Skip to contentSkip to conversation

Meson8b support for the meson_saradc driver

PATCH New Martin Blumenstingl 4 participants 8 messages Mar 25, 2017 – Mar 30, 2017

Subsystems (3)
lore
Share & tools
lore

Martin Blumenstingl

author reviewer
#0 lore raw

cover Meson8b support for the meson_saradc driver

The SAR ADC register layout seems to be mostly the same on older SoCs. Thus basically all functionality is already supported by the existing driver.

There are two small differences though:
- the adc_clk and adc_div clock are not provided by the clock-controller on Meson8b. instead the SAR ADC provides an internal "adc_clk" (this behavior is already supported by the driver and requires no changes)
- the newer SoCs are using some register bits only the kernel or the BL30 (bootloader) are using the SAR ADC. This is the main change of this series: guarding all BL30 specific code with a corresponding "if"-block.

This also adds a new DT binding for the SAR ADC in Meson8b because the driver has to specify (for this older version) that there's no BL30 integration available (and these register bits should not be touched).

Martin Blumenstingl (2):
Documentation: dt-bindings: add a Meson8b compatible to the SAR ADC
iio: adc: meson-saradc: add Meson8b SoC compatibility

 .../bindings/iio/adc/amlogic,meson-saradc.txt      |  1 +
 drivers/iio/adc/meson_saradc.c                     | 70 ++++++++++++++--------
 2 files changed, 47 insertions(+), 24 deletions(-)
Signature · 1 line
2.12.1
author reviewer
#1 lore raw

PATCH 1/2 Documentation: dt-bindings: add a Meson8b compatible to the SAR ADC

The Amlogic Meson SAR ADC driver can be used on Meson8b as well (probably on earlier SoC generations as well, but I don't have any hardware available for testing that).
Add a separate compatible for Meson8b because it does not need any of the BL30 magic (unlike the GX SoCs).

---
 Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt +1 -0
index f9e3ff2c656e..84a931a0ff1f 100644
@@ -2,6 +2,7 @@
 
 Required properties:
 - compatible:	depending on the SoC this should be one of:
+			- "amlogic,meson8b-saradc" for Meson8b
 			- "amlogic,meson-gxbb-saradc" for GXBB
 			- "amlogic,meson-gxl-saradc" for GXL
 			- "amlogic,meson-gxm-saradc" for GXM
Signature · 1 line
2.12.1
maintainer
#2 lore raw

PATCH 1/2 Documentation: dt-bindings: add a Meson8b compatible to the SAR ADC

Quoted 10 lines · Martin Blumenstingl

The Amlogic Meson SAR ADC driver can be used on Meson8b as well (probably on earlier SoC generations as well, but I don't have any hardware available for testing that).
Add a separate compatible for Meson8b because it does not need any of the BL30 magic (unlike the GX SoCs).

---
 Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt | 1 +
 1 file changed, 1 insertion(+)

If you respin, "dt-bindings: iio: adc: ..." for the subject. Otherwise,

author reviewer
#3 lore raw

PATCH 2/2 iio: adc: meson-saradc: add Meson8b SoC compatibility

In reply to Martin Blumenstingl

Meson GX SoCs however use some magic bits to prevent simultaneous (= conflicting, because only consumer should use the FIFO buffer with the ADC results) usage by the Linux kernel and the bootloader (the BL30 bootloader uses the SAR ADC to read the CPU temperature). This patch changes guards all BL30 functionality so it is skipped on SoCs which don't have it. Since the hardware itself doesn't know whether BL30 is available the internal meson_sar_adc_data is extended so this information can be provided per of_device_id.data inside the driver.

Additionally the clocks "adc_clk" and "adc_sel" are not provided by the clock-controller itself. "adc_sel" is not available at all. "adc_clk" is provided by the SAR ADC IP block itself on Meson8b (and earlier). This is already supported by the meson_saradc driver.

Finally a new of_device_id for the Meson8b SoC is added so it can be wired up in the corresponding DT.

---
 drivers/iio/adc/meson_saradc.c | 70 +++++++++++++++++++++++++++---------------
 1 file changed, 46 insertions(+), 24 deletions(-)
drivers/iio/adc/meson_saradc.c +46 -24
index dd4190b50df6..f78fe66e0ec8 100644
@@ -220,6 +220,7 @@ enum meson_sar_adc_chan7_mux_sel {
 };
 
 struct meson_sar_adc_data {
+	char					has_bl30_integration;
 	unsigned int				resolution;
 	const char				*name;
 };
@@ -437,19 +438,24 @@ static int meson_sar_adc_lock(struct iio_dev *indio_dev)
 
 	mutex_lock(&indio_dev->mlock);
 
-	/* prevent BL30 from using the SAR ADC while we are using it */
-	regmap_update_bits(priv->regmap, MESON_SAR_ADC_DELAY,
-			   MESON_SAR_ADC_DELAY_KERNEL_BUSY,
-			   MESON_SAR_ADC_DELAY_KERNEL_BUSY);
-
-	/* wait until BL30 releases it's lock (so we can use the SAR ADC) */
-	do {
-		udelay(1);
-		regmap_read(priv->regmap, MESON_SAR_ADC_DELAY, &val);
-	} while (val & MESON_SAR_ADC_DELAY_BL30_BUSY && timeout--);
-
-	if (timeout < 0)
-		return -ETIMEDOUT;
+	if (priv->data->has_bl30_integration) {
+		/* prevent BL30 from using the SAR ADC while we are using it */
+		regmap_update_bits(priv->regmap, MESON_SAR_ADC_DELAY,
+				MESON_SAR_ADC_DELAY_KERNEL_BUSY,
+				MESON_SAR_ADC_DELAY_KERNEL_BUSY);
+
+		/*
+		 * wait until BL30 releases it's lock (so we can use the SAR
+		 * ADC)
+		 */
+		do {
+			udelay(1);
+			regmap_read(priv->regmap, MESON_SAR_ADC_DELAY, &val);
+		} while (val & MESON_SAR_ADC_DELAY_BL30_BUSY && timeout--);
+
+		if (timeout < 0)
+			return -ETIMEDOUT;
+	}
 
 	return 0;
 }
@@ -458,9 +464,10 @@ static void meson_sar_adc_unlock(struct iio_dev *indio_dev)
 {
 	struct meson_sar_adc_priv *priv = iio_priv(indio_dev);
 
-	/* allow BL30 to use the SAR ADC again */
-	regmap_update_bits(priv->regmap, MESON_SAR_ADC_DELAY,
-			   MESON_SAR_ADC_DELAY_KERNEL_BUSY, 0);
+	if (priv->data->has_bl30_integration)
+		/* allow BL30 to use the SAR ADC again */
+		regmap_update_bits(priv->regmap, MESON_SAR_ADC_DELAY,
+				MESON_SAR_ADC_DELAY_KERNEL_BUSY, 0);
 
 	mutex_unlock(&indio_dev->mlock);
 }
@@ -614,14 +621,16 @@ static int meson_sar_adc_init(struct iio_dev *indio_dev)
 	 */
 	meson_sar_adc_set_chan7_mux(indio_dev, CHAN7_MUX_CH7_INPUT);
 
-	/*
-	 * leave sampling delay and the input clocks as configured by BL30 to
-	 * make sure BL30 gets the values it expects when reading the
-	 * temperature sensor.
-	 */
-	regmap_read(priv->regmap, MESON_SAR_ADC_REG3, &regval);
-	if (regval & MESON_SAR_ADC_REG3_BL30_INITIALIZED)
-		return 0;
+	if (priv->data->has_bl30_integration) {
+		/*
+		 * leave sampling delay and the input clocks as configured by
+		 * BL30 to make sure BL30 gets the values it expects when
+		 * reading the temperature sensor.
+		 */
+		regmap_read(priv->regmap, MESON_SAR_ADC_REG3, &regval);
+		if (regval & MESON_SAR_ADC_REG3_BL30_INITIALIZED)
+			return 0;
+	}
 
 	meson_sar_adc_stop_sample_engine(indio_dev);
 
@@ -834,23 +843,36 @@ static const struct iio_info meson_sar_adc_iio_info = {
 	.driver_module = THIS_MODULE,
 };
 
+struct meson_sar_adc_data meson_sar_adc_meson8b_data = {
+	.has_bl30_integration = 0,
+	.resolution = 10,
+	.name = "meson-meson8b-saradc",
+};
+
 struct meson_sar_adc_data meson_sar_adc_gxbb_data = {
+	.has_bl30_integration = 1,
 	.resolution = 10,
 	.name = "meson-gxbb-saradc",
 };
 
 struct meson_sar_adc_data meson_sar_adc_gxl_data = {
+	.has_bl30_integration = 1,
 	.resolution = 12,
 	.name = "meson-gxl-saradc",
 };
 
 struct meson_sar_adc_data meson_sar_adc_gxm_data = {
+	.has_bl30_integration = 1,
 	.resolution = 12,
 	.name = "meson-gxm-saradc",
 };
 
 static const struct of_device_id meson_sar_adc_of_match[] = {
 	{
+		.compatible = "amlogic,meson8b-saradc",
+		.data = &meson_sar_adc_meson8b_data,
+	},
+	{
 		.compatible = "amlogic,meson-gxbb-saradc",
 		.data = &meson_sar_adc_gxbb_data,
 	}, {
Signature · 1 line
2.12.1
#4 lore raw

PATCH 2/2 iio: adc: meson-saradc: add Meson8b SoC compatibility

On Sat, 25 Mar 2017, Martin Blumenstingl wrote:

nitpicking below

Quoted 27 lines

Meson GX SoCs however use some magic bits to prevent simultaneous (= conflicting, because only consumer should use the FIFO buffer with the ADC results) usage by the Linux kernel and the bootloader (the BL30 bootloader uses the SAR ADC to read the CPU temperature). This patch changes guards all BL30 functionality so it is skipped on SoCs which don't have it. Since the hardware itself doesn't know whether BL30 is available the internal meson_sar_adc_data is extended so this information can be provided per of_device_id.data inside the driver.

Additionally the clocks "adc_clk" and "adc_sel" are not provided by the clock-controller itself. "adc_sel" is not available at all. "adc_clk" is provided by the SAR ADC IP block itself on Meson8b (and earlier). This is already supported by the meson_saradc driver.

Finally a new of_device_id for the Meson8b SoC is added so it can be wired up in the corresponding DT.

---
 drivers/iio/adc/meson_saradc.c | 70 +++++++++++++++++++++++++++---------------
 1 file changed, 46 insertions(+), 24 deletions(-)
drivers/iio/adc/meson_saradc.c +0 -0
index dd4190b50df6..f78fe66e0ec8 100644

drivers/iio/adc/meson_saradc.c enum meson_sar_adc_chan7_mux_sel { · line 223

Quoted 4 lines
drivers/iio/adc/meson_saradc.c +1 -0
@@ -220,6 +220,7 @@ enum meson_sar_adc_chan7_mux_sel {
 };
 
 struct meson_sar_adc_data {
+	char					has_bl30_integration;

bool?

Quoted 18 lines
drivers/iio/adc/meson_saradc.c +0 -11
 	unsigned int				resolution;
 	const char				*name;
 };
@@ -437,19 +438,24 @@ static int meson_sar_adc_lock(struct iio_dev *indio_dev)
 
 	mutex_lock(&indio_dev->mlock);
 
-	/* prevent BL30 from using the SAR ADC while we are using it */
-	regmap_update_bits(priv->regmap, MESON_SAR_ADC_DELAY,
-			   MESON_SAR_ADC_DELAY_KERNEL_BUSY,
-			   MESON_SAR_ADC_DELAY_KERNEL_BUSY);
-
-	/* wait until BL30 releases it's lock (so we can use the SAR ADC) */
-	do {
-		udelay(1);
-		regmap_read(priv->regmap, MESON_SAR_ADC_DELAY, &val);
-	} while (val & MESON_SAR_ADC_DELAY_BL30_BUSY && timeout--);
-

drivers/iio/adc/meson_saradc.c static int meson_sar_adc_lock(struct iio_dev *indio_dev) · line 448

Quoted 10 lines
drivers/iio/adc/meson_saradc.c +8 -2
-	if (timeout < 0)
-		return -ETIMEDOUT;
+	if (priv->data->has_bl30_integration) {
+		/* prevent BL30 from using the SAR ADC while we are using it */
+		regmap_update_bits(priv->regmap, MESON_SAR_ADC_DELAY,
+				MESON_SAR_ADC_DELAY_KERNEL_BUSY,
+				MESON_SAR_ADC_DELAY_KERNEL_BUSY);
+
+		/*
+		 * wait until BL30 releases it's lock (so we can use the SAR

its

Quoted 53 lines
drivers/iio/adc/meson_saradc.c +24 -11
+		 * ADC)
+		 */
+		do {
+			udelay(1);
+			regmap_read(priv->regmap, MESON_SAR_ADC_DELAY, &val);
+		} while (val & MESON_SAR_ADC_DELAY_BL30_BUSY && timeout--);
+
+		if (timeout < 0)
+			return -ETIMEDOUT;
+	}
 
 	return 0;
 }
@@ -458,9 +464,10 @@ static void meson_sar_adc_unlock(struct iio_dev *indio_dev)
 {
 	struct meson_sar_adc_priv *priv = iio_priv(indio_dev);
 
-	/* allow BL30 to use the SAR ADC again */
-	regmap_update_bits(priv->regmap, MESON_SAR_ADC_DELAY,
-			   MESON_SAR_ADC_DELAY_KERNEL_BUSY, 0);
+	if (priv->data->has_bl30_integration)
+		/* allow BL30 to use the SAR ADC again */
+		regmap_update_bits(priv->regmap, MESON_SAR_ADC_DELAY,
+				MESON_SAR_ADC_DELAY_KERNEL_BUSY, 0);
 
 	mutex_unlock(&indio_dev->mlock);
 }
@@ -614,14 +621,16 @@ static int meson_sar_adc_init(struct iio_dev *indio_dev)
 	 */
 	meson_sar_adc_set_chan7_mux(indio_dev, CHAN7_MUX_CH7_INPUT);
 
-	/*
-	 * leave sampling delay and the input clocks as configured by BL30 to
-	 * make sure BL30 gets the values it expects when reading the
-	 * temperature sensor.
-	 */
-	regmap_read(priv->regmap, MESON_SAR_ADC_REG3, &regval);
-	if (regval & MESON_SAR_ADC_REG3_BL30_INITIALIZED)
-		return 0;
+	if (priv->data->has_bl30_integration) {
+		/*
+		 * leave sampling delay and the input clocks as configured by
+		 * BL30 to make sure BL30 gets the values it expects when
+		 * reading the temperature sensor.
+		 */
+		regmap_read(priv->regmap, MESON_SAR_ADC_REG3, &regval);
+		if (regval & MESON_SAR_ADC_REG3_BL30_INITIALIZED)
+			return 0;
+	}
 
 	meson_sar_adc_stop_sample_engine(indio_dev);
 

drivers/iio/adc/meson_saradc.c static const struct iio_info meson_sar_adc_iio_info = { · line 847

Quoted 5 lines
drivers/iio/adc/meson_saradc.c +2 -0
@@ -834,23 +843,36 @@ static const struct iio_info meson_sar_adc_iio_info = {
 	.driver_module = THIS_MODULE,
 };
 
+struct meson_sar_adc_data meson_sar_adc_meson8b_data = {
+	.has_bl30_integration = 0,

= false

drivers/iio/adc/meson_saradc.c static const struct iio_info meson_sar_adc_iio_info = { · line 853

Quoted 6 lines
drivers/iio/adc/meson_saradc.c +5 -0
+	.resolution = 10,
+	.name = "meson-meson8b-saradc",
+};
+
 struct meson_sar_adc_data meson_sar_adc_gxbb_data = {
+	.has_bl30_integration = 1,

= true

Quoted 26 lines
drivers/iio/adc/meson_saradc.c +6 -0
 	.resolution = 10,
 	.name = "meson-gxbb-saradc",
 };
 
 struct meson_sar_adc_data meson_sar_adc_gxl_data = {
+	.has_bl30_integration = 1,
 	.resolution = 12,
 	.name = "meson-gxl-saradc",
 };
 
 struct meson_sar_adc_data meson_sar_adc_gxm_data = {
+	.has_bl30_integration = 1,
 	.resolution = 12,
 	.name = "meson-gxm-saradc",
 };
 
 static const struct of_device_id meson_sar_adc_of_match[] = {
 	{
+		.compatible = "amlogic,meson8b-saradc",
+		.data = &meson_sar_adc_meson8b_data,
+	},
+	{
 		.compatible = "amlogic,meson-gxbb-saradc",
 		.data = &meson_sar_adc_gxbb_data,
 	}, {
Signature · 2 lines
Peter Meerwald-Stadler
Mobile: +43 664 24 44 418
maintainer
#5 lore raw

PATCH 2/2 iio: adc: meson-saradc: add Meson8b SoC compatibility

In reply to Martin Blumenstingl
Quoted 14 lines · Martin Blumenstingl

Meson GX SoCs however use some magic bits to prevent simultaneous (= conflicting, because only consumer should use the FIFO buffer with the ADC results) usage by the Linux kernel and the bootloader (the BL30 bootloader uses the SAR ADC to read the CPU temperature). This patch changes guards all BL30 functionality so it is skipped on SoCs which don't have it. Since the hardware itself doesn't know whether BL30 is available the internal meson_sar_adc_data is extended so this information can be provided per of_device_id.data inside the driver.

Additionally the clocks "adc_clk" and "adc_sel" are not provided by the clock-controller itself. "adc_sel" is not available at all. "adc_clk" is provided by the SAR ADC IP block itself on Meson8b (and earlier). This is already supported by the meson_saradc driver.

Quoted 4 lines

Finally a new of_device_id for the Meson8b SoC is added so it can be wired up in the corresponding DT.

Looks sensible to me. Just fix those bits from Peter and we'll let it sit a few days on the list to see if anyone else wants to chip in.

Thanks,

Jonathan

Quoted 131 lines
---
 drivers/iio/adc/meson_saradc.c | 70 +++++++++++++++++++++++++++---------------
 1 file changed, 46 insertions(+), 24 deletions(-)
drivers/iio/adc/meson_saradc.c +46 -24
index dd4190b50df6..f78fe66e0ec8 100644
@@ -220,6 +220,7 @@ enum meson_sar_adc_chan7_mux_sel {
 };
 
 struct meson_sar_adc_data {
+	char					has_bl30_integration;
 	unsigned int				resolution;
 	const char				*name;
 };
@@ -437,19 +438,24 @@ static int meson_sar_adc_lock(struct iio_dev *indio_dev)
 
 	mutex_lock(&indio_dev->mlock);
 
-	/* prevent BL30 from using the SAR ADC while we are using it */
-	regmap_update_bits(priv->regmap, MESON_SAR_ADC_DELAY,
-			   MESON_SAR_ADC_DELAY_KERNEL_BUSY,
-			   MESON_SAR_ADC_DELAY_KERNEL_BUSY);
-
-	/* wait until BL30 releases it's lock (so we can use the SAR ADC) */
-	do {
-		udelay(1);
-		regmap_read(priv->regmap, MESON_SAR_ADC_DELAY, &val);
-	} while (val & MESON_SAR_ADC_DELAY_BL30_BUSY && timeout--);
-
-	if (timeout < 0)
-		return -ETIMEDOUT;
+	if (priv->data->has_bl30_integration) {
+		/* prevent BL30 from using the SAR ADC while we are using it */
+		regmap_update_bits(priv->regmap, MESON_SAR_ADC_DELAY,
+				MESON_SAR_ADC_DELAY_KERNEL_BUSY,
+				MESON_SAR_ADC_DELAY_KERNEL_BUSY);
+
+		/*
+		 * wait until BL30 releases it's lock (so we can use the SAR
+		 * ADC)
+		 */
+		do {
+			udelay(1);
+			regmap_read(priv->regmap, MESON_SAR_ADC_DELAY, &val);
+		} while (val & MESON_SAR_ADC_DELAY_BL30_BUSY && timeout--);
+
+		if (timeout < 0)
+			return -ETIMEDOUT;
+	}
 
 	return 0;
 }
@@ -458,9 +464,10 @@ static void meson_sar_adc_unlock(struct iio_dev *indio_dev)
 {
 	struct meson_sar_adc_priv *priv = iio_priv(indio_dev);
 
-	/* allow BL30 to use the SAR ADC again */
-	regmap_update_bits(priv->regmap, MESON_SAR_ADC_DELAY,
-			   MESON_SAR_ADC_DELAY_KERNEL_BUSY, 0);
+	if (priv->data->has_bl30_integration)
+		/* allow BL30 to use the SAR ADC again */
+		regmap_update_bits(priv->regmap, MESON_SAR_ADC_DELAY,
+				MESON_SAR_ADC_DELAY_KERNEL_BUSY, 0);
 
 	mutex_unlock(&indio_dev->mlock);
 }
@@ -614,14 +621,16 @@ static int meson_sar_adc_init(struct iio_dev *indio_dev)
 	 */
 	meson_sar_adc_set_chan7_mux(indio_dev, CHAN7_MUX_CH7_INPUT);
 
-	/*
-	 * leave sampling delay and the input clocks as configured by BL30 to
-	 * make sure BL30 gets the values it expects when reading the
-	 * temperature sensor.
-	 */
-	regmap_read(priv->regmap, MESON_SAR_ADC_REG3, &regval);
-	if (regval & MESON_SAR_ADC_REG3_BL30_INITIALIZED)
-		return 0;
+	if (priv->data->has_bl30_integration) {
+		/*
+		 * leave sampling delay and the input clocks as configured by
+		 * BL30 to make sure BL30 gets the values it expects when
+		 * reading the temperature sensor.
+		 */
+		regmap_read(priv->regmap, MESON_SAR_ADC_REG3, &regval);
+		if (regval & MESON_SAR_ADC_REG3_BL30_INITIALIZED)
+			return 0;
+	}
 
 	meson_sar_adc_stop_sample_engine(indio_dev);
 
@@ -834,23 +843,36 @@ static const struct iio_info meson_sar_adc_iio_info = {
 	.driver_module = THIS_MODULE,
 };
 
+struct meson_sar_adc_data meson_sar_adc_meson8b_data = {
+	.has_bl30_integration = 0,
+	.resolution = 10,
+	.name = "meson-meson8b-saradc",
+};
+
 struct meson_sar_adc_data meson_sar_adc_gxbb_data = {
+	.has_bl30_integration = 1,
 	.resolution = 10,
 	.name = "meson-gxbb-saradc",
 };
 
 struct meson_sar_adc_data meson_sar_adc_gxl_data = {
+	.has_bl30_integration = 1,
 	.resolution = 12,
 	.name = "meson-gxl-saradc",
 };
 
 struct meson_sar_adc_data meson_sar_adc_gxm_data = {
+	.has_bl30_integration = 1,
 	.resolution = 12,
 	.name = "meson-gxm-saradc",
 };
 
 static const struct of_device_id meson_sar_adc_of_match[] = {
 	{
+		.compatible = "amlogic,meson8b-saradc",
+		.data = &meson_sar_adc_meson8b_data,
+	},
+	{
 		.compatible = "amlogic,meson-gxbb-saradc",
 		.data = &meson_sar_adc_gxbb_data,
 	}, {
author reviewer
#6 lore raw

PATCH 2/2 iio: adc: meson-saradc: add Meson8b SoC compatibility

Quoted 15 lines · Jonathan Cameron
Quoted 14 lines · Martin Blumenstingl

Meson GX SoCs however use some magic bits to prevent simultaneous (= conflicting, because only consumer should use the FIFO buffer with the ADC results) usage by the Linux kernel and the bootloader (the BL30 bootloader uses the SAR ADC to read the CPU temperature). This patch changes guards all BL30 functionality so it is skipped on SoCs which don't have it. Since the hardware itself doesn't know whether BL30 is available the internal meson_sar_adc_data is extended so this information can be provided per of_device_id.data inside the driver.

Additionally the clocks "adc_clk" and "adc_sel" are not provided by the clock-controller itself. "adc_sel" is not available at all. "adc_clk" is provided by the SAR ADC IP block itself on Meson8b (and earlier). This is already supported by the meson_saradc driver.

Quoted 6 lines
Quoted 4 lines

Finally a new of_device_id for the Meson8b SoC is added so it can be wired up in the corresponding DT.

Looks sensible to me. Just fix those bits from Peter and we'll let it sit a few days on the list to see if anyone else wants to chip in.

OK, we'll have to wait for one of the DT-maintainers ACK (on the other patch) anyways, so I'll re-spin this in a week or so and fix everything that has come up until then

maintainer
#7 lore raw

PATCH 2/2 iio: adc: meson-saradc: add Meson8b SoC compatibility

Quoted 19 lines · Martin Blumenstingl
Quoted 18 lines · Jonathan Cameron
Quoted 17 lines · Martin Blumenstingl

Meson GX SoCs however use some magic bits to prevent simultaneous (= conflicting, because only consumer should use the FIFO buffer with the ADC results) usage by the Linux kernel and the bootloader (the BL30 bootloader uses the SAR ADC to read the CPU temperature). This patch changes guards all BL30 functionality so it is skipped on SoCs which don't have it. Since the hardware itself doesn't know whether BL30 is available the internal meson_sar_adc_data is extended so this information can be provided per of_device_id.data inside the driver.

Additionally the clocks "adc_clk" and "adc_sel" are not provided by the clock-controller itself. "adc_sel" is not available at all. "adc_clk" is provided by the SAR ADC IP block itself on Meson8b (and earlier). This is already supported by the meson_saradc driver.

Finally a new of_device_id for the Meson8b SoC is added so it can be wired up in the corresponding DT.

Quoted 6 lines
Quoted 3 lines
Quoted 1 line

Looks sensible to me. Just fix those bits from Peter and we'll let it sit a few days on the list to see if anyone else wants to chip in.

OK, we'll have to wait for one of the DT-maintainers ACK (on the other patch) anyways, so I'll re-spin this in a week or so and fix everything that has come up until then

There is some flexibility in 'trivial' dt bindings such as this so as not to waste their time. But we should allow them the opportunity before applying it anyway ;)

Jonathan

Quoted 5 lines

--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to majordomo at vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html