Skip to contentSkip to conversation

Please help for Data TLB Error in MPC8544

U-Boot duckycool 2 participants 5 messages May 21, 2009 – May 26, 2009

lore
Share & tools
lore

duckycool

author
#0 lore raw

Hi all,
My board can't boot normally, and I found it just hang in data tlb error through the system.map.
Could any one help for this?
Some regisers are as below:
============================================
DEAR: 0xf400fff0 (L1 init ram base address is 0xf4010000)
IVPR : 0xfff80000 , IVPR3: 0x000004000
EELADR: 0xf4010000 , CSn_BNDS: all 0x00000000 (I think SPD of DDR is not found yet)
L2MMU_TLB0 : 84000000 51000000 ff7000000 ff7000000 (CCSR is not relocated to 0xe0000000 yet)
============================================

The TLB1 registers from CodeWarrior is as below:
=================================================
L2MMU_CAM0 600007CA 1C080000 FFC00000 FFC000001 (boot flash, 4M) L2MMU_CAM1 A0007FCA 1C080000 80000000 800000001 (PCIE, 1G) L2MMU_CAM2 90003FCA 1C080000 C0000000 C00000001 (PCI, 256M) L2MMU_CAM3 90003FCA 1C080000 D0000000 D00000001 (PCI, 256M) L2MMU_CAM4 80001FCA 1C080000 E0000000 E00000001 (CCSR, 64M) L2MMU_CAM5 80001FCA 1C080000 F0000000 F00000001 (?? , 64M) L2MMU_CAM6 300000CA 18080000 FF040000 FF0400001 (NAND, 64K) L2MMU_CAM7 20000042 18080000 FF010000 FF0100001 (NAND, 16K) L2MMU_CAM8 20000042 18080000 FF050000 FF0500001 (NAND, 16K) L2MMU_CAM9 C87FD651 EB40000D 27DE6000 2397E000 L2MMU_CAM10 D0E2E2DF EB680009 B494F000 8F634000 L2MMU_CAM11 00FC8DCA 5A11000D BCB9B000 77EF6000 L2MMU_CAM12 300000CA 18080000 FF000000 FF000001 (NAND, 64K) L2MMU_CAM13 D891AFD8 18180002 50A70000 F7AB6000 L2MMU_CAM14 E0F6AE97 DA390009 F5DF6000 4F425000 L2MMU_CAM15 D8EFEF88 C750000F AEBA7000 3229F000
===================================================

And this is my init.s below:
==================================================================
#include <ppc_asm.tmpl>
#include <ppc_defs.h>
#include <asm/cache.h>
#include <asm/mmu.h>
#include <config.h>
#include <mpc85xx.h>

#define LAWAR_TRGT_PCI1 0x00000000

#define LAWAR_TRGT_PCIE1	             0x00200000
#define LAWAR_TRGT_PCIE2	             0x00100000
#define LAWAR_TRGT_PCIE3	             0x00300000

#define LAWAR_TRGT_LBC 0x00400000
#define LAWAR_TRGT_DDR 0x00f00000

#define	entry_start \
	mflr	r1	;	\
	bl	0f	;

#define entry_end \

0:	mflr	r0	;	\
	mtlr	r1	;	\
	blr		;


	.section	.bootpg, "ax"
	.globl	tlb1_entry
tlb1_entry:
	entry_start

	/*
	 * Number of TLB0 and TLB1 entries in the following table
	 */
	.long (2f-1f)/16
1:
	/*
	 * TLB0		4K	Non-cacheable, guarded
	 * 0xff700000	4K	Initial CCSRBAR mapping
	 *
	 * This ends up at a TLB0 Index==0 entry, and must not collide
	 * with other TLB0 Entries.
	 */
	.long TLB1_MAS0(0, 0, 0)
	.long TLB1_MAS1(1, 0, 0, 0, 0)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1)

	/*
	 * TLB0		16K	Cacheable, guarded
	 * Temporary Global data for initialization
	 *
	 * Use four 4K TLB0 entries.  These entries must be cacheable
	 * as they provide the bootstrap memory before the memory
	 * controler and real memory have been configured.
	 *
	 * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c,
	 * and must not collide with other TLB0 entries.
	 */
	.long TLB1_MAS0(0, 0, 0)
	.long TLB1_MAS1(1, 0, 0, 0, 0)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR),0,0,0,0,0,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR),0,0,0,0,0,1,0,1,0,1)

	.long TLB1_MAS0(0, 0, 0)
	.long TLB1_MAS1(1, 0, 0, 0, 0)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024),0,0,0,0,0,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 *

1024),0,0,0,0,0,1,0,1,0,1)

	.long TLB1_MAS0(0, 0, 0)
	.long TLB1_MAS1(1, 0, 0, 0, 0)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024),0,0,0,0,0,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 *

1024),0,0,0,0,0,1,0,1,0,1)

	.long TLB1_MAS0(0, 0, 0)
	.long TLB1_MAS1(1, 0, 0, 0, 0)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 *
1024),0,0,0,0,0,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 *

1024),0,0,0,0,0,1,0,1,0,1)

	/*
	 * TLB 0:	4M	Non-cacheable, guarded
	 * 0xffc00000	4M	Covers FLASH at 0xFFC00000
	 * Out of reset this entry is only 4K.
	 */
	.long TLB1_MAS0(1, 0, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_4M)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_BOOT_BLOCK), 0,0,0,0,1,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_BOOT_BLOCK), 0,0,0,0,0,1,0,1,0,1)

	/*
	 * TLB 1:	1G	Non-cacheable, guarded
	 * 0x80000000	1G	PCIE  8,9,a,b
	 */
	.long TLB1_MAS0(1, 1, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1G)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCIE_PHYS),0,0,0,0,1,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCIE_PHYS),0,0,0,0,0,1,0,1,0,1)
	

	/*
	 * TLB 2:	256M	Non-cacheable, guarded
	 */
	.long TLB1_MAS0(1, 2, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS),0,0,0,0,1,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS),0,0,0,0,0,1,0,1,0,1)
	 

	/*
	 * TLB 3:	256M	Non-cacheable, guarded
	 */
	.long TLB1_MAS0(1, 3, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS + 0x10000000),0,0,0,0,1,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS +

0x10000000),0,0,0,0,0,1,0,1,0,1)

	/*
	 * TLB 4:	64M	Non-cacheable, guarded
	 * 0xe000_0000	1M	CCSRBAR
	 * 0xe100_0000	255M	PCI IO range
	 */
	.long TLB1_MAS0(1, 4, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
	

	/*
	 * TLB 5:	64M	Non-cacheable, non-guarded , reserve from MPC8544DS (don't
know what is                                     it for)
	 */
	.long TLB1_MAS0(1, 5, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
	.long TLB1_MAS2(E500_TLB_EPN(0xf0000000), 0,0,0,0,0,0,0,0)
	.long TLB1_MAS3(E500_TLB_RPN(0xf0000000), 0,0,0,0,0,1,0,1,0,1)
	 

	/*
	 * TLB 6:	64K	Non-cacheable, guarded
	 * 0xff040000	64K	1G NAND flash 2 area 1 0xff040000
	 */
	.long TLB1_MAS0(1, 6, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64K)
	.long TLB1_MAS2(E500_TLB_EPN(0xff040000), 0,0,0,0,1,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(0xff040000), 0,0,0,0,0,0,0,1,0,1)
	

	/*
	 * TLB 7:	16K	Non-cacheable, guarded
	 * 0xff010000	16K	1G NAND flash 1 area 2 0xff010000
	 */
	.long TLB1_MAS0(1, 7, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16K)
	.long TLB1_MAS2(E500_TLB_EPN(0xff010000), 0,0,0,0,0,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(0xff010000), 0,0,0,0,0,0,0,1,0,1)
	

	/*
	 * TLB 8:	16K	Non-cacheable, guarded
	 * 0xff050000	16K	1G NAND flash 2 area 2 0xff050000
	 */
	.long TLB1_MAS0(1, 8, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16K)
	.long TLB1_MAS2(E500_TLB_EPN(0xff050000), 0,0,0,0,0,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(0xff050000), 0,0,0,0,0,0,0,1,0,1)
	 

	/*
	 * TLB 12:	64K	Non-cacheable, guarded
	 * 0xff000000	64K	1G NAND flash 1 area 1 0xff000000
	 */
	.long TLB1_MAS0(1, 12, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64K)
	.long TLB1_MAS2(E500_TLB_EPN(0xff000000), 0,0,0,0,1,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(0xff000000), 0,0,0,0,0,0,0,1,0,1)

2:
entry_end

/*
* LAW(Local Access Window) configuration:
*/

.section .bootpg, "ax"
.globl law_entry
law_entry:

	entry_start

	.long (4f-3f)/8
3:
	.long	0
	.long	LAWAR_EN | LAWAR_TRGT_DDR | (LAWAR_SIZE & LAWAR_SIZE_1G)

	.long	(CFG_PCI1_MEM_PHYS>>12) & 0xfffff
	.long	LAWAR_EN | LAWAR_TRGT_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M)

	.long	(CFG_PCI1_IO_PHYS>>12) & 0xfffff
	.long	LAWAR_EN | LAWAR_TRGT_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_64K)

	.long	(0xf0000000>>12) & 0xfffff
	.long	LAWAR_EN | LAWAR_TRGT_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M)

	.long	0
	.long	0

	.long	(CFG_PCIE1_IO_PHYS>>12) & 0xfffff
	.long	LAWAR_EN | LAWAR_TRGT_PCIE1 | (LAWAR_SIZE & LAWAR_SIZE_32G)

4:
entry_end
==============================================================================

What I think the problem might be
1. I didn't access the SPD to initial DDR , so failed ?
2. The TLB1_5 should take away ?
3. I shall add one more TLB for DDR ?
4. The real problem is not related with any above, and I shall post the other regisers for check ??

Thanks.

Signature · 2 lines
View this message in context: http://www.nabble.com/Please-help-for-Data-TLB-Error-in-MPC8544-tp23653353p23653353.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#1 lore raw
Quoted 6 lines

My board can't boot normally, and I found it just hang in data tlb error
through the system.map.
Could any one help for this?
Some regisers are as below:
============================================

Quoted 8 lines

DEAR: 0xf400fff0 (L1 init ram base address is 0xf4010000) IVPR : 0xfff80000 , IVPR3: 0x000004000
EELADR: 0xf4010000 , CSn_BNDS: all 0x00000000 (I think SPD of DDR is not
found yet)
L2MMU_TLB0 : 84000000 51000000 ff7000000 ff7000000 (CCSR is not relocated to
0xe0000000 yet)

EELADR - 0XF4010000, it is INIT_RAM address, why the transaction with address(0xF4010000) go to system bus?
It should keep in the cache due to cache lock, never out to system bus.

Quoted 241 lines

============================================

The TLB1 registers from CodeWarrior is as below:
=================================================
L2MMU_CAM0 600007CA 1C080000 FFC00000 FFC000001 (boot flash, 4M) L2MMU_CAM1 A0007FCA 1C080000 80000000 800000001 (PCIE, 1G) L2MMU_CAM2 90003FCA 1C080000 C0000000 C00000001 (PCI, 256M) L2MMU_CAM3 90003FCA 1C080000 D0000000 D00000001 (PCI, 256M) L2MMU_CAM4 80001FCA 1C080000 E0000000 E00000001 (CCSR, 64M) L2MMU_CAM5 80001FCA 1C080000 F0000000 F00000001 (?? , 64M) L2MMU_CAM6 300000CA 18080000 FF040000 FF0400001 (NAND, 64K) L2MMU_CAM7 20000042 18080000 FF010000 FF0100001 (NAND, 16K) L2MMU_CAM8 20000042 18080000 FF050000 FF0500001 (NAND, 16K) L2MMU_CAM9 C87FD651 EB40000D 27DE6000 2397E000 L2MMU_CAM10 D0E2E2DF EB680009 B494F000 8F634000 L2MMU_CAM11 00FC8DCA 5A11000D BCB9B000 77EF6000 L2MMU_CAM12 300000CA 18080000 FF000000 FF000001 (NAND, 64K) L2MMU_CAM13 D891AFD8 18180002 50A70000 F7AB6000 L2MMU_CAM14 E0F6AE97 DA390009 F5DF6000 4F425000 L2MMU_CAM15 D8EFEF88 C750000F AEBA7000 3229F000
===================================================

And this is my init.s below:
==================================================================
#include <ppc_asm.tmpl>
#include <ppc_defs.h>
#include <asm/cache.h>
#include <asm/mmu.h>
#include <config.h>
#include <mpc85xx.h>

#define LAWAR_TRGT_PCI1 0x00000000

#define LAWAR_TRGT_PCIE1	             0x00200000
#define LAWAR_TRGT_PCIE2	             0x00100000
#define LAWAR_TRGT_PCIE3	             0x00300000

#define LAWAR_TRGT_LBC 0x00400000
#define LAWAR_TRGT_DDR 0x00f00000

#define	entry_start \
	mflr	r1	;	\
	bl	0f	;

#define entry_end \

0:	mflr	r0	;	\
	mtlr	r1	;	\
	blr		;


	.section	.bootpg, "ax"
	.globl	tlb1_entry
tlb1_entry:
	entry_start

	/*
	 * Number of TLB0 and TLB1 entries in the following table
	 */
	.long (2f-1f)/16
1:
	/*
	 * TLB0		4K	Non-cacheable, guarded
	 * 0xff700000	4K	Initial CCSRBAR mapping
	 *
	 * This ends up at a TLB0 Index==0 entry, and must not collide
	 * with other TLB0 Entries.
	 */
	.long TLB1_MAS0(0, 0, 0)
	.long TLB1_MAS1(1, 0, 0, 0, 0)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 
0,0,0,0,1,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 

0,0,0,0,0,1,0,1,0,1)

/*
* TLB0 16K Cacheable, guarded
* Temporary Global data for initialization
*
* Use four 4K TLB0 entries. These entries must be cacheable
* as they provide the bootstrap memory before the memory
* controler and real memory have been configured. *
* These entries end up at TLB0 Indicies 0x10, 0x14,
0x18 and 0x1c,

	 * and must not collide with other TLB0 entries.
	 */
	.long TLB1_MAS0(0, 0, 0)
	.long TLB1_MAS1(1, 0, 0, 0, 0)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR),0,0,0,0,0,0,1,0)
	.long 

TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR),0,0,0,0,0,1,0,1,0,1)

	.long TLB1_MAS0(0, 0, 0)
	.long TLB1_MAS1(1, 0, 0, 0, 0)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 
1024),0,0,0,0,0,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 *

1024),0,0,0,0,0,1,0,1,0,1)

	.long TLB1_MAS0(0, 0, 0)
	.long TLB1_MAS1(1, 0, 0, 0, 0)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 
1024),0,0,0,0,0,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 *

1024),0,0,0,0,0,1,0,1,0,1)

	.long TLB1_MAS0(0, 0, 0)
	.long TLB1_MAS1(1, 0, 0, 0, 0)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 *
1024),0,0,0,0,0,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 *

1024),0,0,0,0,0,1,0,1,0,1)

	/*
	 * TLB 0:	4M	Non-cacheable, guarded
	 * 0xffc00000	4M	Covers FLASH at 0xFFC00000
	 * Out of reset this entry is only 4K.
	 */
	.long TLB1_MAS0(1, 0, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_4M)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_BOOT_BLOCK), 0,0,0,0,1,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_BOOT_BLOCK), 

0,0,0,0,0,1,0,1,0,1)

	/*
	 * TLB 1:	1G	Non-cacheable, guarded
	 * 0x80000000	1G	PCIE  8,9,a,b
	 */
	.long TLB1_MAS0(1, 1, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1G)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCIE_PHYS),0,0,0,0,1,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCIE_PHYS),0,0,0,0,0,1,0,1,0,1)
	

	/*
	 * TLB 2:	256M	Non-cacheable, guarded
	 */
	.long TLB1_MAS0(1, 2, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS),0,0,0,0,1,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS),0,0,0,0,0,1,0,1,0,1)
	 

	/*
	 * TLB 3:	256M	Non-cacheable, guarded
	 */
	.long TLB1_MAS0(1, 3, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS + 
0x10000000),0,0,0,0,1,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS +

0x10000000),0,0,0,0,0,1,0,1,0,1)

	/*
	 * TLB 4:	64M	Non-cacheable, guarded
	 * 0xe000_0000	1M	CCSRBAR
	 * 0xe100_0000	255M	PCI IO range
	 */
	.long TLB1_MAS0(1, 4, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
	

	/*
	 * TLB 5:	64M	Non-cacheable, non-guarded , 
reserve from MPC8544DS (don't
know what is                                     it for)
	 */
	.long TLB1_MAS0(1, 5, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
	.long TLB1_MAS2(E500_TLB_EPN(0xf0000000), 0,0,0,0,0,0,0,0)
	.long TLB1_MAS3(E500_TLB_RPN(0xf0000000), 0,0,0,0,0,1,0,1,0,1)
	 

	/*
	 * TLB 6:	64K	Non-cacheable, guarded
	 * 0xff040000	64K	1G NAND flash 2 area 1 0xff040000
	 */
	.long TLB1_MAS0(1, 6, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64K)
	.long TLB1_MAS2(E500_TLB_EPN(0xff040000), 0,0,0,0,1,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(0xff040000), 0,0,0,0,0,0,0,1,0,1)
	

	/*
	 * TLB 7:	16K	Non-cacheable, guarded
	 * 0xff010000	16K	1G NAND flash 1 area 2 0xff010000
	 */
	.long TLB1_MAS0(1, 7, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16K)
	.long TLB1_MAS2(E500_TLB_EPN(0xff010000), 0,0,0,0,0,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(0xff010000), 0,0,0,0,0,0,0,1,0,1)
	

	/*
	 * TLB 8:	16K	Non-cacheable, guarded
	 * 0xff050000	16K	1G NAND flash 2 area 2 0xff050000
	 */
	.long TLB1_MAS0(1, 8, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16K)
	.long TLB1_MAS2(E500_TLB_EPN(0xff050000), 0,0,0,0,0,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(0xff050000), 0,0,0,0,0,0,0,1,0,1)
	 

	/*
	 * TLB 12:	64K	Non-cacheable, guarded
	 * 0xff000000	64K	1G NAND flash 1 area 1 0xff000000
	 */
	.long TLB1_MAS0(1, 12, 0)
	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64K)
	.long TLB1_MAS2(E500_TLB_EPN(0xff000000), 0,0,0,0,1,0,1,0)
	.long TLB1_MAS3(E500_TLB_RPN(0xff000000), 0,0,0,0,0,0,0,1,0,1)

2:
entry_end

/*
* LAW(Local Access Window) configuration:
*/

.section .bootpg, "ax"
.globl law_entry
law_entry:

	entry_start

	.long (4f-3f)/8
3:
	.long	0
	.long	LAWAR_EN | LAWAR_TRGT_DDR | (LAWAR_SIZE & LAWAR_SIZE_1G)

	.long	(CFG_PCI1_MEM_PHYS>>12) & 0xfffff
	.long	LAWAR_EN | LAWAR_TRGT_PCI1 | (LAWAR_SIZE & 

LAWAR_SIZE_512M)

	.long	(CFG_PCI1_IO_PHYS>>12) & 0xfffff
	.long	LAWAR_EN | LAWAR_TRGT_PCI1 | (LAWAR_SIZE & 

LAWAR_SIZE_64K)

	.long	(0xf0000000>>12) & 0xfffff
	.long	LAWAR_EN | LAWAR_TRGT_LBC | (LAWAR_SIZE & 
Quoted 8 lines

LAWAR_SIZE_256M)

	.long	0
	.long	0

	.long	(CFG_PCIE1_IO_PHYS>>12) & 0xfffff
	.long	LAWAR_EN | LAWAR_TRGT_PCIE1 | (LAWAR_SIZE & 

LAWAR_SIZE_32G)

Why the PCIE1_IO have 32G space? It seems like one typo.

The u-boot version is very old, if you can post your start.S and board.h,
It will be helpful.

Thanks, Dave

author
#2 lore raw
Quoted 4 lines

EELADR - 0XF4010000, it is INIT_RAM address, why the transaction with address(0xF4010000) go to system bus?
It should keep in the cache due to cache lock, never out to system bus.

I don't know why... and it just happened.... shall I allocate a entry of tlb for it?? or cover it in some
space ?

Quoted 1 line

Why the PCIE1_IO have 32G space? It seems like one typo.

I reduce the size of PCIE1_IO and it doesn't help.

Quoted 1 line

The u-boot version is very old, if you can post your start.S and board.h,It

will be helpful.

Quoted 1 line

Thanks, Dave

I didn't change anything in start.s and I build it from the latest LTIB of mpc8544 of freescale.
But I did change memory map in board.h.

include/configs/mpc8544ds.h is as below:
==============================================================================
/*
* mpc8544ds board configuration file
*
*/
#ifndef __CONFIG_H
#define __CONFIG_H

/* High Level Configuration Options */
#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */
#define CONFIG_MPC8544 1
#define CONFIG_MPC8544DS 1

#define CONFIG_PCI 1 /* Enable PCI/PCIE */
#define CONFIG_PCI1 1 /* PCI controller 1 */
#define CONFIG_PCIE1 0 /* PCIE controler 1 (slot 1) */
#define CONFIG_PCIE2 0 /* PCIE controler 2 (slot 2) */
#define CONFIG_PCIE3 0 /* PCIE controler 3 (ULI bridge) */
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */

#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#undef CONFIG_DDR_DLL
#undef CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */

#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef

#define CONFIG_DDR_ECC_CMD
#undef CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */

/*
* When initializing flash, if we cannot find the manufacturer ID,
* assume this is the AMD flash associated with the CDS board.
* This allows booting from a promjet.
*/
#define CONFIG_ASSUME_AMD_FLASH

#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */

#ifndef __ASSEMBLY__
extern unsigned long get_board_sys_clk(unsigned long dummy); #endif
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */

/*
* These can be toggled for performance analysis, otherwise use default. */
#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
#undef CONFIG_CLEAR_LAW0 /* Clear LAW0 in cpu_init_r */

/*
* Only possible on E500 Version 2 or newer cores. */
#define CONFIG_ENABLE_36BIT_PHYS 1

#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */

#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
#define CFG_MEMTEST_END 0x00400000
#define CFG_ALT_MEMTEST
#define CONFIG_PANIC_HANG /* do not reset board on panic */

/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses) */
#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */

#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000)
#define CFG_PCIE2_ADDR (CFG_CCSRBAR+0x9000)
#define CFG_PCIE3_ADDR (CFG_CCSRBAR+0xb000)

/*
* DDR Setup
*/
#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE

#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */

/*
* Make sure required options are set
*/
#ifndef CONFIG_SPD_EEPROM
#error ("CONFIG_SPD_EEPROM is required")
#endif

#undef CONFIG_CLOCKS_IN_MHZ

/*
* Memory map
*
* 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
*
* 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
*
* 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
*
* 0xe000_0000 0xe00f_ffff CCSR 1M non-cacheable
* 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
*
* Localbus cacheable
*
* 0xf000_0000 0xf3ff_ffff SDRAM 64M Cacheable
* 0xf401_0000 0xf401_3fff L1 for stack 4K Cacheable TLB0
*
* Localbus non-cacheable
*
* 0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M non-cacheable
* 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M non-cacheable
* 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M non-cacheable
*
*/
#define CFG_64BIT_VSPRINTF 1
#define CFG_64BIT_STRTOUL 1

#define CFG_ID_EEPROM
#define ID_EEPROM_ADDR 0x57

/*
* Local Bus Definitions
*/
#define CFG_BOOT_BLOCK 0xffc00000 /* boot TLB */
#define CFG_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */
#define CFG_FLASH_BASE 0xffc00000 /* start of FLASH 4M */

#define CFG_BR0_PRELIM 0xffc01001
#define CFG_BR1_PRELIM 0xff000881

#define CFG_OR0_PRELIM 0xffc06e65 /*NAND Flash 1*/
#define CFG_OR1_PRELIM 0xfffe6000

#define CFG_BR3_PRELIM 0xff040881 /*NAND Flash 2*/
#define CFG_OR3_PRELIM 0xfffe6000

//#define CFG_FLASH_BANKS_LIST {0xfe800000,CFG_FLASH_BASE}

#define CFG_FLASH_QUIET_TEST
#define CFG_MAX_FLASH_BANKS 3 /* number of banks */
#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */

#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */

#define CFG_FLASH_CFI_DRIVER
#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO
/* #define CFG_FLASH_AMD_CHECK_DQ7 */
#define CFG_FLASH_AMD_CHECK_DATA_COMPARE

#define CFG_LBC_NONCACHE_BASE 0xf8000000

#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
#define PIXIS_BASE 0xf8100000 /* PIXIS registers */
#define PIXIS_ID 0x0 /* Board ID at offset 0 */
#define PIXIS_VER 0x1 /* Board version at offset 1 */
#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
#define PIXIS_RST 0x4 /* PIXIS Reset Control register */
#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch
* register */
#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
#define PIXIS_VCTL 0x10 /* VELA Control Register */
#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */

/* define to use L1 as initial stack */
#define CONFIG_L1_INIT_RAM 1
#define CFG_INIT_L1_LOCK 1
#define CFG_INIT_L1_ADDR 0xf4010000 /* Initial L1 address */
#define CFG_INIT_L1_END 0x00004000 /* End of used area in RAM */

/* define to use L2SRAM as initial stack */
#undef CONFIG_L2_INIT_RAM
#define CFG_INIT_L2_ADDR 0xf8fc0000
#define CFG_INIT_L2_END 0x00040000 /* End of used area in RAM */

#ifdef CONFIG_L1_INIT_RAM
#define CFG_INIT_RAM_ADDR CFG_INIT_L1_ADDR
#define CFG_INIT_RAM_END CFG_INIT_L1_END
#else
#define CFG_INIT_RAM_ADDR CFG_INIT_L2_ADDR
#define CFG_INIT_RAM_END CFG_INIT_L2_END
#endif

#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET

#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
#define CFG_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */

/* Serial Port - controlled on board with jumper J8
* open - index 2
* shorted - index 1
*/
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_NS16550
#define CFG_NS16550_SERIAL
#define CFG_NS16550_REG_SIZE 1
#define CFG_NS16550_CLK get_bus_freq(0)

#define CFG_BAUDRATE_TABLE	\
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}

#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)

/* Use the HUSH parser */
#define CFG_HUSH_PARSER
#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif

/* pass open firmware flat tree */
#define CONFIG_OF_FLAT_TREE 1
#define CONFIG_OF_BOARD_SETUP 1

#define OF_CPU "PowerPC,8544 at 0"
#define OF_SOC "soc8544 at e0000000"
#define OF_TBCLK (bd->bi_busfreq / 8)
#define OF_STDOUT_PATH "/soc8544 at e0000000/serial at 4500"

/* I2C */
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_EEPROM_ADDR 0x57
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
#define CFG_I2C_OFFSET 0x3100

/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0. */
#define CFG_PCIE_PHYS 0x80000000 /* 1G PCIE TLB */
#define CFG_PCI_PHYS 0xc0000000 /* 512M PCI TLB */

#define CFG_PCI1_MEM_BASE 0xc0000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
#define CFG_PCI1_IO_BASE 0x00000000
#define CFG_PCI1_IO_PHYS 0xe1000000
#define CFG_PCI1_IO_SIZE 0x00010000 /* 64k */

/* PCI view of System Memory */
#define CFG_PCI_MEMORY_BUS 0x00000000
#define CFG_PCI_MEMORY_PHYS 0x00000000
#define CFG_PCI_MEMORY_SIZE 0x80000000

/* controller 2, Slot 1, tgtid 1, Base address a000 */
#define CFG_PCIE2_MEM_BASE 0x0
#define CFG_PCIE2_MEM_PHYS CFG_PCIE2_MEM_BASE
#define CFG_PCIE2_MEM_SIZE 0x10000000 /* 256M */
#define CFG_PCIE2_IO_BASE 0x00000000
#define CFG_PCIE2_IO_PHYS 0x0
#define CFG_PCIE2_IO_SIZE 0x00000000 /* 64k */

/* controller 1, Slot 2,tgtid 2, Base address 8000 */
#define CFG_PCIE1_MEM_BASE 0x0
#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE
#define CFG_PCIE1_MEM_SIZE 0x20000000 /* 512M */
#define CFG_PCIE1_IO_BASE 0x00000000
#define CFG_PCIE1_IO_PHYS 0x0
#define CFG_PCIE1_IO_SIZE 0x00000000 /* 64k */

/* controller 3, direct to uli, tgtid 3, Base address b000 */
#define CFG_PCIE3_MEM_BASE 0xb0000000
#define CFG_PCIE3_MEM_PHYS CFG_PCIE3_MEM_BASE
#define CFG_PCIE3_MEM_SIZE 0x00100000 /* 1M */
#define CFG_PCIE3_IO_BASE 0x00000000
#define CFG_PCIE3_IO_PHYS 0xb0100000 /* reuse mem LAW */
#define CFG_PCIE3_IO_SIZE 0x00000000 /* 1M */
#define CFG_PCIE3_MEM_BASE2 0x0
#define CFG_PCIE3_MEM_PHYS2 CFG_PCIE3_MEM_BASE2
#define CFG_PCIE3_MEM_SIZE2 0x00000000 /* 1M */

#if defined(CONFIG_PCI)

/* video */
#define CONFIG_VIDEO

#if defined(CONFIG_VIDEO)
#define VIDEO_IO_OFFSET CFG_PCIE1_IO_PHYS
#define CONFIG_BIOSEMU
#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_ATI_RADEON_FB
#define CONFIG_VIDEO_LOGO

/*#define CONFIG_CONSOLE_CURSOR*/
#define CFG_ISA_IO_BASE_ADDRESS CFG_PCIE1_IO_PHYS
#endif

#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */

#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
#define CONFIG_RTL8139

#ifdef CONFIG_RTL8139
/* This macro is used by RTL8139 but not defined in PPC architecture */
#define KSEG1ADDR(x) ({u32 _x=le32_to_cpu(*(u32 *)(x)); (&_x);})
#define _IO_BASE 0x00000000
#endif

#ifndef CONFIG_PCI_PNP
	#define PCI_ENET0_IOADDR	CFG_PCI1_IO_BASE
	#define PCI_ENET0_MEMADDR	CFG_PCI1_IO_BASE
	#define PCI_IDSEL_NUMBER	0x11	/* IDSEL = AD11 */

#endif

#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_DOS_PARTITION
#define CONFIG_SCSI_AHCI

#ifdef CONFIG_SCSI_AHCI
#define CONFIG_SATA_ULI5288
#define CFG_SCSI_MAX_SCSI_ID 4
#define CFG_SCSI_MAX_LUN 1
#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
#endif /* SCSCI */

#endif /* CONFIG_PCI */

#if defined(CONFIG_TSEC_ENET)

#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI 1
#endif

#define CONFIG_SGMII_RISER
#define TSEC1_SGMII_PHY_ADDR_OFFSET 0x1c
#define CONFIG_TSEC_TBI
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "eTSEC1"
#define CONFIG_TSEC3 1
#define CONFIG_TSEC3_NAME "eTSEC3"

#define TSEC1_PHY_ADDR 0
#define TSEC3_PHY_ADDR 1

#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)

#define TSEC1_PHYIDX 0
#define TSEC3_PHYIDX 0

#define CONFIG_ETHPRIME "eTSEC1"

#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#endif /* CONFIG_TSEC_ENET */

/*
* Environment
*/
#define CFG_ENV_IS_IN_FLASH 1
#if CFG_MONITOR_BASE > 0xfff80000
#define CFG_ENV_ADDR 0xfff80000
#else
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x70000)
#endif
#define CFG_ENV_SIZE 0x2000
#define CFG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) */

#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */

/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME

/*
* Command line configuration.
*/
#include <config_cmd_default.h>

#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII

#if defined(CONFIG_PCI)
    #define CONFIG_CMD_PCI
    #define CONFIG_CMD_BEDBUG
    #define CONFIG_CMD_NET
    #define CONFIG_CMD_SCSI
    #define CONFIG_CMD_EXT2

#endif

#undef CONFIG_WATCHDOG /* watchdog disabled */

/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */

/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization. */
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/

/* Cache Configuration */
#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
#endif

/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif

/*
* Environment Configuration
*/

/* The mac addresses for all ethernet interface */ #if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH0
#define CONFIG_ETHADDR 00:E0:0C:02:00:FD
#define CONFIG_HAS_ETH1
#define CONFIG_ETH1ADDR 00:E0:0C:02:01:FD
#define CONFIG_HAS_ETH2
#define CONFIG_ETH2ADDR 00:E0:0C:02:02:FD
#define CONFIG_HAS_ETH3
#define CONFIG_ETH3ADDR 00:E0:0C:02:03:FD
#endif

#define CONFIG_IPADDR 192.168.1.251

#define CONFIG_HOSTNAME 8544ds_unknown
#define CONFIG_ROOTPATH /nfs/mpc85xx
#define CONFIG_BOOTFILE 8544ds/uImage.uboot
#define CONFIG_UBOOTPATH 8544ds/u-boot.bin /* TFTP server */

#define CONFIG_SERVERIP 192.168.0.1
#define CONFIG_GATEWAYIP 192.168.0.1
#define CONFIG_NETMASK 255.255.0.0

#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/

#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/

#define CONFIG_BAUDRATE 115200

#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3) #define PCIE_ENV \

 "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
	"echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
 "pcieerr=md ${a}020 1; md ${a}e00 e;"		\
	"pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"	\
	"pci d.w $b.0 56 1;"			\
	"pci d $b.0 104 1;pci d $b.0 110 1;pci d $b.0 130 1\0" \
 "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff;"	\
	"pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff;" \
	"pci w $b.0 104 ffffffff; pci w $b.0 110 ffffffff;" \
	"pci w $b.0 130 ffffffff\0" \

"pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \
"pcie1regs=setenv a e000a; run pciereg\0" \
"pcie2regs=setenv a e0009; run pciereg\0" \
"pcie3regs=setenv a e000b; run pciereg\0" \
"pcie1cfg=setenv b 3; run pciecfg\0" \
"pcie2cfg=setenv b 5; run pciecfg\0" \
"pcie3cfg=setenv b 0; run pciecfg\0" \
"pcie1err=setenv a e000a; setenv b 3; run pcieerr\0" \
"pcie2err=setenv a e0009; setenv b 5; run pcieerr\0" \
"pcie3err=setenv a e000b; setenv b 0; run pcieerr\0" \
"pcie1errc=setenv a e000a; setenv b 3; run pcieerrc\0" \
"pcie2errc=setenv a e0009; setenv b 5; run pcieerrc\0" \
"pcie3errc=setenv a e000b; setenv b 0; run pcieerrc\0"
#else
#define PCIE_ENV ""
#endif

#if defined(CONFIG_PCI1)
#define PCI_ENV \

 "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
	"echo e;md ${a}e00 9\0"			\
 "pci1regs=setenv a e0008; run pcireg\0"	\
 "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
	"pci d.w $b.0 56 1\0"			\
 "pcierrc=mw ${a}e00 ffffffff; mw ${a}e0c 0; pci w.b $b.0 7 ff;" \
	"pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff\0"		\

"pci1err=setenv a e0008; setenv b 7; run pcierr\0" \
"pci1errc=setenv a e0008; setenv b 7; run pcierrc\0"
#else
#define PCI_ENV ""
#endif

#if defined(CONFIG_TSEC_ENET)
#define ENET_ENV \

 "enetreg1=md ${a}000 2; md ${a}010 9; md ${a}050 4; md ${a}08c 1;" \
	"md ${a}098 2\0" \

"enetregt=echo t;md ${a}100 6; md ${a}140 2; md ${a}180 10; md ${a}200
10\0" \
"enetregr=echo r;md ${a}300 6; md ${a}330 5; md ${a}380 10; md ${a}400
10\0" \

 "enetregm=echo mac;md ${a}500 5; md ${a}520 28;echo fifo;md ${a}a00 1;" \
	"echo mib;md ${a}680 31\0" \

"enetreg=run enetreg1; run enetregm; run enetregt; run enetregr\0" \
"enet1regs=setenv a e0024; run enetreg\0" \
"enet3regs=setenv a e0026; run enetreg\0"
#else
#define ENET_ENV ""
#endif

#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \

 "tftpflash=tftpboot $loadaddr $uboot; "			\
	"protect off " MK_STR(TEXT_BASE) " +$filesize; "	\
	"erase " MK_STR(TEXT_BASE) " +$filesize; "		\
	"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; "	\
	"protect on " MK_STR(TEXT_BASE) " +$filesize; "		\
	"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0"	\
 "consoledev=ttyS0\0"				\
 "ramdiskaddr=2000000\0"			\
 "ramdiskfile=8544ds/ramdisk.uboot\0"		\
 "dtbaddr=c00000\0"				\
 "dtbfile=8544ds/mpc8544ds.dtb\0"		\
 "bdev=sda3\0"					\
 "eoi=mw e00400b0 0\0"				\
 "iack=md e00400a0 1\0"				\
 "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4; md ${a}bf0
4;" \
	"md ${a}e00 3; md ${a}e20 3; md ${a}e40 7; md ${a}f00 5\0" \
 "ddrregs=setenv a e0002; run ddrreg\0"		\
 "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}b20 3;" \
	"md ${a}e00 1; md ${a}e60 1; md ${a}ef0 15\0"	\

"guregs=setenv a e00e0; run gureg\0" \
"ecmreg=md ${a}000 1; md ${a}010 1; md ${a}bf8 2; md ${a}e00 6\0" \
"ecmregs=setenv a e0001; run ecmreg\0" \
"lawregs=md e0000c08 4b\0" \
"lbcregs=md e0005000 36\0" \
"dma0regs=md e0021100 12\0" \
"dma1regs=md e0021180 12\0" \
"dma2regs=md e0021200 12\0" \
"dma3regs=md e0021280 12\0" \
PCIE_ENV \
PCI_ENV \
ENET_ENV

#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $dtbaddr $dtbfile;" \
"bootm $loadaddr - $dtbaddr"

#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
"tftp $dtbaddr $dtbfile;" \
"bootm $loadaddr $ramdiskaddr $dtbaddr"

#define CONFIG_BOOTCOMMAND \
"setenv bootargs root=/dev/$bdev rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $dtbaddr $dtbfile;" \
"bootm $loadaddr - $dtbaddr"

#endif /* __CONFIG_H */
=============================================================================

the cpu/mpc85xx/start.s is as below:
============================================================================
/* U-Boot Startup Code for Motorola 85xx PowerPC based Embedded Boards
*
* The processor starts@0xfffffffc and the code is first executed in the
* last 4K page(0xfffff000-0xffffffff) in flash/rom.
*
*/

#include <config.h>
#include <mpc85xx.h>
#include <version.h>

#define _LINUX_CONFIG_H 1 /* avoid reading Linux autoconf.h file */

#include <ppc_asm.tmpl>
#include <ppc_defs.h>

#include <asm/cache.h>
#include <asm/mmu.h>

#ifndef CONFIG_IDENT_STRING
#define CONFIG_IDENT_STRING ""
#endif

#undef MSR_KERNEL
#define MSR_KERNEL ( MSR_ME ) /* Machine Check */

/*
* Set up GOT: Global Offset Table
*
* Use r14 to access the GOT
*/

	START_GOT
	GOT_ENTRY(_GOT2_TABLE_)
	GOT_ENTRY(_FIXUP_TABLE_)

	GOT_ENTRY(_start)
	GOT_ENTRY(_start_of_vectors)
	GOT_ENTRY(_end_of_vectors)
	GOT_ENTRY(transfer_to_handler)

	GOT_ENTRY(__init_end)
	GOT_ENTRY(_end)
	GOT_ENTRY(__bss_start)
	END_GOT

/*
* e500 Startup -- after reset only the last 4KB of the effective
* address space is mapped in the MMU L2 TLB1 Entry0. The .bootpg
* section is located at THIS LAST page and basically does three
* things: clear some registers, set up exception tables and
* add more TLB entries for 'larger spaces'(e.g. the boot rom) to
* continue the boot procedure.

* Once the boot rom is mapped by TLB entries we can proceed
* with normal startup.
*
*/

	.section .bootpg,"ax"
	.globl _start_e500

_start_e500:

/* clear registers/arrays not reset by hardware */

	/* L1 */
	li	r0,2
	mtspr	L1CSR0,r0	/* invalidate d-cache */
	mtspr	L1CSR1,r0 	/* invalidate i-cache */

	mfspr	r1,DBSR
	mtspr	DBSR,r1		/* Clear all valid bits */

	/*
	 *	Enable L1 Caches early
	 *
	 */

	lis	r2,L1CSR0_CPE at H	/* enable parity */
	ori	r2,r2,L1CSR0_DCE
	mtspr	L1CSR0,r2	/* enable L1 Dcache */
	isync
	mtspr	L1CSR1,r2	/* enable L1 Icache */
	isync
	msync

	/* Setup interrupt vectors */
	lis	r1,TEXT_BASE at h
	mtspr	IVPR,r1

	li	r1,0x0100
	mtspr	IVOR0,r1	/* 0: Critical input */
	li	r1,0x0200
	mtspr	IVOR1,r1	/* 1: Machine check */
	li	r1,0x0300
	mtspr	IVOR2,r1	/* 2: Data storage */
	li	r1,0x0400
	mtspr	IVOR3,r1	/* 3: Instruction storage */
	li	r1,0x0500
	mtspr	IVOR4,r1	/* 4: External interrupt */
	li	r1,0x0600
	mtspr	IVOR5,r1	/* 5: Alignment */
	li	r1,0x0700
	mtspr	IVOR6,r1	/* 6: Program check */
	li	r1,0x0800
	mtspr	IVOR7,r1	/* 7: floating point unavailable */
	li	r1,0x0900
	mtspr	IVOR8,r1	/* 8: System call */
	/* 9: Auxiliary processor unavailable(unsupported) */
	li	r1,0x0a00
	mtspr	IVOR10,r1	/* 10: Decrementer */
	li	r1,0x0b00
	mtspr	IVOR11,r1	/* 11: Interval timer */
	li	r1,0x0c00
	mtspr	IVOR12,r1	/* 12: Watchdog timer */
	li	r1,0x0d00
	mtspr	IVOR13,r1	/* 13: Data TLB error */
	li	r1,0x0e00
	mtspr	IVOR14,r1	/* 14: Instruction TLB error */
	li	r1,0x0f00
	mtspr	IVOR15,r1	/* 15: Debug */


	/*
	 * After reset, CCSRBAR is located at CFG_CCSRBAR_DEFAULT, i.e.
	 * 0xff700000-0xff800000. We need add a TLB1 entry for this 1MB
	 * region before we can access any CCSR registers such as L2
	 * registers, Local Access Registers,etc. We will also re-allocate
	 * CFG_CCSRBAR_DEFAULT to CFG_CCSRBAR immediately after TLB1 setup.
	 *
	 * Please refer to board-specif directory for TLB1 entry configuration.
	 * (e.g. board/<yourboard>/init.S)
	 *
	 */
	bl	tlb1_entry
	mr	r5,r0
	lwzu	r4,0(r5)	/* how many TLB1 entries we actually use */
	mtctr	r4

0: lwzu r6,4(r5)

	lwzu	r7,4(r5)
	lwzu	r8,4(r5)
	lwzu	r9,4(r5)
	mtspr	MAS0,r6
	mtspr	MAS1,r7
	mtspr	MAS2,r8
	mtspr	MAS3,r9
	isync
	msync
	tlbwe
	isync
	bdnz	0b

1:

#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
	/* Special sequence needed to update CCSRBAR itself */
	lis	r4,CFG_CCSRBAR_DEFAULT at h
	ori	r4,r4,CFG_CCSRBAR_DEFAULT at l

	lis	r5,CFG_CCSRBAR at h
	ori	r5,r5,CFG_CCSRBAR at l
	srwi	r6,r5,12
	stw	r6,0(r4)
	isync

	lis	r5,0xffff
	ori	r5,r5,0xf000
	lwz	r5,0(r5)
	isync

	lis	r3,CFG_CCSRBAR at h
	lwz	r5,CFG_CCSRBAR at l(r3)
	isync

#endif

	/* set up local access windows, defined at board/<boardname>/init.S */
	lis	r7,CFG_CCSRBAR at h
	ori	r7,r7,CFG_CCSRBAR at l

	bl	law_entry
	mr	r6,r0
	lwzu	r5,0(r6)	/* how many windows we actually use */
	mtctr	r5

	li	r2,0x0c28	/* the first pair is reserved for */
	li	r1,0x0c30	/* boot-over-rio-or-pci */

0: lwzu r4,4(r6)

	lwzu	r3,4(r6)
	stwx	r4,r7,r2
	stwx	r3,r7,r1
	addi	r2,r2,0x0020
	addi	r1,r1,0x0020
	bdnz	0b

	/* Clear and set up some registers. */
	li	r0,0x0000
	lis	r1,0xffff
	mtspr	DEC,r0			/* prevent dec exceptions */
	mttbl	r0			/* prevent fit & wdt exceptions */
	mttbu	r0
	mtspr	TSR,r1			/* clear all timer exception status */
	mtspr	TCR,r0			/* disable all */
	mtspr	ESR,r0			/* clear exception syndrome register */
	mtspr	MCSR,r0			/* machine check syndrome register */
	mtxer	r0			/* clear integer exception register */
	lis	r1,0x0002		/* set CE bit (Critical Exceptions) */
	ori	r1,r1,0x1200		/* set ME/DE bit */
	mtmsr	r1			/* change MSR */
	isync

	/* Enable Time Base and Select Time Base Clock */
	lis	r0,HID0_EMCP at h		/* Enable machine check */
#if defined(CONFIG_ENABLE_36BIT_PHYS)
	ori	r0,r0,(HID0_TBEN|HID0_ENMAS7)@l	/* Enable Timebase & MAS7 */
#else
	ori	r0,r0,HID0_TBEN at l	/* enable Timebase */
#endif
	mtspr	HID0,r0

	li	r0,(HID1_ASTME|HID1_ABE)@l	/* Addr streaming & broadcast */
	mtspr	HID1,r0

	/* Enable Branch Prediction */
#if defined(CONFIG_BTB)
	li	r0,0x201		/* BBFI = 1, BPEN = 1 */
	mtspr	BUCSR,r0

#endif

#if defined(CFG_INIT_DBCR)
	lis	r1,0xffff
	ori	r1,r1,0xffff
	mtspr	DBSR,r1			/* Clear all status bits */
	lis	r0,CFG_INIT_DBCR at h	/* DBCR0[IDM] must be set */
	ori	r0,r0,CFG_INIT_DBCR at l
	mtspr	DBCR0,r0

#endif

/* L1 DCache is used for initial RAM */

	/* Allocate Initial RAM in data cache.
	 */
	lis	r3,CFG_INIT_RAM_ADDR at h
	ori	r3,r3,CFG_INIT_RAM_ADDR at l
	li	r2,512 /* 512*32=16K */
	mtctr	r2
	li	r0,0
1:
	dcbz	r0,r3
	dcbtls	0,r0,r3
	addi	r3,r3,32
	bdnz	1b

	/* Jump out the last 4K page and continue to 'normal' start */
#ifdef CFG_RAMBOOT
	bl	3f
	b	_start_cont
#else
	/* Calculate absolute address in FLASH and jump there		*/
	/*--------------------------------------------------------------*/
	lis	r3,CFG_MONITOR_BASE at h
	ori	r3,r3,CFG_MONITOR_BASE at l
	addi	r3,r3,_start_cont - _start + _START_OFFSET
	mtlr	r3

#endif

3: li r0,0
#if !defined(CONFIG_CW)
mtspr SRR1,r0 /* Keep things disabled for now */

#endif
	mflr	r1
	mtspr	SRR0,r1
	rfi
	isync

	.text
	.globl	_start
_start:
	.long	0x27051956		/* U-BOOT Magic Number */
	.globl	version_string
version_string:
	.ascii U_BOOT_VERSION
	.ascii " (", __DATE__, " - ", __TIME__, ")"
	.ascii CONFIG_IDENT_STRING, "\0"

	.align	4
	.globl	_start_cont
_start_cont:
	/* Setup the stack in initial RAM,could be L2-as-SRAM or L1 dcache*/
	lis	r1,CFG_INIT_RAM_ADDR at h
	ori	r1,r1,CFG_INIT_SP_OFFSET at l

	li	r0,0
	stwu	r0,-4(r1)
	stwu	r0,-4(r1)		/* Terminate call chain */

	stwu	r1,-8(r1)		/* Save back chain and move SP */
	lis	r0,RESET_VECTOR at h	/* Address of reset vector */
	ori	r0,r0,RESET_VECTOR at l
	stwu	r1,-8(r1)		/* Save back chain and move SP */
	stw	r0,+12(r1)		/* Save return addr (underflow vect) */

	GET_GOT
	bl	cpu_init_f
	bl	board_init_f
	isync

	. = EXC_OFF_SYS_RESET
	.globl	_start_of_vectors

_start_of_vectors:

/* Critical input. */

	CRIT_EXCEPTION(0x0100, CriticalInput, CritcalInputException)

/* Machine check */

	MCK_EXCEPTION(0x200, MachineCheck, MachineCheckException)

/* Data Storage exception. */

	STD_EXCEPTION(0x0300, DataStorage, UnknownException)

/* Instruction Storage exception. */

	STD_EXCEPTION(0x0400, InstStorage, UnknownException)

/* External Interrupt exception. */

	STD_EXCEPTION(0x0500, ExtInterrupt, ExtIntException)

/* Alignment exception. */

	. = 0x0600
Alignment:
	EXCEPTION_PROLOG(SRR0, SRR1)
	mfspr	r4,DAR
	stw	r4,_DAR(r21)
	mfspr	r5,DSISR
	stw	r5,_DSISR(r21)
	addi	r3,r1,STACK_FRAME_OVERHEAD
	li	r20,MSR_KERNEL
	rlwimi	r20,r23,0,16,16		/* copy EE bit from saved MSR */
	lwz	r6,GOT(transfer_to_handler)
	mtlr	r6
	blrl

.L_Alignment:
.long AlignmentException - _start + _START_OFFSET
.long int_return - _start + _START_OFFSET

/* Program check exception */

	. = 0x0700
ProgramCheck:
	EXCEPTION_PROLOG(SRR0, SRR1)
	addi	r3,r1,STACK_FRAME_OVERHEAD
	li	r20,MSR_KERNEL
	rlwimi	r20,r23,0,16,16		/* copy EE bit from saved MSR */
	lwz	r6,GOT(transfer_to_handler)
	mtlr	r6
	blrl
.L_ProgramCheck:
	.long	ProgramCheckException - _start + _START_OFFSET
	.long	int_return - _start + _START_OFFSET

	/* No FPU on MPC85xx.  This exception is not supposed to happen.
	*/
	STD_EXCEPTION(0x0800, FPUnavailable, UnknownException)

	. = 0x0900

/*
* r0 - SYSCALL number
* r3-... arguments
*/
SystemCall:

	addis	r11,r0,0	/* get functions table addr */
	ori	r11,r11,0	/* Note: this code is patched in trap_init */
	addis	r12,r0,0	/* get number of functions */
	ori	r12,r12,0

	cmplw	0,r0,r12
	bge	1f

	rlwinm	r0,r0,2,0,31	/* fn_addr = fn_tbl[r0] */
	add	r11,r11,r0
	lwz	r11,0(r11)

	li	r20,0xd00-4	/* Get stack pointer */
	lwz	r12,0(r20)
	subi	r12,r12,12	/* Adjust stack pointer */
	li	r0,0xc00+_end_back-SystemCall
	cmplw	0,r0,r12	/* Check stack overflow */
	bgt	1f
	stw	r12,0(r20)

	mflr	r0
	stw	r0,0(r12)
	mfspr	r0,SRR0
	stw	r0,4(r12)
	mfspr	r0,SRR1
	stw	r0,8(r12)

	li	r12,0xc00+_back-SystemCall
	mtlr	r12
	mtspr	SRR0,r11

1: SYNC
rfi
_back:

	mfmsr	r11			/* Disable interrupts */
	li	r12,0
	ori	r12,r12,MSR_EE
	andc	r11,r11,r12
	SYNC				/* Some chip revs need this... */
	mtmsr	r11
	SYNC

	li	r12,0xd00-4		/* restore regs */
	lwz	r12,0(r12)

	lwz	r11,0(r12)
	mtlr	r11
	lwz	r11,4(r12)
	mtspr	SRR0,r11
	lwz	r11,8(r12)
	mtspr	SRR1,r11

	addi	r12,r12,12		/* Adjust stack pointer */
	li	r20,0xd00-4
	stw	r12,0(r20)

	SYNC
	rfi

_end_back:

	STD_EXCEPTION(0x0a00, Decrementer, timer_interrupt)
	STD_EXCEPTION(0x0b00, IntervalTimer, UnknownException)
	STD_EXCEPTION(0x0c00, WatchdogTimer, UnknownException)

	STD_EXCEPTION(0x0d00, DataTLBError, UnknownException)
	STD_EXCEPTION(0x0e00, InstructionTLBError, UnknownException)

	CRIT_EXCEPTION(0x0f00, DebugBreakpoint, DebugException )

	.globl	_end_of_vectors

_end_of_vectors:

	. = . + (0x100 - ( . & 0xff ))	/* align for debug */

/*
* This code finishes saving the registers to the exception frame
* and jumps to the appropriate handler for the exception.
* Register r21 is pointer into trap frame, r1 has new stack pointer. */
.globl transfer_to_handler
transfer_to_handler:

	stw	r22,_NIP(r21)
	lis	r22,MSR_POW at h
	andc	r23,r23,r22
	stw	r23,_MSR(r21)
	SAVE_GPR(7, r21)
	SAVE_4GPRS(8, r21)
	SAVE_8GPRS(12, r21)
	SAVE_8GPRS(24, r21)

	mflr	r23
	andi.	r24,r23,0x3f00		/* get vector offset */
	stw	r24,TRAP(r21)
	li	r22,0
	stw	r22,RESULT(r21)
	mtspr	SPRG2,r22		/* r1 is now kernel sp */

	lwz	r24,0(r23)		/* virtual address of handler */
	lwz	r23,4(r23)		/* where to go when done */
	mtspr	SRR0,r24
	mtspr	SRR1,r20
	mtlr	r23
	SYNC
	rfi				/* jump to handler, enable MMU */

int_return:

	mfmsr	r28		/* Disable interrupts */
	li	r4,0
	ori	r4,r4,MSR_EE
	andc	r28,r28,r4
	SYNC			/* Some chip revs need this... */
	mtmsr	r28
	SYNC
	lwz	r2,_CTR(r1)
	lwz	r0,_LINK(r1)
	mtctr	r2
	mtlr	r0
	lwz	r2,_XER(r1)
	lwz	r0,_CCR(r1)
	mtspr	XER,r2
	mtcrf	0xFF,r0
	REST_10GPRS(3, r1)
	REST_10GPRS(13, r1)
	REST_8GPRS(23, r1)
	REST_GPR(31, r1)
	lwz	r2,_NIP(r1)	/* Restore environment */
	lwz	r0,_MSR(r1)
	mtspr	SRR0,r2
	mtspr	SRR1,r0
	lwz	r0,GPR0(r1)
	lwz	r2,GPR2(r1)
	lwz	r1,GPR1(r1)
	SYNC
	rfi

crit_return:

	mfmsr	r28		/* Disable interrupts */
	li	r4,0
	ori	r4,r4,MSR_EE
	andc	r28,r28,r4
	SYNC			/* Some chip revs need this... */
	mtmsr	r28
	SYNC
	lwz	r2,_CTR(r1)
	lwz	r0,_LINK(r1)
	mtctr	r2
	mtlr	r0
	lwz	r2,_XER(r1)
	lwz	r0,_CCR(r1)
	mtspr	XER,r2
	mtcrf	0xFF,r0
	REST_10GPRS(3, r1)
	REST_10GPRS(13, r1)
	REST_8GPRS(23, r1)
	REST_GPR(31, r1)
	lwz	r2,_NIP(r1)	/* Restore environment */
	lwz	r0,_MSR(r1)
	mtspr	SPRN_CSRR0,r2
	mtspr	SPRN_CSRR1,r0
	lwz	r0,GPR0(r1)
	lwz	r2,GPR2(r1)
	lwz	r1,GPR1(r1)
	SYNC
	rfci

mck_return:

	mfmsr	r28		/* Disable interrupts */
	li	r4,0
	ori	r4,r4,MSR_EE
	andc	r28,r28,r4
	SYNC			/* Some chip revs need this... */
	mtmsr	r28
	SYNC
	lwz	r2,_CTR(r1)
	lwz	r0,_LINK(r1)
	mtctr	r2
	mtlr	r0
	lwz	r2,_XER(r1)
	lwz	r0,_CCR(r1)
	mtspr	XER,r2
	mtcrf	0xFF,r0
	REST_10GPRS(3, r1)
	REST_10GPRS(13, r1)
	REST_8GPRS(23, r1)
	REST_GPR(31, r1)
	lwz	r2,_NIP(r1)	/* Restore environment */
	lwz	r0,_MSR(r1)
	mtspr	SPRN_MCSRR0,r2
	mtspr	SPRN_MCSRR1,r0
	lwz	r0,GPR0(r1)
	lwz	r2,GPR2(r1)
	lwz	r1,GPR1(r1)
	SYNC
	rfmci

/* Cache functions.
*/
invalidate_icache:

	mfspr	r0,L1CSR1
	ori	r0,r0,L1CSR1_ICFI
	msync
	isync
	mtspr	L1CSR1,r0
	isync
	blr				/* entire I cache */

invalidate_dcache:

	mfspr	r0,L1CSR0
	ori	r0,r0,L1CSR0_DCFI
	msync
	isync
	mtspr	L1CSR0,r0
	isync
	blr

	.globl	icache_enable
icache_enable:
	mflr	r8
	bl	invalidate_icache
	mtlr	r8
	isync
	mfspr	r4,L1CSR1
	ori	r4,r4,0x0001
	oris	r4,r4,0x0001
	mtspr	L1CSR1,r4
	isync
	blr

	.globl	icache_disable
icache_disable:
	mfspr	r0,L1CSR1
	lis	r3,0
	ori	r3,r3,L1CSR1_ICE
	andc	r0,r0,r3
	mtspr	L1CSR1,r0
	isync
	blr

	.globl	icache_status
icache_status:
	mfspr	r3,L1CSR1
	andi.	r3,r3,L1CSR1_ICE
	blr

	.globl	dcache_enable
dcache_enable:
	mflr	r8
	bl	invalidate_dcache
	mtlr	r8
	isync
	mfspr	r0,L1CSR0
	ori	r0,r0,0x0001
	oris	r0,r0,0x0001
	msync
	isync
	mtspr	L1CSR0,r0
	isync
	blr

	.globl	dcache_disable
dcache_disable:
	mfspr	r3,L1CSR0
	lis	r4,0
	ori	r4,r4,L1CSR0_DCE
	andc	r3,r3,r4
	mtspr	L1CSR0,r0
	isync
	blr

	.globl	dcache_status
dcache_status:
	mfspr	r3,L1CSR0
	andi.	r3,r3,L1CSR0_DCE
	blr

	.globl get_pir

get_pir:
mfspr r3,PIR
blr

.globl get_pvr
get_pvr:
mfspr r3,PVR
blr

.globl get_svr
get_svr:
mfspr r3,SVR
blr

.globl wr_tcr
wr_tcr:
mtspr TCR,r3
blr

/*------------------------------------------------------------------------------- */
/* Function: in8 */
/* Description: Input 8 bits */
/*------------------------------------------------------------------------------- */

	.globl	in8
in8:
	lbz	r3,0x0000(r3)
	blr

/*------------------------------------------------------------------------------- */
/* Function: out8 */
/* Description: Output 8 bits */
/*------------------------------------------------------------------------------- */

	.globl	out8
out8:
	stb	r4,0x0000(r3)
	blr

/*------------------------------------------------------------------------------- */
/* Function: out16 */
/* Description: Output 16 bits */
/*------------------------------------------------------------------------------- */

	.globl	out16
out16:
	sth	r4,0x0000(r3)
	blr

/*------------------------------------------------------------------------------- */
/* Function: out16r */
/* Description: Byte reverse and output 16 bits */
/*------------------------------------------------------------------------------- */

	.globl	out16r
out16r:
	sthbrx	r4,r0,r3
	blr

/*------------------------------------------------------------------------------- */
/* Function: out32 */
/* Description: Output 32 bits */
/*------------------------------------------------------------------------------- */

	.globl	out32
out32:
	stw	r4,0x0000(r3)
	blr

/*------------------------------------------------------------------------------- */
/* Function: out32r */
/* Description: Byte reverse and output 32 bits */
/*------------------------------------------------------------------------------- */

	.globl	out32r
out32r:
	stwbrx	r4,r0,r3
	blr

/*------------------------------------------------------------------------------- */
/* Function: in16 */
/* Description: Input 16 bits */
/*------------------------------------------------------------------------------- */

	.globl	in16
in16:
	lhz	r3,0x0000(r3)
	sync
	blr

/*------------------------------------------------------------------------------- */
/* Function: in16r */
/* Description: Input 16 bits and byte reverse */
/*------------------------------------------------------------------------------- */

	.globl	in16r
in16r:
	lhbrx	r3,r0,r3
	sync
	blr

/*------------------------------------------------------------------------------- */
/* Function: in32 */
/* Description: Input 32 bits */
/*------------------------------------------------------------------------------- */

	.globl	in32
in32:
	lwz	3,0x0000(3)
	sync
	blr

/*------------------------------------------------------------------------------- */
/* Function: in32r */
/* Description: Input 32 bits and byte reverse */
/*------------------------------------------------------------------------------- */

	.globl	in32r
in32r:
	lwbrx	r3,r0,r3
	sync
	blr

/*------------------------------------------------------------------------------- */
/* Function: ppcDcbf */
/* Description: Data Cache block flush */
/* Input: r3 = effective address */
/* Output: none. */
/*------------------------------------------------------------------------------- */
.globl ppcDcbf
ppcDcbf:

	dcbf	r0,r3
	blr

/*------------------------------------------------------------------------------- */
/* Function: ppcDcbi */
/* Description: Data Cache block Invalidate */
/* Input: r3 = effective address */
/* Output: none. */
/*------------------------------------------------------------------------------- */
.globl ppcDcbi
ppcDcbi:

	dcbi	r0,r3
	blr

/*--------------------------------------------------------------------------
* Function: ppcDcbz
* Description: Data Cache block zero.
* Input: r3 = effective address
* Output: none.
*--------------------------------------------------------------------------
*/

.globl ppcDcbz
ppcDcbz:

	dcbz	r0,r3
	blr

/*------------------------------------------------------------------------------- */
/* Function: ppcSync */
/* Description: Processor Synchronize */
/* Input: none. */
/* Output: none. */
/*------------------------------------------------------------------------------- */
.globl ppcSync
ppcSync:
sync
blr

/*------------------------------------------------------------------------------*/

/*
* void relocate_code (addr_sp, gd, addr_moni)
*
* This "function" does not return, instead it continues in RAM
* after relocating the monitor code.
*
* r3 = dest
* r4 = src
* r5 = length in bytes
* r6 = cachelinesize
*/
.globl relocate_code
relocate_code:

	mr	r1,r3		/* Set new stack pointer		*/
	mr	r9,r4		/* Save copy of Init Data pointer	*/
	mr	r10,r5		/* Save copy of Destination Address	*/

	mr	r3,r5				/* Destination Address	*/
	lis	r4,CFG_MONITOR_BASE at h		/* Source      Address	*/
	ori	r4,r4,CFG_MONITOR_BASE at l
	lwz	r5,GOT(__init_end)
	sub	r5,r5,r4
	li	r6,CFG_CACHELINE_SIZE		/* Cache Line Size	*/

	/*
	 * Fix GOT pointer:
	 *
	 * New GOT-PTR = (old GOT-PTR - CFG_MONITOR_BASE) + Destination Address
	 *
	 * Offset:
	 */
	sub	r15,r10,r4

	/* First our own GOT */
	add	r14,r14,r15
	/* the the one used by the C code */
	add	r30,r30,r15

	/*
	 * Now relocate code
	 */

	cmplw	cr1,r3,r4
	addi	r0,r5,3
	srwi.	r0,r0,2
	beq	cr1,4f		/* In place copy is not necessary	*/
	beq	7f		/* Protect against 0 count		*/
	mtctr	r0
	bge	cr1,2f

	la	r8,-4(r4)
	la	r7,-4(r3)
1:	lwzu	r0,4(r8)
	stwu	r0,4(r7)
	bdnz	1b
	b	4f

2: slwi r0,r0,2

	add	r8,r4,r0
	add	r7,r3,r0
3:	lwzu	r0,-4(r8)
	stwu	r0,-4(r7)
	bdnz	3b

/*
* Now flush the cache: note that we must start from a cache aligned
* address. Otherwise we might miss one cache line.
*/
4: cmpwi r6,0

	add	r5,r3,r5
	beq	7f		/* Always flush prefetch queue in any case */
	subi	r0,r6,1
	andc	r3,r3,r0
	mr	r4,r3
5:	dcbst	0,r4
	add	r4,r4,r6
	cmplw	r4,r5
	blt	5b
	sync			/* Wait for all dcbst to complete on bus */
	mr	r4,r3
6:	icbi	0,r4
	add	r4,r4,r6
	cmplw	r4,r5
	blt	6b
7:	sync			/* Wait for all icbi to complete on bus */
	isync

	/*
	 * Re-point the IVPR at RAM
	 */
	mtspr	IVPR,r10

/*
* We are done. Do not return, instead branch to second part of board
* initialization, now running from RAM.
*/

	addi	r0,r10,in_ram - _start + _START_OFFSET
	mtlr	r0
	blr				/* NEVER RETURNS! */
	.globl	in_ram

in_ram:

	/*
	 * Relocation Function, r14 point to got2+0x8000
	 *
	 * Adjust got2 pointers, no need to check for 0, this code
	 * already puts a few entries in the table.
	 */
	li	r0,__got2_entries at sectoff@l
	la	r3,GOT(_GOT2_TABLE_)
	lwz	r11,GOT(_GOT2_TABLE_)
	mtctr	r0
	sub	r11,r3,r11
	addi	r3,r3,-4
1:	lwzu	r0,4(r3)
	add	r0,r0,r11
	stw	r0,0(r3)
	bdnz	1b

	/*
	 * Now adjust the fixups and the pointers to the fixups
	 * in case we need to move ourselves again.
	 */
2:	li	r0,__fixup_entries at sectoff@l
	lwz	r3,GOT(_FIXUP_TABLE_)
	cmpwi	r0,0
	mtctr	r0
	addi	r3,r3,-4
	beq	4f
3:	lwzu	r4,4(r3)
	lwzux	r0,r4,r11
	add	r0,r0,r11
	stw	r10,0(r3)
	stw	r0,0(r4)
	bdnz	3b
4:
clear_bss:
	/*
	 * Now clear BSS segment
	 */
	lwz	r3,GOT(__bss_start)
	lwz	r4,GOT(_end)

	cmplw	0,r3,r4
	beq	6f

	li	r0,0
5:
	stw	r0,0(r3)
	addi	r3,r3,4
	cmplw	0,r3,r4
	bne	5b

6:

	mr	r3,r9		/* Init Data pointer		*/
	mr	r4,r10		/* Destination Address		*/
	bl	board_init_r

	/*
	 * Copy exception vector code to low memory
	 *
	 * r3: dest_addr
	 * r7: source address, r8: end address, r9: target address
	 */
	.globl	trap_init
trap_init:
	lwz	r7,GOT(_start_of_vectors)
	lwz	r8,GOT(_end_of_vectors)

	li	r9,0x100		/* reset vector always at 0x100 */

	cmplw	0,r7,r8
	bgelr				/* return if r7>=r8 - just in case */

	mflr	r4			/* save link register		*/

1:
lwz r0,0(r7)
stw r0,0(r9)
addi r7,r7,4
addi r9,r9,4
cmplw 0,r7,r8
bne 1b

/*
* relocate hdlr' and int_return' entries */
li r7,.L_CriticalInput - _start + _START_OFFSET
bl trap_reloc
li r7,.L_MachineCheck - _start + _START_OFFSET
bl trap_reloc
li r7,.L_DataStorage - _start + _START_OFFSET
bl trap_reloc
li r7,.L_InstStorage - _start + _START_OFFSET
bl trap_reloc
li r7,.L_ExtInterrupt - _start + _START_OFFSET
bl trap_reloc
li r7,.L_Alignment - _start + _START_OFFSET
bl trap_reloc
li r7,.L_ProgramCheck - _start + _START_OFFSET
bl trap_reloc
li r7,.L_FPUnavailable - _start + _START_OFFSET
bl trap_reloc
li r7,.L_Decrementer - _start + _START_OFFSET
bl trap_reloc
li r7,.L_IntervalTimer - _start + _START_OFFSET
li r8,_end_of_vectors - _start + _START_OFFSET
2:

	bl	trap_reloc
	addi	r7,r7,0x100		/* next exception vector	*/
	cmplw	0,r7,r8
	blt	2b

	lis	r7,0x0
	mtspr	IVPR,r7

	mtlr	r4			/* restore link register	*/
	blr

	/*
	 * Function: relocate entries for one exception vector
	 */
trap_reloc:
	lwz	r0,0(r7)		/* hdlr ...			*/
	add	r0,r0,r3		/*  ... += dest_addr		*/
	stw	r0,0(r7)

	lwz	r0,4(r7)		/* int_return ...		*/
	add	r0,r0,r3		/*  ... += dest_addr		*/
	stw	r0,4(r7)

	blr

#ifdef CFG_INIT_RAM_LOCK
.globl unlock_ram_in_cache
unlock_ram_in_cache:

	/* invalidate the INIT_RAM section */
	lis	r3,(CFG_INIT_RAM_ADDR & ~31)@h
	ori	r3,r3,(CFG_INIT_RAM_ADDR & ~31)@l
	li	r4,512
	mtctr	r4
1:	icbi	r0,r3
	dcbi	r0,r3
	addi	r3,r3,32
	bdnz	1b
	sync			/* Wait for all icbi to complete on bus */
	isync
	blr

#endif
============================================================================

A quick question is, there is a FPGA(actel pixis) in mpc8544ds board, and it seems related with system
clock ??? There is no such FPGA in my board, is it the problem??

Shall I remove the pixis related code from board.h and board.c and try to configure system clock by myself ?? Still confusing.....

Thanks for any help.

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Signature · 2 lines
View this message in context: http://www.nabble.com/Please-help-for-Data-TLB-Error-in-MPC8544-tp23653353p23672726.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#3 lore raw
Quoted 8 lines
Quoted 1 line

EELADR - 0XF4010000, it is INIT_RAM address, why the

transaction with

Quoted 2 lines

address(0xF4010000) go to system bus?
It should keep in the cache due to cache lock, never out to

system bus.

I don't know why... and it just happened.... shall I allocate a entry of tlb for it?? or cover it in some space ?

Not need.

Quoted 3 lines

A quick question is, there is a FPGA(actel pixis) in mpc8544ds board, and it seems related with system clock ??? There is no such FPGA in my board, is it the problem??

It is possible to be problem.

Quoted 3 lines

Shall I remove the pixis related code from board.h and board.c and try to configure system clock by myself ?? Still confusing.....

Yes, remove the pixis related code. Configure the sys clk directly.

Thanks, Dave

author
#4 lore raw

Hi Dave,
It still shows data tlb error tho.
I found it occur error around the GET_GOT of start.s.
The SRR0 and SRR1 show the error address of system.map is _start_cont. Suspect the DDR setting problem ?? But I thought all the DDR setting are
from SPD.
So, I didn't set any entry of DDR in TLB1.
Any hint?

Quoted 31 lines · Liu Dave-R63238 wrote:
Quoted 9 lines
Quoted 2 lines

EELADR - 0XF4010000, it is INIT_RAM address, why the

transaction with

Quoted 2 lines

address(0xF4010000) go to system bus?
It should keep in the cache due to cache lock, never out to

system bus.

I don't know why... and it just happened.... shall I allocate a entry of tlb for it?? or cover it in some space ?

Not need.

Quoted 3 lines

A quick question is, there is a FPGA(actel pixis) in mpc8544ds board, and it seems related with system clock ??? There is no such FPGA in my board, is it the problem??

It is possible to be problem.

Quoted 3 lines

Shall I remove the pixis related code from board.h and board.c and try to configure system clock by myself ?? Still confusing.....

Yes, remove the pixis related code. Configure the sys clk directly.

Thanks, Dave
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Signature · 2 lines
View this message in context: http://www.nabble.com/Please-help-for-Data-TLB-Error-in-MPC8544-tp23653353p23726526.html
Sent from the Uboot - Users mailing list archive at Nabble.com.