · raw message

arch/arm/dts/rk3566-quartz64-b.dts new file +739 -0

739 lines not on this page · raw message

board/pine64/quartz64_rk3566/MAINTAINERS +3 -0
index dbc0dfbd9787..2e637bf51ba3 100644
@@ -5,5 +5,8 @@ S:	Maintained
 F:	board/pine64/quartz64_rk3566/
 F:	include/configs/quartz64_rk3566.h
 F:	configs/quartz64-a-rk3566_defconfig
+F:	configs/quartz64-b-rk3566_defconfig
 F:	arch/arm/dts/rk3566-quartz64-a.dts
 F:	arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
+F:	arch/arm/dts/rk3566-quartz64-b.dts
+F:	arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi
configs/quartz64-b-rk3566_defconfig new file +106 -0

106 lines not on this page · raw message

doc/board/rockchip/rockchip.rst +1 -0
index c7d4c835db80..1c0e10c40607 100644
@@ -97,6 +97,7 @@ List of mainline supported Rockchip boards:
      - Rockchip Evb-RK3568 (evb-rk3568)
      - Hardkernel ODROID-M1 (odroid-m1-rk3568)
      - Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig)
+     - Pine64 Quartz64-B Board (quartz64-b-rk3566_defconfig)
 
 * rk3588
      - Rockchip EVB (evb-rk3588)
Signature · 1 line
2.41.0
#13 lore raw

Re: [PATCH 2/5] board: rockchip: Add Pine64 Quartz64-B Board

Quoted 12 lines · Jonas Karlman

The Pine64 Quartz64 Model B is a credit-card sized single-board computer based on the Rockchip RK3566 SoC. The board features an M.2 PCIe slot, USB3, USB2, eMMC, SD, ethernet, HDMI, analog audio out, a 40 pin GPIO header and a DSI and CSI port, as well as on-board Wi-Fi.

Features tested on a Quartz64-B 4GB v1.4 2022-06-06:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB host

Quoted 6 lines

Device tree is imported from linux v6.4.

---

[...]

Boot log with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin, BL31=rk3568_bl31_v1.43.elf and serial console on UART5:
U-Boot SPL 2023.07 (Jul 23 2023 - 13:52:36 +0000) rockchip_sdhci_probe clk set rate fail!
Trying to boot from MMC2
## Checking hash(es) for config config-1 ... OK ## Checking hash(es) for Image atf-1 ... sha256+ OK ## Checking hash(es) for Image u-boot ... sha256+ OK ## Checking hash(es) for Image fdt-1 ... sha256+ OK ## Checking hash(es) for Image atf-2 ... sha256+ OK ## Checking hash(es) for Image atf-3 ... sha256+ OK ## Checking hash(es) for Image atf-4 ... sha256+ OK ## Checking hash(es) for Image atf-5 ... sha256+ OK ## Checking hash(es) for Image atf-6 ... sha256+ OK

U-Boot 2023.07 (Jul 23 2023 - 13:52:36 +0000)

Model: Pine64 RK3566 Quartz64-B Board
DRAM:  4 GiB (effective 3.7 GiB)
PMIC:  RK8090 (on=0x40, off=0x00)
Core:  321 devices, 30 uclasses, devicetree: separate
MMC:   rockchip_sdhci_probe clk set rate fail!
mmc@fe2b0000: 1, mmc@fe2c0000: 2, mmc@fe310000: 0
Loading Environment from nowhere... OK
In:    serial@fe690000
Out:   serial@fe690000
Err:   serial@fe690000
Model: Pine64 RK3566 Quartz64-B Board
Net:   No ethernet found.

Hit any key to stop autoboot: 0
=>

Regards,
Jonas

Reviewed-by on v1 2/5
#14 lore raw

Re: [PATCH 2/5] board: rockchip: Add Pine64 Quartz64-B Board

In reply to Jonas Karlman
Quoted 12 lines · Jonas Karlman

The Pine64 Quartz64 Model B is a credit-card sized single-board computer based on the Rockchip RK3566 SoC. The board features an M.2 PCIe slot, USB3, USB2, eMMC, SD, ethernet, HDMI, analog audio out, a 40 pin GPIO header and a DSI and CSI port, as well as on-board Wi-Fi.

Features tested on a Quartz64-B 4GB v1.4 2022-06-06:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB host

Quoted 5 lines

Device tree is imported from linux v6.4.

Thanks,
- Kever

Quoted 959 lines
---
  arch/arm/dts/Makefile                      |   1 +
  arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi |  47 ++
  arch/arm/dts/rk3566-quartz64-b.dts         | 739 +++++++++++++++++++++
  board/pine64/quartz64_rk3566/MAINTAINERS   |   3 +
  configs/quartz64-b-rk3566_defconfig        | 106 +++
  doc/board/rockchip/rockchip.rst            |   1 +
  6 files changed, 897 insertions(+)

create mode 100644 arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-quartz64-b.dts create mode 100644 configs/quartz64-b-rk3566_defconfig

arch/arm/dts/Makefile +1 -0
index 45ef73fdf0ca..3cc921e5cc1e 100644
@@ -168,6 +168,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \
  dtb-$(CONFIG_ROCKCHIP_RK3568) += \
  	rk3566-anbernic-rgxx3.dtb \
  	rk3566-quartz64-a.dtb \
+	rk3566-quartz64-b.dtb \
  	rk3566-radxa-cm3-io.dtb \
  	rk3568-evb.dtb \
  	rk3568-odroid-m1.dtb \
arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi new file +47 -0
new file mode 100644
index 000000000000..bdbb921c66e2
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk356x-u-boot.dtsi"
+
+/ {
+	chosen {
+		stdout-path = &uart2;
+	};
+};
+
+&pcie2x1 {
+	pinctrl-0 = <&pcie20m2_pins &pcie_reset_h>;
+};
+
+&sdhci {
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+};
+
+&sfc {
+	bootph-pre-ram;
+	u-boot,spl-sfc-no-dma;
+
+	flash@0 {
+		bootph-pre-ram;
+	};
+};
+
+&uart2 {
+	bootph-all;
+	clock-frequency = <24000000>;
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	dr_mode = "host";
+};
+
+&vcc5v0_usb30_host {
+	/delete-property/ regulator-always-on;
+};
+
+&vcc5v0_usb_otg {
+	/delete-property/ regulator-always-on;
+};
arch/arm/dts/rk3566-quartz64-b.dts new file +739 -0
new file mode 100644
index 000000000000..b276eb0810c7
@@ -0,0 +1,739 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+	model = "Pine64 RK3566 Quartz64-B Board";
+	compatible = "pine64,quartz64-b", "rockchip,rk3566";
+
+	aliases {
+		ethernet0 = &gmac1;
+		mmc0 = &sdmmc0;
+		mmc1 = &sdhci;
+		mmc2 = &sdmmc1;
+	};
+
+	chosen: chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	gmac1_clkin: external-gmac1-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac1_clkin";
+		#clock-cells = <0>;
+	};
+
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-user {
+			label = "user-led";
+			default-state = "on";
+			gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			pinctrl-names = "default";
+			pinctrl-0 = <&user_led_enable_h>;
+			retain-state-suspended;
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,name = "Analog RK809";
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s1_8ch>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&rk809>;
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		status = "okay";
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk809 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+		reset-gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <100>;
+		power-off-delay-us = <5000000>;
+	};
+
+	vcc3v3_pcie_p: vcc3v3-pcie-p-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie_enable_h>;
+		regulator-name = "vcc3v3_pcie_p";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3>;
+	};
+
+	vcc5v0_in: vcc5v0-in-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_in";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_in>;
+	};
+
+	vcc3v3_sys: vcc3v3-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_usb30_host: vcc5v0-usb30-host-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb30_host";
+		enable-active-high;
+		gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb30_host_en_h>;
+		regulator-always-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_usb_otg: vcc5v0-usb-otg-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb_otg";
+		enable-active-high;
+		gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_otg_en_h>;
+		regulator-always-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+};
+
+&combphy1 {
+	status = "okay";
+};
+
+&combphy2 {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>, <&gmac1_clkin>;
+	clock_in_out = "input";
+	phy-mode = "rgmii";
+	phy-supply = <&vcc_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m1_miim
+		     &gmac1m1_tx_bus2
+		     &gmac1m1_rx_bus2
+		     &gmac1m1_rgmii_clk
+		     &gmac1m1_clkinout
+		     &gmac1m1_rgmii_bus>;
+	snps,reset-gpio = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	/* Reset time is 20ms, 100ms for rtl8211f, also works well here */
+	snps,reset-delays-us = <0 20000 100000>;
+	tx_delay = <0x4f>;
+	rx_delay = <0x24>;
+	phy-handle = <&rgmii_phy1>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vdda0v9_image>;
+	avdd-1v8-supply = <&vcca1v8_image>;
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	vdd_cpu: regulator@1c {
+		compatible = "tcs,tcs4525";
+		reg = <0x1c>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <2300>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+		clock-names = "mclk";
+		clocks = <&cru I2S1_MCLKOUT_TX>;
+		clock-output-names = "rk808-clkout1", "rk808-clkout2";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int>, <&i2s1m0_mclk>;
+		rockchip,system-power-controller;
+		#sound-dai-cells = <0>;
+		wakeup-source;
+		#clock-cells = <1>;
+
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc5-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+
+		regulators {
+			vdd_log: DCDC_REG1 {
+				regulator-name = "vdd_log";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_npu: DCDC_REG4 {
+				regulator-name = "vdd_npu";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-initial-mode = <0x2>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG5 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdda0v9_image: LDO_REG1 {
+				regulator-name = "vdda0v9_image";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-name = "vdda_0v9";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-name = "vdda0v9_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-name = "vccio_acodec";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-name = "vccio_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-name = "vcc3v3_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_1v8: LDO_REG7 {
+				regulator-name = "vcca_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG8 {
+				regulator-name = "vcca1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_image: LDO_REG9 {
+				regulator-name = "vcca1v8_image";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_3v3: SWITCH_REG1 {
+				regulator-boot-on;
+				regulator-name = "vcc_3v3";
+			};
+
+			vcc3v3_sd: SWITCH_REG2 {
+				regulator-name = "vcc3v3_sd";
+			};
+		};
+	};
+};
+
+/* i2c2_m1 exposed on csi port, pulled up to vcc_3v3 */
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2m1_xfer>;
+	status = "okay";
+};
+
+/* i2c3_m1 exposed on dsi port, pulled up to vcc_3v3 */
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3m1_xfer>;
+	status = "okay";
+};
+
+/*
+ * i2c4_m0 is exposed on PI40, pulled up to vcc_3v3
+ * pin 27 - i2c4_sda_m0
+ * pin 28 - i2c4_scl_m0
+ */
+&i2c4 {
+	status = "okay";
+};
+
+/*
+ * i2c5_m0 is exposed on PI40
+ * pin 29 - i2c5_scl_m0
+ * pin 31 - i2c5_sda_m0
+ */
+&i2c5 {
+	status = "disabled";
+};
+
+&i2s0_8ch {
+	status = "okay";
+};
+
+&i2s1_8ch {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s1m0_sclktx
+		     &i2s1m0_lrcktx
+		     &i2s1m0_sdi0
+		     &i2s1m0_sdo0>;
+	rockchip,trcm-sync-tx-only;
+	status = "okay";
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x1>;
+	};
+};
+
+&pcie2x1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_reset_h>;
+	reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie_p>;
+	status = "okay";
+};
+
+&pinctrl {
+	bt {
+		bt_enable_h: bt-enable-h {
+			rockchip,pins = <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_host_wake_l: bt-host-wake-l {
+			rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		bt_wake_l: bt-wake-l {
+			rockchip,pins = <0 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	leds {
+		user_led_enable_h: user-led-enable-h {
+			rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		pcie_enable_h: pcie-enable-h {
+			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		pcie_reset_h: pcie-reset-h {
+			rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic_int {
+			rockchip,pins =
+				<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb {
+		vcc5v0_usb30_host_en_h: vcc5v0-usb30-host-en_h {
+			rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		vcc5v0_usb_otg_en_h: vcc5v0-usb-otg-en_h {
+			rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	status = "okay";
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcca1v8_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio2-supply = <&vcc_1v8>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcca1v8_pmu>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc_3v3>;
+	vccio7-supply = <&vcc_3v3>;
+};
+
+&saradc {
+	vref-supply = <&vcca_1v8>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	sd-uhs-sdr50;
+	vmmc-supply = <&vcc3v3_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
+	vmmc-supply = <&vcc3v3_sys>;
+	vqmmc-supply = <&vcca1v8_pmu>;
+	status = "okay";
+};
+
+&sfc {
+	pinctrl-0 = <&fspi_pins>;
+	pinctrl-names = "default";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
+	};
+};
+
+&tsadc {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
+	status = "okay";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm4345c5";
+		clocks = <&rk809 1>;
+		clock-names = "lpo";
+		device-wakeup-gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio0 RK_PC1 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+		vbat-supply = <&vcc3v3_sys>;
+		vddio-supply = <&vcca1v8_pmu>;
+	};
+};
+
+/*
+ * uart2_m0 is exposed on PI40
+ * pin 8  - uart2_tx_m0
+ * pin 10 - uart2_rx_m0
+ */
+&uart2 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb30_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb_otg>;
+	status = "okay";
+};
+
+&usb2phy1_otg {
+	phy-supply = <&vcc5v0_usb30_host>;
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy1 {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	status = "okay";
+};
+
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
board/pine64/quartz64_rk3566/MAINTAINERS +3 -0
index dbc0dfbd9787..2e637bf51ba3 100644
@@ -5,5 +5,8 @@ S:	Maintained
  F:	board/pine64/quartz64_rk3566/
  F:	include/configs/quartz64_rk3566.h
  F:	configs/quartz64-a-rk3566_defconfig
+F:	configs/quartz64-b-rk3566_defconfig
  F:	arch/arm/dts/rk3566-quartz64-a.dts
  F:	arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
+F:	arch/arm/dts/rk3566-quartz64-b.dts
+F:	arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi
configs/quartz64-b-rk3566_defconfig new file +106 -0
new file mode 100644
index 000000000000..b98c81f9dcef
@@ -0,0 +1,106 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TEXT_BASE=0x00a00000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
+CONFIG_SF_DEFAULT_SPEED=24000000
+CONFIG_SF_DEFAULT_MODE=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="rk3566-quartz64-b"
+CONFIG_ROCKCHIP_RK3568=y
+CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
+CONFIG_ROCKCHIP_SPI_IMAGE=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_TARGET_QUARTZ64_RK3566=y
+CONFIG_SPL_STACK=0x400000
+CONFIG_DEBUG_UART_BASE=0xFE660000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SPL_SPI_FLASH_SUPPORT=y
+CONFIG_SPL_SPI=y
+CONFIG_SYS_LOAD_ADDR=0xc00800
+CONFIG_PCI=y
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_FIT_SIGNATURE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-quartz64-b.dtb"
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_MAX_SIZE=0x40000
+CONFIG_SPL_PAD_TO=0x7f8000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x4000000
+CONFIG_SPL_BSS_MAX_SIZE=0x4000
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_SPI_LOAD=y
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000
+CONFIG_SPL_ATF=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIVE=y
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_SYSCON=y
+CONFIG_SCSI_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_SPL_CLK=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
+CONFIG_SUPPORT_EMMC_RPMB=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_ROCKCHIP=y
+CONFIG_SF_DEFAULT_BUS=4
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_GIGADEVICE=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_NVME_PCI=y
+CONFIG_PCIE_DW_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_SPL_RAM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_BAUDRATE=1500000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_ROCKCHIP_SFC=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_GENERIC=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_ERRNO_STR=y
doc/board/rockchip/rockchip.rst +1 -0
index c7d4c835db80..1c0e10c40607 100644
@@ -97,6 +97,7 @@ List of mainline supported Rockchip boards:
       - Rockchip Evb-RK3568 (evb-rk3568)
       - Hardkernel ODROID-M1 (odroid-m1-rk3568)
       - Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig)
+     - Pine64 Quartz64-B Board (quartz64-b-rk3566_defconfig)
 
  * rk3588
       - Rockchip EVB (evb-rk3588)
#15 lore raw

PATCH 3/5 board: rockchip: Add Pine64 SOQuartz on Model A

In reply to Jonas Karlman

The Pine64 SOQuartz Model A board is a carrier board for the SOQuartz CM4-compatible compute module. It exposes PCIe, ethernet, USB, HDMI, CSI, DSI, eDP and a 40 pin GPIO header, and is powered by 12V DC.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Device tree is imported from linux v6.4.

---
 arch/arm/dts/Makefile                         |   1 +
 .../dts/rk3566-soquartz-model-a-u-boot.dtsi   |   3 +
 arch/arm/dts/rk3566-soquartz-model-a.dts      | 232 ++++++
 arch/arm/dts/rk3566-soquartz-u-boot.dtsi      |  30 +
 arch/arm/dts/rk3566-soquartz.dtsi             | 688 ++++++++++++++++++
 board/pine64/quartz64_rk3566/MAINTAINERS      |   5 +
 configs/soquartz-model-a-rk3566_defconfig     |  90 +++
 doc/board/rockchip/rockchip.rst               |   1 +
 8 files changed, 1050 insertions(+)
 create mode 100644 arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
 create mode 100644 arch/arm/dts/rk3566-soquartz-model-a.dts
 create mode 100644 arch/arm/dts/rk3566-soquartz-u-boot.dtsi
 create mode 100644 arch/arm/dts/rk3566-soquartz.dtsi
 create mode 100644 configs/soquartz-model-a-rk3566_defconfig
arch/arm/dts/Makefile +1 -0
index 3cc921e5cc1e..aca2ec44a888 100644
@@ -170,6 +170,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \
 	rk3566-quartz64-a.dtb \
 	rk3566-quartz64-b.dtb \
 	rk3566-radxa-cm3-io.dtb \
+	rk3566-soquartz-model-a.dtb \
 	rk3568-evb.dtb \
 	rk3568-odroid-m1.dtb \
 	rk3568-rock-3a.dtb
arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi new file +3 -0
new file mode 100644
index 000000000000..0e662eafa4c7
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk3566-soquartz-u-boot.dtsi"
arch/arm/dts/rk3566-soquartz-model-a.dts new file +232 -0

232 lines not on this page · raw message

arch/arm/dts/rk3566-soquartz-u-boot.dtsi new file +30 -0
new file mode 100644
index 000000000000..29aae242b07b
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk356x-u-boot.dtsi"
+
+/ {
+	chosen {
+		stdout-path = &uart2;
+	};
+};
+
+&pcie2x1 {
+	pinctrl-0 = <&pcie20m2_pins &pcie_reset_h>;
+};
+
+&sdhci {
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+};
+
+&uart2 {
+	bootph-all;
+	clock-frequency = <24000000>;
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	dr_mode = "host";
+};
arch/arm/dts/rk3566-soquartz.dtsi new file +688 -0

688 lines not on this page · raw message

board/pine64/quartz64_rk3566/MAINTAINERS +5 -0
index 2e637bf51ba3..748ff5033d93 100644
@@ -6,7 +6,12 @@ F:	board/pine64/quartz64_rk3566/
 F:	include/configs/quartz64_rk3566.h
 F:	configs/quartz64-a-rk3566_defconfig
 F:	configs/quartz64-b-rk3566_defconfig
+F:	configs/soquartz-model-a-rk3566_defconfig
 F:	arch/arm/dts/rk3566-quartz64-a.dts
 F:	arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
 F:	arch/arm/dts/rk3566-quartz64-b.dts
 F:	arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi
+F:	arch/arm/dts/rk3566-soquartz.dtsi
+F:	arch/arm/dts/rk3566-soquartz-u-boot.dtsi
+F:	arch/arm/dts/rk3566-soquartz-model-a.dts
+F:	arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
configs/soquartz-model-a-rk3566_defconfig new file +90 -0

90 lines not on this page · raw message

doc/board/rockchip/rockchip.rst +1 -0
index 1c0e10c40607..a17bcb2afc1a 100644
@@ -98,6 +98,7 @@ List of mainline supported Rockchip boards:
      - Hardkernel ODROID-M1 (odroid-m1-rk3568)
      - Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig)
      - Pine64 Quartz64-B Board (quartz64-b-rk3566_defconfig)
+     - Pine64 SOQuartz on Model A (soquartz-model-a-rk3566_defconfig)
 
 * rk3588
      - Rockchip EVB (evb-rk3588)
Signature · 1 line
2.41.0
#16 lore raw

Re: [PATCH 3/5] board: rockchip: Add Pine64 SOQuartz on Model A

Quoted 10 lines · Jonas Karlman

The Pine64 SOQuartz Model A board is a carrier board for the SOQuartz CM4-compatible compute module. It exposes PCIe, ethernet, USB, HDMI, CSI, DSI, eDP and a 40 pin GPIO header, and is powered by 12V DC.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Quoted 6 lines

Device tree is imported from linux v6.4.

---

[...]

Boot log with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf:
DDR V1.17 992b933606 typ 23/04/25-10:10:19
ln
LP4/4x derate en, other dram:1x trefi
ddrconfig:0
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS=1 Die BW=16 Size=4096MB
tdqss: cs0 dqs0: 24ps, dqs1: -48ps, dqs2: -24ps, dqs3: -48ps,

change to: 324MHz
clk skew:0x60

change to: 528MHz
clk skew:0x58

change to: 780MHz
clk skew:0x58

change to: 1056MHz(final freq)
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:22%
dram drv:40,odt:80
vref_ca:00000071
clk skew:0x29
cs 0:
the read training result:
DQS0:0x3a, DQS1:0x3f, DQS2:0x3c, DQS3:0x39,

min  : 0x9  0x8  0x3  0x1  0x2  0x3  0x7  0x6 , 0x7  0x1  0x2  0x2  0x7  0xf 0x10  0xc ,
       0x7  0x6  0x6  0x6  0x5  0x1  0x5  0x4 , 0x1  0x2  0x7  0x2  0x7  0x6  0x6  0x4 ,
mid  :0x27 0x27 0x22 0x1e 0x20 0x21 0x25 0x25 ,0x25 0x22 0x22 0x22 0x26 0x2e 0x2f 0x2b ,
      0x27 0x26 0x25 0x24 0x23 0x20 0x24 0x23 ,0x20 0x21 0x25 0x21 0x26 0x24 0x24 0x22 ,
max  :0x46 0x47 0x41 0x3b 0x3f 0x40 0x44 0x45 ,0x44 0x43 0x42 0x43 0x46 0x4e 0x4e 0x4b ,
      0x47 0x46 0x45 0x43 0x42 0x40 0x44 0x43 ,0x40 0x40 0x44 0x40 0x45 0x42 0x42 0x40 ,
range:0x3d 0x3f 0x3e 0x3a 0x3d 0x3d 0x3d 0x3f ,0x3d 0x42 0x40 0x41 0x3f 0x3f 0x3e 0x3f ,
      0x40 0x40 0x3f 0x3d 0x3d 0x3f 0x3f 0x3f ,0x3f 0x3e 0x3d 0x3e 0x3e 0x3c 0x3c 0x3c ,
the write training result:
DQS0:0x2c, DQS1:0x23, DQS2:0x26, DQS3:0x23,
min  :0x52 0x55 0x50 0x4d 0x4d 0x4e 0x53 0x54 0x54 ,0x43 0x3f 0x3f 0x41 0x46 0x4c 0x4c 0x4a 0x45 ,
      0x4a 0x4a 0x49 0x49 0x48 0x45 0x48 0x49 0x49 ,0x42 0x43 0x48 0x45 0x48 0x47 0x45 0x46 0x47 ,
mid  :0x6f 0x72 0x6c 0x69 0x69 0x6a 0x6f 0x6f 0x70 ,0x5f 0x5c 0x5b 0x5d 0x62 0x69 0x68 0x66 0x61 ,
      0x67 0x67 0x66 0x66 0x64 0x61 0x63 0x65 0x66 ,0x5f 0x5f 0x65 0x61 0x65 0x64 0x61 0x63 0x64 ,
max  :0x8c 0x8f 0x89 0x85 0x86 0x87 0x8c 0x8b 0x8d ,0x7c 0x7a 0x77 0x79 0x7e 0x86 0x84 0x83 0x7d ,
      0x85 0x84 0x83 0x83 0x80 0x7d 0x7f 0x82 0x83 ,0x7c 0x7c 0x83 0x7d 0x83 0x81 0x7e 0x80 0x81 ,
range:0x3a 0x3a 0x39 0x38 0x39 0x39 0x39 0x37 0x39 ,0x39 0x3b 0x38 0x38 0x38 0x3a 0x38 0x39 0x38 ,
      0x3b 0x3a 0x3a 0x3a 0x38 0x38 0x37 0x39 0x3a ,0x3a 0x39 0x3b 0x38 0x3b 0x3a 0x39 0x3a 0x3a ,
CA Training result:
cs:0 min  :0x3c 0x3a 0x36 0x37 0x38 0x30 0x38 ,0x3f 0x38 0x39 0x35 0x38 0x32 0x3a ,
cs:0 mid  :0x7a 0x7c 0x73 0x77 0x75 0x71 0x67 ,0x7b 0x78 0x77 0x76 0x77 0x73 0x69 ,
cs:0 max  :0xb8 0xbe 0xb1 0xb7 0xb3 0xb3 0x97 ,0xb7 0xb9 0xb5 0xb7 0xb6 0xb4 0x98 ,

cs:0 range:0x7c 0x84 0x7b 0x80 0x7b 0x83 0x5f ,0x78 0x81 0x7c 0x82 0x7e 0x82 0x5e , out

U-Boot SPL 2023.07 (Jul 23 2023 - 13:07:31 +0000) rockchip_sdhci_probe clk set rate fail! Trying to boot from MMC2
## Checking hash(es) for config config-1 ... OK ## Checking hash(es) for Image atf-1 ... sha256+ OK ## Checking hash(es) for Image u-boot ... sha256+ OK ## Checking hash(es) for Image fdt-1 ... sha256+ OK ## Checking hash(es) for Image atf-2 ... sha256+ OK ## Checking hash(es) for Image atf-3 ... sha256+ OK ## Checking hash(es) for Image atf-4 ... sha256+ OK ## Checking hash(es) for Image atf-5 ... sha256+ OK ## Checking hash(es) for Image atf-6 ... sha256+ OK

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-607-gbf602aff1:cl
NOTICE:  BL31: Built : 10:16:03, Jun  5 2023
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    pmu v1 is valid 220114
INFO:    dfs DDR fsp_param[0].freq_mhz= 1056MHz
INFO:    dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO:    dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO:    dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0xa00000
INFO:    SPSR = 0x3c9

U-Boot 2023.07 (Jul 23 2023 - 13:07:31 +0000)

Model: PINE64 RK3566 SOQuartz on Model A carrier board
DRAM:  4 GiB (effective 3.7 GiB)
PMIC:  RK8090 (on=0x40, off=0x00)
Core:  315 devices, 27 uclasses, devicetree: separate
MMC:   rockchip_sdhci_probe clk set rate fail!
mmc@fe2b0000: 1, mmc@fe2c0000: 2, mmc@fe310000: 0
Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: PINE64 RK3566 SOQuartz on Model A carrier board
Net:   No ethernet found.

Hit any key to stop autoboot: 0
=>

Regards,
Jonas

Reviewed-by on v1 3/5
#17 lore raw

Re: [PATCH 3/5] board: rockchip: Add Pine64 SOQuartz on Model A

In reply to Jonas Karlman
Quoted 10 lines · Jonas Karlman

The Pine64 SOQuartz Model A board is a carrier board for the SOQuartz CM4-compatible compute module. It exposes PCIe, ethernet, USB, HDMI, CSI, DSI, eDP and a 40 pin GPIO header, and is powered by 12V DC.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Quoted 5 lines

Device tree is imported from linux v6.4.

Thanks,
- Kever

Quoted 1,130 lines
---
  arch/arm/dts/Makefile                         |   1 +
  .../dts/rk3566-soquartz-model-a-u-boot.dtsi   |   3 +
  arch/arm/dts/rk3566-soquartz-model-a.dts      | 232 ++++++
  arch/arm/dts/rk3566-soquartz-u-boot.dtsi      |  30 +
  arch/arm/dts/rk3566-soquartz.dtsi             | 688 ++++++++++++++++++
  board/pine64/quartz64_rk3566/MAINTAINERS      |   5 +
  configs/soquartz-model-a-rk3566_defconfig     |  90 +++
  doc/board/rockchip/rockchip.rst               |   1 +
  8 files changed, 1050 insertions(+)

create mode 100644 arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-soquartz-model-a.dts create mode 100644 arch/arm/dts/rk3566-soquartz-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-soquartz.dtsi create mode 100644 configs/soquartz-model-a-rk3566_defconfig

arch/arm/dts/Makefile +1 -0
index 3cc921e5cc1e..aca2ec44a888 100644
@@ -170,6 +170,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \
  	rk3566-quartz64-a.dtb \
  	rk3566-quartz64-b.dtb \
  	rk3566-radxa-cm3-io.dtb \
+	rk3566-soquartz-model-a.dtb \
  	rk3568-evb.dtb \
  	rk3568-odroid-m1.dtb \
  	rk3568-rock-3a.dtb
arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi new file +3 -0
new file mode 100644
index 000000000000..0e662eafa4c7
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk3566-soquartz-u-boot.dtsi"
arch/arm/dts/rk3566-soquartz-model-a.dts new file +232 -0
new file mode 100644
index 000000000000..2208dbfb7f0a
@@ -0,0 +1,232 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-soquartz.dtsi"
+
+/ {
+	model = "PINE64 RK3566 SOQuartz on Model A carrier board";
+	compatible = "pine64,soquartz-model-a", "pine64,soquartz", "rockchip,rk3566";
+
+	/* labeled DCIN_12V in schematic */
+	vcc12v_dcin: vcc12v-dcin-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	vcc5v0_usb: vcc5v0-usb-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	/*
+	 * Labelled VCC3V0_SD in schematic to not conflict with PMIC
+	 * regulator, it's 3.3v in actuality
+	 */
+	vcc3v0_sd: vcc3v0-sd-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v0_sd";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	vcc3v3_pcie: vcc3v3-pcie-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_pcie";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc12v_pcie: vcc12v-pcie-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_pcie";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+};
+
+/* phy for pcie */
+&combphy2 {
+	phy-supply = <&vcc3v3_sys>;
+	status = "okay";
+};
+
+&gmac1 {
+	status = "okay";
+};
+
+/*
+ * i2c1 is exposed on CM1 / Module1A
+ * pin 80 - SCL0 - i2c1_scl_m0, pullup to vcc3v3_pmu
+ * pin 82 - SDA0 - i2c1_sda_m0, pullup to vcc3v3_pmu
+ */
+&i2c1 {
+	status = "okay";
+
+	/*
+	 * the rtc interrupt is tied to PMIC_PWRON,
+	 * it will force reset the board if triggered.
+	 */
+	pcf85063: rtc@51 {
+		compatible = "nxp,pcf85063";
+		reg = <0x51>;
+	};
+};
+
+/*
+ * i2c2 is exposed on CM1 / Module1A - to PI40
+ * pin 56 - GPIO3 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch
+ * pin 58 - GPIO2 - i2c2_sda_m1, pullup to vcc_3v3
+ */
+&i2c2 {
+	status = "disabled";
+};
+
+/*
+ * i2c3 is exposed on CM1 / Module1A - to PI40
+ * pin 35 - ID_SC(GPIO28) - i2c3_scl_m0, pullup to vcc_3v3
+ * pin 36 - ID_SD(GPIO27) - i2c3_sda_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+	status = "disabled";
+};
+
+/*
+ * i2c4 is exposed on CM2 / Module1B - to PI40
+ * pin 45 - GPIO24 - i2c4_scl_m1
+ * pin 47 - GPIO23 - i2c4_sda_m1
+ */
+&i2c4 {
+	status = "disabled";
+};
+
+/*
+ * i2s1_8ch is exposed on CM1 / Module1A - to PI40
+ * pin 24 - GPIO26 - i2s1_sdi1_m1
+ * pin 25 - GPIO21 - i2s1_sdo0_m1
+ * pin 26 - GPIO19 - i2s1_lrck_tx_m1
+ * pin 27 - GPIO20 - i2s1_sdi0_m1
+ * pin 29 - GPIO16 - i2s1_sdi3_m1
+ * pin 30 - GPIO6  - i2s1_sdi2_m1
+ * pin 40 - GPIO9  - i2s1_sdo1_m1, shared with spi3
+ * pin 41 - GPIO25 - i2s1_sdo2_m1
+ * pin 49 - GPIO18 - i2s1_sclk_tx_m1
+ * pin 50 - GPIO17 - i2s1_mclk_m1
+ * pin 56 - GPIO3  - i2s1_sdo3_m1, shared with i2c2
+ */
+&i2s1_8ch {
+	status = "disabled";
+};
+
+&led_diy {
+	status = "okay";
+};
+
+&led_work {
+	status = "okay";
+};
+
+&pcie2x1 {
+	vpcie3v3-supply = <&vcc3v3_pcie>;
+	status = "okay";
+};
+
+&rgmii_phy1 {
+	status = "okay";
+};
+
+&rgmii_phy1 {
+	status = "okay";
+};
+
+/*
+ * saradc is exposed on CM1 / Module1A - to J2
+ * pin 94 - AIN1 - saradc_vin3
+ * pin 96 - AIN0 - saradc_vin2
+ */
+&saradc {
+	status = "disabled";
+};
+
+/*
+ * vmmc-supply is vcc3v3_sd on v1.0 and vcc3v0_sd on v1.1+
+ * the soquartz SoM has SDMMC_PWR (CM1 pin 75) hardwired to vcc3v3_sys,
+ * so we use vcc3v3_sd here to ensure the regulator is enabled on older boards.
+ */
+&sdmmc0 {
+	vmmc-supply = <&vcc3v3_sd>;
+	status = "okay";
+};
+
+/*
+ * spi3 is exposed on CM1 / Module1A - to PI40
+ * pin 37 - GPIO7  - spi3_cs1_m0
+ * pin 38 - GPIO11 - spi3_clk_m0
+ * pin 39 - GPIO8  - spi3_cs0_m0
+ * pin 40 - GPIO9  - spi3_miso_m0, shared with i2s1_8ch
+ * pin 44 - GPIO10 - spi3_mosi_m0
+ */
+&spi3 {
+	status = "disabled";
+};
+
+/*
+ * uart2 is exposed on CM1 / Module1A - to PI40
+ * pin 51 - GPIO15 - uart2_rx_m0
+ * pin 55 - GPIO14 - uart2_tx_m0
+ */
+&uart2 {
+	status = "okay";
+};
+
+/*
+ * uart7 is exposed on CM1 / Module1A - to PI40
+ * pin 46 - GPIO22 - uart7_tx_m2
+ * pin 47 - GPIO23 - uart7_rx_m2
+ */
+&uart7 {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb>;
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	status = "okay";
+};
+
+&vbus {
+	vin-supply = <&vcc5v0_usb>;
+};
+
+&vcc3v3_sd {
+	regulator-always-on;
+	regulator-boot-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	status = "okay";
+};
arch/arm/dts/rk3566-soquartz-u-boot.dtsi new file +30 -0
new file mode 100644
index 000000000000..29aae242b07b
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk356x-u-boot.dtsi"
+
+/ {
+	chosen {
+		stdout-path = &uart2;
+	};
+};
+
+&pcie2x1 {
+	pinctrl-0 = <&pcie20m2_pins &pcie_reset_h>;
+};
+
+&sdhci {
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+};
+
+&uart2 {
+	bootph-all;
+	clock-frequency = <24000000>;
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	dr_mode = "host";
+};
arch/arm/dts/rk3566-soquartz.dtsi new file +688 -0
new file mode 100644
index 000000000000..31aa2b8efe39
@@ -0,0 +1,688 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+	model = "Pine64 RK3566 SoQuartz SOM";
+	compatible = "pine64,soquartz", "rockchip,rk3566";
+
+	aliases {
+		ethernet0 = &gmac1;
+		mmc0 = &sdmmc0;
+		mmc1 = &sdhci;
+		mmc2 = &sdmmc1;
+	};
+
+	chosen: chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	gmac1_clkin: external-gmac1-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac1_clkin";
+		#clock-cells = <0>;
+	};
+
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_diy: led-diy {
+			label = "diy-led";
+			default-state = "on";
+			gpios = <&gpio0 RK_PC1 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			pinctrl-names = "default";
+			pinctrl-0 = <&diy_led_enable_h>;
+			retain-state-suspended;
+			status = "disabled";
+		};
+
+		led_work: led-work {
+			label = "work-led";
+			default-state = "off";
+			gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&work_led_enable_h>;
+			retain-state-suspended;
+			status = "disabled";
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		status = "okay";
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk809 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+		reset-gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_LOW>;
+	};
+
+	vbus: vbus-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	/* sourced from vbus, vbus is provided by the carrier board */
+	vcc5v0_sys: vcc5v0-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vbus>;
+	};
+
+	vcc3v3_sys: vcc3v3-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>, <&gmac1_clkin>;
+	clock_in_out = "input";
+	phy-supply = <&vcc_3v3>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m0_miim
+		     &gmac1m0_tx_bus2
+		     &gmac1m0_rx_bus2
+		     &gmac1m0_rgmii_clk
+		     &gmac1m0_clkinout
+		     &gmac1m0_rgmii_bus>;
+	snps,reset-gpio = <&gpio0 RK_PC3 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	/* Reset time is 20ms, 100ms for rtl8211f, also works well here */
+	snps,reset-delays-us = <0 20000 100000>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	phy-handle = <&rgmii_phy1>;
+	status = "disabled";
+};
+
+&gpio0 {
+	nextrst-hog {
+		gpio-hog;
+		/*
+		 * GPIO_ACTIVE_LOW + output-low here means that the pin is set
+		 * to high, because output-low decides the value pre-inversion.
+		 */
+		gpios = <RK_PA5 GPIO_ACTIVE_LOW>;
+		line-name = "nEXTRST";
+		output-low;
+	};
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vdda0v9_image>;
+	avdd-1v8-supply = <&vcca1v8_image>;
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	vdd_cpu: regulator@1c {
+		compatible = "tcs,tcs4525";
+		reg = <0x1c>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <2300>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "rk808-clkout1", "rk808-clkout2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc5-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+					regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vcc_ddr";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_npu: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vdd_npu";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG5 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdda0v9_image: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdda0v9_image";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdda_0v9";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdda0v9_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_acodec";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_1v8: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca_1v8";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca1v8_pmu";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_image: LDO_REG9 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca1v8_image";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v3: SWITCH_REG1 {
+				regulator-name = "vcc_3v3";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_sd: SWITCH_REG2 {
+				regulator-name = "vcc3v3_sd";
+				status = "disabled";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+		};
+	};
+};
+
+/*
+ * i2c1 is exposed on CM1 / Module1A
+ * pin 80 - i2c1_scl_m0, pullup to vcc3v3_pmu
+ * pin 82 - i2c1_sda_m0, pullup to vcc3v3_pmu
+ */
+&i2c1 {
+	status = "disabled";
+};
+
+/*
+ * i2c2 is exposed on CM1 / Module1A
+ * pin 56 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch
+ * pin 58 - i2c2_sda_m1, pullup to vcc_3v3
+ */
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2m1_xfer>;
+	status = "disabled";
+};
+
+/*
+ * i2c3 is exposed on CM1 / Module1A
+ * pin 35 - i2c3_scl_m0, pullup to vcc_3v3
+ * pin 36 - i2c3_sda_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+	status = "disabled";
+};
+
+/*
+ * i2c4 is exposed on CM2 / Module1B
+ * pin 45 - i2c4_scl_m1
+ * pin 47 - i2c4_sda_m1
+ */
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4m1_xfer>;
+	status = "disabled";
+};
+
+&i2s0_8ch {
+	status = "okay";
+};
+
+/*
+ * i2s1_8ch is exposed on CM1 / Module1A
+ * pin 24 - i2s1_sdi1_m1
+ * pin 25 - i2s1_sdo0_m1
+ * pin 26 - i2s1_lrck_tx_m1
+ * pin 27 - i2s1_sdi0_m1
+ * pin 29 - i2s1_sdi3_m1
+ * pin 30 - i2s1_sdi2_m1
+ * pin 40 - i2s1_sdo1_m1, shared with spi3
+ * pin 41 - i2s1_sdo2_m1
+ * pin 49 - i2s1_sclk_tx_m1
+ * pin 50 - i2s1_mclk_m1
+ * pin 56 - i2s1_sdo3_m1, shared with i2c2
+ */
+&i2s1_8ch {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s1m1_sclktx &i2s1m1_sclkrx
+		     &i2s1m1_lrcktx &i2s1m1_lrckrx
+		     &i2s1m1_sdi0   &i2s1m1_sdi1
+		     &i2s1m1_sdi2   &i2s1m1_sdi3
+		     &i2s1m1_sdo0   &i2s1m1_sdo1
+		     &i2s1m1_sdo2   &i2s1m1_sdo3>;
+	status = "disabled";
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+		status = "disabled";
+	};
+};
+
+&pcie2x1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_reset_h>;
+	reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
+};
+
+&pinctrl {
+	bt {
+		bt_enable_h: bt-enable-h {
+			rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_host_wake_l: bt-host-wake-l {
+			rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		bt_wake_l: bt-wake-l {
+			rockchip,pins = <2 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	leds {
+		work_led_enable_h: work-led-enable-h {
+			rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		diy_led_enable_h: diy-led-enable-h {
+			rockchip,pins = <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		pcie_clkreq_h: pcie-clkreq-h {
+			rockchip,pins = <1 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+		pcie_reset_h: pcie-reset-h {
+			rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcc3v3_pmu>;
+	vccio1-supply = <&vcc_3v3>;
+	vccio2-supply = <&vcc_1v8>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_1v8>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc_3v3>;
+	vccio7-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+/*
+ * saradc is exposed on CM1 / Module1A
+ * pin 94 - saradc_vin3
+ * pin 96 - saradc_vin2
+ */
+&saradc {
+	vref-supply = <&vcca_1v8>;
+	status = "disabled";
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdmmc0 {
+	broken-cd;
+	bus-width = <4>;
+	cap-sd-highspeed;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "disabled";
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
+	sd-uhs-sdr50;
+	vmmc-supply = <&vcc3v3_sys>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+/*
+ * spi3 is exposed on CM1 / Module1A
+ * pin 37 - spi3_cs1_m0
+ * pin 38 - spi3_clk_m0
+ * pin 39 - spi3_cs0_m0
+ * pin 40 - spi3_miso_m0, shared with i2s1_8ch
+ * pin 44 - spi3_mosi_m0
+ */
+&spi3 {
+	status = "disabled";
+};
+
+&tsadc {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rk809 1>;
+		clock-names = "lpo";
+		device-wakeup-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+		vbat-supply = <&vcc3v3_sys>;
+		vddio-supply = <&vcca1v8_pmu>;
+	};
+};
+
+/*
+ * uart2 is exposed on CM1 / Module1A
+ * pin 51 - uart2_rx_m0
+ * pin 55 - uart2_tx_m0
+ */
+&uart2 {
+	status = "disabled";
+};
+
+/*
+ * uart7 is exposed on CM1 / Module1A
+ * pin 46 - uart7_tx_m2
+ * pin 47 - uart7_rx_m2
+ */
+&uart7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart7m2_xfer>;
+	status = "disabled";
+};
+
+/* dwc3_otg is the only usb port available */
+&usb2phy0 {
+	status = "disabled";
+};
+
+&usb2phy0_otg {
+	status = "disabled";
+};
+
+&usb_host0_xhci {
+	status = "disabled";
+};
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
board/pine64/quartz64_rk3566/MAINTAINERS +5 -0
index 2e637bf51ba3..748ff5033d93 100644
@@ -6,7 +6,12 @@ F:	board/pine64/quartz64_rk3566/
  F:	include/configs/quartz64_rk3566.h
  F:	configs/quartz64-a-rk3566_defconfig
  F:	configs/quartz64-b-rk3566_defconfig
+F:	configs/soquartz-model-a-rk3566_defconfig
  F:	arch/arm/dts/rk3566-quartz64-a.dts
  F:	arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
  F:	arch/arm/dts/rk3566-quartz64-b.dts
  F:	arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi
+F:	arch/arm/dts/rk3566-soquartz.dtsi
+F:	arch/arm/dts/rk3566-soquartz-u-boot.dtsi
+F:	arch/arm/dts/rk3566-soquartz-model-a.dts
+F:	arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
configs/soquartz-model-a-rk3566_defconfig new file +90 -0
new file mode 100644
index 000000000000..c3958579db73
@@ -0,0 +1,90 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TEXT_BASE=0x00a00000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
+CONFIG_DEFAULT_DEVICE_TREE="rk3566-soquartz-model-a"
+CONFIG_ROCKCHIP_RK3568=y
+CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_TARGET_QUARTZ64_RK3566=y
+CONFIG_SPL_STACK=0x400000
+CONFIG_DEBUG_UART_BASE=0xFE660000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SYS_LOAD_ADDR=0xc00800
+CONFIG_PCI=y
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_FIT_SIGNATURE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-soquartz-model-a.dtb"
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_MAX_SIZE=0x40000
+CONFIG_SPL_PAD_TO=0x7f8000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x4000000
+CONFIG_SPL_BSS_MAX_SIZE=0x4000
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_ATF=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIVE=y
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_SYSCON=y
+CONFIG_SCSI_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_SPL_CLK=y
+CONFIG_GPIO_HOG=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
+CONFIG_SUPPORT_EMMC_RPMB=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_ROCKCHIP=y
+CONFIG_NVME_PCI=y
+CONFIG_PCIE_DW_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_SPL_RAM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_BAUDRATE=1500000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_ERRNO_STR=y
doc/board/rockchip/rockchip.rst +1 -0
index 1c0e10c40607..a17bcb2afc1a 100644
@@ -98,6 +98,7 @@ List of mainline supported Rockchip boards:
       - Hardkernel ODROID-M1 (odroid-m1-rk3568)
       - Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig)
       - Pine64 Quartz64-B Board (quartz64-b-rk3566_defconfig)
+     - Pine64 SOQuartz on Model A (soquartz-model-a-rk3566_defconfig)
 
  * rk3588
       - Rockchip EVB (evb-rk3588)
#18 lore raw

PATCH 4/5 board: rockchip: Add Pine64 SOQuartz on Blade

In reply to Jonas Karlman

The Pine64 SOQuartz Blade board is a carrier board for the SOQuartz CM4-compatible compute module. It features PoE, an M.2 slot, an SD card slot, HDMI, USB, serial and ethernet.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe
- USB host

Device tree is imported from linux v6.4.

---
 arch/arm/dts/Makefile                         |   1 +
 .../arm/dts/rk3566-soquartz-blade-u-boot.dtsi |   3 +
 arch/arm/dts/rk3566-soquartz-blade.dts        | 194 ++++++++++++++++++
 board/pine64/quartz64_rk3566/MAINTAINERS      |   3 +
 configs/soquartz-blade-rk3566_defconfig       |  90 ++++++++
 doc/board/rockchip/rockchip.rst               |   1 +
 6 files changed, 292 insertions(+)
 create mode 100644 arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi
 create mode 100644 arch/arm/dts/rk3566-soquartz-blade.dts
 create mode 100644 configs/soquartz-blade-rk3566_defconfig
arch/arm/dts/Makefile +1 -0
index aca2ec44a888..7a41675ef89d 100644
@@ -170,6 +170,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \
 	rk3566-quartz64-a.dtb \
 	rk3566-quartz64-b.dtb \
 	rk3566-radxa-cm3-io.dtb \
+	rk3566-soquartz-blade.dtb \
 	rk3566-soquartz-model-a.dtb \
 	rk3568-evb.dtb \
 	rk3568-odroid-m1.dtb \
arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi new file +3 -0
new file mode 100644
index 000000000000..0e662eafa4c7
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk3566-soquartz-u-boot.dtsi"
arch/arm/dts/rk3566-soquartz-blade.dts new file +194 -0

194 lines not on this page · raw message

board/pine64/quartz64_rk3566/MAINTAINERS +3 -0
index 748ff5033d93..603d2ee9d5e9 100644
@@ -6,6 +6,7 @@ F:	board/pine64/quartz64_rk3566/
 F:	include/configs/quartz64_rk3566.h
 F:	configs/quartz64-a-rk3566_defconfig
 F:	configs/quartz64-b-rk3566_defconfig
+F:	configs/soquartz-blade-rk3566_defconfig
 F:	configs/soquartz-model-a-rk3566_defconfig
 F:	arch/arm/dts/rk3566-quartz64-a.dts
 F:	arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
@@ -13,5 +14,7 @@ F:	arch/arm/dts/rk3566-quartz64-b.dts
 F:	arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi
 F:	arch/arm/dts/rk3566-soquartz.dtsi
 F:	arch/arm/dts/rk3566-soquartz-u-boot.dtsi
+F:	arch/arm/dts/rk3566-soquartz-blade.dts
+F:	arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi
 F:	arch/arm/dts/rk3566-soquartz-model-a.dts
 F:	arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
configs/soquartz-blade-rk3566_defconfig new file +90 -0

90 lines not on this page · raw message

doc/board/rockchip/rockchip.rst +1 -0
index a17bcb2afc1a..254a68b43eaf 100644
@@ -98,6 +98,7 @@ List of mainline supported Rockchip boards:
      - Hardkernel ODROID-M1 (odroid-m1-rk3568)
      - Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig)
      - Pine64 Quartz64-B Board (quartz64-b-rk3566_defconfig)
+     - Pine64 SOQuartz on Blade (soquartz-blade-rk3566_defconfig)
      - Pine64 SOQuartz on Model A (soquartz-model-a-rk3566_defconfig)
 
 * rk3588
Signature · 1 line
2.41.0
#19 lore raw

Re: [PATCH 4/5] board: rockchip: Add Pine64 SOQuartz on Blade

Quoted 10 lines · Jonas Karlman

The Pine64 SOQuartz Blade board is a carrier board for the SOQuartz CM4-compatible compute module. It features PoE, an M.2 slot, an SD card slot, HDMI, USB, serial and ethernet.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe
- USB host

Quoted 6 lines

Device tree is imported from linux v6.4.

---

[...]

Boot log with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf:
DDR V1.17 992b933606 typ 23/04/25-10:10:19
ln
LP4/4x derate en, other dram:1x trefi
ddrconfig:0
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS=1 Die BW=16 Size=4096MB
tdqss: cs0 dqs0: -24ps, dqs1: -72ps, dqs2: -24ps, dqs3: -72ps,

change to: 324MHz
clk skew:0x61

change to: 528MHz
clk skew:0x58

change to: 780MHz
clk skew:0x58

change to: 1056MHz(final freq)
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:22%
dram drv:40,odt:80
vref_ca:00000071
clk skew:0x2c
cs 0:
the read training result:
DQS0:0x3a, DQS1:0x3c, DQS2:0x3b, DQS3:0x38,

min  : 0xa  0x9  0x5  0x1  0x3  0x4  0x9  0x7 , 0x6  0x2  0x2  0x2  0x8  0xe  0xe  0xb ,
       0x8  0x7  0x8  0x6  0x5  0x1  0x5  0x6 , 0x2  0x2  0x7  0x2  0x7  0x4  0x3  0x2 ,
mid  :0x28 0x27 0x23 0x1f 0x21 0x22 0x27 0x25 ,0x24 0x20 0x21 0x21 0x25 0x2c 0x2c 0x29 ,
      0x27 0x26 0x25 0x24 0x23 0x20 0x23 0x24 ,0x20 0x20 0x24 0x20 0x25 0x22 0x22 0x21 ,
max  :0x46 0x46 0x41 0x3d 0x40 0x40 0x45 0x44 ,0x43 0x3f 0x40 0x41 0x43 0x4b 0x4b 0x48 ,
      0x46 0x45 0x43 0x43 0x41 0x3f 0x42 0x42 ,0x3f 0x3e 0x42 0x3e 0x43 0x41 0x41 0x40 ,
range:0x3c 0x3d 0x3c 0x3c 0x3d 0x3c 0x3c 0x3d ,0x3d 0x3d 0x3e 0x3f 0x3b 0x3d 0x3d 0x3d ,
      0x3e 0x3e 0x3b 0x3d 0x3c 0x3e 0x3d 0x3c ,0x3d 0x3c 0x3b 0x3c 0x3c 0x3d 0x3e 0x3e ,
the write training result:
DQS0:0x29, DQS1:0x23, DQS2:0x29, DQS3:0x23,
min  :0x51 0x55 0x4e 0x4c 0x4d 0x4d 0x52 0x52 0x54 ,0x46 0x43 0x43 0x46 0x49 0x4e 0x4f 0x4e 0x49 ,
      0x4d 0x4d 0x4e 0x4d 0x4b 0x48 0x4c 0x4e 0x4d ,0x44 0x46 0x48 0x46 0x4a 0x47 0x46 0x47 0x48 ,
mid  :0x6e 0x71 0x6a 0x67 0x68 0x69 0x6e 0x6d 0x6f ,0x62 0x60 0x5f 0x62 0x65 0x6b 0x6b 0x6a 0x66 ,
      0x6a 0x6a 0x6a 0x69 0x67 0x65 0x68 0x69 0x69 ,0x60 0x61 0x65 0x62 0x66 0x64 0x62 0x63 0x64 ,
max  :0x8b 0x8d 0x86 0x83 0x84 0x85 0x8a 0x89 0x8b ,0x7f 0x7d 0x7b 0x7e 0x82 0x88 0x88 0x86 0x83 ,
      0x88 0x87 0x86 0x86 0x84 0x82 0x84 0x85 0x86 ,0x7d 0x7c 0x82 0x7e 0x83 0x82 0x7e 0x80 0x80 ,
range:0x3a 0x38 0x38 0x37 0x37 0x38 0x38 0x37 0x37 ,0x39 0x3a 0x38 0x38 0x39 0x3a 0x39 0x38 0x3a ,
      0x3b 0x3a 0x38 0x39 0x39 0x3a 0x38 0x37 0x39 ,0x39 0x36 0x3a 0x38 0x39 0x3b 0x38 0x39 0x38 ,
CA Training result:
cs:0 min  :0x3d 0x3d 0x35 0x36 0x38 0x31 0x39 ,0x3c 0x36 0x39 0x35 0x39 0x32 0x3b ,
cs:0 mid  :0x7b 0x7d 0x73 0x77 0x76 0x72 0x68 ,0x79 0x77 0x77 0x76 0x76 0x73 0x69 ,
cs:0 max  :0xba 0xbe 0xb1 0xb8 0xb4 0xb3 0x97 ,0xb7 0xb8 0xb5 0xb7 0xb4 0xb4 0x98 ,

cs:0 range:0x7d 0x81 0x7c 0x82 0x7c 0x82 0x5e ,0x7b 0x82 0x7c 0x82 0x7b 0x82 0x5d , out

U-Boot SPL 2023.07 (Jul 23 2023 - 13:08:34 +0000) rockchip_sdhci_probe clk set rate fail! Trying to boot from MMC2
## Checking hash(es) for config config-1 ... OK ## Checking hash(es) for Image atf-1 ... sha256+ OK ## Checking hash(es) for Image u-boot ... sha256+ OK ## Checking hash(es) for Image fdt-1 ... sha256+ OK ## Checking hash(es) for Image atf-2 ... sha256+ OK ## Checking hash(es) for Image atf-3 ... sha256+ OK ## Checking hash(es) for Image atf-4 ... sha256+ OK ## Checking hash(es) for Image atf-5 ... sha256+ OK ## Checking hash(es) for Image atf-6 ... sha256+ OK

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-607-gbf602aff1:cl
NOTICE:  BL31: Built : 10:16:03, Jun  5 2023
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    pmu v1 is valid 220114
INFO:    dfs DDR fsp_param[0].freq_mhz= 1056MHz
INFO:    dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO:    dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO:    dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0xa00000
INFO:    SPSR = 0x3c9

U-Boot 2023.07 (Jul 23 2023 - 13:08:34 +0000)

Model: PINE64 RK3566 SOQuartz on Blade carrier board
DRAM:  4 GiB (effective 3.7 GiB)
PMIC:  RK8090 (on=0x40, off=0x00)
Core:  312 devices, 27 uclasses, devicetree: separate
MMC:   rockchip_sdhci_probe clk set rate fail!
mmc@fe2b0000: 1, mmc@fe2c0000: 2, mmc@fe310000: 0
Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: PINE64 RK3566 SOQuartz on Blade carrier board
Net:   No ethernet found.

Hit any key to stop autoboot: 0
=>

Regards,
Jonas

Reviewed-by on v1 4/5
#20 lore raw

Re: [PATCH 4/5] board: rockchip: Add Pine64 SOQuartz on Blade

In reply to Jonas Karlman
Quoted 10 lines · Jonas Karlman

The Pine64 SOQuartz Blade board is a carrier board for the SOQuartz CM4-compatible compute module. It features PoE, an M.2 slot, an SD card slot, HDMI, USB, serial and ethernet.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe
- USB host

Quoted 5 lines

Device tree is imported from linux v6.4.

Thanks,
- Kever

Quoted 361 lines
---
  arch/arm/dts/Makefile                         |   1 +
  .../arm/dts/rk3566-soquartz-blade-u-boot.dtsi |   3 +
  arch/arm/dts/rk3566-soquartz-blade.dts        | 194 ++++++++++++++++++
  board/pine64/quartz64_rk3566/MAINTAINERS      |   3 +
  configs/soquartz-blade-rk3566_defconfig       |  90 ++++++++
  doc/board/rockchip/rockchip.rst               |   1 +
  6 files changed, 292 insertions(+)

create mode 100644 arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-soquartz-blade.dts create mode 100644 configs/soquartz-blade-rk3566_defconfig

arch/arm/dts/Makefile +1 -0
index aca2ec44a888..7a41675ef89d 100644
@@ -170,6 +170,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \
  	rk3566-quartz64-a.dtb \
  	rk3566-quartz64-b.dtb \
  	rk3566-radxa-cm3-io.dtb \
+	rk3566-soquartz-blade.dtb \
  	rk3566-soquartz-model-a.dtb \
  	rk3568-evb.dtb \
  	rk3568-odroid-m1.dtb \
arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi new file +3 -0
new file mode 100644
index 000000000000..0e662eafa4c7
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk3566-soquartz-u-boot.dtsi"
arch/arm/dts/rk3566-soquartz-blade.dts new file +194 -0
new file mode 100644
index 000000000000..4e49bebf548b
@@ -0,0 +1,194 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+
+#include "rk3566-soquartz.dtsi"
+
+/ {
+	model = "PINE64 RK3566 SOQuartz on Blade carrier board";
+	compatible = "pine64,soquartz-blade", "pine64,soquartz", "rockchip,rk3566";
+
+	/* labeled VCC3V0_SD in schematic to not conflict with PMIC regulator */
+	vcc3v0_sd: vcc3v0-sd-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v0_sd";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	/* labeled VCC_SSD in schematic */
+	vcc3v3_pcie_p: vcc3v3-pcie-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_pcie_p";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vbus>;
+	};
+
+	vcc5v_dcin: vcc5v-dcin-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+};
+
+&combphy2 {
+	phy-supply = <&vcc3v3_sys>;
+	status = "okay";
+};
+
+&gmac1 {
+	status = "okay";
+};
+
+/*
+ * i2c1 is exposed on CM1 / Module1A
+ * pin 80 - SCL0 - i2c1_scl_m0, pullup to vcc3v3_pmu
+ * pin 82 - SDA0 - i2c1_sda_m0, pullup to vcc3v3_pmu
+ */
+&i2c1 {
+	status = "okay";
+
+};
+
+/*
+ * i2c2 is exposed on CM1 / Module1A - to PI40
+ * pin 56 - GPIO3 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch
+ * pin 58 - GPIO2 - i2c2_sda_m1, pullup to vcc_3v3
+ */
+&i2c2 {
+	status = "disabled";
+};
+
+/*
+ * i2c3 is exposed on CM1 / Module1A - to PI40
+ * pin 35 - ID_SC(GPIO28) - i2c3_scl_m0, pullup to vcc_3v3
+ * pin 36 - ID_SD(GPIO27) - i2c3_sda_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+	status = "disabled";
+};
+
+/*
+ * i2c4 is exposed on CM2 / Module1B - to PI40
+ * pin 45 - GPIO24 - i2c4_scl_m1
+ * pin 47 - GPIO23 - i2c4_sda_m1
+ */
+&i2c4 {
+	status = "disabled";
+};
+
+/*
+ * i2s1_8ch is exposed on CM1 / Module1A - to PI40
+ * pin 24 - GPIO26 - i2s1_sdi1_m1
+ * pin 25 - GPIO21 - i2s1_sdo0_m1
+ * pin 26 - GPIO19 - i2s1_lrck_tx_m1
+ * pin 27 - GPIO20 - i2s1_sdi0_m1
+ * pin 29 - GPIO16 - i2s1_sdi3_m1
+ * pin 30 - GPIO6  - i2s1_sdi2_m1
+ * pin 40 - GPIO9  - i2s1_sdo1_m1, shared with spi3
+ * pin 41 - GPIO25 - i2s1_sdo2_m1
+ * pin 49 - GPIO18 - i2s1_sclk_tx_m1
+ * pin 50 - GPIO17 - i2s1_mclk_m1
+ * pin 56 - GPIO3  - i2s1_sdo3_m1, shared with i2c2
+ */
+&i2s1_8ch {
+	status = "disabled";
+};
+
+&led_diy {
+	color = <LED_COLOR_ID_RED>;
+	function = LED_FUNCTION_DISK_ACTIVITY;
+	linux,default-trigger = "disk-activity";
+	status = "okay";
+};
+
+&led_work {
+	color = <LED_COLOR_ID_GREEN>;
+	function = LED_FUNCTION_STATUS;
+	linux,default-trigger = "heartbeat";
+	status = "okay";
+};
+
+&pcie2x1 {
+	vpcie3v3-supply = <&vcc3v3_pcie_p>;
+	status = "okay";
+};
+
+&rgmii_phy1 {
+	status = "okay";
+};
+
+/*
+ * saradc is exposed on CM1 / Module1A - to J2
+ * pin 94 - AIN1 - saradc_vin3
+ * pin 96 - AIN0 - saradc_vin2
+ */
+&saradc {
+	status = "disabled";
+};
+
+&sdmmc0 {
+	vmmc-supply = <&vcc3v0_sd>;
+	status = "okay";
+};
+
+/*
+ * spi3 is exposed on CM1 / Module1A - to PI40
+ * pin 37 - GPIO7  - spi3_cs1_m0
+ * pin 38 - GPIO11 - spi3_clk_m0
+ * pin 39 - GPIO8  - spi3_cs0_m0
+ * pin 40 - GPIO9  - spi3_miso_m0, shared with i2s1_8ch
+ * pin 44 - GPIO10 - spi3_mosi_m0
+ */
+&spi3 {
+	status = "disabled";
+};
+
+/*
+ * uart2 is exposed on CM1 / Module1A - to PI40
+ * pin 51 - GPIO15 - uart2_rx_m0
+ * pin 55 - GPIO14 - uart2_tx_m0
+ */
+&uart2 {
+	status = "okay";
+};
+
+/*
+ * uart7 is exposed on CM1 / Module1A - to PI40
+ * pin 46 - GPIO22 - uart7_tx_m2
+ * pin 47 - GPIO23 - uart7_rx_m2
+ */
+&uart7 {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vbus>;
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	status = "okay";
+};
+
+&vbus {
+	vin-supply = <&vcc5v_dcin>;
+};
board/pine64/quartz64_rk3566/MAINTAINERS +3 -0
index 748ff5033d93..603d2ee9d5e9 100644
@@ -6,6 +6,7 @@ F:	board/pine64/quartz64_rk3566/
  F:	include/configs/quartz64_rk3566.h
  F:	configs/quartz64-a-rk3566_defconfig
  F:	configs/quartz64-b-rk3566_defconfig
+F:	configs/soquartz-blade-rk3566_defconfig
  F:	configs/soquartz-model-a-rk3566_defconfig
  F:	arch/arm/dts/rk3566-quartz64-a.dts
  F:	arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
@@ -13,5 +14,7 @@ F:	arch/arm/dts/rk3566-quartz64-b.dts
  F:	arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi
  F:	arch/arm/dts/rk3566-soquartz.dtsi
  F:	arch/arm/dts/rk3566-soquartz-u-boot.dtsi
+F:	arch/arm/dts/rk3566-soquartz-blade.dts
+F:	arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi
  F:	arch/arm/dts/rk3566-soquartz-model-a.dts
  F:	arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
configs/soquartz-blade-rk3566_defconfig new file +90 -0
new file mode 100644
index 000000000000..181c284e73e9
@@ -0,0 +1,90 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TEXT_BASE=0x00a00000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
+CONFIG_DEFAULT_DEVICE_TREE="rk3566-soquartz-blade"
+CONFIG_ROCKCHIP_RK3568=y
+CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_TARGET_QUARTZ64_RK3566=y
+CONFIG_SPL_STACK=0x400000
+CONFIG_DEBUG_UART_BASE=0xFE660000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SYS_LOAD_ADDR=0xc00800
+CONFIG_PCI=y
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_FIT_SIGNATURE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-soquartz-blade.dtb"
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_MAX_SIZE=0x40000
+CONFIG_SPL_PAD_TO=0x7f8000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x4000000
+CONFIG_SPL_BSS_MAX_SIZE=0x4000
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_ATF=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIVE=y
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_SYSCON=y
+CONFIG_SCSI_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_SPL_CLK=y
+CONFIG_GPIO_HOG=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
+CONFIG_SUPPORT_EMMC_RPMB=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_ROCKCHIP=y
+CONFIG_NVME_PCI=y
+CONFIG_PCIE_DW_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_SPL_RAM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_BAUDRATE=1500000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_ERRNO_STR=y
doc/board/rockchip/rockchip.rst +1 -0
index a17bcb2afc1a..254a68b43eaf 100644
@@ -98,6 +98,7 @@ List of mainline supported Rockchip boards:
       - Hardkernel ODROID-M1 (odroid-m1-rk3568)
       - Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig)
       - Pine64 Quartz64-B Board (quartz64-b-rk3566_defconfig)
+     - Pine64 SOQuartz on Blade (soquartz-blade-rk3566_defconfig)
       - Pine64 SOQuartz on Model A (soquartz-model-a-rk3566_defconfig)
 
  * rk3588
#21 lore raw

PATCH 5/5 board: rockchip: Add Pine64 SOQuartz on CM4-IO

In reply to Jonas Karlman

The Pine64 SOQuartz compute module is mostly pin-compatible with the RPi CM4 form factor. Therefore, it can slot into the official Raspberry Pi CM4 IO carrier board. Add this configuration to U-Boot.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- USB host

Device tree is imported from linux v6.4.

---
 arch/arm/dts/Makefile                        |   1 +
 arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi |   3 +
 arch/arm/dts/rk3566-soquartz-cm4.dts         | 192 +++++++++++++++++++
 board/pine64/quartz64_rk3566/MAINTAINERS     |   3 +
 configs/soquartz-cm4-rk3566_defconfig        |  90 +++++++++
 doc/board/rockchip/rockchip.rst              |   1 +
 6 files changed, 290 insertions(+)
 create mode 100644 arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi
 create mode 100644 arch/arm/dts/rk3566-soquartz-cm4.dts
 create mode 100644 configs/soquartz-cm4-rk3566_defconfig
arch/arm/dts/Makefile +1 -0
index 7a41675ef89d..dabbf116914c 100644
@@ -171,6 +171,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \
 	rk3566-quartz64-b.dtb \
 	rk3566-radxa-cm3-io.dtb \
 	rk3566-soquartz-blade.dtb \
+	rk3566-soquartz-cm4.dtb \
 	rk3566-soquartz-model-a.dtb \
 	rk3568-evb.dtb \
 	rk3568-odroid-m1.dtb \
arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi new file +3 -0
new file mode 100644
index 000000000000..0e662eafa4c7
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk3566-soquartz-u-boot.dtsi"
arch/arm/dts/rk3566-soquartz-cm4.dts new file +192 -0

192 lines not on this page · raw message

board/pine64/quartz64_rk3566/MAINTAINERS +3 -0
index 603d2ee9d5e9..6b75b35a1243 100644
@@ -7,6 +7,7 @@ F:	include/configs/quartz64_rk3566.h
 F:	configs/quartz64-a-rk3566_defconfig
 F:	configs/quartz64-b-rk3566_defconfig
 F:	configs/soquartz-blade-rk3566_defconfig
+F:	configs/soquartz-cm4-rk3566_defconfig
 F:	configs/soquartz-model-a-rk3566_defconfig
 F:	arch/arm/dts/rk3566-quartz64-a.dts
 F:	arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
@@ -16,5 +17,7 @@ F:	arch/arm/dts/rk3566-soquartz.dtsi
 F:	arch/arm/dts/rk3566-soquartz-u-boot.dtsi
 F:	arch/arm/dts/rk3566-soquartz-blade.dts
 F:	arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi
+F:	arch/arm/dts/rk3566-soquartz-cm4.dts
+F:	arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi
 F:	arch/arm/dts/rk3566-soquartz-model-a.dts
 F:	arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
configs/soquartz-cm4-rk3566_defconfig new file +90 -0

90 lines not on this page · raw message

doc/board/rockchip/rockchip.rst +1 -0
index 254a68b43eaf..3cd5de55120b 100644
@@ -99,6 +99,7 @@ List of mainline supported Rockchip boards:
      - Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig)
      - Pine64 Quartz64-B Board (quartz64-b-rk3566_defconfig)
      - Pine64 SOQuartz on Blade (soquartz-blade-rk3566_defconfig)
+     - Pine64 SOQuartz on CM4-IO (soquartz-cm4-rk3566_defconfig)
      - Pine64 SOQuartz on Model A (soquartz-model-a-rk3566_defconfig)
 
 * rk3588
Signature · 1 line
2.41.0
#22 lore raw

Re: [PATCH 5/5] board: rockchip: Add Pine64 SOQuartz on CM4-IO

Quoted 9 lines · Jonas Karlman

The Pine64 SOQuartz compute module is mostly pin-compatible with the RPi CM4 form factor. Therefore, it can slot into the official Raspberry Pi CM4 IO carrier board. Add this configuration to U-Boot.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- USB host

Quoted 6 lines

Device tree is imported from linux v6.4.

---

[...]

Boot log with ROCKCHIP_TPL=rk3566_ddr_1056MHz_v1.17.bin and BL31=rk3568_bl31_v1.43.elf:

DDR V1.17 992b933606 typ 23/04/25-10:10:19
ln
LP4/4x derate en, other dram:1x trefi
ddrconfig:0
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS=1 Die BW=16 Size=4096MB
tdqss: cs0 dqs0: -24ps, dqs1: -72ps, dqs2: -24ps, dqs3: -72ps,

change to: 324MHz
clk skew:0x61

change to: 528MHz
clk skew:0x58

change to: 780MHz
clk skew:0x58

change to: 1056MHz(final freq)
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:22%
dram drv:40,odt:80
vref_ca:00000071
clk skew:0x2c
cs 0:
the read training result:
DQS0:0x3a, DQS1:0x3c, DQS2:0x3b, DQS3:0x37,

min  : 0xa  0x9  0x5  0x1  0x4  0x4  0x9  0x7 , 0x6  0x2  0x2  0x1  0x8  0xe  0xe  0xb ,
       0x8  0x6  0x8  0x6  0x5  0x2  0x5  0x6 , 0x1  0x1  0x6  0x1  0x6  0x3  0x3  0x2 ,
mid  :0x28 0x28 0x23 0x1f 0x22 0x22 0x27 0x25 ,0x24 0x20 0x21 0x21 0x25 0x2c 0x2d 0x29 ,
      0x27 0x25 0x25 0x24 0x23 0x20 0x23 0x24 ,0x20 0x1f 0x24 0x1f 0x24 0x22 0x21 0x20 ,
max  :0x46 0x47 0x41 0x3d 0x40 0x40 0x45 0x44 ,0x43 0x3f 0x40 0x41 0x43 0x4b 0x4c 0x48 ,
      0x46 0x45 0x43 0x43 0x41 0x3f 0x42 0x42 ,0x3f 0x3d 0x42 0x3d 0x42 0x41 0x40 0x3e ,
range:0x3c 0x3e 0x3c 0x3c 0x3c 0x3c 0x3c 0x3d ,0x3d 0x3d 0x3e 0x40 0x3b 0x3d 0x3e 0x3d ,
      0x3e 0x3f 0x3b 0x3d 0x3c 0x3d 0x3d 0x3c ,0x3e 0x3c 0x3c 0x3c 0x3c 0x3e 0x3d 0x3c ,
the write training result:
DQS0:0x29, DQS1:0x23, DQS2:0x29, DQS3:0x23,
min  :0x51 0x55 0x4e 0x4b 0x4d 0x4d 0x52 0x53 0x55 ,0x46 0x43 0x43 0x46 0x49 0x4e 0x4f 0x4e 0x49 ,
      0x4d 0x4d 0x4e 0x4d 0x4b 0x48 0x4c 0x4e 0x4d ,0x44 0x46 0x48 0x46 0x4a 0x47 0x46 0x47 0x49 ,
mid  :0x6e 0x71 0x6a 0x67 0x69 0x69 0x6e 0x6e 0x70 ,0x62 0x60 0x5f 0x62 0x65 0x6b 0x6b 0x6a 0x66 ,
      0x6a 0x6a 0x6a 0x69 0x67 0x65 0x68 0x69 0x69 ,0x60 0x61 0x65 0x62 0x66 0x64 0x62 0x63 0x65 ,
max  :0x8b 0x8d 0x86 0x83 0x85 0x85 0x8a 0x89 0x8b ,0x7f 0x7d 0x7b 0x7e 0x82 0x88 0x88 0x86 0x83 ,
      0x88 0x87 0x86 0x86 0x84 0x82 0x84 0x85 0x86 ,0x7c 0x7c 0x83 0x7e 0x83 0x81 0x7e 0x80 0x81 ,
range:0x3a 0x38 0x38 0x38 0x38 0x38 0x38 0x36 0x36 ,0x39 0x3a 0x38 0x38 0x39 0x3a 0x39 0x38 0x3a ,
      0x3b 0x3a 0x38 0x39 0x39 0x3a 0x38 0x37 0x39 ,0x38 0x36 0x3b 0x38 0x39 0x3a 0x38 0x39 0x38 ,
CA Training result:
cs:0 min  :0x3c 0x3c 0x35 0x36 0x37 0x30 0x39 ,0x3b 0x36 0x39 0x36 0x38 0x33 0x3b ,
cs:0 mid  :0x7a 0x7c 0x73 0x77 0x75 0x71 0x68 ,0x79 0x77 0x77 0x76 0x75 0x73 0x69 ,
cs:0 max  :0xb9 0xbd 0xb1 0xb8 0xb4 0xb3 0x97 ,0xb7 0xb8 0xb5 0xb7 0xb3 0xb4 0x98 ,

cs:0 range:0x7d 0x81 0x7c 0x82 0x7d 0x83 0x5e ,0x7c 0x82 0x7c 0x81 0x7b 0x81 0x5d , out

U-Boot SPL 2023.07 (Jul 23 2023 - 13:39:45 +0000) rockchip_sdhci_probe clk set rate fail! Trying to boot from MMC2
## Checking hash(es) for config config-1 ... OK ## Checking hash(es) for Image atf-1 ... sha256+ OK ## Checking hash(es) for Image u-boot ... sha256+ OK ## Checking hash(es) for Image fdt-1 ... sha256+ OK ## Checking hash(es) for Image atf-2 ... sha256+ OK ## Checking hash(es) for Image atf-3 ... sha256+ OK ## Checking hash(es) for Image atf-4 ... sha256+ OK ## Checking hash(es) for Image atf-5 ... sha256+ OK ## Checking hash(es) for Image atf-6 ... sha256+ OK

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-607-gbf602aff1:cl
NOTICE:  BL31: Built : 10:16:03, Jun  5 2023
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    pmu v1 is valid 220114
INFO:    dfs DDR fsp_param[0].freq_mhz= 1056MHz
INFO:    dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO:    dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO:    dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0xa00000
INFO:    SPSR = 0x3c9

U-Boot 2023.07 (Jul 23 2023 - 13:39:45 +0000)

Model: Pine64 RK3566 SoQuartz with CM4-IO Carrier Board
DRAM:  4 GiB (effective 3.7 GiB)
PMIC:  RK8090 (on=0x40, off=0x00)
Core:  312 devices, 27 uclasses, devicetree: separate
MMC:   rockchip_sdhci_probe clk set rate fail!
mmc@fe2b0000: 1, mmc@fe2c0000: 2, mmc@fe310000: 0
Loading Environment from nowhere... OK
In:    serial@fe660000
Out:   serial@fe660000
Err:   serial@fe660000
Model: Pine64 RK3566 SoQuartz with CM4-IO Carrier Board
Net:   No ethernet found.

Hit any key to stop autoboot: 0
=>

Regards,
Jonas

Reviewed-by on v1 5/5
#23 lore raw

Re: [PATCH 5/5] board: rockchip: Add Pine64 SOQuartz on CM4-IO

In reply to Jonas Karlman
Quoted 9 lines · Jonas Karlman

The Pine64 SOQuartz compute module is mostly pin-compatible with the RPi CM4 form factor. Therefore, it can slot into the official Raspberry Pi CM4 IO carrier board. Add this configuration to U-Boot.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- USB host

Quoted 5 lines

Device tree is imported from linux v6.4.

Thanks,
- Kever

Quoted 359 lines
---
  arch/arm/dts/Makefile                        |   1 +
  arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi |   3 +
  arch/arm/dts/rk3566-soquartz-cm4.dts         | 192 +++++++++++++++++++
  board/pine64/quartz64_rk3566/MAINTAINERS     |   3 +
  configs/soquartz-cm4-rk3566_defconfig        |  90 +++++++++
  doc/board/rockchip/rockchip.rst              |   1 +
  6 files changed, 290 insertions(+)

create mode 100644 arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-soquartz-cm4.dts create mode 100644 configs/soquartz-cm4-rk3566_defconfig

arch/arm/dts/Makefile +1 -0
index 7a41675ef89d..dabbf116914c 100644
@@ -171,6 +171,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \
  	rk3566-quartz64-b.dtb \
  	rk3566-radxa-cm3-io.dtb \
  	rk3566-soquartz-blade.dtb \
+	rk3566-soquartz-cm4.dtb \
  	rk3566-soquartz-model-a.dtb \
  	rk3568-evb.dtb \
  	rk3568-odroid-m1.dtb \
arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi new file +3 -0
new file mode 100644
index 000000000000..0e662eafa4c7
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk3566-soquartz-u-boot.dtsi"
arch/arm/dts/rk3566-soquartz-cm4.dts new file +192 -0
new file mode 100644
index 000000000000..cddf6cd2fecb
@@ -0,0 +1,192 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-soquartz.dtsi"
+
+/ {
+	model = "Pine64 RK3566 SoQuartz with CM4-IO Carrier Board";
+	compatible = "pine64,soquartz-cm4io", "pine64,soquartz", "rockchip,rk3566";
+
+	/* labeled +12v in schematic */
+	vcc12v_dcin: vcc12v-dcin-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	/* labeled +5v in schematic */
+	vcc_5v: vcc-5v-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_5v";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc_sd_pwr: vcc-sd-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sd_pwr";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+};
+
+/* phy for pcie */
+&combphy2 {
+	phy-supply = <&vcc3v3_sys>;
+	status = "okay";
+};
+
+&gmac1 {
+	status = "okay";
+};
+
+/*
+ * i2c1 is exposed on CM1 / Module1A
+ * pin 80 - SCL0 - i2c1_scl_m0, pullup to vcc3v3_pmu
+ * pin 82 - SDA0 - i2c1_sda_m0, pullup to vcc3v3_pmu
+ */
+&i2c1 {
+	status = "okay";
+
+	/*
+	 * the rtc interrupt is tied to PMIC_PWRON,
+	 * it will force reset the board if triggered.
+	 */
+	pcf85063: rtc@51 {
+		compatible = "nxp,pcf85063";
+		reg = <0x51>;
+	};
+};
+
+/*
+ * i2c2 is exposed on CM1 / Module1A - to PI40
+ * pin 56 - GPIO3 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch
+ * pin 58 - GPIO2 - i2c2_sda_m1, pullup to vcc_3v3
+ */
+&i2c2 {
+	status = "disabled";
+};
+
+/*
+ * i2c3 is exposed on CM1 / Module1A - to PI40
+ * pin 35 - ID_SC(GPIO28) - i2c3_scl_m0, pullup to vcc_3v3
+ * pin 36 - ID_SD(GPIO27) - i2c3_sda_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+	status = "disabled";
+};
+
+/*
+ * i2c4 is exposed on CM2 / Module1B - to PI40
+ * pin 45 - GPIO24 - i2c4_scl_m1
+ * pin 47 - GPIO23 - i2c4_sda_m1
+ */
+&i2c4 {
+	status = "disabled";
+};
+
+/*
+ * i2s1_8ch is exposed on CM1 / Module1A - to PI40
+ * pin 24 - GPIO26 - i2s1_sdi1_m1
+ * pin 25 - GPIO21 - i2s1_sdo0_m1
+ * pin 26 - GPIO19 - i2s1_lrck_tx_m1
+ * pin 27 - GPIO20 - i2s1_sdi0_m1
+ * pin 29 - GPIO16 - i2s1_sdi3_m1
+ * pin 30 - GPIO6  - i2s1_sdi2_m1
+ * pin 40 - GPIO9  - i2s1_sdo1_m1, shared with spi3
+ * pin 41 - GPIO25 - i2s1_sdo2_m1
+ * pin 49 - GPIO18 - i2s1_sclk_tx_m1
+ * pin 50 - GPIO17 - i2s1_mclk_m1
+ * pin 56 - GPIO3  - i2s1_sdo3_m1, shared with i2c2
+ */
+&i2s1_8ch {
+	status = "disabled";
+};
+
+&led_diy {
+	status = "okay";
+};
+
+&led_work {
+	status = "okay";
+};
+
+&pcie2x1 {
+	vpcie3v3-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&rgmii_phy1 {
+	status = "okay";
+};
+
+/*
+ * saradc is exposed on CM1 / Module1A - to J2
+ * pin 94 - AIN1 - saradc_vin3
+ * pin 96 - AIN0 - saradc_vin2
+ */
+&saradc {
+	status = "disabled";
+};
+
+&sdmmc0 {
+	vmmc-supply = <&vcc_sd_pwr>;
+	status = "okay";
+};
+
+/*
+ *  spi3 is exposed on CM1 / Module1A - to PI40
+ * pin 37 - GPIO7  - spi3_cs1_m0
+ * pin 38 - GPIO11 - spi3_clk_m0
+ * pin 39 - GPIO8  - spi3_cs0_m0
+ * pin 40 - GPIO9  - spi3_miso_m0, shared with i2s1_8ch
+ * pin 44 - GPIO10 - spi3_mosi_m0
+ */
+&spi3 {
+	status = "disabled";
+};
+
+/*
+ * uart2 is exposed on CM1 / Module1A - to PI40
+ * pin 51 - GPIO15 - uart2_rx_m0
+ * pin 55 - GPIO14 - uart2_tx_m0
+ */
+&uart2 {
+	status = "okay";
+};
+
+/*
+ * uart7 is exposed on CM1 / Module1A - to PI40
+ * pin 46 - GPIO22 - uart7_tx_m2
+ * pin 47 - GPIO23 - uart7_rx_m2
+ */
+&uart7 {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc_5v>;
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	status = "okay";
+};
+
+&vbus {
+	vin-supply = <&vcc_5v>;
+};
board/pine64/quartz64_rk3566/MAINTAINERS +3 -0
index 603d2ee9d5e9..6b75b35a1243 100644
@@ -7,6 +7,7 @@ F:	include/configs/quartz64_rk3566.h
  F:	configs/quartz64-a-rk3566_defconfig
  F:	configs/quartz64-b-rk3566_defconfig
  F:	configs/soquartz-blade-rk3566_defconfig
+F:	configs/soquartz-cm4-rk3566_defconfig
  F:	configs/soquartz-model-a-rk3566_defconfig
  F:	arch/arm/dts/rk3566-quartz64-a.dts
  F:	arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
@@ -16,5 +17,7 @@ F:	arch/arm/dts/rk3566-soquartz.dtsi
  F:	arch/arm/dts/rk3566-soquartz-u-boot.dtsi
  F:	arch/arm/dts/rk3566-soquartz-blade.dts
  F:	arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi
+F:	arch/arm/dts/rk3566-soquartz-cm4.dts
+F:	arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi
  F:	arch/arm/dts/rk3566-soquartz-model-a.dts
  F:	arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
configs/soquartz-cm4-rk3566_defconfig new file +90 -0
new file mode 100644
index 000000000000..7e290351477e
@@ -0,0 +1,90 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TEXT_BASE=0x00a00000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
+CONFIG_DEFAULT_DEVICE_TREE="rk3566-soquartz-cm4"
+CONFIG_ROCKCHIP_RK3568=y
+CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_TARGET_QUARTZ64_RK3566=y
+CONFIG_SPL_STACK=0x400000
+CONFIG_DEBUG_UART_BASE=0xFE660000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SYS_LOAD_ADDR=0xc00800
+CONFIG_PCI=y
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_FIT_SIGNATURE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-soquartz-cm4.dtb"
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_MAX_SIZE=0x40000
+CONFIG_SPL_PAD_TO=0x7f8000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x4000000
+CONFIG_SPL_BSS_MAX_SIZE=0x4000
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_ATF=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIVE=y
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_SYSCON=y
+CONFIG_SCSI_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_SPL_CLK=y
+CONFIG_GPIO_HOG=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
+CONFIG_SUPPORT_EMMC_RPMB=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_ROCKCHIP=y
+CONFIG_NVME_PCI=y
+CONFIG_PCIE_DW_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_SPL_RAM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_BAUDRATE=1500000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_ERRNO_STR=y
doc/board/rockchip/rockchip.rst +1 -0
index 254a68b43eaf..3cd5de55120b 100644
@@ -99,6 +99,7 @@ List of mainline supported Rockchip boards:
       - Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig)
       - Pine64 Quartz64-B Board (quartz64-b-rk3566_defconfig)
       - Pine64 SOQuartz on Blade (soquartz-blade-rk3566_defconfig)
+     - Pine64 SOQuartz on CM4-IO (soquartz-cm4-rk3566_defconfig)
       - Pine64 SOQuartz on Model A (soquartz-model-a-rk3566_defconfig)
 
  * rk3588
#24 lore raw
In reply to Jonas Karlman
Quoted 9 lines · Jonas Karlman

This series was created in collaboration with Nicolas Frattaroli and add support for Pine64 Quartz64 and SOQuartz boards with a RK3566 SoC.

- Pine64 Quartz64-A Board
- Pine64 Quartz64-B Board
- Pine64 SOQuartz on Model A
- Pine64 SOQuartz on Blade
- Pine64 SOQuartz on CM4-IO

Quoted 5 lines

Device trees have been imported from linux v6.4.

This series have loose dependencies on the following series:
- rockchip: Fix PCIe and NVMe support on RK3568 [1]
- rockchip: rk3568: Use dwc3-generic driver [2]

This patch is still waiting for review, and this patchset may need to update once it get merged.

Thanks,
- Kever

Quoted 71 lines

- rockchip: rk3568: Fix alloc space exhausted in SPL [3]
- rockchip: rk3568: Device Tree updates [4]
- rockchip: rk35xx: Fix SPI Flash alias [5]
- board: rockchip: Add Hardkernel ODROID-M1 [6]

A copy of this series with above dependencies can be found at [7].

[1] https://patchwork.ozlabs.org/project/uboot/list/?series=365195
[2] https://patchwork.ozlabs.org/project/uboot/list/?series=364127
[3] https://patchwork.ozlabs.org/project/uboot/list/?series=361999
[4] https://patchwork.ozlabs.org/project/uboot/list/?series=362030
[5] https://patchwork.ozlabs.org/project/uboot/list/?series=363527
[6] https://patchwork.ozlabs.org/project/uboot/list/?series=365198
[7] https://github.com/Kwiboo/u-boot-rockchip/commits/rk3568-quartz64-v1

Jonas Karlman (5):
board: rockchip: Add Pine64 Quartz64-A Board
board: rockchip: Add Pine64 Quartz64-B Board
board: rockchip: Add Pine64 SOQuartz on Model A
board: rockchip: Add Pine64 SOQuartz on Blade
board: rockchip: Add Pine64 SOQuartz on CM4-IO

  arch/arm/dts/Makefile                         |   5 +
  arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi    |  55 ++
  arch/arm/dts/rk3566-quartz64-a.dts            | 839 ++++++++++++++++++
  arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi    |  47 +
  arch/arm/dts/rk3566-quartz64-b.dts            | 739 +++++++++++++++
  .../arm/dts/rk3566-soquartz-blade-u-boot.dtsi |   3 +
  arch/arm/dts/rk3566-soquartz-blade.dts        | 194 ++++
  arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi  |   3 +
  arch/arm/dts/rk3566-soquartz-cm4.dts          | 192 ++++
  .../dts/rk3566-soquartz-model-a-u-boot.dtsi   |   3 +
  arch/arm/dts/rk3566-soquartz-model-a.dts      | 232 +++++
  arch/arm/dts/rk3566-soquartz-u-boot.dtsi      |  30 +
  arch/arm/dts/rk3566-soquartz.dtsi             | 688 ++++++++++++++
  arch/arm/mach-rockchip/rk3568/Kconfig         |   6 +
  board/pine64/quartz64_rk3566/Kconfig          |  15 +
  board/pine64/quartz64_rk3566/MAINTAINERS      |  23 +
  board/pine64/quartz64_rk3566/Makefile         |   3 +
  .../pine64/quartz64_rk3566/quartz64-rk3566.c  |   1 +
  configs/quartz64-a-rk3566_defconfig           | 110 +++
  configs/quartz64-b-rk3566_defconfig           | 106 +++
  configs/soquartz-blade-rk3566_defconfig       |  90 ++
  configs/soquartz-cm4-rk3566_defconfig         |  90 ++
  configs/soquartz-model-a-rk3566_defconfig     |  90 ++
  doc/board/rockchip/rockchip.rst               |   5 +
  include/configs/quartz64_rk3566.h             |  10 +
  25 files changed, 3579 insertions(+)

create mode 100644 arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-quartz64-a.dts create mode 100644 arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-quartz64-b.dts create mode 100644 arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-soquartz-blade.dts create mode 100644 arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-soquartz-cm4.dts create mode 100644 arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-soquartz-model-a.dts create mode 100644 arch/arm/dts/rk3566-soquartz-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-soquartz.dtsi create mode 100644 board/pine64/quartz64_rk3566/Kconfig create mode 100644 board/pine64/quartz64_rk3566/MAINTAINERS create mode 100644 board/pine64/quartz64_rk3566/Makefile create mode 100644 board/pine64/quartz64_rk3566/quartz64-rk3566.c create mode 100644 configs/quartz64-a-rk3566_defconfig create mode 100644 configs/quartz64-b-rk3566_defconfig create mode 100644 configs/soquartz-blade-rk3566_defconfig create mode 100644 configs/soquartz-cm4-rk3566_defconfig create mode 100644 configs/soquartz-model-a-rk3566_defconfig create mode 100644 include/configs/quartz64_rk3566.h

#25 lore raw
Quoted 11 lines · Kever Yang
Quoted 9 lines · Jonas Karlman

This series was created in collaboration with Nicolas Frattaroli and add support for Pine64 Quartz64 and SOQuartz boards with a RK3566 SoC.

- Pine64 Quartz64-A Board
- Pine64 Quartz64-B Board
- Pine64 SOQuartz on Model A
- Pine64 SOQuartz on Blade
- Pine64 SOQuartz on CM4-IO

Quoted 8 lines
Quoted 5 lines

Device trees have been imported from linux v6.4.

This series have loose dependencies on the following series:
- rockchip: Fix PCIe and NVMe support on RK3568 [1]
- rockchip: rk3568: Use dwc3-generic driver [2]

This patch is still waiting for review, and this patchset may need to update once it get merged.

Thanks, I have re-sent the following series that I hope should help you with applying.
- "rockchip: rk3568: Device Tree updates" v2
- "rockchip: rk35xx: Fix SPI Flash alias" v2
- "rockchip: rk3568: Use dwc3-generic driver" v4

There may only be a runtime depend on the patch "usb: dwc3-generic:
Relax unsupported dr_mode check" of the "rockchip: rk3568: Use dwc3-generic driver" series. Or it may not be since we define dr_mode = "host" on some of these boards. Our runtime testing has however been done with all the mentioned series applied.

Will re-send this series if needed :-)

Regards,
Jonas

Quoted 74 lines

Thanks,
- Kever

Quoted 71 lines

- rockchip: rk3568: Fix alloc space exhausted in SPL [3]
- rockchip: rk3568: Device Tree updates [4]
- rockchip: rk35xx: Fix SPI Flash alias [5]
- board: rockchip: Add Hardkernel ODROID-M1 [6]

A copy of this series with above dependencies can be found at [7].

[1] https://patchwork.ozlabs.org/project/uboot/list/?series=365195
[2] https://patchwork.ozlabs.org/project/uboot/list/?series=364127
[3] https://patchwork.ozlabs.org/project/uboot/list/?series=361999
[4] https://patchwork.ozlabs.org/project/uboot/list/?series=362030
[5] https://patchwork.ozlabs.org/project/uboot/list/?series=363527
[6] https://patchwork.ozlabs.org/project/uboot/list/?series=365198
[7] https://github.com/Kwiboo/u-boot-rockchip/commits/rk3568-quartz64-v1

Jonas Karlman (5):
board: rockchip: Add Pine64 Quartz64-A Board
board: rockchip: Add Pine64 Quartz64-B Board
board: rockchip: Add Pine64 SOQuartz on Model A
board: rockchip: Add Pine64 SOQuartz on Blade
board: rockchip: Add Pine64 SOQuartz on CM4-IO

  arch/arm/dts/Makefile                         |   5 +
  arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi    |  55 ++
  arch/arm/dts/rk3566-quartz64-a.dts            | 839 ++++++++++++++++++
  arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi    |  47 +
  arch/arm/dts/rk3566-quartz64-b.dts            | 739 +++++++++++++++
  .../arm/dts/rk3566-soquartz-blade-u-boot.dtsi |   3 +
  arch/arm/dts/rk3566-soquartz-blade.dts        | 194 ++++
  arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi  |   3 +
  arch/arm/dts/rk3566-soquartz-cm4.dts          | 192 ++++
  .../dts/rk3566-soquartz-model-a-u-boot.dtsi   |   3 +
  arch/arm/dts/rk3566-soquartz-model-a.dts      | 232 +++++
  arch/arm/dts/rk3566-soquartz-u-boot.dtsi      |  30 +
  arch/arm/dts/rk3566-soquartz.dtsi             | 688 ++++++++++++++
  arch/arm/mach-rockchip/rk3568/Kconfig         |   6 +
  board/pine64/quartz64_rk3566/Kconfig          |  15 +
  board/pine64/quartz64_rk3566/MAINTAINERS      |  23 +
  board/pine64/quartz64_rk3566/Makefile         |   3 +
  .../pine64/quartz64_rk3566/quartz64-rk3566.c  |   1 +
  configs/quartz64-a-rk3566_defconfig           | 110 +++
  configs/quartz64-b-rk3566_defconfig           | 106 +++
  configs/soquartz-blade-rk3566_defconfig       |  90 ++
  configs/soquartz-cm4-rk3566_defconfig         |  90 ++
  configs/soquartz-model-a-rk3566_defconfig     |  90 ++
  doc/board/rockchip/rockchip.rst               |   5 +
  include/configs/quartz64_rk3566.h             |  10 +
  25 files changed, 3579 insertions(+)

create mode 100644 arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-quartz64-a.dts create mode 100644 arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-quartz64-b.dts create mode 100644 arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-soquartz-blade.dts create mode 100644 arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-soquartz-cm4.dts create mode 100644 arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-soquartz-model-a.dts create mode 100644 arch/arm/dts/rk3566-soquartz-u-boot.dtsi create mode 100644 arch/arm/dts/rk3566-soquartz.dtsi create mode 100644 board/pine64/quartz64_rk3566/Kconfig create mode 100644 board/pine64/quartz64_rk3566/MAINTAINERS create mode 100644 board/pine64/quartz64_rk3566/Makefile create mode 100644 board/pine64/quartz64_rk3566/quartz64-rk3566.c create mode 100644 configs/quartz64-a-rk3566_defconfig create mode 100644 configs/quartz64-b-rk3566_defconfig create mode 100644 configs/soquartz-blade-rk3566_defconfig create mode 100644 configs/soquartz-cm4-rk3566_defconfig create mode 100644 configs/soquartz-model-a-rk3566_defconfig create mode 100644 include/configs/quartz64_rk3566.h