Posted Write onto a PCI end point device using Linux
Hi,
I am wondering whether it is possible to issue a posted write using the host computer's root complex towards an PCI express end point. I have done this using
DMA in the past. However, if posted writes are possible that would save a lot of
time and effort and would be quicker too.
Thanks,
Sanka
Quoted 9 lines · Sanka Piyaratna
Hi,
I am wondering whether it is possible to issue a posted write using the host computer's root complex towards an PCI express end point. I have done this using
DMA in the past. However, if posted writes are possible that would save a lot of
time and effort and would be quicker too.
Writes from the CPU to PCI memory are always posted. However, the posted write buffer size is usually quite limited and so this probably will still cause CPU overhead when writing any significant amount of data this way.
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 4 lines · Sanka Piyaratna
Hi Robert,
Could you please tell me how I can initiate a posted write towards a PCIe endpoint with larger than 32 bit payload using Linux?
Thanks and regards,
You can try writeq to get a 64-bit payload, but I don't think it's available on all platforms. In particular with a 32-bit CPU, it may not be possible at all. If you need to send bigger payloads then you need to use DMA.
Quoted 30 lines
Sanka Piyaratna
________________________________
From: Robert Hancock <[email protected]>
To: Sanka Piyaratna <[email protected]>
Cc: [email protected]
Sent: Wed, 8 December, 2010 12:16:54 PM
Subject: Re: Posted Write onto a PCI end point device using LinuxQuoted 8 lines · Sanka Piyaratna
Hi,
I am wondering whether it is possible to issue a posted write using the host
computer's root complex towards an PCI express end point. I have done this usingQuoted 4 lines
DMA in the past. However, if posted writes are possible that would save a lot of
time and effort and would be quicker too.
Writes from the CPU to PCI memory are always posted. However, the posted write buffer size is usually quite limited and so this probably will still cause CPU overhead when writing any significant amount of data this way.
Thanks for that Robert. When you say DMA, this has to be implemented at the endpoint device doesn't it? There is no DMA mode on the CPU for doing this is there?
Sanka Piyaratna
________________________________
From: Robert Hancock <[email protected]>
To: Sanka Piyaratna <[email protected]>
Cc: [email protected]
Sent: Wed, 8 December, 2010 3:25:47 PM
Subject: Re: Posted Write onto a PCI end point device using Linux
Quoted 4 lines · Sanka Piyaratna
Hi Robert,
Could you please tell me how I can initiate a posted write towards a PCIe endpoint with larger than 32 bit payload using Linux?
Thanks and regards,
You can try writeq to get a 64-bit payload, but I don't think it's available on all platforms. In particular with a 32-bit CPU, it may not be possible at all. If you need to send bigger payloads then you need to use DMA.
Quoted 30 lines
Sanka Piyaratna
________________________________
From: Robert Hancock <[email protected]>
To: Sanka Piyaratna <[email protected]>
Cc: [email protected]
Sent: Wed, 8 December, 2010 12:16:54 PM
Subject: Re: Posted Write onto a PCI end point device using LinuxQuoted 8 lines · Sanka Piyaratna
Hi,
I am wondering whether it is possible to issue a posted write using the host
computer's root complex towards an PCI express end point. I have done this usingQuoted 4 lines
DMA in the past. However, if posted writes are possible that would save a lot of
time and effort and would be quicker too.
Writes from the CPU to PCI memory are always posted. However, the posted write buffer size is usually quite limited and so this probably will still cause CPU overhead when writing any significant amount of data this way.
Quoted 3 lines · Sanka Piyaratna
Thanks for that Robert. When you say DMA, this has to be implemented at the endpoint device doesn't it? There is no DMA mode on the CPU for doing this is there?
No, there's not (on typical hardware, anyway).
Quoted 59 lines
Sanka Piyaratna
________________________________
From: Robert Hancock <[email protected]>
To: Sanka Piyaratna <[email protected]>
Cc: [email protected]
Sent: Wed, 8 December, 2010 3:25:47 PM
Subject: Re: Posted Write onto a PCI end point device using LinuxQuoted 4 lines · Sanka Piyaratna
Hi Robert,
Could you please tell me how I can initiate a posted write towards a PCIe endpoint with larger than 32 bit payload using Linux?
Thanks and regards,You can try writeq to get a 64-bit payload, but I don't think it's available on all platforms. In particular with a 32-bit CPU, it may not be possible at all. If you need to send bigger payloads then you need to use DMA.
Quoted 30 lines
Sanka Piyaratna
________________________________
From: Robert Hancock <[email protected]>
To: Sanka Piyaratna <[email protected]>
Cc: [email protected]
Sent: Wed, 8 December, 2010 12:16:54 PM
Subject: Re: Posted Write onto a PCI end point device using LinuxQuoted 8 lines · Sanka Piyaratna
Hi,
I am wondering whether it is possible to issue a posted write using the host
computer's root complex towards an PCI express end point. I have done this usingQuoted 4 lines
DMA in the past. However, if posted writes are possible that would save a lot of
time and effort and would be quicker too.
Writes from the CPU to PCI memory are always posted. However, the posted write buffer size is usually quite limited and so this probably will still cause CPU overhead when writing any significant amount of data this way.